optee_shm_register() expected pages to be passed as an array of page
pointers rather than as an array of contiguous pages. So fix that via
correctly passing pages as per expectation.
Fixes: a249dd200d03 ("tee: optee: Fix dynamic shm pool allocations") Reported-by: Vincent Cao <vincent.t.cao@intel.com> Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Tested-by: Vincent Cao <vincent.t.cao@intel.com> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 287422a95fe2 ("drm/rockchip: Round up _before_ giving to the clock framework")
changed what rate clk_round_rate() is called with, an additional 999 Hz
added to the requsted mode clock. This has caused a regression on RK3328
and presumably also on RK3228 because the inno-hdmi-phy clock requires an
exact match of the requested rate in the pre pll config table.
When an exact match is not found the parent clock rate (24MHz) is returned
to the clk_round_rate() caller. This cause wrong pixel clock to be used and
result in no-signal when configuring a mode on RK3328.
Fix this by rounding the rate down to closest 1000 Hz in round_rate func,
this allows an exact match to be found in pre pll config table.
Fixes: 287422a95fe2 ("drm/rockchip: Round up _before_ giving to the clock framework") Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gcc has a hard time tracking whether BUG_ON(1) ends
execution or not:
drivers/gpio/gpio-aspeed-sgpio.c: In function 'bank_reg':
drivers/gpio/gpio-aspeed-sgpio.c:112:1: error: control reaches end of non-void function [-Werror=return-type]
Use the simpler BUG() that gcc knows cannot continue.
Dev_hold has to be called always in netdev_queue_add_kobject.
Otherwise usage count drops below 0 in case of failure in
kobject_init_and_add.
Fixes: b8eb718348b8 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject") Reported-by: Hulk Robot <hulkci@huawei.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: David Miller <davem@davemloft.net> Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The cio layer's intparm logic does not align itself well with how qeth
manages cmd IOs. When an active IO gets terminated via halt/clear, the
corresponding IRQ's intparm does not reflect the cmd buffer but rather
the intparm that was passed to ccw_device_halt() / ccw_device_clear().
This behaviour was recently clarified in
commit b91d9e67e50b ("s390/cio: fix intparm documentation").
As a result, qeth_irq() currently doesn't cancel a cmd that was
terminated via halt/clear. This primarily causes us to leak
card->read_cmd after the qeth device is removed, since our IO path still
holds a refcount for this cmd.
For qeth this means that we need to keep track of which IO is pending on
a device ('active_cmd'), and use this as the intparm when calling
halt/clear. Otherwise qeth_irq() can't match the subsequent IRQ to its
cmd buffer.
Since we now keep track of the _expected_ intparm, we can also detect
any mismatch; this would constitute a bug somewhere in the lower layers.
In this case cancel the active cmd - we effectively "lost" the IRQ and
should not expect any further notification for this IO.
Fixes: 405548959cc7 ("s390/qeth: add support for dynamically allocated cmds") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
7c20f11680a4 ("bio-integrity: stop abusing bi_end_io") moves
bio_integrity_free from bio_uninit() to bio_integrity_verify_fn()
and bio_endio(). This way looks wrong because bio may be freed
without calling bio_endio(), for example, blk_rq_unprep_clone() is
called from dm_mq_queue_rq() when the underlying queue of dm-mpath
is busy.
So memory leak of bio integrity data is caused by commit 7c20f11680a4.
Fixes this issue by re-adding bio_integrity_free() to bio_uninit().
Fixes: 7c20f11680a4 ("bio-integrity: stop abusing bi_end_io") Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by Justin Tee <justin.tee@broadcom.com>
Add commit log, and simplify/fix the original patch wroten by Justin.
Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is caused by dereferencing 'dev_data' after put_device() in
the telem_device_remove() function.
This patch just moves the put_device() down a bit to avoid this
issue.
Fixes: 1210d1e6bad1 ("platform/chrome: wilco_ec: Add telemetry char device interface") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Cc: Benson Leung <bleung@chromium.org> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com> Cc: Nick Crews <ncrews@chromium.org> Cc: linux-kernel@vger.kernel.org Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Tetsuo pointed out that it was not only the device unregister hook that was
broken for devmap_hash types, it was also cleanup on map free. So better
fix this as well.
While we're at it, there's no reason to allocate the netdev_map array for
DEVMAP_HASH, so skip that and adjust the cost accordingly.
Fixes: 6f9d451ab1a3 ("xdp: Add devmap_hash map type for looking up devices by hashed index") Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20191121133612.430414-1-toke@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The INTERRUPT_CNTL2 register expects a valid DMA address, but is
currently set with a GPU MC address. This can cause problems on
systems that detect the resulting DMA read from an invalid address
(found on a Power8 guest).
Instead, use the DMA address of the dummy page because it will always
be safe.
Fixes: d8f60cfc9345 ("drm/radeon/kms: Add support for interrupts on r6xx/r7xx chips (v3)") Fixes: 25a857fbe973 ("drm/radeon/kms: add support for interrupts on SI") Fixes: a59781bbe528 ("drm/radeon: add support for interrupts on CIK (v5)") Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fs/afs/dir_edit.c: In function afs_set_contig_bits:
fs/afs/dir_edit.c:75:20: warning: variable after set but not used [-Wunused-but-set-variable]
fs/afs/dir_edit.c: In function afs_set_contig_bits:
fs/afs/dir_edit.c:75:12: warning: variable before set but not used [-Wunused-but-set-variable]
fs/afs/dir_edit.c: In function afs_clear_contig_bits:
fs/afs/dir_edit.c:100:20: warning: variable after set but not used [-Wunused-but-set-variable]
fs/afs/dir_edit.c: In function afs_clear_contig_bits:
fs/afs/dir_edit.c:100:12: warning: variable before set but not used [-Wunused-but-set-variable]
usb drivers are supposed to communicate using usb_interface instead
mt76x{0,2}u is now registering through usb_device. Fix it by passing
usb_intf device to mt76_alloc_device routine.
Fixes: 112f980ac8926 ("mt76usb: use usb_dev private data") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Tested-By: Zero_Chaos <sidhayn@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
update_cfs_rq_load_avg() calls cfs_rq_util_change() every time PELT decays,
which might be inefficient when the cpufreq driver has rate limitation.
When a task is attached on a CPU, we have this call path:
update_load_avg()
update_cfs_rq_load_avg()
cfs_rq_util_change -- > trig frequency update
attach_entity_load_avg()
cfs_rq_util_change -- > trig frequency update
The 1st frequency update will not take into account the utilization of the
newly attached task and the 2nd one might be discarded because of rate
limitation of the cpufreq driver.
update_cfs_rq_load_avg() is only called by update_blocked_averages()
and update_load_avg() so we can move the call to
cfs_rq_util_change/cpufreq_update_util() into these two functions.
It's also interesting to note that update_load_avg() already calls
cfs_rq_util_change() directly for the !SMP case.
This change will also ensure that cpufreq_update_util() is called even
when there is no more CFS rq in the leaf_cfs_rq_list to update, but only
IRQ, RT or DL PELT signals.
xdr_shrink_pagelen() BUG's when @len is larger than buf->page_len.
This can happen when xdr_buf_read_mic() is given an xdr_buf with
a small page array (like, only a few bytes).
Instead, just cap the number of bytes that xdr_shrink_pagelen()
will move.
Fixes: 5f1bc39979d ("SUNRPC: Fix buffer handling of GSS MIC ... ") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
An additional check has been recently added to ensure that a RCU related lock
is held while the RCU list is iterated.
The `pwqs' are sometimes iterated without a RCU lock but with the &wq->mutex
acquired leading to a warning.
Teach list_for_each_entry_rcu() that the RCU usage is okay if &wq->mutex
is acquired during the list traversal.
Fixes: 28875945ba98d ("rcu: Add support for consolidated-RCU reader checking") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Prior to this patch in optee_probe() when optee_enumerate_devices() was
called the struct optee was fully initialized. If
optee_enumerate_devices() returns an error optee_probe() is supposed to
clean up and free the struct optee completely, but will at this late
stage need to call optee_remove() instead. This isn't done and thus
freeing the struct optee prematurely.
With this patch the call to optee_enumerate_devices() is done after
optee_probe() has returned successfully and in case
optee_enumerate_devices() fails everything is cleaned up with a call to
optee_remove().
In case of dynamic shared memory pool, kernel memory allocated using
dmabuf_mgr pool needs to be registered with OP-TEE prior to its usage
during optee_open_session() or optee_invoke_func().
So fix dmabuf_mgr pool allocations via an additional call to
optee_shm_register().
Also, allow kernel pages to be registered as shared memory with OP-TEE.
Fixes: 9733b072a12a ("optee: allow to work without static shared memory") Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
v4.11-rc1 did introduce a patch series that rearranged the
sdio quirks into a header file. Unfortunately this did forget
to handle SDIO_VENDOR_ID_TI differently between wl1251 and
wl1271 with the result that although the wl1251 was found on
the sdio bus, the firmware did not load any more and there was
no interface registration.
This patch defines separate constants to be used by sdio quirks
and drivers.
Fixes: 884f38607897 ("mmc: core: move some sdio IDs out of quirks file") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Cc: <stable@vger.kernel.org> # v4.11+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The logic to ring the scmi performance fastchannel ignores the
value read from the doorbell register in case of !CONFIG_64BIT.
This bug also shows up as warning with '-Wunused-but-set-variable' gcc
flag:
drivers/firmware/arm_scmi/perf.c: In function scmi_perf_fc_ring_db:
drivers/firmware/arm_scmi/perf.c:323:7: warning: variable val set but
not used [-Wunused-but-set-variable]
Fix the same by aligning the logic with CONFIG_64BIT as used in the
macro SCMI_PERF_FC_RING_DB().
Fixes: 823839571d76 ("firmware: arm_scmi: Make use SCMI v2.0 fastchannel for performance protocol") Reported-by: Hulk Robot <hulkci@huawei.com> Reported-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is necessary to set fd to -1 when inotify_add_watch() fails in
cg_prepare_for_wait. Otherwise the fd which has been closed in
cg_prepare_for_wait may be misused in other functions such as
cg_enter_and_wait_for_frozen and cg_freeze_wait.
Distinguish between the case where dma information is not provided
within the DT and the case of an error during the dma init.
Exit the probe with error in case of an error during dma init.
Adding a couple of READ_ONCE()/WRITE_ONCE() should silence it.
Since the report hinted about multiple cpus using the history
concurrently, I added a test avoiding writing on it if the
victim slot already contains the desired value.
[1]
BUG: KCSAN: data-race in fanout_demux_rollover / fanout_demux_rollover
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 18922 Comm: syz-executor.3 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 3b3a5b0aab5b ("packet: rollover huge flows before small flows") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The module alias platform tag contains a spelling mistake. Fix it.
Fixes: f33506abbcdd ("rtc: bd70528: Add MODULE ALIAS to autoload module") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20191106083418.159045-1-colin.king@canonical.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The default installation location for gen_kselftest_tar.sh was still
"kselftest/" which collides with the existing directory. Instead, this
moves the installation target into "kselftest_install/kselftest/" and
adjusts the tar creation accordingly. This also adjusts indentation and
logic to be consistent.
In the DMA memory resource get failed case, the error is not
set and 0 will be returned. Fix it by removing redundant check
since devm_ioremap_resource() will handle it.
Fixes: 28ef9ebdb64c ("net: axienet: make use of axistream-connected attribute optional") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A difference of two unsigned long needs long storage.
Fixes: c7fb64db001f ("[NETLINK]: Neighbour table configuration and statistics via rtnetlink") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On 2019-10-28 06:07, wbob wrote:
> Hello Roman,
>
> while reading around drivers/net/wireless/ralink/rt2x00/rt2800lib.c
> I stumbled on what I think is an edit of yours made in error in march
> 2017:
>
> https://github.com/torvalds/linux/commit/41977e86#diff-dae5dc10da180f3b055809a48118e18aR5281
>
> RT6352 in line 5281 should not have been introduced as the "else if"
> below line 5291 can then not take effect for a RT6352 device. Another
> possibility is for line 5291 to be not for RT6352, but this seems
> very unlikely. Are you able to clarify still after this substantial time?
>
> 5277: static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
> ...
> 5279: } else if (rt2x00_rt(rt2x00dev, RT5390) ||
> 5280: rt2x00_rt(rt2x00dev, RT5392) ||
> 5281: rt2x00_rt(rt2x00dev, RT6352)) {
> ...
> 5291: } else if (rt2x00_rt(rt2x00dev, RT6352)) {
> ...
Hence remove errornous line 5281 to make the driver actually
execute the correct initialization routine for MT7620 chips.
As it was requested by Stanislaw Gruszka remove setting values of
MIMO_PS_CFG and TX_PIN_CFG. MIMO_PS_CFG is responsible for MIMO
power-safe mode (which is disabled), hence we can drop setting it.
TX_PIN_CFG is set correctly in other functions, and as setting this
value breaks some devices, rather don't set it here during init, but
only modify it later on.
Fixes: 41977e86c984 ("rt2x00: add support for MT7620") Reported-by: wbob <wbob@jify.de> Reported-by: Roman Yeryomin <roman@advem.lv> Signed-off-by: Daniel Golle <daniel@makrotopia.org> Acked-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the driver needs to create a hash value because it
was not done at higher level, then the hash should be marked
as a software not hardware hash.
Fixes: f72860afa2e3 ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing") Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlocking of a not locked mutex is not allowed.
Other kernel thread may be in critical section while
we unlock it because of setting user_feature fail.
Fixes: 95a7233c4 ("net: openvswitch: Set OvS recirc_id from tc chain index") Cc: Paul Blakey <paulb@mellanox.com> Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Tested-by: Greg Rose <gvrose8192@gmail.com> Acked-by: William Tu <u9012063@gmail.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no need to call ufshcd_def_desc_sizes() in ufshcd_init(), since
descriptor lengths will be checked and initialized later in
ufshcd_init_desc_sizes().
Fixes: a4b0e8a4e92b1b(scsi: ufs: Factor out ufshcd_read_desc_param) Link: https://lore.kernel.org/r/BN7PR08MB5684A3ACE214C3D4792CE729DB610@BN7PR08MB5684.namprd08.prod.outlook.com Signed-off-by: Bean Huo <beanhuo@micron.com> Acked-by: Avri Altman <avri.altman.wdc.com> Reviewed-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dpaa_cleanup_tx_fd() function is called by the frame transmit
confirmation callback but also on several error paths. This function
is reading the transmit timestamp value. Avoid reading an invalid
timestamp value on the error paths.
Fixes: 4664856e9ca2 ("dpaa_eth: add support for hardware timestamping") Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
DMA unmapping is required before accessing the HW provided timestamping
information.
Fixes: 4664856e9ca2 ("dpaa_eth: add support for hardware timestamping") Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We never set this to false. This probably doesn't affect most people's
runtime because GCC will automatically initialize it to false at certain
common optimization levels. But that behavior is related to a bug in
GCC and obviously should not be relied on.
Fixes: 5d6742b37727 ("rcu/nocb: Use rcu_segcblist for no-CBs CPUs") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bd70528 charger driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell for
charger is added.
Fixes: f8c7f7ddd8ef0 ("power: supply: Initial support for ROHM BD70528 PMIC charger block") Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch complains that we need to initialized "*cap" otherwise it can
lead to an uninitialized variable bug in the caller. This seems like a
reasonable warning and it doesn't hurt to silence it at least.
drivers/gpu/drm/amd/amdgpu/vi.c:767 vi_asic_reset_method() error: uninitialized symbol 'baco_reset'.
Fixes: 425db2553e43 ("drm/amdgpu: expose BACO interfaces to upper level from PP") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bd70528 regulator driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell for
regulators is added.
Fixes: 99ea37bd1e7d7 ("regulator: bd70528: Support ROHM BD70528 regulator block") Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Link: https://lore.kernel.org/r/20191023121452.GA1812@localhost.localdomain Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since 5.4-rc1, pwm_apply_state calls ->get_state after ->apply
if available, and this revealed an issue with integer precision
when calculating duty_cycle and period for the currently set
state in ->get_state callback.
This issue manifested in broken backlight on several Allwinner
based devices.
Previously this worked, because ->apply updated the passed state
directly.
Fixes: deb9c462f4e53 ("pwm: sun4i: Don't update the state for the caller of pwm_apply_state") Signed-off-by: Ondrej Jirman <megous@megous.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When commit 68bdb6773289 ("ACPI: add support for ACPI reconfiguration
notifiers") introduced reconfiguration notifiers, it missed the point
that the ACPI table, which might be loaded and then unloaded via
ConfigFS, could contain devices that were not enumerated by their
parents.
In such cases, the stale platform device is dangling in the system
while the rest of the devices from the same table are already gone.
Introduce acpi_platform_device_remove_notify() notifier that, in
similar way to I²C or SPI buses, unregisters the platform devices
on table removal event.
Fixes: 68bdb6773289 ("ACPI: add support for ACPI reconfiguration notifiers")
Depends-on: 00500147cbd3 ("drivers: Introduce device lookup variants by ACPI_COMPANION device") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ rjw: Changelog & function rename ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
bpf_xdp_adjust_head() can change the frame boundaries. Account for the
potential shift properly by calculating the new offset before
syncing the buffer to the device for XDP_TX
Fixes: ba2b232108d3 ("net: netsec: add XDP support") Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 5cca30ebe089be23 ("drm/rcar-du: Add LVDS_LANES quirk") states
that LVDS lanes 1 and 3 are inverted on R-Car H2 ES1 only, and that the
problem has been fixed in newer revisions.
However, the code didn't take into account the actual hardware revision,
thus applying the quirk also on newer hardware revisions, causing green
color reversals.
Fix this by applying the quirk when running on R-Car H2 ES1.x only.
The software_node_get_parent() returned a pointer to the parent swnode,
but did not take a reference to it, leading the caller to put a reference
that was not taken. Take that reference now.
Fixes: 59abd83672f7 ("drivers: base: Introducing software nodes to the firmware node framework") Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
I'm embarassed to say that even though I've touched
vop_crtc_mode_fixup() twice and I swear I tested it, there's still a
stupid glaring bug in it. Specifically, on veyron_minnie (with all
the latest display timings) we want to be setting our pixel clock to
66,666,666.67 Hz and we tell userspace that's what we set, but we're
actually choosing 66,000,000 Hz. This is confirmed by looking at the
clock tree.
The problem is that in drm_display_mode_from_videomode() we convert
from Hz to kHz with:
dmode->clock = vm->pixelclock / 1000;
...and drm_display_mode_from_videomode() is called from panel-simple
when we have an "override_mode" like we do on veyron_minnie. See
commit 123643e5c40a ("ARM: dts: rockchip: Specify
rk3288-veyron-minnie's display timings").
...so when the device tree specifies a clock of 66666667 for the panel
then DRM translates that to 66666000. The clock framework will always
pick a clock that is _lower_ than the one requested, so it will refuse
to pick 66666667 and we'll end up at 66000000.
While we could try to fix drm_display_mode_from_videomode() to round
to the nearest kHz and it would fix our problem, it wouldn't help if
the clock we actually needed was 60,000,001 Hz. We could
alternatively have DRM always round up, but maybe this would break
someone else who already baked in the assumption that DRM rounds down.
Specifically note that clock drivers are not consistent about whether
they round up or round down when you call clk_set_rate(). We know how
Rockchip's clock driver works, but (for instance) you can see that on
most Qualcomm clocks the default is clk_rcg2_ops which rounds up.
Let's solve this by just adding 999 Hz before calling
clk_round_rate(). This should be safe and work everywhere. As
discussed in more detail in comments in the commit, Rockchip's PLLs
are configured in a way that there shouldn't be another PLL setting
that is only a few kHz off so we won't get mixed up.
NOTE: if this is picked to stable, it's probably easiest to first pick
commit 527e4ca3b6d1 ("drm/rockchip: Base adjustments of the mode based
on prev adjustments") which shouldn't hurt in stable.
Commit 0ed266d7ae5e ("clk: ti: omap3: cleanup unnecessary clock aliases")
removed old omap3 clock framework aliases but caused omap3-rom-rng to
stop working with clock not found error.
Based on discussions on the mailing list it was requested by Tero Kristo
that it would be best to fix this issue by probing omap3-rom-rng using
device tree to provide a proper clk property. The other option would be
to add back the missing clock alias, but that does not help moving things
forward with removing old legacy platform_data.
Let's also add a proper device tree binding and keep it together with
the fix.
Cc: devicetree@vger.kernel.org Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Adam Ford <aford173@gmail.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Sebastian Reichel <sre@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Fixes: 0ed266d7ae5e ("clk: ti: omap3: cleanup unnecessary clock aliases") Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/gpu/drm/amd/amdgpu/vcn_v2_5.c:431: warning: Excess function
parameter 'sw' description in 'vcn_v2_5_disable_clock_gating'
drivers/gpu/drm/amd/amdgpu/vcn_v2_5.c:550: warning: Excess function
parameter 'sw' description in 'vcn_v2_5_enable_clock_gating'
The "lvds->backlight" pointer could be NULL in situations where
of_parse_phandle() returns NULL. This code is cleaner if we use the
managed devm_of_find_backlight() so the clean up is automatic.
When modifying panfrost_devfreq_target() to support a device without a
regulator defined I missed the check on the error path. Let's add it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: e21dd290881b ("drm/panfrost: Enable devfreq to work without regulator") Signed-off-by: Steven Price <steven.price@arm.com> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190822093218.26014-1-steven.price@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When downloading the reserved page, the first page always contains
a beacon for the firmware to reference. For non-beaconing modes such
as station mode, also put a blank skb with length=1.
And for the beaconing modes, driver will get a real beacon with a
length approximate to the page size. But as the beacon is always put
at the first page, it does not need a tx_desc, because the TX path
will generate one when TXing the reserved page to the hardware. So we
could allocate a buffer with a size smaller than the reserved page,
when using memcpy() to copy the content of reserved page to the buffer,
the over-sized reserved page will violate the kernel memory.
To fix it, add the tx_desc before memcpy() the reserved packets to
the buffer, then we can get SKBs with correct length when counting
the pages in total. And for page 0, count the extra tx_desc_sz that
the TX path will generate. This way, the first beacon that allocated
without tx_desc can be counted with the extra tx_desc_sz to get
actual pages it requires.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver") Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since gpiochip_remove() calls gpiochip_remove_pin_ranges() unconditionally,
we have duplicate call to the same function when it's not necessary.
Move gpiochip_remove_pin_ranges() from of_gpiochip_add() to gpiochip_add()
to avoid duplicate calls and be consistent with the explicit call in
gpiochip_remove().
It turns out there really is something special to the first
set_next_task() invocation. In specific the 'change' pattern really
should not cause balance callbacks.
snoop_file_poll() is defined as returning 'unsigned int' but the
.poll method is declared as returning '__poll_t', a bitwise type.
Fix this by using the proper return type and using the EPOLL
constants instead of the POLL ones, as required for __poll_t.
Link: https://lore.kernel.org/r/20191121051851.268726-1-joel@jms.id.au Fixes: 3772e5da4454 ("drivers/misc: Aspeed LPC snoop output using misc chardev") Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the DTB for a device with an RZ/A2 SoC lacks a device node for the
BSID register, the ID validation code falls back to using a register at
address 0x0, which leads to undefined behavior (e.g. reading back a
random value).
This could be fixed by letting fam_rza2.reg point to the actual BSID
register. However, the hardcoded fallbacks were meant for backwards
compatibility with old DTBs only, not for new SoCs. Hence fix this by
validating renesas_family.reg before using it.
We'll end up with debugfs collisions if we don't give names to the
regmaps created by this driver. Change the name of the config before
registering it so we don't collide in debugfs.
Fixes: 7f9c136216c7 ("soc: qcom: Add broadcast base for Last Level Cache Controller (LLCC)") Cc: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org> Reviewed-by: Evan Green <evgreen@chromium.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupts that don't have an associated wake event or GPIO wake events
end up with an associate IRQ chip that is NULL and which causes IRQ code
to crash. This is because we don't implicitly set the parent IRQ chip by
allocating the interrupt at the parent. However, there really isn't a
corresponding interrupt at the parent, so we need to work around this by
setting the special no_irq_chip as the IRQ chip for these interrupts.
The TLC chips actually offer 257 levels:
- 0: led OFF
- 1-255: Led dimmed is using a PWM. The duty cycle range from 0.4% to 99.6%
- 256: led fully ON
Fixes: e370d010a5fe ("leds: tlc591xx: Driver for the TI 8/16 Channel i2c LED driver") Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At some point in the past we needed to make sure we would get the long
name of modules and not just what we get from /proc/modules, but that
need, as described in the cset that introduced the adjustment function:
Fixes: c03d5184f0e9 ("perf machine: Adjust dso->long_name for offline module")
Without using the buildid-cache:
# lsmod | grep trusted
# insmod trusted.ko
# lsmod | grep trusted
trusted 24576 0
# strace -e open,openat perf probe -m ./trusted.ko key_seal |& grep trusted
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 7
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/trusted.ko/dd3d355d567394d540f527e093e0f64b95879584/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
probe:key_seal (on key_seal in trusted)
# perf probe -l
probe:key_seal (on key_seal in trusted)
#
No attempt at opening '[trusted]'.
Now using the build-id cache:
# rmmod trusted
# perf buildid-cache --add ./trusted.ko
# insmod trusted.ko
# strace -e open,openat perf probe -m ./trusted.ko key_seal |& grep trusted
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/trusted/notes/.note.gnu.build-id", O_RDONLY) = 7
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/trusted.ko/dd3d355d567394d540f527e093e0f64b95879584/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/trusted.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "trusted.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/trusted.ko", O_RDONLY) = 3
#
Again, no attempt at reading '[trusted]'.
Finally, adding a probe to that function and then using:
This was the only path I could find using the perf tools that reach at this
function, then as of november/2019, if we put a probe in the line where the
actuall setting of the dso->long_name is done:
To further test this I used kvm.ko as the offline module, i.e. removed
if from the buildid-cache by nuking it completely (rm -rf ~/.debug) and
moved it from the normal kernel distro path, removed the modules, stoped
the kvm guest, and then installed it manually, etc.
# rmmod kvm-intel
# rmmod kvm
# lsmod | grep kvm
# modprobe kvm-intel
modprobe: ERROR: ctx=0x55d3b1722260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: ctx=0x55d3b1722260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: could not insert 'kvm_intel': Unknown symbol in module, or unknown parameter (see dmesg)
# insmod ./kvm.ko
# modprobe kvm-intel
modprobe: ERROR: ctx=0x562f34026260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
modprobe: ERROR: ctx=0x562f34026260 path=/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm/kvm.ko.xz error=No such file or directory
# lsmod | grep kvm
kvm_intel 299008 0
kvm 765952 1 kvm_intel
irqbypass 16384 1 kvm
#
# perf probe -x ~/bin/perf machine__findnew_module_map:12 mname=m.name:string filename=filename:string 'dso_long_name=map->dso->long_name:string' 'dso_name=map->dso->name:string'
# perf probe -l
probe_perf:machine__findnew_module_map (on machine__findnew_module_map:12@util/machine.c in /home/acme/bin/perf with mname filename dso_long_name dso_name)
# perf record
^C[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 3.416 MB perf.data (33956 samples) ]
# perf trace -e probe_perf:machine*
<SNIP>
6.322 perf/23099 probe_perf:machine__findnew_module_map(__probe_ip: 5492493, mname: "[salsa20_generic]", filename: "/lib/modules/5.3.8-200.fc30.x86_64/kernel/crypto/salsa20_generic.ko.xz", dso_long_name: "/lib/modules/5.3.8-200.fc30.x86_64/kernel/crypto/salsa20_generic.ko.xz", dso_name: "[salsa20_generic]")
6.375 perf/23099 probe_perf:machine__findnew_module_map(__probe_ip: 5492493, mname: "[kvm]", filename: "[kvm]", dso_long_name: "[kvm]", dso_name: "[kvm]")
<SNIP>
The filename doesn't come with the path, no point in trying to set the dso->long_name.
[root@quaco ~]# strace -e open,openat perf probe -m ./kvm.ko kvm_apic_local_deliver |& egrep 'open.*kvm'
openat(AT_FDCWD, "/sys/module/kvm_intel/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/sys/module/kvm/notes/.note.gnu.build-id", O_RDONLY) = 4
openat(AT_FDCWD, "/lib/modules/5.3.8-200.fc30.x86_64/kernel/arch/x86/kvm", O_RDONLY|O_NONBLOCK|O_CLOEXEC|O_DIRECTORY) = 7
openat(AT_FDCWD, "/sys/module/kvm_intel/notes/.note.gnu.build-id", O_RDONLY) = 8
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/.debug/root/kvm.ko/5955f426cb93f03f30f3e876814be2db80ab0b55/probes", O_RDWR|O_CREAT, 0644) = 3
openat(AT_FDCWD, "/usr/lib/debug/root/kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/usr/lib/debug/root/kvm.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/.debug/kvm.ko", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, ".debug/kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "kvm.ko.debug", O_RDONLY) = -1 ENOENT (No such file or directory)
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 4
openat(AT_FDCWD, "/root/kvm.ko", O_RDONLY) = 3
[root@quaco ~]#
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Wang Nan <wangnan0@huawei.com> Link: https://lkml.kernel.org/n/tip-jlfew3lyb24d58egrp0o72o2@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch restores the CRYPTO_AES dependency. This is
necessary since some of the crypto4xx driver provided
modes need functioning software fallbacks for
AES-CTR/CCM and GCM.
Fixes: da3e7a9715ea ("crypto: amcc - switch to AES library for GCM key derivation") Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Acked-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy client tracking infrastructure of nfsd makes use of MD5 to
derive a client's recovery directory name. As the nfsd module doesn't
declare any dependency on CRYPTO_MD5, though, it may fail to allocate
the hash if the kernel was compiled without it. As a result, generation
of client recovery directories will fail with the following error:
NFSD: unable to generate recoverydir name
The explicit dependency on CRYPTO_MD5 was removed as redundant back in 6aaa67b5f3b9 (NFSD: Remove redundant "select" clauses in fs/Kconfig
2008-02-11) as it was already implicitly selected via RPCSEC_GSS_KRB5.
This broke when RPCSEC_GSS_KRB5 was made optional for NFSv4 in commit df486a25900f (NFS: Fix the selection of security flavours in Kconfig) at
a later point.
Fix the issue by adding back an explicit dependency on CRYPTO_MD5.
Fixes: df486a25900f (NFS: Fix the selection of security flavours in Kconfig) Signed-off-by: Patrick Steinhardt <ps@pks.im> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case of an invalid virtchannel request the driver
would return uninitialized data to the VF from the PF stack
which is a bug. Fix by initializing the stack variable
earlier in the function before any return paths can be taken.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support") Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if they are not currently used fix BK/BE endpoint definition order.
Fixes: b40b15e1521f ("mt76: add usb support to mt76 layer") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now phy-gmii-sel will disable MAC TX internal delay for PHY interface mode
"rgmii-rxid" which is incorrect.
Hence, fix it by enabling MAC TX internal delay in the case of "rgmii-rxid"
mode.
Commit 0fc9ae107669 ("net: phy: broadcom: add support for
BCM54210E") added support for BCM54210E but also unconditionally cleared
the RXC to RXD skew and the TXD to TXC skew, thus only making
PHY_INTERFACE_MODE_RGMII a possible configuration. Use
bcm54xx_config_clock_delay() which correctly sets the registers
depending on the 4 possible PHY interface values that exist for RGMII.
Fixes: 0fc9ae107669 ("net: phy: broadcom: add support for BCM54210E") Reported-by: Manasa Mudireddy <manasa.mudireddy@broadcom.com> Reported-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function __tipc_shutdown(), the timeout value passed to
tipc_wait_for_cond() is not jiffies.
This commit fixes it by converting that value from milliseconds
to jiffies.
Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion") Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tipc_sk_timeout() is executed but user space is grabbing
ownership, this function rearms itself and returns. However, the
socket reference counter is not reduced. This causes potential
unexpected behavior.
This commit fixes it by calling sock_put() before tipc_sk_timeout()
returns in the above-mentioned case.
Fixes: afe8792fec69 ("tipc: refactor function tipc_sk_timeout()") Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When initiating a connection message to a server side, the connection
message is cloned and added to the socket write queue. However, if the
cloning is failed, only the socket write queue is purged. It causes
memory leak because the original connection message is not freed.
This commit fixes it by purging the list of connection message when
it cannot be cloned.
Fixes: 6787927475e5 ("tipc: buffer overflow handling in listener socket") Reported-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 25b0b9c4e835 ("tipc: handle collisions of 32-bit node address
hash values"), the 32-bit node address only generated after one second
trial period expired. However the self's addr in struct tipc_monitor do
not update according to node address generated. This lead to it is
always zero as initial value. As result, sorting algorithm using this
value does not work as expected, neither neighbor monitoring framework.
In this commit, we add a fix to update self's addr when 32-bit node
address generated.
Fixes: 25b0b9c4e835 ("tipc: handle collisions of 32-bit node address hash values") Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With huge cluster (e.g >200nodes), the amount of that flow:
gap -> retransmit packet -> acked will take time in case of STATE_MSG
dropped/delayed because a lot of traffic. This lead to 1.5 sec tolerance
value criteria made link easy failure around 2nd, 3rd of failed
retransmission attempts.
Instead of re-introduced criteria of 99 faled retransmissions to fix the
issue, we increase failure detection timer to ten times tolerance value.
Fixes: 77cf8edbc0e7 ("tipc: simplify stale link failure criteria") Acked-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Acked-by: Jon Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
powerpc: Use hardware RNG for arch_get_random_seed_* not arch_get_random_*
updated arch_get_random_[int|long]() to be NOPs, and moved the hardware
RNG backing to arch_get_random_seed_[int|long]() instead. However, it
failed to take into account that arch_get_random_int() was implemented
in terms of arch_get_random_long(), and so we ended up with a version
of the former that is essentially a NOP as well.
Fix this by calling arch_get_random_seed_long() from
arch_get_random_seed_int() instead.
Fixes: 01c9348c7620ec65 ("powerpc: Use hardware RNG for arch_get_random_seed_* not arch_get_random_*") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191204115015.18015-1-ardb@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"powerpc_security_features" is "unsigned long", i.e. 32-bit or 64-bit,
depending on the platform (PPC_FSL_BOOK3E or PPC_BOOK3S_64). Hence
casting its address to "u64 *", and calling debugfs_create_x64() is
wrong, and leaks 32-bit of nearby data to userspace on 32-bit platforms.
While all currently defined SEC_FTR_* security feature flags fit in
32-bit, they all have "ULL" suffixes to make them 64-bit constants.
Hence fix the leak by changing the type of "powerpc_security_features"
(and the parameter types of its accessors) to "u64". This also allows
to drop the cast.
Fixes: 398af571128fe75f ("powerpc/security: Show powerpc_security_features in debugfs") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191021142309.28105-1-geert+renesas@glider.be Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that for callback requests, the reported backlog latency
is always zero, and the rtt value is crazy big. The problem was that
rqst->rq_xtime is never set for backchannel requests.
Fixes: 78215759e20d ("SUNRPC: Make RTT measurement more ... ") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gss_read_proxy_verf() assumes things about the XDR buffer containing
the RPC Call that are not true for buffers generated by
svc_rdma_recv().
RDMA's buffers look more like what the upper layer generates for
sending: head is a kmalloc'd buffer; it does not point to a page
whose contents are contiguous with the first page in the buffers'
page array. The result is that ACCEPT_SEC_CONTEXT via RPC/RDMA has
stopped working on Linux NFS servers that use gssproxy.
This does not affect clients that use only TCP to send their
ACCEPT_SEC_CONTEXT operation (that's all Linux clients). Other
clients, like Solaris NFS clients, send ACCEPT_SEC_CONTEXT on the
same transport as they send all other NFS operations. Such clients
can send ACCEPT_SEC_CONTEXT via RPC/RDMA.
I thought I had found every direct reference in the server RPC code
to the rqstp->rq_pages field.
Bug found at the 2019 Westford NFS bake-a-thon.
Fixes: 3316f0631139 ("svcrdma: Persistently allocate and DMA- ... ") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Tested-by: Bill Baker <bill.baker@oracle.com> Reviewed-by: Simo Sorce <simo@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turned out Intel Gemini Lake doesn't use the same I2C timing
parameters as Broxton.
I got confirmation from the Windows team that Gemini Lake systems should
use updated timing parameters that differ from those used in Broxton
based systems.
Fixes: f80e78aa11ad ("mfd: intel-lpss: Add Intel Gemini Lake PCI IDs") Tested-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a typo in the free slave id search loop. Instead of I2C_CLIENT_PEC,
it should have been I2C_CLIENT_TEN. The slave id 1 can only handle 7-bit
addresses and thus is not eligible in case of 10-bit addresses.
As a matter of fact none of the slave id support I2C_CLIENT_PEC, overall
check is performed at the beginning of the stm32f7_i2c_reg_slave function.
The IP can handle two slave addresses. One address can either be
7 bits or 10 bits while the other can only be 7 bits.
In order to ensure that a 10 bits address can always be allocated
(assuming there is only one 7 bits address already allocated),
pick up the 7-bits only address slot in priority when performing a 7-bits
address allocation.
Flags passed to Q_XQUOTARM were not sanity checked for invalid values.
Fix that.
Fixes: 9da93f9b7cdf ("xfs: fix Q_XQUOTARM ioctl") Reported-by: Yang Xu <xuyang2018.jy@cn.fujitsu.com> Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A coccicheck run provided information like the following.
arch/arm/mach-omap2/display.c:268:2-8: ERROR: missing put_device;
call of_find_device_by_node on line 258, but without a corresponding
object release within this function.
With the removal of the panel-dpi from the omap drivers, the
LCD no longer works. This patch points the device tree to
a newly created panel named "logicpd,type28"
Fixes: 8bf4b1621178 ("drm/omap: Remove panel-dpi driver") Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the days of using bpf_load.c the order in which the 'maps' sections
were defines in BPF side (*_kern.c) file, were used by userspace side
to identify the map via using the map order as an index. In effect the
order-index is created based on the order the maps sections are stored
in the ELF-object file, by the LLVM compiler.
This have also carried over in libbpf via API bpf_map__next(NULL, obj)
to extract maps in the order libbpf parsed the ELF-object file.
When BTF based maps were introduced a new section type ".maps" were
created. I found that the LLVM compiler doesn't create the ".maps"
sections in the order they are defined in the C-file. The order in the
ELF file is based on the order the map pointer is referenced in the code.
This combination of changes lead to xdp_rxq_info mixing up the map
file-descriptors in userspace, resulting in very broken behaviour, but
without warning the user.
This patch fix issue by instead using bpf_object__find_map_by_name()
to find maps via their names. (Note, this is the ELF name, which can
be longer than the name the kernel retains).
Fixes: be5bca44aa6b ("samples: bpf: convert some XDP samples from bpf_load to libbpf") Fixes: 451d1dc886b5 ("samples: bpf: update map definition to new syntax BTF-defined map") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/157529025128.29832.5953245340679936909.stgit@firesoul Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since, the new syntax of BTF-defined map has been introduced,
the syntax for using maps under samples directory are mixed up.
For example, some are already using the new syntax, and some are using
existing syntax by calling them as 'legacy'.
As stated at commit abd29c931459 ("libbpf: allow specifying map
definitions using BTF"), the BTF-defined map has more compatablility
with extending supported map definition features.
The commit doesn't replace all of the map to new BTF-defined map,
because some of the samples still use bpf_load instead of libbpf, which
can't properly create BTF-defined map.
This will only updates the samples which uses libbpf API for loading bpf
program. (ex. bpf_prog_load_xattr)
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com> Acked-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While trying to figure out why fentry_fexit selftest doesn't pass for me
(old pahole, broken BTF), I found out that my latest patch can break vmlinux
.BTF generation. objcopy preserves section start when doing --only-section,
so there is a chance (depending on where pahole inserts .BTF section) to
have leading empty zeroes. Let's explicitly force section offset to zero.
As part of this change, I'm also dropping '2>/dev/null' from objcopy
invocation to be able to catch possible other issues (objcopy doesn't
produce any warnings for me anymore, it did before with --dump-section).
Fixes: da5fb18225b4 ("bpf: Support pre-2.25-binutils objcopy for vmlinux BTF") Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Cc: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/20191127225759.39923-1-sdf@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Perform size check always in btf__resolve_size. Makes the logic a bit more
robust against corrupted BTF and silences LGTM/Coverity complaining about
always true (size < 0) check.
Coverity scan against Github libbpf code found the issue of not freeing memory and
leaving already freed memory still referenced from bpf_program. Fix it by
re-assigning successfully reallocated memory sooner.
Fixes: 2993e0515bb4 ("tools/bpf: add support to read .BTF.ext sections") Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20191107020855.3834758-2-andriin@fb.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log