The problem is the check introduced to for_each_hstate() loop that
should skip default_hstate_idx. Since it doesn't update 'i' counter,
all subsequent huge page sizes are skipped as well.
Fixes: 8fc312b32b25 ("mm/hugetlbfs: fix error handling when setting up mounts") Signed-off-by: Jan Stancek <jstancek@redhat.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous patch implemented an incomplete workaround of erratum
A-008171. The complete workaround is as below. This patch is to
implement the complete workaround which uses SW tuning if HW tuning
fails, and retries both HW/SW tuning once with reduced clock if
workaround fails. This is suggested by hardware team, and the patch
had been verified on LS1046A eSDHC + Phison 32G eMMC which could
trigger the erratum.
Workaround:
/* For T1040, T2080, LS1021A, T1023 Rev 1: */
1. Program TBPTR[TB_WNDW_END_PTR] = 3*DIV_RATIO.
2. Program TBPTR[TB_WNDW_START_PTR] = 5*DIV_RATIO.
3. Program the software tuning mode by setting TBCTL[TB_MODE] = 2'h3.
4. Set SYSCTL2[EXTN] and SYSCTL2[SAMPCLKSEL].
5. Issue SEND_TUNING_BLK Command (CMD19 for SD, CMD21 for MMC).
6. Wait for IRQSTAT[BRR], buffer read ready, to be set.
7. Clear IRQSTAT[BRR].
8. Check SYSCTL2[EXTN] to be cleared.
9. Check SYSCTL2[SAMPCLKSEL], Sampling Clock Select. It's set value
indicate tuning procedure success, and clear indicate failure.
In case of tuning failure, fixed sampling scheme could be used by
clearing TBCTL[TB_EN].
/* For LS1080A Rev 1, LS2088A Rev 1.0, LA1575A Rev 1.0: */
1. Read the TBCTL[31:0] register. Write TBCTL[11:8]=4'h8 and wait for
1ms.
2. Read the TBCTL[31:0] register and rewrite again. Wait for 1ms second.
3. Read the TBSTAT[31:0] register twice.
3.1 Reset data lines by setting ESDHCCTL[RSTD] bit.
3.2 Check ESDHCCTL[RSTD] bit.
3.3 If ESDHCCTL[RSTD] is 0, go to step 3.4 else go to step 3.2.
3.4 Write 32'hFFFF_FFFF to IRQSTAT register.
4. if TBSTAT[15:8]-TBSTAT[7:0] > 4*DIV_RATIO or TBSTAT[7:0]-TBSTAT[15:8]
> 4*DIV_RATIO , then program TBPTR[TB_WNDW_END_PTR] = 4*DIV_RATIO and
program TBPTR[TB_WNDW_START_PTR] = 8*DIV_RATIO.
/* For LS1012A Rev1, LS1043A Rev 1.x, LS1046A 1.0: */
1. Read the TBCTL[0:31] register. Write TBCTL[20:23]=4'h8 and wait for
1ms.
2. Read the TBCTL[0:31] register and rewrite again. Wait for 1ms second.
3. Read the TBSTAT[0:31] register twice.
3.1 Reset data lines by setting ESDHCCTL[RSTD] bit.
3.2 Check ESDHCCTL[RSTD] bit.
3.3 If ESDHCCTL[RSTD] is 0, go to step 3.4 else go to step 3.2.
3.4 Write 32'hFFFF_FFFF to IRQSTAT register.
4. if TBSTAT[16:23]-TBSTAT[24:31] > 4*DIV_RATIO or TBSTAT[24:31]-
TBSTAT[16:23] > 4* DIV_RATIO , then program TBPTR[TB_WNDW_END_PTR] =
4*DIV_RATIO and program TBPTR[TB_WNDW_START_PTR] = 8*DIV_RATIO.
/* For LS1080A Rev 1, LS2088A Rev 1.0, LA1575A Rev 1.0 LS1012A Rev1,
* LS1043A Rev 1.x, LS1046A 1.0:
*/
5. else program TBPTR[TB_WNDW_END_PTR] = 3*DIV_RATIO and program
TBPTR[TB_WNDW_START_PTR] = 5*DIV_RATIO.
6. Program the software tuning mode by setting TBCTL[TB_MODE] = 2'h3.
7. Set SYSCTL2[EXTN], wait 1us and SYSCTL2[SAMPCLKSEL].
8. Issue SEND_TUNING_BLK Command (CMD19 for SD, CMD21 for MMC).
9. Wait for IRQSTAT[BRR], buffer read ready, to be set.
10. Clear IRQSTAT[BRR].
11. Check SYSCTL2[EXTN] to be cleared.
12. Check SYSCTL2[SAMPCLKSEL], Sampling Clock Select. It's set value
indicate tuning procedure success, and clear indicate failure.
In case of tuning failure, fixed sampling scheme could be used by
clearing TBCTL[TB_EN].
When we receive a new packet from the guest, we check if the
src_cid is correct, but we forgot to check the dst_cid.
The host should accept only packets where dst_cid is
equal to the host CID.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In netpoll the napi handler could be called with budget equal to zero.
Current ENA napi handler doesn't take that into consideration.
The napi handler handles Rx packets in a do-while loop.
Currently, the budget check happens only after decrementing the
budget, therefore the napi handler, in rare cases, could run over
MAX_INT packets.
In addition to that, this moves all budget related variables to int
calculation and stop mixing u32 to avoid ambiguity
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)") Signed-off-by: Netanel Belgazal <netanel@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 4b1373de73a3 ("net: ipv6: addr: perform strict checks also for
doit handlers") we add strict check for inet6_rtm_getaddr(). But we did
the invalid header values check before checking if NETLINK_F_STRICT_CHK
is set. This may break backwards compatibility if user already set the
ifm->ifa_prefixlen, ifm->ifa_flags, ifm->ifa_scope in their netlink code.
I didn't move the nlmsg_len check because I thought it's a valid check.
Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 4b1373de73a3 ("net: ipv6: addr: perform strict checks also for doit handlers") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After executing "ethtool -C eth0 rx-usecs-irq 0", the box becomes
unresponsive, likely due to interrupt livelock. It appears that
a minimum clamp value for the irq timer is computed, but is never
applied.
Fix by applying the corrected clamp value.
Fixes: 74706afa712d ("bnxt_en: Update interrupt coalescing logic.") Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GTP RX packet path lookups pdp context with TID. If duplicate TID pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, TID value should be unique.
GTP TX packet path lookups pdp context with ms_addr. If duplicate ms_addr pdp
contexts are existing in the list, it couldn't select correct pdp context.
So, ms_addr value should be unique.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipv4_pdp_find() is called in TX packet path of GTP.
ipv4_pdp_find() internally uses gtp->tid_hash to lookup pdp context.
In the current code, gtp->tid_hash and gtp->addr_hash are freed by
->dellink(), which is gtp_dellink().
But gtp_dellink() would be called while packets are processing.
So, gtp_dellink() should not free gtp->tid_hash and gtp->addr_hash.
Instead, dev->priv_destructor() would be used because this callback
is called after all packet processing safely.
Test commands:
ip link add veth1 type veth peer name veth2
ip a a 172.0.0.1/24 dev veth1
ip link set veth1 up
ip a a 172.99.0.1/32 dev lo
gtp-link add gtp1 &
gtp-tunnel add gtp1 v1 200 100 172.99.0.2 172.0.0.2
ip r a 172.99.0.2/32 dev gtp1
ip link set gtp1 mtu 1500
ip netns add ns2
ip link set veth2 netns ns2
ip netns exec ns2 ip a a 172.0.0.2/24 dev veth2
ip netns exec ns2 ip link set veth2 up
ip netns exec ns2 ip a a 172.99.0.2/32 dev lo
ip netns exec ns2 ip link set lo up
ip netns exec ns2 gtp-link add gtp2 &
ip netns exec ns2 gtp-tunnel add gtp2 v1 100 200 172.99.0.1 172.0.0.1
ip netns exec ns2 ip r a 172.99.0.1/32 dev gtp2
ip netns exec ns2 ip link set gtp2 mtu 1500
Host can provide send indirection table messages anytime after RSS is
enabled by calling rndis_filter_set_rss_param(). So the host provided
table values may be overwritten by the initialization in
rndis_set_subchannel().
To prevent this problem, move the tx_table initialization before calling
rndis_filter_set_rss_param().
Fixes: a6fb6aa3cfa9 ("hv_netvsc: Set tx_table to equal weight after subchannels open") Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Kubecek and Firo Yang did a very nice analysis of crashes
happening in __inet_lookup_established().
Since a TCP socket can go from TCP_ESTABLISH to TCP_LISTEN
(via a close()/socket()/listen() cycle) without a RCU grace period,
I should not have changed listeners linkage in their hash table.
They must use the nulls protocol (Documentation/RCU/rculist_nulls.txt),
so that a lookup can detect a socket in a hash list was moved in
another one.
Since we added code in commit d296ba60d8e2 ("soreuseport: Resolve
merge conflict for v4/v6 ordering fix"), we have to add
hlist_nulls_add_tail_rcu() helper.
Fixes: 3b24d854cb35 ("tcp/dccp: do not touch listener sk_refcnt under synflood") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Michal Kubecek <mkubecek@suse.cz> Reported-by: Firo Yang <firo.yang@suse.com> Reviewed-by: Michal Kubecek <mkubecek@suse.cz> Link: https://lore.kernel.org/netdev/20191120083919.GH27852@unicorn.suse.cz/ Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Backport of commit fdfc5c8594c2 ("tcp: remove empty skb from
write queue in error cases") in linux-4.14 stable triggered
various bugs. One of them has been fixed in commit ba2ddb43f270
("tcp: Don't dequeue SYN/FIN-segments from write-queue"), but
we still have crashes in some occasions.
Root-cause is that when tcp_sendmsg() has allocated a fresh
skb and could not append a fragment before being blocked
in sk_stream_wait_memory(), tcp_write_xmit() might be called
and decide to send this fresh and empty skb.
Sending an empty packet is not only silly, it might have caused
many issues we had in the past with tp->packets_out being
out of sync.
Fixes: c65f7f00c587 ("[TCP]: Simplify SKB data portion allocation with NETIF_F_SG.") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Christoph Paasch <cpaasch@apple.com> Acked-by: Neal Cardwell <ncardwell@google.com> Cc: Jason Baron <jbaron@akamai.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the recent fix in commit 1899bb325149 ("bonding: fix state
transition issue in link monitoring"), the active-backup mode with
miimon initially come-up fine but after a link-failure, both members
transition into backup state.
Following steps to reproduce the scenario (eth1 and eth2 are the
slaves of the bond):
ip link set eth1 up
ip link set eth2 down
sleep 1
ip link set eth2 up
ip link set eth1 down
cat /sys/class/net/eth1/bonding_slave/state
cat /sys/class/net/eth2/bonding_slave/state
Fixes: 1899bb325149 ("bonding: fix state transition issue in link monitoring") CC: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Mahesh Bandewar <maheshb@google.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GTP default hashtable size is 1024 and userspace could set specific
hashtable size with IFLA_GTP_PDP_HASHSIZE. If hashtable size is set to 0
from userspace, hashtable will not work and panic will occur.
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gtp_genl_dump_pdp() is ->dumpit() callback of GTP module and it is used
to dump pdp contexts. it would be re-executed because of dump packet size.
If dump packet size is too big, it saves current dump pointer
(gtp interface pointer, bucket, TID value) then it restarts dump from
last pointer.
Current GTP code allows adding zero TID pdp context but dump code
ignores zero TID value. So, last dump pointer will not be found.
In addition, this patch adds missing rcu_read_lock() in
gtp_genl_dump_pdp().
Fixes: 459aa660eb1d ("gtp: add initial driver for datapath of GPRS Tunneling Protocol (GTP-U)") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
phylink requires the MAC to report when its link status changes when
operating in inband modes. Failure to report link status changes
means that phylink has no idea when the link events happen, which
results in either the network interface's carrier remaining up or
remaining permanently down.
For example, with a fiber module, if the interface is brought up and
link is initially established, taking the link down at the far end
will cut the optical power. The SFP module's LOS asserts, we
deactivate the link, and the network interface reports no carrier.
When the far end is brought back up, the SFP module's LOS deasserts,
but the MAC may be slower to establish link. If this happens (which
in my tests is a certainty) then phylink never hears that the MAC
has established link with the far end, and the network interface is
stuck reporting no carrier. This means the interface is
non-functional.
Avoiding the link interrupt when we have phylink is basically not
an option, so remove the !port->phylink from the test.
Fixes: 4bb043262878 ("net: mvpp2: phylink support") Tested-by: Sven Auhagen <sven.auhagen@voleatech.de> Tested-by: Antoine Tenart <antoine.tenart@bootlin.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c0d ("net: dsa: sja1105: Reverse TPID and TPID2") Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
So disable the neigh confirm for vxlan and geneve pmtu update.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: a93bf0ff4490 ("vxlan: update skb dst pmtu on tx path") Fixes: 52a589d51f10 ("geneve: update skb dst pmtu on tx path") Reviewed-by: Guillaume Nault <gnault@redhat.com> Tested-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although vti and vti6 are immune to this problem because they are IFF_NOARP
interfaces, as Guillaume pointed. There is still no sense to confirm neighbour
here.
v5: Update commit description.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No Change.
v4: Update commit description
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: 0dec879f636f ("net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP") Reviewed-by: Guillaume Nault <gnault@redhat.com> Tested-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new function skb_dst_update_pmtu_no_confirm() for callers who need
update pmtu but should not do neighbor confirm.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although GTP only support ipv4 right now, and __ip_rt_update_pmtu() does not
call dst_confirm_neigh(), we still set it to false to keep consistency with
IPv6 code.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we do ipv6 gre pmtu update, we will also do neigh confirm currently.
This will cause the neigh cache be refreshed and set to REACHABLE before
xmit.
But if the remote mac address changed, e.g. device is deleted and recreated,
we will not able to notice this and still use the old mac address as the neigh
cache is REACHABLE.
Fix this by disable neigh confirm when do pmtu update
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reported-by: Jianlin Shi <jishi@redhat.com> Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net> Reviewed-by: Guillaume Nault <gnault@redhat.com> Acked-by: David Ahern <dsahern@gmail.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes: 11566d34f895 ("mlxsw: spectrum: Add VRRP traps") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Alex Veber <alexve@mellanox.com> Tested-by: Alex Veber <alexve@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.
Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.
Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:
Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.
Fix this by skipping loopback RIFs during MAC validation.
Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses") Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VF driver also needs to create the health reporters since
VFs are also involved in firmware reset and recovery. Modify
bnxt_dl_register() and bnxt_dl_unregister() so that they can
be called by the VFs to register/unregister devlink. Only the PF
will register the devlink parameters. With devlink registered,
we can now create the health reporters on the VFs.
Fixes: 6763c779c2d8 ("bnxt_en: Add new FW devlink_health_reporter") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the logic to properly check the fw capabilities and create the
devlink health reporters only when needed. The current code creates
the reporters unconditionally as long as bp->fw_health is valid, and
that's not correct.
Call bnxt_dl_fw_reporters_create() directly from the init and reset
code path instead of from bnxt_dl_register(). This allows the
reporters to be adjusted when capabilities change. The same
applies to bnxt_dl_fw_reporters_destroy().
Fixes: 6763c779c2d8 ("bnxt_en: Add new FW devlink_health_reporter") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After fixing the allocation of bp->fw_health in the previous patch,
the driver will not go through the fw reset and recovery code paths
if bp->fw_health allocation fails. So we can now remove the
unnecessary NULL checks.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bp->fw_health needs to be allocated for either the firmware initiated
reset feature or the driver initiated error recovery feature. The
current code is not allocating bp->fw_health for all the necessary cases.
This patch corrects the logic to allocate bp->fw_health correctly when
needed. If allocation fails, we clear the feature flags.
We also add the the missing kfree(bp->fw_health) when the driver is
unloaded. If we get an async reset message from the firmware, we also
need to make sure that we have a valid bp->fw_health before proceeding.
Fixes: 07f83d72d238 ("bnxt_en: Discover firmware error recovery capabilities.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any change happened in the configuration of VF in VM while
collecting live dump, there could be a race and firmware can return
more data than allocated dump length. Fix it by keeping track of
the accumulated core dump length copied so far and abort the copy
with error code if the next chunk of core dump will exceed the
original dump length.
Fixes: 6c5657d085ae ("bnxt_en: Add support for ethtool get dump.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will trigger new context memory to be rediscovered and allocated
during the re-probe process after a firmware reset. Without this, the
newly reset firmware does not have valid context memory and the driver
will eventually fail to allocate some resources.
Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The logic needs to check both bp->total_irqs and the reserved IRQs in
hw_resc->resv_irqs if applicable and see if both are enough to cover
the L2 and RDMA requested vectors. The current code is only checking
bp->total_irqs and can fail in some code paths, such as the TX timeout
code path with the RDMA driver requesting vectors after recovery. In
this code path, we have not reserved enough MSIX resources for the
RDMA driver yet.
Fixes: 75720e6323a1 ("bnxt_en: Keep track of reserved IRQs.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the size of the receive buffer for a socket is close to 2^31 when
computing if we have enough space in the buffer to copy a packet from
the queue to the buffer we might hit an integer overflow.
When an user set net.core.rmem_default to a value close to 2^31 UDP
packets are dropped because of this overflow. This can be visible, for
instance, with failure to resolve hostnames.
This can be fixed by casting sk_rcvbuf (which is an int) to unsigned
int, similarly to how it is done in TCP.
Signed-off-by: Antonio Messina <amessina@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>From commit 50895b9de1d3 ("tcp: highest_sack fix"), the logic about
setting tp->highest_sack to the head of the send queue was removed.
Of course the logic is error prone, but it is logical. Before we
remove the pointer to the highest sack skb and use the seq instead,
we need to set tp->highest_sack to NULL when there is no skb after
the last sack, and then replace NULL with the real skb when new skb
inserted into the rtx queue, because the NULL means the highest sack
seq is tp->snd_nxt. If tp->highest_sack is NULL and new data sent,
the next ACK with sack option will increase tp->reordering unexpectedly.
This patch sets tp->highest_sack to the tail of the rtx queue if
it's NULL and new data is sent. The patch keeps the rule that the
highest_sack can only be maintained by sack processing, except for
this only case.
Fixes: 50895b9de1d3 ("tcp: highest_sack fix") Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa2464 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7fda ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u Analyzed-by: Stephen Johnston <sjohnsto@redhat.com> Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com> Signed-off-by: Vladis Dronov <vdronov@redhat.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for
the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate
can be adjusted at runtime.
So far we have been running MPLL2 with ~250MHz (and the internal
m250_div with value 1), which worked enough that we could transfer data
with an TX delay of 4ns. Unfortunately there is high packet loss with
an RGMII PHY when transferring data (receiving data works fine though).
Odroid-C1's u-boot is running with a TX delay of only 2ns as well as
the internal m250_div set to 2 - no lost (TX) packets can be observed
with that setting in u-boot.
Manual testing has shown that the TX packet loss goes away when using
the following settings in Linux (the vendor kernel uses the same
settings):
- MPLL2 clock set to ~500MHz
- m250_div set to 2
- TX delay set to 2ns on the MAC side
Update the m250_div divider settings to only accept dividers greater or
equal 2 to fix the TX delay generated by the MAC.
iperf3 results before the change:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender
[ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver
iperf3 results after the change (including an updated TX delay of 2ns):
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver
Fixes: 4f6a71b84e1afd ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If fq_classify() recycles a struct fq_flow because
a socket structure has been reallocated, we do not
set sk->sk_pacing_status immediately, but later if the
flow becomes detached.
This means that any flow requiring pacing (BBR, or SO_MAX_PACING_RATE)
might fallback to TCP internal pacing, which requires a per-socket
high resolution timer, and therefore more cpu cycles.
Fixes: 218af599fa63 ("tcp: internal implementation for pacing") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert "net/sched: cls_u32: fix refcount leak in the error path of
u32_change()", and fix the u32 refcount leak in a more generic way that
preserves the semantic of rule dumping.
On tc filters that don't support lockless insertion/removal, there is no
need to guard against concurrent insertion when a removal is in progress.
Therefore, for most of them we can avoid a full walk() when deleting, and
just decrease the refcount, like it was done on older Linux kernels.
This fixes situations where walk() was wrongly detecting a non-empty
filter, like it happened with cls_u32 in the error path of change(), thus
leading to failures in the following tdc selftests:
6aa7: (filter, u32) Add/Replace u32 with source match and invalid indev
6658: (filter, u32) Add/Replace u32 with custom hash table and invalid handle
74c2: (filter, u32) Add/Replace u32 filter with invalid hash table id
On cls_flower, and on (future) lockless filters, this check is necessary:
move all the check_empty() logic in a callback so that each filter
can have its own implementation. For cls_flower, it's sufficient to check
if no IDRs have been allocated.
Changes since v1:
- document the need for delete_empty() when TCF_PROTO_OPS_DOIT_UNLOCKED
is used, thanks to Vlad Buslov
- implement delete_empty() without doing fl_walk(), thanks to Vlad Buslov
- squash revert and new fix in a single patch, to be nice with bisect
tests that run tdc on u32 filter, thanks to Dave Miller
Fixes: 275c44aa194b ("net/sched: cls_u32: fix refcount leak in the error path of u32_change()") Fixes: 6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty") Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com> Suggested-by: Vlad Buslov <vladbu@mellanox.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Vlad Buslov <vladbu@mellanox.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no skb_pull performed when a mirred action is set at egress of a
mac device, with a target device/action that expects skb->data to point
at the network header.
As a result, either the target device is errornously given an skb with
data pointing to the mac (egress case), or the net stack receives the
skb with data pointing to the mac (ingress case).
E.g:
# tc qdisc add dev eth9 root handle 1: prio
# tc filter add dev eth9 parent 1: prio 9 protocol ip handle 9 basic \
action mirred egress redirect dev tun0
(tun0 is a tun device. result: tun0 errornously gets the eth header
instead of the iph)
Revise the push/pull logic of tcf_mirred_act() to not rely on the
skb_at_tc_ingress() vs tcf_mirred_act_wants_ingress() comparison, as it
does not cover all "pull" cases.
Instead, calculate whether the required action on the target device
requires the data to point at the network header, and compare this to
whether skb->data points to network header - and make the push/pull
adjustments as necessary.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Shmulik Ladkani <sladkani@proofpoint.com> Tested-by: Jamal Hadi Salim <jhs@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The suspend/resume code for AQR107 works on AQR105 too.
This patch fixes issues with the partner not seeing the link down
when the interface using AQR105 is brought down.
Fixes: bee8259dd31f ("net: phy: add driver for aquantia phy") Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The burning process requires to perform internal allocations of large
chunks of memory. This memory doesn't need to be contiguous and can be
safely allocated by vzalloc() instead of kzalloc(). This patch changes
such allocation to avoid possible out-of-memory failure.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process") Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Tested-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IP fragment is specified through user-defined field as the first
bit of the first user-defined word. We were previously trying to extract
it from the user-defined mask which could not possibly work. The ip_frag
is also supposed to be a boolean, if we do not cast it as such, we risk
overwriting the next fields in CFP_DATA(6) which would render the rule
inoperative.
Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
syzbot (via KASAN) reports a use-after-free in the error path of
xlog_alloc_log(). Specifically, the iclog freeing loop doesn't
handle the case of a fully initialized ->l_iclog linked list.
Instead, it assumes that the list is partially constructed and NULL
terminated.
This bug manifested because there was no possible error scenario
after iclog list setup when the original code was added. Subsequent
code and associated error conditions were added some time later,
while the original error handling code was never updated. Fix up the
error loop to terminate either on a NULL iclog or reaching the end
of the list.
Reported-by: syzbot+c732f8644185de340492@syzkaller.appspotmail.com Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we've done with VFS, string operations, etc, reject usercopy sizes
larger than INT_MAX, which would be nice to have for catching bugs
related to size calculation overflows[1].
This adds 10 bytes to x86_64 defconfig text and 1980 bytes to the data
section:
syzbot is reporting that use of SOCKET_I()->sk from open() can result in
use after free problem [1], for socket's inode is still reachable via
/proc/pid/fd/n despite destruction of SOCKET_I()->sk already completed.
At first I thought that this race condition applies to only open/getattr
permission checks. But James Morris has pointed out that there are more
permission checks where this race condition applies to. Thus, get rid of
tomoyo_get_socket_name() instead of conditionally bypassing permission
checks on sockets. As a side effect of this patch,
"socket:[family=\$:type=\$:protocol=\$]" in the policy files has to be
rewritten to "socket:[\$]".
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 24652 Comm: syz-executor.3 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
[ tglx: Added comments ]
Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20191106174804.74723-1-edumazet@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This code reads two global variables without protection
of a lock. We need READ_ONCE()/WRITE_ONCE() pairs to
avoid load/store-tearing and better document the intent.
KCSAN reported :
BUG: KCSAN: data-race in icmp_global_allow / icmp_global_allow
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 11183 Comm: syz-executor.2 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 4cdf507d5452 ("icmp: add a global rate limitation") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb_peek_tail() can be used without protection of a lock,
as spotted by KCSAN [1]
In order to avoid load-stearing, add a READ_ONCE()
Note that the corresponding WRITE_ONCE() are already there.
[1]
BUG: KCSAN: data-race in sk_wait_data / skb_queue_tail
read to 0xffff8880b36a4118 of 8 bytes by task 20426 on cpu 1:
skb_peek_tail include/linux/skbuff.h:1784 [inline]
sk_wait_data+0x15b/0x250 net/core/sock.c:2477
kcm_wait_data+0x112/0x1f0 net/kcm/kcmsock.c:1103
kcm_recvmsg+0xac/0x320 net/kcm/kcmsock.c:1130
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
write to 0xffff8880b36a4118 of 8 bytes by task 451 on cpu 0:
__skb_insert include/linux/skbuff.h:1852 [inline]
__skb_queue_before include/linux/skbuff.h:1958 [inline]
__skb_queue_tail include/linux/skbuff.h:1991 [inline]
skb_queue_tail+0x7e/0xc0 net/core/skbuff.c:3145
kcm_queue_rcv_skb+0x202/0x310 net/kcm/kcmsock.c:206
kcm_rcv_strparser+0x74/0x4b0 net/kcm/kcmsock.c:370
__strp_recv+0x348/0xf50 net/strparser/strparser.c:309
strp_recv+0x84/0xa0 net/strparser/strparser.c:343
tcp_read_sock+0x174/0x5c0 net/ipv4/tcp.c:1639
strp_read_sock+0xd4/0x140 net/strparser/strparser.c:366
do_strp_work net/strparser/strparser.c:414 [inline]
strp_work+0x9a/0xe0 net/strparser/strparser.c:423
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 451 Comm: kworker/u4:3 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: kstrp strp_work
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
write to 0xffff888121fb2ed0 of 4 bytes by interrupt on cpu 1:
inet_putpeer+0x37/0xa0 net/ipv4/inetpeer.c:240
ip4_frag_free+0x3d/0x50 net/ipv4/ip_fragment.c:102
inet_frag_destroy_rcu+0x58/0x80 net/ipv4/inet_fragment.c:228
__rcu_reclaim kernel/rcu/rcu.h:222 [inline]
rcu_do_batch+0x256/0x5b0 kernel/rcu/tree.c:2157
rcu_core+0x369/0x4d0 kernel/rcu/tree.c:2377
rcu_core_si+0x12/0x20 kernel/rcu/tree.c:2386
__do_softirq+0x115/0x33f kernel/softirq.c:292
run_ksoftirqd+0x46/0x60 kernel/softirq.c:603
smpboot_thread_fn+0x37d/0x4a0 kernel/smpboot.c:165
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 16 Comm: ksoftirqd/1 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 4b9d9be839fd ("inetpeer: remove unused list") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FASTOPEN setsockopt() or sendmsg() may switch the SMC socket to fallback
mode. Once fallback mode is active, the native TCP socket functions are
called. Nevertheless there is a small race window, when FASTOPEN
setsockopt/sendmsg runs in parallel to a connect(), and switch the
socket into fallback mode before connect() takes the sock lock.
Make sure the SMC-specific connect setup is omitted in this case.
This way a syzbot-reported refcount problem is fixed, triggered by
different threads running non-blocking connect() and FASTOPEN_KEY
setsockopt.
The KUAP implementation adds calls in clear_user() to enable and
disable access to userspace memory. However, it doesn't add these to
__clear_user(), which is used in the ptrace regset code.
As there's only one direct user of __clear_user() (the regset code),
and the time taken to set the AMR for KUAP purposes is going to
dominate the cost of a quick access_ok(), there's not much point
having a separate path.
Rename __clear_user() to __arch_clear_user(), and make __clear_user()
just call clear_user().
Reported-by: syzbot+f25ecf4b2982d8c7a640@syzkaller-ppc64.appspotmail.com Reported-by: Daniel Axtens <dja@axtens.net> Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Fixes: de78a9c42a79 ("powerpc: Add a framework for Kernel Userspace Access Protection") Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
[mpe: Use __arch_clear_user() for the asm version like arm64 & nds32] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191209132221.15328-1-ajd@linux.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: vmalloc-out-of-bounds in size_entry_mwt net/bridge/netfilter/ebtables.c:2063 [inline]
BUG: KASAN: vmalloc-out-of-bounds in compat_copy_entries+0x128b/0x1380 net/bridge/netfilter/ebtables.c:2155
Read of size 4 at addr ffffc900004461f4 by task syz-executor267/7937
Because padding isn't considered during computation of ->buf_user_offset,
"total" is decremented by fewer bytes than it should.
Therefore, the first part of
if (*total < sizeof(*entry) || entry->next_offset < sizeof(*entry))
will pass, -- it should not have. This causes oob access:
entry->next_offset is past the vmalloced size.
Reject padding and check that computed user offset (sum of ebt_entry
structure plus all individual matches/watchers/targets) is same
value that userspace gave us as the offset of the next entry.
Both that commit and commit 809805a820c6445f7a701ded24fdc6bbc841d1e4
attempted to fix the same bug (dead assignments to the local variable
cfg), but they did so in incompatible ways. When they were both merged,
independently of each other, the combination actually caused the bug to
reappear, leading to a firmware crash on boot for some cards.
The fix on 951c6db954a1 fixed the issued reported there but introduced
another. When the allocation fails within sctp_stream_init() it is
okay/necessary to free the genradix. But it is also called when adding
new streams, from sctp_send_add_streams() and
sctp_process_strreset_addstrm_in() and in those situations it cannot
just free the genradix because by then it is a fully operational
association.
The fix here then is to only free the genradix in sctp_stream_init()
and on those other call sites move on with what it already had and let
the subsequent error handling to handle it.
Tested with the reproducers from this report and the previous one,
with lksctp-tools and sctp-tests.
Reported-by: syzbot+9a1bc632e78a1a98488b@syzkaller.appspotmail.com Fixes: 951c6db954a1 ("sctp: fix memleak on err handling of stream initialization") Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A while ago Andy noticed
(http://lkml.kernel.org/r/CALCETrWY+5ynDct7eU_nDUqx=okQvjm=Y5wJvA4ahBja=CQXGw@mail.gmail.com)
that UFFD_FEATURE_EVENT_FORK used by an unprivileged user may have
security implications.
As the first step of the solution the following patch limits the availably
of UFFD_FEATURE_EVENT_FORK only for those having CAP_SYS_PTRACE.
The usage of CAP_SYS_PTRACE ensures compatibility with CRIU.
Yet, if there are other users of non-cooperative userfaultfd that run
without CAP_SYS_PTRACE, they would be broken :(
Current implementation of UFFD_FEATURE_EVENT_FORK modifies the file
descriptor table from the read() implementation of uffd, which may have
security implications for unprivileged use of the userfaultfd.
Limit availability of UFFD_FEATURE_EVENT_FORK only for callers that have
CAP_SYS_PTRACE.
Link: http://lkml.kernel.org/r/1572967777-8812-2-git-send-email-rppt@linux.ibm.com Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Reviewed-by: Andrea Arcangeli <aarcange@redhat.com> Cc: Daniel Colascione <dancol@google.com> Cc: Jann Horn <jannh@google.com> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Nick Kralevich <nnk@google.com> Cc: Nosh Minwalla <nosh@google.com> Cc: Pavel Emelyanov <ovzxemul@gmail.com> Cc: Tim Murray <timmurray@google.com> Cc: Aleksa Sarai <cyphar@cyphar.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the drop_caches proc file and sysctl read back the last value
written, suggesting this is somehow a stateful setting instead of a
one-time command. Make it write-only, like e.g. compact_memory.
While mitigating a VM problem at scale in our fleet, there was confusion
about whether writing to this file will permanently switch the kernel into
a non-caching mode. This influences the decision making in a tense
situation, where tens of people are trying to fix tens of thousands of
affected machines: Do we need a rollback strategy? What are the
performance implications of operating in a non-caching state for several
days? It also caused confusion when the kernel team said we may need to
write the file several times to make sure it's effective ("But it already
reads back 3?").
Link: http://lkml.kernel.org/r/20191031221602.9375-1-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Chris Down <chris@chrisdown.name> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: David Hildenbrand <david@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is assumed that the hugetlbfs_vfsmount[] array will contain either a
valid vfsmount pointer or NULL for each hstate after initialization.
Changes made while converting to use fs_context broke this assumption.
While fixing the hugetlbfs_vfsmount issue, it was discovered that
init_hugetlbfs_fs never did correctly clean up when encountering a vfs
mount error.
It was found during code inspection. A small memory allocation failure
would be the most likely cause of taking a error path with the bug.
This is unlikely to happen as this is early init code.
Link: http://lkml.kernel.org/r/94b6244d-2c24-e269-b12c-e3ba694b242d@oracle.com Reported-by: Chengguang Xu <cgxu519@mykernel.net> Fixes: 32021982a324 ("hugetlbfs: Convert to fs_context") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: David Howells <dhowells@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Each SBDT is located at a 4KB page and contains 512 entries.
Each entry of a SDBT points to a SDB, a 4KB page containing
sampled data. The last entry is a link to another SDBT page.
When an event is created the function sequence executed is:
Both functions realloc_sampling_buffers() and
alloc_sample_data_block() allocate pages and the allocation
can fail. This is handled correctly and all allocated
pages are freed and error -ENOMEM is returned to the
top calling function. Finally the event is not created.
Once the event has been created, the amount of initially
allocated SDBT and SDB can be too low. This is detected
during measurement interrupt handling, where the amount
of lost samples is calculated. If the number of lost samples
is too high considering sampling frequency and already allocated
SBDs, the number of SDBs is enlarged during the next execution
of cpumsf_pmu_enable().
are called to allocate more pages. Page allocation may fail
and the returned error is ignored. A SDBT and SDB setup
already exists.
However the modified SDBTs and SDBs might end up in a situation
where the first entry of an SDBT does not point to an SDB,
but another SDBT, basicly an SBDT without payload.
This can not be handled by the interrupt handler, where an SDBT
must have at least one entry pointing to an SBD.
Add a check to avoid SDBTs with out payload (SDBs) when enlarging
the buffer setup.
Currently unwinder unconditionally returns %r14 from the first frame
pointed by %r15 from pt_regs. A task could be interrupted when a function
already allocated this frame (if it needs it) for its callees or to
store local variables. In that case this frame would contain random
values from stack or values stored there by a callee. As we are only
interested in %r14 to get potential return address, skip bogus return
addresses which doesn't belong to kernel text.
This helps to avoid duplicating filtering logic in unwider users, most
of which use unwind_get_return_address() and would choke on bogus 0
address returned by it otherwise.
This patch introduces support for a new architectured reply
code 0x8B indicating that a hypervisor layer (if any) has
rejected an ap message.
Linux may run as a guest on top of a hypervisor like zVM
or KVM. So the crypto hardware seen by the ap bus may be
restricted by the hypervisor for example only a subset like
only clear key crypto requests may be supported. Other
requests will be filtered out - rejected by the hypervisor.
The new reply code 0x8B will appear in such cases and needs
to get recognized by the ap bus and zcrypt device driver zoo.
To avoid breaking the build on arches where this is not wired up, at
least all the other features should be made available and when using
this specific routine, the "unknown" should point the user/developer to
the need to wire this up on this particular hardware architecture.
Detected in a container mipsel debian cross build environment, where it
shows up as:
In file included from /usr/mipsel-linux-gnu/include/stdio.h:867,
from /git/linux/tools/perf/lib/include/perf/cpumap.h:6,
from util/session.c:13:
In function 'printf',
inlined from 'regs_dump__printf' at util/session.c:1103:3,
inlined from 'regs__printf' at util/session.c:1131:2:
/usr/mipsel-linux-gnu/include/bits/stdio2.h:107:10: error: '%-5s' directive argument is null [-Werror=format-overflow=]
107 | return __printf_chk (__USE_FORTIFY_LEVEL - 1, __fmt, __va_arg_pack ());
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from /usr/mips64-linux-gnuabi64/include/stdio.h:867,
from /git/linux/tools/perf/lib/include/perf/cpumap.h:6,
from util/session.c:13:
In function 'printf',
inlined from 'regs_dump__printf' at util/session.c:1103:3,
inlined from 'regs__printf' at util/session.c:1131:2,
inlined from 'regs_user__printf' at util/session.c:1139:3,
inlined from 'dump_sample' at util/session.c:1246:3,
inlined from 'machines__deliver_event' at util/session.c:1421:3:
/usr/mips64-linux-gnuabi64/include/bits/stdio2.h:107:10: error: '%-5s' directive argument is null [-Werror=format-overflow=]
107 | return __printf_chk (__USE_FORTIFY_LEVEL - 1, __fmt, __va_arg_pack ());
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function 'printf',
inlined from 'regs_dump__printf' at util/session.c:1103:3,
inlined from 'regs__printf' at util/session.c:1131:2,
inlined from 'regs_intr__printf' at util/session.c:1147:3,
inlined from 'dump_sample' at util/session.c:1249:3,
inlined from 'machines__deliver_event' at util/session.c:1421:3:
/usr/mips64-linux-gnuabi64/include/bits/stdio2.h:107:10: error: '%-5s' directive argument is null [-Werror=format-overflow=]
107 | return __printf_chk (__USE_FORTIFY_LEVEL - 1, __fmt, __va_arg_pack ());
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
brstackinsn must be allowed to be set by the user when AUX area data has
been captured because, in that case, the branch stack might be
synthesized on the fly. This fixes the following error:
Before:
$ perf record -e '{intel_pt//,cpu/mem_inst_retired.all_loads,aux-sample-size=8192/pp}:u' grep -rqs jhgjhg /boot
[ perf record: Woken up 19 times to write data ]
[ perf record: Captured and wrote 2.274 MB perf.data ]
$ perf script -F +brstackinsn --xed --itrace=i1usl100 | head
Display of branch stack assembler requested, but non all-branch filter set
Hint: run 'perf record -b ...'
After:
$ perf record -e '{intel_pt//,cpu/mem_inst_retired.all_loads,aux-sample-size=8192/pp}:u' grep -rqs jhgjhg /boot
[ perf record: Woken up 19 times to write data ]
[ perf record: Captured and wrote 2.274 MB perf.data ]
$ perf script -F +brstackinsn --xed --itrace=i1usl100 | head
grep 13759 [002] 8091.310257: 1862 instructions:uH: 5641d58069eb bmexec+0x86b (/bin/grep)
bmexec+2485: 00005641d5806b35 jnz 0x5641d5806bd0 # MISPRED 00005641d5806bd0 movzxb (%r13,%rdx,1), %eax 00005641d5806bd6 add %rdi, %rax 00005641d5806bd9 movzxb -0x1(%rax), %edx 00005641d5806bdd cmp %rax, %r14 00005641d5806be0 jnb 0x5641d58069c0 # MISPRED
mismatch of LBR data and executable 00005641d58069c0 movzxb (%r13,%rdx,1), %edi
Fixes: 48d02a1d5c13 ("perf script: Add 'brstackinsn' for branch stacks") Reported-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Link: http://lore.kernel.org/lkml/20191127095322.15417-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To fix these build errors on a debian mipsel cross build environment:
builtin-diff.c: In function 'block_cycles_diff_cmp':
builtin-diff.c:550:6: error: absolute value function 'labs' given an argument of type 's64' {aka 'long long int'} but has parameter of type 'long int' which may cause truncation of value [-Werror=absolute-value]
550 | l = labs(left->diff.cycles);
| ^~~~
builtin-diff.c:551:6: error: absolute value function 'labs' given an argument of type 's64' {aka 'long long int'} but has parameter of type 'long int' which may cause truncation of value [-Werror=absolute-value]
551 | r = labs(right->diff.cycles);
| ^~~~
Fixes: 99150a1faab2 ("perf diff: Use hists to manage basic blocks per symbol") Cc: Jin Yao <yao.jin@linux.intel.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-pn7szy5uw384ntjgk6zckh6a@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch moves the final part of the cifsFileInfo_put() logic where we
need a write lock on lock_sem to be processed in a separate thread that
holds no other locks.
This is to prevent deadlocks like the one below:
Reported-by: Frank Sorenson <sorenson@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In attach_node_and_children memory is allocated for full_name via
kasprintf. If the condition of the 1st if is not met the function
returns early without freeing the memory. Add a kfree() to fix that.
This has been detected with kmemleak: Link: https://bugzilla.kernel.org/show_bug.cgi?id=205327
It looks like the leak was introduced by this commit: Fixes: 5babefb7f7ab ("of: unittest: allow base devicetree to have symbol metadata") Signed-off-by: Erhard Furtner <erhard_f@mailbox.org> Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We currently rely on the ring destroy on cleaning things up in case of
failure, but io_allocate_scq_urings() can leave things half initialized
if only parts of it fails.
Be nice and return with either everything setup in success, or return an
error with things nicely cleaned up.
When we get an interrupt from the socket getting readable,
and start reading, there's a possibility for a race. This
depends on the implementation of the device, but e.g. with
qemu's libvhost-user, we can see:
device virtio_uml
---------------------------------------
write header
get interrupt
read header
read body -> returns -EAGAIN
write body
The -EAGAIN return is because the socket is non-blocking,
and then this leads us to abandon this message.
In fact, we've already read the header, so when the get
another signal/interrupt for the body, we again read it
as though it's a new message header, and also abandon it
for the same reason (wrong size etc.)
This essentially breaks things, and if that message was
one that required a response, it leads to a deadlock as
the device is waiting for the response but we'll never
reply.
Fix this by spinning on -EAGAIN as well when we read the
message body. We need to handle -EAGAIN as "no message"
while reading the header, since we share an interrupt.
Note that this situation is highly unlikely to occur in
normal usage, since there will be very few messages and
only in the startup phase. With the inband call feature
this does tend to happen (eventually) though.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure we grab an active reference in cifs superblock while doing
failover to prevent automounts (DFS links) of expiring and then
destroying the superblock pointer.
This patch fixes the following KASAN report:
[ 464.301462] BUG: KASAN: use-after-free in
cifs_reconnect+0x6ab/0x1350
[ 464.303052] Read of size 8 at addr ffff888155e580d0 by task
cifsd/1107
[ 464.367005] Memory state around the buggy address:
[ 464.367787] ffff888155e57f80: fc fc fc fc fc fc fc fc fc fc fc fc
fc fc fc fc
[ 464.368877] ffff888155e58000: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 464.369967] >ffff888155e58080: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 464.371111] ^
[ 464.371775] ffff888155e58100: fc fc fc fc fc fc fc fc fc fc fc fc
fc fc fc fc
[ 464.372893] ffff888155e58180: fc fc fc fc fc fc fc fc fc fc fc fc
fc fc fc fc
[ 464.373983] ==================================================================
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building pseries_defconfig, building vdso32 errors out:
error: unknown target ABI 'elfv1'
This happens because -m32 in clang changes the target to 32-bit,
which does not allow the ABI to be changed.
Commit 4dc831aa8813 ("powerpc: Fix compiling a BE kernel with a
powerpc64le toolchain") added these flags to fix building big endian
kernels with a little endian GCC.
Clang doesn't need -mabi because the target triple controls the
default value. -mlittle-endian and -mbig-endian manipulate the triple
into either powerpc64-* or powerpc64le-*, which properly sets the
default ABI.
Adding a debug print out in the PPC64TargetInfo constructor after line
383 above shows this:
Don't specify -mabi when building with clang to avoid the build error
with -m32 and not change any code generation.
-mcall-aixdesc is not an implemented flag in clang so it can be safely
excluded as well, see commit 238abecde8ad ("powerpc: Don't use gcc
specific options on clang").
pseries_defconfig successfully builds after this patch and
powernv_defconfig and ppc44x_defconfig don't regress.
Reviewed-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[mpe: Trim clang links in change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20191119045712.39633-2-natechancellor@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
build_initial_tok_table() overwrites unused sym_entry to shrink the
table size. Before the entry is overwritten, table[i].sym must be freed
since it is malloc'ed data.
This fixes the 'definitely lost' report from valgrind. I ran valgrind
against x86_64_defconfig of v5.4-rc8 kernel, and here is the summary:
[Before the fix]
LEAK SUMMARY:
definitely lost: 53,184 bytes in 2,874 blocks
[After the fix]
LEAK SUMMARY:
definitely lost: 0 bytes in 0 blocks
find_vma() must be called under the mmap_sem, reorganize this code to
do the vma check after entering the lock.
Further, fix the unlocked use of struct task_struct's mm, instead use
the mm from hmm_mirror which has an active mm_grab. Also the mm_grab
must be converted to a mm_get before acquiring mmap_sem or calling
find_vma().
Fixes: 66c45500bfdc ("drm/amdgpu: use new HMM APIs and helpers") Fixes: 0919195f2b0d ("drm/amdgpu: Enable amdgpu_ttm_tt_get_user_pages in worker threads") Link: https://lore.kernel.org/r/20191112202231.3856-11-jgg@ziepe.ca Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Philip Yang <Philip.Yang@amd.com> Tested-by: Philip Yang <Philip.Yang@amd.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sanity check in macro update_for_len checks to see if len
is less than zero, however, len is a size_t so it can never be
less than zero, so this sanity check is a no-op. Fix this by
making len a ssize_t so the comparison will work and add ulen
that is a size_t copy of len so that the min() macro won't
throw warnings about comparing different types.
Addresses-Coverity: ("Macro compares unsigned to 0") Fixes: f1bd904175e8 ("apparmor: add the base fns() for domain labels") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The crash handler calls hv_synic_cleanup() to shutdown the
Hyper-V synthetic interrupt controller. But if the CPU
that calls hv_synic_cleanup() has a VMbus channel interrupt
assigned to it (which is likely the case in smaller VM sizes),
hv_synic_cleanup() returns an error and the synthetic
interrupt controller isn't shutdown. While the lack of
being shutdown hasn't caused a known problem, it still
should be fixed for highest reliability.
So directly call hv_synic_disable_regs() instead of
hv_synic_cleanup(), which ensures that the synic is always
shutdown.
Signed-off-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible that certain config levels are not available, even
if the max level includes the level. There can be missing levels in
some platforms. So ignore the level when called for information dump
for all levels and fail if specifically ask for the missing level.
Here the changes is to continue reading information about other levels
even if we fail to get information for the current level. But use the
"processed" flag to indicate the failure. When the "processed" flag is
not set, don't dump information about that level.
When commit 75e99bf5ed8f ("gpio: lynxpoint: set default handler to be
handle_bad_irq()") switched default handler to be handle_bad_irq() the
lp_irq_type() function remained untouched. It means that even request_irq()
can't change the handler and we are not able to handle IRQs properly anymore.
Fix it by setting correct handlers in the lp_irq_type() callback.
Fixes: 75e99bf5ed8f ("gpio: lynxpoint: set default handler to be handle_bad_irq()") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20191118180251.31439-1-andriy.shevchenko@linux.intel.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The per-SoC devtype structures can contain their own callbacks that
overwrite mpc8xxx_gpio_devtype_default.
The clear intention is that mpc8xxx_irq_set_type is used in case the SoC
does not specify a more specific callback. But what happens is that if
the SoC doesn't specify one, its .irq_set_type is de-facto NULL, and
this overwrites mpc8xxx_irq_set_type to a no-op. This means that the
following SoCs are affected:
On these boards, the irq_set_type does exactly nothing, and the GPIO
controller keeps its GPICR register in the hardware-default state. On
the LS1028A, that is ACTIVE_BOTH, which means 2 interrupts are raised
even if the IRQ client requests LEVEL_HIGH. Another implication is that
the IRQs are not checked (e.g. level-triggered interrupts are not
rejected, although they are not supported).
Fixes: 82e39b0d8566 ("gpio: mpc8xxx: handle differences between incarnations at a single place") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20191115125551.31061-1-olteanv@gmail.com Tested-by: Michael Walle <michael@walle.cc> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Intel's SoCs follow a naming convention which spells out the SoC name as
two words instead of one word (E.g: Cannon Lake vs Cannonlake). Thus fix
the naming inconsistency across the intel_pmc_core driver, so future
SoCs can follow the naming consistency as below.
Cometlake -> Comet Lake
Tigerlake -> Tiger Lake
Elkhartlake -> Elkhart Lake
Cc: Mario Limonciello <mario.limonciello@dell.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Srinivas Pandruvada <srinivas.pandruvada@intel.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Kan Liang <kan.liang@intel.com> Cc: David E. Box <david.e.box@intel.com> Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com> Cc: Tony Luck <tony.luck@intel.com> Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Gayatri Kammela <gayatri.kammela@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reduce context close time by skipping the VA block free list update in
order to avoid hard reset with open contexts.
Reset with open contexts can potentially lead to a kernel crash as the
generic pool of the MMU hops is destroyed while it is not empty because
some unmap operations are not done.
The commit affect mainly when running on simulator.
The root cause for this issue is there is a potential infinite loop
in f2fs_drop_inmem_pages_all() for the case where gc_failure is true
and when there an inode whose i_gc_failures[GC_FAILURE_ATOMIC] is
not set. Fix this by keeping track of the total atomic files
currently opened and using that to exit from this condition.
The iSCSI target driver is the only target driver that does not wait for
ongoing commands to finish before freeing a session. Make the iSCSI target
driver wait for ongoing commands to finish before freeing a session. This
patch fixes the following KASAN complaint:
BUG: KASAN: use-after-free in __lock_acquire+0xb1a/0x2710
Read of size 8 at addr ffff8881154eca70 by task kworker/0:2/247
Memory state around the buggy address: ffff8881154ec900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881154ec980: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
>ffff8881154eca00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881154eca80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881154ecb00: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
Cc: Mike Christie <mchristi@redhat.com> Link: https://lore.kernel.org/r/20191113220508.198257-3-bvanassche@acm.org Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a faulty initiator fails to bind the socket to the iSCSI connection
before emitting a command, for instance, a subsequent send_pdu, it will
crash the kernel due to a null pointer dereference in sock_sendmsg(), as
shown in the log below. This patch makes sure the bind succeeded before
trying to use the socket.
projects / linux-stable / log