One of the very few warnings I have in the current build comes from
arch/x86/boot/edd.c, where I get the following with a gcc9 build:
arch/x86/boot/edd.c: In function ‘query_edd’:
arch/x86/boot/edd.c:148:11: warning: taking address of packed member of ‘struct boot_params’ may result in an unaligned pointer value [-Waddress-of-packed-member]
148 | mbrptr = boot_params.edd_mbr_sig_buffer;
| ^~~~~~~~~~~
This warning triggers because we throw away all the CFLAGS and then make
a new set for REALMODE_CFLAGS, so the -Wno-address-of-packed-member we
added in the following commit is not present:
The simplest solution for now is to adjust the warning for this version
of CFLAGS as well, but it would definitely make sense to examine whether
REALMODE_CFLAGS could be derived from CFLAGS, so that it picks up changes
in the compiler flags environment automatically.
`dev` (struct rsi_91x_usbdev *) field of adapter
(struct rsi_91x_usbdev *) is allocated and initialized in
`rsi_init_usb_interface`. If any error is detected in information
read from the device side, `rsi_init_usb_interface` will be
freed. However, in the higher level error handling code in
`rsi_probe`, if error is detected, `rsi_91x_deinit` is called
again, in which `dev` will be freed again, resulting double free.
This patch fixes the double free by removing the free operation on
`dev` in `rsi_init_usb_interface`, because `rsi_91x_deinit` is also
used in `rsi_disconnect`, in that code path, the `dev` field is not
(and thus needs to be) freed.
This bug was found in v4.19, but is also present in the latest version
of kernel. Fixes CVE-2019-15504.
The CB4063 board uses pmc_plt_clk* clocks for ethernet controllers. This
adds it to the critclk_systems DMI table so the clocks are marked as
CLK_CRITICAL and not turned off.
When CPU raise #NPF on guest data access and guest CR4.SMAP=1, it is
possible that CPU microcode implementing DecodeAssist will fail
to read bytes of instruction which caused #NPF. This is AMD errata
1096 and it happens because CPU microcode reading instruction bytes
incorrectly attempts to read code as implicit supervisor-mode data
accesses (that is, just like it would read e.g. a TSS), which are
susceptible to SMAP faults. The microcode reads CS:RIP and if it is
a user-mode address according to the page tables, the processor
gives up and returns no instruction bytes. In this case,
GuestIntrBytes field of the VMCB on a VMEXIT will incorrectly
return 0 instead of the correct guest instruction bytes.
Current KVM code attemps to detect and workaround this errata, but it
has multiple issues:
1) It mistakenly checks if guest CR4.SMAP=0 instead of guest CR4.SMAP=1,
which is required for encountering a SMAP fault.
2) It assumes SMAP faults can only occur when guest CPL==3.
However, in case guest CR4.SMEP=0, the guest can execute an instruction
which reside in a user-accessible page with CPL<3 priviledge. If this
instruction raise a #NPF on it's data access, then CPU DecodeAssist
microcode will still encounter a SMAP violation. Even though no sane
OS will do so (as it's an obvious priviledge escalation vulnerability),
we still need to handle this semanticly correct in KVM side.
Note that (2) *is* a useful optimization, because CR4.SMAP=1 is an easy
triggerable condition and guests usually enable SMAP together with SMEP.
If the vCPU has CR4.SMEP=1, the errata could indeed be encountered onlt
at guest CPL==3; otherwise, the CPU would raise a SMEP fault to guest
instead of #NPF. We keep this condition to avoid false positives in
the detection of the errata.
In addition, to avoid future confusion and improve code readbility,
include details of the errata in code and not just in commit message.
Fixes: 05d5a4863525 ("KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)") Cc: Singh Brijesh <brijesh.singh@amd.com> Cc: Sean Christopherson <sean.j.christopherson@intel.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When L0 is executing handle_invept(), the TDP MMU is active. Emulating
an L1 INVEPT does require synchronizing the appropriate shadow EPT
root(s), but a call to kvm_mmu_sync_roots in this context won't do
that. Similarly, the hardware TLB and paging-structure-cache entries
associated with the appropriate shadow EPT root(s) must be flushed,
but requesting a TLB_FLUSH from this context won't do that either.
How did this ever work? KVM always does a sync_roots and TLB flush (in
the correct context) when transitioning from L1 to L2. That isn't the
best choice for nested VM performance, but it effectively papers over
the mistakes here.
Remove the unnecessary operations and leave a comment to try to do
better in the future.
Reported-by: Junaid Shahid <junaids@google.com> Fixes: bfd0a56b90005f ("nEPT: Nested INVEPT") Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com> Cc: Nadav Har'El <nyh@il.ibm.com> Cc: Jun Nakajima <jun.nakajima@intel.com> Cc: Xinhao Xu <xinhao.xu@intel.com> Cc: Yang Zhang <yang.z.zhang@Intel.com> Cc: Gleb Natapov <gleb@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by Peter Shier <pshier@google.com> Reviewed-by: Junaid Shahid <junaids@google.com> Signed-off-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some arches (e.g., arm64, x86) have moved towards non-executable
module_alloc() allocations for security hardening reasons. That means
that the module loader will need to set the text section of a module to
executable, regardless of whether or not CONFIG_STRICT_MODULE_RWX is set.
When CONFIG_STRICT_MODULE_RWX=y, module section allocations are always
page-aligned to handle memory rwx permissions. On some arches with
CONFIG_STRICT_MODULE_RWX=n however, when setting the module text to
executable, the BUG_ON() in frob_text() gets triggered since module
section allocations are not page-aligned when CONFIG_STRICT_MODULE_RWX=n.
Since the set_memory_* API works with pages, and since we need to call
set_memory_x() regardless of whether CONFIG_STRICT_MODULE_RWX is set, we
might as well page-align all module section allocations for ease of
managing rwx permissions of module sections (text, rodata, etc).
Fixes: 2eef1399a866 ("modules: fix BUG when load module with rodata=n") Reported-by: Martin Kaiser <lists@kaiser.cx> Reported-by: Bartosz Golaszewski <brgl@bgdev.pl> Tested-by: David Lechner <david@lechnology.com> Tested-by: Martin Kaiser <martin@kaiser.cx> Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Jessica Yu <jeyu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the data type as DFSDM raw output is complements 2,
24bits left aligned in a 32-bit register.
This change does not affect AUDIO path
- Set data as signed for IIO (as for AUDIO)
- Set 8 bit right shift for IIO.
The 8 LSBs bits of data contains channel info and are masked.
In buffered mode, output samples are shifted left
unconditionally. This works for filter order 3,
but this shift is not adapted for other filter orders.
Compute required shift, left or right, and shift
output data accordingly.
Add also saturation management to avoid wrap-around
when maximum positive sample is reached.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com> Fixes: eca949800d2d ("IIO: ADC: add stm32 DFSDM support for PDM microphone") Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit has caused regressions in notebooks that support suspend
to idle such as the XPS 9360, XPS 9370 and XPS 9380.
These notebooks will wakeup from suspend to idle from an unsolicited
advertising packet from an unpaired BLE device.
In a bug report it was sugggested that this is caused by a generic
lack of LE privacy support. Revert this commit until that behavior
can be avoided by the kernel.
Each iteration of for_each_child_of_node puts the previous
node, but in the case of a goto from the middle of the loop, there is
no put, thus causing a memory leak. Hence add an of_node_put before the
goto in two places.
Issue found with Coccinelle.
Fixes: 119f5173628a (drm/mediatek: Add DRM Driver for Mediatek SoC MT8173) Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com> Signed-off-by: CK Hu <ck.hu@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Newer GPD MicroPC BIOS versions have proper DMI strings, add an extra quirk
table entry for these new strings. This is good news, as this means that we
no longer have to update the BIOS dates list with every BIOS update.
TI-SCI firmware will only respond to messages when the
TI_SCI_FLAG_REQ_ACK_ON_PROCESSED flag is set. Most messages already do
this, set this for the ones that do not.
This will be enforced in future firmware that better match the TI-SCI
specifications, this patch will not break users of existing firmware.
Fixes: aa276781a64a ("firmware: Add basic support for TI System Control Interface (TI-SCI) protocol") Signed-off-by: Andrew F. Davis <afd@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Tested-by: Alejandro Hernandez <ajhernandez@ti.com> Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For decrypt, req->cryptlen includes the size of the authentication
part while all functions of the driver expect cryptlen to be
the size of the encrypted data.
As it is not expected to change req->cryptlen, this patch
implements local calculation of cryptlen.
When data size is not a multiple of the alg's block size,
the SEC generates an error interrupt and dumps the registers.
And for NULL size, the SEC does just nothing and the interrupt
is awaited forever.
This patch ensures the data size is correct before submitting
the request to the SEC engine.
Although the HW accepts any size and silently truncates
it to the correct length, the extra tests expects EINVAL
to be returned when the key size is not valid.
// sd is freed
kernfs_new_node(sd)
kernfs_get(glue_dir)
kernfs_add_one()
kernfs_put()
Before CPU1 remove last child device under glue dir, if CPU2 add a new
device under glue dir, the glue_dir kobject reference count will be
increase to 2 via kobject_get() in get_device_parent(). And CPU2 has
been called kernfs_create_dir_ns(), but not call kernfs_new_node().
Meanwhile, CPU1 call sysfs_remove_dir() and sysfs_put(). This result in
glue_dir->sd is freed and it's reference count will be 0. Then CPU2 call
kernfs_get(glue_dir) will trigger a warning in kernfs_get() and increase
it's reference count to 1. Because glue_dir->sd is freed by CPU1, the next
call kernfs_add_one() by CPU2 will fail(This is also use-after-free)
and call kernfs_put() to decrease reference count. Because the reference
count is decremented to 0, it will also call kmem_cache_free() to free
the glue_dir->sd again. This will result in double free.
In order to avoid this happening, we also should make sure that kernfs_node
for glue_dir is released in CPU1 only when refcount for glue_dir kobj is
1 to fix this race.
The following calltrace is captured in kernel 4.14 with the following patch
applied:
commit 726e41097920 ("drivers: core: Remove glue dirs from sysfs earlier")
Commit c877154d307f fixed an uninitialized variable and optimized
the function to not call tnc_next() in the first iteration of the
loop. While this seemed perfectly legit and wise, it turned out to
be illegal.
If the lookup function does not find an exact match it will rewind
the cursor by 1.
The rewinded cursor will not match the name hash we are looking for
and this results in a spurious -ENOENT.
So we need to move to the next entry in case of an non-exact match,
but not if the match was exact.
While we are here, update the documentation to avoid further confusion.
Commit 0e7df22401a3 ("PCI: Add sysfs sriov_drivers_autoprobe to control
VF driver binding") introduced the sriov_drivers_autoprobe attribute
which allows users to prevent the kernel from automatically probing a
driver for new VFs as they are created. This allows VFs to be spawned
without automatically binding the new device to a host driver, such as
in cases where the user intends to use the device only with a meta
driver like vfio-pci. However, the current implementation prevents any
use of drivers_probe with the VF while sriov_drivers_autoprobe=0. This
blocks the now current general practice of setting driver_override
followed by using drivers_probe to bind a device to a specified driver.
The kernel never automatically sets a driver_override therefore it seems
we can assume a driver_override reflects the intent of the user. Also,
probing a device using a driver_override match seems outside the scope
of the 'auto' part of sriov_drivers_autoprobe. Therefore, let's allow
driver_override matches regardless of sriov_drivers_autoprobe, which we
can do by simply testing if a driver_override is set for a device as a
'can probe' condition.
One main goal of the function mtk_nfc_update_ecc_stats is to check
whether sectors are all empty. If they are empty, set these sectors's
data buffer and OOB buffer as 0xff.
But now, the sector OOB buffer pointer is wrongly assigned. We always
do memset from sector 0.
To fix this issue, pass start sector number to make OOB buffer pointer
be properly assigned.
At boot time, my rk3288-veyron devices yell with 8 lines that look
like this:
[ 0.000000] rockchip_mmc_get_phase: invalid clk rate
This is because the clock framework at clk_register() time tries to
get the phase but we don't have a parent yet.
While the errors appear to be harmless they are still ugly and, in
general, we don't want yells like this in the log unless they are
important.
There's no real reason to be yelling here. We can still return
-EINVAL to indicate that the phase makes no sense without a parent.
If someone really tries to do tuning and the clock is reported as 0
then we'll see the yells in rockchip_mmc_set_phase().
Fixes: 4bf59902b500 ("clk: rockchip: Prevent calculating mmc phase if clock rate is zero") Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that "mvif->omac_idx" is a u8 so it can't be negative
and the error handling won't work. The get_omac_idx() function returns
-1 on error.
Fixes: 04b8e65922f6 ("mt76: add mac80211 driver for MT7615 PCIe-based chipsets") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The possible parent printing function duplicates a bunch of if
conditions. Pull that into another function so we can print an extra
character at the end, either a space or a newline. This way we can add
the required newline that got lost here and also shorten the code.
Following the commit fc0c209c147f ("clk: Allow parents to be specified
without string names"), the parent name string is not always populated.
Instead, fetch the parents clk_core struct using the appropriate helper,
and read its name directly. If that fails, go through the possible
sources of parent names. The order in which they are used is different
from how parents are looked up, with the global name having precedence
over local fw_name and indices. This makes more sense as a) the
parent_maps structure does not differentiate between legacy global names
and fallback global names, and b) global names likely provide more
information than local fw_names.
Fixes: fc0c209c147f ("clk: Allow parents to be specified without string names") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
3a63f70bf4c3a ("x86/boot: Early parse RSDP and save it in boot_params")
broke kexec boot on EFI systems. efi_get_rsdp_addr() in the early
parsing code tries to search RSDP from the EFI tables but that will
crash because the table address is virtual when the kernel was booted by
kexec (set_virtual_address_map() has run in the first kernel and cannot
be run again in the second kernel).
In the case of kexec, the physical address of EFI tables is provided via
efi_setup_data in boot_params, which is set up by kexec(1).
Factor out the table parsing code and use different pointers depending
on whether the kernel is booted by kexec or not.
[ bp: Massage. ]
Fixes: 3a63f70bf4c3a ("x86/boot: Early parse RSDP and save it in boot_params") Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com> Signed-off-by: Borislav Petkov <bp@suse.de> Tested-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Cc: Chao Fan <fanc.fnst@cn.fujitsu.com> Cc: Dave Young <dyoung@redhat.com> Link: https://lkml.kernel.org/r/20190408231011.GA5402@jeru.linux.bs1.fc.nec.co.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ddf35cf3764b ("powerpc: Use barrier_nospec in copy_from_user()")
Added barrier_nospec before loading from user-controlled pointers. The
intention was to order the load from the potentially user-controlled
pointer vs a previous branch based on an access_ok() check or similar.
In order to achieve the same result, add a barrier_nospec to the
raw_copy_in_user() function before loading from such a user-controlled
pointer.
Fixes: ddf35cf3764b ("powerpc: Use barrier_nospec in copy_from_user()") Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The last change to this Makefile caused relocation errors when loading
a kdump kernel. Restore -mcmodel=large (not -mcmodel=kernel),
-ffreestanding, and -fno-zero-initialized-bsss, without reverting to
the former practice of resetting KBUILD_CFLAGS.
Purgatory.ro is a standalone binary that is not linked against the
rest of the kernel. Its image is copied into an array that is linked
to the kernel, and from there kexec relocates it wherever it desires.
With the previous change to compiler flags, the error "kexec: Overflow
in relocation type 11 value 0x11fffd000" was encountered when trying
to load the crash kernel. This is from kexec code trying to relocate
the purgatory.ro object.
From the error message, relocation type 11 is R_X86_64_32S. The
x86_64 ABI says:
"The R_X86_64_32 and R_X86_64_32S relocations truncate the
computed value to 32-bits. The linker must verify that the
generated value for the R_X86_64_32 (R_X86_64_32S) relocation
zero-extends (sign-extends) to the original 64-bit value."
This type of relocation doesn't work when kexec chooses to place the
purgatory binary in memory that is not reachable with 32 bit
addresses.
The compiler flag -mcmodel=kernel allows those type of relocations to
be emitted, so revert to using -mcmodel=large as was done before.
Also restore the -ffreestanding and -fno-zero-initialized-bss flags
because they are appropriate for a stand alone piece of object code
which doesn't explicitly zero the bss, and one other report has said
undefined symbols are encountered without -ffreestanding.
These identical compiler flag changes need to happen for every object
that becomes part of the purgatory.ro object, so gather them together
first into PURGATORY_CFLAGS_REMOVE and PURGATORY_CFLAGS, and then
apply them to each of the objects that have C source. Do not apply
any of these flags to kexec-purgatory.o, which is not part of the
standalone object but part of the kernel proper.
Tested-by: Vaibhav Rustagi <vaibhavrustagi@google.com> Tested-by: Andreas Smas <andreas@lonelycoder.com> Signed-off-by: Steve Wahl <steve.wahl@hpe.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: None Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: clang-built-linux@googlegroups.com Cc: dimitri.sivanich@hpe.com Cc: mike.travis@hpe.com Cc: russ.anderson@hpe.com Fixes: b059f801a937 ("x86/purgatory: Use CFLAGS_REMOVE rather than reset KBUILD_CFLAGS") Link: https://lkml.kernel.org/r/20190905202346.GA26595@swahl-linux Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Andreas Smas <andreas@lonelycoder.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Harvey reported a livelock that was introduced by commit d012a06ab1d23 ("Revert "KVM: x86/mmu: Zap only the relevant pages when
removing a memslot"").
The livelock occurs because kvm_mmu_zap_all() as it exists today will
voluntarily reschedule and drop KVM's mmu_lock, which allows other vCPUs
to add shadow pages. With enough vCPUs, kvm_mmu_zap_all() can get stuck
in an infinite loop as it can never zap all pages before observing lock
contention or the need to reschedule. The equivalent of kvm_mmu_zap_all()
that was in use at the time of the reverted commit (4e103134b8623, "KVM:
x86/mmu: Zap only the relevant pages when removing a memslot") employed
a fast invalidate mechanism and was not susceptible to the above livelock.
There are three ways to fix the livelock:
- Reverting the revert (commit d012a06ab1d23) is not a viable option as
the revert is needed to fix a regression that occurs when the guest has
one or more assigned devices. It's unlikely we'll root cause the device
assignment regression soon enough to fix the regression timely.
- Remove the conditional reschedule from kvm_mmu_zap_all(). However, although
removing the reschedule would be a smaller code change, it's less safe
in the sense that the resulting kvm_mmu_zap_all() hasn't been used in
the wild for flushing memslots since the fast invalidate mechanism was
introduced by commit 6ca18b6950f8d ("KVM: x86: use the fast way to
invalidate all pages"), back in 2013.
- Reintroduce the fast invalidate mechanism and use it when zapping shadow
pages in response to a memslot being deleted/moved, which is what this
patch does.
For all intents and purposes, this is a revert of commit ea145aacf4ae8
("Revert "KVM: MMU: fast invalidate all pages"") and a partial revert of
commit 7390de1e99a70 ("Revert "KVM: x86: use the fast way to invalidate
all pages""), i.e. restores the behavior of commit 5304b8d37c2a5 ("KVM:
MMU: fast invalidate all pages") and commit 6ca18b6950f8d ("KVM: x86:
use the fast way to invalidate all pages") respectively.
Fixes: d012a06ab1d23 ("Revert "KVM: x86/mmu: Zap only the relevant pages when removing a memslot"") Reported-by: James Harvey <jamespharvey20@gmail.com> Cc: Alex Willamson <alex.williamson@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emulation of VMPTRST can incorrectly inject a page fault
when passed an operand that points to an MMIO address.
The page fault will use uninitialized kernel stack memory
as the CR2 and error code.
The right behavior would be to abort the VM with a KVM_EXIT_INTERNAL_ERROR
exit to userspace; however, it is not an easy fix, so for now just ensure
that the error code and CR2 are zero.
When the userspace program runs the KVM_S390_INTERRUPT ioctl to inject
an interrupt, we convert them from the legacy struct kvm_s390_interrupt
to the new struct kvm_s390_irq via the s390int_to_s390irq() function.
However, this function does not take care of all types of interrupts
that we can inject into the guest later (see do_inject_vcpu()). Since we
do not clear out the s390irq values before calling s390int_to_s390irq(),
there is a chance that we copy random data from the kernel stack which
could be leaked to the userspace later.
Specifically, the problem exists with the KVM_S390_INT_PFAULT_INIT
interrupt: s390int_to_s390irq() does not handle it, and the function
__inject_pfault_init() later copies irq->u.ext which contains the
random kernel stack data. This data can then be leaked either to
the guest memory in __deliver_pfault_init(), or the userspace might
retrieve it directly with the KVM_S390_GET_IRQ_STATE ioctl.
Fix it by handling that interrupt type in s390int_to_s390irq(), too,
and by making sure that the s390irq struct is properly pre-initialized.
And while we're at it, make sure that s390int_to_s390irq() now
directly returns -EINVAL for unknown interrupt types, so that we
immediately get a proper error code in case we add more interrupt
types to do_inject_vcpu() without updating s390int_to_s390irq()
sometime in the future.
Cc: stable@vger.kernel.org Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Janosch Frank <frankja@linux.ibm.com> Signed-off-by: Thomas Huth <thuth@redhat.com> Link: https://lore.kernel.org/kvm/20190912115438.25761-1-thuth@redhat.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_opp_supported_by_regulators() wrongly ignored errors from
regulator_is_supported_voltage(), so it considered errors as
success. Since
commit 498209445124 ("regulator: core: simplify return value on suported_voltage")
regulator_is_supported_voltage() returns a real boolean, so
errors make _opp_supported_by_regulators() return false.
That reveals a problem with the declaration of the VDD1/2
regulators on twl4030.
The VDD1/VDD2 regulators on twl4030 are neither defined with
voltage lists nor with the continuous flag set, so
regulator_is_supported_voltage() returns false and an error
before above mentioned commit (which was considered success)
The result is that after the above mentioned commit cpufreq
does not work properly e.g. dm3730.
[ 2.490997] core: _opp_supported_by_regulators: OPP minuV: 1012500 maxuV: 1012500, not supported by regulator
[ 2.501617] cpu cpu0: _opp_add: OPP not supported by regulators (300000000)
[ 2.509246] core: _opp_supported_by_regulators: OPP minuV: 1200000 maxuV: 1200000, not supported by regulator
[ 2.519775] cpu cpu0: _opp_add: OPP not supported by regulators (600000000)
[ 2.527313] core: _opp_supported_by_regulators: OPP minuV: 1325000 maxuV: 1325000, not supported by regulator
[ 2.537750] cpu cpu0: _opp_add: OPP not supported by regulators (800000000)
The patch fixes declaration of VDD1/2 regulators by
adding proper voltage lists.
Fixes: 498209445124 ("regulator: core: simplify return value on suported_voltage") Cc: stable@vger.kernel.org Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit Link: https://lore.kernel.org/r/20190814214319.24087-1-andreas@kemnade.info Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unable to handle kernel NULL pointer dereference at 0000000000000158
Internal error: Oops: 96000004 [#1] SMP
pc : resend_irqs+0x68/0xb0
lr : resend_irqs+0x64/0xb0
...
Call trace:
resend_irqs+0x68/0xb0
tasklet_action_common.isra.6+0x84/0x138
tasklet_action+0x2c/0x38
__do_softirq+0x120/0x324
run_ksoftirqd+0x44/0x60
smpboot_thread_fn+0x1ac/0x1e8
kthread+0x134/0x138
ret_from_fork+0x10/0x18
The reason for this is that the interrupt resend mechanism happens in soft
interrupt context, which is a asynchronous mechanism versus other
operations on interrupts. free_irq() does not take resend handling into
account. Thus, the irq descriptor might be already freed before the resend
tasklet is executed. resend_irqs() does not check the return value of the
interrupt descriptor lookup and derefences the return value
unconditionally.
MT7630E hardware does support 5GHz, but we do not properly configure phy
for 5GHz channels. Scanning at this band not only do not show any APs
but also can hang the firmware.
Since vendor reference driver do not support 5GHz we don't know how
properly configure 5GHz channels. So disable this band for MT7630E .
Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by 9ad3b5565445 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Cc: <stable@vger.kernel.org> # v5.1+ Reported-and-tested-by: Sergey Maranchuk <slav0nic0@gmail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were a couple cases where the ITR value generated via the adaptive
ITR scheme could exceed 126. This resulted in the value becoming either 0
or something less than 10. Switching back and forth between a value less
than 10 and a value greater than 10 can cause issues as certain hardware
features such as RSC to not function well when the ITR value has dropped
that low.
CC: stable@vger.kernel.org Fixes: b4ded8327fea ("ixgbe: Update adaptive ITR algorithm") Reported-by: Gregg Leventhal <gleventhal@janestreet.com> Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tx code doesn't clear the descriptors' status after cleaning.
So, if the budget is larger than number of used elems in a ring, some
descriptors will be accounted twice and xsk_umem_complete_tx will move
prod_tail far beyond the prod_head breaking the completion queue ring.
Fix that by limiting the number of descriptors to clean by the number
of used descriptors in the Tx ring.
'ixgbe_clean_xdp_tx_irq()' function refactored to look more like
'ixgbe_xsk_clean_tx_ring()' since we're allowed to directly use
'next_to_clean' and 'next_to_use' indexes.
CC: stable@vger.kernel.org Fixes: 8221c5eba8c1 ("ixgbe: add AF_XDP zero-copy Tx support") Signed-off-by: Ilya Maximets <i.maximets@samsung.com> Tested-by: William Tu <u9012063@gmail.com> Tested-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matt bisected a sparc64 specific issue with semctl, shmctl and msgctl
to a commit from my y2038 series in linux-5.1, as I missed the custom
sys_ipc() wrapper that sparc64 uses in place of the generic version that
I patched.
The problem is that the sys_{sem,shm,msg}ctl() functions in the kernel
now do not allow being called with the IPC_64 flag any more, resulting
in a -EINVAL error when they don't recognize the command.
Instead, the correct way to do this now is to call the internal
ksys_old_{sem,shm,msg}ctl() functions to select the API version.
As we generally move towards these functions anyway, change all of
sparc_ipc() to consistently use those in place of the sys_*() versions,
and move the required ksys_*() declarations into linux/syscalls.h
The IS_ENABLED(CONFIG_SYSVIPC) check is required to avoid link
errors when ipc is disabled.
As Vincent noticed, the y2038 conversion of semtimedop in linux-5.1
broke when commit 00bf25d693e7 ("y2038: use time32 syscall names on
32-bit") changed all system calls on all architectures that take
a 32-bit time_t to point to the _time32 implementation, but left out
semtimedop in the asm-generic header.
This affects all 32-bit architectures using asm-generic/unistd.h:
h8300, unicore32, openrisc, nios2, hexagon, c6x, arc, nds32 and csky.
The notable exception is riscv32, which has dropped support for the
time32 system calls entirely.
Reported-by: Vincent Chen <deanbo422@gmail.com> Cc: stable@vger.kernel.org Cc: Vincent Chen <deanbo422@gmail.com> Cc: Greentime Hu <green.hu@gmail.com> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Guan Xuetao <gxt@pku.edu.cn> Cc: Stafford Horne <shorne@gmail.com> Cc: Jonas Bonn <jonas@southpole.se> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Ley Foon Tan <lftan@altera.com> Cc: Richard Kuo <rkuo@codeaurora.org> Cc: Mark Salter <msalter@redhat.com> Cc: Aurelien Jacquiot <jacquiot.aurelien@gmail.com> Cc: Guo Ren <guoren@kernel.org> Fixes: 00bf25d693e7 ("y2038: use time32 syscall names on 32-bit") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bit was fliped on for "syncing dependencies between camera and
graphics". BSpec has no recollection why, and it is causing
unrecoverable GPU hangs with Vulkan compute workloads.
From BSpec, setting bit5 to 0 enables relaxed padding requirements for
buffers, 1D and 2D non-array, non-MSAA, non-mip-mapped linear surfaces;
and *must* be set to 0h on skl+ to ensure "Out of Bounds" case is
suppressed.
Reported-by: Jason Ekstrand <jason@jlekstrand.net> Suggested-by: Jason Ekstrand <jason@jlekstrand.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=110998 Fixes: 8424171e135c ("drm/i915/gen9: h/w w/a: syncing dependencies between camera and graphics") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Tested-by: denys.kostin@globallogic.com Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: <stable@vger.kernel.org> # v4.1+ Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190904100707.7377-1-chris@chris-wilson.co.uk
(cherry picked from commit 9d7b01e93526efe79dbf75b69cc5972b5a4f7b37) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
My attempt at allowing MST to use the higher color depths has
regressed some configurations. Apparently people have setups
where all MST streams will fit into the DP link with 8bpc but
won't fit with higher color depths.
What we really should be doing is reducing the bpc for all the
streams on the same link until they start to fit. But that requires
a bit more work, so in the meantime let's revert back closer to
the old behavior and limit MST to at most 8bpc.
Cc: stable@vger.kernel.org Cc: Lyude Paul <lyude@redhat.com> Tested-by: Geoffrey Bennett <gmux22@gmail.com> Fixes: f1477219869c ("drm/i915: Remove the 8bpc shackles from DP MST")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111505 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190828102059.2512-1-ville.syrjala@linux.intel.com Reviewed-by: Lyude Paul <lyude@redhat.com>
(cherry picked from commit 75427b2a2bffc083d51dec389c235722a9c69b05) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tmio_mmc_host_probe() calls pm_runtime_set_active() to update the
runtime PM status of the device, as to make it reflect the current status
of the HW. This works fine for most cases, but unfortunate not for all.
Especially, there is a generic problem when the device has a genpd attached
and that genpd have the ->start|stop() callbacks assigned.
More precisely, if the driver calls pm_runtime_set_active() during
->probe(), genpd does not get to invoke the ->start() callback for it,
which means the HW isn't really fully powered on. Furthermore, in the next
phase, when the device becomes runtime suspended, genpd will invoke the
->stop() callback for it, potentially leading to usage count imbalance
problems, depending on what's implemented behind the callbacks of course.
To fix this problem, convert to call pm_runtime_get_sync() from
tmio_mmc_host_probe() rather than pm_runtime_set_active(). Additionally, to
avoid bumping usage counters and unnecessary re-initializing the HW the
first time the tmio driver's ->runtime_resume() callback is called,
introduce a state flag to keeping track of this.
This commit broke eMMC storage access on a new consumer MiniPC based on
AMD SoC, which has eMMC connected to:
02:00.0 SD Host controller: O2 Micro, Inc. Device 8620 (rev 01) (prog-if 01)
Subsystem: O2 Micro, Inc. Device 0002
During probe, several errors are seen including:
mmc1: Got data interrupt 0x02000000 even though no data operation was in progress.
mmc1: Timeout waiting for hardware interrupt.
mmc1: error -110 whilst initialising MMC card
Reverting this commit allows the eMMC storage to be detected & usable
again.
Signed-off-by: Daniel Drake <drake@endlessm.com> Fixes: 414126f9e5ab ("mmc: sdhci: Remove unneeded quirk2 flag of O2 SD host
controller") Cc: stable@vger.kernel.org # v5.1+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 37fefadee8bb ("mmc: bcm2835: Terminate timeout work
synchronously") causes lockups in case of hardware timeouts due the
timeout work also calling cancel_delayed_work_sync() on its own.
So revert it.
If a new child cgroup is created in the frozen cgroup hierarchy
(one or more of ancestor cgroups is frozen), the CGRP_FREEZE cgroup
flag should be set. Otherwise if a process will be attached to the
child cgroup, it won't become frozen.
The problem can be reproduced with the test_cgfreezer_mkdir test.
This is the output before this patch:
~/test_freezer
ok 1 test_cgfreezer_simple
ok 2 test_cgfreezer_tree
ok 3 test_cgfreezer_forkbomb
Cgroup /sys/fs/cgroup/cg_test_mkdir_A/cg_test_mkdir_B isn't frozen
not ok 4 test_cgfreezer_mkdir
ok 5 test_cgfreezer_rmdir
ok 6 test_cgfreezer_migrate
ok 7 test_cgfreezer_ptrace
ok 8 test_cgfreezer_stopped
ok 9 test_cgfreezer_ptraced
ok 10 test_cgfreezer_vfork
And with this patch:
~/test_freezer
ok 1 test_cgfreezer_simple
ok 2 test_cgfreezer_tree
ok 3 test_cgfreezer_forkbomb
ok 4 test_cgfreezer_mkdir
ok 5 test_cgfreezer_rmdir
ok 6 test_cgfreezer_migrate
ok 7 test_cgfreezer_ptrace
ok 8 test_cgfreezer_stopped
ok 9 test_cgfreezer_ptraced
ok 10 test_cgfreezer_vfork
Sometimes when fsync'ing a file we need to log that other inodes exist and
when we need to do that we acquire a reference on the inodes and then drop
that reference using iput() after logging them.
That generally is not a problem except if we end up doing the final iput()
(dropping the last reference) on the inode and that inode has a link count
of 0, which can happen in a very short time window if the logging path
gets a reference on the inode while it's being unlinked.
In that case we end up getting the eviction callback, btrfs_evict_inode(),
invoked through the iput() call chain which needs to drop all of the
inode's items from its subvolume btree, and in order to do that, it needs
to join a transaction at the helper function evict_refill_and_join().
However because the task previously started a transaction at the fsync
handler, btrfs_sync_file(), it has current->journal_info already pointing
to a transaction handle and therefore evict_refill_and_join() will get
that transaction handle from btrfs_join_transaction(). From this point on,
two different problems can happen:
1) evict_refill_and_join() will often change the transaction handle's
block reserve (->block_rsv) and set its ->bytes_reserved field to a
value greater than 0. If evict_refill_and_join() never commits the
transaction, the eviction handler ends up decreasing the reference
count (->use_count) of the transaction handle through the call to
btrfs_end_transaction(), and after that point we have a transaction
handle with a NULL ->block_rsv (which is the value prior to the
transaction join from evict_refill_and_join()) and a ->bytes_reserved
value greater than 0. If after the eviction/iput completes the inode
logging path hits an error or it decides that it must fallback to a
transaction commit, the btrfs fsync handle, btrfs_sync_file(), gets a
non-zero value from btrfs_log_dentry_safe(), and because of that
non-zero value it tries to commit the transaction using a handle with
a NULL ->block_rsv and a non-zero ->bytes_reserved value. This makes
the transaction commit hit an assertion failure at
btrfs_trans_release_metadata() because ->bytes_reserved is not zero but
the ->block_rsv is NULL. The produced stack trace for that is like the
following:
2) If evict_refill_and_join() decides to commit the transaction, it will
be able to do it, since the nested transaction join only increments the
transaction handle's ->use_count reference counter and it does not
prevent the transaction from getting committed. This means that after
eviction completes, the fsync logging path will be using a transaction
handle that refers to an already committed transaction. What happens
when using such a stale transaction can be unpredictable, we are at
least having a use-after-free on the transaction handle itself, since
the transaction commit will call kmem_cache_free() against the handle
regardless of its ->use_count value, or we can end up silently losing
all the updates to the log tree after that iput() in the logging path,
or using a transaction handle that in the meanwhile was allocated to
another task for a new transaction, etc, pretty much unpredictable
what can happen.
In order to fix both of them, instead of using iput() during logging, use
btrfs_add_delayed_iput(), so that the logging path of fsync never drops
the last reference on an inode, that step is offloaded to a safe context
(usually the cleaner kthread).
The assertion failure issue was sporadically triggered by the test case
generic/475 from fstests, which loads the dm error target while fsstress
is running, which lead to fsync failing while logging inodes with -EIO
errors and then trying later to commit the transaction, triggering the
assertion failure.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Another day; another DSDT bug we need to workaround...
Since commit ca876c7483b6 ("gpiolib-acpi: make sure we trigger edge events
at least once on boot") we call _AEI edge handlers at boot.
In some rare cases this causes problems. One example of this is the Minix
Neo Z83-4 mini PC, this device has a clear DSDT bug where it has some copy
and pasted code for dealing with Micro USB-B connector host/device role
switching, while the mini PC does not even have a micro-USB connector.
This code, which should not be there, messes with the DDC data pin from
the HDMI connector (switching it to GPIO mode) breaking HDMI support.
To avoid problems like this, this commit adds a new
gpiolib_acpi.run_edge_events_on_boot kernel commandline option, which
allows disabling the running of _AEI edge event handlers at boot.
The default value is -1/auto which uses a DMI based blacklist, the initial
version of this blacklist contains the Neo Z83-4 fixing the HDMI breakage.
Cc: stable@vger.kernel.org Cc: Daniel Drake <drake@endlessm.com> Cc: Ian W MORRISON <ianwmorrison@gmail.com> Reported-by: Ian W MORRISON <ianwmorrison@gmail.com> Suggested-by: Ian W MORRISON <ianwmorrison@gmail.com> Fixes: ca876c7483b6 ("gpiolib-acpi: make sure we trigger edge events at least once on boot") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20190827202835.213456-1-hdegoede@redhat.com Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Ian W MORRISON <ianwmorrison@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sock_map and ULP only work together when ULP is loaded after the sock
map is loaded. In the sock_map case we added a check for this to fail
the load if ULP is already set. However, we missed the check on the
sock_hash side.
Add a ULP check to the sock_hash update path.
Fixes: 604326b41a6fb ("bpf, sockmap: convert to generic sk_msg interface") Reported-by: syzbot+7a6ee4d0078eac6bf782@syzkaller.appspotmail.com Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue causes SCTP_PEER_ADDR_THLDS sockopt not to be able to dump
a transport thresholds info.
Fix it by adding 'goto' put_user in sctp_getsockopt_paddr_thresholds.
Fixes: 8add543e369d ("sctp: add SCTP_FUTURE_ASSOC for SCTP_PEER_ADDR_THLDS sockopt") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add forward declaration for struct gpio_desc in order to address
the following:
./include/linux/phy_fixed.h:48:17: error: 'struct gpio_desc' declared inside parameter list [-Werror]
./include/linux/phy_fixed.h:48:17: error: its scope is only this definition or declaration, which is probably not what you want [-Werror]
Fixes: 71bd106d2567 ("net: fixed-phy: Add fixed_phy_register_with_gpiod() API") Signed-off-by: Moritz Fischer <mdf@kernel.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes a stupid bug I recently introduced...
ip6_route_info_create() returns an ERR_PTR(err) and not a NULL on error.
Fixes: d55a2e374a94 ("net-ipv6: fix excessive RTF_ADDRCONF flag on ::1/128 local route (and others)'") Cc: David Ahern <dsahern@gmail.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Maciej Żenczykowski <maze@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a subtle change in behaviour introduced by:
commit c7a1ce397adacaf5d4bb2eab0a738b5f80dc3e43
'ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create'
ie. the above commit causes the ::1/128 local (automatic) route to be flagged with RTF_ADDRCONF (0x040000).
AFAICT, this is incorrect since these routes are *not* coming from RA's.
As such, this patch restores the old behaviour.
Fixes: c7a1ce397ada ("ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create") Cc: David Ahern <dsahern@gmail.com> Cc: Lorenzo Colitti <lorenzo@google.com> Signed-off-by: Maciej Żenczykowski <maze@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tun_chr_read_iter() accessed the memory which freed by free_netdev()
called by tun_set_iff():
CPUA CPUB
tun_set_iff()
alloc_netdev_mqs()
tun_attach()
tun_chr_read_iter()
tun_get()
tun_do_read()
tun_ring_recv()
register_netdevice() <-- inject error
goto err_detach
tun_detach_all() <-- set RCV_SHUTDOWN
free_netdev() <-- called from
err_free_dev path
netdev_freemem() <-- free the memory
without check refcount
(In this path, the refcount cannot prevent
freeing the memory of dev, and the memory
will be used by dev_put() called by
tun_chr_read_iter() on CPUB.)
(Break from tun_ring_recv(),
because RCV_SHUTDOWN is set)
tun_put()
dev_put() <-- use the memory
freed by netdev_freemem()
Put the publishing of tfile->tun after register_netdevice(),
so tun_get() won't get the tun pointer that freed by
err_detach path if register_netdevice() failed.
Fixes: eb0fb363f920 ("tuntap: attach queue 0 before registering netdevice") Reported-by: Hulk Robot <hulkci@huawei.com> Suggested-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 97ede29e80ee ("tipc: convert name table read-write lock to RCU") Reported-by: Li Shuang <shuali@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix tcp_ecn_withdraw_cwr() to clear the correct bit:
TCP_ECN_QUEUE_CWR.
Rationale: basically, TCP_ECN_DEMAND_CWR is a bit that is purely about
the behavior of data receivers, and deciding whether to reflect
incoming IP ECN CE marks as outgoing TCP th->ece marks. The
TCP_ECN_QUEUE_CWR bit is purely about the behavior of data senders,
and deciding whether to send CWR. The tcp_ecn_withdraw_cwr() function
is only called from tcp_undo_cwnd_reduction() by data senders during
an undo, so it should zero the sender-side state,
TCP_ECN_QUEUE_CWR. It does not make sense to stop the reflection of
incoming CE bits on incoming data packets just because outgoing
packets were spuriously retransmitted.
The bug has been reproduced with packetdrill to manifest in a scenario
with RFC3168 ECN, with an incoming data packet with CE bit set and
carrying a TCP timestamp value that causes cwnd undo. Before this fix,
the IP CE bit was ignored and not reflected in the TCP ECE header bit,
and sender sent a TCP CWR ('W') bit on the next outgoing data packet,
even though the cwnd reduction had been undone. After this fix, the
sender properly reflects the CE bit and does not set the W bit.
Note: the bug actually predates 2005 git history; this Fixes footer is
chosen to be the oldest SHA1 I have tested (from Sep 2007) for which
the patch applies cleanly (since before this commit the code was in a
.h file).
Fixes: bdf1ee5d3bd3 ("[TCP]: Move code from tcp_ecn.h to tcp*.c and tcp.h & remove it") Signed-off-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever MQ is not used on a multiqueue device, we experience
serious reordering problems. Bisection found the cited
commit.
The issue can be described this way :
- A single qdisc hierarchy is shared by all transmit queues.
(eg : tc qdisc replace dev eth0 root fq_codel)
- When/if try_bulk_dequeue_skb_slow() dequeues a packet targetting
a different transmit queue than the one used to build a packet train,
we stop building the current list and save the 'bad' skb (P1) in a
special queue. (bad_txq)
- When dequeue_skb() calls qdisc_dequeue_skb_bad_txq() and finds this
skb (P1), it checks if the associated transmit queues is still in frozen
state. If the queue is still blocked (by BQL or NIC tx ring full),
we leave the skb in bad_txq and return NULL.
- dequeue_skb() calls q->dequeue() to get another packet (P2)
The other packet can target the problematic queue (that we found
in frozen state for the bad_txq packet), but another cpu just ran
TX completion and made room in the txq that is now ready to accept
new packets.
- Packet P2 is sent while P1 is still held in bad_txq, P1 might be sent
at next round. In practice P2 is the lead of a big packet train
(P2,P3,P4 ...) filling the BQL budget and delaying P1 by many packets :/
To solve this problem, we have to block the dequeue process as long
as the first packet in bad_txq can not be sent. Reordering issues
disappear and no side effects have been seen.
Fixes: a53851e2c321 ("net: sched: explicit locking in gso_cpu fallback") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: John Fastabend <john.fastabend@gmail.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Regarding to IEEE 802.3-2015 standard section 2
28B.3 Priority resolution - Table 28-3 - Pause resolution
In case of Local device Pause=1 AsymDir=0, Link partner
Pause=1 AsymDir=1, Local device resolution should be enable PAUSE
transmit, disable PAUSE receive.
And in case of Local device Pause=1 AsymDir=1, Link partner
Pause=1 AsymDir=0, Local device resolution should be enable PAUSE
receive, disable PAUSE transmit.
Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Stefan Chulski <stefanc@marvell.com> Reported-by: Shaul Ben-Mayor <shaulb@marvell.com> Acked-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Historically, support for frag_list packets entering skb_segment() was
limited to frag_list members terminating on exact same gso_size
boundaries. This is verified with a BUG_ON since commit 89319d3801d1
("net: Add frag_list support to skb_segment"), quote:
As such we require all frag_list members terminate on exact MSS
boundaries. This is checked using BUG_ON.
As there should only be one producer in the kernel of such packets,
namely GRO, this requirement should not be difficult to maintain.
However, since commit 6578171a7ff0 ("bpf: add bpf_skb_change_proto helper"),
the "exact MSS boundaries" assumption no longer holds:
An eBPF program using bpf_skb_change_proto() DOES modify 'gso_size', but
leaves the frag_list members as originally merged by GRO with the
original 'gso_size'. Example of such programs are bpf-based NAT46 or
NAT64.
This lead to a kernel BUG_ON for flows involving:
- GRO generating a frag_list skb
- bpf program performing bpf_skb_change_proto() or bpf_skb_adjust_room()
- skb_segment() of the skb
See example BUG_ON reports in [0].
In commit 13acc94eff12 ("net: permit skb_segment on head_frag frag_list skb"),
skb_segment() was modified to support the "gso_size mangling" case of
a frag_list GRO'ed skb, but *only* for frag_list members having
head_frag==true (having a page-fragment head).
Alas, GRO packets having frag_list members with a linear kmalloced head
(head_frag==false) still hit the BUG_ON.
This commit adds support to skb_segment() for a 'head_skb' packet having
a frag_list whose members are *non* head_frag, with gso_size mangled, by
disabling SG and thus falling-back to copying the data from the given
'head_skb' into the generated segmented skbs - as suggested by Willem de
Bruijn [1].
Since this approach involves the penalty of skb_copy_and_csum_bits()
when building the segments, care was taken in order to enable this
solution only when required:
- untrusted gso_size, by testing SKB_GSO_DODGY is set
(SKB_GSO_DODGY is set by any gso_size mangling functions in
net/core/filter.c)
- the frag_list is non empty, its item is a non head_frag, *and* the
headlen of the given 'head_skb' does not match the gso_size.
Fixes: 6578171a7ff0 ("bpf: add bpf_skb_change_proto helper") Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In event of failure during register_netdevice, free_netdev is
invoked immediately. free_netdev assumes that all the netdevice
refcounts have been dropped prior to it being called and as a
result frees and clears out the refcount pointer.
However, this is not necessarily true as some of the operations
in the NETDEV_UNREGISTER notifier handlers queue RCU callbacks for
invocation after a grace period. The IPv4 callback in_dev_rcu_put
tries to access the refcount after free_netdev is called which
leads to a null de-reference-
The ixgbevf driver currently does IPsec Tx offloading
based on an existing secpath. However, the secpath
can also come from the Rx side, in this case it is
misinterpreted for Tx offload and the packets are
dropped with a "bad sa_idx" error. Fix this by using
the xfrm_offload() function to test for Tx offload.
CC: Shannon Nelson <snelson@pensando.io> Fixes: 7f68d4306701 ("ixgbevf: enable VF IPsec offload operations") Reported-by: Jonathan Tooker <jonathan@reliablehosting.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ixgbe driver currently does IPsec TX offloading
based on an existing secpath. However, the secpath
can also come from the RX side, in this case it is
misinterpreted for TX offload and the packets are
dropped with a "bad sa_idx" error. Fix this by using
the xfrm_offload() function to test for TX offload.
Fixes: 592594704761 ("ixgbe: process the Tx ipsec offload") Reported-by: Michael Marley <michael@michaelmarley.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that capi_write() is reading past the end of the message.
Fix it by checking the message's length in the needed places.
Reported-and-tested-by: syzbot+0849c524d9c634f5ae66@syzkaller.appspotmail.com Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Mediatek based smartphone owner reports problems with USB
tethering in Linux. The verbose USB listing shows a rndis_host
interface pair (e0/01/03 + 10/00/00), but the driver fails to
bind with
[ 355.960428] usb 1-4: bad CDC descriptors
The problem is a failsafe test intended to filter out ACM serial
functions using the same 02/02/ff class/subclass/protocol as RNDIS.
The serial functions are recognized by their non-zero bmCapabilities.
No RNDIS function with non-zero bmCapabilities were known at the time
this failsafe was added. But it turns out that some Wireless class
RNDIS functions are using the bmCapabilities field. These functions
are uniquely identified as RNDIS by their class/subclass/protocol, so
the failing test can safely be disabled. The same applies to the two
types of Misc class RNDIS functions.
Applying the failsafe to Communication class functions only retains
the original functionality, and fixes the problem for the Mediatek based
smartphone.
Tow examples of CDC functional descriptors with non-zero bmCapabilities
from Wireless class RNDIS functions are:
0e8d:000a Mediatek Crosscall Spider X5 3G Phone
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x0f
connection notifications
sends break
line coding and serial state
get/set/clear comm features
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
and
19d2:1023 ZTE K4201-z
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC Union:
bMasterInterface 0
bSlaveInterface 1
The Mediatek example is believed to apply to most smartphones with
Mediatek firmware. The ZTE example is most likely also part of a larger
family of devices/firmwares.
Suggested-by: Lars Melin <larsm17@gmail.com> Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent at the end.
In fact, NLMSG_DONE is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: 949f1e39a617 ("bridge: mdb: notify on router port add and del") CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code assumes log_num < in_num everywhere, and that is true as long as
in_num is incremented by descriptor iov count, and log_num by 1. However
this breaks if there's a zero sized descriptor.
As a result, if a malicious guest creates a vring desc with desc.len = 0,
it may cause the host kernel to crash by overflowing the log array. This
bug can be triggered during the VM migration.
There's no need to log when desc.len = 0, so just don't increment log_num
in this case.
Fixes: 3a4d5c94e959 ("vhost_net: a kernel-level virtio server") Cc: stable@vger.kernel.org Reviewed-by: Lidong Chen <lidongchen@tencent.com> Signed-off-by: ruippan <ruippan@tencent.com> Signed-off-by: yongduan <yongduan@tencent.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lock_extent_buffer_io() returns 1 to the caller to tell it everything
went fine and the callers needs to start writeback for the extent buffer
(submit a bio, etc), 0 to tell the caller everything went fine but it does
not need to start writeback for the extent buffer, and a negative value if
some error happened.
When it's about to return 1 it tries to lock all pages, and if a try lock
on a page fails, and we didn't flush any existing bio in our "epd", it
calls flush_write_bio(epd) and overwrites the return value of 1 to 0 or
an error. The page might have been locked elsewhere, not with the goal
of starting writeback of the extent buffer, and even by some code other
than btrfs, like page migration for example, so it does not mean the
writeback of the extent buffer was already started by some other task,
so returning a 0 tells the caller (btree_write_cache_pages()) to not
start writeback for the extent buffer. Note that epd might currently have
either no bio, so flush_write_bio() returns 0 (success) or it might have
a bio for another extent buffer with a lower index (logical address).
Since we return 0 with the EXTENT_BUFFER_WRITEBACK bit set on the
extent buffer and writeback is never started for the extent buffer,
future attempts to writeback the extent buffer will hang forever waiting
on that bit to be cleared, since it can only be cleared after writeback
completes. Such hang is reported with a trace like the following:
So fix this by not overwriting the return value (ret) with the result
from flush_write_bio(). We also need to clear the EXTENT_BUFFER_WRITEBACK
bit in case flush_write_bio() returns an error, otherwise it will hang
any future attempts to writeback the extent buffer, and undo all work
done before (set back EXTENT_BUFFER_DIRTY, etc).
This is a regression introduced in the 5.2 kernel.
The same tests failing on CFL+ platforms are also failing on ICL.
Documentation doesn't list the
WaAllowPMDepthAndInvocationCountAccessFromUMD workaround for ICL but
applying it fixes the same tests as CFL.
v2: Use only one whitelist entry (Lionel)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Tested-by: Anuj Phogat <anuj.phogat@gmail.com> Cc: stable@vger.kernel.org # 6883eab27481: drm/i915: Support flags in whitlist WAs Cc: stable@vger.kernel.org Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190628120720.21682-4-lionel.g.landwerlin@intel.com
(cherry picked from commit 3fe0107e45ab396342497e06b8924cdd485cde3b) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bspec: 14091 Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Cc: stable@vger.kernel.org # 6883eab27481: drm/i915: Support flags in whitlist WAs Cc: stable@vger.kernel.org Acked-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20190628120720.21682-3-lionel.g.landwerlin@intel.com
(cherry picked from commit 2c903da50f5a9522b134e488bd0f92646c46f3c0) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The access to airq_areas was racy ever since the adapter interrupts got
introduced to virtio-ccw, but since commit 39c7dcb15892 ("virtio/s390:
make airq summary indicators DMA") this became an issue in practice as
well. Namely before that commit the airq_info that got overwritten was
still functional. After that commit however the two infos share a
summary_indicator, which aggravates the situation. Which means
auto-online mechanism occasionally hangs the boot with virtio_blk.
André Draszik [Sat, 10 Aug 2019 15:07:58 +0000 (16:07 +0100)]
usb: chipidea: imx: fix EPROBE_DEFER support during driver probe
If driver probe needs to be deferred, e.g. because ci_hdrc_add_device()
isn't ready yet, this driver currently misbehaves badly:
a) success is still reported to the driver core (meaning a 2nd
probe attempt will never be done), leaving the driver in
a dysfunctional state and the hardware unusable
c) the error path in combination with driver removal causes
imbalanced calls to the clk_*() and pm_()* APIs
a) happens because the original intended return value is
overwritten (with 0) by the return code of
regulator_disable() in ci_hdrc_imx_probe()'s error path
b) happens because ci_pdev is -EPROBE_DEFER, which causes
ci_hdrc_remove_device() to OOPS
Fix a) by being more careful in ci_hdrc_imx_probe()'s error
path and not overwriting the real error code
Fix b) by calling the respective cleanup functions during
remove only when needed (when ci_pdev != NULL, i.e. when
everything was initialised correctly). This also has the
side effect of not causing imbalanced clk_*() and pm_*()
API calls as part of the error code path.
Peter Chen [Sun, 28 Apr 2019 02:35:31 +0000 (10:35 +0800)]
usb: chipidea: imx: add imx7ulp support
In this commit, we add CI_HDRC_PMQOS to avoid system entering idle,
at imx7ulp, if the system enters idle, the DMA will stop, so the USB
transfer can't work at this case.
The SD host controller specification defines 3 types software reset:
software reset for data line, software reset for command line and software
reset for all. Software reset for all means this reset affects the entire
Host controller except for the card detection circuit.
In sdhci_runtime_resume_host() we always do a software "reset for all",
which causes the Spreadtrum variant controller to work abnormally after
resuming. To fix the problem, let's do a software reset for the data and
the command part, rather than "for all".
However, as sdhci_runtime_resume() is a common sdhci function and we don't
want to change the behaviour for other variants, let's introduce a new
in-parameter for it. This enables the caller to decide if a "reset for all"
shall be done or not.
On VLV/CHV there is some kind of linkage between the cdclk frequency
and the DP link frequency. The spec says:
"For DP audio configuration, cdclk frequency shall be set to
meet the following requirements:
DP Link Frequency(MHz) | Cdclk frequency(MHz)
270 | 320 or higher
162 | 200 or higher"
I suspect that would more accurately be expressed as
"cdclk >= DP link clock", and in any case we can express it like
that in the code because of the limited set of cdclk (200, 266,
320, 400 MHz) and link frequencies (162 and 270 MHz) we support.
Without this we can end up in a situation where the cdclk
is too low and enabling DP audio will kill the pipe. Happens
eg. with 2560x1440 modes where the 266MHz cdclk is sufficient
to pump the pixels (241.5 MHz dotclock) but is too low for
the DP audio due to the link frequency being 270 MHz.
v2: Spell out the cdclk and link frequencies we actually support
The Demand Prefetch workaround (binding table prefetching) only applies
to Icelake A0/B0. But the Sampler Prefetch workaround needs to be
applied to all Gen11 steppings, according to a programming note in the
SARCHKMD documentation.
Using the Intel Gallium driver, I have seen intermittent failures in
the dEQP-GLES31.functional.copy_image.non_compressed.* tests. After
applying this workaround, the tests reliably pass.
projects / linux-stable / log