* The 'Rx tried to sub from different maps, paths, or prohibited types'
is reworked into more specific/differentiated error messages for better
guidance.
* The change into 'value -4294967168 makes map_value pointer be out of
bounds' is due to moving the mixed bounds check into the speculation
handling and thus occuring slightly later than above mentioned sanity
check.
* The change into 'math between map_value pointer and register with
unbounded min value' is similarly due to register sanity check coming
before the mixed bounds check.
* The case of 'map access: known scalar += value_ptr from different maps'
now loads fine given masks are the same from the different paths (despite
max map value size being different).
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon - skip bounds.c test mods, they won't change error msg on 5.4] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This work tightens the offset mask we use for unprivileged pointer arithmetic
in order to mitigate a corner case reported by Piotr and Benedict where in
the speculative domain it is possible to advance, for example, the map value
pointer by up to value_size-1 out-of-bounds in order to leak kernel memory
via side-channel to user space.
Before this change, the computed ptr_limit for retrieve_ptr_limit() helper
represents largest valid distance when moving pointer to the right or left
which is then fed as aux->alu_limit to generate masking instructions against
the offset register. After the change, the derived aux->alu_limit represents
the largest potential value of the offset register which we mask against which
is just a narrower subset of the former limit.
For minimal complexity, we call sanitize_ptr_alu() from 2 observation points
in adjust_ptr_min_max_vals(), that is, before and after the simulated alu
operation. In the first step, we retieve the alu_state and alu_limit before
the operation as well as we branch-off a verifier path and push it to the
verification stack as we did before which checks the dst_reg under truncation,
in other words, when the speculative domain would attempt to move the pointer
out-of-bounds.
In the second step, we retrieve the new alu_limit and calculate the absolute
distance between both. Moreover, we commit the alu_state and final alu_limit
via update_alu_sanitation_state() to the env's instruction aux data, and bail
out from there if there is a mismatch due to coming from different verification
paths with different states.
Reported-by: Piotr Krysiuk <piotras@gmail.com> Reported-by: Benedict Schlueter <benedict.schlueter@rub.de> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Tested-by: Benedict Schlueter <benedict.schlueter@rub.de>
[fllinden@amazon.com: backported to 5.4] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a small sanitize_needed() helper function and move sanitize_val_alu()
out of the main opcode switch. In upcoming work, we'll move sanitize_ptr_alu()
as well out of its opcode switch so this helps to streamline both.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: backported to 5.4] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the bounds check in adjust_ptr_min_max_vals() into a small helper named
sanitize_check_bounds() in order to simplify the former a bit.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: backport to 5.4] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Consolidate all error handling and provide more user-friendly error messages
from sanitize_ptr_alu() and sanitize_val_alu().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: backport to 5.4] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mixed signed bounds check really belongs into retrieve_ptr_limit()
instead of outside of it in adjust_ptr_min_max_vals(). The reason is
that this check is not tied to PTR_TO_MAP_VALUE only, but to all pointer
types that we handle in retrieve_ptr_limit() and given errors from the latter
propagate back to adjust_ptr_min_max_vals() and lead to rejection of the
program, it's a better place to reside to avoid anything slipping through
for future types. The reason why we must reject such off_reg is that we
otherwise would not be able to derive a mask, see details in 9d7eceede769
("bpf: restrict unknown scalars of mixed signed bounds for unprivileged").
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Acked-by: Alexei Starovoitov <ast@kernel.org>
[fllinden@amazon.com: backport to 5.4] Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
suspend() does its poisoning conditionally, resume() does it
unconditionally. On a device with combined interfaces this
will balance, on a device with two interfaces the counter will
go negative and resubmission will fail.
Both actions need to be done conditionally.
Fixes: 6069e3e927c8f ("USB: cdc-acm: untangle a circular dependency between callback and softint") Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210421074513.4327-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8a12f8836145 ("net: hso: fix null-ptr-deref during tty device
unregistration") fixed the racy minor allocation reported by syzbot, but
introduced an unconditional NULL-pointer dereference on every disconnect
instead.
Specifically, the serial device table must no longer be accessed after
the minor has been released by hso_serial_tty_unregister().
Fixes: 8a12f8836145 ("net: hso: fix null-ptr-deref during tty device unregistration") Cc: stable@vger.kernel.org Cc: Anirudh Rayabharam <mail@anirudhrb.com> Reported-by: Leonardo Antoniazzi <leoanto@aruba.it> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Anirudh Rayabharam <mail@anirudhrb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit in Fixes: added support for kexec-ing a kernel on panic using a
new system call. As part of it, it does prepare a memory map for the new
kernel.
However, while doing so, it wrongly accesses memory it has not
allocated: it accesses the first element of the cmem->ranges[] array in
memmap_exclude_ranges() but it has not allocated the memory for it in
crash_setup_memmap_entries(). As KASAN reports:
BUG: KASAN: vmalloc-out-of-bounds in crash_setup_memmap_entries+0x17e/0x3a0
Write of size 8 at addr ffffc90000426008 by task kexec/1187
(gdb) list *crash_setup_memmap_entries+0x17e
0xffffffff8107cafe is in crash_setup_memmap_entries (arch/x86/kernel/crash.c:322).
317 unsigned long long mend)
318 {
319 unsigned long start, end;
320
321 cmem->ranges[0].start = mstart;
322 cmem->ranges[0].end = mend;
323 cmem->nr_ranges = 1;
324
325 /* Exclude elf header region */
326 start = image->arch.elf_load_addr;
(gdb)
Make sure the ranges array becomes a single element allocated.
[ bp: Write a proper commit message. ]
Fixes: dd5f726076cc ("kexec: support for kexec on panic using new system call") Signed-off-by: Mike Galbraith <efault@gmx.de> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Dave Young <dyoung@redhat.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/725fa3dc1da2737f0f6188a1a9701bead257ea9d.camel@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ia64_mf() macro defined in tools/arch/ia64/include/asm/barrier.h is
already defined in <asm/gcc_intrin.h> on ia64 which causes libbpf
failing to build:
CC /usr/src/linux/tools/bpf/bpftool//libbpf/staticobjs/libbpf.o
In file included from /usr/src/linux/tools/include/asm/barrier.h:24,
from /usr/src/linux/tools/include/linux/ring_buffer.h:4,
from libbpf.c:37:
/usr/src/linux/tools/include/asm/../../arch/ia64/include/asm/barrier.h:43: error: "ia64_mf" redefined [-Werror]
43 | #define ia64_mf() asm volatile ("mf" ::: "memory")
|
In file included from /usr/include/ia64-linux-gnu/asm/intrinsics.h:20,
from /usr/include/ia64-linux-gnu/asm/swab.h:11,
from /usr/include/linux/swab.h:8,
from /usr/include/linux/byteorder/little_endian.h:13,
from /usr/include/ia64-linux-gnu/asm/byteorder.h:5,
from /usr/src/linux/tools/include/uapi/linux/perf_event.h:20,
from libbpf.c:36:
/usr/include/ia64-linux-gnu/asm/gcc_intrin.h:382: note: this is the location of the previous definition
382 | #define ia64_mf() __asm__ volatile ("mf" ::: "memory")
|
cc1: all warnings being treated as errors
Thus, remove the definition from tools/arch/ia64/include/asm/barrier.h.
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_SPARSEMEM=y and CONFIG_MEMORY_HOTPLUG=y, the functions
computer_pernodesize() and scatter_node_data() should not be marked as
__meminit because they are needed after init, on any memory hotplug
event. Also, early_nr_cpus_node() is called by compute_pernodesize(),
so early_nr_cpus_node() cannot be __meminit either.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1612): Section mismatch in reference from the function arch_alloc_nodedata() to the function .meminit.text:compute_pernodesize()
The function arch_alloc_nodedata() references the function __meminit compute_pernodesize().
This is often because arch_alloc_nodedata lacks a __meminit annotation or the annotation of compute_pernodesize is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1692): Section mismatch in reference from the function arch_refresh_nodedata() to the function .meminit.text:scatter_node_data()
The function arch_refresh_nodedata() references the function __meminit scatter_node_data().
This is often because arch_refresh_nodedata lacks a __meminit annotation or the annotation of scatter_node_data is wrong.
WARNING: modpost: vmlinux.o(.text.unlikely+0x1502): Section mismatch in reference from the function compute_pernodesize() to the function .meminit.text:early_nr_cpus_node()
The function compute_pernodesize() references the function __meminit early_nr_cpus_node().
This is often because compute_pernodesize lacks a __meminit annotation or the annotation of early_nr_cpus_node is wrong.
Link: https://lkml.kernel.org/r/20210411001201.3069-1-rdunlap@infradead.org Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Mike Rapoport <rppt@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
e1000's #define of CONFIG_RAM_BASE conflicts with a Kconfig symbol in
arch/csky/Kconfig.
The symbol in e1000 has been around longer, so change arch/csky/ to use
DRAM_BASE instead of RAM_BASE to remove the conflict. (although e1000
is also a 2-line change)
The logic in connect() is currently written with the assumption that
xenbus_watch_pathfmt() will return an error for a node that does not
exist. This assumption is incorrect: xenstore does allow a watch to
be registered for a nonexistent node (and will send notifications
should the node be subsequently created).
As of commit 1f2565780 ("xen-netback: remove 'hotplug-status' once it
has served its purpose"), this leads to a failure when a domU
transitions into XenbusStateConnected more than once. On the first
domU transition into Connected state, the "hotplug-status" node will
be deleted by the hotplug_status_changed() callback in dom0. On the
second or subsequent domU transition into Connected state, the
hotplug_status_changed() callback will therefore never be invoked, and
so the backend will remain stuck in InitWait.
This failure prevents scenarios such as reloading the xen-netfront
module within a domU, or booting a domU via iPXE. There is
unfortunately no way for the domU to work around this dom0 bug.
Fix by explicitly checking for existence of the "hotplug-status" node,
thereby creating the behaviour that was previously assumed to exist.
Signed-off-by: Michael Brown <mbrown@fensystems.co.uk> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently psw_idle does not allocate a stack frame and does not
save its r14 and r15 into the save area. Even though this is valid from
call ABI point of view, because psw_idle does not make any calls
explicitly, in reality psw_idle is an entry point for controlled
transition into serving interrupts. So, in practice, psw_idle stack
frame is analyzed during stack unwinding. Depending on build options
that r14 slot in the save area of psw_idle might either contain a value
saved by previous sibling call or complete garbage.
Check within geneve_xmit_skb/geneve6_xmit_skb that sk_buff structure
is large enough to include IPv4 or IPv6 header, and reject if not. The
geneve_xmit_skb portion and overall idea was contributed by Eric Dumazet.
Fixes a KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=abe95dc3e3e9667fc23b8d81f29ecad95c6f106f
Suggested-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+2e406a9ac75bb71d4b7a@syzkaller.appspotmail.com Signed-off-by: Phillip Potter <phil@philpotter.co.uk> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Also some omap3 devices like n900 seem to have eMMC and micro-sd swapped
around with commit 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for
drivers that existed in v4.4").
Let's fix the issue with aliases as discussed on the mailing lists. While
the mmc aliases should be board specific, let's first fix the issue with
minimal changes.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the function auxtrace_parse_snapshot_options(), the callback pointer
"itr->parse_snapshot_options" can be NULL if it has not been set during
the AUX record initialization. This can cause tool crashing if the
callback pointer "itr->parse_snapshot_options" is dereferenced without
performing NULL check.
Add a NULL check for the pointer "itr->parse_snapshot_options" before
invoke the callback.
Fixes: d20031bb63dd6dde ("perf tools: Add AUX area tracing Snapshot Mode") Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Tiezhu Yang <yangtiezhu@loongson.cn> Link: http://lore.kernel.org/lkml/20210420151554.2031768-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The only stepping of Broadwell Xeon parts is stepping 1. Fix the
relevant isolation_ucodes[] entry, which previously enumerated
stepping 2.
Although the original commit was characterized as an optimization, it
is also a workaround for a correctness issue.
If a PMI arrives between kvm's call to perf_guest_get_msrs() and the
subsequent VM-entry, a stale value for the IA32_PEBS_ENABLE MSR may be
restored at the next VM-exit. This is because, unbeknownst to kvm, PMI
throttling may clear bits in the IA32_PEBS_ENABLE MSR. CPUs with "PEBS
isolation" don't suffer from this issue, because perf_guest_get_msrs()
doesn't report the IA32_PEBS_ENABLE value.
Fixes: 9b545c04abd4f ("perf/x86/kvm: Avoid unnecessary work in guest filtering") Signed-off-by: Jim Mattson <jmattson@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Peter Shier <pshier@google.com> Acked-by: Andi Kleen <ak@linux.intel.com> Link: https://lkml.kernel.org/r/20210422001834.1748319-1-jmattson@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There may be a kernel panic on the Haswell server and the Broadwell
server, if the snbep_pci2phy_map_init() return error.
The uncore_extra_pci_dev[HSWEP_PCI_PCU_3] is used in the cpu_init() to
detect the existence of the SBOX, which is a MSR type of PMON unit.
The uncore_extra_pci_dev is allocated in the uncore_pci_init(). If the
snbep_pci2phy_map_init() returns error, perf doesn't initialize the
PCI type of the PMON units, so the uncore_extra_pci_dev will not be
allocated. But perf may continue initializing the MSR type of PMON
units. A null dereference kernel panic will be triggered.
The sockets in a Haswell server or a Broadwell server are identical.
Only need to detect the existence of the SBOX once.
Current perf probes all available PCU devices and stores them into the
uncore_extra_pci_dev. It's unnecessary.
Use the pci_get_device() to replace the uncore_extra_pci_dev. Only
detect the existence of the SBOX on the first available PCU device once.
Factor out hswep_has_limit_sbox(), since the Haswell server and the
Broadwell server uses the same way to detect the existence of the SBOX.
Add some macros to replace the magic number.
Fixes: 5306c31c5733 ("perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes") Reported-by: Steve Wahl <steve.wahl@hpe.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Steve Wahl <steve.wahl@hpe.com> Link: https://lkml.kernel.org/r/1618521764-100923-1-git-send-email-kan.liang@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
While this code is executed with the wait_lock held, a reader can
acquire the lock without holding wait_lock. The writer side loops
checking the value with the atomic_cond_read_acquire(), but only truly
acquires the lock when the compare-and-exchange is completed
successfully which isn’t ordered. This exposes the window between the
acquire and the cmpxchg to an A-B-A problem which allows reads
following the lock acquisition to observe values speculatively before
the write lock is truly acquired.
We've seen a problem in epoll where the reader does a xchg while
holding the read lock, but the writer can see a value change out from
under it.
A core can order the read of the ovflist ahead of the
atomic_cmpxchg_relaxed(). Switching the cmpxchg to use acquire
semantics addresses this issue at which point the atomic_cond_read can
be switched to use relaxed semantics.
Fixes: b519b56e378ee ("locking/qrwlock: Use atomic_cond_read_acquire() when spinning in qrwlock") Signed-off-by: Ali Saidi <alisaidi@amazon.com>
[peterz: use try_cmpxchg()] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Steve Capper <steve.capper@arm.com> Acked-by: Will Deacon <will@kernel.org> Acked-by: Waiman Long <longman@redhat.com> Tested-by: Steve Capper <steve.capper@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 941432d00768 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.
This was based on the observation that the Pine64-LTS has as "push-push"
SD card socket, and that the schematic mentions the card detect GPIO.
After having received two reports about failing SD card access with that
patch, some more research and polls on that subject revealed that there
are at least two different versions of the Pine64-LTS out there:
- On some boards (including mine) the card detect pin is "stuck" at
high, regardless of an microSD card being inserted or not.
- On other boards the card-detect is working, but is active-high, by
virtue of an explicit inverter circuit, as shown in the schematic.
To cover all versions of the board out there, and don't take any chances,
let's revert the introduction of the active-low CD GPIO, but let's use
the broken-cd property for the Pine64-LTS this time. That should avoid
regressions and should work for everyone, even allowing SD card changes
now.
The SOPine card detect has proven to be working, so let's keep that
GPIO in place.
Fixes: 941432d00768 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card") Reported-by: Michael Weiser <michael.weiser@gmx.de> Reported-by: Daniel Kulesz <kuleszdl@posteo.org> Suggested-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Michael Weiser <michael.weiser@gmx.de> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20210414104740.31497-1-andre.przywara@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
As we are using cpu_pm to save and restore context, we must also save and
restore the GPIO sysconfig register. This is needed because we are not
calling PM runtime functions at all with cpu_pm.
We need to save the sysconfig on idle as it's value can get reconfigured by
PM runtime and can be different from the init time value. Device specific
flags like "ti,no-idle-on-init" can affect the init value.
Fixes: b764a5863fd8 ("gpio: omap: Remove custom PM calls and use cpu_pm instead") Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Adam Ford <aford173@gmail.com> Cc: Andreas Kemnade <andreas@kemnade.info> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current code returns the syscall number which an invalid
syscall number is supplied and tracing is enabled. This makes
the strace testsuite fail.
Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1895132
[krzysztof: adjusted the backport around missing ifdef CONFIG_SECCOMP,
add Link and Fixes; apparently this should go with the referenced commit] Fixes: 00332c16b160 ("s390/ptrace: pass invalid syscall numbers to tracing") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit fee2d546414d ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
Since uprobes is not supported for thumb, check that the thumb bit is
not set when matching the uprobes instruction hooks.
The Arm UDF instructions used for uprobes triggering
(UPROBE_SWBP_ARM_INSN and UPROBE_SS_ARM_INSN) coincidentally share the
same encoding as a pair of unallocated 32-bit thumb instructions (not
UDF) when the condition code is 0b1111 (0xf). This in effect makes it
possible to trigger the uprobes functionality from thumb, and at that
using two unallocated instructions which are not permanently undefined.
Signed-off-by: Fredrik Strupe <fredrik@strupe.net> Cc: stable@vger.kernel.org Fixes: c7edc9e326d5 ("ARM: add uprobes support") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been reported [0] that using pause frames in jumbo mode impacts
performance. There's no available chip documentation, but vendor
drivers r8168 and r8125 don't advertise pause in jumbo mode. So let's
do the same, according to Roman it fixes the issue.
Fixes: 9cf9b84cc701 ("r8169: make use of phy_set_asym_pause") Reported-by: Roman Mamedov <rm+bko@romanrm.net> Tested-by: Roman Mamedov <rm+bko@romanrm.net> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Merge enabling and disabling jumbo packets to one function to make
the code a little simpler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d365498 ("r8169: remove fiddling with the PCIe max read request size") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
r8168b_0_hw_jumbo_enable() and r8168b_0_hw_jumbo_disable() both do the
same and just set PCI_EXP_DEVCTL_NOSNOOP_EN. We can simplify the code
by moving this setting for RTL8168B to rtl_hw_start_8168().
The attempt to improve performance by changing the PCIe max read request
size was added in the vendor driver more than 10 years back and copied
to r8169 driver. In the vendor driver this has been removed long ago.
Obviously it had no effect, also in my tests I didn't see any
difference. Typically the max payload size is less than 512 bytes
anyway, and the PCI core takes care that the maximum supported value
is set. So let's remove fiddling with PCIe max read request size from
r8169 too.
Commit 941432d00768 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.
However while both boards indeed have a working CD GPIO on PF6, the
polarity is different: the SOPine modules uses a "push-pull" socket,
which has an active-high switch, while the Pine64-LTS use the more
traditional push-push socket and the common active-low switch.
Fix the polarity in the sopine.dtsi, and overwrite it in the LTS
board .dts, to make the SD card work again on systems using SOPine
modules.
Fixes: 941432d00768 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card") Reported-by: Ashley <contact@victorianfox.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20210316144219.5973-1-andre.przywara@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 30fdfb929e82 ("PCI: Add a call to pci_assign_irq() in
pci_device_probe()"), the PCI code will call the IRQ mapping function
whenever a PCI driver is probed. If these are marked as __init, this
causes an oops if a PCI driver is loaded or bound after the kernel has
initialised.
Fixes: 30fdfb929e82 ("PCI: Add a call to pci_assign_irq() in pci_device_probe()") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 0f6925b3e8da ("virtio_net: Do not pull payload in skb->head")
Guenter Roeck reported one failure in his tests using sh architecture.
After much debugging, we have been able to spot silent unaligned accesses
in inet_gro_receive()
The issue at hand is that upper networking stacks assume their header
is word-aligned. Low level drivers are supposed to reserve NET_IP_ALIGN
bytes before the Ethernet header to make that happen.
This patch hardens skb_gro_reset_offset() to not allow frag0 fast-path
if the fragment is not properly aligned.
Some arches like x86, arm64 and powerpc do not care and define NET_IP_ALIGN
as 0, this extra check will be a NOP for them.
Note that if frag0 is not used, GRO will call pskb_may_pull()
as many times as needed to pull network and transport headers.
Fixes: 0f6925b3e8da ("virtio_net: Do not pull payload in skb->head") Fixes: 78a478d0efd9 ("gro: Inline skb_gro_header and cache frag0 virtual address") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Cc: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the unnecessary napi_schedule() call in __ibmvnic_open() since
interrupt_rx() calls napi_schedule_prep/__napi_schedule during every
receive interrupt.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling") Signed-off-by: Lijun Pan <lijunp213@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During adapter reset, do_reset/do_hard_reset calls ibmvnic_open(),
which will calls napi_schedule if previous state is VNIC_CLOSED
(i.e, the reset case, and "ifconfig down" case). So there is no need
for do_reset to call napi_schedule again at the end of the function
though napi_schedule will neglect the request if napi is already
scheduled.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling") Signed-off-by: Lijun Pan <lijunp213@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__ibmvnic_open calls napi_disable without checking whether NAPI polling
has already been disabled or not. This could cause napi_disable
being called twice, which could generate deadlock. For example,
the first napi_disable will spin until NAPI_STATE_SCHED is cleared
by napi_complete_done, then set it again.
When napi_disable is called the second time, it will loop infinitely
because no dev->poll will be running to clear NAPI_STATE_SCHED.
To prevent above scenario from happening, call ibmvnic_napi_disable()
which checks if napi is disabled or not before calling napi_disable.
Fixes: bfc32f297337 ("ibmvnic: Move resource initialization to its own routine") Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by: Lijun Pan <lijunp213@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix this panic by adding more rules to calculate the value of @rss_size_max
which could be used in allocating the queues when bpf is loaded, which,
however, could cause the failure and then trigger the NULL pointer of
vsi->rx_rings. Prio to this fix, the machine doesn't care about how many
cpus are online and then allocates 256 queues on the machine with 32 cpus
online actually.
Once the load of bpf begins, the log will go like this "failed to get
tracking for 256 queues for VSI 0 err -12" and this "setup of MAIN VSI
failed".
Thus, I attach the key information of the crash-log here.
A sit interface created without a local or a remote address is linked
into the `sit_net::tunnels_wc` list of its original namespace. When
deleting a network namespace, delete the devices that have been moved.
The following script triggers a null pointer dereference if devices
linked in a deleted `sit_net` remain:
for i in `seq 1 30`; do
ip netns add ns-test
ip netns exec ns-test ip link add dev veth0 type veth peer veth1
ip netns exec ns-test ip link add dev sit$i type sit dev veth0
ip netns exec ns-test ip link set dev sit$i netns $$
ip netns del ns-test
done
for i in `seq 1 30`; do
ip link del dev sit$i
done
Fixes: 5e6700b3bf98f ("sit: add support of x-netns") Signed-off-by: Hristo Venev <hristo@venev.name> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the probe fails, we must disable the regulator that was previously
enabled.
This patch is a follow-up to commit ac88c531a5b3
("net: davicom: Fix regulator not turned off on failed probe") which missed
one case.
Fixes: 7994fe55a4a2 ("dm9000: Add regulator and reset support to dm9000") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
introduces the restore of CMP registers on resume path. In case the IP
doesn't support type 2 screeners (zero on DCFG8 register) the
struct macb::rx_fs_list::list is not initialized and thus the
list_for_each_entry(item, &bp->rx_fs_list.list, list) loop introduced in
commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
will access an uninitialized list leading to crash. Thus, initialize
the struct macb::rx_fs_list::list without taking into account if the
IP supports type 2 screeners or not.
Fixes: a14d273ba159 ("net: macb: restore cmp registers on resume path") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Same problem that also existed in iptables/ip(6)tables, when
arptable_filter is removed there is no longer a wait period before the
table/ruleset is free'd.
Unregister the hook in pre_exit, then remove the table in the exit
function.
This used to work correctly because the old nf_hook_unregister API
did unconditional synchronize_net.
The per-net hook unregister function uses call_rcu instead.
Just like ip/ip6/arptables, the hooks have to be removed, then
synchronize_rcu() has to be called to make sure no more packets are being
processed before the ruleset data is released.
Place the hook unregistration in the pre_exit hook, then call the new
ebtables pre_exit function from there.
Years ago, when first netns support got added for netfilter+ebtables,
this used an older (now removed) netfilter hook unregister API, that did
a unconditional synchronize_rcu().
Now that all is done with call_rcu, ebtable_{filter,nat,broute} pernet exit
handlers may free the ebtable ruleset while packets are still in flight.
This can only happens on module removal, not during netns exit.
The new function expects the table name, not the table struct.
This is because upcoming patch set (targeting -next) will remove all
net->xt.{nat,filter,broute}_table instances, this makes it necessary
to avoid external references to those member variables.
The existing APIs will be converted, so follow the upcoming scheme of
passing name + hook type instead.
In case a platform doesn't provide explicit flush-hints but provides an
explicit flush callback via ND_REGION_ASYNC region flag, then
nvdimm_has_flush() still returns '0' indicating that writes do not
require flushing. This happens on PPC64 with patch at [1] applied, where
'deep_flush' of a region was denied even though an explicit flush
function was provided.
Fix this by adding a condition to nvdimm_has_flush() to test for the
ND_REGION_ASYNC flag on the region and see if a 'region->flush' callback
is assigned.
When the cache_type for the SCSI device is changed, the SCSI layer issues a
MODE_SELECT command. The caching mode details are communicated via a
request buffer associated with the SCSI command with data direction set as
DMA_TO_DEVICE (scsi_mode_select()). When this command reaches the libata
layer, as a part of generic initial setup, libata layer sets up the
scatterlist for the command using the SCSI command (ata_scsi_qc_new()).
This command is then translated by the libata layer into
ATA_CMD_SET_FEATURES (ata_scsi_mode_select_xlat()). The libata layer treats
this as a non-data command (ata_mselect_caching()), since it only needs an
ATA taskfile to pass the caching on/off information to the device. It does
not need the scatterlist that has been setup, so it does not perform
dma_map_sg() on the scatterlist (ata_qc_issue()). Unfortunately, when this
command reaches the libsas layer (sas_ata_qc_issue()), libsas layer sees it
as a non-data command with a scatterlist. It cannot extract the correct DMA
length since the scatterlist has not been mapped with dma_map_sg() for a
DMA operation. When this partially constructed SAS task reaches pm80xx
LLDD, it results in the following warning:
"pm80xx_chip_sata_req 6058: The sg list address
start_addr=0x0000000000000000 data_len=0x0end_addr_high=0xffffffff
end_addr_low=0xffffffff has crossed 4G boundary"
Update libsas to handle ATA non-data commands separately so num_scatter and
total_xfer_len remain 0.
Link: https://lore.kernel.org/r/20210318225632.2481291-1-jollys@google.com Fixes: 53de092f47ff ("scsi: libsas: Set data_dir as DMA_NONE if libata marks qc as NODATA") Tested-by: Luo Jiaxing <luojiaxing@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Jolly Shah <jollys@google.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The root cause is LLVM's assembler has a one-pass design, meaning it
cannot figure out these instruction lengths when the .org directive is
outside of the subsection that they are in, which was changed by the
.arch_extension directive added in the above commit.
Apply the same fix from commit 966a0acce2fc ("arm64/alternatives: move
length validation inside the subsection") to the alternative_endif
macro, shuffling the .org directives so that the length validation
happen will always happen in the same subsections. alternative_insn has
not shown any issue yet but it appears that it could have the same issue
in the future so just preemptively change it.
Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences") Cc: <stable@vger.kernel.org> # 5.8.x Link: https://github.com/ClangBuiltLinux/linux/issues/1347 Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20210414000803.662534-1-nathan@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inline asm's addr operand is marked as input-only, however in
the case where an exception is taken it may be modified by the BIC
instruction on the exception path. Fix the problem by using a temporary
register as the destination register for the BIC instruction.
This does the directory entry name verification for the legacy
"fillonedir" (and compat) interface that goes all the way back to the
dark ages before we had a proper dirent, and the readdir() system call
returned just a single entry at a time.
Nobody should use this interface unless you still have binaries from
1991, but let's do it right.
This came up during discussions about unsafe_copy_to_user() and proper
checking of all the inputs to it, as the networking layer is looking to
use it in a few new places. So let's make sure the _old_ users do it
all right and proper, before we add new ones.
See also commit 8a23eb804ca4 ("Make filldir[64]() verify the directory
entry filename is valid") which did the proper modern interfaces that
people actually use. It had a note:
Note that I didn't bother adding the checks to any legacy interfaces
that nobody uses.
which this now corrects. Note that we really don't care about POSIX and
the presense of '/' in a directory entry, but verify_dirent_name() also
ends up doing the proper name length verification which is what the
input checking discussion was about.
[ Another option would be to remove the support for this particular very
old interface: any binaries that use it are likely a.out binaries, and
they will no longer run anyway since we removed a.out binftm support
in commit eac616557050 ("x86: Deprecate a.out support").
But I'm not sure which came first: getdents() or ELF support, so let's
pretend somebody might still have a working binary that uses the
legacy readdir() case.. ]
commit df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to
block size") introduced the possibility for misaligned roots IO
relative to the underlying device's logical block size. E.g. Android's
default RS roots=2 results in dm_bufio->block_size=1024, which causes
the following EIO if the logical block size of the device is 4096,
given v->data_dev_block_bits=12:
E sd 0 : 0:0:0: [sda] tag#30 request not aligned to the logical block size
E blk_update_request: I/O error, dev sda, sector 10368424 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
E device-mapper: verity-fec: 254:8: FEC 9244672: parity read failed (block 18056): -5
Fix this by onlu using f->roots for dm_bufio blocksize IFF it is
aligned to v->data_dev_block_bits.
Fixes: df7b59ba9245 ("dm verity: fix FEC for RS roots unaligned to block size") Cc: stable@vger.kernel.org Signed-off-by: Jaegeuk Kim <jaegeuk@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Valid HID_GENERIC type of devices set EV_KEY and EV_ABS by wacom_map_usage.
When *_input_capabilities are reached, those devices should already have
their proper EV_* set. EV_KEY and EV_ABS only need to be set for
non-HID_GENERIC type of devices in *_input_capabilities.
Devices that don't support HID descitoprs will pass back to hid-input for
registration without being accidentally rejected by the introduction of
patch: "Input: refuse to register absolute devices without absinfo"
Fixes: 6ecfe51b4082 ("Input: refuse to register absolute devices without absinfo") Signed-off-by: Ping Cheng <ping.cheng@wacom.com> Reviewed-by: Jason Gerecke <Jason.Gerecke@wacom.com> Tested-by: Juan Garrido <Juan.Garrido@wacom.com> CC: stable@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Zenbook Flip entry that was added overwrites a previous one
because of a typo:
In file included from drivers/input/serio/i8042.h:23,
from drivers/input/serio/i8042.c:131:
drivers/input/serio/i8042-x86ia64io.h:591:28: error: initialized field overwritten [-Werror=override-init]
591 | .matches = {
| ^
drivers/input/serio/i8042-x86ia64io.h:591:28: note: (near initialization for 'i8042_dmi_noselftest_table[0].matches')
Add the missing separator between the two.
Fixes: b5d6e7ab7fe7 ("Input: i8042 - add ASUS Zenbook Flip to noselftest list") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Marcos Paulo de Souza <mpdesouza@suse.com> Link: https://lore.kernel.org/r/20210323130623.2302402-1-arnd@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bytes 2 and 1 need to be shifted left by 4 bits, the least significant
nibble of each is stored in byte 3. Currently they are only
being shifted by 3 causing the reported coordinates to be incorrect.
This matches downstream examples, and has been confirmed on my
device (OnePlus 7 Pro).
Fixes: 0145a7141e59 ("Input: add support for the Samsung S6SY761 touchscreen") Signed-off-by: Caleb Connolly <caleb@connolly.tech> Reviewed-by: Andi Shyti <andi@etezian.org> Link: https://lore.kernel.org/r/20210305185710.225168-1-caleb@connolly.tech Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cfg80211_inform_bss expects to receive a TSF value, but is given the
time since boot in nanoseconds. TSF values are expected to be at
microsecond scale rather than nanosecond scale.
In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.
Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.
[ 239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 239.449531] pgd = 80204000
...
[ 239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[ 239.481591] Hardware name: Generic DT based system
[ 239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[ 239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[ 239.497823] LR is at 0xbe08fc54
...
[ 239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[ 239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[ 239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[ 239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
0211])
[ 239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[ 239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[ 239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
)
[ 239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[ 239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[ 239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[ 239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[ 239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[ 239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)
pci_resource_start() is not a good indicator to determine if a PCI
resource exists or not, since the resource may start at address 0.
This is seen when trying to instantiate the driver in qemu for riscv32
or riscv64.
This patch forbids to add llsec seclevel for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
This patch stops dumping llsec seclevels for monitors which we don't
support yet. Otherwise we will access llsec mib which isn't initialized
for monitors.
This patch forbids to del llsec devkey for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
This patch forbids to add llsec devkey for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
This patch stops dumping llsec devkeys for monitors which we don't support
yet. Otherwise we will access llsec mib which isn't initialized for
monitors.
This patch forbids to del llsec dev for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
This patch forbids to add llsec dev for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
This patch forbids to del llsec key for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
This patch forbids to add llsec key for monitor interfaces which we
don't support yet. Otherwise we will access llsec mib which isn't
initialized for monitors.
rport_dev_loss_timedout() sets the rport state to SRP_PORT_LOST and the
SCSI target state to SDEV_TRANSPORT_OFFLINE. If this races with
srp_reconnect_work(), a warning is printed:
Mar 27 18:48:07 ictm1604s01h4 kernel: dev_loss_tmo expired for SRP port-18:1 / host18.
Mar 27 18:48:07 ictm1604s01h4 kernel: ------------[ cut here ]------------
Mar 27 18:48:07 ictm1604s01h4 kernel: scsi_internal_device_block(18:0:0:100) failed: ret = -22
Mar 27 18:48:07 ictm1604s01h4 kernel: Call Trace:
Mar 27 18:48:07 ictm1604s01h4 kernel: ? scsi_target_unblock+0x50/0x50 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel: starget_for_each_device+0x80/0xb0 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel: target_block+0x24/0x30 [scsi_mod]
Mar 27 18:48:07 ictm1604s01h4 kernel: device_for_each_child+0x57/0x90
Mar 27 18:48:07 ictm1604s01h4 kernel: srp_reconnect_rport+0xe4/0x230 [scsi_transport_srp]
Mar 27 18:48:07 ictm1604s01h4 kernel: srp_reconnect_work+0x40/0xc0 [scsi_transport_srp]
Avoid this by not trying to block targets for rports in SRP_PORT_LOST
state.
Link: https://lore.kernel.org/r/20210401091105.8046-1-mwilck@suse.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin Wilck <mwilck@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using the driver in I2S TDM mode, the fsl_esai_startup()
function rewrites the number of slots previously set by the
fsl_esai_set_dai_tdm_slot() function to 2.
To fix this, let's use the saved slot count value or, if TDM
is not used and the number of slots is not set, the driver will use
the default value (2), which is set by fsl_esai_probe().
Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Acked-by: Nicolin Chen <nicoleotsuka@gmail.com> Link: https://lore.kernel.org/r/20210402081405.9892-1-shc_work@mail.ru Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
They were reading a counter that was configured to ALWAYS_COUNT (ie.
cycles that the GPU is doing something) rather than ALWAYS_ON. This
isn't the thing that userspace is looking for.
Signed-off-by: Rob Clark <robdclark@chromium.org> Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Message-Id: <20210325012358.1759770-2-robdclark@gmail.com> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The clang integrated assembler fails to build one file with
a complex asm instruction:
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: error: invalid instruction, any one of the following would fix this:
mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
^
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: note: instruction requires: armv6t2
mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
^
arch/arm/mach-omap1/ams-delta-fiq-handler.S:249:2: note: instruction requires: thumb2
mov r10, #(1 << (((NR_IRQS_LEGACY + 12) - NR_IRQS_LEGACY) % 32)) @ set deferred_fiq bit
^
The problem is that 'NR_IRQS_LEGACY' is not defined here. Apparently
gas does not care because we first add and then subtract this number,
leading to the immediate value to be the same regardless of the
specific definition of NR_IRQS_LEGACY.
Neither the way that 'gas' just silently builds this file, nor the
way that clang IAS makes nonsensical suggestions for how to fix it
is great. Fortunately there is an easy fix, which is to #include
the header that contains the definition.
clang warns about an impossible condition when building with 32-bit
phys_addr_t:
arch/arm/mach-keystone/keystone.c:79:16: error: result of comparison of constant 51539607551 with expression of type 'phys_addr_t' (aka 'unsigned int') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
mem_end > KEYSTONE_HIGH_PHYS_END) {
~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~
arch/arm/mach-keystone/keystone.c:78:16: error: result of comparison of constant 34359738368 with expression of type 'phys_addr_t' (aka 'unsigned int') is always true [-Werror,-Wtautological-constant-out-of-range-compare]
if (mem_start < KEYSTONE_HIGH_PHYS_START ||
~~~~~~~~~ ^ ~~~~~~~~~~~~~~~~~~~~~~~~
Change the temporary variable to a fixed-size u64 to avoid the warning.
After a short network outage, the dst_entry is timed out and put
in DST_OBSOLETE_DEAD. We are in this code because arp reply comes
from this neighbour after network recovers. There is a potential
race condition that dst_entry is still in DST_OBSOLETE_DEAD.
With that, another neighbour lookup causes more harm than good.
In best case all packets in arp_queue are lost. This is
counterproductive to the original goal of finding a better path
for those packets.
I observed a worst case with 4.x kernel where a dst_entry in
DST_OBSOLETE_DEAD state is associated with loopback net_device.
It leads to an ethernet header with all zero addresses.
A packet with all zero source MAC address is quite deadly with
mac80211, ath9k and 802.11 block ack. It fails
ieee80211_find_sta_by_ifaddr in ath9k (xmit.c). Ath9k flushes tx
queue (ath_tx_complete_aggr). BAW (block ack window) is not
updated. BAW logic is damaged and ath9k transmission is disabled.
Signed-off-by: Tong Zhu <zhutong@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since this message is printed when dynamically allocated spinlocks (e.g.
kzalloc()) are used without initialization (e.g. spin_lock_init()),
suggest to developers to check whether initialization functions for objects
were called, before making developers wonder what annotation is missing.
Fix moving mmc devices with dts aliases as discussed on the lists.
Without this we now have internal eMMC mmc1 show up as mmc2 compared
to the earlier order of devices.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We have a duplicate legacy clock defined for sha2md5_fck that can
sometimes race with clk_disable() with the dts configured clock
for OMAP4_SHA2MD5_CLKCTRL when unused clocks are disabled during
boot causing an "Unhandled fault: imprecise external abort".
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver registers an interrupt handler in _probe, but didn't configure
them until later when the _open function is called. In between, the keypad
can fire an IRQ due to touchpad activity, which the handler ignores. This
causes the kernel to disable the interrupt, blocking the keypad from
working.
Fix this by disabling interrupts before registering the handler.
Additionally, disable them in _close, so that they're only enabled while
open.
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
The bug is fixed by acquiring addr_wq_lock in sctp_destroy_sock
instead of sctp_close.
This addresses CVE-2021-23133.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Fixes: 610236587600 ("bpf: Add new cgroup attach type to enable sock modifications") Signed-off-by: Or Cohen <orcohen@paloaltonetworks.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On timeout, SRB pointer was cleared from outstanding command array and
dropped. It was not allowed to go through the done process and cleanup.
This patch will abort the SRB where FW will return it with an error status
and resume the normal cleanup.
Link: https://lore.kernel.org/r/20191217220617.28084-3-hmadhani@marvell.com Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Session is stuck if driver sees FW has received a PRLI. Driver allows FW to
finish with processing of PRLI by checking back with FW at a later time to
see if the PRLI has finished. Instead, driver failed to push forward after
re-checking PRLI completion.
Current code will send PRLI with FC-NVMe bit set for the targets which
support only FCP. This may result into issue with targets which do not
understand NVMe and will go into a strange state. This patch would restart
the login process by going back to PLOGI state. The PLOGI state will force
the target to respond to correct PRLI request.
Fixes: c76ae845ea836 ("scsi: qla2xxx: Add error handling for PLOGI ELS passthrough") Cc: stable@vger.kernel.org # 5.4 Link: https://lore.kernel.org/r/20191105150657.8092-2-hmadhani@marvell.com Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Quinn Tran <qutran@marvell.com> Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log