The ADC in the JZ4740 can work either in high-precision mode with a 2.5V
range, or in low-precision mode with a 7.5V range. The code in place in
this driver will select the proper scale according to the maximum
voltage of the battery.
The JZ4770 however only has one mode, with a 6.6V range. If only one
scale is available, there's no need to change it (and nothing to change
it to), and trying to do so will fail with -EINVAL.
Fixes: fb24ccfbe1e0 ("power: supply: add Ingenic JZ47xx battery driver.") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Acked-by: Artur Rojek <contact@artur-rojek.eu> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 786b2384bf1c ("um: Enable CONFIG_CONSTRUCTORS").
There are two issues with this commit, uncovered by Anton in tests
on some (Debian) systems:
1) I completely forgot to call any constructors if CONFIG_CONSTRUCTORS
isn't set. Don't recall now if it just wasn't needed on my system, or
if I never tested this case.
2) With that fixed, it works - with CONFIG_CONSTRUCTORS *unset*. If I
set CONFIG_CONSTRUCTORS, it fails again, which isn't totally
unexpected since whatever wanted to run is likely to have to run
before the kernel init etc. that calls the constructors in this case.
Basically, some constructors that gcc emits (libc has?) need to run
very early during init; the failure mode otherwise was that the ptrace
fork test already failed:
----------------------
$ ./linux mem=512M
Core dump limits :
soft - 0
hard - NONE
Checking that ptrace can change system call numbers...check_ptrace : child exited with exitcode 6, while expecting 0; status 0x67f
Aborted
----------------------
Thinking more about this, it's clear that we simply cannot support
CONFIG_CONSTRUCTORS in UML. All the cases we need now (gcov, kasan)
involve not use of the __attribute__((constructor)), but instead
some constructor code/entry generated by gcc. Therefore, we cannot
distinguish between kernel constructors and system constructors.
Thus, revert this commit.
Cc: stable@vger.kernel.org [5.4+] Fixes: 786b2384bf1c ("um: Enable CONFIG_CONSTRUCTORS") Reported-by: Anton Ivanov <anton.ivanov@cambridgegreys.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Anton Ivanov <anton.ivanov@cambridgegreys.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Richard Weinberger <richard@nod.at>
On VHE systems arch.mdcr_el2 is written to mdcr_el2 at vcpu_load time to
set options for self-hosted debug and the performance monitors
extension.
Unfortunately the value of arch.mdcr_el2 is not calculated until
kvm_arm_setup_debug() in the run loop after the vcpu has been loaded.
This means that the initial brief iterations of the run loop use a zero
value of mdcr_el2 - until the vcpu is preempted. This also results in a
delay between changes to vcpu->guest_debug taking effect.
Fix this by writing to mdcr_el2 in kvm_arm_setup_debug() on VHE systems
when a change to arch.mdcr_el2 has been detected.
Fixes: d5a21bcc2995 ("KVM: arm64: Move common VHE/non-VHE trap config in separate functions") Cc: <stable@vger.kernel.org> # 4.17.x- Suggested-by: James Morse <james.morse@arm.com> Acked-by: Will Deacon <will@kernel.org> Reviewed-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Andrew Murray <andrew.murray@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On module unload of pcrypt we must unregister the crypto algorithms
first and then tear down the padata structure. As otherwise the
crypto algorithms are still alive and can be used while the padata
structure is being freed.
In commit 'a1cf573ee95 ("crypto: caam - select DMA address size at runtime")'
CAAM pointer size (caam_ptr_size) is changed from
sizeof(dma_addr_t) to runtime value computed from MCFGR register.
Therefore, do not reset MCFGR[PS].
When the kernel XTS implementation was extended to deal with ciphertext
stealing in commit 8083b1bf8163 ("crypto: xts - add support for ciphertext
stealing"), a check was added to reject inputs that were too short.
However, in the vmx enablement - commit 239668419349 ("crypto: vmx/xts -
use fallback for ciphertext stealing"), that check wasn't added to the
vmx implementation. This disparity leads to errors like the following:
alg: skcipher: p8_aes_xts encryption unexpectedly succeeded on test vector "random: len=0 klen=64"; expected_error=-22, cfg="random: inplace may_sleep use_finup src_divs=[<flush>66.99%@+10, 33.1%@alignmask+1155]"
Return -EINVAL if asked to operate with a cryptlen smaller than the AES
block size. This brings vmx in line with the generic implementation.
Reported-by: Erhard Furtner <erhard_f@mailbox.org> Link: https://bugzilla.kernel.org/show_bug.cgi?id=206049 Fixes: 239668419349 ("crypto: vmx/xts - use fallback for ciphertext stealing") Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[dja: commit message] Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As af_alg_release_parent may be called from BH context (most notably
due to an async request that only completes after socket closure,
or as reported here because of an RCU-delayed sk_destruct call), we
must use bh_lock_sock instead of lock_sock.
The driver would fail to stop the command timer in most error paths,
something which specifically could lead to the timer being freed while
still active on I/O errors during probe.
Fix this by making sure that each function starting the timer also stops
it in all relevant error paths.
Reported-by: syzbot+1d1597a5aa3679c65b9f@syzkaller.appspotmail.com Fixes: b78e91bcfb33 ("rsi: Add new firmware loading method") Cc: stable <stable@vger.kernel.org> # 4.12 Cc: Prameela Rani Garnepudi <prameela.j04cs@gmail.com> Cc: Amitkumar Karwar <amit.karwar@redpinesignals.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The subpacket scanning loop in rxrpc_receive_data() references the
subpacket count in the private data part of the sk_buff in the loop
termination condition. However, when the final subpacket is pasted into
the ring buffer, the function is no longer has a ref on the sk_buff and
should not be looking at sp->* any more. This point is actually marked in
the code when skb is cleared (but sp is not - which is an error).
Fix this by caching sp->nr_subpackets in a local variable and using that
instead.
Also clear 'sp' to catch accesses after that point.
This can show up as an oops in rxrpc_get_skb() if sp->nr_subpackets gets
trashed by the sk_buff getting freed and reused in the meantime.
Fixes: e2de6c404898 ("rxrpc: Use info in skbuff instead of reparsing a jumbo packet") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the size of struct nhmsg size when calculating
how much of a payload to allocate in a new netlink nexthop
notification message.
Without this, we will fail to fill the skbuff at certain nexthop
group sizes.
You can reproduce the failure with the following iproute2 commands:
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link add dummy3 type dummy
ip link add dummy4 type dummy
ip link add dummy5 type dummy
ip link add dummy6 type dummy
ip link add dummy7 type dummy
ip link add dummy8 type dummy
ip link add dummy9 type dummy
ip link add dummy10 type dummy
ip link add dummy11 type dummy
ip link add dummy12 type dummy
ip link add dummy13 type dummy
ip link add dummy14 type dummy
ip link add dummy15 type dummy
ip link add dummy16 type dummy
ip link add dummy17 type dummy
ip link add dummy18 type dummy
ip link add dummy19 type dummy
ip ro add 1.1.1.1/32 dev dummy1
ip ro add 1.1.1.2/32 dev dummy2
ip ro add 1.1.1.3/32 dev dummy3
ip ro add 1.1.1.4/32 dev dummy4
ip ro add 1.1.1.5/32 dev dummy5
ip ro add 1.1.1.6/32 dev dummy6
ip ro add 1.1.1.7/32 dev dummy7
ip ro add 1.1.1.8/32 dev dummy8
ip ro add 1.1.1.9/32 dev dummy9
ip ro add 1.1.1.10/32 dev dummy10
ip ro add 1.1.1.11/32 dev dummy11
ip ro add 1.1.1.12/32 dev dummy12
ip ro add 1.1.1.13/32 dev dummy13
ip ro add 1.1.1.14/32 dev dummy14
ip ro add 1.1.1.15/32 dev dummy15
ip ro add 1.1.1.16/32 dev dummy16
ip ro add 1.1.1.17/32 dev dummy17
ip ro add 1.1.1.18/32 dev dummy18
ip ro add 1.1.1.19/32 dev dummy19
ip next add id 1 via 1.1.1.1 dev dummy1
ip next add id 2 via 1.1.1.2 dev dummy2
ip next add id 3 via 1.1.1.3 dev dummy3
ip next add id 4 via 1.1.1.4 dev dummy4
ip next add id 5 via 1.1.1.5 dev dummy5
ip next add id 6 via 1.1.1.6 dev dummy6
ip next add id 7 via 1.1.1.7 dev dummy7
ip next add id 8 via 1.1.1.8 dev dummy8
ip next add id 9 via 1.1.1.9 dev dummy9
ip next add id 10 via 1.1.1.10 dev dummy10
ip next add id 11 via 1.1.1.11 dev dummy11
ip next add id 12 via 1.1.1.12 dev dummy12
ip next add id 13 via 1.1.1.13 dev dummy13
ip next add id 14 via 1.1.1.14 dev dummy14
ip next add id 15 via 1.1.1.15 dev dummy15
ip next add id 16 via 1.1.1.16 dev dummy16
ip next add id 17 via 1.1.1.17 dev dummy17
ip next add id 18 via 1.1.1.18 dev dummy18
ip next add id 19 via 1.1.1.19 dev dummy19
ip next add id 1111 group 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15/16/17/18/19
ip next del id 1111
Fixes: 430a049190de ("nexthop: Add support for nexthop groups") Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multicast and broadcast packets can be looped from egress to ingress
pre segmentation with dev_loopback_xmit. That function unconditionally
sets ip_summed to CHECKSUM_UNNECESSARY.
udp_rcv_segment segments gso packets in the udp rx path. Segmentation
usually executes on egress, and does not expect packets of this type.
__udp_gso_segment interprets !CHECKSUM_PARTIAL as CHECKSUM_NONE. But
the offsets are not correct for gso_make_checksum.
UDP GSO packets are of type CHECKSUM_PARTIAL, with their uh->check set
to the correct pseudo header checksum. Reset ip_summed to this type.
(CHECKSUM_PARTIAL is allowed on ingress, see comments in skbuff.h)
Reported-by: syzbot <syzkaller@googlegroups.com> Fixes: cf329aa42b66 ("udp: cope with UDP GRO packet misdirection") Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix xdp_result initialization in netsec_process_rx in order to not
increase rx counters if there is no bpf program attached to the xdp hook
and napi_gro_receive returns GRO_DROP
Fixes: ba2b232108d3c ("net: netsec: add XDP support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix possible use-after-free in in netsec_process_rx that can occurs if
the first packet is sent to the normal networking stack and the
following one is dropped by the bpf program attached to the xdp hook.
Fix the issue defining the skb pointer in the 'budget' loop
Fixes: ba2b232108d3c ("net: netsec: add XDP support") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip \
sport 80 0xffff flowid 1:3
tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip \
sport 25 0xffff flowid 1:4
where filters are installed on qdisc 1:0, so we can't merely
search from class 1:1 when creating class 1:3 and class 1:4. We have
to walk through all the child classes of the direct parent qdisc.
Otherwise we would miss filters those need reverse binding.
Fixes: 07d79fc7d94e ("net_sched: add reverse binding for tc class") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementations of ops->bind_class() are merely
searching for classid and updating class in the struct tcf_result,
without invoking either of cl_ops->bind_tcf() or
cl_ops->unbind_tcf(). This breaks the design of them as qdisc's
like cbq use them to count filters too. This is why syzbot triggered
the warning in cbq_destroy_class().
In order to fix this, we have to call cl_ops->bind_tcf() and
cl_ops->unbind_tcf() like the filter binding path. This patch does
so by refactoring out two helper functions __tcf_bind_filter()
and __tcf_unbind_filter(), which are lockless and accept a Qdisc
pointer, then teaching each implementation to call them correctly.
Note, we merely pass the Qdisc pointer as an opaque pointer to
each filter, they only need to pass it down to the helper
functions without understanding it at all.
Fixes: 07d79fc7d94e ("net_sched: add reverse binding for tc class") Reported-and-tested-by: syzbot+0a0596220218fcb603a8@syzkaller.appspotmail.com Reported-and-tested-by: syzbot+63bdb6006961d8c917c6@syzkaller.appspotmail.com Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+03c4738ed29d5d366ddf@syzkaller.appspotmail.com Cc: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently XDP Support was added to the mvneta driver
for software buffer management only.
It is still possible to attach an XDP program if
hardware buffer management is used.
It is not doing anything at that point.
The patch disallows attaching XDP programs to mvneta
if hardware buffer management is used.
I am sorry about that. It is my first submission and I am having
some troubles with the format of my emails.
v4 -> v5:
- Remove extra tabs
v3 -> v4:
- Please ignore v3 I accidentally submitted
my other patch with git-send-mail and v4 is correct
v2 -> v3:
- My mailserver corrupted the patch
resubmission with git-send-email
v1 -> v2:
- Fixing the patches indentation
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 71bb244ba2fd ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets") Cc: stable <stable@vger.kernel.org> # 3.4 Cc: Arend van Spriel <arend@broadcom.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Fixes: 9150c3adbf24 ("CIFS: Close open handle after interrupted close") Cc: Stable <stable@vger.kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two places where we need to adjust down the max response size for
ioctl when it is used together with compounding.
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The task which created the MID may be gone by the time cifsd attempts to
call the callbacks on MIDs from cifs_reconnect().
This leads to a use-after-free of the task struct in cifs_wake_up_task:
==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x31a0/0x3270
Read of size 8 at addr ffff8880103e3a68 by task cifsd/630
This can be reliably reproduced by adding the below delay to
cifs_reconnect(), running find(1) on the mount, restarting the samba
server while find is running, and killing find during the delay:
Fix this by holding a reference to the task struct until the MID is
freed.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Signed-off-by: Steve French <stfrench@microsoft.com> CC: Stable <stable@vger.kernel.org> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chelsio crypto driver is casting 'struct crypto_aead' directly to
'struct crypto_tfm', which is incorrect because the crypto_tfm isn't the
first field of 'struct crypto_aead'. Consequently, the calls to
crypto_tfm_set_flags() are modifying some other field in the struct.
Also, the driver is setting CRYPTO_TFM_RES_BAD_KEY_LEN in
->setauthsize(), not just in ->setkey(). This is incorrect since this
flag is for bad key lengths, not for bad authentication tag lengths.
Fix these bugs by removing the broken crypto_tfm_set_flags() calls from
->setauthsize() and by fixing them in ->setkey().
Fixes: 324429d74127 ("chcr: Support for Chelsio's Crypto Hardware") Cc: <stable@vger.kernel.org> # v4.9+ Cc: Atul Gupta <atul.gupta@chelsio.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 57ea974fb871 ("driver core: Rewrite test_async_driver_probe
to cover serialization and NUMA affinity"), running the test with NUMA
disabled results in warning messages similar to the following.
test_async_driver test_async_driver.12: NUMA node mismatch -1 != 0
If CONFIG_NUMA=n, dev_to_node(dev) returns -1, and numa_node_id()
returns 0. Both are widely used, so it appears risky to change return
values. Augment the check with IS_ENABLED(CONFIG_NUMA) instead
to fix the problem.
Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com> Fixes: 57ea974fb871 ("driver core: Rewrite test_async_driver_probe to cover serialization and NUMA affinity") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: stable <stable@vger.kernel.org> Acked-by: Alexander Duyck <alexander.h.duyck@linux.intel.com> Link: https://lore.kernel.org/r/20191127202453.28087-1-linux@roeck-us.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 41c128cb25ce ("iio: st_gyro: Add lsm9ds0-gyro support")
assumes that gyro in LSM9DS0 is the same as others with 0xd4 WAI ID,
but datasheet tells slight different story, i.e. the first scale factor
for the chip is 245 dps, and not 250 dps.
Correct this by introducing a separate settings for LSM9DS0.
Fixes: 41c128cb25ce ("iio: st_gyro: Add lsm9ds0-gyro support")
Depends-on: 45a4e4220bf4 ("iio: gyro: st_gyro: fix L3GD20H support") Cc: Leonard Crestez <leonard.crestez@nxp.com> Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 43e23b6c0b01 ("debugfs: log errors when something goes wrong")
debugfs logs attempts to create existing files.
However binder attempts to create multiple debugfs files with
the same name when a single PID has multiple contexts, this leads
to log spamming during an Android boot (17 such messages during
boot on my system).
Fix this by checking if we already know the PID and only create
the debugfs entry for the first context per PID.
The match data does not have to be a struct device pointer, and indeed
very often is not. Attempt to treat it as such easily results in a
crash.
For the components that are not registered, we don't know which device
is missing. Once it it is there, we can use the struct component to get
the device and whether it's bound or not.
Change the return type to int and return -EPERM when lockdown is enabled
to remove the warning above. Also rename debugfs_is_locked_down to
debugfs_locked_down to make it sound less like it returns a boolean.
Fixes: 5496197f9b08 ("debugfs: Restrict debugfs when the kernel is locked down") Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: stable <stable@vger.kernel.org> Acked-by: James Morris <jamorris@linux.microsoft.com> Link: https://lore.kernel.org/r/20191207161603.35907-1-eric.snowberg@oracle.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main irq handler function starts by first masking disabled
interrupts in the status register values to ensure to only handle
enabled interrupts. This is important as when the RX path in the
hardware is disabled reading the RX fifo results in an external abort.
This checking must be done under the port lock, otherwise the following
can happen:
CPU1 | CPU2
|
irq triggers as there are chars |
in the RX fifo |
| grab port lock
imx_uart_int finds RRDY enabled |
and calls imx_uart_rxint which |
has to wait for port lock |
| disable RX (e.g. because we're
| using RS485 with !RX_DURING_TX)
|
| release port lock
read from RX fifo with RX |
disabled => exception |
So take the port lock only once in imx_uart_int() instead of in the
functions called from there.
Unbinding the bcm2835aux UART driver raises the following error if the
maximum number of 8250 UARTs is set to 1 (via the 8250.nr_uarts module
parameter or CONFIG_SERIAL_8250_RUNTIME_UARTS):
That's because bcm2835aux_serial_probe() retrieves UART line number 1
from the devicetree and stores it in data->uart.port.line, while
serial8250_register_8250_port() instead uses UART line number 0,
which is stored in data->line.
On driver unbind, bcm2835aux_serial_remove() uses data->uart.port.line,
which contains the wrong number. Fix it.
The issue does not occur if the maximum number of 8250 UARTs is >= 2.
Fixes: bdc5f3009580 ("serial: bcm2835: add driver for bcm2835-aux-uart") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.6+ Cc: Martin Sperl <kernel@martin.sperl.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/912ccf553c5258135c6d7e8f404a101ef320f0f4.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver reporting IEEE80211_TX_STAT_ACK is not being handled
correctly. The driver should only report on TSR_TMO flag is not
set indicating no transmission errors and when not IEEE80211_TX_CTL_NO_ACK
is being requested.
Currently when the call to prism2sta_ifst fails a netdev_err error
is reported, error return variable result is set to -1 but the
function always returns 0 for success. Fix this by returning
the error value in variable result rather than 0.
Addresses-Coverity: ("Unused value") Fixes: 00b3ed168508 ("Staging: add wlan-ng prism2 usb driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200114181604.390235-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the length of the socket buffer is 0xFFFFFFFF (max size for an
unsigned int), then payload_len becomes 0xFFFFFFF1 after subtracting 14
(ETH_HLEN). Then, mdp_len is set to payload_len + 16 (MDP_HDR_LEN)
which overflows and results in a value of 2. These values for
payload_len and mdp_len will pass current buffer size checks.
This patch checks if derived from skb->len sum may overflow.
The check is based on the following idea:
For any `unsigned V1, V2` and derived `unsigned SUM = V1 + V2`,
`V1 + V2` overflows iif `SUM < V1`.
commit 8f6244055bd3 ("usb: typec: fusb302: Always provide fwnode for the
port") didn't convert this value from mW to uW when migrating to a new
specification format like it should have.
Fixes: 8f6244055bd3 ("usb: typec: fusb302: Always provide fwnode for the port") Cc: stable@vger.kernel.org Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/0da564559af75ec829c6c7e3aa4024f857c91bee.1579529334.git.tommyhebb@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c912bff46cc ("usb: typec: wcove: Provide fwnode for the port")
didn't convert this value from mW to uW when migrating to a new
specification format like it should have.
Fixes: 4c912bff46cc ("usb: typec: wcove: Provide fwnode for the port") Cc: stable@vger.kernel.org Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/d8be32512efd31995ad7d65b27df9d443131b07c.1579529334.git.tommyhebb@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VBUS should be turned off when leaving the host mode.
Set GCTL_PRTCAP to device mode in teardown to de-assert DRVVBUS pin to
turn off VBUS power.
Fixes: 5f94adfeed97 ("usb: dwc3: core: refactor mode initialization to its own function") Cc: stable@vger.kernel.org Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f4a4cbb2047e ("USB: ir-usb: reimplement using generic framework")
switched to using the generic write implementation which may combine
multiple write requests into larger transfers. This can break the IrLAP
protocol where end-of-frame is determined using the USB short packet
mechanism, for example, if multiple frames are sent in rapid succession.
Commit e0d795e4f36c ("usb: irda: cleanup on ir-usb module") added a USB
IrDA header with common defines, but mistakingly switched to using the
class-descriptor baud-rate bitmask values for the outbound header.
This broke link-speed handling for rates above 9600 baud, but a device
would also be able to operate at the default 9600 baud until a
link-speed request was issued (e.g. using the TCGETS ioctl).
Fixes: e0d795e4f36c ("usb: irda: cleanup on ir-usb module") Cc: stable <stable@vger.kernel.org> # 2.6.27 Cc: Felipe Balbi <balbi@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing endpoint sanity check to avoid dereferencing a NULL-pointer
on open() in case a device lacks a bulk-out endpoint.
Note that prior to commit f4a4cbb2047e ("USB: ir-usb: reimplement using
generic framework") the oops would instead happen on open() if the
device lacked a bulk-in endpoint and on write() if it lacked a bulk-out
endpoint.
Set the MODULE_FIRMWARE for tegra186, it's registered for 124/210 and
ensures the firmware is available at the appropriate time such as in
the initrd, else if the firmware is unavailable the driver fails with
the following errors:
tegra-xusb 3530000.usb: Direct firmware load for nvidia/tegra186/xusb.bin failed with error -2
tegra-xusb 3530000.usb: failed to request firmware: -2
tegra-xusb 3530000.usb: failed to load firmware: -2
tegra-xusb: probe of 3530000.usb failed with error -2
Linus Torvalds [Sun, 26 Jan 2020 20:23:04 +0000 (12:23 -0800)]
Merge tag 'io_uring-5.5-2020-01-26' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Fix for two regressions in this cycle, both reported by the postgresql
use case.
One removes the added restriction on who can submit IO, making it
possible for rings shared across forks to do so. The other fixes an
issue for the same kind of use case, where one exiting process would
cancel all IO"
* tag 'io_uring-5.5-2020-01-26' of git://git.kernel.dk/linux-block:
io_uring: don't cancel all work on process exit
Revert "io_uring: only allow submit from owning task"
Linus Torvalds [Sun, 26 Jan 2020 18:39:09 +0000 (10:39 -0800)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two last minute fixes, both in drivers.
The fnic one is a highly unlikely condition, but the RDMA one is a
recently introduced regression that causes a kernel warning to trigger
in every RDMA logon, which would be unsightly if it got into the final
release"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: RDMA/isert: Fix a recently introduced regression related to logout
scsi: fnic: do not queue commands during fwreset
Jens Axboe [Sun, 26 Jan 2020 17:17:12 +0000 (10:17 -0700)]
io_uring: don't cancel all work on process exit
If we're sharing the ring across forks, then one process exiting means
that we cancel ALL work and prevent future work. This is overly
restrictive. As long as we cancel the work associated with the files
from the current task, it's safe to let others persist. Normal fd close
on exit will still wait (and cancel) pending work.
Fixes: fcb323cc53e2 ("io_uring: io_uring: add support for async work inheriting files") Reported-by: Andres Freund <andres@anarazel.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
block: allow partitions on host aware zone devices
Host-aware SMR drives can be used with the commands to explicitly manage
zone state, but they can also be used as normal disks. In the former
case it makes perfect sense to allow partitions on them, in the latter
it does not, just like for host managed devices. Add a check to
add_partition to allow partitions on host aware devices, but give
up any zone management capabilities in that case, which also catches
the previously missed case of adding a partition vs just scanning it.
Because sd can rescan the attribute at runtime it needs to check if
a disk has partitions, for which a new helper is added to genhd.h.
Fixes: 5eac3eb30c9a ("block: Remove partition support for zoned block devices") Reported-by: Borislav Petkov <bp@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Jens Axboe [Sun, 26 Jan 2020 16:53:12 +0000 (09:53 -0700)]
Revert "io_uring: only allow submit from owning task"
This ends up being too restrictive for tasks that willingly fork and
share the ring between forks. Andres reports that this breaks his
postgresql work. Since we're close to 5.5 release, revert this change
for now.
Cc: stable@vger.kernel.org Fixes: 44d282796f81 ("io_uring: only allow submit from owning task") Reported-by: Andres Freund <andres@anarazel.de> Signed-off-by: Jens Axboe <axboe@kernel.dk>
David Howells [Sun, 26 Jan 2020 01:02:53 +0000 (01:02 +0000)]
afs: Fix characters allowed into cell names
The afs filesystem needs to prohibit certain characters from cell names,
such as '/', as these are used to form filenames in procfs, leading to
the following warning being generated:
WARNING: CPU: 0 PID: 3489 at fs/proc/generic.c:178
Fix afs_alloc_cell() to disallow nonprintable characters, '/', '@' and
names that begin with a dot.
Remove the check for "@cell" as that is then redundant.
This can be tested by running:
echo add foo/.bar 1.2.3.4 >/proc/fs/afs/cells
Note that we will also need to deal with:
- Names ending in ".invalid" shouldn't be passed to the DNS.
- Names that contain non-valid domainname chars shouldn't be passed to
the DNS.
- DNS replies that say "your-dns-needs-immediate-attention.<gTLD>" and
replies containing A records that say 127.0.53.53 should be
considered invalid.
[https://www.icann.org/en/system/files/files/name-collision-mitigation-01aug14-en.pdf]
but these need to be dealt with by the kafs-client DNS program rather
than the kernel.
Linus Torvalds [Sat, 25 Jan 2020 22:32:51 +0000 (14:32 -0800)]
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- fix ftrace relocation type filtering
- relax arch timer version check
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8955/1: virt: Relax arch timer version check during early boot
ARM: 8950/1: ftrace/recordmcount: filter relocation types
1) Off by one in mt76 airtime calculation, from Dan Carpenter.
2) Fix TLV fragment allocation loop condition in iwlwifi, from Luca
Coelho.
3) Don't confirm neigh entries when doing ipsec pmtu updates, from Xu
Wang.
4) More checks to make sure we only send TSO packets to lan78xx chips
that they can actually handle. From James Hughes.
5) Fix ip_tunnel namespace move, from William Dauchy.
6) Fix unintended packet reordering due to cooperation between
listification done by GRO and non-GRO paths. From Maxim
Mikityanskiy.
7) Add Jakub Kicincki formally as networking co-maintainer.
8) Info leak in airo ioctls, from Michael Ellerman.
9) IFLA_MTU attribute needs validation during rtnl_create_link(), from
Eric Dumazet.
10) Use after free during reload in mlxsw, from Ido Schimmel.
11) Dangling pointers are possible in tp->highest_sack, fix from Eric
Dumazet.
12) Missing *pos++ in various networking seq_next handlers, from Vasily
Averin.
13) CHELSIO_GET_MEM operation neds CAP_NET_ADMIN check, from Michael
Ellerman.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (109 commits)
firestream: fix memory leaks
net: cxgb3_main: Add CAP_NET_ADMIN check to CHELSIO_GET_MEM
net: bcmgenet: Use netif_tx_napi_add() for TX NAPI
tipc: change maintainer email address
net: stmmac: platform: fix probe for ACPI devices
net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path
net/mlx5e: kTLS, Remove redundant posts in TX resync flow
net/mlx5e: kTLS, Fix corner-case checks in TX resync flow
net/mlx5e: Clear VF config when switching modes
net/mlx5: DR, use non preemptible call to get the current cpu number
net/mlx5: E-Switch, Prevent ingress rate configuration of uplink rep
net/mlx5: DR, Enable counter on non-fwd-dest objects
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Fix lowest FDB pool size
net: Fix skb->csum update in inet_proto_csum_replace16().
netfilter: nf_tables: autoload modules from the abort path
netfilter: nf_tables: add __nft_chain_type_get()
netfilter: nf_tables_offload: fix check the chain offload flag
netfilter: conntrack: sctp: use distinct states for new SCTP connections
ipv6_route_seq_next should increase position index
...
Linus Torvalds [Sat, 25 Jan 2020 22:08:43 +0000 (14:08 -0800)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A couple of fixes have come in that would be good to include in this
release:
- A fix for amount of memory on Beaglebone Black. Surfaced now since
GRUB2 doesn't update memory size in the booted kernel.
- A fix to make SPI interfaces work on am43x-epos-evm.
- Small Kconfig fix for OPTEE (adds a depend on MMU) to avoid build
failures"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
tee: optee: Fix compilation issue with nommu
ARM: dts: am335x-boneblack-common: fix memory size
Wenwen Wang [Sat, 25 Jan 2020 14:33:29 +0000 (14:33 +0000)]
firestream: fix memory leaks
In fs_open(), 'vcc' is allocated through kmalloc() and assigned to
'atm_vcc->dev_data.' In the following execution, if an error occurs, e.g.,
there is no more free channel, an error code EBUSY or ENOMEM will be
returned. However, 'vcc' is not deallocated, leading to memory leaks. Note
that, in normal cases where fs_open() returns 0, 'vcc' will be deallocated
in fs_close(). But, if fs_open() fails, there is no guarantee that
fs_close() will be invoked.
To fix this issue, deallocate 'vcc' before the error code is returned.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sat, 25 Jan 2020 18:55:24 +0000 (10:55 -0800)]
Merge tag 'for-5.5-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"Here's a last minute fix for a regression introduced in this
development cycle.
There's a small chance of a silent corruption when device replace and
NOCOW data writes happen at the same time in one block group. Metadata
or COW data writes are unaffected.
The extra fixup patch is there to silence an unnecessary warning"
* tag 'for-5.5-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: dev-replace: remove warning for unknown return codes when finished
btrfs: scrub: Require mandatory block group RO for dev-replace
Linus Torvalds [Sat, 25 Jan 2020 18:46:07 +0000 (10:46 -0800)]
Merge tag 'pinctrl-v5.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fix from Linus Walleij:
"A single fix for the Intel Sunrisepoint pin controller that makes the
interrupts work properly on it"
* tag 'pinctrl-v5.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
Please pull and let me know if there is any problem.
Merge conflict: once merge with net-next, a contextual conflict will
appear in drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c
since the code moved in net-next.
To resolve, just delete ALL of the conflicting hunk from net.
So sorry for the small mess ..
For -stable v5.4:
('net/mlx5: Update the list of the PCI supported devices')
('net/mlx5: Fix lowest FDB pool size')
('net/mlx5e: kTLS, Fix corner-case checks in TX resync flow')
('net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path')
('net/mlx5: Eswitch, Prevent ingress rate configuration of uplink rep')
('net/mlx5e: kTLS, Remove redundant posts in TX resync flow')
('net/mlx5: DR, Enable counter on non-fwd-dest objects')
('net/mlx5: DR, use non preemptible call to get the current cpu number')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
caused by the previous patch ("btrfs: scrub: Require mandatory block
group RO for dev-replace"). Hitting ENOSPC is possible and could happen
when the block group is set read-only, preventing NOCOW writes to the
area that's being accessed by dev-replace.
This has happend with scratch devices of size 12G but not with 5G and
20G, so this is depends on timing and other activity on the filesystem.
The whole replace operation is restartable, the space state should be
examined by the user in any case.
The error code is propagated back to the ioctl caller so the kernel
warning is causing false alerts.
Michael Ellerman [Fri, 24 Jan 2020 09:41:44 +0000 (20:41 +1100)]
net: cxgb3_main: Add CAP_NET_ADMIN check to CHELSIO_GET_MEM
The cxgb3 driver for "Chelsio T3-based gigabit and 10Gb Ethernet
adapters" implements a custom ioctl as SIOCCHIOCTL/SIOCDEVPRIVATE in
cxgb_extension_ioctl().
One of the subcommands of the ioctl is CHELSIO_GET_MEM, which appears
to read memory directly out of the adapter and return it to userspace.
It's not entirely clear what the contents of the adapter memory
contains, but the assumption is that it shouldn't be accessible to all
users.
So add a CAP_NET_ADMIN check to the CHELSIO_GET_MEM case. Put it after
the is_offload() check, which matches two of the other subcommands in
the same function which also check for is_offload() and CAP_NET_ADMIN.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Thu, 23 Jan 2020 17:49:34 +0000 (09:49 -0800)]
net: bcmgenet: Use netif_tx_napi_add() for TX NAPI
Before commit 7587935cfa11 ("net: bcmgenet: move NAPI initialization to
ring initialization") moved the code, this used to be
netif_tx_napi_add(), but we lost that small semantic change in the
process, restore that.
Fixes: 7587935cfa11 ("net: bcmgenet: move NAPI initialization to ring initialization") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Doug Berger <opendmb@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Olof Johansson [Fri, 24 Jan 2020 20:05:32 +0000 (12:05 -0800)]
Merge tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Few minor fixes for omaps
Looks like we have wrong default memory size for beaglebone black,
it has at least 512 MB of RAM and not 256 MB. This causes an issue
when booted with GRUB2 that does not seem to pass memory info to
the kernel.
And for am43x-epos-evm the SPI pin directions need to be configured
for SPI to work.
* tag 'omap-for-fixes-whenever-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am43x-epos-evm: set data pin directions for spi0 and spi1
ARM: dts: am335x-boneblack-common: fix memory size
Tariq Toukan [Mon, 20 Jan 2020 11:42:00 +0000 (13:42 +0200)]
net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path
When TCP out-of-order is identified (unexpected tcp seq mismatch), driver
analyzes the packet and decides what handling should it get:
1. go to accelerated path (to be encrypted in HW),
2. go to regular xmit path (send w/o encryption),
3. drop.
Packets marked with skb->decrypted by the TLS stack in the TX flow skips
SW encryption, and rely on the HW offload.
Verify that such packets are never sent un-encrypted on the wire.
Add a WARN to catch such bugs, and prefer dropping the packet in these cases.
Tariq Toukan [Sun, 12 Jan 2020 14:22:14 +0000 (16:22 +0200)]
net/mlx5e: kTLS, Fix corner-case checks in TX resync flow
There are the following cases:
1. Packet ends before start marker: bypass offload.
2. Packet starts before start marker and ends after it: drop,
not supported, breaks contract with kernel.
3. packet ends before tls record info starts: drop,
this packet was already acknowledged and its record info
was released.
Add the above as comment in code.
Mind possible wraparounds of the TCP seq, replace the simple comparison
with a call to the TCP before() method.
In addition, remove logic that handles negative sync_len values,
as it became impossible.
Dmytro Linkin [Mon, 13 Jan 2020 11:46:13 +0000 (13:46 +0200)]
net/mlx5e: Clear VF config when switching modes
Currently VF in LEGACY mode are not able to go up. Also in OFFLOADS
mode, when switching to it first time, VF can go up independently to
his representor, which is not expected.
Perform clearing of VF config when switching modes and set link state
to AUTO as default value. Also, when switching to OFFLOADS mode set
link state to DOWN, which allow VF link state to be controlled by its
REP.
Fixes: 1ab2068a4c66 ("net/mlx5: Implement vports admin state backup/restore") Fixes: 556b9d16d3f5 ("net/mlx5: Clear VF's configuration on disabling SRIOV") Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Signed-off-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Erez Shitrit [Sun, 12 Jan 2020 06:57:59 +0000 (08:57 +0200)]
net/mlx5: DR, use non preemptible call to get the current cpu number
Use raw_smp_processor_id instead of smp_processor_id() otherwise we will
get the following trace in debug-kernel:
BUG: using smp_processor_id() in preemptible [00000000] code: devlink
caller is dr_create_cq.constprop.2+0x31d/0x970 [mlx5_core]
Call Trace:
dump_stack+0x9a/0xf0
debug_smp_processor_id+0x1f3/0x200
dr_create_cq.constprop.2+0x31d/0x970
genl_family_rcv_msg+0x5fd/0x1170
genl_rcv_msg+0xb8/0x160
netlink_rcv_skb+0x11e/0x340
Fixes: 297cccebdc5a ("net/mlx5: DR, Expose an internal API to issue RDMA operations") Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Sun, 12 Jan 2020 11:43:37 +0000 (13:43 +0200)]
net/mlx5: E-Switch, Prevent ingress rate configuration of uplink rep
Since the implementation relies on limiting the VF transmit rate to
simulate ingress rate limiting, and since either uplink representor or
ecpf are not associated with a VF, we limit the rate limit configuration
for those ports.
Fixes: fcb64c0f5640 ("net/mlx5: E-Switch, add ingress rate support") Signed-off-by: Eli Cohen <eli@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Meir Lichtinger [Thu, 12 Dec 2019 14:09:33 +0000 (16:09 +0200)]
net/mlx5: Update the list of the PCI supported devices
Add the upcoming ConnectX-7 device ID.
Fixes: 85327a9c4150 ("net/mlx5: Update the list of the PCI supported devices") Signed-off-by: Meir Lichtinger <meirl@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Paul Blakey [Tue, 31 Dec 2019 15:04:15 +0000 (17:04 +0200)]
net/mlx5: Fix lowest FDB pool size
The pool sizes represent the pool sizes in the fw. when we request
a pool size from fw, it will return the next possible group.
We track how many pools the fw has left and start requesting groups
from the big to the small.
When we start request 4k group, which doesn't exists in fw, fw
wants to allocate the next possible size, 64k, but will fail since
its exhausted. The correct smallest pool size in fw is 128 and not 4k.
Fixes: e52c28024008 ("net/mlx5: E-Switch, Add chains and priorities") Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
net: Fix skb->csum update in inet_proto_csum_replace16().
skb->csum is updated incorrectly, when manipulation for
NF_NAT_MANIP_SRC\DST is done on IPV6 packet.
Fix:
There is no need to update skb->csum in inet_proto_csum_replace16(),
because update in two fields a.) IPv6 src/dst address and b.) L4 header
checksum cancels each other for skb->csum calculation. Whereas
inet_proto_csum_replace4 function needs to update skb->csum, because
update in 3 fields a.) IPv4 src/dst address, b.) IPv4 Header checksum
and c.) L4 header checksum results in same diff as L4 Header checksum
for skb->csum calculation.
[ pablo@netfilter.org: a few comestic documentation edits ] Signed-off-by: Praveen Chaudhary <pchaudhary@linkedin.com> Signed-off-by: Zhenggen Xu <zxu@linkedin.com> Signed-off-by: Andy Stracner <astracner@linkedin.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
netfilter: nf_tables: autoload modules from the abort path
This patch introduces a list of pending module requests. This new module
list is composed of nft_module_request objects that contain the module
name and one status field that tells if the module has been already
loaded (the 'done' field).
In the first pass, from the preparation phase, the netlink command finds
that a module is missing on this list. Then, a module request is
allocated and added to this list and nft_request_module() returns
-EAGAIN. This triggers the abort path with the autoload parameter set on
from nfnetlink, request_module() is called and the module request enters
the 'done' state. Since the mutex is released when loading modules from
the abort phase, the module list is zapped so this is iteration occurs
over a local list. Therefore, the request_module() calls happen when
object lists are in consistent state (after fulling aborting the
transaction) and the commit list is empty.
On the second pass, the netlink command will find that it already tried
to load the module, so it does not request it again and
nft_request_module() returns 0. Then, there is a look up to find the
object that the command was missing. If the module was successfully
loaded, the command proceeds normally since it finds the missing object
in place, otherwise -ENOENT is reported to userspace.
This patch also updates nfnetlink to include the reason to enter the
abort phase, which is required for this new autoload module rationale.
Fixes: ec7470b834fe ("netfilter: nf_tables: store transaction list locally while requesting module") Reported-by: syzbot+29125d208b3dae9a7019@syzkaller.appspotmail.com Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This new helper function validates that unknown family and chain type
coming from userspace do not trigger an out-of-bound array access. Bail
out in case __nft_chain_type_get() returns NULL from
nft_chain_parse_hook().
Fixes: 9370761c56b6 ("netfilter: nf_tables: convert built-in tables/chains to chain types") Reported-by: syzbot+156a04714799b1d480bc@syzkaller.appspotmail.com Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Linus Torvalds [Fri, 24 Jan 2020 17:56:59 +0000 (09:56 -0800)]
Merge tag 'iommu-fixes-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"Two fixes:
- Fix NULL-ptr dereference bug in Intel IOMMU driver
- Properly save and restore AMD IOMMU performance counter registers
when testing if they are writable"
* tag 'iommu-fixes-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix IOMMU perf counter clobbering during init
iommu/vt-d: Call __dmar_remove_one_dev_info with valid pointer
Linus Torvalds [Fri, 24 Jan 2020 17:49:20 +0000 (09:49 -0800)]
Merge tag 'powerpc-5.5-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 5.5:
- Fix our hash MMU code to avoid having overlapping ids between user
and kernel, which isn't as bad as it sounds but led to crashes on
some machines.
- A fix for the Power9 XIVE interrupt code, which could return the
wrong interrupt state in obscure error conditions.
- A minor Kconfig fix for the recently added CONFIG_PPC_UV code.
Thanks to Aneesh Kumar K.V, Bharata B Rao, Cédric Le Goater, Frederic
Barrat"
* tag 'powerpc-5.5-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm/hash: Fix sharing context ids between kernel & userspace
powerpc/xive: Discard ESB load value when interrupt is invalid
powerpc: Ultravisor: Fix the dependencies for CONFIG_PPC_UV
Linus Torvalds [Fri, 24 Jan 2020 17:38:04 +0000 (09:38 -0800)]
Merge tag 'drm-fixes-2020-01-24' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"This one has a core mst fix and two i915 fixes. amdgpu just enables
some hw outside experimental.
The panfrost fix is a little bigger than I'd like at this stage but it
fixes a fairly fundamental problem with global shared buffers in that
driver, and since it's confined to that driver and I've taken a look
at it, I think it's fine to get into the tree now, so it can get
stable propagated as well.
core/mst:
- Fix SST branch device handling
amdgpu:
- enable renoir outside experimental
i915:
- Avoid overflow with huge userptr objects
- uAPI fix to correctly handle negative values in
engine->uabi_class/instance (cc: stable)
panfrost:
- Fix mapping of globally visible BO's (Boris)"
* tag 'drm-fixes-2020-01-24' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: remove the experimental flag for renoir
drm/panfrost: Add the panfrost_gem_mapping concept
drm/i915: Align engine->uabi_class/instance with i915_drm.h
drm/i915/userptr: fix size calculation
drm/dp_mst: Handle SST-only branch device case
Christophe Leroy [Thu, 23 Jan 2020 08:34:18 +0000 (08:34 +0000)]
lib: Reduce user_access_begin() boundaries in strncpy_from_user() and strnlen_user()
The range passed to user_access_begin() by strncpy_from_user() and
strnlen_user() starts at 'src' and goes up to the limit of userspace
although reads will be limited by the 'count' param.
On 32 bits powerpc (book3s/32) access has to be granted for each
256Mbytes segment and the cost increases with the number of segments to
unlock.