If a callback break occurs (change notification), afs_getattr() needs to
issue an FS.FetchStatus RPC operation to update the status of the file
being examined by the stat-family of system calls.
Fix afs_getattr() to do this if AFS_VNODE_CB_PROMISED has been cleared
on a vnode by a callback break. Skip this if AT_STATX_DONT_SYNC is set.
This can be tested by appending to a file on one AFS client and then
using "stat -L" to examine its length on a machine running kafs. This
can also be watched through tracing on the kafs machine. The callback
break is seen:
The asm_cpu_bringup_and_idle() function is required to push the return
value on the stack in order to make ORC happy, but the only reason
objtool doesn't complain is because of a happy accident.
The thing is that asm_cpu_bringup_and_idle() doesn't return, so
validate_branch() never terminates and falls through to the next
function, which in the normal case is the hypercall_page. And that, as
it happens, is 4095 NOPs and a RET.
Make asm_cpu_bringup_and_idle() terminate on it's own, by making the
function it calls as a dead-end. This way we no longer rely on what
code happens to come after.
Fixes: c3881eb58d56 ("x86/xen: Make the secondary CPU idle tasks reliable") Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Juergen Gross <jgross@suse.com> Reviewed-by: Miroslav Benes <mbenes@suse.cz> Link: https://lore.kernel.org/r/20210624095147.693801717@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2f62f36e62daec ("x86/xen: Make the boot CPU idle task reliable")
introduced a regression for booting 32 bit Xen PV guests: the address
of the initial stack needs to be a virtual one.
Fixes: 2f62f36e62daec ("x86/xen: Make the boot CPU idle task reliable") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/20200409070001.16675-1-jgross@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Halil Pasic points out [1] that the full revert of that commit (revert
in bddac7c1e02b), and that a partial revert that only reverts the
problematic case, but still keeps some of the cleanups is probably
better. 
And that partial revert [2] had already been verified by Oleksandr
Natalenko to also fix the issue, I had just missed that in the long
discussion.
So let's reinstate the cleanups from commit aa6f8dcbab47 ("swiotlb:
rework "fix info leak with DMA_FROM_DEVICE""), and effectively only
revert the part that caused problems.
The audio_mclk_root_clk was added as a gate with the CCGR121 (0x4790),
but according to the reference manual, there is no such gate. Moreover,
the consumer driver of the mentioned clock might gate it and leave
the ECSPI2 (the true owner of that gate) hanging. So lets use the
audio_mclk_post_div, which is the parent.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
[ps: backport to 5.4] Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device drivers may decide to not load firmware when probed to avoid
slowing down the boot process should the firmware filesystem not be
available yet. In this case, the firmware loading request may be done
when a device file associated with the driver is first accessed. The
credentials of the userspace process accessing the device file may be
used to validate access to the firmware files requested by the driver.
Ensure that the kernel assumes the responsibility of reading the
firmware.
This was observed on Android for a graphic driver loading their firmware
when the device file (e.g. /dev/mali0) was first opened by userspace
(i.e. surfaceflinger). The security context of surfaceflinger was used
to validate the access to the firmware file (e.g.
/vendor/firmware/mali.bin).
Previously, Android configurations were not setting up the
firmware_class.path command line argument and were relying on the
userspace fallback mechanism. In this case, the security context of the
userspace daemon (i.e. ueventd) was consistently used to read firmware
files. More Android devices are now found to set firmware_class.path
which gives the kernel the opportunity to read the firmware directly
(via kernel_read_file_from_path_initns). In this scenario, the current
process credentials were used, even if unrelated to the loading of the
firmware file.
Signed-off-by: Thiébaud Weksteen <tweek@google.com> Cc: <stable@vger.kernel.org> # 5.10 Reviewed-by: Paul Moore <paul@paul-moore.com> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Link: https://lore.kernel.org/r/20220502004952.3970800-1-tweek@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on DesignWare Ethernet QoS datasheet, we are seeing the limitation
of Split Header (SPH) feature is not supported for Ipv4 fragmented packet.
This SPH limitation will cause ping failure when the packets size exceed
the MTU size. For example, the issue happens once the basic ping packet
size is larger than the configured MTU size and the data is lost inside
the fragmented packet, replaced by zeros/corrupted values, and leads to
ping fail.
So, disable the Split Header for Intel platforms.
v2: Add fixes tag in commit message.
Fixes: 67afd6d1cfdf("net: stmmac: Add Split Header support and enable it in XGMAC cores") Cc: <stable@vger.kernel.org> # 5.10.x Suggested-by: Ong, Boon Leong <boon.leong.ong@intel.com> Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com> Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When merging one bio to request, if they are discard IO and the queue
supports multi-range discard, we need to return ELEVATOR_DISCARD_MERGE
because both block core and related drivers(nvme, virtio-blk) doesn't
handle mixed discard io merge(traditional IO merge together with
discard merge) well.
Fix the issue by returning ELEVATOR_DISCARD_MERGE in this situation,
so both blk-mq and drivers just need to handle multi-range discard.
According to Ilitek "231x & ILI251x Programming Guide" Version: 2.30
"2.1. Power Sequence", "T4 Chip Reset and discharge time" is minimum
10ms and "T2 Chip initial time" is maximum 150ms. Adjust the reset
timings such that T4 is 12ms and T2 is 160ms to fit those figures.
This prevents sporadic touch controller start up failures when some
systems with at least ILI251x controller boot, without this patch
the systems sometimes fail to communicate with the touch controller.
Bounds check hw_head index provided by NIC to verify it lies
within the TX buffer ring.
Reported-by: Aashay Shringarpure <aashay@google.com> Reported-by: Yi Chou <yich@google.com> Reported-by: Shervin Oloumi <enlightened@google.com> Signed-off-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'ping' utility is able to manage two kind of sockets (raw or icmp),
depending on the sysctl ping_group_range. By default, ping_group_range is
set to '1 0', which forces ping to use an ip raw socket.
Let's replay the ping tests by allowing 'ping' to use the ip icmp socket.
After the previous patch, ipv4 tests results are the same with both kinds
of socket. For ipv6, there are a lot a new failures (the previous patch
fixes only two cases).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the QoS ack policy was set to non explicit / psmp ack, frames are treated
as not being part of a BA session, which causes extra latency on reordering.
Fix this by only bypassing reordering for packets with no-ack policy
# make DEBUG=y bench/numa.o
...
bench/numa.c: In function ‘__bench_numa’:
bench/numa.c:1749:81: error: ‘%d’ directive output may be truncated
writing between 1 and 11 bytes into a region of size between
10 and 20 [-Werror=format-truncation=]
1749 | snprintf(tname, sizeof(tname), "process%d:thread%d", p, t);
^~
...
bench/numa.c:1749:64: note: directive argument in the range
[-2147483647, 2147483646]
...
#
The maximum length of the %d replacement is 11 characters because of the
negative sign. Therefore extend the array by two more characters.
Output after:
# make DEBUG=y bench/numa.o > /dev/null 2>&1; ll bench/numa.o
-rw-r--r-- 1 root root 418320 May 19 09:11 bench/numa.o
#
Fixes: 3aff8ba0a4c9c919 ("perf bench numa: Avoid possible truncation when using snprintf()") Suggested-by: Namhyung Kim <namhyung@gmail.com> Signed-off-by: Thomas Richter <tmricht@linux.ibm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Sumanth Korikkar <sumanthk@linux.ibm.com> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Link: https://lore.kernel.org/r/20220520081158.2990006-1-tmricht@linux.ibm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For gpio controller contain register PDDR, when set one target bit,
current logic will clear all other bits, this is wrong. Use operator
'|=' to fix it.
It is possible to stack bridges on top of each other. Consider the
following which makes use of an Ethernet switch:
br1
/ \
/ \
/ \
br0.11 wlan0
|
br0
/ | \
p1 p2 p3
br0 is offloaded to the switch. Above br0 is a vlan interface, for
vlan 11. This vlan interface is then a slave of br1. br1 also has a
wireless interface as a slave. This setup trunks wireless lan traffic
over the copper network inside a VLAN.
A frame received on p1 which is passed up to the bridge has the
skb->offload_fwd_mark flag set to true, indicating that the switch has
dealt with forwarding the frame out ports p2 and p3 as needed. This
flag instructs the software bridge it does not need to pass the frame
back down again. However, the flag is not getting reset when the frame
is passed upwards. As a result br1 sees the flag, wrongly interprets
it, and fails to forward the frame to wlan0.
When passing a frame upwards, clear the flag. This is the Rx
equivalent of br_switchdev_frame_unmark() in br_dev_xmit().
Fixes: f1c2eddf4cb6 ("bridge: switchdev: Use an helper to clear forward mark") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20220518005840.771575-1-andrew@lunn.ch Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
igb_read_phy_reg() will silently return, leaving phy_data untouched, if
hw->ops.read_reg isn't set. Depending on the uninitialized value of
phy_data, this led to the phy status check either succeeding immediately
or looping continuously for 2 seconds before emitting a noisy err-level
timeout. This message went out to the console even though there was no
actual problem.
Instead, first check if there is read_reg function pointer. If not,
proceed without trying to check the phy status register.
Fixes: b72f3f72005d ("igb: When GbE link up, wait for Remote receiver status condition") Signed-off-by: Kevin Mitchell <kevmitch@arista.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In Thumb2, 'b . + 4' produces a branch instruction that uses a narrow
encoding, and so it does not jump to the following instruction as
expected. So use W(b) instead.
Fixes: 6c7cb60bff7a ("ARM: fix Thumb2 regression with Spectre BHB") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Spectre-BHB mitigations were inadvertently left disabled for
Cortex-A15, due to the fact that cpu_v7_bugs_init() is not called in
that case. So fix that.
Fixes: b9baf5c8c5c3 ("ARM: Spectre-BHB workaround") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If skb_clone() returns null pointer, pfkey_broadcast() will
return error.
Therefore, it should be better to check the return value of
pfkey_broadcast() and return error if fails.
LRO is incompatible and mutually exclusive with XDP. However, the needed
checks are only made when enabling XDP. If LRO is enabled when XDP is
already active, the command will succeed, and XDP will be skipped in the
data path, although still enabled.
This commit fixes the bug by checking the XDP status in
mlx5e_fix_features and disabling LRO if XDP is enabled.
There are sleep in atomic context bugs when the request to secure
element of st-nci is timeout. The root cause is that nci_skb_alloc
with GFP_KERNEL parameter is called in st_nci_se_wt_timeout which is
a timer handler. The call paths that could trigger bugs are shown below:
This patch changes allocation mode of nci_skb_alloc from GFP_KERNEL to
GFP_ATOMIC in order to prevent atomic context sleeping. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
Fixes: ed06aeefdac3 ("nfc: st-nci: Rename st21nfcb to st-nci") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220517012530.75714-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
test_bit() tests if one bit is set or not.
Here the logic seems to check of bit QL_RESET_PER_SCSI (i.e. 4) OR bit
QL_RESET_START (i.e. 3) is set.
In fact, it checks if bit 7 (4 | 3 = 7) is set, that is to say
QL_ADAPTER_UP.
This looks harmless, because this bit is likely be set, and when the
ql_reset_work() delayed work is scheduled in ql3xxx_isr() (the only place
that schedule this work), QL_RESET_START or QL_RESET_PER_SCSI is set.
clk_generated_best_diff() helps in finding the parent and the divisor to
compute a rate closest to the required one. However, it doesn't take into
account the request's range for the new rate. Make sure the new rate
is within the required range.
Fixes: 8a8f4bf0c480 ("clk: at91: clk-generated: create function to find best_diff") Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20220413071318.244912-1-codrin.ciubotariu@microchip.com Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hardware statistics counters are not cleared during resets so the
drivers first access is to initialize the baseline and then subsequent
reads are for reporting the counters. The statistics counters are read
during the watchdog subtask when the interface is up. If the baseline
is not initialized before the interface is up, then there can be a brief
window in which some traffic can be transmitted/received before the
initial baseline reading takes place.
Directly initialize ethtool statistics in driver open so the baseline will
be initialized when the interface is up, and any dropped packets
incremented before the interface is up won't be reported.
Fixes: 28dc1b86f8ea9 ("ice: ignore dropped packets during init") Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In vmxnet3_rq_create(), when dma_alloc_coherent() fails,
vmxnet3_rq_destroy() is called. It sets rq->rx_ring[i].base to NULL. Then
vmxnet3_rq_create() returns an error to its callers mxnet3_rq_create_all()
-> vmxnet3_change_mtu(). Then vmxnet3_change_mtu() calls
vmxnet3_force_close() -> dev_close() in error handling code. And the driver
calls vmxnet3_close() -> vmxnet3_quiesce_dev() -> vmxnet3_rq_cleanup_all()
-> vmxnet3_rq_cleanup(). In vmxnet3_rq_cleanup(),
rq->rx_ring[ring_idx].base is accessed, but this variable is NULL, causing
a NULL pointer dereference.
To fix this possible bug, an if statement is added to check whether
rq->rx_ring[0].base is NULL in vmxnet3_rq_cleanup() and exit early if so.
The error log in our fault-injection testing is shown as follows:
In vmxnet3_rq_alloc_rx_buf(), when dma_map_single() fails, rbi->skb is
freed immediately. Similarly, in another branch, when dma_map_page() fails,
rbi->page is also freed. In the two cases, vmxnet3_rq_alloc_rx_buf()
returns an error to its callers vmxnet3_rq_init() -> vmxnet3_rq_init_all()
-> vmxnet3_activate_dev(). Then vmxnet3_activate_dev() calls
vmxnet3_rq_cleanup_all() in error handling code, and rbi->skb or rbi->page
are freed again in vmxnet3_rq_cleanup_all(), causing use-after-free bugs.
To fix these possible bugs, rbi->skb and rbi->page should be cleared after
they are freed.
The error log in our fault-injection testing is shown as follows:
The 'shift' field is not validated, and any value above 31 will
trigger out-of-bounds. The issue predates the git history, but
syzbot was able to trigger it only after the commit mentioned in
the fixes tag, and this change only applies on top of such commit.
Address the issue bounding the 'shift' value to the maximum allowed
by the relevant operator.
Reported-and-tested-by: syzbot+8ed8fc4c57e9dcf23ca6@syzkaller.appspotmail.com Fixes: 8b796475fd78 ("net/sched: act_pedit: really ensure the skb is writable") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In gem_rx_refill rx_prepared_head is incremented at the beginning of
the while loop preparing the skb and data buffers. If the skb or data
buffer allocation fails, this BD will be unusable BDs until the head
loops back to the same BD (and obviously buffer allocation succeeds).
In the unlikely event that there's a string of allocation failures,
there will be an equal number of unusable BDs and an inconsistent RX
BD chain. Hence increment the head at the end of the while loop to be
clean.
FWSPIDQ2 and FWSPIDQ3 are not part of FWSPI18 interface so remove
FWQSPID group in pinctrl dtsi. These pins must be used with the
FWSPI pins that are dedicated for boot SPI interface which provides
same 3.3v logic level.
Fixes: 2f6edb6bcb2f ("ARM: dts: aspeed: Fix AST2600 quad spi group") Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20220329173932.2588289-2-quic_jaehyoo@quicinc.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit referenced in the Fixes tag removed the 'break' from the else
branch in qcom_rng_read(), causing an infinite loop whenever 'max' is
not a multiple of WORD_SZ. This can be reproduced e.g. by running:
kcapi-rng -b 67 >/dev/null
There are many ways to fix this without adding back the 'break', but
they all seem more awkward than simply adding it back, so do just that.
Tested on a machine with Qualcomm Amberwing processor.
Fixes: a680b1832ced ("crypto: qcom-rng - ensure buffer for generate is completely filled") Cc: stable@vger.kernel.org Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Reviewed-by: Brian Masney <bmasney@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When zapping obsolete pages, update the running count of zapped pages
regardless of whether or not the list has become unstable due to zapping
a shadow page with its own child shadow pages. If the VM is backed by
mostly 4kb pages, KVM can zap an absurd number of SPTEs without bumping
the batch count and thus without yielding. In the worst case scenario,
this can cause a soft lokcup.
If a Root Port on Elo i2 is put into D3cold and then back into D0, the
downstream device becomes permanently inaccessible, so add a bridge D3 DMI
quirk for that system.
This was exposed by 14858dcc3b35 ("PCI: Use pci_update_current_state() in
pci_enable_device_flags()"), but before that commit the Root Port in
question had never been put into D3cold for real due to a mismatch between
its power state retrieved from the PCI_PM_CTRL register (which was
accessible even though the platform firmware indicated that the port was in
D3cold) and the state of an ACPI power resource involved in its power
management.
Descriptor table is a shared resource; two fget() on the same descriptor
may return different struct file references. get_tap_ptr_ring() is
called after we'd found (and pinned) the socket we'll be using and it
tries to find the private tun/tap data structures associated with it.
Redoing the lookup by the same file descriptor we'd used to get the
socket is racy - we need to same struct file.
Thanks to Jason for spotting a braino in the original variant of patch -
I'd missed the use of fd == -1 for disabling backend, and in that case
we can end up with sock == NULL and sock != oldsock.
Cc: stable@kernel.org Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Norbert reported that it's possible to race sys_perf_event_open() such
that the looser ends up in another context from the group leader,
triggering many WARNs.
The move_group case checks for races against itself, but the
!move_group case doesn't, seemingly relying on the previous
group_leader->ctx == ctx check. However, that check is racy due to not
holding any locks at that time.
Therefore, re-check the result after acquiring locks and bailing
if they no longer match.
Additionally, clarify the not_move_group case from the
move_group-vs-move_group race.
The antient ISA wavefront driver reads its sample patch data (uploaded
over an ioctl) via __get_user() with no good reason; likely just for
some performance optimizations in the past. Let's change this to the
standard get_user() and the error check for handling the fault case
properly.
We must ensure that all sockets are closed before we call xprt_free()
and release the reference to the net namespace. The problem is that
calling fput() will defer closing the socket until delayed_fput() gets
called.
Let's fix the situation by allowing rpciod and the transport teardown
code (which runs on the system wq) to call __fput_sync(), and directly
close the socket.
Reported-by: Felix Fu <foyjog@gmail.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Fixes: a73881c96d73 ("SUNRPC: Fix an Oops in udp_poll()") Cc: stable@vger.kernel.org # 5.1.x: 3be232f11a3c: SUNRPC: Prevent immediate close+reconnect Cc: stable@vger.kernel.org # 5.1.x: 89f42494f92f: SUNRPC: Don't call connect() more than once on a TCP socket Cc: stable@vger.kernel.org # 5.1.x Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
[meenashanmugam: Fix merge conflict in xprt_connect] Signed-off-by: Meena Shanmugam <meenashanmugam@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid socket state races due to repeated calls to ->connect() using the
same socket. If connect() returns 0 due to the connection having
completed, but we are in fact in a closing state, then we may leave the
XPRT_CONNECTING flag set on the transport.
All callers of __mmc_switch() should now be specifying a valid timeout for
the CMD6 command. However, just to be sure, let's print a warning and
default to use the generic_cmd6_time in case the provided timeout_ms
argument is zero.
In this context, let's also simplify some of the corresponding code and
clarify some related comments.
The INAND_CMD38_ARG_EXT_CSD is a vendor specific EXT_CSD register, which is
used to prepare an erase/trim operation. However, it doesn't make sense to
use a timeout of 10 minutes while updating the register, which becomes the
case when the timeout_ms argument for mmc_switch() is set to zero.
Instead, let's use the generic_cmd6_time, as that seems like a reasonable
timeout to use for these cases.
The timeout values used while waiting for a CMD6 for BKOPS or a CACHE_FLUSH
to complete, are not defined by the eMMC spec. However, a timeout of 10
minutes as is currently being used, is just silly for both of these cases.
Instead, let's specify more reasonable timeouts, 120s for BKOPS and 30s for
CACHE_FLUSH.
During disk space reclamation, nilfs2 still emits the following lockdep
warning due to page/folio operations on shadowed page caches that nilfs2
uses to get a snapshot of DAT file in memory:
The first two are to resolve the lockdep warning issue, and the last one
is the accompanying cleanup and low priority.
Based on your comment, this series solves the issue by separating inode
object as needed. Since I was worried about the impact of the object
composition changes, I tested the series carefully not to cause
regressions especially for delicate functions such like disk space
reclamation and snapshots.
This patch (of 3):
If CONFIG_LOCKDEP is enabled, nilfs2 hits lockdep warnings at
inode_to_wb() during page/folio operations for btree nodes:
This is because nilfs2 uses two page caches for each inode and
inode->i_mapping never points to one of them, the btree node cache.
This causes inode_to_wb(inode) to refer to a different page cache than
the caller page/folio operations such like __folio_start_writeback(),
__folio_end_writeback(), or __folio_mark_dirty() acquired the lock.
This patch resolves the issue by allocating and using an additional
inode to hold the page cache of btree nodes. The inode is attached
one-to-one to the traditional nilfs2 inode if it requires a block
mapping with b-tree. This setup change is in memory only and does not
affect the disk format.
==================================================================
BUG: KASAN: stack-out-of-bounds in unwind_frame+0x508/0x870
Read of size 4 at addr c36bba90 by task cat/163
addr c36bba90 is located in stack of task cat/163 at offset 48 in frame:
stack_trace_save+0x0/0xb4
this frame has 1 object:
[32, 48) 'trace'
Memory state around the buggy address: c36bb980: f1 f1 f1 f1 00 04 f2 f2 00 00 f3 f3 00 00 00 00 c36bba00: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
>c36bba80: 00 00 f3 f3 00 00 00 00 00 00 00 00 00 00 00 00
^ c36bbb00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c36bbb80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
There is a same issue on x86 and has been resolved by the commit f7d27c35ddff
("x86/mm, kasan: Silence KASAN warnings in get_wchan()").
The solution could be applied to arm architecture too.
Signed-off-by: Lin Yujun <linyujun809@huawei.com> Reported-by: He Ying <heying24@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Debugfs console_log uses devm memory (e.g. debug_info in
cros_ec_console_log_poll()). However, lifecycles of device and debugfs
are independent. An use-after-free issue is observed if userland
program operates the debugfs after the memory has been freed.
The call trace:
do_raw_spin_lock
_raw_spin_lock_irqsave
remove_wait_queue
ep_unregister_pollwait
ep_remove
do_epoll_ctl
A Python example to reproduce the issue:
... import select
... p = select.epoll()
... f = open('/sys/kernel/debug/cros_scp/console_log')
... p.register(f, select.POLLIN)
... p.poll(1)
[(4, 1)] # 4=fd, 1=select.POLLIN
kzalloc() is a memory allocation function which can return NULL when
some internal memory errors happen. So it is better to check the
return value of it to prevent potential wrong memory access or
memory leak.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting the century forward has been failing on AMD platforms.
There was a previous attempt at fixing this for family 0x17 as part of
commit 7ad295d5196a ("rtc: Fix the AltCentury value on AMD/Hygon
platform") but this was later reverted due to some problems reported
that appeared to stem from an FW bug on a family 0x17 desktop system.
The same comments mentioned in the previous commit continue to apply
to the newer platforms as well.
```
MC146818 driver use function mc146818_set_time() to set register
RTC_FREQ_SELECT(RTC_REG_A)'s bit4-bit6 field which means divider stage
reset value on Intel platform to 0x7.
While AMD/Hygon RTC_REG_A(0Ah)'s bit4 is defined as DV0 [Reference]:
DV0 = 0 selects Bank 0, DV0 = 1 selects Bank 1. Bit5-bit6 is defined
as reserved.
DV0 is set to 1, it will select Bank 1, which will disable AltCentury
register(0x32) access. As UEFI pass acpi_gbl_FADT.century 0x32
(AltCentury), the CMOS write will be failed on code:
CMOS_WRITE(century, acpi_gbl_FADT.century).
Correct RTC_REG_A bank select bit(DV0) to 0 on AMD/Hygon CPUs, it will
enable AltCentury(0x32) register writing and finally setup century as
expected.
```
However in closer examination the change previously submitted was also
modifying bits 5 & 6 which are declared reserved in the AMD documentation.
So instead modify just the DV0 bank selection bit.
Being cognizant that there was a failure reported before, split the code
change out to a static function that can also be used for exclusions if
any regressions such as Mikhail's pop up again.
nvme_mpath_init_identify() invoked from nvme_init_identify() fetches a
fresh ANA log from the ctrl. This is essential to have an up to date
path states for both existing namespaces and for those scan_work may
discover once the ctrl is up.
This happens in the following cases:
1) A new ctrl is being connected.
2) An existing ctrl is successfully reconnected.
3) An existing ctrl is being reset.
While in (1) ctrl->namespaces is empty, (2 & 3) may have namespaces, and
nvme_read_ana_log() may call nvme_update_ns_ana_state().
This result in a hang when the ANA state of an existing namespace changes
and makes the disk live: nvme_mpath_set_live() issues IO to the namespace
through the ctrl, which does NOT have IO queues yet.
See sample hang below.
Solution:
- nvme_update_ns_ana_state() to call set_live only if ctrl is live
- nvme_read_ana_log() call from nvme_mpath_init_identify()
therefore only fetches and parses the ANA log;
any erros in this process will fail the ctrl setup as appropriate;
- a separate function nvme_mpath_update()
is called in nvme_start_ctrl();
this parses the ANA log without fetching it.
At this point the ctrl is live,
therefore, disks can be set live normally.
The chacha_Nblock_xor_avx512vl() functions all have their own,
identical, .LdoneN label, however in one particular spot {2,4} jump to
the 8 version instead of their own. Resulting in:
arch/x86/crypto/chacha-x86_64.o: warning: objtool: chacha_2block_xor_avx512vl() falls through to next function chacha_8block_xor_avx512vl()
arch/x86/crypto/chacha-x86_64.o: warning: objtool: chacha_4block_xor_avx512vl() falls through to next function chacha_8block_xor_avx512vl()
Make each function consistently use its own done label.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Martin Willi <martin@strongswan.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in stm32_crc_remove, so we should fix it.
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in stmfts_input_open, so we should fix it.
The syscall_handler_t type for x86_64 was defined as 'long (*)(void)',
but always cast to 'long (*)(long, long, long, long, long, long)' before
use. This now triggers a warning (see below).
Define syscall_handler_t as the latter instead, and remove the cast.
This simplifies the code, and fixes the warning.
Warning:
In file included from ../arch/um/include/asm/processor-generic.h:13
from ../arch/x86/um/asm/processor.h:41
from ../include/linux/rcupdate.h:30
from ../include/linux/rculist.h:11
from ../include/linux/pid.h:5
from ../include/linux/sched.h:14
from ../include/linux/ptrace.h:6
from ../arch/um/kernel/skas/syscall.c:7:
../arch/um/kernel/skas/syscall.c: In function ‘handle_syscall’:
../arch/x86/um/shared/sysdep/syscalls_64.h:18:11: warning: cast between incompatible function types from ‘long int (*)(void)’ to ‘long int (*)(long int, long int, long int, long int, long int, long int)’ [
-Wcast-function-type]
18 | (((long (*)(long, long, long, long, long, long)) \
| ^
../arch/x86/um/asm/ptrace.h:36:62: note: in definition of macro ‘PT_REGS_SET_SYSCALL_RETURN’
36 | #define PT_REGS_SET_SYSCALL_RETURN(r, res) (PT_REGS_AX(r) = (res))
| ^~~
../arch/um/kernel/skas/syscall.c:46:33: note: in expansion of macro ‘EXECUTE_SYSCALL’
46 | EXECUTE_SYSCALL(syscall, regs));
| ^~~~~~~~~~~~~~~
Signed-off-by: David Gow <davidgow@google.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the irqwork is still scheduled or running while the RTC device is
removed, a use-after-free occurs in rtc_timer_do_work(). Cleanup the
timerqueue and ensure the work is stopped to fix this.
BUG: KASAN: use-after-free in mutex_lock+0x94/0x110
Write of size 8 at addr ffffff801d846338 by task kworker/3:1/41
The unwinder reports the secondary CPU idle tasks' stack on XEN PV as
unreliable, which affects at least live patching.
cpu_initialize_context() sets up the context of the CPU through
VCPUOP_initialise hypercall. After it is woken up, the idle task starts
in cpu_bringup_and_idle() function and its stack starts at the offset
right below pt_regs. The unwinder correctly detects the end of stack
there but it is confused by NULL return address in the last frame.
Introduce a wrapper in assembly, which just calls
cpu_bringup_and_idle(). The return address is thus pushed on the stack
and the wrapper contains the annotation hint for the unwinder regarding
the stack state.
Signed-off-by: Miroslav Benes <mbenes@suse.cz> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Markus Boehme <markubo@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unwinder reports the boot CPU idle task's stack on XEN PV as
unreliable, which affects at least live patching. There are two reasons
for this. First, the task does not follow the x86 convention that its
stack starts at the offset right below saved pt_regs. It allows the
unwinder to easily detect the end of the stack and verify it. Second,
startup_xen() function does not store the return address before jumping
to xen_start_kernel() which confuses the unwinder.
Amend both issues by moving the starting point of initial stack in
startup_xen() and storing the return address before the jump, which is
exactly what call instruction does.
Signed-off-by: Miroslav Benes <mbenes@suse.cz> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Markus Boehme <markubo@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupt handler bad_flp_intr() may cause a UAF on the recently freed
request just to increment the error count. There's no point keeping
that one in the request anyway, and since the interrupt handler uses a
static pointer to the error which cannot be kept in sync with the
pending request, better make it use a static error counter that's reset
for each new request. This reset now happens when entering
redo_fd_request() for a new request via set_next_request().
One initial concern about a single error counter was that errors on one
floppy drive could be reported on another one, but this problem is not
real given that the driver uses a single drive at a time, as that
PC-compatible controllers also have this limitation by using shared
signals. As such the error count is always for the "current" drive.
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
When ping_group_range is updated, 'ping' uses the DGRAM ICMP socket,
instead of an IP raw socket. In this case, 'ping' is unable to bind its
socket to a local address owned by a vrflite.
Before the patch:
$ sysctl -w net.ipv4.ping_group_range='0 2147483647'
$ ip link add blue type vrf table 10
$ ip link add foo type dummy
$ ip link set foo master blue
$ ip link set foo up
$ ip addr add 192.168.1.1/24 dev foo
$ ip addr add 2001::1/64 dev foo
$ ip vrf exec blue ping -c1 -I 192.168.1.1 192.168.1.2
ping: bind: Cannot assign requested address
$ ip vrf exec blue ping6 -c1 -I 2001::1 2001::2
ping6: bind icmp socket: Cannot assign requested address
CC: stable@vger.kernel.org Fixes: 1b69c6d0ae90 ("net: Introduce L3 Master device abstraction") Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The semantics of pfn_valid() is to check presence of the memory map for a
PFN and not whether a PFN is covered by the linear map. The memory map
may be present for NOMAP memory regions, but they won't be mapped in the
linear mapping. Accessing such regions via __va() when they are
memremap()'ed will cause a crash.
On v5.4.y the crash happens on qemu-arm with UEFI [1]:
<1>[ 0.084476] 8<--- cut here ---
<1>[ 0.084595] Unable to handle kernel paging request at virtual address dfb76000
<1>[ 0.084938] pgd = (ptrval)
<1>[ 0.085038] [dfb76000] *pgd=5f7fe801, *pte=00000000, *ppte=00000000
...
<4>[ 0.093923] [<c0ed6ce8>] (memcpy) from [<c16a06f8>] (dmi_setup+0x60/0x418)
<4>[ 0.094204] [<c16a06f8>] (dmi_setup) from [<c16a38d4>] (arm_dmi_init+0x8/0x10)
<4>[ 0.094408] [<c16a38d4>] (arm_dmi_init) from [<c0302e9c>] (do_one_initcall+0x50/0x228)
<4>[ 0.094619] [<c0302e9c>] (do_one_initcall) from [<c16011e4>] (kernel_init_freeable+0x15c/0x1f8)
<4>[ 0.094841] [<c16011e4>] (kernel_init_freeable) from [<c0f028cc>] (kernel_init+0x8/0x10c)
<4>[ 0.095057] [<c0f028cc>] (kernel_init) from [<c03010e8>] (ret_from_fork+0x14/0x2c)
On kernels v5.10.y and newer the same crash won't reproduce on ARM because
commit b10d6bca8720 ("arch, drivers: replace for_each_membock() with
for_each_mem_range()") changed the way memory regions are registered in
the resource tree, but that merely covers up the problem.
On ARM64 memory resources registered in yet another way and there the
issue of wrong usage of pfn_valid() to ensure availability of the linear
map is also covered.
Implement arch_memremap_can_ram_remap() on ARM and ARM64 to prevent access
to NOMAP regions via the linear mapping in memremap().
Link: https://lore.kernel.org/all/Yl65zxGgFzF1Okac@sirena.org.uk Link: https://lkml.kernel.org/r/20220426060107.7618-1-rppt@kernel.org Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Reported-by: "kernelci.org bot" <bot@kernelci.org> Tested-by: Mark Brown <broonie@kernel.org> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Mark Brown <broonie@kernel.org> Cc: Mark-PK Tsai <mark-pk.tsai@mediatek.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Tony Lindgren <tony@atomide.com> Cc: Will Deacon <will@kernel.org> Cc: <stable@vger.kernel.org> [5.4+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following error caused by a race condition between
phydev->adjust_link() and a MDIO transaction in the phy interrupt
handler. The issue was reproduced with the ethernet FEC driver and a
micrel KSZ9031 phy.
[ 146.195696] fec 2188000.ethernet eth0: MDIO read timeout
[ 146.201779] ------------[ cut here ]------------
[ 146.206671] WARNING: CPU: 0 PID: 571 at drivers/net/phy/phy.c:942 phy_error+0x24/0x6c
[ 146.214744] Modules linked in: bnep imx_vdoa imx_sdma evbug
[ 146.220640] CPU: 0 PID: 571 Comm: irq/128-2188000 Not tainted 5.18.0-rc3-00080-gd569e86915b7 #9
[ 146.229563] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 146.236257] unwind_backtrace from show_stack+0x10/0x14
[ 146.241640] show_stack from dump_stack_lvl+0x58/0x70
[ 146.246841] dump_stack_lvl from __warn+0xb4/0x24c
[ 146.251772] __warn from warn_slowpath_fmt+0x5c/0xd4
[ 146.256873] warn_slowpath_fmt from phy_error+0x24/0x6c
[ 146.262249] phy_error from kszphy_handle_interrupt+0x40/0x48
[ 146.268159] kszphy_handle_interrupt from irq_thread_fn+0x1c/0x78
[ 146.274417] irq_thread_fn from irq_thread+0xf0/0x1dc
[ 146.279605] irq_thread from kthread+0xe4/0x104
[ 146.284267] kthread from ret_from_fork+0x14/0x28
[ 146.289164] Exception stack(0xe6fa1fb0 to 0xe6fa1ff8)
[ 146.294448] 1fa0: 00000000000000000000000000000000
[ 146.302842] 1fc0: 0000000000000000000000000000000000000000000000000000000000000000
[ 146.311281] 1fe0: 000000000000000000000000000000000000001300000000
[ 146.318262] irq event stamp: 12325
[ 146.321780] hardirqs last enabled at (12333): [<c01984c4>] __up_console_sem+0x50/0x60
[ 146.330013] hardirqs last disabled at (12342): [<c01984b0>] __up_console_sem+0x3c/0x60
[ 146.338259] softirqs last enabled at (12324): [<c01017f0>] __do_softirq+0x2c0/0x624
[ 146.346311] softirqs last disabled at (12319): [<c01300ac>] __irq_exit_rcu+0x138/0x178
[ 146.354447] ---[ end trace 0000000000000000 ]---
With the FEC driver phydev->adjust_link() calls fec_enet_adjust_link()
calls fec_stop()/fec_restart() and both these function reset and
temporary disable the FEC disrupting any MII transaction that
could be happening at the same time.
fec_enet_adjust_link() and phy_read() can be running at the same time
when we have one additional interrupt before the phy_state_machine() is
able to terminate.
Sudip Mukherjee [Sat, 14 May 2022 15:47:30 +0000 (16:47 +0100)]
MIPS: fix build with gcc-12
Some mips builds with gcc-12 fails with the error:
arch/mips/jz4740/setup.c:64:25: error: comparison between two arrays
[-Werror=array-compare]
64 | if (__dtb_start != __dtb_end)
'd24f48767d5e ("MIPS: Use address-of operator on section symbols")' has
been applied which fixes most of the error, but it missed one file which
was not available upstream when the change was done.
Fixes: d24f48767d5e ("MIPS: Use address-of operator on section symbols") Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Transition to drm_mode_fb_cmd2 from drm_mode_fb_cmd left the structure
unitialized. drm_mode_fb_cmd2 adds a few additional members, e.g. flags
and modifiers which were never initialized. Garbage in those members
can cause random failures during the bringup of the fbcon.
Initializing the structure fixes random blank screens after bootup due
to flags/modifiers mismatches during the fbcon bring up.
There are 3 places where the cpu and node masks of the top cpuset can
be initialized in the order they are executed:
1) start_kernel -> cpuset_init()
2) start_kernel -> cgroup_init() -> cpuset_bind()
3) kernel_init_freeable() -> do_basic_setup() -> cpuset_init_smp()
The first cpuset_init() call just sets all the bits in the masks.
The second cpuset_bind() call sets cpus_allowed and mems_allowed to the
default v2 values. The third cpuset_init_smp() call sets them back to
v1 values.
For systems with cgroup v2 setup, cpuset_bind() is called once. As a
result, cpu and memory node hot add may fail to update the cpu and node
masks of the top cpuset to include the newly added cpu or node in a
cgroup v2 environment.
For systems with cgroup v1 setup, cpuset_bind() is called again by
rebind_subsystem() when the v1 cpuset filesystem is mounted as shown
in the dmesg log below with an instrumented kernel.
[ 2.609781] cpuset_bind() called - v2 = 1
[ 3.079473] cpuset_init_smp() called
[ 7.103710] cpuset_bind() called - v2 = 0
smp_init() is called after the first two init functions. So we don't
have a complete list of active cpus and memory nodes until later in
cpuset_init_smp() which is the right time to set up effective_cpus
and effective_mems.
To fix this cgroup v2 mask setup problem, the potentially incorrect
cpus_allowed & mems_allowed setting in cpuset_init_smp() are removed.
For cgroup v2 systems, the initial cpuset_bind() call will set the masks
correctly. For cgroup v1 systems, the second call to cpuset_bind()
will do the right setup.
The bug is here:
ret = i40e_add_macvlan_filter(hw, ch->seid, vdev->dev_addr, &aq_err);
The list iterator 'ch' will point to a bogus position containing
HEAD if the list is empty or no element is found. This case must
be checked before any use of the iterator, otherwise it will
lead to a invalid memory access.
To fix this bug, use a new variable 'iter' as the list iterator,
while use the origin variable 'ch' as a dedicated pointer to
point to the found element.
Cc: stable@vger.kernel.org Fixes: 1d8d80b4e4ff6 ("i40e: Add macvlan support on i40e") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220510204846.2166999-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if some IOMMU has registered itself on the platform "bus", that
doesn't necessarily mean it provides translation for the device we
care about. Replace iommu_present() with a more appropriate check.
On MediaTek SoCs, the UART IP is 16550A compatible, but there are some
specific quirks: we are declaring a register shift of 2, but this is
only valid for the majority of the registers, as there are some that
are out of the standard layout.
Specifically, this driver is using definitions from serial_reg.h, where
we have a UART_EFR register defined as 2: this results in a 0x8 offset,
but there we have the FCR register instead.
The right offset for the EFR register on MediaTek UART is at 0x98,
so, following the decimal definition convention in serial_reg.h and
accounting for the register left shift of two, add and use the correct
register address for this IP, defined as decimal 38, so that the final
calculation results in (0x26 << 2) = 0x98.
platform_get_irq() returns non-zero IRQ number on success,
negative error number on failure.
And the doc of platform_get_irq() provides a usage example:
int irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
Fix the check of return value to catch errors correctly.
The MA510 modem has 3 USB configurations that are configurable via the AT
command AT+GTUSBMODE={30,31,32} which make the modem enumerate with the
following interfaces, respectively:
The L610 modem has 3 USB configurations that are configurable via the AT
command AT+GTUSBMODE={31,32,33} which make the modem enumerate with the
following interfaces, respectively:
31: Modem + NV + MOS + Diag + LOG + AT + AT
32: ECM + Modem + NV + MOS + Diag + LOG + AT + AT
33: RNDIS + Modem + NV + MOS + Diag + LOG + AT + AT
A detailed description of the USB configuration for each mode follows:
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
In this case the remove callback even returns early without stopping the
tcpm worker thread and various timers. A work scheduled on the work
queue, or a firing timer after tcpci_remove() returned probably results
in a use-after-free situation because the regmap and driver data were
freed. So better make sure that tcpci_unregister_port() is called even
if disabling the irq failed.
Also emit a more specific error message instead of the i2c core's
"remove failed (EIO), will be ignored" and return 0 to suppress the
core's warning.
This patch is (also) a preparation for making i2c remove callbacks
return void.
cdc-wdm tracks whether a response reading request is in-progress and
blocks the next request from being sent until the previous request is
completed. As soon as last user closes the cdc-wdm device file, the
driver cancels any ongoing requests, resets the pending response
counter, but leaves the response reading in-progress flag
(WDM_RESPONDING) untouched.
So if the user closes the device file during the response receive
request is being performed, no more data will be obtained from the
modem. The request will be cancelled, effectively preventing the
WDM_RESPONDING flag from being reseted. Keeping the flag set will
prevent a new response receive request from being sent, permanently
blocking the read path. The read path will staying blocked until the
module will be reloaded or till the modem will be re-attached.
This stuck has been observed with a Huawei E3372 modem attached to an
OpenWrt router and using the comgt utility to set up a network
connection.
Fix this issue by clearing the WDM_RESPONDING flag on the device file
close.
Without this fix, the device reading stuck can be easily reproduced in a
few connection establishing attempts. With this fix, a load test for
modem connection re-establishing worked for several hours without any
issues.
Fixes: 922a5eadd5a3 ("usb: cdc-wdm: Fix race between autosuspend and reading from the device") Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> Cc: stable <stable@vger.kernel.org> Acked-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20220501175828.8185-1-ryazanov.s.a@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation activates the mux if it was restarted and opens
the control channel if the mux was previously closed and we are now acting
as initiator instead of responder, which is the default setting.
This has two issues.
1) No mux is activated if we keep all default values and only switch to
initiator. The control channel is not allocated but will be opened next
which results in a NULL pointer dereference.
2) Switching the configuration after it was once configured while keeping
the initiator value the same will not reopen the control channel if it was
closed due to parameter incompatibilities. The mux remains dead.
Fix 1) by always activating the mux if it is dead after configuration.
Fix 2) by always opening the control channel after mux activation.
In order to limit the ability for an observer to recognize the source
ports sequence used to contact a set of destinations, we should
periodically shuffle the secret. 10 seconds looks effective enough
without causing particular issues.
Cc: Moshe Kol <moshe.kol@mail.huji.ac.il> Cc: Yossi Gilad <yossi.gilad@mail.huji.ac.il> Cc: Amit Klein <aksecurity@gmail.com> Cc: Jason A. Donenfeld <Jason@zx2c4.com> Tested-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In xemaclite_open() function we are setting the max speed of
emaclite to 100Mb using phy_set_max_speed() function so,
there is no need to write the advertising registers to stop
giga-bit speed and the phy_start() function starts the
auto-negotiation so, there is no need to handle it separately
using advertising registers. Remove the phy_read and phy_write
of advertising registers in xemaclite_open() function.
gcc-12 shows a lot of array bound warnings on s390. This is caused
by the S390_lowcore macro which uses a hardcoded address of 0.
Wrapping that with absolute_pointer() works, but gcc no longer knows
that a 12 bit displacement is sufficient to access lowcore. So it
emits instructions like 'lghi %r1,0; l %rx,xxx(%r1)' instead of a
single load/store instruction. As s390 stores variables often
read/written in lowcore, this is considered problematic. Therefore
disable -Warray-bounds on s390 for gcc-12 for the time being, until
there is a better solution.
Check that values written via snd_soc_put_volsw_range() are
within the range advertised by the control, ensuring that we
don't write out of spec values to the hardware.
The max98090 driver has some custom controls which share a put() function
which returns 0 unconditionally, meaning that events are not generated
when the value changes. Fix that.
The max98090 driver has a custom put function for some controls which can
only be updated in certain circumstances which makes no effort to validate
that input is suitable for the control, allowing out of spec values to be
written to the hardware and presented to userspace. Fix this by returning
an error when invalid values are written.
All temperature of Fintek superio hwmonitor that using 1-byte reg will use
2's complement.
In show_temp()
temp = data->temp[nr] * 1000;
When data->temp[nr] read as 255, it indicate -1C, but this code will report
255C to userspace. It'll be ok when change to:
temp = ((s8)data->temp[nr]) * 1000;
When a write cannot be carried out in full, gfs2_iomap_end() releases
blocks that have been allocated for this write but haven't been used.
To compute the end of the allocation, gfs2_iomap_end() incorrectly
rounded the end of the attempted write down to the next block boundary
to arrive at the end of the allocation. It would have to round up, but
the end of the allocation is also available as iomap->offset +
iomap->length, so just use that instead.
In addition, use round_up() for computing the start of the unused range.
In the NIC ->probe() callback, ->mtd_probe() callback is called.
If NIC has 2 ports, ->probe() is called twice and ->mtd_probe() too.
In the ->mtd_probe(), which is efx_ef10_mtd_probe() it allocates and
initializes mtd partiion.
But mtd partition for sfc is shared data.
So that allocated mtd partition data from last called
efx_ef10_mtd_probe() will not be used.
Therefore it must be freed.
But it doesn't free a not used mtd partition data in efx_ef10_mtd_probe().
Non blocking sendmsg will return -EAGAIN when any signal pending
and no send space left, while non blocking recvmsg return -EINTR
when signal pending and no data received. This may makes confused.
As TCP returns -EAGAIN in the conditions described above. Align the
behavior of smc with TCP.
Fixes: 846e344eb722 ("net/smc: add receive timeout check") Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/20220512030820.73848-1-guangguan.wang@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently pedit tries to ensure that the accessed skb offset
is writable via skb_unclone(). The action potentially allows
touching any skb bytes, so it may end-up modifying shared data.
The above causes some sporadic MPTCP self-test failures, due to
this code:
The above modifies a data byte outside the skb head and the skb is
a cloned one, carrying a TCP output packet.
This change addresses the issue by keeping track of a rough
over-estimate highest skb offset accessed by the action and ensuring
such offset is really writable.
Note that this may cause performance regressions in some scenarios,
but hopefully pedit is not in the critical path.
Fixes: db2c24175d14 ("act_pedit: access skb->data safely") Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Tested-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/1fcf78e6679d0a287dd61bb0f04730ce33b3255d.1652194627.git.pabeni@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log