We are seeing an IRQ storm on the global receive IRQ line under heavy
CAN bus load conditions with both CAN channels enabled.
Conditions:
The global receive IRQ line is shared between can0 and can1, either of
the channels can trigger interrupt while the other channel's IRQ line
is disabled (RFIE).
When global a receive IRQ interrupt occurs, we mask the interrupt in
the IRQ handler. Clearing and unmasking of the interrupt is happening
in rx_poll(). There is a race condition where rx_poll() unmasks the
interrupt, but the next IRQ handler does not mask the IRQ due to
NAPIF_STATE_MISSED flag (e.g.: can0 RX FIFO interrupt is disabled and
can1 is triggering RX interrupt, the delay in rx_poll() processing
results in setting NAPIF_STATE_MISSED flag) leading to an IRQ storm.
This patch fixes the issue by checking IRQ active and enabled before
handling the IRQ on a particular channel.
Fixes: dd3bd23eb438 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver") Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/all/20221025155657.1426948-2-biju.das.jz@bp.renesas.com Cc: stable@vger.kernel.org
[mkl: adjust commit message] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[biju: removed gpriv from RCANFD_RFCC_RFIE macro] Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under memory pressure, enetc_refill_rx_ring() may fail, and when called
during the enetc_open() -> enetc_setup_rxbdr() procedure, this is not
checked for.
An extreme case of memory pressure will result in exactly zero buffers
being allocated for the RX ring, and in such a case it is expected that
hardware drops all RX packets due to lack of buffers.
This does not happen, because the reset-default value of the consumer
and produces index is 0, and this makes the ENETC think that all buffers
have been initialized and that it owns them (when in reality none were).
The hardware guide explains this best:
| Configure the receive ring producer index register RBaPIR with a value
| of 0. The producer index is initially configured by software but owned
| by hardware after the ring has been enabled. Hardware increments the
| index when a frame is received which may consume one or more BDs.
| Hardware is not allowed to increment the producer index to match the
| consumer index since it is used to indicate an empty condition. The ring
| can hold at most RBLENR[LENGTH]-1 received BDs.
|
| Configure the receive ring consumer index register RBaCIR. The
| consumer index is owned by software and updated during operation of the
| of the BD ring by software, to indicate that any receive data occupied
| in the BD has been processed and it has been prepared for new data.
| - If consumer index and producer index are initialized to the same
| value, it indicates that all BDs in the ring have been prepared and
| hardware owns all of the entries.
| - If consumer index is initialized to producer index plus N, it would
| indicate N BDs have been prepared. Note that hardware cannot start if
| only a single buffer is prepared due to the restrictions described in
| (2).
| - Software may write consumer index to match producer index anytime
| while the ring is operational to indicate all received BDs prior have
| been processed and new BDs prepared for hardware.
Normally, the value of rx_ring->rcir (consumer index) is brought in sync
with the rx_ring->next_to_use software index, but this only happens if
page allocation ever succeeded.
When PI==CI==0, the hardware appears to receive frames and write them to
DMA address 0x0 (?!), then set the READY bit in the BD.
The enetc_clean_rx_ring() function (and its XDP derivative) is naturally
not prepared to handle such a condition. It will attempt to process
those frames using the rx_swbd structure associated with index i of the
RX ring, but that structure is not fully initialized (enetc_new_page()
does all of that). So what happens next is undefined behavior.
To operate using no buffer, we must initialize the CI to PI + 1, which
will block the hardware from advancing the CI any further, and drop
everything.
The issue was seen while adding support for zero-copy AF_XDP sockets,
where buffer memory comes from user space, which can even decide to
supply no buffers at all (example: "xdpsock --txonly"). However, the bug
is present also with the network stack code, even though it would take a
very determined person to trigger a page allocation failure at the
perfect time (a series of ifup/ifdown under memory pressure should
eventually reproduce it given enough retries).
Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20221027182925.3256653-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
mlx5_cmd_cleanup_async_ctx should return only after all its callback
handlers were completed. Before this patch, the below race between
mlx5_cmd_cleanup_async_ctx and mlx5_cmd_exec_cb_handler was possible and
lead to a use-after-free:
1. mlx5_cmd_cleanup_async_ctx is called while num_inflight is 2 (i.e.
elevated by 1, a single inflight callback).
2. mlx5_cmd_cleanup_async_ctx decreases num_inflight to 1.
3. mlx5_cmd_exec_cb_handler is called, decreases num_inflight to 0 and
is about to call wake_up().
4. mlx5_cmd_cleanup_async_ctx calls wait_event, which returns
immediately as the condition (num_inflight == 0) holds.
5. mlx5_cmd_cleanup_async_ctx returns.
6. The caller of mlx5_cmd_cleanup_async_ctx frees the mlx5_async_ctx
object.
7. mlx5_cmd_exec_cb_handler goes on and calls wake_up() on the freed
object.
Fix it by syncing using a completion object. Mark it completed when
num_inflight reaches 0.
Trace:
BUG: KASAN: use-after-free in do_raw_spin_lock+0x23d/0x270
Read of size 4 at addr ffff888139cd12f4 by task swapper/5/0
An offloaded SA stops receiving after about 2^32 + replay_window
packets. For example, when SA reaches <seq-hi 0x1, seq 0x2c>, all
subsequent packets get dropped with SA-icv-failure (integrity_failed).
To reproduce the bug:
- ConnectX-6 Dx with crypto enabled (FW 22.30.1004)
- ipsec.conf:
nic-offload = yes
replay-window = 32
esn = yes
salifetime=24h
- Run netperf for a long time to send more than 2^32 packets
netperf -H <device-under-test> -t TCP_STREAM -l 20000
When 2^32 + replay_window packets are received, the replay window
moves from the 2nd half of subspace (overlap=1) to the 1st half
(overlap=0). The driver then updates the 'esn' value in NIC
(i.e. seq_hi) as follows.
seq_hi = xfrm_replay_seqhi(seq_bottom)
new esn in NIC = seq_hi + 1
The +1 increment is wrong, as seq_hi already contains the correct
seq_hi. For example, when seq_hi=1, the driver actually tells NIC to
use seq_hi=2 (esn). This incorrect esn value causes all subsequent
packets to fail integrity checks (SA-icv-failure). So, do not
increment.
Fixes: cb01008390bb ("net/mlx5: IPSec, Add support for ESN") Signed-off-by: Hyong Youb Kim <hyonkim@cisco.com> Acked-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Link: https://lore.kernel.org/r/20221026135153.154807-2-saeed@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As explained by Julian, fib_nh_scope is related to fib_nh_gw4, but
fib_info_update_nhc_saddr() needs the scope of the route, which is
the scope "before" fib_nh_scope, ie fib_nh_scope - 1.
This patch fixes the problem described in commit 747c14307214 ("ip: fix
dflt addr selection for connected nexthop").
Fixes: 597cfe4fc339 ("nexthop: Add support for IPv4 nexthops") Link: https://lore.kernel.org/netdev/6c8a44ba-c2d5-cdf-c5c7-5baf97cba38@ssi.bg/ Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If of_device_register() returns error, the of node and the
name allocated in dev_set_name() is leaked, call put_device()
to give up the reference that was set in device_initialize(),
so that of node is put in logical_port_release() and the name
is freed in kobject_cleanup().
As noted by Paolo Abeni, pr_warn doesn't generate any splat and can still
preserve the warning to the user that feature downgrade occurred. We
likely cannot introduce other kinds of checks / enforcement here because
syzbot can generate different genl versions to the datapath.
Reported-by: syzbot+31cde0bef4bbf8ba2d86@syzkaller.appspotmail.com Fixes: 44da5ae5fbea ("openvswitch: Drop user features if old user space attempted to create datapath") Cc: Thomas Graf <tgraf@suug.ch> Signed-off-by: Aaron Conole <aconole@redhat.com> Acked-by: Ilya Maximets <i.maximets@ovn.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
i2sbus_add_dev() is supposed to return the number of probed devices,
i.e. either 1 or 0. However, i2sbus_add_dev() has one error handling
that returns -ENODEV; this will screw up the accumulation number
counted in the caller, i2sbus_probe().
Fix the return value to 0 and add the comment for better understanding
for readers.
dev_set_name() in soundbus_add_one() allocates memory for name, it need be
freed when of_device_register() fails, call soundbus_dev_put() to give up
the reference that hold in device_initialize(), so that it can be freed in
kobject_cleanup() when the refcount hit to 0. And other resources are also
freed in i2sbus_release_dev(), so it can return 0 directly.
Platforms can provide the information about the availability of each
idle states via status flag. Platforms may have to disable one or more
idle states for various reasons like broken firmware or other unmet
dependencies.
Fix handling of such unavailable/disabled idle states by ignoring them
while parsing the states.
Fixes: a3381e3a65cb ("PM / domains: Fix up domain-idle-states OF parsing") Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
while unbinding device.
Fix setting bits for specific flow_type for GLQF_HASH_INSET register.
In previous version all of the bits were set only in hena register, while
in inset only one bit was set. In order for this working correctly on all
types of cards these bits needs to be set correctly for both hena and inset
registers.
Fixes: eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters") Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-3-jacob.e.keller@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a reset was triggered on one VF with i40e_reset_vf
global PF state __I40E_VF_DISABLE was set on a PF until
the reset finished. If immediately after triggering reset
on one VF there is a request to reset on another
it will cause a hang on VF side because VF will be notified
of incoming reset but the reset will never happen because
of this global state, we will get such error message:
[ +4.890195] iavf 0000:86:02.1: Never saw reset
and VF will hang waiting for the reset to be triggered.
Fix this by introducing new VF state I40E_VF_STATE_RESETTING
that will be set on a VF if it is currently resetting instead of
the global __I40E_VF_DISABLE PF state.
Fixes: 3ba9bcb4b68f ("i40e: add locking around VF reset") Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-2-jacob.e.keller@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
the driver would fail to setup this setting on X722
device since it was using the mask on the register
dedicated for X710 devices.
Apply a different mask on the register when setting the
RSS hash for the X722 device.
When displaying the flow types enabled via ethtool:
ethtool -n $pf rx-flow-hash tcp4|tcp6|udp4|udp6
the driver would print wrong values for X722 device.
Fix this issue by testing masks for X722 device in
i40e_get_rss_hash_opts function.
Fixes: eb0dd6e4a3b3 ("i40e: Allow RSS Hash set with less than four parameters") Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com> Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20221024100526.1874914-1-jacob.e.keller@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
VIDIOC_S_FBUF is by definition a scary ioctl, which is why only root
can use it. But at least check if the framebuffer parameters match that
of one of the framebuffer created by vivid, and reject anything else.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Fixes: ef834f7836ec ([media] vivid: add the video capture and output parts) Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Hybrid sleep is currently hardcoded to only operate with S3 even
on systems that might not support it.
Instead of assuming this mode is what the user wants to use, for
hybrid sleep follow the setting of `mem_sleep_current` which
will respect mem_sleep_default kernel command line and policy
decisions made by the presence of the FADT low power idle bit.
Fixes: 81d45bdf8913 ("PM / hibernate: Untangle power_down()") Reported-and-tested-by: kolAflash <kolAflash@kolahilft.de> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216574 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 1149108e2fbf ("can: mscan: improve clock API use") only
adds put_clock() in mpc5xxx_can_remove() function, forgetting to add
put_clock() in the error handling code.
Fix this bug by adding put_clock() in the error handling code.
Fixes: 1149108e2fbf ("can: mscan: improve clock API use") Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/all/20221024133828.35881-1-mkl@pengutronix.de Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit fixes a bug that can cause a TCP data sender to repeatedly
defer RTOs when encountering SACK reneging.
The bug is that when we're in fast recovery in a scenario with SACK
reneging, every time we get an ACK we call tcp_check_sack_reneging()
and it can note the apparent SACK reneging and rearm the RTO timer for
srtt/2 into the future. In some SACK reneging scenarios that can
happen repeatedly until the receive window fills up, at which point
the sender can't send any more, the ACKs stop arriving, and the RTO
fires at srtt/2 after the last ACK. But that can take far too long
(O(10 secs)), since the connection is stuck in fast recovery with a
low cwnd that cannot grow beyond ssthresh, even if more bandwidth is
available.
This fix changes the logic in tcp_check_sack_reneging() to only rearm
the RTO timer if data is cumulatively ACKed, indicating forward
progress. This avoids this kind of nearly infinite loop of RTO timer
re-arming. In addition, this meets the goals of
tcp_check_sack_reneging() in handling Windows TCP behavior that looks
temporarily like SACK reneging but is not really.
Many thanks to Jakub Kicinski and Neil Spring, who reported this issue
and provided critical packet traces that enabled root-causing this
issue. Also, many thanks to Jakub Kicinski for testing this fix.
Fixes: 5ae344c949e7 ("tcp: reduce spurious retransmits due to transient SACK reneging") Reported-by: Jakub Kicinski <kuba@kernel.org> Reported-by: Neil Spring <ntspring@fb.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Tested-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/r/20221021170821.1093930-1-ncardwell.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the ops_init() interface is invoked to initialize the net, but
ops->init() fails, data is released. However, the ptr pointer in
net->gen is invalid. In this case, when nfqnl_nf_hook_drop() is invoked
to release the net, invalid address access occurs.
The process is as follows:
setup_net()
ops_init()
data = kzalloc(...) ---> alloc "data"
net_assign_generic() ---> assign "date" to ptr in net->gen
...
ops->init() ---> failed
...
kfree(data); ---> ptr in net->gen is invalid
...
ops_exit_list()
...
nfqnl_nf_hook_drop()
*q = nfnl_queue_pernet(net) ---> q is invalid
The following is the Call Trace information:
BUG: KASAN: use-after-free in nfqnl_nf_hook_drop+0x264/0x280
Read of size 8 at addr ffff88810396b240 by task ip/15855
Call Trace:
<TASK>
dump_stack_lvl+0x8e/0xd1
print_report+0x155/0x454
kasan_report+0xba/0x1f0
nfqnl_nf_hook_drop+0x264/0x280
nf_queue_nf_hook_drop+0x8b/0x1b0
__nf_unregister_net_hook+0x1ae/0x5a0
nf_unregister_net_hooks+0xde/0x130
ops_exit_list+0xb0/0x170
setup_net+0x7ac/0xbd0
copy_net_ns+0x2e6/0x6b0
create_new_namespaces+0x382/0xa50
unshare_nsproxy_namespaces+0xa6/0x1c0
ksys_unshare+0x3a4/0x7e0
__x64_sys_unshare+0x2d/0x40
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
</TASK>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 17869 Comm: syz-executor.2 Not tainted 6.1.0-rc1-syzkaller-00010-gbb1a1146467a-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
value changed: 0xffff88812971ce00 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 5859 Comm: syz-executor.3 Not tainted 6.0.0-syzkaller-12189-g19d17ab7c68b-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
Fixes: ab7ac4eb9832 ("kcm: Kernel Connection Multiplexor module") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The offset 12 (bit-rate) of EEPROM SFP DAC (passive) cables is expected
to be in the range 0x64 to 0x68. However, the 5 meter and 7 meter Molex
passive cables have the rate ceiling 0x78 at offset 12.
Add a quirk for Molex passive cables to extend the rate ceiling to 0x78.
Fixes: abf0a1c2b26a ("amd-xgbe: Add support for SFP+ modules") Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current XGBE code assumes that offset 6 of EEPROM SFP DAC (passive)
cables is NULL. However, some cables (the 5 meter and 7 meter Molex
passive cables) have non-zero data at offset 6. Fix the logic by moving
the passive cable check above the active checks, so as not to be
improperly identified as an active cable. This will fix the issue for
any passive cable that advertises 1000Base-CX in offset 6.
Fixes: abf0a1c2b26a ("amd-xgbe: Add support for SFP+ modules") Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a console stack dump is initiated with CONFIG_GCOV_PROFILE_ALL
enabled, show_trace_log_lvl() gets out of sync with the ORC unwinder,
causing the stack trace to show all text addresses as unreliable:
This happens when the compiled code for show_stack() has a single word
on the stack, and doesn't use a tail call to show_stack_log_lvl().
(CONFIG_GCOV_PROFILE_ALL=y is the only known case of this.) Then the
__unwind_start() skip logic hits an off-by-one bug and fails to unwind
all the way to the intended starting frame.
Fix it by reverting the following commit:
f1d9a2abff66 ("x86/unwind/orc: Don't skip the first frame for inactive tasks")
The original justification for that commit no longer exists. That
original issue was later fixed in a different way, with the following
commit:
f2ac57a4c49d ("x86/unwind/orc: Fix inactive tasks with stack pointer in %sp on GCC 10 compiled kernels")
Fixes: f1d9a2abff66 ("x86/unwind/orc: Don't skip the first frame for inactive tasks") Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
[jpoimboe: rewrite commit log] Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If phy_device_register() fails, phy_device_free() need be called to
put refcount, so memory of phy device and device name can be freed
in callback function.
If get_phy_device() fails, mdiobus_unregister() need be called,
or it will cause warning in mdiobus_free() and kobject is leaked.
It was caused by srv->listener that might be set to null by
tipc_topsrv_stop() in net .exit whereas it's still used in
tipc_topsrv_accept() worker.
srv->listener is protected by srv->idr_lock in tipc_topsrv_stop(), so add
a check for srv->listener under srv->idr_lock in tipc_topsrv_accept() to
avoid the null-ptr-deref. To ensure the lsock is not released during the
tipc_topsrv_accept(), move sock_release() after tipc_topsrv_work_stop()
where it's waiting until the tipc_topsrv_accept worker to be done.
Note that sk_callback_lock is used to protect sk->sk_user_data instead of
srv->listener, and it should check srv in tipc_topsrv_listener_data_ready()
instead. This also ensures that no more tipc_topsrv_accept worker will be
started after tipc_conn_close() is called in tipc_topsrv_stop() where it
sets sk->sk_user_data to null.
Fixes: 0ef897be12b8 ("tipc: separate topology server listener socket from subcsriber sockets") Reported-by: syzbot+c5ce866a8d30f4be0651@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jon Maloy <jmaloy@redhat.com> Link: https://lore.kernel.org/r/4eee264380c409c61c6451af1059b7fb271a7e7b.1666120790.git.lucien.xin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If device_register() fails in snd_ac97_dev_register(), it should
call put_device() to give up reference, or the name allocated in
dev_set_name() is leaked.
Add 'volatile' to iounmap()'s argument to prevent build warnings.
This make it the same as other major architectures.
Placates these warnings: (12 such warnings)
../drivers/video/fbdev/riva/fbdev.c: In function 'rivafb_probe':
../drivers/video/fbdev/riva/fbdev.c:2067:42: error: passing argument 1 of 'iounmap' discards 'volatile' qualifier from pointer target type [-Werror=discarded-qualifiers]
2067 | iounmap(default_par->riva.PRAMIN);
The mode_valid field in drm_connector_helper_funcs is expected to be of
type:
enum drm_mode_status (* mode_valid) (struct drm_connector *connector,
struct drm_display_mode *mode);
The mismatched return type breaks forward edge kCFI since the underlying
function definition does not match the function hook definition.
The return type of mdp4_lvds_connector_mode_valid should be changed from
int to enum drm_mode_status.
The doc says the I²C device's name is used if devname is NULL, but
actually the I²C device driver's name is used.
Fixes: 0658293012af ("media: v4l: subdev: Add a function to set an I²C sub-device's name") Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The h->*_huge_pages counters are protected by the hugetlb_lock, but
alloc_huge_page has a corner case where it can decrement the counter
outside of the lock.
This could lead to a corrupted value of h->resv_huge_pages, which we have
observed on our systems.
Take the hugetlb_lock before decrementing h->resv_huge_pages to avoid a
potential race.
Link: https://lkml.kernel.org/r/20221017202505.0e6a4fcd@imladris.surriel.com Fixes: a88c76954804 ("mm: hugetlb: fix hugepage memory leak caused by wrong reserve count") Signed-off-by: Rik van Riel <riel@surriel.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Glen McCready <gkmccready@meta.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mounting a cgroup hierarchy with disabled controller in cgroup v1,
all available controllers will be attached.
For example, boot with cgroup_no_v1=cpu or cgroup_disable=cpu, and then
mount with "mount -t cgroup -ocpu cpu /sys/fs/cgroup/cpu", then all
enabled controllers will be attached except cpu.
Fix this by adding disabled controller check in cgroup1_parse_param().
If the specified controller is disabled, just return error with information
"Disabled controller xx" rather than attaching all the other enabled
controllers.
Fixes: f5dfb5315d34 ("cgroup: take options parsing into ->parse_monolithic()") Signed-off-by: Chen Zhou <chenzhou10@huawei.com> Reviewed-by: Zefan Li <lizefan.x@bytedance.com> Reviewed-by: Michal Koutný <mkoutny@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Luiz Capitulino <luizcap@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to this commit, if a grant mapping operation failed partially,
some of the entries in the map_ops array would be invalid, whereas all
of the entries in the kmap_ops array would be valid. This in turn would
cause the following logic in gntdev_map_grant_pages to become invalid:
for (i = 0; i < map->count; i++) {
if (map->map_ops[i].status == GNTST_okay) {
map->unmap_ops[i].handle = map->map_ops[i].handle;
if (!use_ptemod)
alloced++;
}
if (use_ptemod) {
if (map->kmap_ops[i].status == GNTST_okay) {
if (map->map_ops[i].status == GNTST_okay)
alloced++;
map->kunmap_ops[i].handle = map->kmap_ops[i].handle;
}
}
}
...
atomic_add(alloced, &map->live_grants);
Assume that use_ptemod is true (i.e., the domain mapping the granted
pages is a paravirtualized domain). In the code excerpt above, note that
the "alloced" variable is only incremented when both kmap_ops[i].status
and map_ops[i].status are set to GNTST_okay (i.e., both mapping
operations are successful). However, as also noted above, there are
cases where a grant mapping operation fails partially, breaking the
assumption of the code excerpt above.
The aforementioned causes map->live_grants to be incorrectly set. In
some cases, all of the map_ops mappings fail, but all of the kmap_ops
mappings succeed, meaning that live_grants may remain zero. This in turn
makes it impossible to unmap the successfully grant-mapped pages pointed
to by kmap_ops, because unmap_grant_pages has the following snippet of
code at its beginning:
if (atomic_read(&map->live_grants) == 0)
return; /* Nothing to do */
In other cases where only some of the map_ops mappings fail but all
kmap_ops mappings succeed, live_grants is made positive, but when the
user requests unmapping the grant-mapped pages, __unmap_grant_pages_done
will then make map->live_grants negative, because the latter function
does not check if all of the pages that were requested to be unmapped
were actually unmapped, and the same function unconditionally subtracts
"data->count" (i.e., a value that can be greater than map->live_grants)
from map->live_grants. The side effects of a negative live_grants value
have not been studied.
The net effect of all of this is that grant references are leaked in one
of the above conditions. In Qubes OS v4.1 (which uses Xen's grant
mechanism extensively for X11 GUI isolation), this issue manifests
itself with warning messages like the following to be printed out by the
Linux kernel in the VM that had granted pages (that contain X11 GUI
window data) to dom0: "g.e. 0x1234 still pending", especially after the
user rapidly resizes GUI VM windows (causing some grant-mapping
operations to partially or completely fail, due to the fact that the VM
unshares some of the pages as part of the window resizing, making the
pages impossible to grant-map from dom0).
The fix for this issue involves counting all successful map_ops and
kmap_ops mappings separately, and then adding the sum to live_grants.
During unmapping, only the number of successfully unmapped grants is
subtracted from live_grants. The code is also modified to check for
negative live_grants values after the subtraction and warn the user.
Link: https://github.com/QubesOS/qubes-issues/issues/7631 Fixes: dbe97cff7dd9 ("xen/gntdev: Avoid blocking in unmap_grant_pages()") Cc: stable@vger.kernel.org Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com> Acked-by: Demi Marie Obenour <demi@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20221002222006.2077-2-m.v.b@runbox.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While working on XSA-361 and its follow-ups, I failed to spot another
place where the kernel mapping part of an operation was not treated the
same as the user space part. Detect and propagate errors and add a 2nd
pr_debug().
Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/c2513395-74dc-aea3-9192-fd265aa44e35@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Demi Marie Obenour <demi@invisiblethingslab.com> Co-authored-by: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5833112df7e9 tried to make it so that a remap operation would
force the log out to disk if the filesystem is mounted with mandatory
synchronous writes. Unfortunately, that commit failed to handle the
case where the inode or the file descriptor require mandatory
synchronous writes.
Refactor the check into into a helper that will look for all three
conditions, and now we can treat reflink just like any other synchronous
write.
Fixes: 5833112df7e9 ("xfs: reflink should force the log out if mounted with wsync") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8d3d7e2b35ea, we changed xfs_qm_dqpurge to bail out if we
can't lock the dquot buf to flush the dquot. This prevents the AIL from
blocking on the dquot, but it also forgets to clear the FREEING flag on
its way out. A subsequent purge attempt will see the FREEING flag is
set and bail out, which leads to dqpurge_all failing to purge all the
dquots.
(copy-pasting from Dave Chinner's identical patch)
This was found by inspection after having xfs/305 hang 1 in ~50
iterations in a quotaoff operation:
Returning -EAGAIN from xfs_qm_dqpurge() without clearing the
XFS_DQ_FREEING flag means the xfs_qm_dqpurge_all() code can never
free the dquot, and we loop forever waiting for the XFS_DQ_FREEING
flag to go away on the dquot that leaked it via -EAGAIN.
Fixes: 8d3d7e2b35ea ("xfs: trylock underlying buffer on dquot flush") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Allison Collins <allison.henderson@oracle.com> Reviewed-by: Chandan Babu R <chandanrlinux@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent change to make insert range an atomic operation used the
incorrect transaction rolling mechanism. The explicit transaction
roll does not finish deferred operations. This means that intents
for rmapbt updates caused by extent shifts are not logged until the
final transaction commits. Thus if a crash occurs during an insert
range, log recovery might leave the rmapbt in an inconsistent state.
This was discovered by repeated runs of generic/455.
Update insert range to finish dfops on every shift iteration. This
is similar to collapse range and ensures that intents are logged
with the transactions that make associated changes.
Fixes: dd87f87d87fa ("xfs: rework insert range into an atomic operation") Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some exception types the instruction address points behind the
instruction that caused the exception. Take that into account and add
the missing exception table entry.
For some exception types the instruction address points behind the
instruction that caused the exception. Take that into account and add
the missing exception table entry.
For modules, names from kallsyms__parse() contain the module name which
meant that module symbols did not match exactly by name.
Fix by matching the name string up to the separating tab character.
Fixes: 1b36c03e356936d6 ("perf record: Add support for using symbols in address filters") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221026072736.2982-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzkaller managed to trigger concurrent calls to
kernfs_remove_by_name_ns() for the same file resulting in
a KASAN detected use-after-free. The race occurs when the root
node is freed during kernfs_drain().
To prevent this acquire an additional reference for the root
of the tree that is removed before calling __kernfs_remove().
Found by syzkaller with the following reproducer (slab_nomerge is
required):
The buggy address belongs to the object at ffff888008880780
which belongs to the cache kernfs_node_cache of size 128
The buggy address is located 112 bytes inside of
128-byte region [ffff888008880780, ffff888008880800)
Memory state around the buggy address: ffff888008880680: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb ffff888008880700: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
>ffff888008880780: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff888008880800: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb ffff888008880880: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
==================================================================
SDIO tuple is only allocated for standard SDIO card, especially it causes
memory corruption issues when the non-standard SDIO card has removed, which
is because the card device's reference counter does not increase for it at
sdio_init_func(), but all SDIO card device reference counter gets decreased
at sdio_release_func().
Fixes: 6f51be3d37df ("sdio: allow non-standard SDIO cards") Signed-off-by: Matthew Ma <mahongwei@zeku.com> Reviewed-by: Weizhao Ouyang <ouyangweizhao@zeku.com> Reviewed-by: John Wang <wangdayu@zeku.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221014034951.2300386-1-ouyangweizhao@zeku.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing sanity check on the bridge counter to avoid corrupting
data beyond the fixed-sized bridge array in case there are ever more
than eight bridges.
Add the missing sanity check on the bridge counter to avoid corrupting
data beyond the fixed-sized bridge array in case there are ever more
than eight bridges.
Back in 2014, the LQI was saved in the skb control buffer (skb->cb, or
mac_cb(skb)) without any actual reset of this area prior to its use.
As part of a useful rework of the use of this region, 32edc40ae65c
("ieee802154: change _cb handling slightly") introduced mac_cb_init() to
basically memset the cb field to 0. In particular, this new function got
called at the beginning of mac802154_parse_frame_start(), right before
the location where the buffer got actually filled.
What went through unnoticed however, is the fact that the very first
helper called by device drivers in the receive path already used this
area to save the LQI value for later extraction. Resetting the cb field
"so late" led to systematically zeroing the LQI.
If we consider the reset of the cb field needed, we can make it as soon
as we get an skb from a device driver, right before storing the LQI,
as is the very first time we need to write something there.
tsl2583 probe() uses devm_iio_device_register() and calling
iio_device_unregister() causes the unregister to occur twice. s
Switch to iio_device_register() instead of devm_iio_device_register()
in probe to avoid the device managed cleanup.
The iio_utils uses a digit calculation in order to know length of the
file name containing a buffer number. The digit calculation does not
work for number 0.
This leads to allocation of one character too small buffer for the
file-name when file name contains value '0'. (Eg. buffer0).
Fix digit calculation by returning one digit to be present for number
'0'.
Endpoints are normally deleted from the bandwidth list when they are
dropped, before the virt device is freed.
If xHC host is dying or being removed then the endpoints aren't dropped
cleanly due to functions returning early to avoid interacting with a
non-accessible host controller.
So check and delete endpoints that are still on the bandwidth list when
freeing the virt device.
Solves a list_del corruption kernel crash when unbinding xhci-pci,
caused by xhci_mem_cleanup() when it later tried to delete already freed
endpoints from the bandwidth list.
This only affects hosts that use software bandwidth checking, which
currenty is only the xHC in intel Panther Point PCH (Ivy Bridge)
Cc: stable@vger.kernel.org Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20221024142720.4122053-5-mathias.nyman@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally the absence of the marvell,nand-keep-config property caused
the setup_data_interface function to be provided. However when
setup_data_interface was moved into nand_controller_ops the logic was
unintentionally inverted. Update the logic so that only if the
marvell,nand-keep-config property is present the bootloader NAND config
kept.
Cc: stable@vger.kernel.org Fixes: 7a08dbaedd36 ("mtd: rawnand: Move ->setup_data_interface() to nand_controller_ops") Signed-off-by: Tony O'Brien <tony.obrien@alliedtelesis.co.nz> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20220927024728.28447-1-chris.packham@alliedtelesis.co.nz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This appears to fix the error:
"xhci_hcd <address>; ERROR Transfer event TRB DMA ptr not part of
current TD ep_index 2 comp_code 13" that appear spuriously (or pretty
often) when using a r8152 USB3 ethernet adapter with integrated hub.
ASM1042 reports as a 0.96 controller, but appears to behave more like 1.0
Inspired by this email thread: https://markmail.org/thread/7vzqbe7t6du6qsw3
When port is connected and then disconnected, the state stays as
configured. Which is incorrect as the port is no longer configured,
but in a not attached state.
The gadget driver may have a certain expectation of how the request
completion flow should be from to its configuration. Make sure the
controller driver respect that. That is, don't set IMI (Interrupt on
Missed Isoc) when usb_request->no_interrupt is set. Also, the driver
should only set IMI to the last TRB of a chain.
When servicing a transfer completion event, the dwc3 driver will reclaim
TRBs of started requests up to the request associated with the interrupt
event. Currently we don't check for interrupt due to missed isoc, and
the driver may attempt to reclaim TRBs beyond the associated event. This
causes invalid memory access when the hardware still owns the TRB. If
there's a missed isoc TRB with IMI (interrupt on missed isoc), make sure
to stop servicing further.
Note that only the last TRB of chained TRBs has its status updated with
missed isoc.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver") Cc: stable@vger.kernel.org Reported-by: Jeff Vanhoof <jdv1029@gmail.com> Reported-by: Dan Vacura <w36195@motorola.com> Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Reviewed-by: Jeff Vanhoof <jdv1029@gmail.com> Tested-by: Jeff Vanhoof <jdv1029@gmail.com> Link: https://lore.kernel.org/r/b29acbeab531b666095dfdafd8cb5c7654fbb3e1.1666735451.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA Jetson devices in Force Recovery mode (RCM) do not support
suspending, ie. flashing fails if the device has been suspended. The
devices are still visible in lsusb and seem to work otherwise, making
the issue hard to debug. This has been discovered in various forum
posts, eg. [1].
The patch has been tested on NVIDIA Jetson AGX Xavier, but I'm adding
all the Jetson models listed in [2] on the assumption that they all
behave similarly.
With char becoming unsigned by default, and with `char` alone being
ambiguous and based on architecture, signed chars need to be marked
explicitly as such. This fixes warnings like:
Instead just use del_timer_sync() which will wait for the timer to finish
before continuing. No need to check if the timer is active or not when
doing so.
This doesn't fix the race of a possible re-arming of the timer, but at
least it won't use the data that has just been freed.
kvaser_usb uses completions to signal when a response event is received
for outgoing commands.
However, it uses init_completion() to reinitialize the start_comp and
stop_comp completions before sending the start/stop commands.
In case the device sends the corresponding response just before the
actual command is sent, complete() may be called concurrently with
init_completion() which is not safe.
This might be triggerable even with a properly functioning device by
stopping the interface (CMD_STOP_CHIP) just after it goes bus-off (which
also causes the driver to send CMD_STOP_CHIP when restart-ms is off),
but that was not tested.
Fix the issue by using reinit_completion() instead.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices") Tested-by: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi> Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Link: https://lore.kernel.org/all/20221010185237.319219-2-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not allowed to call kfree_skb() from hardware interrupt context
or with interrupts being disabled. The skb is unlinked from the queue,
so it can be freed after spin_unlock_irqrestore().
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/all/20221027091237.2290111-1-yangyingliang@huawei.com Cc: stable@vger.kernel.org
[mkl: adjust subject] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On older kernels (5.4 and older), building the kernel with clang can
cause the section name to end up with "" in them, which can cause lots
of runtime issues as that is not normally a valid portion of the string.
This was fixed up in newer kernels with commit 33def8498fdd ("treewide:
Convert macro and uses of __section(foo) to __section("foo")") but
that's too heavy-handed for older kernels.
So for now, fix up the problem that commit 62c07983bef9 ("once: add
DO_ONCE_SLOW() for sleepable contexts") caused by being backported by
removing the "" characters from the section definition.
Reported-by: Oleksandr Tymoshenko <ovt@google.com> Reported-by: Yongqin Liu <yongqin.liu@linaro.org> Tested-by: Yongqin Liu <yongqin.liu@linaro.org> Cc: Naresh Kamboju <naresh.kamboju@linaro.org> Link: https://lore.kernel.org/r/20221029011211.4049810-1-ovt@google.com Link: https://lore.kernel.org/r/CAMSo37XApZ_F5nSQYWFsSqKdMv_gBpfdKG3KN1TDB+QNXqSh0A@mail.gmail.com Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Eric Dumazet <edumazet@google.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: David S. Miller <davem@davemloft.net> Cc: Sasha Levin <sashal@kernel.org> Cc: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seth Jenkins [Thu, 27 Oct 2022 15:36:52 +0000 (11:36 -0400)]
mm: /proc/pid/smaps_rollup: fix no vma's null-deref
Commit 258f669e7e88 ("mm: /proc/pid/smaps_rollup: convert to single value
seq_file") introduced a null-deref if there are no vma's in the task in
show_smaps_rollup.
Fixes: 258f669e7e88 ("mm: /proc/pid/smaps_rollup: convert to single value seq_file") Signed-off-by: Seth Jenkins <sethjenkins@google.com> Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com> Tested-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During vm boot, there might be possibility that vf registration
call comes before the vf association from host to vm.
And this might break netvsc vf path, To prevent the same block
vf registration until vf bind message comes from host.
Cc: stable@vger.kernel.org Fixes: 00d7ddba11436 ("hv_netvsc: pair VF based on serial number") Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Gaurav Kohli <gauravkohli@linux.microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey reported that the fraction of unknown filename instances in
kallsyms grew from ~0.3% to ~10% recently; Bill and Greg tracked it down
to assembler defined symbols, which regressed as a result of:
commit b8a9092330da ("Kbuild: do not emit debug info for assembly with LLVM_IAS=1")
In that commit, I allude to restoring debug info for assembler defined
symbols in a follow up patch, but it seems I forgot to do so in
commit a66049e2cf0e ("Kbuild: make DWARF version a choice")
Fixes: b8a9092330da ("Kbuild: do not emit debug info for assembly with LLVM_IAS=1") Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is very different from the upstream commit! It fixes the same
issue by adding more quirks, rather then the general fix from the 6.1
kernel, because the general fix from the 6.1 kernel is part of a larger
refactoring of the backlight code which is not suitable for the stable
series.
As described in "ACPI: video: Drop NL5x?U, PF4NU1F and PF5?U??
acpi_backlight=native quirks" (10212754a0d2) the upstream commit "ACPI:
video: Make backlight class device registration a separate step (v2)"
(3dbc80a3e4c5) makes these quirks unnecessary. However as mentioned in this
bugtracker ticket https://bugzilla.kernel.org/show_bug.cgi?id=215683#c17
the upstream fix is part of a larger patchset that is overall too complex
for stable.
The TongFang GKxNRxx, GMxNGxx, GMxZGxx, and GMxRGxx / TUXEDO
Stellaris/Polaris Gen 1-4, have the same problem as the Clevo NL5xRU and
NL5xNU / TUXEDO Aura 15 Gen1 and Gen2:
They have a working native and video interface for screen backlight.
However the default detection mechanism first registers the video interface
before unregistering it again and switching to the native interface during
boot. This results in a dangling SBIOS request for backlight change for
some reason, causing the backlight to switch to ~2% once per boot on the
first power cord connect or disconnect event. Setting the native interface
explicitly circumvents this buggy behaviour by avoiding the unregistering
process.
Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RISC-V has no sane defaults to fall back on where there is no cpu-map
in the devicetree.
Without sane defaults, the package, core and thread IDs are all set to
-1. This causes user-visible inaccuracies for tools like hwloc/lstopo
which rely on the sysfs cpu topology files to detect a system's
topology.
On a PolarFire SoC, which should have 4 harts with a thread each,
lstopo currently reports:
arm64's method of defining a default cpu topology requires only minimal
changes to apply to RISC-V also. The current arm64 implementation exits
early in a uniprocessor configuration by reading MPIDR & claiming that
uniprocessor can rely on the default values.
This is appears to be a hangover from prior to '3102bc0e6ac7 ("arm64:
topology: Stop using MPIDR for topology information")', because the
current code just assigns default values for multiprocessor systems.
With the MPIDR references removed, store_cpu_topolgy() can be moved to
the common arch_topology code.
A splat from kmem_cache_destroy() was seen with a kernel prior to
commit ee2653bbe89d ("iommu/vt-d: Remove domain and devinfo mempool")
when there was a failure in init_dmars(), because the iommu_domain
cache still had objects. While the mempool code is now gone, there
still is a leak of the si_domain memory if init_dmars() fails. So
clean up si_domain in the init_dmars() error path.
Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Will Deacon <will@kernel.org> Cc: Robin Murphy <robin.murphy@arm.com> Fixes: 86080ccc223a ("iommu/vt-d: Allocate si_domain in init_dmars()") Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20221010144842.308890-1-jsnitsel@redhat.com Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inject fault while probing module, if device_register() fails,
but the refcount of kobject is not decreased to 0, the name
allocated in dev_set_name() is leaked. Fix this by calling
put_device(), so that name can be freed in callback function
kobject_cleanup().
When the default qdisc is cake, if the qdisc of dev_queue fails to be
inited during mqprio_init(), cake_reset() is invoked to clear
resources. In this case, the tins is NULL, and it will cause gpf issue.
The process is as follows:
qdisc_create_dflt()
cake_init()
q->tins = kvcalloc(...) --->failed, q->tins is NULL
...
qdisc_put()
...
cake_reset()
...
cake_dequeue_one()
b = &q->tins[...] --->q->tins is NULL
The following is the Call Trace information:
general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:cake_dequeue_one+0xc9/0x3c0
Call Trace:
<TASK>
cake_reset+0xb1/0x140
qdisc_reset+0xed/0x6f0
qdisc_destroy+0x82/0x4c0
qdisc_put+0x9e/0xb0
qdisc_create_dflt+0x2c3/0x4a0
mqprio_init+0xa71/0x1760
qdisc_create+0x3eb/0x1000
tc_modify_qdisc+0x408/0x1720
rtnetlink_rcv_msg+0x38e/0xac0
netlink_rcv_skb+0x12d/0x3a0
netlink_unicast+0x4a2/0x740
netlink_sendmsg+0x826/0xcc0
sock_sendmsg+0xc5/0x100
____sys_sendmsg+0x583/0x690
___sys_sendmsg+0xe8/0x160
__sys_sendmsg+0xbf/0x160
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f89e5122d04
</TASK>
Fixes: 046f6fd5daef ("sched: Add Common Applications Kept Enhanced (cake) qdisc") Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When RX strap in HW is not set to MODE 3 or 4, bit 7 and 8 in CF4
register should be set. The former is already handled in
dp83867_config_init; add the latter in SGMII specific initialization.
Fixes: 2a10154abcb7 ("net: phy: dp83867: Add TI dp83867 phy") Signed-off-by: Harini Katakam <harini.katakam@amd.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Then the input contains '\0' or '\n', proc_mpc_write has read them,
so the return value needs +1.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xiaobo Liu <cppcoffee@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Under certain conditions the Magic Trackpad can group 2 reports in a
single packet. The packet is split and the raw event function is
invoked recursively for each part.
However, after processing each part, the BTN_MOUSE status is updated,
sending multiple click events. [1]
Return after processing double reports to avoid this issue.
Use a 8-byte write to initialize sub.usr_handle in
tipc_topsrv_kern_subscr(), otherwise four bytes remain uninitialized
when issuing setsockopt(..., SOL_TIPC, ...).
This resulted in an infoleak reported by KMSAN when the packet was
received:
Local variable sub created at:
tipc_topsrv_kern_subscr+0x57/0x400 net/tipc/topsrv.c:562
tipc_group_create+0x4e7/0x7d0 net/tipc/group.c:190
Bytes 84-87 of 88 are uninitialized
Memory access of size 88 starts at ffff88801ed57cd0
Data copied to user address 0000000020000400
...
=====================================================
Signed-off-by: Alexander Potapenko <glider@google.com> Fixes: 026321c6d056a5 ("tipc: rename tipc_server to tipc_topsrv") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The trial period exists until jiffies is after addr_trial_end. But as
jiffies will eventually overflow, just using time_after will eventually
give incorrect results. As the node address is set once the trial period
ends, this can be used to know that we are not in the trial period.
Fixes: e415577f57f4 ("tipc: correct discovery message handling during address trial period") Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
During backref walking, when processing a delayed reference with a type of
BTRFS_TREE_BLOCK_REF_KEY, we have two bugs there:
1) We are accessing the delayed references extent_op, and its key, without
the protection of the delayed ref head's lock;
2) If there's no extent op for the delayed ref head, we end up with an
uninitialized key in the stack, variable 'tmp_op_key', and then pass
it to add_indirect_ref(), which adds the reference to the indirect
refs rb tree.
This is wrong, because indirect references should have a NULL key
when we don't have access to the key, and in that case they should be
added to the indirect_missing_keys rb tree and not to the indirect rb
tree.
This means that if have BTRFS_TREE_BLOCK_REF_KEY delayed ref resulting
from freeing an extent buffer, therefore with a count of -1, it will
not cancel out the corresponding reference we have in the extent tree
(with a count of 1), since both references end up in different rb
trees.
When using fiemap, where we often need to check if extents are shared
through shared subtrees resulting from snapshots, it means we can
incorrectly report an extent as shared when it's no longer shared.
However this is temporary because after the transaction is committed
the extent is no longer reported as shared, as running the delayed
reference results in deleting the tree block reference from the extent
tree.
Outside the fiemap context, the result is unpredictable, as the key was
not initialized but it's used when navigating the rb trees to insert
and search for references (prelim_ref_compare()), and we expect all
references in the indirect rb tree to have valid keys.
The following reproducer triggers the second bug:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
mkfs.btrfs -f $DEV
mount -o compress $DEV $MNT
# With a compressed 128M file we get a tree height of 2 (level 1 root).
xfs_io -f -c "pwrite -b 1M 0 128M" $MNT/foo
btrfs subvolume snapshot $MNT $MNT/snap
# Fiemap should output 0x2008 in the flags column.
# 0x2000 means shared extent
# 0x8 means encoded extent (because it's compressed)
echo
echo "fiemap after snapshot, range [120M, 120M + 128K):"
xfs_io -c "fiemap -v 120M 128K" $MNT/foo
echo
# Overwrite one extent and fsync to flush delalloc and COW a new path
# in the snapshot's tree.
#
# After this we have a BTRFS_DROP_DELAYED_REF delayed ref of type
# BTRFS_TREE_BLOCK_REF_KEY with a count of -1 for every COWed extent
# buffer in the path.
#
# In the extent tree we have inline references of type
# BTRFS_TREE_BLOCK_REF_KEY, with a count of 1, for the same extent
# buffers, so they should cancel each other, and the extent buffers in
# the fs tree should no longer be considered as shared.
#
echo "Overwriting file range [120M, 120M + 128K)..."
xfs_io -c "pwrite -b 128K 120M 128K" $MNT/snap/foo
xfs_io -c "fsync" $MNT/snap/foo
# Fiemap should output 0x8 in the flags column. The extent in the range
# [120M, 120M + 128K) is no longer shared, it's now exclusive to the fs
# tree.
echo
echo "fiemap after overwrite range [120M, 120M + 128K):"
xfs_io -c "fiemap -v 120M 128K" $MNT/foo
echo
umount $MNT
Running it before this patch:
$ ./test.sh
(...)
wrote 134217728/134217728 bytes at offset 0
128 MiB, 128 ops; 0.1152 sec (1.085 GiB/sec and 1110.5809 ops/sec)
Create a snapshot of '/mnt/sdj' in '/mnt/sdj/snap'
fiemap after snapshot, range [120M, 120M + 128K):
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [245760..246015]: 34304..34559 256 0x2008
Overwriting file range [120M, 120M + 128K)...
wrote 131072/131072 bytes at offset 125829120
128 KiB, 1 ops; 0.0001 sec (683.060 MiB/sec and 5464.4809 ops/sec)
fiemap after overwrite range [120M, 120M + 128K):
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [245760..246015]: 34304..34559 256 0x2008
The extent in the range [120M, 120M + 128K) is still reported as shared
(0x2000 bit set) after overwriting that range and flushing delalloc, which
is not correct - an entire path was COWed in the snapshot's tree and the
extent is now only referenced by the original fs tree.
Running it after this patch:
$ ./test.sh
(...)
wrote 134217728/134217728 bytes at offset 0
128 MiB, 128 ops; 0.1198 sec (1.043 GiB/sec and 1068.2067 ops/sec)
Create a snapshot of '/mnt/sdj' in '/mnt/sdj/snap'
fiemap after snapshot, range [120M, 120M + 128K):
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [245760..246015]: 34304..34559 256 0x2008
Overwriting file range [120M, 120M + 128K)...
wrote 131072/131072 bytes at offset 125829120
128 KiB, 1 ops; 0.0001 sec (694.444 MiB/sec and 5555.5556 ops/sec)
fiemap after overwrite range [120M, 120M + 128K):
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [245760..246015]: 34304..34559 256 0x8
Now the extent is not reported as shared anymore.
So fix this by passing a NULL key pointer to add_indirect_ref() when
processing a delayed reference for a tree block if there's no extent op
for our delayed ref head with a defined key. Also access the extent op
only after locking the delayed ref head's lock.
The reproducer will be converted later to a test case for fstests.
Fixes: 86d5f994425252 ("btrfs: convert prelimary reference tracking to use rbtrees") Fixes: a6dbceafb915e8 ("btrfs: Remove unused op_key var from add_delayed_refs") Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When processing delayed data references during backref walking and we are
using a share context (we are being called through fiemap), whenever we
find a delayed data reference for an inode different from the one we are
interested in, then we immediately exit and consider the data extent as
shared. This is wrong, because:
1) This might be a DROP reference that will cancel out a reference in the
extent tree;
2) Even if it's an ADD reference, it may be followed by a DROP reference
that cancels it out.
In either case we should not exit immediately.
Fix this by never exiting when we find a delayed data reference for
another inode - instead add the reference and if it does not cancel out
other delayed reference, we will exit early when we call
extent_is_shared() after processing all delayed references. If we find
a drop reference, then signal the code that processes references from
the extent tree (add_inline_refs() and add_keyed_refs()) to not exit
immediately if it finds there a reference for another inode, since we
have delayed drop references that may cancel it out. In this later case
we exit once we don't have references in the rb trees that cancel out
each other and have two references for different inodes.
Running it before this patch, the extent is still listed as shared, it has
the flag 0x2000 (FIEMAP_EXTENT_SHARED) set:
$ ./test-2.sh
fiemap after cloning:
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 26624..26751 128 0x2001
fiemap after removing file bar:
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 26624..26751 128 0x2001
After this patch, after deleting bar in both tests, the extent is not
reported with the 0x2000 flag anymore, it gets only the flag 0x1
(which is FIEMAP_EXTENT_LAST):
$ ./test-1.sh
fiemap after cloning:
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 26624..26751 128 0x2001
fiemap after removing file bar:
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 26624..26751 128 0x1
$ ./test-2.sh
fiemap after cloning:
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 26624..26751 128 0x2001
fiemap after removing file bar:
/mnt/sdj/foo:
EXT: FILE-OFFSET BLOCK-RANGE TOTAL FLAGS
0: [0..127]: 26624..26751 128 0x1
These tests will later be converted to a test case for fstests.
Fixes: dc046b10c8b7d4 ("Btrfs: make fiemap not blow when you have lots of snapshots") Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.
Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.
Tested on a ThinkPad 13 1st gen with the expected results:
passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cortex-A57 and Cortex-A72 have an erratum where an interrupt that
occurs between a pair of AES instructions in aarch32 mode may corrupt
the ELR. The task will subsequently produce the wrong AES result.
The AES instructions are part of the cryptographic extensions, which are
optional. User-space software will detect the support for these
instructions from the hwcaps. If the platform doesn't support these
instructions a software implementation should be used.
Remove the hwcap bits on affected parts to indicate user-space should
not use the AES instructions.
Acked-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: James Morse <james.morse@arm.com> Link: https://lore.kernel.org/r/20220714161523.279570-3-james.morse@arm.com Signed-off-by: Will Deacon <will@kernel.org>
[florian: resolved conflicts in arch/arm64/tools/cpucaps and cpu_errata.c] Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
```
2. Ensure the guest uses 2-level device table
3. Perform VM migration which calls save/restore device tables
In that setup, we get a big "offset" between 2 device_ids,
which makes unsigned "len" round up a big positive number,
causing the scan loop to continue with a bad GPA. For example:
1. L1 table has 2 entries;
2. and we are now scanning at L2 table entry index 2075 (pointed
to by L1 first entry)
3. if next device id is 9472, we will get a big offset: 7397;
4. with unsigned 'len', 'len -= offset * esz', len will underflow to a
positive number, mistakenly into next iteration with a bad GPA;
(It should break out of the current L2 table scanning, and jump
into the next L1 table entry)
5. that bad GPA fails the guest read.
Fix it by stopping the L2 table scan when the next device id is
outside of the current table, allowing the scan to continue from
the next L1 table entry.
Thanks to Eric Auger for the fix suggestion.
Fixes: 920a7a8fa92a ("KVM: arm64: vgic-its: Add infrastructure for tableookup") Suggested-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Eric Ren <renzhengeek@gmail.com>
[maz: commit message tidy-up] Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/d9c3a564af9e2c5bf63f48a7dcbf08cd593c5c0b.1665802985.git.renzhengeek@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens because sata_pmp_init_links() initialize link->pmp up to
SATA_PMP_MAX_PORTS while em_priv is declared as 8 elements array.
I can't find the maximum Enclosure Management ports specified in AHCI
spec v1.3.1, but "12.2.1 LED message type" states that "Port Multiplier
Information" can utilize 4 bits, which implies it can support up to 16
ports. Hence, use SATA_PMP_MAX_PORTS as EM_MAX_SLOTS to resolve the
issue.
BugLink: https://bugs.launchpad.net/bugs/1970074 Cc: stable@vger.kernel.org Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'ahci:' is an invalid prefix, preventing the module from autoloading.
Fix this by using the 'platform:' prefix and DRV_NAME.
Fixes: 9e54eae23bc9 ("ahci_imx: add ahci sata support on imx platforms") Cc: stable@vger.kernel.org Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coretemp driver supports up to a hard-coded limit of 128 cores.
Today, the driver can not support a core with an ID above that limit.
Yet, the encoding of core ID's is arbitrary (BIOS APIC-ID) and so they
may be sparse and they may be large.
Update the driver to map arbitrary core ID numbers into appropriate
array indexes so that 128 cores can be supported, no matter the encoding
of core ID's.
Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Len Brown <len.brown@intel.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20221014090147.1836-3-rui.zhang@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the patch application logic checks whether the revision
needs to be applied on each logical CPU (SMT thread). Therefore, on SMT
designs where the microcode engine is shared between the two threads,
the application happens only on one of them as that is enough to update
the shared microcode engine.
However, there are microcode patches which do per-thread modification,
see Link tag below.
Therefore, drop the revision check and try applying on each thread. This
is what the BIOS does too so this method is very much tested.
Btw, change only the early paths. On the late loading paths, there's no
point in doing per-thread modification because if is it some case like
in the bugzilla below - removing a CPUID flag - the kernel cannot go and
un-use features it has detected are there early. For that, one should
use early loading anyway.
[ bp: Fixes does not contain the oldest commit which did check for
equality but that is good enough. ]
Commit b1529a41f777 "ocfs2: should reclaim the inode if
'__ocfs2_mknod_locked' returns an error" tried to reclaim the claimed
inode if __ocfs2_mknod_locked() fails later. But this introduce a race,
the freed bit may be reused immediately by another thread, which will
update dinode, e.g. i_generation. Then iput this inode will lead to BUG:
inode->i_generation != le32_to_cpu(fe->i_generation)
We could make this inode as bad, but we did want to do operations like
wipe in some cases. Since the claimed inode bit can only affect that an
dinode is missing and will return back after fsck, it seems not a big
problem. So just leave it as is by revert the reclaim logic.
Link: https://lkml.kernel.org/r/20221017130227.234480-1-joseph.qi@linux.alibaba.com Fixes: b1529a41f777 ("ocfs2: should reclaim the inode if '__ocfs2_mknod_locked' returns an error") Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reported-by: Yan Wang <wangyan122@huawei.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ocfs2_mknod(), if error occurs after dinode successfully allocated,
ocfs2 i_links_count will not be 0.
So even though we clear inode i_nlink before iput in error handling, it
still won't wipe inode since we'll refresh inode from dinode during inode
lock. So just like clear inode i_nlink, we clear ocfs2 i_links_count as
well. Also do the same change for ocfs2_symlink().
Link: https://lkml.kernel.org/r/20221017130227.234480-2-joseph.qi@linux.alibaba.com Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com> Reported-by: Yan Wang <wangyan122@huawei.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xlog_wait() on the CIL context can reference a freed context if the
waiter doesn't get scheduled before the CIL context is freed. This
can happen when a task is on the hard throttle and the CIL push
aborts due to a shutdown. This was detected by generic/019:
thread 1 thread 2
__xfs_trans_commit
xfs_log_commit_cil
<CIL size over hard throttle limit>
xlog_wait
schedule
xlog_cil_push_work
wake_up_all
<shutdown aborts commit>
xlog_cil_committed
kmem_free
remove_wait_queue
spin_lock_irqsave --> UAF
Fix it by moving the wait queue to the CIL rather than keeping it in
in the CIL context that gets freed on push completion. Because the
wait queue is now independent of the CIL context and we might have
multiple contexts in flight at once, only wake the waiters on the
push throttle when the context we are pushing is over the hard
throttle size threshold.
Fixes: 0e7ab7efe7745 ("xfs: Throttle commits on delayed background CIL push") Reported-by: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Modify fs/xfs/xfs_super.c to include the changes at locations suitable for
5.4-lts kernel ]
Move the inode dirty data flushing to a workqueue so that multiple
threads can take advantage of a single thread's flushing work. The
ratelimiting technique used in bdd4ee4 was not successful, because
threads that skipped the inode flush scan due to ratelimiting would
ENOSPC early, which caused occasional (but noticeable) changes in
behavior and sporadic fstest regressions.
Therefore, make all the writer threads wait on a single inode flush,
which eliminates both the stampeding hordes of flushers and the small
window in which a write could fail with ENOSPC because it lost the
ratelimit race after even another thread freed space.
Fixes: c6425702f21e ("xfs: ratelimit inode flush on buffered write ENOSPC") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reflink should force the log out to disk if the filesystem was mounted
with wsync, the same as most other operations in xfs.
[Note: XFS_MOUNT_WSYNC is set when the admin mounts the filesystem
with either the 'wsync' or 'sync' mount options, which effectively means
that we're classifying reflink/dedupe as IO operations and making them
synchronous when required.]
Fixes: 3fc9f5e409319 ("xfs: remove xfs_reflink_remap_range") Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Brian Foster <bfoster@redhat.com>
[darrick: add more to the changelog] Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a new helper to force the log up to the last LSN touching an
inode.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A dquot flush currently blocks on the buffer lock for the underlying
dquot buffer. In turn, this causes xfsaild to block rather than
continue processing other items in the meantime. Update
xfs_qm_dqflush() to trylock the buffer, similar to how inode buffers
are handled, and return -EAGAIN if the lock fails. Fix up any
callers that don't currently handle the error properly.
Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Acked-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Chandan Babu R <chandan.babu@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log