Linus Torvalds [Mon, 9 Mar 2020 00:36:22 +0000 (17:36 -0700)]
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"We've been accruing these for a couple of weeks, so the batch is a bit
bigger than usual.
Largest delta is due to a led-bl driver that is added -- there was a
miscommunication before the merge window and the driver didn't make it
in. Due to this, the platforms needing it regressed. At this point, it
seemed easier to add the new driver than unwind the changes.
Besides that, there are a handful of various fixes:
- AMD tee memory leak fix
- A handful of fixlets for i.MX SCU communication
- A few maintainers woke up and realized DEBUG_FS had been missing
for a while, so a few updates of that.
... and the usual collection of smaller fixes to various platforms"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (37 commits)
ARM: socfpga_defconfig: Add back DEBUG_FS
arm64: dts: socfpga: agilex: Fix gmac compatible
ARM: bcm2835_defconfig: Explicitly restore CONFIG_DEBUG_FS
arm64: dts: meson: fix gxm-khadas-vim2 wifi
arm64: dts: meson-sm1-sei610: add missing interrupt-names
ARM: meson: Drop unneeded select of COMMON_CLK
ARM: dts: bcm2711: Add pcie0 alias
ARM: dts: bcm283x: Add missing properties to the PWR LED
tee: amdtee: fix memory leak in amdtee_open_session()
ARM: OMAP2+: Fix compile if CONFIG_HAVE_ARM_SMCCC is not set
arm: dts: dra76x: Fix mmc3 max-frequency
ARM: dts: dra7: Add "dma-ranges" property to PCIe RC DT nodes
bus: ti-sysc: Fix 1-wire reset quirk
ARM: dts: r8a7779: Remove deprecated "renesas, rcar-sata" compatible value
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
...
Linus Torvalds [Mon, 9 Mar 2020 00:33:52 +0000 (17:33 -0700)]
Merge tag 'edac_urgent-2020-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
"Error reporting fix for synopsys_edac: do not overwrite partial
decoded error message (Sherry Sun)"
* tag 'edac_urgent-2020-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/synopsys: Do not print an error with back-to-back snprintf() calls
Linus Torvalds [Sun, 8 Mar 2020 15:49:44 +0000 (10:49 -0500)]
Merge tag 'char-misc-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are four small char/misc driver fixes for reported issues for
5.6-rc5.
These fixes are:
- binder fix for a potential use-after-free problem found (took two
tries to get it right)
- interconnect core fix
- altera-stapl driver fix
All four of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: prevent UAF for binderfs devices II
interconnect: Handle memory allocation errors
altera-stapl: altera_get_note: prevent write beyond end of 'key'
binder: prevent UAF for binderfs devices
Linus Torvalds [Sun, 8 Mar 2020 15:39:40 +0000 (10:39 -0500)]
Merge tag 'driver-core-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs fixes from Greg KH:
"Here are four small driver core / debugfs patches for 5.6-rc3:
- debugfs api cleanup now that all debugfs_create_regset32() callers
have been fixed up. This was waiting until after the -rc1 merge as
these fixes came in through different trees
- driver core sync state fixes based on reports of minor issues found
in the feature
All of these have been in linux-next with no reported issues"
* tag 'driver-core-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Skip unnecessary work when device doesn't have sync_state()
driver core: Add dev_has_sync_state()
driver core: Call sync_state() even if supplier has no consumers
debugfs: remove return value of debugfs_create_regset32()
Linus Torvalds [Sun, 8 Mar 2020 15:35:04 +0000 (10:35 -0500)]
Merge tag 'tty-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial fixes for 5.6-rc5
Just some small serial driver fixes, and a vt core fixup, full details
are:
- vt fixes for issues found by syzbot
- serdev fix for Apple boxes
- fsl_lpuart serial driver fixes
- MAINTAINER update for incorrect serial files
- new device ids for 8250_exar driver
- mvebu-uart fix
All of these have been in linux-next with no reported issues"
* tag 'tty-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: fsl_lpuart: free IDs allocated by IDA
Revert "tty: serial: fsl_lpuart: drop EARLYCON_DECLARE"
serdev: Fix detection of UART devices on Apple machines.
MAINTAINERS: Add missed files related to Synopsys DesignWare UART
serial: 8250_exar: add support for ACCES cards
tty:serial:mvebu-uart:fix a wrong return
vt: selection, push sel_lock up
vt: selection, push console lock down
Linus Torvalds [Sun, 8 Mar 2020 15:32:23 +0000 (10:32 -0500)]
Merge tag 'usb-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are some small USB and PHY driver fixes for reported issues for
5.6-rc5.
Included in here are:
- phy driver fixes
- new USB quirks
- USB cdns3 gadget driver fixes
- USB hub core fixes
All of these have been in linux-next with no reported issues"
* tag 'usb-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: dwc3: gadget: Update chain bit correctly when using sg list
usb: core: port: do error out if usb_autopm_get_interface() fails
usb: core: hub: do error out if usb_autopm_get_interface() fails
usb: core: hub: fix unhandled return by employing a void function
usb: storage: Add quirk for Samsung Fit flash
usb: quirks: add NO_LPM quirk for Logitech Screen Share
usb: usb251xb: fix regulator probe and error handling
phy: allwinner: Fix GENMASK misuse
usb: cdns3: gadget: toggle cycle bit before reset endpoint
usb: cdns3: gadget: link trb should point to next request
phy: mapphone-mdm6600: Fix timeouts by adding wake-up handling
phy: brcm-sata: Correct MDIO operations for 40nm platforms
phy: ti: gmii-sel: do not fail in case of gmii
phy: ti: gmii-sel: fix set of copy-paste errors
phy: core: Fix phy_get() to not return error on link creation failure
phy: mapphone-mdm6600: Fix write timeouts with shorter GPIO toggle interval
Linus Torvalds [Sun, 8 Mar 2020 01:52:55 +0000 (19:52 -0600)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Nothing particularly exciting, some small ODP regressions from the mmu
notifier rework, another bunch of syzkaller fixes, and a bug fix for a
botched syzkaller fix in the first rc pull request.
- Fix busted syzkaller fix in 'get_new_pps' - this turned out to
crash on certain HW configurations
- Bug fixes for various missed things in error unwinds
- Add a missing rcu_read_lock annotation in hfi/qib
- Fix two ODP related regressions from the recent mmu notifier
changes
- Several more syzkaller bugs in siw, RDMA netlink, verbs and iwcm
- Revert an old patch in CMA as it is now shown to not be allocating
port numbers properly"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/iwcm: Fix iwcm work deallocation
RDMA/siw: Fix failure handling during device creation
RDMA/nldev: Fix crash when set a QP to a new counter but QPN is missing
RDMA/odp: Ensure the mm is still alive before creating an implicit child
RDMA/core: Fix protection fault in ib_mr_pool_destroy
IB/mlx5: Fix implicit ODP race
IB/hfi1, qib: Ensure RCU is locked when accessing list
RDMA/core: Fix pkey and port assignment in get_new_pps
RMDA/cm: Fix missing ib_cm_destroy_id() in ib_cm_insert_listen()
RDMA/rw: Fix error flow during RDMA context initialization
RDMA/core: Fix use of logical OR in get_new_pps
Revert "RDMA/cma: Simplify rdma_resolve_addr() error flow"
Linus Torvalds [Sat, 7 Mar 2020 20:20:29 +0000 (14:20 -0600)]
Merge tag 'io_uring-5.6-2020-03-07' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"Here are a few io_uring fixes that should go into this release. This
contains:
- Removal of (now) unused io_wq_flush() and associated flag (Pavel)
- Fix cancelation lockup with linked timeouts (Pavel)
- Fix for potential use-after-free when freeing percpu ref for fixed
file sets
- io-wq cancelation fixups (Pavel)"
* tag 'io_uring-5.6-2020-03-07' of git://git.kernel.dk/linux-block:
io_uring: fix lockup with timeouts
io_uring: free fixed_file_data after RCU grace period
io-wq: remove io_wq_flush and IO_WQ_WORK_INTERNAL
io-wq: fix IO_WQ_WORK_NO_CANCEL cancellation
Linus Torvalds [Sat, 7 Mar 2020 20:14:38 +0000 (14:14 -0600)]
Merge tag 'block-5.6-2020-03-07' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"Here are a few fixes that should go into this release. This contains:
- Revert of a bad bcache patch from this merge window
- Removed unused function (Daniel)
- Fixup for the blktrace fix from Jan from this release (Cengiz)
- Fix of deeper level bfqq overwrite in BFQ (Carlo)"
* tag 'block-5.6-2020-03-07' of git://git.kernel.dk/linux-block:
block, bfq: fix overwrite of bfq_group pointer in bfq_find_set_group()
blktrace: fix dereference after null check
Revert "bcache: ignore pending signals when creating gc and allocator thread"
block: Remove used kblockd_schedule_work_on()
Linus Torvalds [Sat, 7 Mar 2020 18:00:13 +0000 (12:00 -0600)]
Merge tag 'media/v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a fix for the media controller links in both hantro driver and in
v4l2-mem2mem core
- some fixes for the pulse8-cec driver
- vicodec: handle alpha channel for RGB32 formats, as it may be used
- mc-entity.c: fix handling of pad flags
* tag 'media/v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: hantro: Fix broken media controller links
media: mc-entity.c: use & to check pad flags, not ==
media: v4l2-mem2mem.c: fix broken links
media: vicodec: process all 4 components for RGB32 formats
media: pulse8-cec: close serio in disconnect, not adap_free
media: pulse8-cec: INIT_DELAYED_WORK was called too late
Pavel Begunkov [Fri, 6 Mar 2020 22:15:22 +0000 (01:15 +0300)]
io_uring: fix lockup with timeouts
There is a recipe to deadlock the kernel: submit a timeout sqe with a
linked_timeout (e.g. test_single_link_timeout_ception() from liburing),
and SIGKILL the process.
Then, io_kill_timeouts() takes @ctx->completion_lock, but the timeout
isn't flagged with REQ_F_COMP_LOCKED, and will try to double grab it
during io_put_free() to cancel the linked timeout. Probably, the same
can happen with another io_kill_timeout() call site, that is
io_commit_cqring().
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Sat, 7 Mar 2020 14:12:47 +0000 (08:12 -0600)]
Merge tag 's390-5.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix panic in gup_fast on large pud by providing an implementation of
pud_write. This has been overlooked during migration to common gup
code.
- Fix unexpected write combining on PCI stores.
* tag 's390-5.6-5' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: Fix unexpected write combine on resource
s390/mm: fix panic in gup_fast on large pud
Linus Torvalds [Sat, 7 Mar 2020 14:10:34 +0000 (08:10 -0600)]
Merge tag 'powerpc-5.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 5.6:
- One fix for a recent regression to our breakpoint/watchpoint code.
- Another fix for our KUAP support, this time a missing annotation in
a rarely used path in signal handling.
- A fix for our handling of a CPU feature that effects the PMU, when
booting guests in some configurations.
- A minor fix to our linker script to explicitly include the .BTF
section.
Thanks to: Christophe Leroy, Desnes A. Nunes do Rosario, Leonardo
Bras, Naveen N. Rao, Ravi Bangoria, Stefan Berger"
* tag 'powerpc-5.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Fix missing KUAP disable in flush_coherent_icache()
powerpc: fix hardware PMU exception bug on PowerVM compatibility mode systems
powerpc: Include .BTF section
powerpc/watchpoint: Don't call dar_within_range() for Book3S
Linus Torvalds [Sat, 7 Mar 2020 14:04:54 +0000 (08:04 -0600)]
Merge tag 'for-linus-5.6b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Four fixes and a small cleanup patch:
- two fixes by Dongli Zhang fixing races in the xenbus driver
- two fixes by me fixing issues introduced in 5.6
- a small cleanup by Gustavo Silva replacing a zero-length array with
a flexible-array"
* tag 'for-linus-5.6b-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/blkfront: fix ring info addressing
xen/xenbus: fix locking
xenbus: req->err should be updated before req->state
xenbus: req->body should be updated before req->state
xen: Replace zero-length array with flexible-array member
Linus Torvalds [Sat, 7 Mar 2020 14:01:43 +0000 (08:01 -0600)]
Merge tag 'for-linus-2020-03-07' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux
Pull thread fixes from Christian Brauner:
"Here are a few hopefully uncontroversial fixes:
- Use RCU_INIT_POINTER() when initializing rcu protected members in
task_struct to fix sparse warnings.
- Add pidfd_fdinfo_test binary to .gitignore file"
* tag 'for-linus-2020-03-07' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
selftests: pidfd: Add pidfd_fdinfo_test in .gitignore
exit: Fix Sparse errors and warnings
fork: Use RCU_INIT_POINTER() instead of rcu_access_pointer()
Linus Torvalds [Sat, 7 Mar 2020 13:59:30 +0000 (07:59 -0600)]
Merge tag 'sound-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The regular "bump-in-the-middle" updates, containing mostly ASoC-
related fixes at this time. All changes are reasonably small.
A few entries are for ASoC and ALSA core parts (DAPM, PCM, topology)
for followups of the recent changes and potential buffer overflow by
snprintf(), while the rest are (both new and old) device-specific
fixes for Intel, meson, tas2562, rt1015, as well as the usual HD-audio
quirks"
* tag 'sound-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (25 commits)
ALSA: sgio2audio: Remove usage of dropped hw_params/hw_free functions
ALSA: hda/realtek - Enable the headset of ASUS B9450FA with ALC294
ALSA: hda/realtek - Fix silent output on Gigabyte X570 Aorus Master
ALSA: hda/realtek - Add Headset Button supported for ThinkPad X1
ALSA: hda/realtek - Add Headset Mic supported
ASoC: wm8741: Fix typo in Kconfig prompt
ASoC: stm32: sai: manage rebind issue
ASoC: SOF: Fix snd_sof_ipc_stream_posn()
ASoC: rt1015: modify pre-divider for sysclk
ASoC: rt1015: add operation callback function for rt1015_dai[]
ASoC: soc-component: tidyup snd_soc_pcm_component_sync_stop()
ASoC: dapm: Correct DAPM handling of active widgets during shutdown
ASoC: tas2562: Fix sample rate error message
ASoC: Intel: Skylake: Fix available clock counter incrementation
ASoC: soc-pcm/soc-compress: don't use snd_soc_dapm_stream_stop()
ASoC: meson: g12a: add tohdmitx reset
ASoC: pcm512x: Fix unbalanced regulator enable call in probe error path
ASoC: soc-core: fix for_rtd_codec_dai_rollback() macro
ASoC: topology: Fix memleak in soc_tplg_manifest_load()
ASoC: topology: Fix memleak in soc_tplg_link_elems_load()
...
Takashi Iwai [Sat, 7 Mar 2020 06:24:36 +0000 (07:24 +0100)]
Merge tag 'asoc-fix-v5.6-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.6
More fixes that have arrived since the merge window, spread out all
over. There's a few things like the operation callback addition for
rt1015 and the meson reset addition which add small new bits of
functionality to fix non-working systems, they're all very small and for
parts of newly added functionality.
Linus Torvalds [Fri, 6 Mar 2020 23:03:37 +0000 (17:03 -0600)]
Merge tag 'linux-kselftest-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest update from Shuah Khan:
"This consists of a cleanup patch to undo changes to global .gitignore
that added selftests/lkdtm objects and add them to a local
selftests/lkdtm/.gitignore.
Summary of Linus's comments on local vs. global gitignore scope:
- Keep local gitignore patterns in local files.
- Put only global gitignore patterns in the top-level gitignore file.
Local scope keeps things much better separated. It also incidentally
means that if a directory gets renamed, the gitignore file continues
to work unless in the case of renaming the actual files themselves
that are named in the gitignore"
* tag 'linux-kselftest-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftest/lkdtm: Use local .gitignore
Linus Torvalds [Fri, 6 Mar 2020 22:38:33 +0000 (16:38 -0600)]
Merge tag 'riscv-for-linus-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"This contains a handful of fixes that I would like to target for 5.6:
- A pair of fixes to module loading, which we hope solve the last of
the issues with module text being loaded too sparsely for our call
relocations.
- A Kconfig fix that disallows selecting memory models not supported
by NOMMU.
- A series of Kconfig updates to ease selecting the drivers necessary
to run on QEMU's virt platform.
- DTS updates for SiFive's HiFive Unleashed.
- A fix to our seccomp support that avoids mangling restartable
syscalls"
* tag 'riscv-for-linus-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: fix seccomp reject syscall code path
riscv: dts: Add GPIO reboot method to HiFive Unleashed DTS file
RISC-V: Select Goldfish RTC driver for QEMU virt machine
RISC-V: Select SYSCON Reboot and Poweroff for QEMU virt machine
RISC-V: Enable QEMU virt machine support in defconfigs
RISC-V: Add kconfig option for QEMU virt machine
riscv: Fix range looking for kernel image memblock
riscv: Force flat memory model with no-mmu
riscv: Change code model of module to medany to improve data accessing
riscv: avoid the PIC offset of static percpu data in module beyond 2G limits
Linus Torvalds [Fri, 6 Mar 2020 22:11:34 +0000 (16:11 -0600)]
Merge tag 'devicetree-fixes-for-5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
"Another batch of DT fixes. I think this should be the last of it, but
sending pull requests seems to cause people to send more fixes.
Summary:
- Fixes for warnings introduced by hierarchical PSCI binding changes
- Fixes for broken doc references due to DT schema conversions
- Several grammar and typo fixes
- Fix a bunch of dtc warnings in examples"
* tag 'devicetree-fixes-for-5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: arm: Fixup the DT bindings for hierarchical PSCI states
dt-bindings: power: Extend nodename pattern for power-domain providers
MAINTAINERS: update ALLWINNER CPUFREQ DRIVER entry
dt-bindings: bus: Drop empty compatible string in example
dt-bindings: power: Convert domain-idle-states bindings to json-schema
dt-bindings: arm: Fix cpu compatibles in the hierarchical example for PSCI
dt-bindings: arm: Correct links to idle states definitions
dt-bindings: mfd: Fix typo in file name of twl-familly.txt
dt-bindings: mfd: tps65910: Improve grammar
dt-bindings: mfd: zii,rave-sp: Fix a typo ("onborad")
dt-bindings: arm: fsl: fix APF6Dev compatible
dt-bindings: Fix dtc warnings in examples
docs: dt: fix several broken doc references
docs: dt: fix several broken references due to renames
MAINTAINERS: clean up PCIE DRIVER FOR CAVIUM THUNDERX
Linus Torvalds [Fri, 6 Mar 2020 20:55:27 +0000 (14:55 -0600)]
Merge tag 'filelock-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux
Pull file locking fixes from Jeff Layton:
"Just a couple of late-breaking patches for the file locking code. The
second patch (from yangerkun) fixes a rather nasty looking potential
use-after-free that should go to stable.
The other patch could technically wait for 5.7, but it's fairly
innocuous so I figured we might as well take it"
* tag 'filelock-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jlayton/linux:
locks: fix a potential use-after-free problem when wakeup a waiter
fcntl: Distribute switch variables for initialization
Linus Torvalds [Fri, 6 Mar 2020 20:50:16 +0000 (14:50 -0600)]
Merge tag 'spi-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A selection of small fixes, mostly for drivers, that have arrived
since the merge window. None of them are earth shattering in
themselves but all useful for affected systems"
* tag 'spi-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi_register_controller(): free bus id on error paths
spi: bcm63xx-hsspi: Really keep pll clk enabled
spi: atmel-quadspi: fix possible MMIO window size overrun
spi/zynqmp: remove entry that causes a cs glitch
spi: pxa2xx: Add CS control clock quirk
spi: spidev: Fix CS polarity if GPIO descriptors are used
spi: qup: call spi_qup_pm_resume_runtime before suspending
spi: spi-omap2-mcspi: Support probe deferral for DMA channels
spi: spi-omap2-mcspi: Handle DMA size restriction on AM65x
Linus Torvalds [Fri, 6 Mar 2020 20:48:30 +0000 (14:48 -0600)]
Merge tag 'regulator-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of small fixes, one for a minor issue in the stm32-vrefbuf
driver and a documentation fix in the Qualcomm code"
* tag 'regulator-fix-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: stm32-vrefbuf: fix a possible overshoot when re-enabling
regulator: qcom_spmi: Fix docs for PM8004
Linus Torvalds [Fri, 6 Mar 2020 20:47:06 +0000 (14:47 -0600)]
Merge tag 'hwmon-for-v5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Fix an error return in the adt7462 driver, bad voltage limits reported
by the xdpe12284 driver, and a broken documentation reference in the
adm1177 driver documentation"
* tag 'hwmon-for-v5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (adt7462) Fix an error return in ADT7462_REG_VOLT()
hwmon: (pmbus/xdpe12284) Add callback for vout limits conversion
docs: adm1177: fix a broken reference
Linus Torvalds [Fri, 6 Mar 2020 20:35:47 +0000 (14:35 -0600)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Here are another three arm64 fixes for 5.6, all pretty minor. Main
thing is fixing a silly bug in the fsl_imx8_ddr PMU driver where we
would zero the counters when disabling them.
- Fix misreporting of ASID limit when KPTI is enabled
- Fix busted NULL pointer checks for GICC structure in ACPI PMU code
- Avoid nobbling the "fsl_imx8_ddr" PMU counters when disabling them"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: context: Fix ASID limit in boot messages
drivers/perf: arm_pmu_acpi: Fix incorrect checking of gicc pointer
drivers/perf: fsl_imx8_ddr: Correct the CLEAR bit definition
Zhang Xiaoxu [Wed, 4 Mar 2020 02:24:29 +0000 (10:24 +0800)]
vgacon: Fix a UAF in vgacon_invert_region
When syzkaller tests, there is a UAF:
BUG: KASan: use after free in vgacon_invert_region+0x9d/0x110 at addr ffff880000100000
Read of size 2 by task syz-executor.1/16489
page:ffffea0000004000 count:0 mapcount:-127 mapping: (null)
index:0x0
page flags: 0xfffff00000000()
page dumped because: kasan: bad access detected
CPU: 1 PID: 16489 Comm: syz-executor.1 Not tainted
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
Call Trace:
[<ffffffffb119f309>] dump_stack+0x1e/0x20
[<ffffffffb04af957>] kasan_report+0x577/0x950
[<ffffffffb04ae652>] __asan_load2+0x62/0x80
[<ffffffffb090f26d>] vgacon_invert_region+0x9d/0x110
[<ffffffffb0a39d95>] invert_screen+0xe5/0x470
[<ffffffffb0a21dcb>] set_selection+0x44b/0x12f0
[<ffffffffb0a3bfae>] tioclinux+0xee/0x490
[<ffffffffb0a1d114>] vt_ioctl+0xff4/0x2670
[<ffffffffb0a0089a>] tty_ioctl+0x46a/0x1a10
[<ffffffffb052db3d>] do_vfs_ioctl+0x5bd/0xc40
[<ffffffffb052e2f2>] SyS_ioctl+0x132/0x170
[<ffffffffb11c9b1b>] system_call_fastpath+0x22/0x27
Memory state around the buggy address: ffff8800000fff00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 ffff8800000fff80: 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00
>ffff880000100000: ff ff ff ff ff ff ff ff ff ff ff ff ff
ff ff ff
It can be reproduce in the linux mainline by the program:
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <sys/ioctl.h>
#include <linux/vt.h>
struct tiocl_selection {
unsigned short xs; /* X start */
unsigned short ys; /* Y start */
unsigned short xe; /* X end */
unsigned short ye; /* Y end */
unsigned short sel_mode; /* selection mode */
};
When resize the screen, update the 'vc->vc_size_row' to the new_row_size,
but when 'set_origin' in 'vgacon_set_origin', vgacon use 'vga_vram_base'
for 'vc_origin' and 'vc_visible_origin', not 'vc_screenbuf'. It maybe
smaller than 'vc_screenbuf'. When TIOCLINUX, use the new_row_size to calc
the offset, it maybe larger than the vga_vram_size in vgacon driver, then
bad access.
Also, if set an larger screenbuf firstly, then set an more larger
screenbuf, when copy old_origin to new_origin, a bad access may happen.
So, If the screen size larger than vga_vram, resize screen should be
failed. This alse fix CVE-2020-8649 and CVE-2020-8647.
Linus pointed out that overflow checking seems absent. We're saved by
the existing bounds checks in vc_do_resize() with rather strict
limits:
if (cols > VC_RESIZE_MAXCOL || lines > VC_RESIZE_MAXROW)
return -EINVAL;
Fixes: 0aec4867dca14 ("[PATCH] SVGATextMode fix")
Reference: CVE-2020-8647 and CVE-2020-8649 Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
[danvet: augment commit message to point out overflow safety] Cc: stable@vger.kernel.org Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20200304022429.37738-1-zhangxiaoxu5@huawei.com
Ulf Hansson [Tue, 3 Mar 2020 15:07:47 +0000 (16:07 +0100)]
dt-bindings: arm: Fixup the DT bindings for hierarchical PSCI states
The hierarchical topology with power-domain should be described through
child nodes, rather than as currently described in the PSCI root node. Fix
this by adding a patternProperties with a corresponding reference to the
power-domain DT binding.
Additionally, update the example to conform to the new pattern, but also to
the adjusted domain-idle-state DT binding.
Fixes: a3f048b5424e ("dt: psci: Update DT bindings to support hierarchical PSCI states") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[robh: Add missing allOf, tweak power-domain node name] Signed-off-by: Rob Herring <robh@kernel.org>
Ulf Hansson [Tue, 3 Mar 2020 15:07:46 +0000 (16:07 +0100)]
dt-bindings: power: Extend nodename pattern for power-domain providers
The existing binding requires the nodename to have a '@', which is a bit
limiting for the wider use case. Therefore, let's extend the pattern to
allow either '@' or '-'.
Fixes: a3f048b5424e ("dt: psci: Update DT bindings to support hierarchical PSCI states") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[robh: drop example change] Signed-off-by: Rob Herring <robh@kernel.org>
Jens Axboe [Wed, 4 Mar 2020 14:25:50 +0000 (07:25 -0700)]
io_uring: free fixed_file_data after RCU grace period
The percpu refcount protects this structure, and we can have an atomic
switch in progress when exiting. This makes it unsafe to just free the
struct normally, and can trigger the following KASAN warning:
BUG: KASAN: use-after-free in percpu_ref_switch_to_atomic_rcu+0xfa/0x1b0
Read of size 1 at addr ffff888181a19a30 by task swapper/0/0
Fix this by punting the final exit and free of the struct to RCU, then
we know that it's safe to do so. Jann suggested the approach of using a
double rcu callback to achieve this. It's important that we do a nested
call_rcu() callback, as otherwise the free could be ordered before the
atomic switch, even if the latter was already queued.
Reported-by: syzbot+e017e49c39ab484ac87a@syzkaller.appspotmail.com Suggested-by: Jann Horn <jannh@google.com> Reviewed-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
yangerkun [Wed, 4 Mar 2020 07:25:56 +0000 (15:25 +0800)]
locks: fix a potential use-after-free problem when wakeup a waiter
'16306a61d3b7 ("fs/locks: always delete_block after waiting.")' add the
logic to check waiter->fl_blocker without blocked_lock_lock. And it will
trigger a UAF when we try to wakeup some waiter：
Thread 1 has create a write flock a on file, and now thread 2 try to
unlock and delete flock a, thread 3 try to add flock b on the same file.
Thread2 Thread3
flock syscall(create flock b)
...flock_lock_inode_wait
flock_lock_inode(will insert
our fl_blocked_member list
to flock a's fl_blocked_requests)
sleep
flock syscall(unlock)
...flock_lock_inode_wait
locks_delete_lock_ctx
...__locks_wake_up_blocks
__locks_delete_blocks(
b->fl_blocker = NULL)
...
break by a signal
locks_delete_block
b->fl_blocker == NULL &&
list_empty(&b->fl_blocked_requests)
success, return directly
locks_free_lock b
wake_up(&b->fl_waiter)
trigger UAF
Fix it by remove this logic, and this patch may also fix CVE-2019-19769.
Cc: stable@vger.kernel.org Fixes: 16306a61d3b7 ("fs/locks: always delete_block after waiting.") Signed-off-by: yangerkun <yangerkun@huawei.com> Signed-off-by: Jeff Layton <jlayton@kernel.org>
Carlo Nonato [Fri, 6 Mar 2020 12:27:31 +0000 (13:27 +0100)]
block, bfq: fix overwrite of bfq_group pointer in bfq_find_set_group()
The bfq_find_set_group() function takes as input a blkcg (which represents
a cgroup) and retrieves the corresponding bfq_group, then it updates the
bfq internal group hierarchy (see comments inside the function for why
this is needed) and finally it returns the bfq_group.
In the hierarchy update cycle, the pointer holding the correct bfq_group
that has to be returned is mistakenly used to traverse the hierarchy
bottom to top, meaning that in each iteration it gets overwritten with the
parent of the current group. Since the update cycle stops at root's
children (depth = 2), the overwrite becomes a problem only if the blkcg
describes a cgroup at a hierarchy level deeper than that (depth > 2). In
this case the root's child that happens to be also an ancestor of the
correct bfq_group is returned. The main consequence is that processes
contained in a cgroup at depth greater than 2 are wrongly placed in the
group described above by BFQ.
This commits fixes this problem by using a different bfq_group pointer in
the update cycle in order to avoid the overwrite of the variable holding
the original group reference.
Reported-by: Kwon Je Oh <kwonje.oh2@gmail.com> Signed-off-by: Carlo Nonato <carlo.nonato95@gmail.com> Signed-off-by: Paolo Valente <paolo.valente@linaro.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linus Torvalds [Fri, 6 Mar 2020 13:18:36 +0000 (07:18 -0600)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"7 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
arch/Kconfig: update HAVE_RELIABLE_STACKTRACE description
mm, hotplug: fix page online with DEBUG_PAGEALLOC compiled but not enabled
mm/z3fold.c: do not include rwlock.h directly
fat: fix uninit-memory access for partial initialized inode
mm: avoid data corruption on CoW fault into PFN-mapped VMA
mm: fix possible PMD dirty bit lost in set_pmd_migration_entry()
mm, numa: fix bad pmd by atomically check for pmd_trans_huge when marking page tables prot_numa
Michael Walle [Tue, 3 Mar 2020 17:42:59 +0000 (18:42 +0100)]
tty: serial: fsl_lpuart: free IDs allocated by IDA
Since commit 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node
dependence") the port line number can also be allocated by IDA, but in
case of an error the ID will no be removed again. More importantly, any
ID will be freed in remove(), even if it wasn't allocated but instead
fetched by of_alias_get_id(). If it was not allocated by IDA there will
be a warning:
WARN(1, "ida_free called for id=%d which is not allocated.\n", id);
Move the ID allocation more to the end of the probe() so that we still
can use plain return in the first error cases.
Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence") Signed-off-by: Michael Walle <michael@walle.cc> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200303174306.6015-3-michael@walle.cc Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This broke the earlycon on LS1021A processors because the order of the
earlycon_setup() functions were changed. Before the commit the normal
lpuart32_early_console_setup() was called. After the commit the
lpuart32_imx_early_console_setup() is called instead.
Ronald Tschalär [Tue, 11 Feb 2020 19:47:23 +0000 (11:47 -0800)]
serdev: Fix detection of UART devices on Apple machines.
On Apple devices the _CRS method returns an empty resource template, and
the resource settings are instead provided by the _DSM method. But
commit 33364d63c75d6182fa369cea80315cf1bb0ee38e (serdev: Add ACPI
devices by ResourceSource field) changed the search for serdev devices
to require valid, non-empty resource template, thereby breaking Apple
devices and causing bluetooth devices to not be found.
This expands the check so that if we don't find a valid template, and
we're on an Apple machine, then just check for the device being an
immediate child of the controller and having a "baud" property.
save_stack_trace_tsk_reliable() is not the only function providing the
reliable stack traces anymore. Architecture might define ARCH_STACKWALK
which provides a newer stack walking interface and has
arch_stack_walk_reliable() function. Update the description accordingly.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Miroslav Benes <mbenes@suse.cz> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Link: http://lkml.kernel.org/r/20200120154042.9934-1-mbenes@suse.cz Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vlastimil Babka [Fri, 6 Mar 2020 06:28:42 +0000 (22:28 -0800)]
mm, hotplug: fix page online with DEBUG_PAGEALLOC compiled but not enabled
Commit cd02cf1aceea ("mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC")
fixed memory hotplug with debug_pagealloc enabled, where onlining a page
goes through page freeing, which removes the direct mapping. Some arches
don't like when the page is not mapped in the first place, so
generic_online_page() maps it first. This is somewhat wasteful, but
better than special casing page freeing fast paths.
The commit however missed that DEBUG_PAGEALLOC configured doesn't mean
it's actually enabled. One has to test debug_pagealloc_enabled() since 031bc5743f15 ("mm/debug-pagealloc: make debug-pagealloc boottime
configurable"), or alternatively debug_pagealloc_enabled_static() since 8e57f8acbbd1 ("mm, debug_pagealloc: don't rely on static keys too early"),
but this is not done.
As a result, a s390 kernel with DEBUG_PAGEALLOC configured but not enabled
will crash:
Fix this by checking debug_pagealloc_enabled_static() before calling
kernel_map_pages(). Backports for kernel before 5.5 should use
debug_pagealloc_enabled() instead. Also add comments.
Fixes: cd02cf1aceea ("mm/hotplug: fix an imbalance with DEBUG_PAGEALLOC") Reported-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: <stable@vger.kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Qian Cai <cai@lca.pw> Link: http://lkml.kernel.org/r/20200224094651.18257-1-vbabka@suse.cz Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OGAWA Hirofumi [Fri, 6 Mar 2020 06:28:36 +0000 (22:28 -0800)]
fat: fix uninit-memory access for partial initialized inode
When get an error in the middle of reading an inode, some fields in the
inode might be still not initialized. And then the evict_inode path may
access those fields via iput().
To fix, this makes sure that inode fields are initialized.
The warning happens on failed __copy_from_user_inatomic() which tries to
copy data into a CoW page.
This happens because of race between MADV_DONTNEED and CoW page fault:
CPU0 CPU1
handle_mm_fault()
do_wp_page()
wp_page_copy()
do_wp_page()
madvise(MADV_DONTNEED)
zap_page_range()
zap_pte_range()
ptep_get_and_clear_full()
<TLB flush>
__copy_from_user_inatomic()
sees empty PTE and fails
WARN_ON_ONCE(1)
clear_page()
The solution is to re-try __copy_from_user_inatomic() under PTL after
checking that PTE is matches the orig_pte.
The second copy attempt can still fail, like due to non-readable PTE, but
there's nothing reasonable we can do about, except clearing the CoW page.
Reported-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Tested-by: Jeff Moyer <jmoyer@redhat.com> Cc: <stable@vger.kernel.org> Cc: Justin He <Justin.He@arm.com> Cc: Dan Williams <dan.j.williams@intel.com> Link: http://lkml.kernel.org/r/20200218154151.13349-1-kirill.shutemov@linux.intel.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Huang Ying [Fri, 6 Mar 2020 06:28:29 +0000 (22:28 -0800)]
mm: fix possible PMD dirty bit lost in set_pmd_migration_entry()
In set_pmd_migration_entry(), pmdp_invalidate() is used to change PMD
atomically. But the PMD is read before that with an ordinary memory
reading. If the THP (transparent huge page) is written between the PMD
reading and pmdp_invalidate(), the PMD dirty bit may be lost, and cause
data corruption. The race window is quite small, but still possible in
theory, so need to be fixed.
The race is fixed via using the return value of pmdp_invalidate() to get
the original content of PMD, which is a read/modify/write atomic
operation. So no THP writing can occur in between.
The race has been introduced when the THP migration support is added in
the commit 616b8371539a ("mm: thp: enable thp migration in generic path").
But this fix depends on the commit d52605d7cb30 ("mm: do not lose dirty
and accessed bits in pmdp_invalidate()"). So it's easy to be backported
after v4.16. But the race window is really small, so it may be fine not
to backport the fix at all.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: "Huang, Ying" <ying.huang@intel.com> Reviewed-by: Zi Yan <ziy@nvidia.com> Reviewed-by: William Kucharski <william.kucharski@oracle.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: <stable@vger.kernel.org> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@kernel.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Link: http://lkml.kernel.org/r/20200220075220.2327056-1-ying.huang@intel.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mel Gorman [Fri, 6 Mar 2020 06:28:26 +0000 (22:28 -0800)]
mm, numa: fix bad pmd by atomically check for pmd_trans_huge when marking page tables prot_numa
: A user reported a bug against a distribution kernel while running a
: proprietary workload described as "memory intensive that is not swapping"
: that is expected to apply to mainline kernels. The workload is
: read/write/modifying ranges of memory and checking the contents. They
: reported that within a few hours that a bad PMD would be reported followed
: by a memory corruption where expected data was all zeros. A partial
: report of the bad PMD looked like
:
: [ 5195.338482] ../mm/pgtable-generic.c:33: bad pmd ffff8888157ba008(000002e0396009e2)
: [ 5195.341184] ------------[ cut here ]------------
: [ 5195.356880] kernel BUG at ../mm/pgtable-generic.c:35!
: ....
: [ 5195.410033] Call Trace:
: [ 5195.410471] [<ffffffff811bc75d>] change_protection_range+0x7dd/0x930
: [ 5195.410716] [<ffffffff811d4be8>] change_prot_numa+0x18/0x30
: [ 5195.410918] [<ffffffff810adefe>] task_numa_work+0x1fe/0x310
: [ 5195.411200] [<ffffffff81098322>] task_work_run+0x72/0x90
: [ 5195.411246] [<ffffffff81077139>] exit_to_usermode_loop+0x91/0xc2
: [ 5195.411494] [<ffffffff81003a51>] prepare_exit_to_usermode+0x31/0x40
: [ 5195.411739] [<ffffffff815e56af>] retint_user+0x8/0x10
:
: Decoding revealed that the PMD was a valid prot_numa PMD and the bad PMD
: was a false detection. The bug does not trigger if automatic NUMA
: balancing or transparent huge pages is disabled.
:
: The bug is due a race in change_pmd_range between a pmd_trans_huge and
: pmd_nond_or_clear_bad check without any locks held. During the
: pmd_trans_huge check, a parallel protection update under lock can have
: cleared the PMD and filled it with a prot_numa entry between the transhuge
: check and the pmd_none_or_clear_bad check.
:
: While this could be fixed with heavy locking, it's only necessary to make
: a copy of the PMD on the stack during change_pmd_range and avoid races. A
: new helper is created for this as the check if quite subtle and the
: existing similar helpful is not suitable. This passed 154 hours of
: testing (usually triggers between 20 minutes and 24 hours) without
: detecting bad PMDs or corruption. A basic test of an autonuma-intensive
: workload showed no significant change in behaviour.
Although Mel withdrew the patch on the face of LKML comment
https://lkml.org/lkml/2017/4/10/922 the race window aforementioned is
still open, and we have reports of Linpack test reporting bad residuals
after the bad PMD warning is observed. In addition to that, bad
rss-counter and non-zero pgtables assertions are triggered on mm teardown
for the task hitting the bad PMD.
host kernel: mm/pgtable-generic.c:40: bad pmd 00000000b3152f68(8000000d2d2008e7)
....
host kernel: BUG: Bad rss-counter state mm:00000000b583043d idx:1 val:512
host kernel: BUG: non-zero pgtables_bytes on freeing mm: 4096
The issue is observed on a v4.18-based distribution kernel, but the race
window is expected to be applicable to mainline kernels, as well.
[akpm@linux-foundation.org: fix comment typo, per Rafael] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Rafael Aquini <aquini@redhat.com> Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> Cc: Zi Yan <zi.yan@cs.rutgers.edu> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@suse.com> Link: http://lkml.kernel.org/r/20200216191800.22423-1-aquini@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 6 Mar 2020 12:49:09 +0000 (06:49 -0600)]
Merge tag 'acpi-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI documentation fix from Rafael Wysocki:
"Fix Sphinx format warinings in an ACPI fan document added recently
(Randy Dunlap)"
* tag 'acpi-5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Documentation/admin-guide/acpi: fix fan_performance_states.rst warnings
Linus Torvalds [Fri, 6 Mar 2020 12:45:20 +0000 (06:45 -0600)]
Merge tag 'drm-fixes-2020-03-06' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Weekly fixes round, looks like a few people woke up, got a bunch of
fixes across the drivers. Bit bigger than I'd like but they all seem
fine and hopefully it quiets down now.
sun4i, kirin, mediatek and exynos on the ARM side. virtio-gpu and core
have some mmap fixes, and there is a dma-buf leak. one ttm fence leak
is also fixed.
Otherwise it's mostly amdgpu and i915.
One of the i915 fixes is for a very long latency I was seeing (using
latencytop) running gnome-shell locally when using firefox and eating
nearly all my RAM, it really helps with desktop responsiveness esp
when firefox is chewing a lot.
dma-buf:
- fix memory leak
core:
- shmem object mmap fix.
ttm:
- Fix fence leak in ttm_buffer_object_transfer().
amdgpu:
- Gfx reset fix for gfx9, 10
- Fix for gfx10
- DP MST fix
- DCC fix
- Renoir power fixes
- Navi power fix
i915:
- Break up long lists of object reclaim with cond_resched()
- PSR probe fix
- TGL workarounds
- Selftest return value fix
- Drop timeline mutex while waiting for retirement
- Wait for OA configuration completion before writes to OA buffer
virtio:
- Fix resource id creation race in virtio.
- mmap fixes
sun4i:
- Fixes for sun4i VI layer format support.
kirin:
- kirin: Revert "Fix for hikey620 display offset problem"
exynos:
- fix a kernel oops problem in case that driver is loaded as module.
- fix a regulator warning issue when I2C DDC adapter cannot be gathered.
- print out an error message only in error case excepting -EPROBE_DEFER.
mediatek:
- overlay, cursor and gce fixes"
`
* tag 'drm-fixes-2020-03-06' of git://anongit.freedesktop.org/drm/drm: (38 commits)
drm/amdgpu/display: navi1x copy dcn watermark clock settings to smu resume from s3 (v2)
drm/amd/powerplay: map mclk to fclk for COMBINATIONAL_BYPASS case
drm/amd/powerplay: fix pre-check condition for setting clock range
drm/amd/display: fix dcc swath size calculations on dcn1
drm/amd/display: Clear link settings on MST disable connector
drm/amdgpu: disable 3D pipe 1 on Navi1x
drm/amdgpu: clean wptr on wb when gpu recovery
drm: kirin: Revert "Fix for hikey620 display offset problem"
drm/i915/gt: Drop the timeline->mutex as we wait for retirement
drm/i915/perf: Reintroduce wait on OA configuration completion
drm/sun4i: Fix DE2 VI layer format support
drm/sun4i: Add separate DE3 VI layer formats
drm/sun4i: de2/de3: Remove unsupported VI layer formats
drm/i915/selftests: Fix return in assert_mmap_offset()
drm/i915: Protect i915_request_await_start from early waits
drm/i915/tgl: Add Wa_1608008084
drm/i915/tgl: Add Wa_22010178259:tgl
drm/i915: Program MBUS with rmw during initialization
drm/i915/psr: Force PSR probe only after full initialization
drm/i915/gem: Break up long lists of object reclaim
...
ALSA: sgio2audio: Remove usage of dropped hw_params/hw_free functions
Commit ee88f4ebe575 ("ALSA: mips: Use managed buffer allocation") removed
superfluous hw_params/hw_free callbacks, but forgot to remove them where
they were used.
Dave Airlie [Thu, 5 Mar 2020 23:18:18 +0000 (09:18 +1000)]
Merge tag 'drm-intel-fixes-2020-03-05' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.6-rc5:
- Break up long lists of object reclaim with cond_resched()
- PSR probe fix
- TGL workarounds
- Selftest return value fix
- Drop timeline mutex while waiting for retirement
- Wait for OA configuration completion before writes to OA buffer
Dave Airlie [Thu, 5 Mar 2020 19:40:12 +0000 (05:40 +1000)]
Merge tag 'drm-misc-fixes-2020-03-05' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v5.6.rc5:
- dma-buf fix memory leak
- Fix resource id creation race in virtio.
- Various mmap fixes.
- Fix fence leak in ttm_buffer_object_transfer().
- Fixes for sun4i VI layer format support.
- kirin: Revert "Fix for hikey620 display offset problem"
Tycho Andersen [Sat, 8 Feb 2020 15:18:17 +0000 (08:18 -0700)]
riscv: fix seccomp reject syscall code path
If secure_computing() rejected a system call, we were previously setting
the system call number to -1, to indicate to later code that the syscall
failed. However, if something (e.g. a user notification) was sleeping, and
received a signal, we may set a0 to -ERESTARTSYS and re-try the system call
again.
In this case, seccomp "denies" the syscall (because of the signal), and we
would set a7 to -1, thus losing the value of the system call we want to
restart.
Instead, let's return -1 from do_syscall_trace_enter() to indicate that the
syscall was rejected, so we don't clobber the value in case of -ERESTARTSYS
or whatever.
This commit fixes the user_notification_signal seccomp selftest on riscv to
no longer hang. That test expects the system call to be re-issued after the
signal, and it wasn't due to the above bug. Now that it is, everything
works normally.
Note that in the ptrace (tracer) case, the tracer can set the register
values to whatever they want, so we still need to keep the code that
handles out-of-bounds syscalls. However, we can drop the comment.
We can also drop syscall_set_nr(), since it is no longer used anywhere, and
the code that re-loads the value in a7 because of it.
Cengiz Can [Wed, 4 Mar 2020 10:58:19 +0000 (13:58 +0300)]
blktrace: fix dereference after null check
There was a recent change in blktrace.c that added a RCU protection to
`q->blk_trace` in order to fix a use-after-free issue during access.
However the change missed an edge case that can lead to dereferencing of
`bt` pointer even when it's NULL:
Coverity static analyzer marked this as a FORWARD_NULL issue with CID 1460458.
```
/kernel/trace/blktrace.c: 1904 in sysfs_blk_trace_attr_store()
1898 ret = 0;
1899 if (bt == NULL)
1900 ret = blk_trace_setup_queue(q, bdev);
1901
1902 if (ret == 0) {
1903 if (attr == &dev_attr_act_mask)
>>> CID 1460458: Null pointer dereferences (FORWARD_NULL)
>>> Dereferencing null pointer "bt".
1904 bt->act_mask = value;
1905 else if (attr == &dev_attr_pid)
1906 bt->pid = value;
1907 else if (attr == &dev_attr_start_lba)
1908 bt->start_lba = value;
1909 else if (attr == &dev_attr_end_lba)
```
Added a reassignment with RCU annotation to fix the issue.
Fixes: c780e86dd48 ("blktrace: Protect q->blk_trace with RCU") Cc: stable@vger.kernel.org Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Bob Liu <bob.liu@oracle.com> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Cengiz Can <cengiz@kernel.wtf> Signed-off-by: Jens Axboe <axboe@kernel.dk>
Andy Shevchenko [Thu, 5 Mar 2020 12:31:08 +0000 (14:31 +0200)]
MAINTAINERS: Add missed files related to Synopsys DesignWare UART
8250_dw has been split to library part and the driver, the library
is being used by 8250_lpss, which represents Synosys DesignWare UART
(with optional Synopsys Designware DMA) enumerated by PCI.
Add missed above mentioned files to the database record for review.
Anup Patel [Tue, 3 Dec 2019 03:49:37 +0000 (03:49 +0000)]
RISC-V: Select SYSCON Reboot and Poweroff for QEMU virt machine
The SYSCON Reboot and Poweroff drivers can be used on QEMU virt machine
to reboot or poweroff the system hence we select these drivers using
QEMU virt machine kconfig option.
Anup Patel [Tue, 3 Dec 2019 03:49:34 +0000 (03:49 +0000)]
RISC-V: Enable QEMU virt machine support in defconfigs
We have kconfig option for QEMU virt machine so let's enable it
in RV32 and RV64 defconfigs. Also, we remove various VIRTIO configs
from RV32 and RV64 defconfigs because these are now selected by
QEMU virt machine kconfig option.
Linus Torvalds [Thu, 5 Mar 2020 18:23:22 +0000 (12:23 -0600)]
Merge tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V update from Wei Liu:
- Update MAINTAINERS file for Hyper-V
- One cleanup patch for Hyper-V HID driver
* tag 'hyperv-fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
HID: hyperv: NULL check before some freeing functions is not needed.
Hyper-V: add myself as a maintainer
Hyper-V: Drop Sasha Levin from the Hyper-V maintainers
Linus Torvalds [Thu, 5 Mar 2020 18:19:34 +0000 (12:19 -0600)]
Merge tag 'dmaengine-fix-5.6-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"A bunch of driver fixes:
- Doc updates to clean warnings for dmaengine
- Fixes for newly added Intel idxd driver
- More fixes for newly added TI k3-udma driver
- Fixes for IMX and Tegra drivers"
* tag 'dmaengine-fix-5.6-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: imx-sdma: Fix the event id check to include RX event for UART6
dmaengine: tegra-apb: Prevent race conditions of tasklet vs free list
dmaengine: tegra-apb: Fix use-after-free
dmaengine: imx-sdma: fix context cache
dmaengine: idxd: wq size configuration needs to check global max size
dmaengine: idxd: sysfs input of wq incorrect wq type should return error
dmaengine: coh901318: Fix a double lock bug in dma_tc_handle()
dmaengine: idxd: correct reserved token calculation
dmaengine: ti: k3-udma: Fix terminated transfer handling
dmaengine: ti: k3-udma: Use the channel direction in pause/resume functions
dmaengine: ti: k3-udma: Use the TR counter helper for slave_sg and cyclic
dmaengine: ti: k3-udma: Move the TR counter calculation to helper function
dmaengine: ti: k3-udma: Workaround for RX teardown with stale data in peer
dmaengine: ti: k3-udma: Use ktime/usleep_range based TX completion check
dmaengine: idxd: Fix error handling in idxd_wq_cdev_dev_setup()
dmaengine: doc: fix warnings/issues of client.rst
dmaengine: idxd: fix runaway module ref count on device driver bind
Juergen Gross [Thu, 5 Mar 2020 15:51:29 +0000 (16:51 +0100)]
xen/blkfront: fix ring info addressing
Commit 0265d6e8ddb890 ("xen/blkfront: limit allocated memory size to
actual use case") made struct blkfront_ring_info size dynamic. This is
fine when running with only one queue, but with multiple queues the
addressing of the single queues has to be adapted as the structs are
allocated in an array.
Fixes: 0265d6e8ddb890 ("xen/blkfront: limit allocated memory size to actual use case") Reported-by: Sander Eikelenboom <linux@eikelenboom.it> Tested-by: Sander Eikelenboom <linux@eikelenboom.it> Signed-off-by: Juergen Gross <jgross@suse.com> Acked-by: Roger Pau Monné <roger.pau@citrix.com> Link: https://lore.kernel.org/r/20200305155129.28326-1-jgross@suse.com Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Juergen Gross [Thu, 5 Mar 2020 10:03:23 +0000 (11:03 +0100)]
xen/xenbus: fix locking
Commit 060eabe8fbe726 ("xenbus/backend: Protect xenbus callback with
lock") introduced a bug by holding a lock while calling a function
which might schedule.
Fix that by using a semaphore instead.
Fixes: 060eabe8fbe726 ("xenbus/backend: Protect xenbus callback with lock") Signed-off-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20200305100323.16736-1-jgross@suse.com Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Below is sample callstack when the issue is reproduced on purpose by
reordering the updates of req->body and req->state and adding delay in
code between updates of req->state and req->body.
The virt_rmb() is added in the 'true' path of test_reply(). The "while"
is changed to "do while" so that test_reply() is used as a read memory
barrier.
xen: Replace zero-length array with flexible-array member
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
Hersen Wu [Thu, 13 Feb 2020 15:50:13 +0000 (10:50 -0500)]
drm/amdgpu/display: navi1x copy dcn watermark clock settings to smu resume from s3 (v2)
This interface is for dGPU Navi1x. Linux dc-pplib interface depends
on window driver dc implementation.
For Navi1x, clock settings of dcn watermarks are fixed. the settings
should be passed to smu during boot up and resume from s3.
boot up: dc calculate dcn watermark clock settings within dc_create,
dcn20_resource_construct, then call pplib functions below to pass
the settings to smu:
smu_set_watermarks_for_clock_ranges
smu_set_watermarks_table
navi10_set_watermarks_table
smu_write_watermarks_table
For Renoir, clock settings of dcn watermark are also fixed values.
dc has implemented different flow for window driver:
dc_hardware_init / dc_set_power_state
dcn10_init_hw
notify_wm_ranges
set_wm_ranges
For Linux
smu_set_watermarks_for_clock_ranges
renoir_set_watermarks_table
smu_write_watermarks_table
Prike Liang [Mon, 2 Mar 2020 01:36:15 +0000 (09:36 +0800)]
drm/amd/powerplay: fix pre-check condition for setting clock range
This fix will handle some MP1 FW issue like as mclk dpm table in renoir has a reverse
dpm clock layout and a zero frequency dpm level as following case.
Josip Pavic [Fri, 21 Feb 2020 17:26:19 +0000 (12:26 -0500)]
drm/amd/display: fix dcc swath size calculations on dcn1
[Why]
Swath sizes are being calculated incorrectly. The horizontal swath size
should be the product of block height, viewport width, and bytes per
element, but the calculation uses viewport height instead of width. The
vertical swath size is similarly incorrectly calculated. The effect of
this is that we report the wrong DCC caps.
[How]
Use viewport width in the horizontal swath size calculation and viewport
height in the vertical swath size calculation.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
when we disable MST we should clear the cur link settings (lane_count=0 is
good enough). This will cause us to not reallocate payloads earlier than
expected and not throw the warning
The Gigabyte X570 Aorus Master motherboard with ALC1220 codec
requires a similar workaround for Clevo laptops to enforce the
DAC/mixer connection path. Set up a quirk entry for that.
Lucas Tanure [Sat, 29 Feb 2020 17:30:07 +0000 (17:30 +0000)]
HID: hyperv: NULL check before some freeing functions is not needed.
Fix below warnings reported by coccicheck:
drivers/hid/hid-hyperv.c:197:2-7: WARNING: NULL check before some freeing functions is not needed.
drivers/hid/hid-hyperv.c:211:2-7: WARNING: NULL check before some freeing functions is not needed.
Signed-off-by: Lucas Tanure <tanure@linux.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Wei Liu <wei.liu@kernel.org> Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Wei Liu <wei.liu@kernel.org>
Commit b30d8cf5e171 ("dt-bindings: opp: Convert Allwinner H6 OPP to a
schema") converted in Documentation/devicetree/bindings/opp/ the file
sun50i-nvmem-cpufreq.txt to allwinner,sun50i-h6-operating-points.yaml.
Since then, ./scripts/get_maintainer.pl --self-test complains:
warning: no file matches \
F: Documentation/devicetree/bindings/opp/sun50i-nvmem-cpufreq.txt
Adjust the file pattern in the ALLWINNER CPUFREQ DRIVER entry.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by: Rob Herring <robh@kernel.org>
powerpc/mm: Fix missing KUAP disable in flush_coherent_icache()
Stefan reported a strange kernel fault which turned out to be due to a
missing KUAP disable in flush_coherent_icache() called from
flush_icache_range().
This path through handle_rt_signal64() to setup_trampoline() and
flush_icache_range() is only triggered by 64-bit processes that have
unmapped their VDSO, which is rare.
flush_icache_range() takes a range of addresses to flush. In
flush_coherent_icache() we implement an optimisation for CPUs where we
know we don't actually have to flush the whole range, we just need to
do a single icbi.
However we still execute the icbi on the user address of the start of
the range we're flushing. On CPUs that also implement KUAP (Power9)
that leads to the spurious fault above.
We should be able to pass any address, including a kernel address, to
the icbi on these CPUs, which would avoid any interaction with KUAP.
But I don't want to make that change in a bug fix, just in case it
surfaces some strange behaviour on some CPU.
So for now just disable KUAP around the icbi. Note the icbi is treated
as a load, so we allow read access, not write as you'd expect.
Fixes: 890274c2dc4c ("powerpc/64s: Implement KUAP for Radix MMU") Cc: stable@vger.kernel.org # v5.2+ Reported-by: Stefan Berger <stefanb@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200303235708.26004-1-mpe@ellerman.id.au
Yintian Tao [Fri, 28 Feb 2020 06:24:42 +0000 (14:24 +0800)]
drm/amdgpu: clean wptr on wb when gpu recovery
The TDR will be randomly failed due to compute ring
test failure. If the compute ring wptr & 0x7ff(ring_buf_mask)
is 0x100 then after map mqd the compute ring rptr will be
synced with 0x100. And the ring test packet size is also 0x100.
Then after invocation of amdgpu_ring_commit, the cp will not
really handle the packet on the ring buffer because rptr is equal to wptr.
Signed-off-by: Yintian Tao <yttao@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Monk Liu <Monk.Liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dave Airlie [Thu, 5 Mar 2020 02:34:50 +0000 (12:34 +1000)]
Merge tag 'exynos-drm-fixes-for-v5.6-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
Three fixups
- fix a kernel oops problem in case that driver is loaded as module.
- fix a regulator warning issue when I2C DDC adapter cannot be gathered.
- print out an error message only in error case excepting -EPROBE_DEFER.
Alexandre Ghiti [Mon, 17 Feb 2020 05:28:47 +0000 (00:28 -0500)]
riscv: Fix range looking for kernel image memblock
When looking for the memblock where the kernel lives, we should check
that the memory range associated to the memblock entirely comprises the
kernel image and not only intersects with it.
The reverted commit says "It's possible to release the node ID
immediately when fwnode_remove_software_node() is called, no need to
wait for software_node_release() with that." However, releasing the node
ID before waiting for software_node_release() to be called causes the
node ID to be released before the kobject and the underlying sysfs
entry; this means there is a period of time where a sysfs entry exists
that is associated with an unallocated node ID.
Once consequence of this is that there is a race condition where it is
possible to call fwnode_create_software_node() with no parent node
specified (NULL) and have it fail with -EEXIST because the node ID that
was assigned is still associated with a stale sysfs entry that hasn't
been cleaned up yet.
Although it is difficult to reproduce this race condition under normal
conditions, it can be deterministically reproduced with the following
minconfig on UML:
Running the tests with this configuration causes the following failure:
<snip>
kobject: 'node0' ((____ptrval____)): kobject_release, parent (____ptrval____) (delayed 400)
ok 1 - pe_test_uints
sysfs: cannot create duplicate filename '/kernel/software_nodes/node0'
CPU: 0 PID: 28 Comm: kunit_try_catch Not tainted 5.6.0-rc3-next-20200227 #14
<snip>
kobject_add_internal failed for node0 with -EEXIST, don't try to register things with the same name in the same directory.
kobject: 'node0' ((____ptrval____)): kobject_release, parent (____ptrval____) (delayed 100)
# pe_test_uint_arrays: ASSERTION FAILED at drivers/base/test/property-entry-test.c:123
Expected node is not error, but is: -17
not ok 2 - pe_test_uint_arrays
<snip>
Reported-by: Heidi Fahim <heidifahim@google.com> Signed-off-by: Brendan Higgins <brendanhiggins@google.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: 5.3+ <stable@vger.kernel.org> # 5.3+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds [Wed, 4 Mar 2020 19:02:45 +0000 (13:02 -0600)]
Merge tag 'for-5.6/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix request-based DM's congestion_fn and actually wire it up to the
bdi.
- Extend dm-bio-record to track additional struct bio members needed by
DM integrity target.
- Fix DM core to properly advertise that a device is suspended during
unload (between the presuspend and postsuspend hooks). This change is
a prereq for related DM integrity and DM writecache fixes. It
elevates DM integrity's 'suspending' state tracking to DM core.
- Four stable fixes for DM integrity target.
- Fix crash in DM cache target due to incorrect work item cancelling.
- Fix DM thin metadata lockdep warning that was introduced during 5.6
merge window.
- Fix DM zoned target's chunk work refcounting that regressed during
recent conversion to refcount_t.
- Bump the minor version for DM core and all target versions that have
seen interface changes or important fixes during the 5.6 cycle.
* tag 'for-5.6/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: bump version of core and various targets
dm: fix congested_fn for request-based device
dm integrity: use dm_bio_record and dm_bio_restore
dm bio record: save/restore bi_end_io and bi_integrity
dm zoned: Fix reference counter initial value of chunk works
dm writecache: verify watermark during resume
dm: report suspended device during destroy
dm thin metadata: fix lockdep complaint
dm cache: fix a crash due to incorrect work item cancelling
dm integrity: fix invalid table returned due to argument count mismatch
dm integrity: fix a deadlock due to offloading to an incorrect workqueue
dm integrity: fix recalculation when moving from journal mode to bitmap mode
Damien Le Moal [Wed, 12 Feb 2020 10:34:24 +0000 (19:34 +0900)]
riscv: Force flat memory model with no-mmu
Compilation errors trigger if ARCH_SPARSEMEM_ENABLE is enabled for
a nommu kernel. Since the sparsemem model does not make sense anyway
for the nommu case, do not allow selecting this option to always use
the flatmem model.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Anup Patel <anup@brainfault.org> Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Bernard Metzler [Mon, 2 Mar 2020 18:16:14 +0000 (19:16 +0100)]
RDMA/iwcm: Fix iwcm work deallocation
The dealloc_work_entries() function must update the work_free_list pointer
while freeing its entries, since potentially called again on same list. A
second iteration of the work list caused system crash. This happens, if
work allocation fails during cma_iw_listen() and free_cm_id() tries to
free the list again during cleanup.
Fixes: 922a8e9fb2e0 ("RDMA: iWARP Connection Manager.") Link: https://lore.kernel.org/r/20200302181614.17042-1-bmt@zurich.ibm.com Reported-by: syzbot+cb0c054eabfba4342146@syzkaller.appspotmail.com Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Reviewed-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Bernard Metzler [Mon, 2 Mar 2020 15:58:14 +0000 (16:58 +0100)]
RDMA/siw: Fix failure handling during device creation
A failing call to ib_device_set_netdev() during device creation caused
system crash due to xa_destroy of uninitialized xarray hit by device
deallocation. Fixed by moving xarray initialization before potential
device deallocation.
Fixes: bdcf26bf9b3a ("rdma/siw: network and RDMA core interface") Link: https://lore.kernel.org/r/20200302155814.9896-1-bmt@zurich.ibm.com Reported-by: syzbot+2e80962bedd9559fe0b3@syzkaller.appspotmail.com Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Jason Gunthorpe [Thu, 27 Feb 2020 11:41:18 +0000 (13:41 +0200)]
RDMA/odp: Ensure the mm is still alive before creating an implicit child
Registration of a mmu_notifier requires the caller to hold a mmget() on
the mm as registration is not permitted to race with exit_mmap(). There is
a BUG_ON inside the mmu_notifier to guard against this.
Normally creating a umem is done against current which implicitly holds
the mmget(), however an implicit ODP child is created from a pagefault
work queue and is not guaranteed to have a mmget().
Call mmget() around this registration and abort faulting if the MM has
gone to exit_mmap().
Before the patch below the notifier was registered when the implicit ODP
parent was created, so there was no chance to register a notifier outside
of current.
Fixes: c571feca2dc9 ("RDMA/odp: use mmu_notifier_get/put for 'struct ib_ucontext_per_mm'") Link: https://lore.kernel.org/r/20200227114118.94736-1-leon@kernel.org Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Maor Gottlieb [Thu, 27 Feb 2020 11:27:08 +0000 (13:27 +0200)]
RDMA/core: Fix protection fault in ib_mr_pool_destroy
Fix NULL pointer dereference in the error flow of ib_create_qp_user
when accessing to uninitialized list pointers - rdma_mrs and sig_mrs.
The following crash from syzkaller revealed it.
projects / linux-stable / log