Remove non-privileged user access to power data contained in
/sys/class/powercap/intel-rapl*/*/energy_uj
Non-privileged users currently have read access to power data and can
use this data to form a security attack. Some privileged
drivers/applications need read access to this data, but don't expose it
to non-privileged users.
For example, thermald uses this data to ensure that power management
works correctly. Thus removing non-privileged access is preferred over
completely disabling this power reporting capability with
CONFIG_INTEL_RAPL=n.
Fixes: 95677a9a3847 ("PowerCap: Fix mode for energy counter") Signed-off-by: Len Brown <len.brown@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Espressobin boards have 3 ethernet ports and some of them got assigned more
then one MAC address. MAC addresses are stored in U-Boot environment.
Since commit a2c7023f7075c ("net: dsa: read mac address from DT for slave
device") kernel can use MAC addresses from DT for particular DSA port.
Currently Espressobin DTS file contains alias just for ethernet0.
This patch defines additional ethernet aliases in Espressobin DTS files, so
bootloader can fill correct MAC address for DSA switch ports if more MAC
addresses were specified.
DT alias ethernet1 is used for wan port, DT aliases ethernet2 and ethernet3
are used for lan ports for both Espressobin revisions (V5 and V7).
Fixes: 5253cb8c00a6f ("arm64: dts: marvell: espressobin: add ethernet alias") Cc: <stable@vger.kernel.org> # a2c7023f7075c: dsa: read mac address Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andre Heider <a.heider@gmail.com> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
[pali: Backported Espressobin rev V5 changes to 5.4 and 4.19 versions] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Strohman [Thu, 5 Nov 2020 20:28:50 +0000 (20:28 +0000)]
xfs: flush for older, xfs specific ioctls
837a6e7f5cdb ("fs: add generic UNRESVSP and ZERO_RANGE ioctl handlers") changed
ioctls XFS_IOC_UNRESVSP XFS_IOC_UNRESVSP64 and XFS_IOC_ZERO_RANGE to be generic
instead of xfs specific.
Because of this change, 36f11775da75 ("xfs: properly serialise fallocate against
AIO+DIO") needed adaptation, as 5.4 still uses the xfs specific ioctls.
Without this, xfstests xfs/242 and xfs/290 fail. Both of these tests test
XFS_IOC_ZERO_RANGE.
Fixes: 36f11775da75 ("xfs: properly serialise fallocate against AIO+DIO") Tested-by: Andy Strohman <astroh@amazon.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the device is resumed from runtime-suspend in
__device_release_driver() anyway, it is better to do that before
looking for busy managed device links from it to consumers, because
if there are any, device_links_unbind_consumers() will be called
and it will cause the consumer devices' drivers to unbind, so the
consumer devices will be runtime-resumed. In turn, resuming each
consumer device will cause the supplier to be resumed and when the
runtime PM references from the given consumer to it are dropped, it
may be suspended. Then, the runtime-resume of the next consumer
will cause the supplier to resume again and so on.
Update the code accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Fixes: 9ed9895370ae ("driver core: Functional dependencies tracking support") Cc: All applicable <stable@vger.kernel.org> # All applicable Tested-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit d12544fb2aa9 ("PM: runtime: Remove link state checks in
rpm_get/put_supplier()") nothing prevents the consumer device's
runtime PM from acquiring additional references to the supplier
device after pm_runtime_clean_up_links() has run (or even while it
is running), so calling this function from __device_release_driver()
may be pointless (or even harmful).
Moreover, it ignores stateless device links, so the runtime PM
handling of managed and stateless device links is inconsistent
because of it, so better get rid of it entirely.
Fixes: d12544fb2aa9 ("PM: runtime: Remove link state checks in rpm_get/put_supplier()") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: 5.1+ <stable@vger.kernel.org> # 5.1+ Tested-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While removing a device link, drop the supplier device's runtime PM
usage counter as many times as needed to drop all of the runtime PM
references to it from the consumer in addition to dropping the
consumer's link count.
Fixes: baa8809f6097 ("PM / runtime: Optimize the use of device links") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: 5.1+ <stable@vger.kernel.org> # 5.1+ Tested-by: Xiang Chen <chenxiang66@hisilicon.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently stack unwinder is a while(1) loop which relies on the dwarf
unwinder to signal termination, which in turn relies on dwarf info to do
so. This in theory could cause an infinite loop if the dwarf info was
somehow messed up or the register contents were etc.
This fix thus detects the excessive looping and breaks the loop.
panfrost_ioctl_madvise() and panfrost_gem_purge() acquire the mappings
and shmem locks in different orders, thus leading to a potential
the mappings lock first.
Fixes: bdefca2d8dc0 ("drm/panfrost: Add the panfrost_gem_mapping concept") Cc: <stable@vger.kernel.org> Cc: Christian Hewitt <christianshewitt@gmail.com> Reported-by: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Reviewed-by: Steven Price <steven.price@arm.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201101174016.839110-1-boris.brezillon@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In Bugzilla #208257, Julien Humbert reports that a 32-GB Kingston
flash drive spontaneously disconnects and reconnects, over and over.
Testing revealed that disabling Link Power Management for the drive
fixed the problem.
This patch adds a quirk entry for that drive to turn off LPM permanently.
CC: Hans de Goede <jwrdegoede@fedoraproject.org> CC: <stable@vger.kernel.org> Reported-and-tested-by: Julien Humbert <julroy67@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20201102145821.GA1478741@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we want to send a control status on our own time (through
delayed_status), make sure to handle a case where we may queue the
delayed status before the host requesting for it (when XferNotReady
is generated). Otherwise, the driver won't send anything because it's
not EP0_STATUS_PHASE yet. To resolve this, regardless whether
dwc->ep0state is EP0_STATUS_PHASE, make sure to clear the
dwc->delayed_status flag if dwc3_ep0_send_delayed_status() is called.
The control status can be sent when the host requests it later.
Prior to the commit that this one fixes, the FIFO size was derived from
the read-only register LPUARTx_FIFO[TXFIFOSIZE] using the following
formula:
TX FIFO size = 2 ^ (LPUARTx_FIFO[TXFIFOSIZE] - 1)
The documentation for LS1021A is a mess. Under chapter 26.1.3 LS1021A
LPUART module special consideration, it mentions TXFIFO_SZ and RXFIFO_SZ
being equal to 4, and in the register description for LPUARTx_FIFO, it
shows the out-of-reset value of TXFIFOSIZE and RXFIFOSIZE fields as "011",
even though these registers read as "101" in reality.
And when LPUART on LS1021A was working, the "101" value did correspond
to "16 datawords", by applying the formula above, even though the
documentation is wrong again (!!!!) and says that "101" means 64 datawords
(hint: it doesn't).
So the "new" formula created by commit f77ebb241ce0 has all the premises
of being wrong for LS1021A, because it relied only on false data and no
actual experimentation.
Interestingly, in commit c2f448cff22a ("tty: serial: fsl_lpuart: add
LS1028A support"), Michael Walle applied a workaround to this by manually
setting the FIFO widths for LS1028A. It looks like the same values are
used by LS1021A as well, in fact.
When the driver thinks that it has a deeper FIFO than it really has,
getty (user space) output gets truncated.
Many thanks to Michael for pointing out where to look.
Fixes: f77ebb241ce0 ("tty: serial: fsl_lpuart: correct the FIFO depth size") Suggested-by: Michael Walle <michael@walle.cc> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20201023013429.3551026-1-vladimir.oltean@nxp.com
Reviewed-by：Fugang Duan <fugang.duan@nxp.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write-URB busy flag was being cleared before the completion handler
was done with the URB, something which could lead to corrupt transfers
due to a racing write request if the URB is resubmitted.
Fixes: 507ca9bc0476 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.") Cc: stable <stable@vger.kernel.org> # 2.6.13 Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing platform_driver_unregister() before return
from serial_txx9_init in the error handling case when failed
to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI
defined.
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
When both the paes and the pkey kernel module are statically build
into the kernel, the paes cipher selftests run before the pkey
kernel module is initialized. So a static variable set in the pkey
init function and used in the pkey_clr2protkey function is not
initialized when the paes cipher's selftests request to call pckmo for
transforming a clear key value into a protected key.
This patch moves the initial setup of the static variable into
the function pck_clr2protkey. So it's possible, to use the function
for transforming a clear to a protected key even before the pkey
init function has been called and the paes selftests may run
successful.
Reported-by: Alexander Egorenkov <Alexander.Egorenkov@ibm.com> Cc: <stable@vger.kernel.org> # 4.20 Fixes: f822ad2c2c03 ("s390/pkey: move pckmo subfunction available checks away from module init") Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Fri, Nov 06, 2020 at 10:30:08PM +0800, Minh Yuan wrote:
> We recently discovered a slab-out-of-bounds read in fbcon in the latest
> kernel ( v5.10-rc2 for now ). The root cause of this vulnerability is that
> "fbcon_do_set_font" did not handle "vc->vc_font.data" and
> "vc->vc_font.height" correctly, and the patch
> <https://lkml.org/lkml/2020/9/27/223> for VT_RESIZEX can't handle this
> issue.
>
> Specifically, we use KD_FONT_OP_SET to set a small font.data for tty6, and
> use KD_FONT_OP_SET again to set a large font.height for tty1. After that,
> we use KD_FONT_OP_COPY to assign tty6's vc_font.data to tty1's vc_font.data
> in "fbcon_do_set_font", while tty1 retains the original larger
> height. Obviously, this will cause an out-of-bounds read, because we can
> access a smaller vc_font.data with a larger vc_font.height.
Further there was only one user ever.
- Android's loadfont, busybox and console-tools only ever use OP_GET
and OP_SET
- fbset documentation only mentions the kernel cmdline font: option,
not anything else.
- systemd used OP_COPY before release 232 published in Nov 2016
Now unfortunately the crucial report seems to have gone down with
gmane, and the commit message doesn't say much. But the pull request
hints at OP_COPY being broken
https://github.com/systemd/systemd/pull/3651
So in other words, this never worked, and the only project which
foolishly every tried to use it, realized that rather quickly too.
Instead of trying to fix security issues here on dead code by adding
missing checks, fix the entire thing by removing the functionality.
Note that systemd code using the OP_COPY function ignored the return
value, so it doesn't matter what we're doing here really - just in
case a lone server somewhere happens to be extremely unlucky and
running an affected old version of systemd. The relevant code from
font_copy_to_all_vcs() in systemd was:
/* copy font from active VT, where the font was uploaded to */
cfo.op = KD_FONT_OP_COPY;
cfo.height = vcs.v_active-1; /* tty1 == index 0 */
(void) ioctl(vcfd, KDFONTOP, &cfo);
Note this just disables the ioctl, garbage collecting the now unused
callbacks is left for -next.
v2: Tetsuo found the old mail, which allowed me to find it on another
archive. Add the link too.
drivers/hwtracing/coresight/coresight-etm-perf.c: In function 'etm_setup_aux':
drivers/hwtracing/coresight/coresight-etm-perf.c:226:37: warning:
passing argument 1 of 'coresight_get_enabled_sink' makes pointer from integer without a cast
Actually, the warning is fatal, since the call is
sink = coresight_get_enabled_sink(true);
However, the argument to coresight_get_enabled_sink() is now a pointer.
The parameter change was introduced with commit 8fd52a21ab57
("coresight: Make sysfs functional on topologies with per core sink").
In the upstream kernel, the call is removed with commit bb1860efc817
("coresight: etm: perf: Sink selection using sysfs is deprecated").
That commit alone would, however, likely not solve the problem.
It looks like at least two more commits would be needed.
716f5652a131 coresight: etm: perf: Fix warning caused by etm_setup_aux failure 8e264c52e1da coresight: core: Allow the coresight core driver to be built as a module 39a7661dcf65 coresight: Fix uninitialised pointer bug in etm_setup_aux()
Looking into the coresight code, I see several additional commits affecting
the sysfs interface since v5.4. I have no idea what would actually be needed
for stable code in v5.4.y, short of applying them all.
With all this in mind, I would suggest to revert commit 8fd52a21ab57
("coresight: Make sysfs functional on topologies with per core sink")
from v5.4.y, especially since it is not marked as bug fix or for stable.
The call to rcu_cpu_starting() in secondary_start_kernel() is not early
enough in the CPU-hotplug onlining process, which results in lockdep
splats as follows:
The user level OpenCL code shouldn't have to align start and end
addresses to a page boundary. That is better handled in the nouveau
driver. The npages field is also redundant since it can be computed
from the start and end addresses.
Signed-off-by: Ralph Campbell <rcampbell@nvidia.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code:
trb->length = cpu_to_le32(TRB_BURST_LEN(priv_ep->trb_burst_size)
| TRB_LEN(length));
TRB_BURST_LEN(priv_ep->trb_burst_size) may be overflow for int 32 if
priv_ep->trb_burst_size is equal or larger than 0x80;
Below is the Coverity warning:
sign_extension: Suspicious implicit sign extension: priv_ep->trb_burst_size
with type u8 (8 bits, unsigned) is promoted in priv_ep->trb_burst_size << 24
to type int (32 bits, signed), then sign-extended to type unsigned long
(64 bits, unsigned). If priv_ep->trb_burst_size << 24 is greater than 0x7FFFFFFF,
the upper bits of the result will all be 1.
To fix it, it needs to add an explicit cast to unsigned int type for ((p) << 24).
Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move the nvmet_req_init() tracepoint after we parse the command in
nvmet_req_init() so that we can get rid of the duplicate
nvmet_find_namespace() call.
Rename __assign_disk_name() -> __assign_req_name(). Now that we call
tracepoint after parsing the command simplify the newly added
__assign_req_name() which fixes this bug.
During __vsock_create() CAP_NET_ADMIN is used to determine if the
vsock_sock->trusted should be set to true. This value is used later
for determing if a remote connection should be allowed to connect
to a restricted VM. Unfortunately, if the caller doesn't have
CAP_NET_ADMIN, an audit message such as an selinux denial is
generated even if the caller does not want a trusted socket.
Logging errors on success is confusing. To avoid this, switch the
capable(CAP_NET_ADMIN) check to the noaudit version.
Reported-by: Roman Kiryanov <rkir@google.com>
https://android-review.googlesource.com/c/device/generic/goldfish/+/1468545/ Signed-off-by: Jeff Vander Stoep <jeffv@google.com> Reviewed-by: James Morris <jamorris@linux.microsoft.com> Link: https://lore.kernel.org/r/20201023143757.377574-1-jeffv@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After a loss of transport due to an adapter migration or crash/disconnect
from the host partner there is a tiny window where we can race adjusting
the request_limit of the adapter. The request limit is atomically
increased/decreased to track the number of inflight requests against the
allowed limit of our VIOS partner.
After a transport loss we set the request_limit to zero to reflect this
state. However, there is a window where the adapter may attempt to queue a
command because the transport loss event hasn't been fully processed yet
and request_limit is still greater than zero. The hypercall to send the
event will fail and the error path will increment the request_limit as a
result. If the adapter processes the transport event prior to this
increment the request_limit becomes out of sync with the adapter state and
can result in SCSI commands being submitted on the now reset connection
prior to an SRP Login resulting in a protocol violation.
Fix this race by protecting request_limit with the host lock when changing
the value via atomic_set() to indicate no transport.
The current scanning mechanism is supposed to fall back to a synchronous
host scan if an asynchronous scan is in progress. However, this rule isn't
strictly respected, scsi_prep_async_scan() doesn't hold scan_mutex when
checking shost->async_scan. When scsi_scan_host() is called concurrently,
two async scans on same host can be started and a hang in do_scan_async()
is observed.
Fixes this issue by checking & setting shost->async_scan atomically with
shost->scan_mutex.
Link: https://lore.kernel.org/r/20201010032539.426615-1-ming.lei@redhat.com Cc: Christoph Hellwig <hch@lst.de> Cc: Ewan D. Milne <emilne@redhat.com> Cc: Hannes Reinecke <hare@suse.de> Cc: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similarly to commit 457e490f2b741 ("blkcg: allocate struct blkcg_gq
outside request queue spinlock"), blkg_create can also trigger
occasional -ENOMEM failures at the radix insertion because any
allocation inside blkg_create has to be non-blocking, making it more
likely to fail. This causes trouble for userspace tools trying to
configure io weights who need to deal with this condition.
This patch reduces the occurrence of -ENOMEMs on this path by preloading
the radix tree element on a GFP_KERNEL context, such that we guarantee
the later non-blocking insertion won't fail.
A similar solution exists in blkcg_init_queue for the same situation.
When using the scaler on the A10-like frontend with single-planar formats,
the current code will setup the channel 0 filter (used for the R or Y
component) with a different phase parameter than the channel 1 filter (used
for the G/B or U/V components).
This creates a bleed out that keeps repeating on of the last line of the
RGB plane across the rest of the display. The Allwinner BSP either applies
the same phase parameter over both channels or use a separate one, the
condition being whether the input format is YUV420 or not.
Since YUV420 is both subsampled and multi-planar, and since YUYV is
subsampled but single-planar, we can rule out the subsampling and assume
that the condition is actually whether the format is single or
multi-planar. And it looks like applying the same phase parameter over both
channels for single-planar formats fixes our issue, while we keep the
multi-planar formats working properly.
The scaler filter phase setup in the allwinner kernel has two different
cases for setting up the scaler filter, the first one using different phase
parameters for the two channels, and the second one reusing the first
channel parameters on the second channel.
The allwinner kernel has a third option where the horizontal phase of the
second channel will be set to a different value than the vertical one (and
seems like it's the same value than one used on the first channel).
However, that code path seems to never be taken, so we can ignore it for
now, and it's essentially what we're doing so far as well.
Since we will have always the same values across each components of the
filter setup for a given channel, we can simplify a bit our frontend
structure by only storing the phase value we want to apply to a given
channel.
The reserved-memory overlap detection code fails to detect overlaps if
either of the regions starts at address 0x0. The code explicitly checks
for and ignores such regions, apparently in order to ignore dynamically
allocated regions which have an address of 0x0 at this point. These
dynamically allocated regions also have a size of 0x0 at this point, so
fix this by removing the check and sorting the dynamically allocated
regions ahead of any static regions at address 0x0.
For example, there are two overlaps in this case but they are not
currently reported:
kexec_file_load() currently reuses the old boot_params.screen_info,
but if drivers have change the hardware state, boot_param.screen_info
could contain invalid info.
For example, the video type might be no longer VGA, or the frame buffer
address might be changed. If the kexec kernel keeps using the old screen_info,
kexec'ed kernel may attempt to write to an invalid framebuffer
memory region.
There are two screen_info instances globally available, boot_params.screen_info
and screen_info. Later one is a copy, and is updated by drivers.
This adds the missing perpheral clock for the RNG for Amlogic G12. As
stated in amlogic,meson-rng.yaml, this isn't always necessary for the
RNG to function, but is better to have in case the clock is disabled for
some reason prior to loading.
Signed-off-by: Scott K Logan <logans@cottsay.net> Suggested-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/520a1a8ec7a958b3d918d89563ec7e93a4100a45.camel@cottsay.net Signed-off-by: Sasha Levin <sashal@kernel.org>
Gratian managed to trigger the BUG_ON(!newowner) in fixup_pi_state_owner().
This is one possible chain of events leading to this:
Task Prio Operation
T1 120 lock(F)
T2 120 lock(F) -> blocks (top waiter)
T3 50 (RT) lock(F) -> boosts T1 and blocks (new top waiter)
XX timeout/ -> wakes T2
signal
T1 50 unlock(F) -> wakes T3 (rtmutex->owner == NULL, waiter bit is set)
T2 120 cleanup -> try_to_take_mutex() fails because T3 is the top waiter
and the lower priority T2 cannot steal the lock.
-> fixup_pi_state_owner() sees newowner == NULL -> BUG_ON()
The comment states that this is invalid and rt_mutex_real_owner() must
return a non NULL owner when the trylock failed, but in case of a queued
and woken up waiter rt_mutex_real_owner() == NULL is a valid transient
state. The higher priority waiter has simply not yet managed to take over
the rtmutex.
The BUG_ON() is therefore wrong and this is just another retry condition in
fixup_pi_state_owner().
Drop the locks, so that T3 can make progress, and then try the fixup again.
Gratian provided a great analysis, traces and a reproducer. The analysis is
to the point, but it confused the hell out of that tglx dude who had to
page in all the futex horrors again. Condensed version is above.
The nesting count of trace_printk allows for 4 levels of nesting. The
nesting counter starts at zero and is incremented before being used to
retrieve the current context's buffer. But the index to the buffer uses the
nesting counter after it was incremented, and not its original number,
which in needs to do.
The work on improving gpio chip-select in spi core, and the following
fixes, has caused the bcm2835 spi driver to use wrong levels. Fix this
by simply removing level handling in the bcm2835 driver, and let the
core do its work.
Fixes: 3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS") Cc: <stable@vger.kernel.org> Signed-off-by: Martin Hundebøll <martin@geanix.com> Link: https://lore.kernel.org/r/20201014090230.2706810-1-martin@geanix.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regulator_get_voltage_rdev() is called in regulator probe() when
applying machine constraints. The "fixed" commit exposed the problem
that non-bypassed regulators can forward the request to its parent
(like bypassed ones) supply. Return -EPROBE_DEFER when the supply
is expected but not resolved yet.
Fixes: aea6cb99703e ("regulator: resolve supply after creating regulator") Cc: stable@vger.kernel.org Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Reported-by: Ondřej Jirman <megous@megous.com> Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com> Tested-by: Ondřej Jirman <megous@megous.com> Link: https://lore.kernel.org/r/a9041d68b4d35e4a2dd71629c8a6422662acb5ee.1604351936.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an interrupt or NMI comes in and switches the context, there's a delay
from when the preempt_count() shows the update. As the preempt_count() is
used to detect recursion having each context have its own bit get set when
tracing starts, and if that bit is already set, it is considered a recursion
and the function exits. But if this happens in that section where context
has changed but preempt_count() has not been updated, this will be
incorrectly flagged as a recursion.
To handle this case, create another bit call TRANSITION and test it if the
current context bit is already set. Flag the call as a recursion if the
TRANSITION bit is already set, and if not, set it and continue. The
TRANSITION bit will be cleared normally on the return of the function that
set it, or if the current context bit is clear, set it and clear the
TRANSITION bit to allow for another transition between the current context
and an even higher one.
The code that checks recursion will work to only do the recursion check once
if there's nested checks. The top one will do the check, the other nested
checks will see recursion was already checked and return zero for its "bit".
On the return side, nothing will be done if the "bit" is zero.
The problem is that zero is returned for the "good" bit when in NMI context.
This will set the bit for NMIs making it look like *all* NMI tracing is
recursing, and prevent tracing of anything in NMI context!
The simple fix is to return "bit + 1" and subtract that bit on the end to
get the real bit.
spi_nor_parse_sfdp() modifies the passed structure so that it points to
itself (params.erase_map.regions to params.erase_map.uniform_region). This
makes it impossible to copy the local struct anywhere else.
Therefore only use memcpy() in backup-restore scenario. The bug may show up
like below:
The recursion protection of the ring buffer depends on preempt_count() to be
correct. But it is possible that the ring buffer gets called after an
interrupt comes in but before it updates the preempt_count(). This will
trigger a false positive in the recursion code.
Use the same trick from the ftrace function callback recursion code which
uses a "transition" bit that gets set, to allow for a single recursion for
to handle transitions between contexts.
Cc: stable@vger.kernel.org Fixes: 567cd4da54ff4 ("ring-buffer: User context bit recursion checking") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fc0e38dae645 ("GFS2: Fix glock deallocation race") fixed a
sd_glock_disposal accounting bug by adding a missing atomic_dec
statement, but it failed to wake up sd_glock_wait when that decrement
causes sd_glock_disposal to reach zero. As a consequence,
gfs2_gl_hash_clear can now run into a 10-minute timeout instead of
being woken up. Add the missing wakeup.
The purpose of io_remap_pfn_range() is to map IO memory, such as a
memory mapped IO exposed through a PCI BAR. IO devices do not
understand encryption, so this memory must always be decrypted.
Automatically call pgprot_decrypted() as part of the generic
implementation.
This fixes a bug where enabling AMD SME causes subsystems, such as RDMA,
using io_remap_pfn_range() to expose BAR pages to user space to fail.
The CPU will encrypt access to those BAR pages instead of passing
unencrypted IO directly to the device.
Places not mapping IO should use remap_pfn_range().
Fixes: aca20d546214 ("x86/mm: Add support to make use of Secure Memory Encryption") Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: "Dave Young" <dyoung@redhat.com> Cc: Alexander Potapenko <glider@google.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Larry Woodman <lwoodman@redhat.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Ingo Molnar <mingo@kernel.org> Cc: "Michael S. Tsirkin" <mst@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Rik van Riel <riel@redhat.com> Cc: Toshimitsu Kani <toshi.kani@hpe.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/0-v1-025d64bdf6c4+e-amd_sme_fix_jgg@nvidia.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When flags in queue_pages_pte_range don't have MPOL_MF_MOVE or
MPOL_MF_MOVE_ALL bits, code breaks and passing origin pte - 1 to
pte_unmap_unlock seems like not a good idea.
queue_pages_pte_range can run in MPOL_MF_MOVE_ALL mode which doesn't
migrate misplaced pages but returns with EIO when encountering such a
page. Since commit a7f40cfe3b7a ("mm: mempolicy: make mbind() return
-EIO when MPOL_MF_STRICT is specified") and early break on the first pte
in the range results in pte_unmap_unlock on an underflow pte. This can
lead to lockups later on when somebody tries to lock the pte resp.
page_table_lock again..
Fixes: a7f40cfe3b7a ("mm: mempolicy: make mbind() return -EIO when MPOL_MF_STRICT is specified") Signed-off-by: Shijie Luo <luoshijie1@huawei.com> Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Oscar Salvador <osalvador@suse.de> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Feilong Lin <linfeilong@huawei.com> Cc: Shijie Luo <luoshijie1@huawei.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20201019074853.50856-1-luoshijie1@huawei.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Zoom UAC-2 USB audio interface provides an async playback endpoint
("1 OUT (ASYNC)") and capture endpoint ("2 IN (ASYNC)"), both with
2-channel S32_LE in 44.1, 48, 88.2, 96, 176.4, or 192
kilosamples/s. The device provides explicit feedback to adjust the
host's playback rate, but the feedback appears unstable and biased
relative to the device's capture rate.
"alsaloop -t 1000" experiences playback underruns and tries to
resample the captured audio to match the varying playback
rate. Forcing the kernel to use implicit feedback appears to
produce more stable results. This causes the host to transmit one
playback sample for each capture sample received. (Zoom North America
has been notified of this change.)
Signed-off-by: Keith Winstein <keithw@cs.stanford.edu> Tested-by: Keith Winstein <keithw@cs.stanford.edu> Cc: <stable@vger.kernel.org> BugLink: https://lore.kernel.org/r/20201027071841.GA164525@trolley.csail.mit.edu Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System boot with plugged headset. It will not detect headset Mic.
It will happen on cold boot restart resume state.
Quirk by SSID change to quirk by pin verb.
Fixes: 13468bfa8c58 ("ALSA: hda/realtek - set mic to auto detect on a HP AIO machine") Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/f42ae1ede1cf47029ae2bef1a42caf03@realtek.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6735b4632def ("Fonts: Support FONT_EXTRA_WORDS macros for built-in
fonts") introduced the following error when building rpc_defconfig (only
this build appears to be affected):
`acorndata_8x8' referenced in section `.text' of arch/arm/boot/compressed/ll_char_wr.o:
defined in discarded section `.data' of arch/arm/boot/compressed/font.o
`acorndata_8x8' referenced in section `.data.rel.ro' of arch/arm/boot/compressed/font.o:
defined in discarded section `.data' of arch/arm/boot/compressed/font.o
make[3]: *** [/scratch/linux/arch/arm/boot/compressed/Makefile:191: arch/arm/boot/compressed/vmlinux] Error 1
make[2]: *** [/scratch/linux/arch/arm/boot/Makefile:61: arch/arm/boot/compressed/vmlinux] Error 2
make[1]: *** [/scratch/linux/arch/arm/Makefile:317: zImage] Error 2
The .data section is discarded at link time. Reinstating acorndata_8x8 as
const ensures it is still available after linking. Do the same for the
other 12 built-in fonts as well, for consistency purposes.
Cc: <stable@vger.kernel.org> Cc: Russell King <linux@armlinux.org.uk> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Fixes: 6735b4632def ("Fonts: Support FONT_EXTRA_WORDS macros for built-in fonts") Signed-off-by: Lee Jones <lee.jones@linaro.org> Co-developed-by: Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20201102183242.2031659-1-yepeilin.cs@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 978aa0474115 ("sctp: fix some type cast warnings introduced since
very beginning")' broke err reading from sctp_arg, because it reads the
value as 32-bit integer, although the value is stored as 16-bit integer.
Later this value is passed to the userspace in 16-bit variable, thus the
user always gets 0 on big-endian platforms. Fix it by reading the __u16
field of sctp_arg union, as reading err field would produce a sparse
warning.
Fixes: 978aa0474115 ("sctp: fix some type cast warnings introduced since very beginning") Signed-off-by: Petr Malat <oss@malat.biz> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Link: https://lore.kernel.org/r/20201030132633.7045-1-oss@malat.biz Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5a18e1e0c193b introduced the 'failover_pending' state to track
the "failover pending window" - where we wait for the partner to become
ready (after a transport event) before actually attempting to failover.
i.e window is between following two events:
a. we get a transport event due to a FAILOVER
b. later, we get CRQ_INITIALIZED indicating the partner is
ready at which point we schedule a FAILOVER reset.
and ->failover_pending is true during this window.
If during this window, we attempt to open (or close) a device, we pretend
that the operation succeded and let the FAILOVER reset path complete the
operation.
This is fine, except if the transport event ("a" above) occurs during the
open and after open has already checked whether a failover is pending. If
that happens, we fail the open, which can cause the boot scripts to leave
the interface down requiring administrator to manually bring up the device.
This fix "extends" the failover pending window till we are _actually_
ready to perform the failover reset (i.e until after we get the RTNL
lock). Since open() holds the RTNL lock, we can be sure that we either
finish the open or if the open() fails due to the failover pending window,
we can again pretend that open is done and let the failover complete it.
We could try and block the open until failover is completed but a) that
could still timeout the application and b) Existing code "pretends" that
failover occurred "just after" open succeeded, so marks the open successful
and lets the failover complete the open. So, mark the open successful even
if the transport event occurs before we actually start the open.
Fixes: 5a18e1e0c193 ("ibmvnic: Fix failover case for non-redundant configuration") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Acked-by: Dany Madden <drt@linux.ibm.com> Link: https://lore.kernel.org/r/20201030170711.1562994-1-sukadev@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tunnel device such as vxlan, bareudp and geneve in the lwt mode set
the outer df only based TUNNEL_DONT_FRAGMENT.
And this was also the behavior for gre device before switching to use
ip_md_tunnel_xmit in commit 962924fa2b7a ("ip_gre: Refactor collect
metatdata mode tunnel xmit to ip_md_tunnel_xmit")
When the ip_gre in lwt mode xmit with ip_md_tunnel_xmi changed the rule and
make the discrepancy between handling of DF by different tunnels. So in the
ip_md_tunnel_xmit should follow the same rule like other tunnels.
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on the second option,
using skb_realloc_headroom() to create a new skb to accommodate
PTP frames. Turns out that this method is not reliable, as
reallocation of skbs for PTP frames along with the required
overhead (skb_set_owner_w, consume_skb) is causing random
crashes in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time on the same device
(as seen in James' report).
Note that these crashes don't occur with a single TCP stream,
nor with multiple concurrent UDP streams, but only when multiple
TCP streams are run concurrently with the PTP packet flow
(doing skb reallocation).
This patch enforces the first method, by requesting enough
headroom from the stack to accommodate PTP frames, and so avoiding
skb_realloc_headroom() & co, and the crashes no longer occur.
There's no reason not to set needed_headroom to a large enough
value to accommodate PTP frames, so in this regard this patch
is a fix.
Reported-by: James Jurack <james.jurack@ametek.com> Fixes: bee9e58c9e98 ("gianfar:don't add FCB length to hard_header_len") Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20201020173605.1173-1-claudiu.manoil@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PTP timestamping is enabled on Tx, the controller
inserts the Tx timestamp at the beginning of the frame
buffer, between SFD and the L2 frame header. This means
that the skb provided by the stack is required to have
enough headroom otherwise a new skb needs to be created
by the driver to accommodate the timestamp inserted by h/w.
Up until now the driver was relying on skb_realloc_headroom()
to create new skbs to accommodate PTP frames. Turns out that
this method is not reliable in this context at least, as
skb_realloc_headroom() for PTP frames can cause random crashes,
mostly in subsequent skb_*() calls, when multiple concurrent
TCP streams are run at the same time with the PTP flow
on the same device (as seen in James' report). I also noticed
that when the system is loaded by sending multiple TCP streams,
the driver receives cloned skbs in large numbers.
skb_cow_head() instead proves to be stable in this scenario,
and not only handles cloned skbs too but it's also more efficient
and widely used in other drivers.
The commit introducing skb_realloc_headroom in the driver
goes back to 2009, commit 93c1285c5d92
("gianfar: reallocate skb when headroom is not enough for fcb").
For practical purposes I'm referencing a newer commit (from 2012)
that brings the code to its current structure (and fixes the PTP
case).
Fixes: 9c4886e5e63b ("gianfar: Fix invalid TX frames returned on error queue when time stamping") Reported-by: James Jurack <james.jurack@ametek.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20201029081057.8506-1-claudiu.manoil@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct skb refcount in alloc_ctrl_skb(), causing skb memleak
when chtls_send_abort() called with NULL skb.
it was always leaking the skb, correct it by incrementing skb
refs by one.
work request skb queued in chtls_setkey() won't be freed
because resources are already cleaned for this connection,
fix it by not queuing work request while socket is closing.
v1->v2:
- fix W=1 warning.
v2->v3:
- separate it out from another memleak fix.
In my test setup, I had a SAMA5D27 device configured with ip forwarding, and
second device with usb ethernet (r8152) sending ICMP packets. If the packet
was larger than about 220 bytes, the SAMA5 device would "oops" with the
following trace:
kernel BUG at net/core/skbuff.c:1863!
Internal error: Oops - BUG: 0 [#1] ARM
Modules linked in: xt_MASQUERADE ppp_async ppp_generic slhc iptable_nat xt_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 can_raw can bridge stp llc ipt_REJECT nf_reject_ipv4 sd_mod cdc_ether usbnet usb_storage r8152 scsi_mod mii o
ption usb_wwan usbserial micrel macb at91_sama5d2_adc phylink gpio_sama5d2_piobu m_can_platform m_can industrialio_triggered_buffer kfifo_buf of_mdio can_dev fixed_phy sdhci_of_at91 sdhci_pltfm libphy sdhci mmc_core ohci_at91 ehci_atmel o
hci_hcd iio_rescale industrialio sch_fq_codel spidev prox2_hal(O)
CPU: 0 PID: 0 Comm: swapper Tainted: G O 5.9.1-prox2+ #1
Hardware name: Atmel SAMA5
PC is at skb_put+0x3c/0x50
LR is at macb_start_xmit+0x134/0xad0 [macb]
pc : [<c05258cc>] lr : [<bf0ea5b8>] psr: 20070113
sp : c0d01a60 ip : c07232c0 fp : c4250000
r10: c0d03cc8 r9 : 00000000 r8 : c0d038c0
r7 : 00000000 r6 : 00000008 r5 : c59b66c0 r4 : 0000002a
r3 : 8f659eff r2 : c59e9eea r1 : 00000001 r0 : c59b66c0
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c53c7d Table: 2640c059 DAC: 00000051
Process swapper (pid: 0, stack limit = 0x75002d81)
The solution was to force nonlinear buffers to be cloned. This was previously
reported by Klaus Doth (https://www.spinics.net/lists/netdev/msg556937.html)
but never formally submitted as a patch.
This is the third revision, hopefully the formatting is correct this time!
Suggested-by: Klaus Doth <krnl@doth.eu> Fixes: 653e92a9175e ("net: macb: add support for padding and fcs computation") Signed-off-by: Mark Deneen <mdeneen@saucontech.com> Link: https://lore.kernel.org/r/20201030155814.622831-1-mdeneen@saucontech.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
int status;
int thread = waitpid(-1, &status, 0);
assert(thread > 0 && thread != pid);
assert(status == 0x80137f);
return 0;
}
fails and triggers WARN_ON_ONCE(!signr) in do_jobctl_trap().
This is because task_join_group_stop() has 2 problems when current is traced:
1. We can't rely on the "JOBCTL_STOP_PENDING" check, a stopped tracee
can be woken up by debugger and it can clone another thread which
should join the group-stop.
We need to check group_stop_count || SIGNAL_STOP_STOPPED.
2. If SIGNAL_STOP_STOPPED is already set, we should not increment
sig->group_stop_count and add JOBCTL_STOP_CONSUME. The new thread
should stop without another do_notify_parent_cldstop() report.
To clarify, the problem is very old and we should blame
ptrace_init_task(). But now that we have task_join_group_stop() it makes
more sense to fix this helper to avoid the code duplication.
==================================================================
BUG: KASAN: use-after-free in tipc_bcast_get_mode+0x3ab/0x400 net/tipc/bcast.c:759
Read of size 1 at addr ffff88805e6b3571 by task kworker/0:6/3850
CPU: 0 PID: 3850 Comm: kworker/0:6 Not tainted 5.8.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events tipc_net_finalize_work
Fix it by calling flush_scheduled_work() to make sure the
tipc_net_finalize_work() stopped before releasing bcbase object.
Reported-by: syzbot+6ea1f7a8df64596ef4d7@syzkaller.appspotmail.com Reported-by: syzbot+e9cc557752ab126c1b99@syzkaller.appspotmail.com Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 39d114ddc682 ("arm64: add KASAN support") added .weak directives to
arch/arm64/lib/mem*.S instead of changing the existing SYM_FUNC_START_PI
macros. This can lead to the assembly snippet `.weak memcpy ... .globl
memcpy` which will produce a STB_WEAK memcpy with GNU as but STB_GLOBAL
memcpy with LLVM's integrated assembler before LLVM 12. LLVM 12 (since
https://reviews.llvm.org/D90108) will error on such an overridden symbol
binding.
Use the appropriate SYM_FUNC_START_WEAK_PI instead.
Fixes: 39d114ddc682 ("arm64: add KASAN support") Reported-by: Sami Tolvanen <samitolvanen@google.com> Signed-off-by: Fangrui Song <maskray@google.com> Tested-by: Sami Tolvanen <samitolvanen@google.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201029181951.1866093-1-maskray@google.com Signed-off-by: Will Deacon <will@kernel.org> Cc: Jian Cai <jiancai@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In an effort to clarify and simplify the annotation of assembly functions
in the kernel new macros have been introduced. These replace ENTRY and
ENDPROC and also add a new annotation for static functions which previously
had no ENTRY equivalent. Update the annotations in the library code to the
new macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
[will: Use SYM_FUNC_START_WEAK_PI] Signed-off-by: Will Deacon <will@kernel.org> Cc: Jian Cai <jiancai@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of an effort to make the annotations in assembly code clearer and
more consistent new macros have been introduced, including replacements
for ENTRY() and ENDPROC().
On arm64 we have ENDPIPROC(), a custom version of ENDPROC() which is
used for code that will need to run in position independent environments
like EFI, it creates an alias for the function with the prefix __pi_ and
then emits the standard ENDPROC. Add new-style macros to replace this
which expand to the standard SYM_FUNC_*() and SYM_FUNC_ALIAS_*(),
resulting in the same object code. These are added in linkage.h for
consistency with where the generic assembler code has its macros.
Signed-off-by: Mark Brown <broonie@kernel.org>
[will: Rename 'WEAK' macro, use ';' instead of ASM_NL, deprecate ENDPIPROC] Signed-off-by: Will Deacon <will@kernel.org> Cc: Jian Cai <jiancai@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce new C macros for annotations of functions and data in
assembly. There is a long-standing mess in macros like ENTRY, END,
ENDPROC and similar. They are used in different manners and sometimes
incorrectly.
So introduce macros with clear use to annotate assembly as follows:
a) Support macros for the ones below
SYM_T_FUNC -- type used by assembler to mark functions
SYM_T_OBJECT -- type used by assembler to mark data
SYM_T_NONE -- type used by assembler to mark entries of unknown type
They are defined as STT_FUNC, STT_OBJECT, and STT_NOTYPE
respectively. According to the gas manual, this is the most portable
way. I am not sure about other assemblers, so this can be switched
back to %function and %object if this turns into a problem.
Architectures can also override them by something like ", @function"
if they need.
SYM_A_ALIGN, SYM_A_NONE -- align the symbol?
SYM_L_GLOBAL, SYM_L_WEAK, SYM_L_LOCAL -- linkage of symbols
b) Mostly internal annotations, used by the ones below
SYM_ENTRY -- use only if you have to (for non-paired symbols)
SYM_START -- use only if you have to (for paired symbols)
SYM_END -- use only if you have to (for paired symbols)
c) Annotations for code
SYM_INNER_LABEL_ALIGN -- only for labels in the middle of code
SYM_INNER_LABEL -- only for labels in the middle of code
SYM_FUNC_START_LOCAL_ALIAS -- use where there are two local names for
one function
SYM_FUNC_START_ALIAS -- use where there are two global names for one
function
SYM_FUNC_END_ALIAS -- the end of LOCAL_ALIASed or ALIASed function
SYM_FUNC_START -- use for global functions
SYM_FUNC_START_NOALIGN -- use for global functions, w/o alignment
SYM_FUNC_START_LOCAL -- use for local functions
SYM_FUNC_START_LOCAL_NOALIGN -- use for local functions, w/o
alignment
SYM_FUNC_START_WEAK -- use for weak functions
SYM_FUNC_START_WEAK_NOALIGN -- use for weak functions, w/o alignment
SYM_FUNC_END -- the end of SYM_FUNC_START_LOCAL, SYM_FUNC_START,
SYM_FUNC_START_WEAK, ...
For functions with special (non-C) calling conventions:
SYM_CODE_START -- use for non-C (special) functions
SYM_CODE_START_NOALIGN -- use for non-C (special) functions, w/o
alignment
SYM_CODE_START_LOCAL -- use for local non-C (special) functions
SYM_CODE_START_LOCAL_NOALIGN -- use for local non-C (special)
functions, w/o alignment
SYM_CODE_END -- the end of SYM_CODE_START_LOCAL or SYM_CODE_START
d) For data
SYM_DATA_START -- global data symbol
SYM_DATA_START_LOCAL -- local data symbol
SYM_DATA_END -- the end of the SYM_DATA_START symbol
SYM_DATA_END_LABEL -- the labeled end of SYM_DATA_START symbol
SYM_DATA -- start+end wrapper around simple global data
SYM_DATA_LOCAL -- start+end wrapper around simple local data
==========
The macros allow to pair starts and ends of functions and mark functions
correctly in the output ELF objects.
All users of the old macros in x86 are converted to use these in further
patches.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Juergen Gross <jgross@suse.com> Cc: Len Brown <len.brown@intel.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: linux-arch@vger.kernel.org Cc: linux-doc@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: linux-pm@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will@kernel.org> Cc: x86-ml <x86@kernel.org> Cc: xen-devel@lists.xenproject.org Link: https://lkml.kernel.org/r/20191011115108.12392-2-jslaby@suse.cz Cc: Jian Cai <jiancai@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add alternative topology binary file name based on used machine driver
and fallback to use this name after failed attempt to load topology file
with name based on NHLT.
This change addresses multiple issues with current mechanism, for
example - there are devices without NHLT table, and that currently
results in tplg_name being empty.
The "mmio" writes into vgpu registers are simple memory traps from the
guest into the host. We do not need to assert in the guest that the
device is awake for the io as we do not write to the device itself.
However, over time we have refactored all the mmio accessors with the
result that the vgpu reuses the gen2 accessors and so inherits the
assert for runtime-pm of the native device. The assert though has
actually been there since commit 3be0bf5acca6 ("drm/i915: Create vGPU
specific MMIO operations to reduce traps").
References: 3be0bf5acca6 ("drm/i915: Create vGPU specific MMIO operations to reduce traps") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Yan Zhao <yan.y.zhao@intel.com> Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20200811092532.13753-1-chris@chris-wilson.co.uk
(cherry picked from commit 0e65ce24a33c1d37da4bf43c34e080334ec6cb60) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running gem_exec_nop, it floods the system with many requests (with
the goal of userspace submitting faster than the HW can process a single
empty batch). This causes the driver to continually resubmit new
requests onto the end of an active context, a flood of lite-restore
preemptions. If we time this just right, Tigerlake hangs.
Inserting a small delay between the processing of CS events and
submitting the next context, prevents the hang. Naturally it does not
occur with debugging enabled. The suspicion then is that this is related
to the issues with the CS event buffer, and inserting an mmio read of
the CS pointer status appears to be very successful in preventing the
hang. Other registers, or uncached reads, or plain mb, do not prevent
the hang, suggesting that register is key -- but that the hang can be
prevented by a simple udelay, suggests it is just a timing issue like
that encountered by commit 233c1ae3c83f ("drm/i915/gt: Wait for CSB
entries on Tigerlake"). Also note that the hang is not prevented by
applying CTX_DESC_FORCE_RESTORE, or by inserting a delay on the GPU
between requests.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Bruce Chang <yu.bruce.chang@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: stable@vger.kernel.org Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201015195023.32346-1-chris@chris-wilson.co.uk
(cherry picked from commit 6ca7217dffaf1abba91558e67a2efb655ac91405) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the error capture will compress user buffers as directed to by the
user, it can take an arbitrary amount of time and space. Break up the
compression loops with a call to cond_resched(), that will allow other
processes to schedule (avoiding the soft lockups) and also serve as a
warning should we try to make this loop atomic in the future.
Currently in case of alignment or FCS error if the packet cannot be
corrected it's still not dropped. Report the error properly and drop the
packet while making the code around a little bit more readable.
The "cb_pcidas" driver supports asynchronous commands on the analog
output (AO) subdevice for those boards that have an AO FIFO. The code
(in `cb_pcidas_ao_check_chanlist()` and `cb_pcidas_ao_cmd()`) to
validate and set up the command supports output to a single channel or
to two channels simultaneously (the boards have two AO channels).
However, the code in `cb_pcidas_auto_attach()` that initializes the
subdevices neglects to initialize the AO subdevice's `len_chanlist`
member, leaving it set to 0, but the Comedi core will "correct" it to 1
if the driver neglected to set it. This limits commands to use a single
channel (either channel 0 or 1), but the limit should be two channels.
Set the AO subdevice's `len_chanlist` member to be the same value as the
`n_chan` member, which will be 2.
The DBGD{CCINT,SCRext} and DBGVCR register entries in the cp14 array
are missing their target register, resulting in all accesses being
targetted at the guard sysreg (indexed by __INVALID_SYSREG__).
Point the emulation code at the actual register entries.
It appears that firmware nodes can be shared between devices. In such case
when a (child) device is about to be deleted, its firmware node may be shared
and ACPI_COMPANION_SET(..., NULL) call for it breaks the secondary link
of the shared primary firmware node.
In order to prevent that, check, if the device has a parent and parent's
firmware node is shared with its child, and avoid crashing the link.
Fixes: c15e1bdda436 ("device property: Fix the secondary firmware node handling in set_primary_fwnode()") Reported-by: Ferry Toth <fntoth@gmail.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Ferry Toth <fntoth@gmail.com> Cc: 5.9+ <stable@vger.kernel.org> # 5.9+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Behind primary and secondary we understand the type of the nodes
which might define their ordering. However, if primary node gone,
we can't maintain the ordering by definition of the linked list.
Thus, by ordering secondary node becomes first in the list.
But in this case the meaning of it is still secondary (or auxiliary).
The type of the node is maintained by the secondary pointer in it:
secondary pointer Meaning
NULL or valid primary node
ERR_PTR(-ENODEV) secondary node
So, if by some reason we do the following sequence of calls
This concept is supported by the description of set_primary_fwnode()
along with implementation of set_secondary_fwnode(). Hence, fix
the commit c15e1bdda436 to follow this as well.
Fixes: c15e1bdda436 ("device property: Fix the secondary firmware node handling in set_primary_fwnode()") Cc: Ferry Toth <fntoth@gmail.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Tested-by: Ferry Toth <fntoth@gmail.com> Cc: 5.9+ <stable@vger.kernel.org> # 5.9+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f6361c6b3880 ("ARM: S3C24XX: remove separate restart code")
removed usage of the watchdog reset platform code in favor of the
Samsung SoC watchdog driver. However the latter was not selected thus
S3C24xx platforms lost reset abilities.
Cc: <stable@vger.kernel.org> Fixes: f6361c6b3880 ("ARM: S3C24XX: remove separate restart code") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Selecting CONFIG_SAMSUNG_PM_DEBUG (depending on CONFIG_DEBUG_LL) but
without CONFIG_MMU leads to build errors:
arch/arm/plat-samsung/pm-debug.c: In function ‘s3c_pm_uart_base’:
arch/arm/plat-samsung/pm-debug.c:57:2: error:
implicit declaration of function ‘debug_ll_addr’ [-Werror=implicit-function-declaration]
Fixes: 99b2fc2b8b40 ("ARM: SAMSUNG: Use debug_ll_addr() to get UART base address") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200910154150.3318-1-krzk@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When starting a HP machine with HIL driver but without an HIL keyboard
or HIL mouse attached, it may happen that data written to the HIL loop
gets stuck (e.g. because the transaction queue is full). Usually one
will then have to reboot the machine because all you see is and endless
output of:
Transaction add failed: transaction already queued?
In the higher layers hp_sdc_enqueue_transaction() is called to queued up
a HIL packet. This function returns an error code, and this patch adds
the necessary checks for this return code and disables the HIL driver if
further packets can't be sent.
projects / linux-stable / log