The buffer size is 2 Bytes and we expect to receive the same amount of
data. But sometimes we receive less data and run into uninit-was-stored
issue upon read. Hence modify the error check on the return value to match
with the buffer size as a prevention.
Reported-and-tested by: syzbot+a7e220df5a81d1ab400e@syzkaller.appspotmail.com Signed-off-by: Himadri Pandya <himadrispandya@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
collapse_file() in khugepaged passes PAGE_SIZE as the number of pages to
be read to page_cache_sync_readahead(). The intent was probably to read
a single page. Fix it to use the number of pages to the end of the
window instead.
Fixes: 99cb0dbd47a1 ("mm,thp: add read-only THP support for (non-shmem) FS") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Acked-by: Song Liu <songliubraving@fb.com> Acked-by: Yang Shi <shy828301@gmail.com> Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com> Cc: Eric Biggers <ebiggers@google.com> Link: https://lkml.kernel.org/r/20200903140844.14194-2-willy@infradead.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between the assignment of `table->data` and write value
to the pointer of `table->data` in the __do_proc_doulongvec_minmax() on
the other thread.
Fix this by duplicating the `table`, and only update the duplicate of
it. And introduce a helper of proc_hugetlb_doulongvec_minmax() to
simplify the code.
Since commit cf11e85fc08c ("mm: hugetlb: optionally allocate gigantic
hugepages using cma"), the gigantic page would be allocated from node
which is not the preferred node, although there are pages available from
that node. The reason is that the nid parameter has been ignored in
alloc_gigantic_page().
Besides, the __GFP_THISNODE also need be checked if user required to
alloc only from the preferred node.
After this patch, the preferred node is tried first before other allowed
nodes, and don't try to allocate from other nodes if __GFP_THISNODE is
specified. If user don't specify the preferred node, the current node
will be used as preferred node, which makes sure consistent behavior of
allocating gigantic and non-gigantic hugetlb page.
Fixes: cf11e85fc08c ("mm: hugetlb: optionally allocate gigantic hugepages using cma") Signed-off-by: Li Xinhai <lixinhai.lxh@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Roman Gushchin <guro@fb.com> Link: https://lkml.kernel.org/r/20200902025016.697260-1-lixinhai.lxh@gmail.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f45ec5ff16a75 ("userfaultfd: wp: support swap and page migration")
introduced support for tracking the uffd wp bit during page migration.
However the non-swap PTE variant was used to set the flag for zone device
private pages which are a type of swap page.
This leads to corruption of the swap offset if the original PTE has the
uffd_wp flag set.
Fixes: f45ec5ff16a75 ("userfaultfd: wp: support swap and page migration") Signed-off-by: Alistair Popple <alistair@popple.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Jérôme Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Link: https://lkml.kernel.org/r/20200825064232.10023-1-alistair@popple.id.au Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usage of "capture group (...)" in the immediate condition after `&&`
results in `$1` being uninitialized. This issues a warning "Use of
uninitialized value $1 in regexp compilation at ./scripts/checkpatch.pl
line 2638".
I noticed this bug while running checkpatch on the set of commits from
v5.7 to v5.8-rc1 of the kernel on the commits with a diff content in
their commit message.
This bug was introduced in the script by commit e518e9a59ec3
("checkpatch: emit an error when there's a diff in a changelog"). It
has been in the script since then.
The author intended to store the match made by capture group in variable
`$1`. This should have contained the name of the file as `[\w/]+`
matched. However, this couldn't be accomplished due to usage of capture
group and `$1` in the same regular expression.
Fix this by placing the capture group in the condition before `&&`.
Thus, `$1` can be initialized to the text that capture group matches
thereby setting it to the desired and required value.
Fixes: e518e9a59ec3 ("checkpatch: emit an error when there's a diff in a changelog") Signed-off-by: Mrinal Pandey <mrinalmni@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Tested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Reviewed-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Cc: Joe Perches <joe@perches.com> Link: https://lkml.kernel.org/r/20200714032352.f476hanaj2dlmiot@mrinalpandey Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra210 and later has a separate sdmmc_legacy_tm (TMCLK) used by Tegra
SDMMC hawdware for data timeout to achive better timeout than using
SDCLK and using TMCLK is recommended.
USE_TMCLK_FOR_DATA_TIMEOUT bit in Tegra SDMMC register
SDHCI_TEGRA_VENDOR_SYS_SW_CTRL can be used to choose either TMCLK or
SDCLK for data timeout.
Default USE_TMCLK_FOR_DATA_TIMEOUT bit is set to 1 and TMCLK is used
for data timeout by Tegra SDMMC hardware and having TMCLK not enabled
is not recommended.
So, this patch adds quirk NVQUIRK_HAS_TMCLK for SoC having separate
timeout clock and keeps TMCLK enabled all the time.
The help info of option "--no-bpf-event" is wrongly described as "record
bpf events", correct it.
Committer testing:
$ perf record -h bpf
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
--clang-opt <clang options>
options passed to clang when compiling BPF scriptlets
--clang-path <clang path>
clang binary to use for compiling BPF scriptlets
--no-bpf-event do not record bpf events
$
Fixes: 71184c6ab7e6 ("perf record: Replace option --bpf-event with --no-bpf-event") Signed-off-by: Wei Li <liwei391@huawei.com> Acked-by: Song Liu <songliubraving@fb.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Hanjun Guo <guohanjun@huawei.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Li Bin <huawei.libin@huawei.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: http://lore.kernel.org/lkml/20200819031947.12115-1-liwei391@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During memory migration a pte is temporarily replaced with a migration
swap pte. Some pte bits from the existing mapping such as the soft-dirty
and uffd write-protect bits are preserved by copying these to the
temporary migration swap pte.
However these bits are not stored at the same location for swap and
non-swap ptes. Therefore testing these bits requires using the
appropriate helper function for the given pte type.
Unfortunately several code locations were found where the wrong helper
function is being used to test soft_dirty and uffd_wp bits which leads to
them getting incorrectly set or cleared during page-migration.
Fix these by using the correct tests based on pte type.
Fixes: a5430dda8a3a ("mm/migrate: support un-addressable ZONE_DEVICE page in migration") Fixes: 8c3328f1f36a ("mm/migrate: migrate_vma() unmap page from vma while collecting pages") Fixes: f45ec5ff16a7 ("userfaultfd: wp: support swap and page migration") Signed-off-by: Alistair Popple <alistair@popple.id.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Jérôme Glisse <jglisse@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Alistair Popple <alistair@popple.id.au> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20200825064232.10023-2-alistair@popple.id.au Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: use-after-free in madvise_willneed mm/madvise.c:293 [inline]
BUG: KASAN: use-after-free in madvise_vma mm/madvise.c:942 [inline]
BUG: KASAN: use-after-free in do_madvise.part.0+0x1c8b/0x1cf0 mm/madvise.c:1145
Read of size 8 at addr ffff8880a6163eb0 by task syz-executor.0/9996
__apply_to_page_range() is also used to change and/or allocate
page-table pages in the vmalloc area of the address space. Make sure
these changes get synchronized to other page-tables in the system by
calling arch_sync_kernel_mappings() when necessary.
The impact appears limited to x86-32, where apply_to_page_range may miss
updating the PMD. That leads to explosions in drivers like
Commit 52f23478081ae0 ("mm/slub.c: fix corrupted freechain in
deactivate_slab()") suffered an update when picked up from LKML [1].
Specifically, relocating 'freelist = NULL' into 'freelist_corrupted()'
created a no-op statement. Fix it by sticking to the behavior intended
in the original patch [1]. In addition, make freelist_corrupted()
immune to passing NULL instead of &freelist.
The issue has been spotted via static analysis and code review.
The following error ocurred when testing disk online/offline:
[ 301.798344] device-mapper: thin: 253:5: aborting current metadata transaction
[ 301.848441] device-mapper: thin: 253:5: failed to abort metadata transaction
[ 301.849206] Aborting journal on device dm-26-8.
[ 301.850489] EXT4-fs error (device dm-26) in __ext4_new_inode:943: Journal has aborted
[ 301.851095] EXT4-fs (dm-26): Delayed block allocation failed for inode 398742 at logical offset 181 with max blocks 19 with error 30
[ 301.854476] BUG: KASAN: use-after-free in dm_bm_set_read_only+0x3a/0x40 [dm_persistent_data]
Reason is:
metadata_operation_failed
abort_transaction
dm_pool_abort_metadata
__create_persistent_data_objects
r = __open_or_format_metadata
if (r) --> If failed will free pmd->bm but pmd->bm not set NULL
dm_block_manager_destroy(pmd->bm);
set_pool_mode
dm_pool_metadata_read_only(pool->pmd);
dm_bm_set_read_only(pmd->bm); --> use-after-free
Add checks to see if pmd->bm is NULL in dm_bm_set_read_only and
dm_bm_set_read_write functions. If bm is NULL it means creating the
bm failed and so dm_bm_is_read_only must return true.
Signed-off-by: Ye Bin <yebin10@huawei.com> Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maybe __create_persistent_data_objects() caller will use PTR_ERR as a
pointer, it will lead to some strange things.
Signed-off-by: Ye Bin <yebin10@huawei.com> Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maybe __create_persistent_data_objects() caller will use PTR_ERR as a
pointer, it will lead to some strange things.
Signed-off-by: Ye Bin <yebin10@huawei.com> Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dm-integrity target did not report errors in bitmap mode just after
creation. The reason is that the function integrity_recalc didn't clean up
ic->recalc_bitmap as it proceeded with recalculation.
Fix this by updating the bitmap accordingly -- the double shift serves
to rounddown.
Commit 935fcc56abc3 ("dm mpath: only flush workqueue when needed")
changed flush_multipath_work() to avoid needless workqueue
flushing (of a multipath global workqueue). But that change didn't
realize the surrounding flush_multipath_work() code should also only
run if 'pg_init_in_progress' is set.
Fix this by only doing all of flush_multipath_work()'s PG init related
work if 'pg_init_in_progress' is set.
Otherwise multipath_wait_for_pg_init_completion() will run
unconditionally but the preceeding flush_workqueue(kmpath_handlerd)
may not. This could lead to deadlock (though only if kmpath_handlerd
never runs a corresponding work to decrement 'pg_init_in_progress').
It could also be, though highly unlikely, that the kmpath_handlerd
work that does PG init completes before 'pg_init_in_progress' is set,
and then an intervening DM table reload's multipath_postsuspend()
triggers flush_multipath_work().
Fixes: 935fcc56abc3 ("dm mpath: only flush workqueue when needed") Cc: stable@vger.kernel.org Reported-by: Ben Marzinski <bmarzins@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function dax_direct_access doesn't take partitions into account,
it always maps pages from the beginning of the device. Therefore,
persistent_memory_claim() must get the partition offset using
get_start_sect() and add it to the page offsets passed to
dax_direct_access().
Starting in Linux 5.8, the graphics and memory clock frequency were not being
reported for CIK cards. This is a regression, since they were reported correctly
in Linux 5.7.
After investigation, I discovered that the smum_send_msg_to_smc() function,
attempts to call the corresponding get_argument() function of ci_smu_funcs.
However, the get_argument() function is not defined in ci_smu_funcs.
This patch fixes the bug by specifying the correct get_argument() function.
Fixes: a0ec225633d9f6 ("drm/amd/powerplay: unified interfaces for message issuing and response checking") Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normally softwareshutdowntemp should be greater than Thotspotlimit.
However, on some VEGA10 ASIC, the softwareshutdowntemp is 91C while
Thotspotlimit is 105C. This seems not right and may trigger some
false alarms.
Signed-off-by: Evan Quan <evan.quan@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1- We weren't taking into account sha_leftovers when adding multiple
ksvs to sha_text. As such, we were or'ing the end of ksv[j - 1] with
the beginning of ksv[j]
2- In the sha_leftovers == 2 and sha_leftovers == 3 case, bstatus was
being placed on the wrong half of sha_text, overlapping the leftover
ksv value
3- In the sha_leftovers == 2 case, we need to manually terminate the
byte stream with 0x80 since the hardware doesn't have enough room to
add it after writing M0
The upside is that all of the HDCP supported HDMI repeaters I could
find on Amazon just strip HDCP anyways, so it turns out to be _really_
hard to hit any of these cases without an MST hub, which is not (yet)
supported. Oh, and the sha_leftovers == 1 case works perfectly!
Fixes: ee5e5e7a5e0f ("drm/i915: Add HDCP framework + base implementation") Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ramalingam C <ramalingam.c@intel.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Cc: Jani Nikula <jani.nikula@linux.intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: intel-gfx@lists.freedesktop.org Cc: <stable@vger.kernel.org> # v4.17+ Reviewed-by: Ramalingam C <ramalingam.c@intel.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Signed-off-by: Ramalingam C <ramalingam.c@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-2-sean@poorly.run
(cherry picked from commit 1f0882214fd0037b74f245d9be75c31516fed040) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the source and destination physical address calculation of a
peripheral device on scatter-gather implementation.
This issue manifested during tests using a 64 bits architecture system.
The abnormal behavior wasn't visible before due to all previous tests
were done using 32 bits architecture system, that masked his effect.
blk-iocost calls blk_stat_enable_accounting() while holding an irqsafe lock
which triggers a lockdep splat because q->stats->lock isn't irqsafe. Let's
make it irqsafe.
ioc_pd_free() grabs irq-safe ioc->lock without ensuring that irq is disabled
when it can be called with irq disabled or enabled. This has a small chance
of causing A-A deadlocks and triggers lockdep splats. Use irqsave operations
instead.
We want neither
"
include/linux/compiler_attributes.h:201:41: warning: statement will never
be executed [-Wswitch-unreachable]
201 | # define fallthrough __attribute__((__fallthrough__))
| ^~~~~~~~~~~~~
"
nor
"
include/linux/compiler_attributes.h:201:41: warning: attribute
'fallthrough' not preceding a case label or default label
201 | # define fallthrough __attribute__((__fallthrough__))
| ^~~~~~~~~~~~~
"
It's not worth adding one more macro. Let's simply place the fallthrough
in between the expansions.
Fixes: c9b029903466 ("MIPS: Use fallthrough for arch/mips") Cc: stable@vger.kernel.org Signed-off-by: He Zhe <zhe.he@windriver.com> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All three generations of Sandisk SSDs lock up hard intermittently.
Experiments showed that disabling NCQ lowered the failure rate significantly
and the kernel has been disabling NCQ for some models of SD7's and 8's,
which is obviously undesirable.
Karthik worked with Sandisk to root cause the hard lockups to trim commands
larger than 128M. This patch implements ATA_HORKAGE_MAX_TRIM_128M which
limits max trim size to 128M and applies it to all three generations of
Sandisk SSDs.
Commit fa686453053b ("sched/rt, s390: Use CONFIG_PREEMPTION")
changed a bunch of uses of CONFIG_PREEMPT to _PREEMPTION.
Except in the Kconfig it used two T's. That's the only place
in the system where that spelling exists, so let's fix that.
Index here is already the position of the file in fixed_file_table, we
should not use io_file_from_index() again to get it. Otherwise, the
wrong file which still in use may be released unexpectedly.
Cc: stable@vger.kernel.org # v5.6 Fixes: 05f3fb3c5397 ("io_uring: avoid ring quiesce for fixed file set unregister and update") Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While io_sqe_file_register() failed in __io_sqe_files_update(),
table->files[i] still point to the original file which may freed
soon, and that will trigger use-after-free problems.
If a driver leaves the limit settings as the defaults, then we don't
initialize bdi->io_pages. This means that file systems may need to
work around bdi->io_pages == 0, which is somewhat messy.
Initialize the default value just like we do for ->ra_pages.
Cc: stable@vger.kernel.org Fixes: 9491ae4aade6 ("mm: don't cap request size based on read-ahead setting") Reported-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Block layer usually doesn't support or allow zero-length bvec. Since
commit 1bdc76aea115 ("iov_iter: use bvec iterator to implement
iterate_bvec()"), iterate_bvec() switches to bvec iterator. However,
Al mentioned that 'Zero-length segments are not disallowed' in iov_iter.
Fixes for_each_bvec() so that it can move on after seeing one zero
length bvec.
Fixes: 1bdc76aea115 ("iov_iter: use bvec iterator to implement iterate_bvec()") Reported-by: syzbot <syzbot+61acc40a49a3e46e25ea@syzkaller.appspotmail.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Link: https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg2262077.html Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The basic permission bits (protection bits in AmigaOS) have been broken
in Linux' AFFS - it would only set bits, but never delete them.
Also, contrary to the documentation, the Archived bit was not handled.
Let's fix this for good, and set the bits such that Linux and classic
AmigaOS can coexist in the most peaceful manner.
Also, update the documentation to represent the current state of things.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Signed-off-by: Max Staudt <max@enpas.org> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device drivers do not expect to have change_protocol or wakeup
re-programming to be accesed after rc_unregister_device(). This can
cause the device driver to access deallocated resources.
Cc: <stable@vger.kernel.org> # 4.16+ Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Intel controllers, SDHCI_RESET_ALL resets also CQHCI registers.
Normally, SDHCI_RESET_ALL is not used while CQHCI is enabled, but that can
happen on the error path. e.g. if mmc_cqe_recovery() fails, mmc_blk_reset()
is called which, for a eMMC that does not support HW Reset, will cycle the
bus power and the driver will perform SDHCI_RESET_ALL.
So whenever performing SDHCI_RESET_ALL ensure CQHCI is deactivated.
That will force the driver to reinitialize CQHCI when it is next used.
A similar change was done already for sdhci-msm, and other drivers using
CQHCI might benefit from a similar change, if they also have CQHCI reset
by SDHCI_RESET_ALL.
This patch fixs eMMC-Access on mt7622/Bpi-64.
Before we got these Errors on mounting eMMC ion R64:
[ 48.664925] blk_update_request: I/O error, dev mmcblk0, sector 204800 op 0x1:(WRITE)
flags 0x800 phys_seg 1 prio class 0
[ 48.676019] Buffer I/O error on dev mmcblk0p1, logical block 0, lost sync page write
This patch adds a optional reset management for msdc.
Sometimes the bootloader does not bring msdc register
to default state, so need reset the msdc controller.
Cc: <stable@vger.kernel.org> # v5.4+ Fixes: 966580ad236e ("mmc: mediatek: add support for MT7622 SoC") Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Tested-by: Frank Wunderlich <frank-w@public-files.de> Link: https://lore.kernel.org/r/20200814014346.6496-4-wenbin.mei@mediatek.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There've been quite a few regression reports about the lowered volume
(reduced to ca 65% from the previous level) on Lenovo Thinkpad X1
after the commit d2cd795c4ece ("ALSA: hda - fixup for the bass speaker
on Lenovo Carbon X1 7th gen"). Although the commit itself does the
right thing from HD-audio POV in order to have a volume control for
bass speakers, it seems that the machine has some secret recipe under
the hood.
Through experiments, Benjamin Poirier found out that the following
routing gives the best result:
* DAC1 (NID 0x02) -> Speaker pin (NID 0x14)
* DAC2 (NID 0x03) -> Shared by both Bass Speaker pin (NID 0x17) &
Headphone pin (0x21)
* DAC3 (NID 0x06) -> Unused
DAC1 seems to have some equalizer internally applied, and you'd get
again the output in a bad quality if you connect this to the
headphone pin. Hence the headphone is connected to DAC2, which is now
shared with the bass speaker pin. DAC3 has no volume amp, hence it's
not connected at all.
For achieving the routing above, this patch introduced a couple of
workarounds:
* The connection list of bass speaker pin (NID 0x17) is reduced not to
include DAC3 (NID 0x06)
* Pass preferred_pairs array to specify the fixed connection
Here, both workarounds are needed because the generic parser prefers
the individual DAC assignment over others.
When the routing above is applied, the generic parser creates the two
volume controls "Front" and "Bass Speaker". Since we have only two
DACs for three output pins, those are not fully controlling each
output individually, and it would confuse PulseAudio. For avoiding
the pitfall, in this patch, we rename those volume controls to some
unique ones ("DAC1" and "DAC2"). Then PulseAudio ignore them and
concentrate only on the still good-working "Master" volume control.
If a user still wants to control each DAC volume, they can still
change manually via "DAC1" and "DAC2" volume controls.
The Galaxy Book Ion NT950XCJ-X716A (15 inches) uses the same ALC298
codec as other Samsung laptops which have the no headphone sound bug. I
confirmed on my own hardware that this fixes the bug.
This also correct the model name for the 13 inches version. It was
incorrectly referenced as NT950XCJ-X716A in commit e17f02d05. But it
should have been NP930XCJ-K01US.
Tascam FE-8 is known to support communication by asynchronous transaction
only. The support can be implemented in userspace application and
snd-firewire-ctl-services project has the support. However, ALSA
firewire-tascam driver is bound to the model.
This commit changes device entries so that the model is excluded. In a
commit 53b3ffee7885 ("ALSA: firewire-tascam: change device probing
processing"), I addressed to the concern that version field in
configuration differs depending on installed firmware. However, as long
as I checked, the version number is fixed. It's safe to return version
number back to modalias.
Following Christian Lachner's patch for Gigabyte X570-based motherboards,
also patch the MSI X570-A PRO motherboard; the ALC1220 codec requires the
same workaround for Clevo laptops to enforce the DAC/mixer connection
path. Set up a quirk entry for that.
I suspect most if all X570 motherboards will require similar patches.
[ The entries reordered in the SSID order -- tiwai ]
Avid Adrenaline is reported that ALSA firewire-digi00x driver is bound to.
However, as long as he investigated, the design of this model is hardly
similar to the one of Digi 00x family. It's better to exclude the model
from modalias of ALSA firewire-digi00x driver.
This commit changes device entries so that the model is excluded.
When system is suspended with active audio playback to HDMI/DP, two
alternative sequences can happen at resume:
a) monitor is detected first and ALSA prepare follows normal
stream setup sequence, or
b) ALSA prepare is called first, but monitor is not yet detected,
so PCM is restarted without a pin,
In case of (b), on i915 systems, haswell_verify_D0() is not called at
resume and the pin power state may be incorrect. Result is lack of audio
after resume with no error reported back to user-space.
Fix the problem by always verifying converter and pin state in the
i915_pin_cvt_fixup().
The PCM OSS mulaw plugin has a check of the format of the counter part
whether it's a linear format. The check is with snd_BUG_ON() that
emits WARN_ON() when the debug config is set, and it confuses
syzkaller as if it were a serious issue. Let's drop snd_BUG_ON() for
avoiding that.
While we're at it, correct the error code to a more suitable, EINVAL.
snd_ca0106_spi_write() returns 1 on error, snd_ca0106_pcm_power_dac()
is returning the error code directly, and the caller is expecting an
negative error code
Because AZX_DRIVER_GENERIC can not work well for Loongson LS7A HDA
controller, it needs some workarounds which are not merged into the
upstream kernel at this time, so it should revert this patch now.
Fixes: 61eee4a7fc40 ("ALSA: hda: Add support for Loongson 7A1000 controller") Cc: <stable@vger.kernel.org> # 5.9-rc1+ Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Link: https://lore.kernel.org/r/1598348388-2518-1-git-send-email-yangtiezhu@loongson.cn Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
removed it on x86 alltogether because previously the
arch_sync_kernel_mappings() interface was introduced. This interface
added synchronization of vmalloc/ioremap page-table updates to all
page-tables in the system at creation time and was thought to make
vmalloc faulting obsolete.
But that assumption was incredibly naive.
It turned out that there is a race window between the time the vmalloc
or ioremap code establishes a mapping and the time it synchronizes
this change to other page-tables in the system.
During this race window another CPU or thread can establish a vmalloc
mapping which uses the same intermediate page-table entries (e.g. PMD
or PUD) and does no synchronization in the end, because it found all
necessary mappings already present in the kernel reference page-table.
But when these intermediate page-table entries are not yet
synchronized, the other CPU or thread will continue with a vmalloc
address that is not yet mapped in the page-table it currently uses,
causing an unhandled page fault and oops like below:
So the arch_sync_kernel_mappings() interface is racy, but removing it
would mean to re-introduce the vmalloc_sync_all() interface, which is
even more awful. Keep arch_sync_kernel_mappings() in place and catch
the race condition in the page-fault handler instead.
Do a partial revert of above commit to get vmalloc faulting on x86-32
back in place.
The original return is NOTIFY_STOP, but notifier_call_chain would stop
the future call for register_pm_notifier even registered on other Kernel
modules with the same priority which value is zero.
[BUG]
After commit 9afc66498a0b ("btrfs: block-group: refactor how we read one
block group item"), cache->length is being assigned after calling
btrfs_create_block_group_cache. This causes a problem since
set_free_space_tree_thresholds calculates the free-space threshold to
decide if the free-space tree should convert from extents to bitmaps.
The current code calls set_free_space_tree_thresholds with cache->length
being 0, which then makes cache->bitmap_high_thresh zero. This implies
the system will always use bitmap instead of extents, which is not
desired if the block group is not fragmented.
This behavior can be seen by a test that expects to repair systems
with FREE_SPACE_EXTENT and FREE_SPACE_BITMAP, but the current code only
created FREE_SPACE_BITMAP.
[FIX]
Call set_free_space_tree_thresholds after setting cache->length. There
is now a WARN_ON in set_free_space_tree_thresholds to help preventing
the same mistake to happen again in the future.
Link: https://github.com/kdave/btrfs-progs/issues/251 Fixes: 9afc66498a0b ("btrfs: block-group: refactor how we read one block group item") CC: stable@vger.kernel.org # 5.8+ Reviewed-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are special extent buffers that get rewound in order to lookup
the state of the tree at a specific point in time. As such they do not
go through the normal initialization paths that set their lockdep class,
so handle them appropriately when they are created and before they are
locked.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When flipping over to the rw_semaphore I noticed I'd get a lockdep splat
in replace_path(), which is weird because we're swapping the reloc root
with the actual target root. Turns out this is because we're using the
root->root_key.objectid as the root id for the newly allocated tree
block when setting the lockdep class, however we need to be using the
actual owner of this new block, which is saved in owner.
The affected path is through btrfs_copy_root as all other callers of
btrfs_alloc_tree_block (which calls init_new_buffer) have root_objectid
== root->root_key.objectid .
CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens because we're allocating the scrub workqueues under the
scrub and device list mutex, which brings in a whole host of other
dependencies.
Because the work queue allocation is done with GFP_KERNEL, it can
trigger reclaim, which can lead to a transaction commit, which in turns
needs the device_list_mutex, it can lead to a deadlock. A different
problem for which this fix is a solution.
Fix this by moving the actual allocation outside of the
scrub lock, and then only take the lock once we're ready to actually
assign them to the fs_info. We'll now have to cleanup the workqueues in
a few more places, so I've added a helper to do the refcount dance to
safely free the workqueues.
CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is we're doing a copy_to_user() while holding tree locks,
which can deadlock if we have to do a page fault for the copy_to_user().
This exists even without my locking changes, so it needs to be fixed.
Rework the search ioctl to do the pre-fault and then
copy_to_user_nofault for the copying.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This problem exists because we have two different rescan threads,
btrfs_uuid_scan_kthread which creates the uuid tree, and
btrfs_uuid_tree_iterate that goes through and updates or deletes any out
of date roots. The problem is they both do things in different order.
btrfs_uuid_scan_kthread() reads the tree_root, and then inserts entries
into the uuid_root. btrfs_uuid_tree_iterate() scans the uuid_root, but
then does a btrfs_get_fs_root() which can read from the tree_root.
It's actually easy enough to not be holding the path in
btrfs_uuid_scan_kthread() when we add a uuid entry, as we already drop
it further down and re-start the search when we loop. So simply move
the path release before we add our entry to the uuid tree.
This also fixes a problem where we're holding a path open after we do
btrfs_end_transaction(), which has it's own problems.
CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework of memory map initialization broke initialization of ARC systems
with two memory banks. Before these changes, memblock was not aware of
nodes configuration and the memory map was always allocated from the
"lowmem" bank. After the addition of node information to memblock, the core
mm attempts to allocate the memory map for the "highmem" bank from its
node. The access to this memory using __va() fails because it can be only
accessed using kmap.
Anther problem that was uncovered is that {min,max}_high_pfn are calculated
from u64 high_mem_start variable which prevents truncation to 32-bit
physical address and the PFN values are above the node and zone boundaries.
Use phys_addr_t type for high_mem_start and high_mem_size to ensure
correspondence between PFNs and highmem zone boundaries and reserve the
entire highmem bank until mem_init() to avoid accesses to it before highmem
is enabled.
To test this:
1. Enable HIGHMEM in ARC config
2. Enable 2 memory banks in haps_hs.dts (uncomment the 2nd bank)
Fixes: 51930df5801e ("mm: free_area_init: allow defining max_zone_pfn in descending order") Cc: stable@vger.kernel.org [5.8] Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: added instructions to test highmem] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running in a dax mode, if the user maps a page with MAP_PRIVATE and
PROT_WRITE, the xfs filesystem would incorrectly update ctime and mtime
when the user hits a COW fault.
This breaks building of the Linux kernel. How to reproduce:
1. extract the Linux kernel tree on dax-mounted xfs filesystem
2. run make clean
3. run make -j12
4. run make -j12
at step 4, make would incorrectly rebuild the whole kernel (although it
was already built in step 3).
The reason for the breakage is that almost all object files depend on
objtool. When we run objtool, it takes COW page fault on its .data
section, and these faults will incorrectly update the timestamp of the
objtool binary. The updated timestamp causes make to rebuild the whole
tree.
When running in a dax mode, if the user maps a page with MAP_PRIVATE and
PROT_WRITE, the ext2 filesystem would incorrectly update ctime and mtime
when the user hits a COW fault.
This breaks building of the Linux kernel. How to reproduce:
1. extract the Linux kernel tree on dax-mounted ext2 filesystem
2. run make clean
3. run make -j12
4. run make -j12
at step 4, make would incorrectly rebuild the whole kernel (although it
was already built in step 3).
The reason for the breakage is that almost all object files depend on
objtool. When we run objtool, it takes COW page fault on its .data
section, and these faults will incorrectly update the timestamp of the
objtool binary. The updated timestamp causes make to rebuild the whole
tree.
Trying to clear DR7 around a #DB from usermode malfunctions if the tasks
schedules when delivering SIGTRAP.
Rather than trying to define a special no-recursion region, just allow a
single level of recursion. The same mechanism is used for NMI, and it
hasn't caused any problems yet.
The WARN added in commit 3c73b81a9164 ("x86/entry, selftests: Further
improve user entry sanity checks") unconditionally triggers on a IVB
machine because it does not support SMAP.
For !SMAP hardware the CLAC/STAC instructions are patched out and thus if
userspace sets AC, it is still have set after entry.
Fixes: 3c73b81a9164 ("x86/entry, selftests: Further improve user entry sanity checks") Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Daniel Thompson <daniel.thompson@linaro.org> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200902133200.666781610@infradead.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Beware that the address size for x86-32 may exceed unsigned long.
[ 0.368971] UBSAN: shift-out-of-bounds in drivers/iommu/intel/iommu.c:128:14
[ 0.369055] shift exponent 36 is too large for 32-bit type 'long unsigned int'
If we don't handle the wide addresses, the pages are mismapped and the
device read/writes go astray, detected as DMAR faults and leading to
device failure. The behaviour changed (from working to broken) in commit fa954e683178 ("iommu/vt-d: Delegate the dma domain to upper layer"), but
the error looks older.
Fixes: fa954e683178 ("iommu/vt-d: Delegate the dma domain to upper layer") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Lu Baolu <baolu.lu@linux.intel.com> Cc: James Sewart <jamessewart@arista.com> Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: Joerg Roedel <jroedel@suse.de> Cc: <stable@vger.kernel.org> # v5.3+ Link: https://lore.kernel.org/r/20200822160209.28512-1-chris@chris-wilson.co.uk Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise gcc generates warnings if the expression is complicated.
Fixes: 312a0c170945 ("[PATCH] LOG2: Alter roundup_pow_of_two() so that it can use a ilog2() on a constant") Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Link: https://lkml.kernel.org/r/0-v1-8a2697e3c003+41165-log_brackets_jgg@nvidia.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using tp_reserve to calculate netoff can overflow as
tp_reserve is unsigned int and netoff is unsigned short.
This may lead to macoff receving a smaller value then
sizeof(struct virtio_net_hdr), and if po->has_vnet_hdr
is set, an out-of-bounds write will occur when
calling virtio_net_hdr_from_skb.
The bug is fixed by converting netoff to unsigned int
and checking if it exceeds USHRT_MAX.
When using 128-bit interrupt-remapping table entry (IRTE) (a.k.a GA mode),
current driver disables interrupt remapping when it updates the IRTE
so that the upper and lower 64-bit values can be updated safely.
However, this creates a small window, where the interrupt could
arrive and result in IO_PAGE_FAULT (for interrupt) as shown below.
This scenario has been observed when changing irq affinity on a system
running I/O-intensive workload, in which the destination APIC ID
in the IRTE is updated.
Instead, use cmpxchg_double() to update the 128-bit IRTE at once without
disabling the interrupt remapping. However, this means several features,
which require GA (128-bit IRTE) support will also be affected if cmpxchg16b
is not supported (which is unprecedented for AMD processors w/ IOMMU).
Currently driver is suppressing the negative temperature
readings from the vadc. Consumers of the thermal zones need
to read the negative temperature too. Don't suppress the
readings.
Fixes: c610afaa21d3c6e ("thermal: Add QPNP PMIC temperature alarm driver") Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org> Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org> Reviewed-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/944856eb819081268fab783236a916257de120e4.1596040416.git.gurus@codeaurora.org Signed-off-by: Sasha Levin <sashal@kernel.org>
We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:
thermal thermal_zone0: critical temperature reached (143 C), shutting down
Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.
Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.
Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.
Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.
Fixes: 1a31270e54d7 ("staging: omap-thermal: add OMAP4 data structures") Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The VT-d spec requires (10.4.4 Global Command Register, GCMD_REG General
Description) that:
If multiple control fields in this register need to be modified, software
must serialize the modifications through multiple writes to this register.
However, in irq_remapping.c, modifications of IRE and CFI are done in one
write. We need to do two separate writes with STS checking after each. It
also checks the status register before writing command register to avoid
unnecessary register write.
Fixes: af8d102f999a4 ("x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess") Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: Kevin Tian <kevin.tian@intel.com> Cc: Ashok Raj <ashok.raj@intel.com> Link: https://lore.kernel.org/r/20200828000615.8281-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled. A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.
Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails. tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails. We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task(). Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: David Christensen <drc@linux.vnet.ibm.com> Reported-by: Baptiste Covolato <baptiste@arista.com> Fixes: db2199737990 ("tg3: Schedule at most one tg3_reset_task run") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function perf_session__new() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR()
Committer notes:
This wasn't compiling due to an extraneous '{' not matched by a '}', fix
it.
Fixes: 13edc237200c ("perf bench: Add a multi-threaded synthesize benchmark") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20200902140526.26916-1-yuehaibing@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The realtime flag only applies to the data fork, so don't use the
realtime block number checks on the attr fork of a realtime file.
Fixes: 30b0984d9117 ("xfs: refactor bmap record validation") Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On RM400(a20r) machines ISA and SCSI interrupts share the same interrupt
line. Commit 49e6e07e3c80 ("MIPS: pass non-NULL dev_id on shared
request_irq()") accidently dropped the IRQF_SHARED bit, which breaks
registering SCSI interrupt. Put back IRQF_SHARED and add dev_id for
ISA interrupt.
Fixes: 49e6e07e3c80 ("MIPS: pass non-NULL dev_id on shared request_irq()") Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In cc97ab235f3f ("MIPS: Simplify FP context initialization), init_fp_ctx
just initialize the fp/msa context, and own_fp_inatomic just restore
FCSR and 64bit FP regs from it, but miss MSACSR and upper MSA regs for
MSA, so MSACSR and MSA upper regs's value from previous task on current
cpu can leak into current task and cause unpredictable behavior when MSA
context not initialized.
Fix the registers being written to as the values were being over written
when writing the same registers.
Fixes: caabee5b53f5 ("net: phy: dp83867: support Wake on LAN") Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix an issue where the driver wrongly detected ipv6 neighbour updates
from the NFP as corrupt. Add a reserved field on the kernel side so
it is similar to the ipv4 version of the struct and has space for the
extra bytes from the card.
Fixes: 9ea9bfa12240 ("nfp: flower: support ipv6 tunnel keep-alive messages from fw") Signed-off-by: Louis Peens <louis.peens@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We recently added some calls to clk_disable_unprepare() but we missed
the last error path if register_netdev() fails.
I made a couple cleanups so we avoid mistakes like this in the future.
First I reversed the "if (!ret)" condition and pulled the code in one
indent level. Also, the "port->netdev = NULL;" is not required because
"port" isn't used again outside this function so I deleted that line.
Fixes: 4d5ae32f5e1e ("net: ethernet: Add a driver for Gemini gigabit ethernet") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
epoll_loop_check_proc() can run into a file already committed to destruction;
we can't grab a reference on those and don't need to add them to the set for
reverse path check anyway.
Tested-by: Marc Zyngier <maz@kernel.org> Fixes: a9ed4a6560b8 ("epoll: Keep a reference on files added to the check list") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
On machines with much memory (> 2 TByte) and log_mtts_per_seg == 0, a
max_order of 31 will be passed to mlx_buddy_init(), which results in
s = BITS_TO_LONGS(1 << 31) becoming a negative value, leading to
kvmalloc_array() failure when it is converted to size_t.
mlx4_core 0000:b1:00.0: Failed to initialize memory region table, aborting
mlx4_core: probe of 0000:b1:00.0 failed with error -12
Fix this issue by changing the left shifting operand from a signed literal to
an unsigned one.
Fixes: 225c7b1feef1 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters") Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
perf_event.h has macros that define the field offsets in the data_src
bitmask in perf records. The SNOOPX and REMOTE offsets were both 37.
These are distinct fields, and the bitfield layout in perf_mem_data_src
confirms that SNOOPX should be at offset 38.
Committer notes:
This was extracted from a larger patch that also contained kernel
changes.
Fixes: 52839e653b5629bd ("perf tools: Add support for printing new mem_info encodings") Signed-off-by: Al Grant <al.grant@arm.com> Reviewed-by: Andi Kleen <ak@linux.intel.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/9974f2d0-bf7f-518e-d9f7-4520e5ff1bb0@foss.arm.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack")
changed the format of branch stacks in perf samples. When samples use
this new format, a flag must be set in the corresponding event.
Synthesized branch stacks generated from Intel PT were using the new
format, but not setting the event attribute, leading to consumers
seeing corrupt data. This patch fixes the issue by setting the event
attribute to indicate use of the new format.
Fixes: 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") Signed-off-by: Al Grant <al.grant@arm.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Leo Yan <leo.yan@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mike Leach <mike.leach@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Link: http://lore.kernel.org/lkml/20200819084751.17686-2-leo.yan@linaro.org Signed-off-by: Leo Yan <leo.yan@linaro.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack")
changed the format of branch stacks in perf samples. When samples use
this new format, a flag must be set in the corresponding event.
Synthesized branch stacks generated from CoreSight ETM trace were using
the new format, but not setting the event attribute, leading to
consumers seeing corrupt data. This patch fixes the issue by setting the
event attribute to indicate use of the new format.
Fixes: 42bbabed09ce6208 ("perf tools: Add hw_idx in struct branch_stack") Signed-off-by: Al Grant <al.grant@arm.com> Reviewed-by: Andrea Brunato <andrea.brunato@arm.com> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Suzuki Poulouse <suzuki.poulose@arm.com> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Leo Yan <leo.yan@linaro.org> Link: http://lore.kernel.org/lkml/20200819084751.17686-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For a while we need to have a dummy event for doing things like
receiving PERF_RECORD_COMM, PERF_RECORD_EXEC, etc for threads being
created and dying while we synthesize the pre-existing ones at tool
start.
This 'dummy' event is needed for keeping track of thread lifetime events
early in the session but are uninteresting otherwise, i.e. no need to
have it in a initial events menu for the non-grouped case, i.e. for:
# perf top -e cycles,instructions
or even for plain:
# perf top
When 'cycles' and that 'dummy' event are in place.
The code to remove that 'dummy' event ended up creating an endless loop
for the grouped case, i.e.:
# perf top -e '{cycles,instructions}'
Fix it.
Fixes: bee9ca1c8a237ca1 ("perf report TUI: Remove needless 'dummy' event from menu") Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to hold the whole device bd_mutex to protect against
other thread concurrently deleting out partition before we get
to it, and thus causing a use after free.
Fixes: cddae808aeb7 ("block: pass a hd_struct to delete_partition") Reported-by: syzbot+6448f3c229bc52b82f69@syzkaller.appspotmail.com Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the user's manual chapter 8.2.1 of Loongson 3A2000 CPU [1]
and 3A3000 CPU [2], we should take some event IDs such as 274, 358, 359
and 360 as valid in the check condition, otherwise they are recognized
as "not supported", fix it.
When multiple adapters are present in the system, pci hot-removing second
adapter leads to the following warning as both the adapters registered
thermal zone device with same thermal zone name/type.
Therefore, use unique thermal zone name during thermal zone device
initialization. Also mark thermal zone dev NULL once unregistered.