Commit 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.")
introduced UDP listifyed GRO. The segmentation relies on frag_list being
untouched when passing through the network stack. This assumption can be
broken sometimes, where frag_list itself gets pulled into linear area,
leaving frag_list being NULL. When this happens it can trigger
following NULL pointer dereference, and panic the kernel. Reverse the
test condition should fix it.
Fixes: 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.") Suggested-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Yan Zhai <yan@cloudflare.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/r/Y9gt5EUizK1UImEP@debian Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1796f808e4bb ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
adjusted the policy to enable wakeup by default if the ACPI tables
indicated that a device was wake capable.
It was reported however that this broke suspend on at least two System76
systems in S3 mode and two Lenovo Gen2a systems, but only with S3.
When the machines are set to s2idle, wakeup behaves properly.
Configuring the GPIOs for wakeup with S3 doesn't work properly, so only
set it when the system supports low power idle.
Fixes: 1796f808e4bb ("HID: i2c-hid: acpi: Stop setting wakeup_capable") Fixes: b38f2d5d9615c ("i2c: acpi: Use ACPI wake capability bit to set wake_irq") Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2357 Link: https://bugzilla.redhat.com/show_bug.cgi?id=2162013 Reported-by: Nathan Smythe <ncsmythe@scruboak.org> Tested-by: Nathan Smythe <ncsmythe@scruboak.org> Suggested-by: Raul Rangel <rrangel@chromium.org> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1796f808e4bb ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
changed the policy such that I2C touchpads may be able to wake up the
system by default if the system is configured as such.
However on Clevo NL5xRU there is a mistake in the ACPI tables that the
TP_ATTN# signal connected to GPIO 9 is configured as ActiveLow and level
triggered but connected to a pull up. As soon as the system suspends the
touchpad loses power and then the system wakes up.
To avoid this problem, introduce a quirk for this model that will prevent
the wakeup capability for being set for GPIO 9.
Fixes: 1796f808e4bb ("HID: i2c-hid: acpi: Stop setting wakeup_capable") Reported-by: Werner Sembach <wse@tuxedocomputers.com> Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1722#note_1720627 Co-developed-by: Werner Sembach <wse@tuxedocomputers.com> Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
NVMe controller register access hangs indefinitely when the co-processor
is not running. A missed reset is preferable over a hanging thread since
it could be recoverable.
Signed-off-by: Janne Grunau <j@jannau.net> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix this by initializing rc to 0 as cache_refresh_path() would not set
it in case of success.
Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/all/202301190004.bEHvbKG6-lkp@intel.com/ Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the function sdma_load_context() fails, the sdma_desc will be
freed, but the allocated desc->bd is forgot to be freed.
We already met the sdma_load_context() failure case and the log as
below:
[ 450.699064] imx-sdma 30bd0000.dma-controller: Timeout waiting for CH0 ready
...
In this case, the desc->bd will not be freed without this change.
Make sure calibration values are defined to prevent potential kernel
crashes. This fixes a hypothetical issue for virtual or clone devices
inspired by a similar fix for DS4.
GCC 11.1.0 and 11.2.0 generate a wrong warning when compiling the
kernel e.g. with allmodconfig:
arch/s390/kernel/setup.c: In function ‘setup_lowcore_dat_on’:
./include/linux/fortify-string.h:57:33: error: ‘__builtin_memcpy’ reading 128 bytes from a region of size 0 [-Werror=stringop-overread]
...
arch/s390/kernel/setup.c:526:9: note: in expansion of macro ‘memcpy’
526 | memcpy(abs_lc->cregs_save_area, S390_lowcore.cregs_save_area,
| ^~~~~~
This could be addressed by using absolute_pointer() with the
S390_lowcore macro, but this is not a good idea since this generates
worse code for performance critical paths.
Therefore simply use a for loop to copy the array in question and get
rid of the warning.
When there are no read queues read requests will be assigned a
default queue on allocation. However, blk_mq_get_cached_request() is not
prepared for that and will fail all attempts to grab read requests from
the cache. Worst case it doubles the number of requests allocated,
roughly half of which will be returned by blk_mq_free_plug_rqs().
It only affects batched allocations and so is io_uring specific.
For reference, QD8 t/io_uring benchmark improves by 20-35%.
The Acer Aspire 4810T predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native backlight interface which does
work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At unwind_start(), it is better to get its frame info here rather than
get them outside, even we don't have 'regs'. In this way we can simply
use unwind_{start, next_frame, done} outside.
When multiple interfaces are present in the local interface
list, new skb copy is taken before rx processing except for
the first interface. The address translation happens each
time only on the original skb since the hdr pointer is not
updated properly to the newly created skb.
As a result frames start to drop in userspace when address
based checks or search fails.
Effective offset to add to length was being incorrectly calculated,
which resulted in iomap->length being set to 0, triggering a WARN_ON
in iomap_iter_done().
Fix that, and describe it in comments.
This was reported as a crash by syzbot under an issue about a warning
encountered in iomap_iter_done(), but unrelated to erofs.
The following kernel panic can be triggered when a task with pid=1 attaches
a prog that attempts to send killing signal to itself, also see [1] for more
details:
Stale error status reported from a previous message transaction must be
cleared before starting a new transaction to avoid being confusingly
reported in the following SCMI message dump traces.
arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: pca9547@77: $nodename:0: 'pca9547@77' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dtb: pca9547@77: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@4' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA954x nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
arch/arm/boot/dts/vf610-zii-dev-rev-b.dtb: tca9548@70: $nodename:0: 'tca9548@70' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/arm/boot/dts/vf610-zii-dev-rev-b.dtb: tca9548@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3', 'i2c@4' were unexpected)
From schema: /scratch/geert/linux/linux-renesas/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
...
Fix this by renaming PCA9548 nodes to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
arch/arm/boot/dts/imx53-ppd.dtb: i2c-switch@70: $nodename:0: 'i2c-switch@70' does not match '^(i2c-?)?mux'
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
arch/arm/boot/dts/imx53-ppd.dtb: i2c-switch@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3', 'i2c@4', 'i2c@5', 'i2c@6', 'i2c@7' were unexpected)
From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml
Fix this by renaming the PCA9547 node to "i2c-mux", to match the I2C bus
multiplexer/switch DT bindings and the Generic Names Recommendation in
the Devicetree Specification.
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then passed as a 64 bit function argument. In the case where
i is 32 or more this can lead to an overflow. Avoid this by shifting
using the BIT_ULL macro instead.
Fixes: 471af006a747 ("perf/x86/amd: Constrain Large Increment per Cycle events") Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Ian Rogers <irogers@google.com> Acked-by: Kim Phillips <kim.phillips@amd.com> Link: https://lore.kernel.org/r/20221202135149.1797974-1-colin.i.king@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An SCTP endpoint can start an association through a path and tear it
down over another one. That means the initial path will not see the
shutdown sequence, and the conntrack entry will remain in ESTABLISHED
state for 5 days.
By merging the HEARTBEAT_ACKED and ESTABLISHED states into one
ESTABLISHED state, there remains no difference between a primary or
secondary path. The timeout for the merged ESTABLISHED state is set to
210 seconds (hb_interval * max_path_retrans + rto_max). So, even if a
path doesn't see the shutdown sequence, it will expire in a reasonable
amount of time.
With this change in place, there is now more than one state from which
we can transition to ESTABLISHED, COOKIE_ECHOED and HEARTBEAT_SENT, so
handle the setting of ASSURED bit whenever a state change has happened
and the new state is ESTABLISHED. Removed the check for dir==REPLY since
the transition to ESTABLISHED can happen only in the reply direction.
The preferred form for Renesas' compatible strings is:
"<vendor>,<family>-<module>"
Somehow the compatible string for the r9a09g011 I2C IP was upstreamed
as renesas,i2c-r9a09g011 instead of renesas,r9a09g011-i2c, which
is really confusing, especially considering the generic fallback
is renesas,rzv2m-i2c.
The first user of renesas,i2c-r9a09g011 in the kernel is not yet in
a kernel release, it will be in v6.1, therefore it can still be
fixed in v6.1.
Even if we don't fix it before v6.2, I don't think there is any
harm in making such a change.
s/renesas,i2c-r9a09g011/renesas,r9a09g011-i2c/g for consistency.
Baoquan reported that after triggering a crash the subsequent crash-kernel
fails to boot about half of the time. It triggers a NULL pointer
dereference in the periodic tick code.
This happens because the legacy timer interrupt (IRQ0) is resent in
software which happens in soft interrupt (tasklet) context. In this context
get_irq_regs() returns NULL which leads to the NULL pointer dereference.
The reason for the resend is a spurious APIC interrupt on the IRQ0 vector
which is captured and leads to a resend when the legacy timer interrupt is
enabled. This is wrong because the legacy PIC interrupts are level
triggered and therefore should never be resent in software, but nothing
ever sets the IRQ_LEVEL flag on those interrupts, so the core code does not
know about their trigger type.
Ensure that IRQ_LEVEL is set when the legacy PCI interrupts are set up.
Fixes: a4633adcdbc1 ("[PATCH] genirq: add genirq sw IRQ-retrigger") Reported-by: Baoquan He <bhe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Baoquan He <bhe@redhat.com> Link: https://lore.kernel.org/r/87mt6rjrra.ffs@tglx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I used the wikipedia table for ordering extensions when updating the
pattern here in commit 299824e68bd0 ("dt-bindings: riscv: add new
riscv,isa strings for emulators").
Unfortunately that table did not match canonical order, as defined by
the RISC-V ISA Manual, which defines extension ordering in (what is
currently) Table 41, "Standard ISA extension names". Fix things up by
re-sorting v (vector) and adding p (packed-simd) & j (dynamic
languages). The e (reduced integer) and g (general) extensions are still
intentionally left out.
The RISC-V ISA Manual allows the first multi-letter extension to avoid
a leading underscore. Underscores are only required between multi-letter
extensions.
The dt-binding does not validate that a multi-letter extension is
canonically ordered, as that'd need an even worse regex than is here,
but it should not fail validation for valid ISA strings.
Allow the first multi-letter extension to appear immediately after
the single-letter extensions.
Commit f1e525009493 ("x86/boot: Skip realmode init code when running as
Xen PV guest") missed one code path accessing real_mode_header, leading
to dereferencing NULL when suspending the system under Xen:
Fix that by adding an optional acpi callback allowing to skip setting
the wakeup address, as in the Xen PV case this will be handled by the
hypervisor anyway.
Fixes: f1e525009493 ("x86/boot: Skip realmode init code when running as Xen PV guest") Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://lore.kernel.org/all/20230117155724.22940-1-jgross%40suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hypervisor can enable various new features (SEV_FEATURES[1:63]) and start a
SNP guest. Some of these features need guest side implementation. If any of
these features are enabled without it, the behavior of the SNP guest will be
undefined. It may fail booting in a non-obvious way making it difficult to
debug.
Instead of allowing the guest to continue and have it fail randomly later,
detect this early and fail gracefully.
The SEV_STATUS MSR indicates features which the hypervisor has enabled. While
booting, SNP guests should ascertain that all the enabled features have guest
side implementation. In case a feature is not implemented in the guest, the
guest terminates booting with GHCB protocol Non-Automatic Exit(NAE) termination
request event, see "SEV-ES Guest-Hypervisor Communication Block Standardization"
document (currently at https://developer.amd.com/wp-content/resources/56421.pdf),
section "Termination Request".
Populate SW_EXITINFO2 with mask of unsupported features that the hypervisor can
easily report to the user.
More details in the AMD64 APM Vol 2, Section "SEV_STATUS MSR".
[ bp:
- Massage.
- Move snp_check_features() call to C code.
Note: the CC:stable@ aspect here is to be able to protect older, stable
kernels when running on newer hypervisors. Or not "running" but fail
reliably and in a well-defined manner instead of randomly. ]
Fixes: cbd3d4f7c4e5 ("x86/sev: Check SEV-SNP features support") Signed-off-by: Nikunj A Dadhania <nikunj@amd.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com> Cc: <stable@kernel.org> Link: https://lore.kernel.org/r/20230118061943.534309-1-nikunj@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have got openSUSE reports (Link 1) for 6.1 kernel with khugepaged
stalling CPU for long periods of time. Investigation of tracepoint data
shows that compaction is stuck in repeating fast_find_migrateblock()
based migrate page isolation, and then fails to migrate all isolated
pages.
Commit 7efc3b726103 ("mm/compaction: fix set skip in fast_find_migrateblock")
was suspected as it was merged in 6.1 and in theory can indeed remove a
termination condition for fast_find_migrateblock() under certain
conditions, as it removes a place that always marks a scanned pageblock
from being re-scanned. There are other such places, but those can be
skipped under certain conditions, which seems to match the tracepoint
data.
Testing of revert also appears to have resolved the issue, thus revert
the commit until a more robust solution for the original problem is
developed.
It's also likely this will fix qemu stalls with 6.1 kernel reported in
Link 2, but that is not yet confirmed.
Following line should listen for a rising edge and exit after the first
one since '-c 1' is provided.
# gpio-event-mon -n gpiochip1 -o 0 -r -c 1
It works with kernel 4.19 but it doesn't work with 5.10. In 5.10 the
above command doesn't exit after the first rising edge it keep listening
for an event forever. The '-c 1' is not taken into an account.
The problem is in commit 62757c32d5db ("tools: gpio: add multi-line
monitoring to gpio-event-mon").
Before this commit the iterator 'i' in monitor_device() is used for
counting of the events (loops). In the case of the above command (-c 1)
we should start from 0 and increment 'i' only ones and hit the 'break'
statement and exit the process. But after the above commit counting
doesn't start from 0, it start from 1 when we listen on one line.
It is because 'i' is used from one more purpose, counting of lines
(num_lines) and it isn't restore to 0 after following code
for (i = 0; i < num_lines; i++)
gpiotools_set_bit(&values.mask, i);
Restore the initial value of the iterator to 0 in order to allow counting
of loops to work for any cases.
Fixes: 62757c32d5db ("tools: gpio: add multi-line monitoring to gpio-event-mon") Signed-off-by: Ivo Borisov Shopov <ivoshopov@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[Bartosz: tweak the commit message] Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
I'm not exactly clear on what strange workflow causes people to do it,
but clearly occasionally some files end up being committed as executable
even though they clearly aren't.
This is a reprise of commit 90fda63fa115 ("treewide: fix up files
incorrectly marked executable"), just with a different set of files (but
with the same trivial shell scripting).
So apparently we need to re-do this every five years or so, and Joe
needs to just keep reminding me to do so ;)
Reported-by: Joe Perches <joe@perches.com> Fixes: 523375c943e5 ("drm/vmwgfx: Port vmwgfx to arm64") Fixes: 5c439937775d ("ASoC: codecs: add support for ES8326") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'ublk_chr_class' is needed when deleting ublk char devices in
ublk_exit(), so move it after devices(idle) are removed.
Fixes the following warning reported by Harris, James R:
[ 859.178950] sysfs group 'power' not found for kobject 'ublkc0'
[ 859.178962] WARNING: CPU: 3 PID: 1109 at fs/sysfs/group.c:278 sysfs_remove_group+0x9c/0xb0
It turns out the optimisation implemented by commit 4f2c3872dde5 is
totally broken, since all the places that consume hw->dtcs_used for
events other than cycle count are still not expecting it to be sparsely
populated, and fail to read all the relevant DTC counters correctly if
so.
If implemented correctly, the optimisation potentially saves up to 3
register reads per event update, which is reasonably significant for
events targeting a single node, but still not worth a massive amount of
additional code complexity overall. Getting it right within the current
design looks a fair bit more involved than it was ever intended to be,
so let's just make a functional revert which restores the old behaviour
while still backporting easily.
netif_stop_queue() and netif_wake_queue() act on TX queue 0. This is ok
as long as only a single TX queue is supported. But support for multiple
TX queues was introduced with 762031375d5c and I missed to adapt stop
and wake of TX queues.
Use netif_stop_subqueue() and netif_tx_wake_queue() to act on specific
TX queue.
During EEH error injection testing, a deadlock was encountered in the tg3
driver when tg3_io_error_detected() was attempting to cancel outstanding
reset tasks:
Code inspection shows that both tg3_io_error_detected() and
tg3_reset_task() attempt to acquire the RTNL lock at the beginning of
their code blocks. If tg3_reset_task() should happen to execute between
the times when tg3_io_error_deteced() acquires the RTNL lock and
tg3_reset_task_cancel() is called, a deadlock will occur.
Moving tg3_reset_task_cancel() call earlier within the code block, prior
to acquiring RTNL, prevents this from happening, but also exposes another
deadlock issue where tg3_reset_task() may execute AFTER
tg3_io_error_detected() has executed:
If "capacity-dmips-mhz" is present in a CPU DT node,
topology_parse_cpu_capacity() will fail to allocate memory. arm64, with
which this code path is shared, does not call
topology_parse_cpu_capacity() until later in boot where memory
allocation is available. While "capacity-dmips-mhz" is not yet a valid
property on RISC-V, invalid properties should be ignored rather than
cause issues. Move init_cpu_topology(), which calls
topology_parse_cpu_capacity(), to a later initialization stage, to match
arm64.
As a side effect of this change, RISC-V is "protected" from changes to
core topology code that would work on arm64 where memory allocation is
safe but on RISC-V isn't.
In order to prevent int340x_thermal_get_trip_type() from possibly
racing with int340x_thermal_read_trips() invoked by int3403_notify()
add locking to it in analogy with int340x_thermal_get_trip_temp().
Fixes: 6757a7abe47b ("thermal: intel: int340x: Protect trip temperature from concurrent updates") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we have a race where we look up a sock through a "general"
(ie, not directly associated with the (src,dest,tag) tuple) key, then
drop the key reference while still holding the key's sock.
This change expands the key reference until we've finished using the
sock, and hence the sock reference too.
Commit message changes from Jeremy Kerr <jk@codeconstruct.com.au>.
Reported-by: Noam Rathaus <noamr@ssd-disclosure.com> Fixes: 73c618456dc5 ("mctp: locking, lifetime and validity changes for sk_keys") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we delete the key expiry timer (in sk->close) before
unhashing the sk. This means that another thread may find the sk through
its presence on the key list, and re-queue the timer.
This change moves the timer deletion to the unhash, after we have made
the key no longer observable, so the timer cannot be re-queued.
Fixes: 7b14e15ae6f4 ("mctp: Implement a timeout for tags") Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we correlate the mctp_sk_key lifetime to the sock lifetime
through the sock hash/unhash operations, but this is pretty tenuous, and
there are cases where we may have a temporary reference to an unhashed
sk.
This change makes the reference more explicit, by adding a hold on the
sock when it's associated with a mctp_sk_key, released on final key
unref.
Fixes: 73c618456dc5 ("mctp: locking, lifetime and validity changes for sk_keys") Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since this driver enables the interrupt by RIC2_QFE1, this driver
should clear the interrupt flag if it happens. Otherwise, the interrupt
causes to hang the system.
Note that this also fix a minor coding style (a comment indentation)
around the fixed code.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
After system entered Suspend to RAM, registers setting of this
hardware is reset because the SoC will be turned off. On R-Car Gen3
(info->ccc_gac), ravb_ptp_init() is called in ravb_probe() only. So,
after system resumed, it lacks of the initial settings for ptp. So,
add ravb_ptp_{init,stop}() into ravb_{resume,suspend}().
Fixes: f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, if you bind the socket to something like:
servaddr.sin6_family = AF_INET6;
servaddr.sin6_port = htons(0);
servaddr.sin6_scope_id = 0;
inet_pton(AF_INET6, "::1", &servaddr.sin6_addr);
And then request a connect to:
connaddr.sin6_family = AF_INET6;
connaddr.sin6_port = htons(20000);
connaddr.sin6_scope_id = if_nametoindex("lo");
inet_pton(AF_INET6, "fe88::1", &connaddr.sin6_addr);
What the stack does is:
- bind the socket
- create a new asoc
- to handle the connect
- copy the addresses that can be used for the given scope
- try to connect
But the copy returns 0 addresses, and the effect is that it ends up
trying to connect as if the socket wasn't bound, which is not the
desired behavior. This unexpected behavior also allows KASLR leaks
through SCTP diag interface.
The fix here then is, if when trying to copy the addresses that can
be used for the scope used in connect() it returns 0 addresses, bail
out. This is what TCP does with a similar reproducer.
The trace_types_lock is held when osnoise_tracer_stop() or
timerlat_tracer_stop() are called in the non-RCU read side section.
So, pass lockdep_is_held(&trace_types_lock) to silence false lockdep
warning.
Link: https://lkml.kernel.org/r/20221227023036.784337-1-nashuiliang@gmail.com Cc: Masami Hiramatsu <mhiramat@kernel.org> Fixes: dae181349f1e ("tracing/osnoise: Support a list of trace_array *tr") Acked-by: Daniel Bristot de Oliveira <bristot@kernel.org> Signed-off-by: Chuang Wang <nashuiliang@gmail.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some apple laptop models have an ACPI device with a HID of APP000B
and that device has an IO resource (so it does not describe the new
unsupported MMIO based gmux type), but there actually is no gmux
in the laptop at all.
The gmux_probe() function of the actual apple-gmux driver has code
to detect this, this code has been factored out into a new
apple_gmux_detect() helper in apple-gmux.h.
Use this new function to fix acpi_video_get_backlight_type() wrongly
returning apple_gmux as type on the following laptops:
Add a new (static inline) apple_gmux_detect() helper to apple-gmux.h
which can be used for gmux detection instead of apple_gmux_present().
The latter is not really reliable since an ACPI device with a HID
of APP000B is present on some devices without a gmux at all, as well
as on devices with a newer (unsupported) MMIO based gmux model.
This causes apple_gmux_present() to return false-positives on
a number of different Apple laptop models.
This new helper uses the same probing as the actual apple-gmux
driver, so that it does not return false positives.
To avoid code duplication the gmux_probe() function of the actual
driver is also moved over to using the new apple_gmux_detect() helper.
This avoids false positives (vs _HID + IO region detection) on:
This is a preparation patch for adding a new static inline
apple_gmux_detect() helper which actually checks a supported
gmux is present, rather then only checking an ACPI device with
the HID is there as apple_gmux_present() does.
Commit 1ea0d3b46798 ("platform/x86: asus-wmi: Simplify tablet-mode-switch
handling") unified the asus-wmi tablet-switch handling, but it did not take
into account that the value returned for the kbd_dock_devid WMI method is
inverted where as the other ones are not inverted.
This causes asus-wmi to report an inverted tablet-switch state for devices
which use the kbd_dock_devid, which causes libinput to ignore touchpad
events while the affected T10x model 2-in-1s are docked.
Add inverting of the return value in the kbd_dock_devid case to fix this.
syzbot reported a use-after-free in do_accept(), precisely nr_accept()
as sk_prot_alloc() allocated the memory and sock_put() frees it. [0]
The issue could happen if the heartbeat timer is fired and
nr_heartbeat_expiry() calls nr_destroy_socket(), where a socket
has SOCK_DESTROY or a listening socket has SOCK_DEAD.
In this case, the first condition cannot be true. SOCK_DESTROY is
flagged in nr_release() only when the file descriptor is close()d,
but accept() is being called for the listening socket, so the second
condition must be true.
Usually, the AF_NETROM listener neither starts timers nor sets
SOCK_DEAD. However, the condition is met if connect() fails before
listen(). connect() starts the t1 timer and heartbeat timer, and
t1timer calls nr_disconnect() when timeout happens. Then, SOCK_DEAD
is set, and if we call listen(), the heartbeat timer calls
nr_destroy_socket().
This path seems expected, and nr_destroy_socket() is called to clean
up resources. Initially, there was sock_hold() before nr_destroy_socket()
so that the socket would not be freed, but the commit 517a16b1a88b
("netrom: Decrease sock refcount when sock timers expire") accidentally
removed it.
To fix use-after-free, let's add sock_hold().
[0]:
BUG: KASAN: use-after-free in do_accept+0x483/0x510 net/socket.c:1848
Read of size 8 at addr ffff88807978d398 by task syz-executor.3/5315
RFC 9260, Sec 8.5.1 states that for ABORT/SHUTDOWN_COMPLETE, the chunk
MUST be accepted if the vtag of the packet matches its own tag and the
T bit is not set OR if it is set to its peer's vtag and the T bit is set
in chunk flags. Otherwise the packet MUST be silently dropped.
Update vtag verification for ABORT/SHUTDOWN_COMPLETE based on the above
description.
Driver marked broadcast/multicast frames as offloaded incorrectly.
Mark them as offloaded only when HW offloading has been enabled.
This should happen only for ADIN2111 when both ports are bridged
by the software.
Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support") Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230120090846.18172-1-alexandru.tachici@analog.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Starting with commit eee16b147121 ("net: dsa: microchip: perform the
compatibility check for dev probed"), the KSZ switch driver now bails
out if it thinks the DT compatible doesn't match the actual chip ID
read back from the hardware:
ksz9477-switch 1-005f: Device tree specifies chip KSZ9893 but found
KSZ8563, please fix it!
For the KSZ8563, which used ksz_switch_chips[KSZ9893], this was fine
at first, because it indeed shares the same chip id as the KSZ9893.
Commit b44908095612 ("net: dsa: microchip: add separate struct
ksz_chip_data for KSZ8563 chip") started differentiating KSZ9893
compatible chips by consulting the 0x1F register. The resulting breakage
was fixed for the SPI driver in the same commit by introducing the
appropriate ksz_switch_chips[KSZ8563], but not for the I2C driver.
Fix this for I2C-connected KSZ8563 now to get it probing again.
Fixes: b44908095612 ("net: dsa: microchip: add separate struct ksz_chip_data for KSZ8563 chip"). Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230120110933.1151054-1-a.fatoum@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
if (!type)
continue;
if (type > RTAX_MAX)
return false;
...
fi_val = fi->fib_metrics->metrics[type - 1];
@type being used as an array index, we need to prevent
cpu speculation or risk leaking kernel memory content.
Fixes: 5f9ae3d9e7e4 ("ipv4: do metrics match when looking up and deleting a route") Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20230120133140.3624204-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reminds us netlink_getname() runs locklessly [1]
This first patch annotates the race against nlk->portid.
Following patches take care of the remaining races.
[1]
BUG: KCSAN: data-race in netlink_getname / netlink_insert
write to 0xffff88814176d310 of 4 bytes by task 2315 on cpu 1:
netlink_insert+0xf1/0x9a0 net/netlink/af_netlink.c:583
netlink_autobind+0xae/0x180 net/netlink/af_netlink.c:856
netlink_sendmsg+0x444/0x760 net/netlink/af_netlink.c:1895
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
____sys_sendmsg+0x38f/0x500 net/socket.c:2476
___sys_sendmsg net/socket.c:2530 [inline]
__sys_sendmsg+0x19a/0x230 net/socket.c:2559
__do_sys_sendmsg net/socket.c:2568 [inline]
__se_sys_sendmsg net/socket.c:2566 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2566
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
read to 0xffff88814176d310 of 4 bytes by task 2316 on cpu 0:
netlink_getname+0xcd/0x1a0 net/netlink/af_netlink.c:1144
__sys_getsockname+0x11d/0x1b0 net/socket.c:2026
__do_sys_getsockname net/socket.c:2041 [inline]
__se_sys_getsockname net/socket.c:2038 [inline]
__x64_sys_getsockname+0x3e/0x50 net/socket.c:2038
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x00000000 -> 0xc9a49780
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 2316 Comm: syz-executor.2 Not tainted 6.2.0-rc3-syzkaller-00030-ge8f60cd7db24-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Skip interference with an ongoing transaction, do not perform garbage
collection on inactive elements. Reset annotated previous end interval
if the expired element is marked as busy (control plane removed the
element right before expiration).
...instead of a tree descent, which became overly complicated in an
attempt to cover cases where expired or inactive elements would affect
comparisons with the new element being inserted.
Further, it turned out that it's probably impossible to cover all those
cases, as inactive nodes might entirely hide subtrees consisting of a
complete interval plus a node that makes the current insertion not
overlap.
To speed up the overlap check, descent the tree to find a greater
element that is closer to the key value to insert. Then walk down the
node list for overlap detection. Starting the overlap check from
rb_first() unconditionally is slow, it takes 10 times longer due to the
full linear traversal of the list.
Moreover, perform garbage collection of expired elements when walking
down the node list to avoid bogus overlap reports.
For the insertion operation itself, this essentially reverts back to the
implementation before commit 7c84d41416d8 ("netfilter: nft_set_rbtree:
Detect partial overlaps on insertion"), except that cases of complete
overlap are already handled in the overlap detection phase itself, which
slightly simplifies the loop to find the insertion point.
Based on initial patch from Stefano Brivio, including text from the
original patch description too.
The Asus U46E backlight tables have a set of interesting problems:
1. Its ACPI tables do make _OSI ("Windows 2012") checks, so
acpi_osi_is_win8() should return true.
But the tables have 2 sets of _OSI calls, one from the usual global
_INI method setting a global OSYS variable and a second set of _OSI
calls from a MSOS method and the MSOS method is the only one calling
_OSI ("Windows 2012").
The MSOS method only gets called in the following cases:
1. From some Asus specific WMI methods
2. From _DOD, which only runs after acpi_video_get_backlight_type()
has already been called by the i915 driver
3. From other ACPI video bus methods which never run (see below)
4. From some EC query callbacks
So when i915 calls acpi_video_get_backlight_type() MSOS has never run
and acpi_osi_is_win8() returns false, so acpi_video_get_backlight_type()
returns acpi_video as the desired backlight type, which causes
the intel_backlight device to not register.
2. _DOD effectively does this:
Return (Package (0x01)
{
0x0400
})
causing acpi_video_device_in_dod() to return false, which causes
the acpi_video backlight device to not register.
Leaving the user with no backlight device at all. Note that before 6.1.y
the i915 driver would register the intel_backlight device unconditionally
and since that then was the only backlight device userspace would use that.
Add a backlight=native DMI quirk for this special laptop to restore
the old (and working) behavior of the intel_backlight device registering.
Fixes: fb1836c91317 ("ACPI: video: Prefer native over vendor") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HP EliteBook 8460p predates Windows 8, so it defaults to using
acpi_video# for backlight control.
Starting with the 6.1.y kernels the native radeon_bl0 backlight is hidden
in this case instead of relying on userspace preferring acpi_video# over
native backlight devices.
It turns out that for the acpi_video# interface to work on
the HP EliteBook 8460p, the brightness needs to be set at least once
through the native interface, which now no longer is done breaking
backlight control.
The native interface however always works without problems, so add
a quirk to use native backlight on the EliteBook 8460p to fix this.
Fixes: fb1836c91317 ("ACPI: video: Prefer native over vendor") Link: https://bugzilla.redhat.com/show_bug.cgi?id=2161428 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The HP Pavilion g6-1d80nr predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native backlight interface which does
work properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 9dcb34234b82 ("ACPI: video: Add backlight=native DMI quirk for HP EliteBook 8460p") Signed-off-by: Sasha Levin <sashal@kernel.org>
All nvme transports should be using the same flags for their tagsets,
with the exception for the blocking flag that should only be set for
transports that can block in ->queue_rq.
Add a NVME_F_BLOCKING flag to nvme_ctrl_ops to control the blocking
behavior and lift setting the flags into nvme_alloc_{admin,io}_tag_set.
Allow the transport driver to override the attribute groups for the
control device, so that the PCIe driver doesn't manually have to add a
group after device creation and keep track of it.
The page_pool_release_page was used when freeing rx buffers, and this
function just unmaps the page (if mapped) and does not recycle the page.
So after hundreds of down/up the eth0, the system will out of memory.
For more details, please refer to the following reproduce steps and
bug logs. To solve this issue and refer to the doc of page pool, the
page_pool_put_full_page should be used to replace page_pool_release_page.
Because this API will try to recycle the page if the page refcnt equal to
1. After testing 20000 times, the issue can not be reproduced anymore
(about testing 391 times the issue will occur on i.MX8MN-EVK before).
Reproduce steps:
Create the test script and run the script. The script content is as
follows:
LOOPS=20000
i=1
while [ $i -le $LOOPS ]
do
echo "TINFO:ENET $curface up and down test $i times"
org_macaddr=$(cat /sys/class/net/eth0/address)
ifconfig eth0 down
ifconfig eth0 hw ether $org_macaddr up
i=$(expr $i + 1)
done
sleep 5
if cat /sys/class/net/eth0/operstate | grep 'up';then
echo "TEST PASS"
else
echo "TEST FAIL"
fi
Fixes: 95698ff6177b ("net: fec: using page pool to manage RX buffers") Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: shenwei wang <Shenwei.wang@nxp.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If net_assign_generic() fails, the current error path in ops_init() tries
to clear the gen pointer slot. Anyway, in such error path, the gen pointer
itself has not been modified yet, and the existing and accessed one is
smaller than the accessed index, causing an out-of-bounds error:
BUG: KASAN: slab-out-of-bounds in ops_init+0x2de/0x320
Write of size 8 at addr ffff888109124978 by task modprobe/1018
Most netlink attributes are parsed and validated from
__nla_validate_parse() or validate_nla()
u16 type = nla_type(nla);
if (type == 0 || type > maxtype) {
/* error or continue */
}
@type is then used as an array index and can be used
as a Spectre v1 gadget.
array_index_nospec() can be used to prevent leaking
content of kernel memory to malicious users.
This should take care of vast majority of netlink uses,
but an audit is needed to take care of others where
validation is not yet centralized in core netlink functions.
iavf_replace_primary_mac() utilizes queue_work() to schedule the
watchdog task but that only ensures that the watchdog task is queued
to run. To make sure the watchdog is executed asap use
mod_delayed_work().
Without this patch it may take up to 2s until the watchdog task gets
executed, which may cause long delays when setting the MAC address.
Fixes: a3e839d539e0 ("iavf: Add usage of new virtchnl format to set default MAC") Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Reviewed-by: Michal Schmidt <mschmidt@redhat.com> Tested-by: Michal Schmidt <mschmidt@redhat.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We are seeing an issue where setting the MAC address on iavf fails with
EAGAIN after the 2.5s timeout expires in iavf_set_mac().
There is the following deadlock scenario:
iavf_set_mac(), holding rtnl_lock, waits on:
iavf_watchdog_task (within iavf_wq) to send a message to the PF,
and
iavf_adminq_task (within iavf_wq) to receive a response from the PF.
In this adapter state (>=__IAVF_DOWN), these tasks do not need to take
rtnl_lock, but iavf_wq is a global single-threaded workqueue, so they
may get stuck waiting for another adapter's iavf_watchdog_task to run
iavf_init_config_adapter(), which does take rtnl_lock.
The deadlock resolves itself by the timeout in iavf_set_mac(),
which results in EAGAIN returned to userspace.
Let's break the deadlock loop by changing iavf_wq into a per-adapter
workqueue, so that one adapter's tasks are not blocked by another's.
Fixes: 35a2443d0910 ("iavf: Add waiting for response from PF in set mac") Co-developed-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drm_vma_node_allow() and drm_vma_node_revoke() should be called in
balanced pairs. We call drm_vma_node_allow() once per-file everytime a
user calls mmap_offset, but only call drm_vma_node_revoke once per-file
on each mmap_offset. As the mmap_offset is reused by the client, the
per-file vm_count may remain non-zero and the rbtree leaked.
Call drm_vma_node_allow_once() instead to prevent that memory leak.
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Andi Shyti <andi.shyti@linux.intel.com> Signed-off-by: Nirmoy Das <nirmoy.das@intel.com> Fixes: 786555987207 ("drm/i915/gem: Store mmap_offsets in an rbtree rather than a plain list") Reported-by: Chuansheng Liu <chuansheng.liu@intel.com> Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com> Link: https://lore.kernel.org/r/20230117175236.22317-2-nirmoy.das@intel.com Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently there is no easy way for a drm driver to safely check and allow
drm_vma_offset_node for a drm file just once. Allow drm drivers to call
non-refcounted version of drm_vma_node_allow() so that a driver doesn't
need to keep track of each drm_vma_node_allow() to call subsequent
drm_vma_node_revoke() to prevent memory leak.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: David Airlie <airlied@gmail.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Andi Shyti <andi.shyti@linux.intel.com> Suggested-by: Chris Wilson <chris.p.wilson@intel.com> Signed-off-by: Nirmoy Das <nirmoy.das@intel.com> Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com> Link: https://lore.kernel.org/r/20230117175236.22317-1-nirmoy.das@intel.com Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that i2c_mark_adapter_suspended() is always balanced by a call to
i2c_mark_adapter_resumed().
dw_i2c_plat_resume() must always be called, so that
i2c_mark_adapter_resumed() is called. This is not compatible with
DPM_FLAG_MAY_SKIP_RESUME, so remove the flag.
Since the controller is always resumed on system resume the
dw_i2c_plat_complete() callback is redundant and has been removed.
The unbalanced suspended flag was introduced by commit c57813b8b288
("i2c: designware: Lock the adapter while setting the suspended flag")
Before that commit, the system and runtime PM used the same functions. The
DPM_FLAG_MAY_SKIP_RESUME was used to skip the system resume if the driver
had been in runtime-suspend. If system resume was skipped, the suspended
flag would be cleared by the next runtime resume. The check of the
suspended flag was _after_ the call to pm_runtime_get_sync() in
i2c_dw_xfer(). So either a system resume or a runtime resume would clear
the flag before it was checked.
Having introduced the unbalanced suspended flag with that commit, a further
commit 80704a84a9f8
("i2c: designware: Use the i2c_mark_adapter_suspended/resumed() helpers")
changed from using a local suspended flag to using the
i2c_mark_adapter_suspended/resumed() functions. These use a flag that is
checked by I2C core code before issuing the transfer to the bus driver, so
there was no opportunity for the bus driver to runtime resume itself before
the flag check.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: c57813b8b288 ("i2c: designware: Lock the adapter while setting the suspended flag") Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In functions i2c_dw_scl_lcnt() and i2c_dw_scl_hcnt() may have overflow
by depending on the values of the given parameters including the ic_clk.
For example in our use case where ic_clk is larger than one million,
multiplication of ic_clk * 4700 will result in 32 bit overflow.
Add cast of u64 to the calculation to avoid multiplication overflow, and
use the corresponding define for divide.
Fixes: 2373f6b9744d ("i2c-designware: split of i2c-designware.c into core and bus specific parts") Signed-off-by: Lareine Khawaly <lareine@amazon.com> Signed-off-by: Hanna Hawa <hhhawa@amazon.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Drain requests all go through io_drain_req, which has a quick exit in case
there is nothing pending (ie the drain is not useful). In that case it can
run the issue the request immediately.
However for safety it queues it through task work.
The problem is that in this case the request is run asynchronously, but
the async work has not been prepared through io_req_prep_async.
This has not been a problem up to now, as the task work always would run
before returning to userspace, and so the user would not have a chance to
race with it.
However - with IORING_SETUP_DEFER_TASKRUN - this is no longer the case and
the work might be defered, giving userspace a chance to change data being
referred to in the request.
Instead _always_ prep_async for drain requests, which is simpler anyway
and removes this issue.
projects / linux-stable / log