commit 66c705d07d784 ("SoC: rsnd: add interrupt support for SSI BUSIF
buffer") adds __rsnd_ssi_interrupt() checks for BUSIF status,
but is using "break" at for loop.
This means it is not checking all status. Let's check all BUSIF status.
Fixes: commit 66c705d07d784 ("SoC: rsnd: add interrupt support for SSI BUSIF buffer") Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/874kgh1jsw.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not call nvme_configure_apst when the controller is not live, given
that nvme_configure_apst will fail due the lack of an admin queue when
the controller is being torn down and nvme_set_latency_tolerance is
called from dev_pm_qos_hide_latency_tolerance.
Fixes: 510a405d945b("nvme: fix memory leak for power latency tolerance") Reported-by: Peng Liu <liupeng17@lenovo.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This clock must be always enabled to allow access to any registers in
fsys1 CMU. Until proper solution based on runtime PM is applied
(similar to what was done for Exynos5433), mark that clock as critical
so it won't be disabled.
It was observed on Samsung Galaxy S6 device (based on Exynos7420), where
UFS module is probed before pmic used to power that device.
In this case defer probe was happening and that clock was disabled by
UFS driver, causing whole boot to hang on next CMU access.
Fixes: 753195a749a6 ("clk: samsung: exynos7: Correct CMU_FSYS1 clocks names") Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/linux-clk/20201024154346.9589-1-pawel.mikolaj.chmiel@gmail.com
[s.nawrocki: Added comment in the code] Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These sysctls point to global variables:
- NF_SYSCTL_CT_MAX (&nf_conntrack_max)
- NF_SYSCTL_CT_EXPECT_MAX (&nf_ct_expect_max)
- NF_SYSCTL_CT_BUCKETS (&nf_conntrack_htable_size_user)
Because their data pointers are not updated to point to per-netns
structures, they must be marked read-only in a non-init_net ns.
Otherwise, changes in any net namespace are reflected in (leaked into)
all other net namespaces. This problem has existed since the
introduction of net namespaces.
The current logic marks them read-only only if the net namespace is
owned by an unprivileged user (other than init_user_ns).
Commit d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in
unprivileged namespaces") "exposes all sysctls even if the namespace is
unpriviliged." Since we need to mark them readonly in any case, we can
forego the unprivileged user check altogether.
Fixes: d0febd81ae77 ("netfilter: conntrack: re-visit sysctls in unprivileged namespaces") Signed-off-by: Jonathon Reinhart <Jonathon.Reinhart@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot can trigger the WARN() in init_uevent_argv() which isn't the
nicest as the code does properly recover and handle the error. So
change the WARN() call to pr_warn() and provide some more information on
what the buffer size that was needed.
"usb: typec: tcpm: Address incorrect values of tcpm psy for pps supply"
introduced a regression for req_out_volt and req_op_curr calculation.
req_out_volt should consider the newly calculated max voltage instead
of previously accepted max voltage by the port partner. Likewise,
req_op_curr should consider the newly calculated max current instead
of previously accepted max current by the port partner.
The early ATAGS/DT mapping code uses SECTION_SHIFT to mask low order
bits of R2, and decides that no ATAGS/DTB were provided if the resulting
value is 0x0.
This means that on systems where DRAM starts at 0x0 (such as Raspberry
Pi), no explicit mapping of the DT will be created if R2 points into the
first 1 MB section of memory. This was not a problem before, because the
decompressed kernel is loaded at the base of DRAM and mapped using
sections as well, and so as long as the DT is referenced via a virtual
address that uses the same translation (the linear map, in this case),
things work fine.
However, commit 7a1be318f579 ("9012/1: move device tree mapping out of
linear region") changes this, and now the DT is referenced via a virtual
address that is disjoint from the linear mapping of DRAM, and so we need
the early code to create the DT mapping unconditionally.
So let's create the early DT mapping for any value of R2 != 0x0.
149a3ffe62b9dbc3 ("9012/1: move device tree mapping out of linear region")
created a permanent, read-only section mapping of the device tree blob
provided by the firmware, and added a set of macros to get the base and
size of the virtually mapped FDT based on the physical address. However,
while the mapping code uses the SECTION_SIZE macro correctly, the macros
use PMD_SIZE instead, which means something entirely different on ARM when
using short descriptors, and is therefore not the right quantity to use
here. So replace PMD_SIZE with SECTION_SIZE. While at it, change the names
of the macro and its parameter to clarify that it returns the virtual
address of the start of the FDT, based on the physical address in memory.
Tested-by: Joel Stanley <joel@jms.id.au> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ARM, setting up the linear region is tricky, given the constraints
around placement and alignment of the memblocks, and how the kernel
itself as well as the DT are placed in physical memory.
Let's simplify matters a bit, by moving the device tree mapping to the
top of the address space, right between the end of the vmalloc region
and the start of the the fixmap region, and create a read-only mapping
for it that is independent of the size of the linear region, and how it
is organized.
Since this region was formerly used as a guard region, which will now be
populated fully on LPAE builds by this read-only mapping (which will
still be able to function as a guard region for stray writes), bump the
start of the [underutilized] fixmap region by 512 KB as well, to ensure
that there is always a proper guard region here. Doing so still leaves
ample room for the fixmap space, even with NR_CPUS set to its maximum
value of 32.
Tested-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before moving the DT mapping out of the linear region, let's prepare
for this change by removing all the phys-to-virt translations of the
__atags_pointer variable, and perform this translation only once at
setup time.
Tested-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
f2fs didn't properly clean up if verity failed to be enabled on a file:
- It left verity metadata (pages past EOF) in the page cache, which
would be exposed to userspace if the file was later extended.
- It didn't truncate the verity metadata at all (either from cache or
from disk) if an error occurred while setting the verity bit.
Fix these bugs by adding a call to truncate_inode_pages() and ensuring
that we truncate the verity metadata (both from cache and from disk) in
all error paths. Also rework the code to cleanly separate the success
path from the error paths, which makes it much easier to understand.
Finally, log a message if f2fs_truncate() fails, since it might
otherwise fail silently.
Reported-by: Yunlei He <heyunlei@hihonor.com> Fixes: 95ae251fe828 ("f2fs: add fs-verity support") Cc: <stable@vger.kernel.org> # v5.4+ Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tz->lock must be hold during the looping over the instances in that
thermal zone. This lock was missing in the governor code since the
beginning, so it's hard to point into a particular commit.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210422153624.6074-2-lukasz.luba@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the inline asm with a DIVU instruction from `__div64_32' and use
plain C code for the intended DIVMOD calculation instead. GCC is smart
enough to know that both the quotient and the remainder are calculated
with single DIVU, so with ISAs up to R5 the same instruction is actually
produced with overall similar code.
For R6 compiled code will work, but separate DIVU and MODU instructions
will be produced, which are also interlocked, so scalar implementations
will likely not perform as well as older ISAs with their asynchronous MD
unit. Likely still faster then the generic algorithm though.
This removes a compilation error for R6 however where the original DIVU
instruction is not supported anymore and the MDU accumulator registers
have been removed and consequently GCC complains as to a constraint it
cannot find a register for:
In file included from ./include/linux/math.h:5,
from ./include/linux/kernel.h:13,
from mm/page-writeback.c:15:
./include/linux/math64.h: In function 'div_u64_rem':
./arch/mips/include/asm/div64.h:76:17: error: inconsistent operand constraints in an 'asm'
76 | __asm__("divu $0, %z1, %z2" \
| ^~~~~~~
./include/asm-generic/div64.h:245:25: note: in expansion of macro '__div64_32'
245 | __rem = __div64_32(&(n), __base); \
| ^~~~~~~~~~
./include/linux/math64.h:91:22: note: in expansion of macro 'do_div'
91 | *remainder = do_div(dividend, divisor);
| ^~~~~~
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0404s from 1.0445s with R3400
@40MHz. The module's MIPS I machine code has also shrunk by 12 bytes or
3 instructions.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already check the high part of the divident against zero to avoid the
costly DIVU instruction in that case, needed to reduce the high part of
the divident, so we may well check against the divisor instead and set
the high part of the quotient to zero right away. We need to treat the
high part the divident in that case though as the remainder that would
be calculated by the DIVU instruction we avoided.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0445s and 0.2619s from 1.0668s
and 0.2629s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our current MIPS platform `__div64_32' handler is inactive, because it
is incorrectly only enabled for 64-bit configurations, for which generic
`do_div' code does not call it anyway.
The handler is not suitable for being called from there though as it
only calculates 32 bits of the quotient under the assumption the 64-bit
divident has been suitably reduced. Code for such reduction used to be
there, however it has been incorrectly removed with commit c21004cd5b4c
("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0."), which should
have only updated an obsoleted constraint for an inline asm involving
$hi and $lo register outputs, while possibly wiring the original MIPS
variant of the `do_div' macro as `__div64_32' handler for the generic
`do_div' implementation
Correct the handler as follows then:
- Revert most of the commit referred, however retaining the current
formatting, except for the final two instructions of the inline asm
sequence, which the original commit missed. Omit the original 64-bit
parts though.
- Rename the original `do_div' macro to `__div64_32'. Use the combined
`x' constraint referring to the MD accumulator as a whole, replacing
the original individual `h' and `l' constraints used for $hi and $lo
registers respectively, of which `h' has been obsoleted with GCC 4.4.
Update surrounding code accordingly.
We have since removed support for GCC versions before 4.9, so no need
for a special arrangement here; GCC has supported the `x' constraint
since forever anyway, or at least going back to 1991.
- Rename the `__base' local variable in `__div64_32' to `__radix' to
avoid a conflict with a local variable in `do_div'.
- Actually enable this code for 32-bit rather than 64-bit configurations
by qualifying it with BITS_PER_LONG being 32 instead of 64. Include
<asm/bitsperlong.h> for this macro rather than <linux/types.h> as we
don't need anything else.
- Finally include <asm-generic/div64.h> last rather than first.
This has passed correctness verification with test_div64 and reduced the
module's average execution time down to 1.0668s and 0.2629s from 2.1529s
and 0.5647s respectively for an R3400 CPU @40MHz and a 5Kc CPU @160MHz.
For a reference 64-bit `do_div' code where we have the DDIVU instruction
available to do the whole calculation right away averages at 0.0660s for
the latter CPU.
Fixes: c21004cd5b4c ("MIPS: Rewrite <asm/div64.h> to work with gcc 4.4.0.") Reported-by: Huacai Chen <chenhuacai@kernel.org> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable@vger.kernel.org # v2.6.30+ Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.
The default kernel configuration choice for the defxx driver is the use
of I/O ports rather than MMIO for PCI and EISA systems. It may have
made sense as a conservative backwards compatible choice back when MMIO
operation support was added to the driver as a part of TURBOchannel bus
support. However nowadays this configuration choice makes the driver
unusable with systems that do not implement I/O transactions for PCIe.
Make DEFXX_MMIO the configuration default then, except where configured
for EISA. This exception is because an EISA adapter can have its MMIO
decoding disabled with ECU (EISA Configuration Utility) and therefore
not available with the resource allocation infrastructure we implement,
while port I/O is always readily available as it uses slot-specific
addressing, directly mapped to the slot an option card has been placed
in and handled with our EISA bus support core. Conversely a kernel that
supports modern systems which may not have I/O transactions implemented
for PCIe will usually not be expected to handle legacy EISA systems.
The change of the default will make it easier for people, including but
not limited to distribution packagers, to make a working choice for the
driver.
Update the option description accordingly and while at it replace the
potentially ambiguous PIO acronym with IOP for "port I/O" vs "I/O ports"
according to our nomenclature used elsewhere.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: e89a2cfb7d7b ("[TC] defxx: TURBOchannel support") Cc: stable@vger.kernel.org # v2.6.21+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
32-bit architectures which expect 8-byte alignment for 8-byte integers and
need 64-bit DMA addresses (arm, mips, ppc) had their struct page
inadvertently expanded in 2019. When the dma_addr_t was added, it forced
the alignment of the union to 8 bytes, which inserted a 4 byte gap between
'flags' and the union.
Fix this by storing the dma_addr_t in one or two adjacent unsigned longs.
This restores the alignment to that of an unsigned long. We always
store the low bits in the first word to prevent the PageTail bit from
being inadvertently set on a big endian platform. If that happened,
get_user_pages_fast() racing against a page which was freed and
reallocated to the page_pool could dereference a bogus compound_head(),
which would be hard to trace back to this cause.
We have a cycle of callbacks scheduling works which submit
URBs with those callbacks. This needs to be blocked, stopped
and unblocked to untangle the circle.
The raw temperature value is a 16-bit signed integer. The sign casting
is missing in the code, which results in a wrong temperature reported
by userspace tools, fix it.
Cc: stable@vger.kernel.org Fixes: 3904b28efb2c ("iio: gyro: Add driver for the MPU-3050 gyroscope")
Datasheet: https://www.cdiweb.com/datasheets/invensense/mpu-3000a.pdf Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Asus TF201 Reported-by: Svyatoslav Ryhel <clamor95@gmail.com> Reviewed-by: Andy Shevchenko <Andy.Shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Link: https://lore.kernel.org/r/20210423020959.5023-1-digetx@gmail.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of AMD xhci controller require reset on resume.
Occasionally AMD xhci controller does not respond to
Stop endpoint command.
Once the issue happens controller goes into bad state
and in that case controller needs to be reset.
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring") Cc: <stable@vger.kernel.org> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an error is received when issuing a start or update transfer
command, the error handler will stop all active requests (including
the current USB request), and call dwc3_gadget_giveback() to notify
function drivers of the requests which have been stopped. Avoid
returning an error for kick transfer during EP queue, to remove
duplicate cleanup operations on the request being queued.
This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcdf6 ("usb: dwc2: gadget: manage ep0 state in software") Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Phil Elwell <phil@raspberrypi.com> Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some devices (specifically the SC8180x based Surface Pro X with
QCOM04A6) HC halt / xhci_halt() times out during boot. Manually binding
the xhci-hcd driver at some point later does not exhibit this behavior.
To work around this, double XHCI_MAX_HALT_USEC, which also resolves this
issue.
When extcon is used in combination with dwc3, it is assumed that the dwc3
registers are untouched and as such are only configured if VBUS is valid
or ID is tied to ground.
In case VBUS is not valid or ID is floating, the registers are not
configured as such during driver initialization, causing a wrong
default state during boot.
If the registers are not in a default state, because they are for
instance touched by a boot loader, this can cause for a kernel error.
bio completions can race when a page spans more than one file system
block. Add a spinlock to synchronize marking the page uptodate.
Fixes: 9dc55f1389f9 ("iomap: add support for sub-pagesize buffered I/O without buffer heads") Reported-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a tag set is shared across request queues (e.g. SCSI LUNs) then the
block layer core keeps track of the number of active request queues in
tags->active_queues. blk_mq_tag_busy() and blk_mq_tag_idle() update that
atomic counter if the hctx flag BLK_MQ_F_TAG_QUEUE_SHARED is set. Make
sure that blk_mq_exit_queue() calls blk_mq_tag_idle() before that flag is
cleared by blk_mq_del_queue_tag_set().
Cc: Christoph Hellwig <hch@infradead.org> Cc: Ming Lei <ming.lei@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Fixes: 0d2602ca30e4 ("blk-mq: improve support for shared tags maps") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20210513171529.7977-1-bvanassche@acm.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Open /dev/nbdX first, the config_refs will be 1 and
the pointers in nbd_device are still null. Disconnect
/dev/nbdX, then reference a null recv_workq. The
protection by config_refs in nbd_genl_disconnect is useless.
To fix it, just add if (nbd->recv_workq) to nbd_disconnect_and_put().
Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs") Signed-off-by: Sun Ke <sunke32@huawei.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Link: https://lore.kernel.org/r/20210512114331.1233964-2-sunke32@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
__blk_mq_sched_bio_merge() gets the ctx and hctx for the current CPU and
passes the hctx to ->bio_merge(). kyber_bio_merge() then gets the ctx
for the current CPU again and uses that to get the corresponding Kyber
context in the passed hctx. However, the thread may be preempted between
the two calls to blk_mq_get_ctx(), and the ctx returned the second time
may no longer correspond to the passed hctx. This "works" accidentally
most of the time, but it can cause us to read garbage if the second ctx
came from an hctx with more ctx's than the first one (i.e., if
ctx->index_hw[hctx->type] > hctx->nr_ctx).
This manifested as this UBSAN array index out of bounds error reported
by Jakub:
UBSAN: array-index-out-of-bounds in ../kernel/locking/qspinlock.c:130:9
index 13106 is out of range for type 'long unsigned int [128]'
Call Trace:
dump_stack+0xa4/0xe5
ubsan_epilogue+0x5/0x40
__ubsan_handle_out_of_bounds.cold.13+0x2a/0x34
queued_spin_lock_slowpath+0x476/0x480
do_raw_spin_lock+0x1c2/0x1d0
kyber_bio_merge+0x112/0x180
blk_mq_submit_bio+0x1f5/0x1100
submit_bio_noacct+0x7b0/0x870
submit_bio+0xc2/0x3a0
btrfs_map_bio+0x4f0/0x9d0
btrfs_submit_data_bio+0x24e/0x310
submit_one_bio+0x7f/0xb0
submit_extent_page+0xc4/0x440
__extent_writepage_io+0x2b8/0x5e0
__extent_writepage+0x28d/0x6e0
extent_write_cache_pages+0x4d7/0x7a0
extent_writepages+0xa2/0x110
do_writepages+0x8f/0x180
__writeback_single_inode+0x99/0x7f0
writeback_sb_inodes+0x34e/0x790
__writeback_inodes_wb+0x9e/0x120
wb_writeback+0x4d2/0x660
wb_workfn+0x64d/0xa10
process_one_work+0x53a/0xa80
worker_thread+0x69/0x5b0
kthread+0x20b/0x240
ret_from_fork+0x1f/0x30
Only Kyber uses the hctx, so fix it by passing the request_queue to
->bio_merge() instead. BFQ and mq-deadline just use that, and Kyber can
map the queues itself to avoid the mismatch.
If 'acpi_device_set_name()' fails, we must free
'acpi_device_bus_id->bus_id' or there is a (potential) memory leak.
Fixes: eb50aaf960e3 ("ACPI: scan: Use unique number for instance_no") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The poll rate limiter time was initialized at zero. This breaks the
comparison in time_after if jiffies is large. Switch to storing the
next update time rather than the previous time, and initialize the
time when the device is probed.
Fixes: c10e753d43eb ("hwmon (occ): Add sensor types and versions") Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20210429151336.18980-1-eajames@linux.ibm.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
'retval' is known to be -ENODEV here.
This is a hard-coded default error code which is not useful in the error
message. Moreover, another error message is printed at the end of the
error handling path. The corresponding error code (-ENOMEM) is more
informative.
So remove simplify the first error message.
While at it, also remove the useless initialization of 'retval'.
Gen2 tiles are 2KiB in size so i915_gem_object_get_tile_row_size()
can in fact return <4KiB, which leads to div-by-zero here.
Avoid that.
Not sure i915_gem_object_get_tile_row_size() is entirely
sane anyway since it doesn't account for the different tile
layouts on i8xx/i915...
I'm not able to hit this before commit 6846895fde05 ("drm/i915:
Replace PIN_NONFAULT with calls to PIN_NOEVICT") and it looks
like I also need to run recent version of Mesa. With those in
place xonotic trips on this quite easily on my 85x.
Screen flickers rapidly when two 4K 60Hz monitors are in use. This issue
doesn't happen when one monitor is 4K 60Hz (pixelclock 594MHz) and
another one is 4K 30Hz (pixelclock 297MHz).
The issue is gone after setting "power_dpm_force_performance_level" to
"high". Following the indication, we found that the issue occurs when
sclk is too low.
So resolve the issue by disabling sclk switching when there are two
monitors requires high pixelclock (> 297MHz).
v2:
- Only apply the fix to Oland. Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch series "mm/hugetlb: Fix issues on file sealing and fork", v2.
Hugh reported issue with F_SEAL_FUTURE_WRITE not applied correctly to
hugetlbfs, which I can easily verify using the memfd_test program, which
seems that the program is hardly run with hugetlbfs pages (as by default
shmem).
Meanwhile I found another probably even more severe issue on that hugetlb
fork won't wr-protect child cow pages, so child can potentially write to
parent private pages. Patch 2 addresses that.
After this series applied, "memfd_test hugetlbfs" should start to pass.
This patch (of 2):
F_SEAL_FUTURE_WRITE is missing for hugetlb starting from the first day.
There is a test program for that and it fails constantly.
1. Userspace issues a UFFD ioctl, which ends up calling into
shmem_mfill_atomic_pte(). We successfully account the blocks, we
shmem_alloc_page(), but then the copy_from_user() fails. We return
-ENOENT. We don't release the page we allocated.
2. Our caller detects this error code, tries the copy_from_user() after
dropping the mmap_lock, and retries, calling back into
shmem_mfill_atomic_pte().
3. Meanwhile, let's say another process filled up the tmpfs being used.
4. So shmem_mfill_atomic_pte() fails to account blocks this time, and
immediately returns - without releasing the page.
This triggers a BUG_ON in our caller, which asserts that the page
should always be consumed, unless -ENOENT is returned.
To fix this, detect if we have such a "dangling" page when accounting
fails, and if so, release it before returning.
Link: https://lkml.kernel.org/r/20210428230858.348400-1-axelrasmussen@google.com Fixes: cb658a453b93 ("userfaultfd: shmem: avoid leaking blocks and used blocks in UFFDIO_COPY") Signed-off-by: Axel Rasmussen <axelrasmussen@google.com> Reported-by: Hugh Dickins <hughd@google.com> Acked-by: Hugh Dickins <hughd@google.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sysbot has reported a "divide error" which has been identified as being
caused by a corrupted file_size value within the file inode. This value
has been corrupted to a much larger value than expected.
Calculate_skip() is passed i_size_read(inode) >> msblk->block_log. Due to
the file_size value corruption this overflows the int argument/variable in
that function, leading to the divide error.
This patch changes the function to use u64. This will accommodate any
unexpectedly large values due to corruption.
The value returned from calculate_skip() is clamped to be never more than
SQUASHFS_CACHED_BLKS - 1, or 7. So file_size corruption does not lead to
an unexpectedly large return result here.
I believe there are some issues introduced by commit 31651c607151
("hfsplus: avoid deadlock on file truncation")
HFS+ has extent records which always contains 8 extents. In case the
first extent record in catalog file gets full, new ones are allocated from
extents overflow file.
In case shrinking truncate happens to middle of an extent record which
locates in extents overflow file, the logic in hfsplus_file_truncate() was
changed so that call to hfs_brec_remove() is not guarded any more.
Right action would be just freeing the extents that exceed the new size
inside extent record by calling hfsplus_free_extents(), and then check if
the whole extent record should be removed. However since the guard
(blk_cnt > start) is now after the call to hfs_brec_remove(), this has
unfortunate effect that the last matching extent record is removed
unconditionally.
To reproduce this issue, create a file which has at least 10 extents, and
then perform shrinking truncate into middle of the last extent record, so
that the number of remaining extents is not under or divisible by 8. This
causes the last extent record (8 extents) to be removed totally instead of
truncating into middle of it. Thus this causes corruption, and lost data.
Fix for this is simply checking if the new truncated end is below the
start of this extent record, making it safe to remove the full extent
record. However call to hfs_brec_remove() can't be moved to it's previous
place since we're dropping ->tree_lock and it can cause a race condition
and the cached info being invalidated possibly corrupting the node data.
Another issue is related to this one. When entering into the block
(blk_cnt > start) we are not holding the ->tree_lock. We break out from
the loop not holding the lock, but hfs_find_exit() does unlock it. Not
sure if it's possible for someone else to take the lock under our feet,
but it can cause hard to debug errors and premature unlocking. Even if
there's no real risk of it, the locking should still always be kept in
balance. Thus taking the lock now just before the check.
The entry flush mitigation can be enabled/disabled at runtime via a
debugfs file (entry_flush), which causes the kernel to patch itself to
enable/disable the relevant mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
Shows that we returned to userspace with a corrupted LR that points into
the kernel, due to executing the partially patched call to the fallback
entry flush (ie. we missed the LR restore).
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
The STF (store-to-load forwarding) barrier mitigation can be
enabled/disabled at runtime via a debugfs file (stf_barrier), which
causes the kernel to patch itself to enable/disable the relevant
mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
Shows that we returned to userspace without restoring the user r13
value, due to executing the partially patched STF exit code.
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
Fixes: a048a07d7f45 ("powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit") Cc: stable@vger.kernel.org # v4.17+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210506044959.1298123-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
32-bit PAGE_MASK can not be used as a mask for physical addresses
when PAE is enabled. PAGE_MASK_PHYS must be used for physical
addresses instead of PAGE_MASK.
Without this, init gets SIGSEGV if pte_modify was called:
| potentially unexpected fatal signal 11.
| Path: /bin/busybox
| CPU: 0 PID: 1 Comm: init Not tainted 5.12.0-rc5-00003-g1e43c377a79f-dirty
| Insn could not be fetched
| @No matching VMA found
| ECR: 0x00040000 EFA: 0x00000000 ERET: 0x00000000
| STAT: 0x80080082 [IE U ] BTA: 0x00000000
| SP: 0x5f9ffe44 FP: 0x00000000 BLK: 0xaf3d4
| LPS: 0x000d093e LPE: 0x000d0950 LPC: 0x00000000
| r00: 0x00000002 r01: 0x5f9fff14 r02: 0x5f9fff20
| ...
| Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
We have NR_syscall syscalls from [0 .. NR_syscall-1].
However the check for invalid syscall number is "> NR_syscall" as
opposed to >=. This off-by-one error erronesously allows "NR_syscall"
to be treated as valid syscall causeing out-of-bounds access into
syscall-call table ensuing a crash (holes within syscall table have a
invalid-entry handler but this is beyond the array implementing the
table).
This problem showed up on v5.6 kernel when testing glibc 2.33 (v5.10
kernel capable, includng faccessat2 syscall 439). The v5.6 kernel has
NR_syscalls=439 (0 to 438). Due to the bug, 439 passed by glibc was
not handled as -ENOSYS but processed leading to a crash.
Unlike other supported adapters, 2.5G and 5G use different
PHY type identifiers for reading/writing PHY settings
and for reading link status. This commit introduces
separate PHY identifiers for these two operation types.
Fixes: 2e45d3f4677a ("i40e: Add support for X710 B/P & SFP+ cards") Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When FEC mode was changed the link didn't know it because
the link was not reset and new parameters were not negotiated.
Set a flag 'I40E_AQ_PHY_ENABLE_ATOMIC_LINK' in 'abilities'
to restart the link and make it run with the new settings.
Fixes: 1d96340196f1 ("i40e: Add support FEC configuration for Fortville 25G") Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the call to i40e_client_del_instance frees the object
pf->cinst, however pf->cinst->lan_info is being accessed after
the free. Fix this by adding the missing return.
Addresses-Coverity: ("Read from pointer after free") Fixes: 7b0b1a6d0ac9 ("i40e: Disable iWARP VSI PETCP_ENA flag on netdev down events") Signed-off-by: Yunjian Wang <wangyunjian@huawei.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When vzalloc() returns NULL to sha_regions, no error return code of
kexec_calculate_store_digests() is assigned. To fix this bug, ret is
assigned with -ENOMEM in this case.
Link: https://lkml.kernel.org/r/20210309083904.24321-1-baijiaju1990@gmail.com Fixes: a43cac0d9dc2 ("kexec: split kexec_file syscall code to kexec_file.c") Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Acked-by: Baoquan He <bhe@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes an issue where old load on a cfs_rq is not properly decayed,
resulting in strange behavior where fairness can decrease drastically.
Real workloads with equally weighted control groups have ended up
getting a respective 99% and 1%(!!) of cpu time.
When an idle task is attached to a cfs_rq by attaching a pid to a cgroup,
the old load of the task is attached to the new cfs_rq and sched_entity by
attach_entity_cfs_rq. If the task is then moved to another cpu (and
therefore cfs_rq) before being enqueued/woken up, the load will be moved
to cfs_rq->removed from the sched_entity. Such a move will happen when
enforcing a cpuset on the task (eg. via a cgroup) that force it to move.
The load will however not be removed from the task_group itself, making
it look like there is a constant load on that cfs_rq. This causes the
vruntime of tasks on other sibling cfs_rq's to increase faster than they
are supposed to; causing severe fairness issues. If no other task is
started on the given cfs_rq, and due to the cpuset it would not happen,
this load would never be properly unloaded. With this patch the load
will be properly removed inside update_blocked_averages. This also
applies to tasks moved to the fair scheduling class and moved to another
cpu, and this path will also fix that. For fork, the entity is queued
right away, so this problem does not affect that.
This applies to cases where the new process is the first in the cfs_rq,
issue introduced 3d30544f0212 ("sched/fair: Apply more PELT fixes"), and
when there has previously been load on the cgroup but the cgroup was
removed from the leaflist due to having null PELT load, indroduced
in 039ae8bcf7a5 ("sched/fair: Fix O(nr_cgroups) in the load balancing
path").
For a simple cgroup hierarchy (as seen below) with two equally weighted
groups, that in theory should get 50/50 of cpu time each, it often leads
to a load of 60/40 or 70/30.
If the hierarchy is deeper (as seen below), while keeping cg-1 and cg-2
equally weighted, they should still get a 50/50 balance of cpu time.
This however sometimes results in a balance of 10/90 or 1/99(!!) between
the task groups.
This can be reproduced by attaching an idle process to a cgroup and
moving it to a given cpuset before it wakes up. The issue is evident in
many (if not most) container runtimes, and has been reproduced
with both crun and runc (and therefore docker and all its "derivatives"),
and with both cgroup v1 and v2.
Fixes: 3d30544f0212 ("sched/fair: Apply more PELT fixes") Fixes: 039ae8bcf7a5 ("sched/fair: Fix O(nr_cgroups) in the load balancing path") Signed-off-by: Odin Ugedal <odin@uged.al> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/20210501141950.23622-2-odin@uged.al Signed-off-by: Sasha Levin <sashal@kernel.org>
Util-clamp places tasks in different buckets based on their clamp values
for performance reasons. However, the size of buckets is currently
computed using a rounding division, which can lead to an off-by-one
error in some configurations.
For instance, with 20 buckets, the bucket size will be 1024/20=51. A
task with a clamp of 1024 will be mapped to bucket id 1024/51=20. Sadly,
correct indexes are in range [0,19], hence leading to an out of bound
memory access.
The m_can_start_xmit() function checks if the cdev->tx_skb is NULL and
returns with NETDEV_TX_BUSY in case tx_sbk is not NULL.
There is a race condition in the m_can_tx_work_queue(), where first
the skb is send to the driver and then the case tx_sbk is set to NULL.
A TX complete IRQ might come in between and wake the queue, which
results in tx_skb not being cleared yet.
syzbot is able to setup kTLS on an SMC socket which coincidentally
uses sk_user_data too. Later, kTLS treats it as psock so triggers a
refcnt warning. The root cause is that smc_setsockopt() simply calls
TCP setsockopt() which includes TCP_ULP. I do not think it makes
sense to setup kTLS on top of SMC sockets, so we should just disallow
this setup.
It is hard to find a commit to blame, but we can apply this patch
since the beginning of TCP_ULP.
Reported-and-tested-by: syzbot+b54a1ce86ba4a623b7f0@syzkaller.appspotmail.com Fixes: 734942cc4ea6 ("tcp: ULP infrastructure") Cc: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Android userspace has been using TCA_KIND with a char[IFNAMESIZ]
many-null-terminated buffer containing the string 'bpf'.
This works on 4.19 and ceases to work on 5.10.
I'm not entirely sure what fixes tag to use, but I think the issue
was likely introduced in the below mentioned 5.4 commit.
Reported-by: Nucca Chen <nuccachen@google.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: David Ahern <dsahern@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@mellanox.com> Cc: Jiri Pirko <jiri@resnulli.us> Fixes: 62794fc4fbf5 ("net_sched: add max len check for TCA_KIND")
Change-Id: I66dc281f165a2858fc29a44869a270a2d698a82b Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing rmap_item from stable tree, STABLE_FLAG of rmap_item is
cleared with head reserved. So the following scenario might happen: For
ksm page with rmap_item1:
cmp_and_merge_page
stable_node->head = &migrate_nodes;
remove_rmap_item_from_tree, but head still equal to stable_node;
try_to_merge_with_ksm_page failed;
return;
For the same ksm page with rmap_item2, stable node migration succeed this
time. The stable_node->head does not equal to migrate_nodes now. For ksm
page with rmap_item1 again:
We would miss the rmap_item for stable_node and might result in failed
rmap_walk_ksm(). Fix this by set rmap_item->head to NULL when rmap_item
is removed from stable tree.
Link: https://lkml.kernel.org/r/20210330140228.45635-5-linmiaohe@huawei.com Fixes: 4146d2d673e8 ("ksm: make !merge_across_nodes migration safe") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the zone device page does not belong to un-addressable device memory,
the variable entry will be uninitialized and lead to indeterminate pte
entry ultimately. Fix this unexpected case and warn about it.
Link: https://lkml.kernel.org/r/20210325131524.48181-4-linmiaohe@huawei.com Fixes: df6ad69838fc ("mm/device-public-memory: device memory cache coherent with CPU") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Rafael Aquini <aquini@redhat.com> Cc: Yang Shi <shy828301@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A rare out of memory error would prevent removal of the reserve map region
for a page. hugetlb_fix_reserve_counts() handles this rare case to avoid
dangling with incorrect counts. Unfortunately, hugepage_subpool_get_pages
and hugetlb_acct_memory could possibly fail too. We should correctly
handle these cases.
Link: https://lkml.kernel.org/r/20210410072348.20437-5-linmiaohe@huawei.com Fixes: b5cec28d36f5 ("hugetlbfs: truncate_hugepages() takes a range of pages") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Feilong Lin <linfeilong@huawei.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In writable and !referenced case, the result value should be
SCAN_LACK_REFERENCED_PAGE for trace_mm_collapse_huge_page_isolate()
instead of default 0 (SCAN_FAIL) here.
Link: https://lkml.kernel.org/r/20210306032947.35921-5-linmiaohe@huawei.com Fixes: 7d2eba0557c1 ("mm: add tracepoint for scanning pages") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Dan Carpenter <dan.carpenter@oracle.com> Cc: Ebru Akagunduz <ebru.akagunduz@gmail.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An out of bounds write happens when setting the default power state.
KASAN sees this as:
[drm] radeon: 512M of GTT memory ready.
[drm] GART: num cpu pages 131072, num gpu pages 131072
==================================================================
BUG: KASAN: slab-out-of-bounds in
radeon_atombios_parse_power_table_1_3+0x1837/0x1998 [radeon]
Write of size 4 at addr ffff88810178d858 by task systemd-udevd/157
Without KASAN, this will manifest later when the kernel attempts to
allocate memory that was stomped, since it collides with the inline slab
freelist pointer:
Normally SCTP_MIB_CURRESTAB is always incremented once asoc enter into
ESTABLISHED from the state < ESTABLISHED and decremented when the asoc
is being deleted.
However, in sctp_sf_do_dupcook_b(), the asoc's state can be changed to
ESTABLISHED from the state >= ESTABLISHED where it shouldn't increment
SCTP_MIB_CURRESTAB. Otherwise, one asoc may increment MIB_CURRESTAB
multiple times but only decrement once at the end.
I was able to reproduce it by using scapy to do the 4-way shakehands,
after that I replayed the COOKIE-ECHO chunk with 'peer_vtag' field
changed to different values, and SCTP_MIB_CURRESTAB was incremented
multiple times and never went back to 0 even when the asoc was freed.
This patch is to fix it by only incrementing SCTP_MIB_CURRESTAB when
the state < ESTABLISHED in sctp_sf_do_dupcook_b().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In enic_hard_start_xmit, it calls enic_queue_wq_skb(). Inside
enic_queue_wq_skb, if some error happens, the skb will be freed
by dev_kfree_skb(skb). But the freed skb is still used in
skb_tx_timestamp(skb).
My patch makes enic_queue_wq_skb() return error and goto spin_unlock()
incase of error. The solution is provided by Govind.
See https://lkml.org/lkml/2021/4/30/961.
Fixes: fb7516d42478e ("enic: add sw timestamp support") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Acked-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a misplaced barrier in call_decode. The struct rpc_rqst is modified
as follows by xprt_complete_rqst:
req->rq_private_buf.len = copied;
/* Ensure all writes are done before we update */
/* req->rq_reply_bytes_recvd */
smp_wmb();
req->rq_reply_bytes_recvd = copied;
And currently read as follows by call_decode:
smp_rmb(); // misplaced
if (!req->rq_reply_bytes_recvd)
goto out;
req->rq_rcv_buf.len = req->rq_private_buf.len;
This patch places the smp_rmb after the if to ensure that
rq_reply_bytes_recvd and rq_private_buf.len are read in order.
We should return a negative error code upon failure in
riscv_hartid_to_cpuid() instead of NR_CPUS. This is also
aligned with all uses of riscv_hartid_to_cpuid() which
expect negative error code upon failure.
Fixes: 6825c7a80f18 ("RISC-V: Add logical CPU indexing for RISC-V") Fixes: f99fb607fb2b ("RISC-V: Use Linux logical CPU number instead of hartid") Signed-off-by: Anup Patel <anup.patel@wdc.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is caused by a transport use-after-free issue. When processing a
duplicate COOKIE-ECHO chunk in sctp_sf_do_dupcook_a(), both COOKIE-ACK
and SHUTDOWN chunks are allocated with the transort from the new asoc.
However, later in the sideeffect machine, the old asoc is used to send
them out and old asoc's shutdown_last_sent_to is set to the transport
that SHUTDOWN chunk attached to in sctp_cmd_setup_t2(), which actually
belongs to the new asoc. After the new_asoc is freed and the old asoc
T2 timeout, the old asoc's shutdown_last_sent_to that is already freed
would be accessed in sctp_sf_t2_timer_expire().
Thanks Alexander and Jere for helping dig into this issue.
To fix it, this patch is to do the asoc update first, then allocate
the COOKIE-ACK and SHUTDOWN chunks with the 'updated' old asoc. This
would make more sense, as a chunk from an asoc shouldn't be sent out
with another asoc. We had fixed quite a few issues caused by this.
Fixes: 145cb2f7177d ("sctp: Fix bundling of SHUTDOWN with COOKIE-ACK") Reported-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Reported-by: syzbot+bbe538efd1046586f587@syzkaller.appspotmail.com Reported-by: Michal Tesar <mtesar@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If selftest and reset are performed at the same time, the phy
loopback setting may be still in enable state after the reset,
and device cannot link up. So fix this issue by disabling phy
loopback before phy_start().
Fixes: 256727da7395 ("net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, netif_tx_stop_all_queues() is used to ensure that
the xmit is not running, but for the concurrent case it will
not take effect, since netif_tx_stop_all_queues() just sets
a flag without locking to indicate that the xmit queue(s)
should not be run.
So use netif_tx_disable() to replace netif_tx_stop_all_queues(),
it takes the xmit queue lock while marking the queue stopped.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When skb->ip_summed is CHECKSUM_PARTIAL, for non-tunnel udp packet,
which has a dest port as the IANA assigned, the hardware is expected
to do the checksum offload, but the hardware whose version is below
V3 will not do the checksum offload when udp dest port is 4790.
So fixes it by doing the checksum in software for this case.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In some cases, the device is not initialized because reset failed.
If another task calls hns3_reset_notify_up_enet() before reset
retry, it will cause an error since uninitialized pointer access.
So add check for HNS3_NIC_STATE_INITED before calling
hns3_nic_net_open() in hns3_reset_notify_up_enet().
Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The message sent to VF should be initialized, otherwise random
value of some contents may cause improper processing by the target.
So add a initialization to message in hclge_get_link_mode().
Fixes: 9194d18b0577 ("net: hns3: fix the problem that the supported port is empty") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the UM, the type and enable status of igu_egu_hw_err
should be configured separately. Currently, the type field is
incorrect when disable this error. So fix it by configuring these
two fields separately.
Fixes: bf1faf9415dd ("net: hns3: Add enable and process hw errors from IGU, EGU and NCSI") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 878dabb64117 ("ceph: don't return -ESTALE if there's still an open file") Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the client ignores the value of the sr_eof of the SEEK
operation. According to the spec, if the server didn't find the
requested extent and reached the end of the file, the server
would return sr_eof=true. In case the request for DATA and no
data was found (ie in the middle of the hole), then the lseek
expects that ENXIO would be returned.
We (adam zabrocki, alexander matrosov, alexander tereshkin, maksym
bazalii) observed the check:
if (fh->size > sizeof(struct nfs_fh))
should not use the size of the nfs_fh struct which includes an extra two
bytes from the size field.
struct nfs_fh {
unsigned short size;
unsigned char data[NFS_MAXFHSIZE];
}
but should determine the size from data[NFS_MAXFHSIZE] so the memcpy
will not write 2 bytes beyond destination. The proposed fix is to
compare against the NFS_MAXFHSIZE directly, as is done elsewhere in fs
code base.
Fixes: d67ae825a59d ("pnfs/flexfiles: Add the FlexFile Layout Driver") Signed-off-by: Nikola Livic <nlivic@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the missing destroy_workqueue() before return from
pci_epf_test_init() in the error handling case and add
destroy_workqueue() in pci_epf_test_exit().
Link: https://lore.kernel.org/r/20210331084012.2091010-1-yangyingliang@huawei.com Fixes: 349e7a85b25fa ("PCI: endpoint: functions: Add an EP function to test PCI") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to use unsigned long subtraction and then convert to signed in
order to deal correcly with C overflow rules.
Fixes: f5062003465c ("NFS: Set an attribute barrier on all updates") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When idr_find() returns NULL to intent, no error return code of
qcom_glink_rx_data() is assigned.
To fix this bug, ret is assigned with -ENOENT in this case.
Fixes: 64f95f87920d ("rpmsg: glink: Use the local intents when receiving data") Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Link: https://lore.kernel.org/r/20210306133624.17237-1-baijiaju1990@gmail.com Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 1879445dfa7b ("perf/core: Set event's default
::overflow_handler()") set a default event->overflow_handler in
perf_event_alloc(), and replace the check event->overflow_handler with
is_default_overflow_handler(), but one is missing.
Currently, the bp->overflow_handler can not be NULL. As a result,
enable_single_step() is always not invoked.
Fixes: 1879445dfa7b ("perf/core: Set event's default ::overflow_handler()") Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Cc: Wang Nan <wangnan0@huawei.com> Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pci_scan_device(), if pci_setup_device() fails for any reason, the code
will not release device's of_node by calling pci_release_of_node(). Fix
that by calling the release function.
Fixes: 98d9f30c820d ("pci/of: Match PCI devices to OF nodes dynamically") Link: https://lore.kernel.org/r/20210124232826.1879-1-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The uninitialized variable dn.node_changed does not get set when a
call to f2fs_get_node_page fails. This uninitialized value gets used
in the call to f2fs_balance_fs() that may or not may not balances
dirty node and dentry pages depending on the uninitialized state of
the variable. Fix this by only calling f2fs_balance_fs if err is
not set.
Thanks to Jaegeuk Kim for suggesting an appropriate fix.
Addresses-Coverity: ("Uninitialized scalar variable") Fixes: 2a3407607028 ("f2fs: call f2fs_balance_fs only when node was changed") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kcalloc() returns NULL to __tcbp or of_count_phandle_with_args()
returns zero or -ENOENT to count, no error return code of
thermal_of_populate_bind_params() is assigned.
To fix these bugs, ret is assigned with -ENOMEM and -ENOENT in these
cases, respectively.
Fixes: a92bab8919e3 ("of: thermal: Allow multiple devices to share cooling map") Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210310122423.3266-1-baijiaju1990@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Noticed failure as a crash on ia64 when tried to symbolize all backtraces
collected by page_owner=on:
$ cat /sys/kernel/debug/page_owner
<oops>
CPU: 1 PID: 2074 Comm: cat Not tainted 5.12.0-rc4 #226
Hardware name: hp server rx3600, BIOS 04.03 04/08/2008
ip is at dereference_module_function_descriptor+0x41/0x100
Crash happens at dereference_module_function_descriptor() due to
use-after-free when dereferencing ".opd" section header.
All section headers are already freed after module is laoded successfully.
To keep symbolizer working the change stores ".opd" address and size after
module is relocated to a new place and before section headers are
discarded.
To make similar errors less obscure module_finalize() now zeroes out all
variables relevant to module loading only.
Link: https://lkml.kernel.org/r/20210403074803.3309096-1-slyfox@gentoo.org Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Support VF device IDs used by the Hyper-V hypervisor.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Reviewed-by: Andy Gospodarek <gospo@broadcom.com> Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The IOMMU table is divided into pools for concurrent mappings and each
pool has a separate spinlock. When taking the ownership of an IOMMU group
to pass through a device to a VM, we lock these spinlocks which triggers
a false negative warning in lockdep (below).
This fixes it by annotating the large pool's spinlock as a nest lock
which makes lockdep not complaining when locking nested locks if
the nest lock is locked already.
===
WARNING: possible recursive locking detected
5.11.0-le_syzkaller_a+fstn1 #100 Not tainted
--------------------------------------------
qemu-system-ppc/4129 is trying to acquire lock: c0000000119bddb0 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
but task is already holding lock: c0000000119bdd30 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
other info that might help us debug this:
Possible unsafe locking scenario:
Function qtnf_event_handle_external_auth calls memcpy without
checking the length.
A user could control that length and trigger a buffer overflow.
Fix by checking the length is within the maximum allowed size.
Fix the following out-of-bounds warnings by adding a new structure
wl3501_req instead of duplicating the same members in structure
wl3501_join_req and wl3501_scan_confirm:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [39, 108] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 36 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [25, 95] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 22 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
bunch of struct members adjacent to each other in a single call to
memcpy(). Now that a new struct wl3501_req enclosing all those adjacent
members is introduced, memcpy() doesn't overrun the length of
&sig.beacon_period and &this->bss_set[i].beacon_period, because the
address of the new struct object _req_ is used as the destination,
instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Fix the following out-of-bounds warnings by enclosing structure members
daddr and saddr into new struct addr, in structures wl3501_md_req and
wl3501_md_ind:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
couple of arrays adjacent to each other in a single call to memcpy().
Now that a new struct _addr_ enclosing those two adjacent arrays
is introduced, memcpy() doesn't overrun the length of &sig.daddr[0]
and &sig.daddr, because the address of the new struct object _addr_
is used, instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
projects / linux-stable / log