The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit 1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the AHCI device node was added, it was added in the wrong location
in the device tree file. The device nodes should be sorted by register
address.
Move the device node to before EHCI1, where it belongs.
Fixes: 41c64d3318aa ("ARM: dts: sun8i: r40: add sata node") Acked-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N900 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on Nokia N900 with OneNAND manufacturers: Samsung,
Numonyx.
Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT") Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com> Tested-by: Merlijn Wajer <merlijn@wizzup.org> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current set minimum voltage of 730000µV seems to be wrong. I don't
know the document which specifies that but the imx6qdl datasheets says
that the minimum voltage should be 0.925V for VDD_ARM (LDO bypassed,
lowest opp) and 1.15V for VDD_SOC (LDO bypassed, lowest opp).
Fixes: ddec5d1c0047 ("ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM") Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an off-by-one error in strncpy size argument in
tools/perf/util/map.c. The issue is that in:
strncmp(filename, "/system/lib/", 11)
the passed string literal: "/system/lib/" has 12 bytes (without the NULL
byte) and the passed size argument is 11. As a result, the logic won't
match the ending "/" byte and will pass filepaths that are stored in
other directories e.g. "/system/libmalicious/bin" or just
"/system/libmalicious".
This functionality seems to be present only on Android. I assume the
/system/ directory is only writable by the root user, so I don't think
this bug has much (or any) security impact.
Fixes: eca818369996 ("perf tools: Add automatic remapping of Android libraries") Signed-off-by: disconnect3d <dominik.b.czarnota@gmail.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Changbin Du <changbin.du@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: John Keeping <john@metanate.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Lentine <mlentine@google.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Link: http://lore.kernel.org/lkml/20200309104855.3775-1-dominik.b.czarnota@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building an arm64 defconfig with clang's integrated assembler, this error
occurs:
<instantiation>:2:2: error: unrecognized instruction mnemonic
_ASM_EXTABLE 9999b, 9f
^
arch/arm64/mm/cache.S:50:1: note: while in macro instantiation
user_alt 9f, "dc cvau, x4", "dc civac, x4", 0
^
While GNU as seems fine with case-sensitive macro instantiations, clang
doesn't, so use the actual macro name (_asm_extable) as in the rest of
the file.
Also checked that the generated assembly matches the GCC output.
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Fixes: 290622efc76e ("arm64: fix "dc cvau" cache operation on errata-affected core") Link: https://github.com/ClangBuiltLinux/linux/issues/924 Signed-off-by: Ilie Halip <ilie.halip@gmail.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it so that CEPH_MSG_DATA_PAGES data item can own pages,
fixing a bunch of memory leaks for a page vector allocated in
alloc_msg_with_page_vector(). Currently, only watch-notify
messages trigger this allocation, and normally the page vector
is freed either in handle_watch_notify() or by the caller of
ceph_osdc_notify(). But if the message is freed before that
(e.g. if the session faults while reading in the message or
if the notify is stale), we leak the page vector.
This was supposed to be fixed by switching to a message-owned
pagelist, but that never happened.
Fixes: 1907920324f1 ("libceph: support for sending notifies") Reported-by: Roman Penyaev <rpenyaev@suse.de> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Roman Penyaev <rpenyaev@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently enabling clkctrl clock on am4 can fail for RTC as the clock
parent is wrong for RTC.
Fixes: 76a1049b84dd ("clk: ti: am43xx: add new clkctrl data for am43xx") Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lkml.kernel.org/r/20200221171030.39326-1-tony@atomide.com Acked-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation")
and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it
turns out these were only necessary due to buggy hardware. This patch adds
a check for such a buggy hardware to prevent any such mistakes again.
While working further on the KS8851 driver, it came to light that the
KS8851-16MLL is capable of switching bus endianness by a hardware strap,
EESK pin. If this strap is incorrect, the IO accesses require such endian
swapping as is being reverted by this patch. Such swapping also impacts
the performance significantly.
Hence, in addition to removing it, detect that the hardware is broken,
report to user, and fail to bind with such hardware.
Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access") Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are at least 3 models of the HP x2 10 models:
Bay Trail SoC + AXP288 PMIC
Cherry Trail SoC + AXP288 PMIC
Cherry Trail SoC + TI PMIC
Like on the other HP x2 10 models we need to ignore wakeup for ACPI GPIO
events on the external embedded-controller pin to avoid spurious wakeups
on the HP x2 10 CHT + AXP288 model too.
This commit adds an extra DMI based quirk for the HP x2 10 CHT + AXP288
model, ignoring wakeups for ACPI GPIO events on the EC interrupt pin
on this model. This fixes spurious wakeups from suspend on this model.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism") Reported-and-tested-by: Marc Lehmann <schmorp@schmorp.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200302111225.6641-4-hdegoede@redhat.com Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to initialize a structure with "= {};" will not always clean out
all padding locations in a structure. So be explicit and call memset to
initialize everything for a number of bpf information structures that
are then copied from userspace, sometimes from smaller memory locations
than the size of the structure.
Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20200320162258.GA794295@kroah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the bpf syscall, we are relying on the compiler to properly zero out
the bpf_attr union that we copy userspace data into. Unfortunately that
doesn't always work properly, padding and other oddities might not be
correctly zeroed, and in some tests odd things have been found when the
stack is pre-initialized to other values.
Fix this by explicitly memsetting the structure to 0 before using it.
Reported-by: Maciej Żenczykowski <maze@google.com> Reported-by: John Stultz <john.stultz@linaro.org> Reported-by: Alexander Potapenko <glider@google.com> Reported-by: Alistair Delva <adelva@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://android-review.googlesource.com/c/kernel/common/+/1235490 Link: https://lore.kernel.org/bpf/20200320094813.GA421650@kroah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Lex 2I385SW board has two Intel I211 ethernet controllers. Without
this patch, only the first port is usable. The second port fails to
start with the following message:
igb: probe of 0000:02:00.0 failed with error -2
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Tested-by: Georg Müller <georgmueller@gmx.net> Signed-off-by: Georg Müller <georgmueller@gmx.net> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vt_in_use() dereferences console_driver->ttys[i] without proper locking.
This is broken because the tty can be closed and freed concurrently.
We could fix this by using 'READ_ONCE(console_driver->ttys[i]) != NULL'
and skipping the check of tty_struct::count. But, looking at
console_driver->ttys[i] isn't really appropriate anyway because even if
it is NULL the tty can still be in the process of being closed.
Instead, fix it by making vt_in_use() require console_lock() and check
whether the vt is allocated and has port refcount > 1. This works since
following the patch "vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use
virtual console" the port refcount is incremented while the vt is open.
Reproducer (very unreliable, but it worked for me after a few minutes):
#include <fcntl.h>
#include <linux/vt.h>
int main()
{
int fd, nproc;
struct vt_stat state;
char ttyname[16];
BUG: KASAN: use-after-free in vt_in_use drivers/tty/vt/vt_ioctl.c:48 [inline]
BUG: KASAN: use-after-free in vt_ioctl+0x1ad3/0x1d70 drivers/tty/vt/vt_ioctl.c:657
Read of size 4 at addr ffff888065722468 by task syz-vt2/132
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle") Cc: <stable@vger.kernel.org> # v3.4+ Acked-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20200322034305.210082-3-ebiggers@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VT_DISALLOCATE ioctl can free a virtual console while tty_release()
is still running, causing a use-after-free in con_shutdown(). This
occurs because VT_DISALLOCATE considers a virtual console's
'struct vc_data' to be unused as soon as the corresponding tty's
refcount hits 0. But actually it may be still being closed.
Fix this by making vc_data be reference-counted via the embedded
'struct tty_port'. A newly allocated virtual console has refcount 1.
Opening it for the first time increments the refcount to 2. Closing it
for the last time decrements the refcount (in tty_operations::cleanup()
so that it happens late enough), as does VT_DISALLOCATE.
int main()
{
if (fork()) {
for (;;)
close(open("/dev/tty5", O_RDWR));
} else {
int fd = open("/dev/tty10", O_RDWR);
for (;;)
ioctl(fd, VT_DISALLOCATE, 5);
}
}
KASAN report:
BUG: KASAN: use-after-free in con_shutdown+0x76/0x80 drivers/tty/vt/vt.c:3278
Write of size 8 at addr ffff88806a4ec108 by task syz_vt/129
Fixes: 4001d7b7fc27 ("vt: push down the tty lock so we can see what is left to tackle") Cc: <stable@vger.kernel.org> # v3.4+ Reported-by: syzbot+522643ab5729b0421998@syzkaller.appspotmail.com Acked-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20200322034305.210082-2-ebiggers@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vc_cons_allocated() checks in vt_ioctl() and vt_compat_ioctl() are
unnecessary because they can only be reached by calling ioctl() on an
open tty, which implies the corresponding virtual console is allocated.
And even if the virtual console *could* be freed concurrently, then
these checks would be broken since they aren't done under console_lock,
and the vc_data is dereferenced before them anyway.
So, remove these unneeded checks to avoid confusion.
Avoid global variables (namely sel_cons) by introducing vc_is_sel. It
checks whether the parameter is the current selection console. This will
help putting sel_cons to a struct later.
The original patch didn't copy the ieee80211_is_data() condition
because on most drivers the management frames don't go through
this path. However, they do on iwlwifi/mvm, so we do need to keep
the condition here.
Cc: stable@vger.kernel.org Fixes: ce2e1ca70307 ("mac80211: Check port authorization in the ieee80211_tx_dequeue() case") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Woody Suwalski <terraluna977@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mac80211 used to check port authorization in the Data frame enqueue case
when going through start_xmit(). However, that authorization status may
change while the frame is waiting in a queue. Add a similar check in the
dequeue case to avoid sending previously accepted frames after
authorization change. This provides additional protection against
potential leaking of frames after a station has been disconnected and
the keys for it are being removed.
net/netfilter/nft_fwd_netdev.c: In function ‘nft_fwd_netdev_eval’:
net/netfilter/nft_fwd_netdev.c:32:10: error: ‘struct sk_buff’ has no member named ‘tc_redirected’
pkt->skb->tc_redirected = 1;
^~
net/netfilter/nft_fwd_netdev.c:33:10: error: ‘struct sk_buff’ has no member named ‘tc_from_ingress’
pkt->skb->tc_from_ingress = 1;
^~
To avoid a direct dependency with tc actions from netfilter, wrap the
redirect bits around CONFIG_NET_REDIRECT and move helpers to
include/linux/skbuff.h. Turn on this toggle from the ifb driver, the
only existing client of these bits in the tree.
This patch adds skb_set_redirected() that sets on the redirected bit
on the skbuff, it specifies if the packet was redirect from ingress
and resets the timestamp (timestamp reset was originally missing in the
netfilter bugfix).
Fixes: bcfabee1afd99484 ("netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress") Reported-by: noreply@ellerman.id.au Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sd->devnode is released after calling
v4l2_subdev_release. Therefore it should be set
to NULL so that the subdev won't hold a pointer
to a released object. This fixes a reference
after free bug in function
v4l2_device_unregister_subdev
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity check in cit_get_packet_size() is not redundant as
the driver is mixing looking up altsettings by index and by number,
which may not coincide.
Fixes: 659fefa0eb17 ("V4L/DVB: gspca_xirlink_cit: Add support for camera with a bcd version of 0.01") Fixes: 59f8b0bf3c12 ("V4L/DVB: gspca_xirlink_cit: support bandwidth changing for devices with 1 alt setting") Cc: stable <stable@vger.kernel.org> # 2.6.37 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check that we have two alternate settings and at least one
endpoint before accessing the second altsetting structure and
dereferencing the endpoint arrays.
This specifically avoids dereferencing NULL-pointers or corrupting
memory when a device does not have the expected descriptors.
Note that the sanity checks in stv06xx_start() and pb0100_start() are
not redundant as the driver is mixing looking up altsettings by index
and by number, which may not coincide.
Fixes: 8668d504d72c ("V4L/DVB (12082): gspca_stv06xx: Add support for st6422 bridge and sensor") Fixes: c0b33bdc5b8d ("[media] gspca-stv06xx: support bandwidth changing") Cc: stable <stable@vger.kernel.org> # 2.6.31 Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading from a debugfs file at a nonzero position, without first reading
at position 0, leaks uninitialized memory to userspace.
It's a bit tricky to do this, since lseek() and pread() aren't allowed
on these files, and write() doesn't update the position on them. But
writing to them with splice() *does* update the position:
#define _GNU_SOURCE 1
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
int main()
{
int pipes[2], fd, n, i;
char buf[32];
pipe(pipes);
write(pipes[1], "0", 1);
fd = open("/sys/kernel/debug/fault_around_bytes", O_RDWR);
splice(pipes[0], NULL, fd, NULL, 1, 0);
n = read(fd, buf, sizeof(buf));
for (i = 0; i < n; i++)
printf("%02x", buf[i]);
printf("\n");
}
This function should not allow negative values of "wr_val". If
negatives are allowed then capping the upper bound at 7 is
meaningless. Let's make it unsigned.
Fixes: 7dc7967fc39a ("staging: kpc2000: add initial set of Daktronics drivers") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200224103325.hrxdnaeqsthplu42@kili.mountain Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on
various user requests due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: f3d27f34fdd7 ("[media] usbtv: Add driver for Fushicai USBTV007 video frame grabber") Fixes: c53a846c48f2 ("[media] usbtv: add video controls") Cc: stable <stable@vger.kernel.org> # 3.11 Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Lubomir Rintel <lkundrak@v3.sk> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking") added
an endpoint sanity check to address a NULL-pointer dereference on probe.
Unfortunately the check was done on the current altsetting which was later
changed.
Fix this by moving the sanity check to after the altsetting is changed.
Fixes: 1b976fc6d684 ("media: b2c2-flexcop-usb: add sanity checking") Cc: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling a PIO bulk transfer with highmem buffer, a temporary
mapping is assigned to urb->transfer_buffer. After the transfer is
complete, an invalid address is left behind in this pointer. This is
not ordinarily a problem since nothing touches that buffer before the
urb is released. However, when usbmon is active, usbmon_urb_complete()
calls (indirectly) mon_bin_get_data() which does access the transfer
buffer if it is set. To prevent an invalid memory access here, reset
urb->transfer_buffer to NULL when finished (musb_host_rx()), or do not
set it at all (musb_host_tx()).
Fixes: 8e8a55165469 ("usb: musb: host: Handle highmem in PIO mode") Signed-off-by: Mans Rullgard <mans@mansr.com> Cc: stable@vger.kernel.org Signed-off-by: Bin Liu <b-liu@ti.com> Link: https://lore.kernel.org/r/20200316211136.2274-8-b-liu@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL")
introduced a regression by changing the order of capability and close
settings change checks. When running with CAP_SYS_ADMIN setting the
close settings to the values already set resulted in -EOPNOTSUPP.
Fix this by changing the check order back to how it was before.
Fixes: b401f8c4f492c ("USB: cdc-acm: fix rounding error in TIOCSSERIAL") Cc: Anthony Mallet <anthony.mallet@laas.fr> Cc: stable <stable@vger.kernel.org> Cc: Oliver Neukum <oneukum@suse.com> Signed-off-by: Matthias Reichl <hias@horus.com> Link: https://lore.kernel.org/r/20200327150350.3657-1-hias@horus.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The verifier rewrote original instructions it recognized as dead code with
'goto pc-1', but reality differs from verifier simulation in that we're
actually able to trigger a hang due to hitting the 'goto pc-1' instructions.
Taking different examples to make the issue more obvious: in this example
we're probing bounds on a completely unknown scalar variable in r1:
We're first probing lower/upper bounds via jmp64, later we do a similar
check via jmp32 and examine the resulting var_off there. After fall-through
in insn 14, we get the following bounded r1 with 0x7fffffffff unknown marked
bits in the variable section.
Thus, after knowing r1 <= 0x4000000000 and r1 >= 0x2000000000:
The lower/upper bounds haven't changed since they have high bits set in
u64 space and the jmp32 tests can only refine bounds in the low bits.
However, for the var part the expectation would have been 0x7f000007ff
or something less precise up to 0x7fffffffff. A outcome of 0x7f00000000
is not correct since it would contradict the earlier probed bounds
where we know that the result should have been in [0x200,0x400] in u32
space. Therefore, tests with such info will lead to wrong verifier
assumptions later on like falsely predicting conditional jumps to be
always taken, etc.
The issue here is that __reg_bound_offset32()'s implementation from
commit 581738a681b6 ("bpf: Provide better register bounds after jmp32
instructions") makes an incorrect range assumption:
In the above walk-through example, __reg_bound_offset32() as-is chose
a range after masking with 0xffffffff of [0x0,0x0] since umin:0x2000000000
and umax:0x4000000000 and therefore the lo32 part was clamped to 0x0 as
well. However, in the umin:0x2000000000 and umax:0x4000000000 range above
we'd end up with an actual possible interval of [0x0,0xffffffff] for u32
space instead.
In case of the original reproducer, the situation looked as follows at
insn 5 for r0:
After the fall-through, we similarly forced the var_off result into
the wrong range [0x30303030,0x3030302f] suggesting later on that fixed
bits must only be of 0x30303020 with 0x10000001f unknowns whereas such
assumption can only be made when both bounds in hi32 range match.
Originally, I was thinking to fix this by moving reg into a temp reg and
use proper coerce_reg_to_size() helper on the temp reg where we can then
based on that define the range tnum for later intersection:
In the case of the concrete example, this gives us a more conservative unknown
section. Thus, after knowing r1 <= 0x4000000000 and r1 >= 0x2000000000 and
w1 <= 0x400 and w1 >= 0x200:
However, above new __reg_bound_offset32() has no effect on refining the
knowledge of the register contents. Meaning, if the bounds in hi32 range
mismatch we'll get the identity function given the range reg spans
[0x0,0xffffffff] and we cast var_off into lo32 only to later on binary
or it again with the hi32.
Likewise, if the bounds in hi32 range match, then we mask both bounds
with 0xffffffff, use the resulting umin/umax for the range to later
intersect the lo32 with it. However, _prior_ called __reg_bound_offset()
did already such intersection on the full reg and we therefore would only
repeat the same operation on the lo32 part twice.
Given this has no effect and the original commit had false assumptions,
this patch reverts the code entirely which is also more straight forward
for stable trees: apparently 581738a681b6 got auto-selected by Sasha's
ML system and misclassified as a fix, so it got sucked into v5.4 where
it should never have landed. A revert is low-risk also from a user PoV
since it requires a recent kernel and llc to opt-into -mcpu=v3 BPF CPU
to generate jmp32 instructions. A proper bounds refinement would need a
significantly more complex approach which is currently being worked, but
no stable material [0]. Hence revert is best option for stable. After the
revert, the original reported program gets rejected as follows:
hyperv_timer.c exports hyperv_cs, which is used by stimers and the
timesync mechanism. However, the clocksource dependency is not
needed: these mechanisms only depend on the partition reference
counter (which can be read via a MSR or via the TSC Reference Page).
Introduce the (function) pointer hv_read_reference_counter, as an
embodiment of the partition reference counter read, and export it
in place of the hyperv_cs pointer. The latter can be removed.
This should clarify that there's no relationship between Hyper-V
stimers & timesync and the Linux clocksource abstractions. No
functional or semantic change.
Suggested-by: Michael Kelley <mikelley@microsoft.com> Signed-off-by: Andrea Parri <parri.andrea@gmail.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200109160650.16150-2-parri.andrea@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f32593773549 ("r8169: check that Realtek PHY driver module is loaded") Reported-by: Chih-Wei Huang <cwhuang@android-x86.org> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vti6_rcv function performs some tests on the retrieved tunnel
including checking the IP protocol, the XFRM input policy, the
source and destination address.
In all but one places the skb is released in the error case. When
the input policy check fails the network packet is leaked.
Using the same goto-label discard in this case to fix this problem.
Fixes: ed1efb2aefbb ("ipv6: Add support for IPsec virtual tunnel interfaces") Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com> Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB-ID signal has a pullup on the schematic, but in reality it's not
pulled up, so add a GPIO pullup. And we also need a usb0_vbus_power-supply
for VBUS detection.
This fixes OTG mode detection and charging issues on TBS A711 tablet.
The issues came from ID pin reading 0, causing host mode to be enabled,
when it should not be, leading to DRVVBUS being enabled, which disabled
the charger.
Fixes: f2f221c7810b824e ("ARM: dts: sun8i: a711: Enable USB OTG") Signed-off-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason we have stab->lock and bucket->locks in sockmap code is to
handle checking EEXIST in update/delete cases. We need to be careful during
an update operation that we check for EEXIST and we need to ensure that the
psock object is not in some partial state of removal/insertion while we do
this. So both map_update_common and sock_map_delete need to guard from being
run together potentially deleting an entry we are checking, etc. But by the
time we get to the tear-down code in sock_{ma[|hash}_free we have already
disconnected the map and we just did synchronize_rcu() in the line above so
no updates/deletes should be in flight. Because of this we can drop the
bucket locks from the map free'ing code, noting no update/deletes can be
in-flight.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Reported-by: Jakub Sitnicki <jakub@cloudflare.com> Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/158385850787.30597.8346421465837046618.stgit@john-Precision-5820-Tower Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
btf_enum_check_member() was currently sure to recognize the size of
"enum" type members in struct/union as the size of "int" even if
its size was packed.
This patch fixes BTF enum verification to use the correct size
of member in BPF programs.
Local storage array isn't initialized, so if cgroup storage allocation fails
for BPF_CGROUP_STORAGE_SHARED, error handling code will attempt to free
uninitialized pointer for BPF_CGROUP_STORAGE_PERCPU storage type. Avoid this
by always initializing storage pointers to NULLs.
The current x32 BPF JIT is incorrect for JMP32 JSET BPF_X when the upper
32 bits of operand registers are non-zero in certain situations.
The problem is in the following code:
case BPF_JMP | BPF_JSET | BPF_X:
case BPF_JMP32 | BPF_JSET | BPF_X:
...
/* and dreg_lo,sreg_lo */
EMIT2(0x23, add_2reg(0xC0, sreg_lo, dreg_lo));
/* and dreg_hi,sreg_hi */
EMIT2(0x23, add_2reg(0xC0, sreg_hi, dreg_hi));
/* or dreg_lo,dreg_hi */
EMIT2(0x09, add_2reg(0xC0, dreg_lo, dreg_hi));
This code checks the upper bits of the operand registers regardless if
the BPF instruction is BPF_JMP32 or BPF_JMP64. Registers dreg_hi and
dreg_lo are not loaded from the stack for BPF_JMP32, however, they can
still be polluted with values from previous instructions.
The following BPF program demonstrates the bug. The jset64 instruction
loads the temporary registers and performs the jump, since ((u64)r7 &
(u64)r8) is non-zero. The jset32 should _not_ be taken, as the lower
32 bits are all zero, however, the current JIT will take the branch due
the pollution of temporary registers from the earlier jset64.
The expected return value of this program is 2; under the buggy x32 JIT
it returns 0. The fix is to skip using the upper 32 bits for jset32 and
compare the upper 32 bits for jset64 only.
All tests in test_bpf.ko and selftests/bpf/test_verifier continue to
pass with this change.
We found this bug using our automated verification tool, Serval.
Fixes: 69f827eb6e14 ("x32: bpf: implement jitting of JMP32") Co-developed-by: Xi Wang <xi.wang@gmail.com> Signed-off-by: Xi Wang <xi.wang@gmail.com> Signed-off-by: Luke Nelson <luke.r.nels@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20200305234416.31597-1-luke.r.nels@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nvidia card may come with a "phantom" UCSI device, and its driver gets
stuck in probe routine, prevents any system PM operations like suspend.
There's an unaccounted case that the target time can equal to jiffies in
gpu_i2c_check_status(), let's solve that by using readl_poll_timeout()
instead of jiffies comparison functions.
Fixes: c71bcdcb42a7 ("i2c: add i2c bus driver for NVIDIA GPU") Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Ajay Gupta <ajayg@nvidia.com> Tested-by: Ajay Gupta <ajayg@nvidia.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set skb->tc_redirected to 1, otherwise the ifb driver drops the packet.
Set skb->tc_from_ingress to 1 to reinject the packet back to the ingress
path after leaving the ifb egress path.
This patch inconditionally sets on these two skb fields that are
meaningful to the ifb driver. The existing forward action is guaranteed
to run from ingress path.
Fixes: 39e6dea28adc ("netfilter: nf_tables: add forward expression to the netdev family") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a frame is transmitted via the nl80211 TX rather than as a
normal frame, IEEE80211_TX_CTRL_PORT_CTRL_PROTO wasn't set and
this will lead to wrong decisions (rate control etc.) being made
about the frame; fix this.
The he_sr_control field is just a u8, so le32_to_cpu()
shouldn't be applied to it; this was evidently copied
from ieee80211_he_oper_size(). Fix it, and also adjust
the type of the local variable.
When it's probing all of a fileserver's interfaces to find which one is
best to use, afs_do_probe_fileserver() takes a lock on the server record
and notes the pointer to the address list.
It doesn't, however, pin the address list, so as soon as it drops the
lock, there's nothing to stop the address list from being freed under
us.
Fix this by taking a ref on the address list inside the locked section
and dropping it at the end of the function.
Fix a couple of tracelines to indicate the usage count after the atomic op,
not the usage count before it to be consistent with other afs and rxrpc
trace lines.
Change the wording of the afs_call_trace_work trace ID label from "WORK" to
"QUEUE" to reflect the fact that it's queueing work, not doing work.
Fixes: 341f741f04be ("afs: Refcount the afs_call struct") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the handling of signals in client rxrpc calls made by the afs
filesystem. Ignore signals completely, leaving call abandonment or
connection loss to be detected by timeouts inside AF_RXRPC.
Allowing a filesystem call to be interrupted after the entire request has
been transmitted and an abort sent means that the server may or may not
have done the action - and we don't know. It may even be worse than that
for older servers.
Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not sufficient to do 'uctx->len != (sizeof(struct xfrm_user_sec_ctx) +
uctx->ctx_len)' check only, as uctx->len may be greater than nla_len(rt),
in which case it will cause slab-out-of-bounds when accessing uctx->ctx_str
later.
This patch is to fix it by return -EINVAL when uctx->len > nla_len(rt).
Fixes: df71837d5024 ("[LSM-IPSec]: Security association restriction.") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been discovered that this feature can globally block the RX port,
so it should be allowed for highly privileged users only.
Fixes: 03404e8ae652("IB/mlx5: Add support to dropless RQ") Link: https://lore.kernel.org/r/20200322124906.1173790-1-leon@kernel.org Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main difference between send and receive SW completions is related to
separate treatment of WQ queue. For receive completions, the initial index
to be flushed is stored in "tail", while for send completions, it is in
deleted "last_poll".
When we read the global counter and there's any dynamic counter allocated,
the value of a hwcounter is the sum of the default counter and all dynamic
counters. So the number of hwcounters of a dynamically allocated counter
must be same as of the default counter, otherwise there will be read
violations.
This fixes the KASAN slab-out-of-bounds bug:
BUG: KASAN: slab-out-of-bounds in rdma_counter_get_hwstat_value+0x36d/0x390 [ib_core]
Read of size 8 at addr ffff8884192a5778 by task rdma/10138
The handling of notify->work did not properly maintain notify->kref in two
cases:
1) where the work was already scheduled, another irq_set_affinity_locked()
would get the ref and (no-op-ly) schedule the work. Thus when
irq_affinity_notify() ran, it would drop the original ref but not the
additional one.
2) when cancelling the (old) work in irq_set_affinity_notifier(), if there
was outstanding work a ref had been got for it but was never put.
Fix both by checking the return values of the work handling functions
(schedule_work() for (1) and cancel_work_sync() for (2)) and put the
extra ref if the return value indicates preexisting work.
Fixes: cd7eab44e994 ("genirq: Add IRQ affinity notifiers") Fixes: 59c39840f5ab ("genirq: Prevent use-after-free and work list corruption") Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Ben Hutchings <ben@decadent.org.uk> Link: https://lkml.kernel.org/r/24f5983f-2ab5-e83a-44ee-a45b5f9300f5@solarflare.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an AFS service handler function aborts a call, AF_RXRPC marks the call
as complete - which means that it's not going to get any more packets from
the receiver. This is a problem because reception of the final ACK is what
triggers afs_deliver_to_call() to drop the final ref on the afs_call
object.
Instead, aborted AFS service calls may then just sit around waiting for
ever or until they're displaced by a new call on the same connection
channel or a connection-level abort.
Fix this by calling afs_set_call_complete() to finalise the afs_call struct
representing the call.
However, we then need to drop the ref that stops the call from being
deallocated. We can do this in afs_set_call_complete(), as the work queue
is holding a separate ref of its own, but then we shouldn't do it in
afs_process_async_call() and afs_delete_async_call().
call->drop_ref is set to indicate that a ref needs dropping for a call and
this is dealt with when we transition a call to AFS_CALL_COMPLETE.
But then we also need to get rid of the ref that pins an asynchronous
client call. We can do this by the same mechanism, setting call->drop_ref
for an async client call too.
We can also get rid of call->incoming since nothing ever sets it and only
one thing ever checks it (futilely).
A trace of the rxrpc_call and afs_call struct ref counting looks like:
The abort generated in SRXAFSCB_ProbeUuid(), labelled "K-1", indicates that
the local filesystem/cache manager didn't recognise the UUID as its own.
Fixes: 2067b2b3f484 ("afs: Fix the CB.ProbeUuid service handler to reply correctly") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following modify sequence (loosely based on ipoib) will lose a pkey
modifcation:
- Modify (pkey index, port)
- Modify (new pkey index, NO port)
After the first modify, the qp_pps list will have saved the pkey and the
unit on the main list.
During the second modify, get_new_pps() will fetch the port from qp_pps
and read the new pkey index from qp_attr->pkey_index. The state will
still be zero, or IB_PORT_PKEY_NOT_VALID. Because of the invalid state,
the new values will never replace the one in the qp pps list, losing the
new pkey.
This happens because the following if statements will never correct the
state because the first term will be false. If the code had been executed,
it would incorrectly overwrite valid values.
There is no compensating cgroup_bpf_put() for each ancestor cgroup in
cgroup_bpf_inherit(). If compute_effective_progs returns error, those cgroups
won't be freed ever. Fix it by putting them in cleanup code path.
Commit aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option +
quirk mechanism") was added to deal with spurious wakeups on one specific
model of the HP x2 10 series. In the mean time I have learned that there
are at least 3 different HP x2 10 models:
Bay Trail SoC + AXP288 PMIC
Cherry Trail SoC + AXP288 PMIC
Cherry Trail SoC + TI PMIC
And the original quirk is only correct for (and only matches the)
Cherry Trail SoC + TI PMIC model.
The Bay Trail SoC + AXP288 PMIC model has different DMI strings, has
the external EC interrupt on a different GPIO pin and only needs to ignore
wakeups on the EC interrupt, the INT0002 device works fine on this model.
This commit adds an extra DMI based quirk for the HP x2 10 BYT + AXP288
model, ignoring wakeups for ACPI GPIO events on the EC interrupt pin
on this model. This fixes spurious wakeups from suspend on this model.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200302111225.6641-3-hdegoede@redhat.com Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option +
quirk mechanism") was added to deal with spurious wakeups on one specific
model of the HP x2 10 series.
The approach taken there was to add a bool controlling wakeup support for
all ACPI GPIO events. This was sufficient for the specific HP x2 10 model
the commit was trying to fix, but in the mean time other models have
turned up which need a similar workaround to avoid spurious wakeups from
suspend, but only for one of the pins on which the ACPI tables request
ACPI GPIO events.
Since the honor_wakeup option was added to be able to ignore wake events,
the name was perhaps not the best, this commit renames it to ignore_wake
and changes it to a string with the following format:
gpiolib_acpi.ignore_wake=controller@pin[,controller@pin[,...]]
This allows working around spurious wakeup issues on a per pin basis.
This commit also reworks the existing quirk for the HP x2 10 so that
it functions as before.
Note:
-This removes the honor_wakeup parameter. This has only been upstream for
a short time and to the best of my knowledge there are no users using
this module parameter.
-The controller@pin[,controller@pin[,...]] syntax is based on an existing
kernel module parameter using the same controller@pin format. That version
uses ';' as separator, but in practice that is problematic because grub2
cannot handle this without taking special care to escape the ';', so here
we are using a ',' as separator instead which does not have this issue.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200302111225.6641-2-hdegoede@redhat.com Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option +
quirk mechanism") added a quirk for some models of the HP x2 10 series.
There are 2 issues with the comment describing the quirk:
1) The comment claims the DMI quirk applies to all Cherry Trail based HP x2
10 models. In the mean time I have learned that there are at least 3
models of the HP x2 10 models:
Bay Trail SoC + AXP288 PMIC
Cherry Trail SoC + AXP288 PMIC
Cherry Trail SoC + TI PMIC
And this quirk's DMI matches only match the Cherry Trail SoC + TI PMIC
SoC, which is good because we want a slightly different quirk for the
others. This commit updates the comment to make it clear that the quirk
is only for the Cherry Trail SoC + TI PMIC models.
2) The comment says that it is ok to disable wakeup on all ACPI GPIO event
handlers, because there is only the one for the embedded-controller
events. This is not true, there also is a handler for the special
INT0002 device which is related to USB wakeups. We need to also disable
wakeups on that one because the device turns of the USB-keyboard built
into the dock when closing the lid. The XHCI controller takes a while
to notice this, so it only notices it when already suspended, causing
a spurious wakeup because of this. So disabling wakeup on all handlers
is the right thing to do, but not because there only is the one handler
for the EC events. This commit updates the comment to correctly reflect
this.
Fixes: aa23ca3d98f7 ("gpiolib: acpi: Add honor_wakeup module-option + quirk mechanism") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20200302111225.6641-1-hdegoede@redhat.com Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on CONFIG_VMAP_STACK and the THREAD_SIZE / PAGE_SIZE ratio the
space for task stacks can be allocated using __vmalloc_node_range(),
alloc_pages_node() and kmem_cache_alloc_node().
In the first and the second cases page->mem_cgroup pointer is set, but
in the third it's not: memcg membership of a slab page should be
determined using the memcg_from_slab_page() function, which looks at
page->slab_cache->memcg_params.memcg . In this case, using
mod_memcg_page_state() (as in account_kernel_stack()) is incorrect:
page->mem_cgroup pointer is NULL even for pages charged to a non-root
memory cgroup.
It can lead to kernel_stack per-memcg counters permanently showing 0 on
some architectures (depending on the configuration).
In order to fix it, let's introduce a mod_memcg_obj_state() helper,
which takes a pointer to a kernel object as a first argument, uses
mem_cgroup_from_obj() to get a RCU-protected memcg pointer and calls
mod_memcg_state(). It allows to handle all possible configurations
(CONFIG_VMAP_STACK and various THREAD_SIZE/PAGE_SIZE values) without
spilling any memcg/kmem specifics into fork.c .
Note: This is a special version of the patch created for stable
backports. It contains code from the following two patches:
- mm: memcg/slab: introduce mem_cgroup_from_obj()
- mm: fork: fix kernel_stack memcg stats for various stack implementations
[guro@fb.com: introduce mem_cgroup_from_obj()] Link: http://lkml.kernel.org/r/20200324004221.GA36662@carbon.dhcp.thefacebook.com Fixes: 4d96ba353075 ("mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages") Signed-off-by: Roman Gushchin <guro@fb.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Bharata B Rao <bharata@linux.ibm.com> Cc: Shakeel Butt <shakeelb@google.com> Cc: <stable@vger.kernel.org> Link: http://lkml.kernel.org/r/20200303233550.251375-1-guro@fb.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000000c3447c
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
CPU: 11 PID: 7519 Comm: lt-ndctl Not tainted 5.6.0-rc7-autotest #1
...
NIP [c000000000c3447c] vmemmap_populated+0x98/0xc0
LR [c000000000088354] vmemmap_free+0x144/0x320
Call Trace:
section_deactivate+0x220/0x240
__remove_pages+0x118/0x170
arch_remove_memory+0x3c/0x150
memunmap_pages+0x1cc/0x2f0
devm_action_release+0x30/0x50
release_nodes+0x2f8/0x3e0
device_release_driver_internal+0x168/0x270
unbind_store+0x130/0x170
drv_attr_store+0x44/0x60
sysfs_kf_write+0x68/0x80
kernfs_fop_write+0x100/0x290
__vfs_write+0x3c/0x70
vfs_write+0xcc/0x240
ksys_write+0x7c/0x140
system_call+0x5c/0x68
The crash is due to NULL dereference at
test_bit(idx, ms->usage->subsection_map);
due to ms->usage = NULL in pfn_section_valid()
With commit d41e2f3bd546 ("mm/hotplug: fix hot remove failure in
SPARSEMEM|!VMEMMAP case") section_mem_map is set to NULL after
depopulate_section_mem(). This was done so that pfn_page() can work
correctly with kernel config that disables SPARSEMEM_VMEMMAP. With that
config pfn_to_page does
Now with SPASEMEM_VMEMAP enabled, mem_section->usage->subsection_map is
used to check the pfn validity (pfn_valid()). Since section_deactivate
release mem_section->usage if a section is fully deactivated,
pfn_valid() check after a subsection_deactivate cause a kernel crash.
static inline int pfn_valid(unsigned long pfn)
{
...
return early_section(ms) || pfn_section_valid(ms, pfn);
}
where
static inline int pfn_section_valid(struct mem_section *ms, unsigned long pfn)
{
int idx = subsection_map_index(pfn);
Avoid this by clearing SECTION_HAS_MEM_MAP when mem_section->usage is
freed. For architectures like ppc64 where large pages are used for
vmmemap mapping (16MB), a specific vmemmap mapping can cover multiple
sections. Hence before a vmemmap mapping page can be freed, the kernel
needs to make sure there are no valid sections within that mapping.
Clearing the section valid bit before depopulate_section_memap enables
this.
[aneesh.kumar@linux.ibm.com: add comment] Link: http://lkml.kernel.org/r/20200326133235.343616-1-aneesh.kumar@linux.ibm.comLink: Fixes: d41e2f3bd546 ("mm/hotplug: fix hot remove failure in SPARSEMEM|!VMEMMAP case") Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com> Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com> Reviewed-by: Baoquan He <bhe@redhat.com> Reviewed-by: Wei Yang <richard.weiyang@gmail.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Dan Williams <dan.j.williams@intel.com> Cc: David Hildenbrand <david@redhat.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We see multiple issues with the implementation/interface to compute
whether a memory block can be offlined (exposed via
/sys/devices/system/memory/memoryX/removable) and would like to simplify
it (remove the implementation).
1. It runs basically lockless. While this might be good for performance,
we see possible races with memory offlining that will require at
least some sort of locking to fix.
2. Nowadays, more false positives are possible. No arch-specific checks
are performed that validate if memory offlining will not be denied
right away (and such check will require locking). For example, arm64
won't allow to offline any memory block that was added during boot -
which will imply a very high error rate. Other archs have other
constraints.
3. The interface is inherently racy. E.g., if a memory block is detected
to be removable (and was not a false positive at that time), there is
still no guarantee that offlining will actually succeed. So any
caller already has to deal with false positives.
4. It is unclear which performance benefit this interface actually
provides. The introducing commit 5c755e9fd813 ("memory-hotplug: add
sysfs removable attribute for hotplug memory remove") mentioned
"A user-level agent must be able to identify which sections
of memory are likely to be removable before attempting the
potentially expensive operation."
However, no actual performance comparison was included.
Known users:
- lsmem: Will group memory blocks based on the "removable" property. [1]
- chmem: Indirect user. It has a RANGE mode where one can specify
removable ranges identified via lsmem to be offlined. However,
it also has a "SIZE" mode, which allows a sysadmin to skip the
manual "identify removable blocks" step. [2]
- powerpc-utils: Uses the "removable" attribute to skip some memory
blocks right away when trying to find some to offline+remove.
However, with ballooning enabled, it already skips this
information completely (because it once resulted in many false
negatives). Therefore, the implementation can deal with false
positives properly already. [3]
According to Nathan Fontenot, DLPAR on powerpc is nowadays no longer
driven from userspace via the drmgr command (powerpc-utils). Nowadays
it's managed in the kernel - including onlining/offlining of memory
blocks - triggered by drmgr writing to /sys/kernel/dlpar. So the
affected legacy userspace handling is only active on old kernels. Only
very old versions of drmgr on a new kernel (unlikely) might execute
slower - totally acceptable.
With CONFIG_MEMORY_HOTREMOVE, always indicating "removable" should not
break any user space tool. We implement a very bad heuristic now.
Without CONFIG_MEMORY_HOTREMOVE we cannot offline anything, so report
"not removable" as before.
Original discussion can be found in [4] ("[PATCH RFC v1] mm:
is_mem_section_removable() overhaul").
Other users of is_mem_section_removable() will be removed next, so that
we can remove is_mem_section_removable() completely.
claim_swapfile() currently keeps the inode locked when it is successful,
or the file is already swapfile (with -EBUSY). And, on the other error
cases, it does not lock the inode.
This inconsistency of the lock state and return value is quite confusing
and actually causing a bad unlock balance as below in the "bad_swap"
section of __do_sys_swapon().
This commit fixes this issue by moving the inode_lock() and IS_SWAPFILE
check out of claim_swapfile(). The inode is unlocked in
"bad_swap_unlock_inode" section, so that the inode is ensured to be
unlocked at "bad_swap". Thus, error handling codes after the locking now
jumps to "bad_swap_unlock_inode" instead of "bad_swap".
=====================================
WARNING: bad unlock balance detected!
5.5.0-rc7+ #176 Not tainted
-------------------------------------
swapon/4294 is trying to release lock (&sb->s_type->i_mutex_key) at: __do_sys_swapon+0x94b/0x3550
but there are no more locks to release!
other info that might help us debug this:
no locks held by swapon/4294.
If a station is still marked as authorized, mark it as no longer
so before removing its keys. This allows frames transmitted to it
to be rejected, providing additional protection against leaking
plain text data during the disconnection flow.
If we know that we have an encrypted link (based on having had
a key configured for TX in the past) then drop all data frames
in the key selection handler if there's no key anymore.
This fixes an issue with mac80211 internal TXQs - there we can
buffer frames for an encrypted link, but then if the key is no
longer there when they're dequeued, the frames are sent without
encryption. This happens if a station is disconnected while the
frames are still on the TXQ.
Detecting that a link should be encrypted based on a first key
having been configured for TX is fine as there are no use cases
for a connection going from with encryption to no encryption.
With extended key IDs, however, there is a case of having a key
configured for only decryption, so we can't just trigger this
behaviour on a key being configured.
The new opmode notification used this attribute with a u8, when
it's documented as a u32 and indeed used in userspace as such,
it just happens to work on little-endian systems since userspace
isn't doing any strict size validation, and the u8 goes into the
lower byte. Fix this.
Some USB bridge devices will return a default set of characteristics during
initialization. And then, once an attached drive has spun up, substitute
the actual parameters reported by the drive. According to the SCSI spec,
the device should return a UNIT ATTENTION in case any reported parameters
change. But in this case the change is made silently after a small window
where default values are reported.
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of
physical block size") validated the reported optimal I/O size against the
physical block size to overcome problems with devices reporting nonsensical
transfer sizes. However, this validation did not account for the fact that
aforementioned devices will return default values during a brief window
during spin-up. The subsequent change in reported characteristics would
invalidate the checking that had previously been performed.
Unset a previously configured optimal I/O size should the sanity checking
fail on subsequent revalidate attempts.
Link: https://lore.kernel.org/r/33fb522e-4f61-1b76-914f-c9e6a3553c9b@gmail.com Cc: Bryan Gurney <bgurney@redhat.com> Cc: <stable@vger.kernel.org> Reported-by: Bernhard Sulzer <micraft.b@gmail.com> Tested-by: Bernhard Sulzer <micraft.b@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc 10 will default to -fno-common, which causes this error at link
time:
(.text+0x0): multiple definition of `yylloc'; dtc-lexer.lex.o (symbol from plugin):(.text+0x0): first defined here
This is because both dtc-lexer as well as dtc-parser define the same
global symbol yyloc. Before with -fcommon those were merged into one
defintion. The proper solution would be to to mark this as "extern",
however that leads to:
dtc-lexer.l:26:16: error: redundant redeclaration of 'yylloc' [-Werror=redundant-decls]
26 | extern YYLTYPE yylloc;
| ^~~~~~
In file included from dtc-lexer.l:24:
dtc-parser.tab.h:127:16: note: previous declaration of 'yylloc' was here
127 | extern YYLTYPE yylloc;
| ^~~~~~
cc1: all warnings being treated as errors
which means the declaration is completely redundant and can just be
dropped.
Signed-off-by: Dirk Mueller <dmueller@suse.com> Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[robh: cherry-pick from upstream] Cc: stable@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The O= directory existence check failed because the check script ran in
the build target directory instead of the directory where I ran the make
command.
To fix that, once change directory to $(PWD) and check O= directory,
since the PWD is set to where the make command runs.
Fixes: c883122acc0d ("perf tools: Let O= makes handle relative paths") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Michal Marek <michal.lkml@markovi.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sasha Levin <sashal@kernel.org> Cc: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: stable@vger.kernel.org Link: http://lore.kernel.org/lkml/158351957799.3363.15269768530697526765.stgit@devnote2 Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some unexplained reason, commit d1d1a96bdb44 ("rtlwifi: rtl8188ee:
Remove local configuration variable") broke at least one system. As
the only net effect of the change was to remove 2 bytes from the start
of struct phy_status_rpt, this patch adds 2 bytes of padding at the
beginning of the struct.
Fixes: d1d1a96bdb44 ("rtlwifi: rtl8188ee: Remove local configuration variable") Cc: Stable <stable@vger.kernel.org> # V5.4+ Reported-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in> Tested-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not depend on dwfl_module_addrsym() because it can fail on user-space
shared libraries.
Actually, same bug was fixed by commit 664fee3dc379 ("perf probe: Do not
use dwfl_module_addrsym if dwarf_diename finds symbol name"), but commit 07d369857808 ("perf probe: Fix wrong address verification) reverted to
get actual symbol address from symtab.
This fixes it again by getting symbol address from DIE, and only if the
DIE has only address range, it uses dwfl_module_addrsym().
When we put an event with multiple probes, perf-probe fails to delete
with filters. This comes from a failure to list up the event name
because of overwrapping its name.
To fix this issue, skip to list up the event which has same name.
Without this patch:
# perf probe -l \*
probe_perf:map__map_ip (on perf_sample__fprintf_brstackoff:21@
probe_perf:map__map_ip (on perf_sample__fprintf_brstackoff:25@
probe_perf:map__map_ip (on append_inlines:12@util/machine.c in
probe_perf:map__map_ip (on unwind_entry:19@util/machine.c in /
probe_perf:map__map_ip (on map__map_ip@util/map.h in /home/mhi
probe_perf:map__map_ip (on map__map_ip@util/map.h in /home/mhi
# perf probe -d \*
"*" does not hit any event.
Error: Failed to delete events. Reason: No such file or directory (Code: -2)
In order to use efi_mem_type(), one needs CONFIG_EFI enabled. Otherwise
that function is undefined. Use IS_ENABLED() to check and avoid the
ifdeffery as the compiler optimizes away the following unreachable code
then.
Fixes: 985e537a4082 ("x86/ioremap: Map EFI runtime services data as encrypted for SEV") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Borislav Petkov <bp@suse.de> Tested-by: Randy Dunlap <rdunlap@infradead.org> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/7561e981-0d9b-d62c-0ef2-ce6007aff1ab@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The L3 interconnect's memory map is from 0x0 to
0xffffffff. Out of this, System memory (SDRAM) can be
accessed from 0x80000000 to 0xffffffff (2GB)
DRA7 does support 4GB of SDRAM but upper 2GB can only be
accessed by the MPU subsystem.
Add the dma-ranges property to reflect the physical address limit
of the L3 bus.
Issues ere observed only with SATA on DRA7-EVM with 4GB RAM
and CONFIG_ARM_LPAE enabled. This is because the controller
supports 64-bit DMA and its driver sets the dma_mask to 64-bit
thus resulting in DMA accesses beyond L3 limit of 2G.
Setting the correct bus_dma_limit fixes the issue.
Signed-off-by: Roger Quadros <rogerq@ti.com> Cc: stable@kernel.org Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CEPH_OSDMAP_FULL/NEARFULL aren't set since mimic, so we need to consult
per-pool flags as well. Unfortunately the backwards compatibility here
is lacking:
- the change that deprecated OSDMAP_FULL/NEARFULL went into mimic, but
was guarded by require_osd_release >= RELEASE_LUMINOUS
- it was subsequently backported to luminous in v12.2.2, but that makes
no difference to clients that only check OSDMAP_FULL/NEARFULL because
require_osd_release is not client-facing -- it is for OSDs
Since all kernels are affected, the best we can do here is just start
checking both map flags and pool flags and send that to stable.
These checks are best effort, so take osdc->lock and look up pool flags
just once. Remove the FIXME, since filesystem quotas are checked above
and RADOS quotas are reflected in POOL_FLAG_FULL: when the pool reaches
its quota, both POOL_FLAG_FULL and POOL_FLAG_FULL_QUOTA are set.
Cc: stable@vger.kernel.org Reported-by: Yanhu Cao <gmayyyha@gmail.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Acked-by: Sage Weil <sage@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log