The HDaudio stream allocation is done first, and in a second step the
LOSIDV parameter is programmed for the multi-link used by a codec.
This leads to a possible stream_tag leak, e.g. if a DisplayAudio link
is not used. This would happen when a non-Intel graphics card is used
and userspace unconditionally uses the Intel Display Audio PCMs without
checking if they are connected to a receiver with jack controls.
We should first check that there is a valid multi-link entry to
configure before allocating a stream_tag. This change aligns the
dma_assign and dma_cleanup phases.
Complements: b0cd60f3e9f5 ("ALSA/ASoC: hda: clarify bus_get_link() and bus_link_get() helpers") Link: https://github.com/thesofproject/linux/issues/4151 Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Rander Wang <rander.wang@intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20230216162340.19480-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs group containing the cmb attributes is registered before the
driver knows if they need to be visible or not. Update the group when
cmb attributes are known to exist so the visibility setting is correct.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217037 Fixes: 86adbf0cdb9ec65 ("nvme: simplify transport specific device attribute handling") Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported a RCU stall which is caused by setting up an alarmtimer
with a very small interval and ignoring the signal. The reproducer arms the
alarm timer with a relative expiry of 8ns and an interval of 9ns. Not a
problem per se, but that's an issue when the signal is ignored because then
the timer is immediately rearmed because there is no way to delay that
rearming to the signal delivery path. See posix_timer_fn() and commit 58229a189942 ("posix-timers: Prevent softirq starvation by small intervals
and SIG_IGN") for details.
The reproducer does not set SIG_IGN explicitely, but it sets up the timers
signal with SIGCONT. That has the same effect as explicitely setting
SIG_IGN for a signal as SIGCONT is ignored if there is no handler set and
the task is not ptraced.
It works because the tasks are traced and therefore the signal is queued so
the tracer can see it, which delays the restart of the timer to the signal
delivery path. But then the tracer is killed:
syzkaller login: [ 79.439102][ C0] hrtimer: interrupt took 68471 ns
[ 184.460538][ C1] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
...
[ 184.658237][ C1] rcu: Stack dump where RCU GP kthread last ran:
[ 184.664574][ C1] Sending NMI from CPU 1 to CPUs 0:
[ 184.669821][ C0] NMI backtrace for cpu 0
[ 184.669831][ C0] CPU: 0 PID: 5108 Comm: syz-executor192 Not tainted 6.2.0-rc6-next-20230203-syzkaller #0
...
[ 184.670036][ C0] Call Trace:
[ 184.670041][ C0] <IRQ>
[ 184.670045][ C0] alarmtimer_fired+0x327/0x670
posix_timer_fn() prevents that by checking whether the interval for
timers which have the signal ignored is smaller than a jiffie and
artifically delay it by shifting the next expiry out by a jiffie. That's
accurate vs. the overrun accounting, but slightly inaccurate
vs. timer_gettimer(2).
The comment in that function says what needs to be done and there was a fix
available for the regular userspace induced SIG_IGN mechanism, but that did
not work due to the implicit ignore for SIGCONT and similar signals. This
needs to be worked on, but for now the only available workaround is to do
exactly what posix_timer_fn() does:
Increase the interval of self-rearming timers, which have their signal
ignored, to at least a jiffie.
Interestingly this has been fixed before via commit ff86bf0c65f1
("alarmtimer: Rate limit periodic intervals") already, but that fix got
lost in a later rework.
Reported-by: syzbot+b9564ba6e8e00694511b@syzkaller.appspotmail.com Fixes: f2c45807d399 ("alarmtimer: Switch over to generic set/get/rearm routine") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: John Stultz <jstultz@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/87k00q1no2.ffs@tglx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that KVM disables vPMU support on hybrid CPUs, WARN and return zeros
if perf_get_x86_pmu_capability() is invoked on a hybrid CPU. The helper
doesn't provide an accurate accounting of the PMU capabilities for hybrid
CPUs and needs to be enhanced if KVM, or anything else outside of perf,
wants to act on the PMU capabilities.
Cc: stable@vger.kernel.org Cc: Andrew Cooper <Andrew.Cooper3@citrix.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Link: https://lore.kernel.org/all/20220818181530.2355034-1-kan.liang@linux.intel.com Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230208204230.1360502-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling the KVM_GET_DEBUGREGS ioctl, on some configurations, there
might be some unitialized portions of the kvm_debugregs structure that
could be copied to userspace. Prevent this as is done in the other kvm
ioctls, by setting the whole structure to 0 before copying anything into
it.
Bonus is that this reduces the lines of code as the explicit flag
setting and reserved space zeroing out can be removed.
Cc: Sean Christopherson <seanjc@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: <x86@kernel.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: stable <stable@kernel.org> Reported-by: Xingyuan Mo <hdthky0@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message-Id: <20230214103304.3689213-1-gregkh@linuxfoundation.org> Tested-by: Xingyuan Mo <hdthky0@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable KVM support for virtualizing PMUs on hosts with hybrid PMUs until
KVM gains a sane way to enumeration the hybrid vPMU to userspace and/or
gains a mechanism to let userspace opt-in to the dangers of exposing a
hybrid vPMU to KVM guests. Virtualizing a hybrid PMU, or at least part of
a hybrid PMU, is possible, but it requires careful, deliberate
configuration from userspace.
E.g. to expose full functionality, vCPUs need to be pinned to pCPUs to
prevent migrating a vCPU between a big core and a little core, userspace
must enumerate a reasonable topology to the guest, and guest CPUID must be
curated per vCPU to enumerate accurate vPMU capabilities.
The last point is especially problematic, as KVM doesn't control which
pCPU it runs on when enumerating KVM's vPMU capabilities to userspace,
i.e. userspace can't rely on KVM_GET_SUPPORTED_CPUID in it's current form.
Alternatively, userspace could enable vPMU support by enumerating the
set of features that are common and coherent across all cores, e.g. by
filtering PMU events and restricting guest capabilities. But again, that
requires userspace to take action far beyond reflecting KVM's supported
feature set into the guest.
For now, simply disable vPMU support on hybrid CPUs to avoid inducing
seemingly random #GPs in guests, and punt support for hybrid CPUs to a
future enabling effort.
Reported-by: Jianfeng Gao <jianfeng.gao@intel.com> Cc: stable@vger.kernel.org Cc: Andrew Cooper <Andrew.Cooper3@citrix.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Link: https://lore.kernel.org/all/20220818181530.2355034-1-kan.liang@linux.intel.com Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230208204230.1360502-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when starting error recovery there might be a authentication work
running, and it involves I/O commands. Given the controller is tearing
down there is no chance for the I/O to complete other than timing out
which may unnecessarily take a full io timeout.
So first tear down the queues, fail/cancel all inflight I/O (including
potentially authentication) and only then stop authentication. This
ensures that failover is not stalled due to blocked authentication I/O.
when starting error recovery there might be a authentication work
running, and it involves I/O commands. Given the controller is tearing
down there is no chance for the I/O to complete other than timing out
which may unnecessarily take a full io timeout.
So first tear down the queues, fail/cancel all inflight I/O (including
potentially authentication) and only then stop authentication. This
ensures that failover is not stalled due to blocked authentication I/O.
The result of nlmsg_find_attr() 'br_spec' is dereferenced in
nla_for_each_nested(), but it can take NULL value in nla_find() function,
which will result in an error.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 51616018dd1b ("i40e: Add support for getlink, setlink ndo ops") Signed-off-by: Natalia Petrova <n.petrova@fintech.ru> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20230209172833.3596034-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
After x86 enabled support for KMSAN, it has become possible to have larger
'struct page' than was expected when commit 5470dea49f53 ("mm: use
mm_zero_struct_page from SPARC on all 64b architectures") was merged:
include/linux/mm.h:156:10: warning: no case matching constant switch condition '96'
switch (sizeof(struct page)) {
Extend the maximum accordingly.
Link: https://lkml.kernel.org/r/20230130130739.563628-1-arnd@kernel.org Fixes: 5470dea49f53 ("mm: use mm_zero_struct_page from SPARC on all 64b architectures") Fixes: 4ca8cc8d1bbe ("x86: kmsan: enable KMSAN builds for x86") Fixes: f80be4571b19 ("kmsan: add KMSAN runtime core") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Pasha Tatashin <pasha.tatashin@soleen.com> Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Alex Sierra <alex.sierra@amd.com> Cc: David Hildenbrand <david@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Liam R. Howlett <Liam.Howlett@Oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take into account the IPV6_TCLASS socket option (DSCP) in
tcp_v6_connect(). Otherwise fib6_rule_match() can't properly
match the DSCP value, resulting in invalid route lookup.
For example:
ip route add unreachable table main 2001:db8::10/124
ip route add table 100 2001:db8::10/124 dev eth0
ip -6 rule add dsfield 0x04 table 100
echo test | socat - TCP6:[2001:db8::11]:54321,ipv6-tclass=0x04
Without this patch, socat fails at connect() time ("No route to host")
because the fib-rule doesn't jump to table 100 and the lookup ends up
being done in the main table.
Fixes: 2cc67cc731d9 ("[IPV6] ROUTE: Routing by Traffic Class.") Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take into account the IPV6_TCLASS socket option (DSCP) in
ip6_datagram_flow_key_init(). Otherwise fib6_rule_match() can't
properly match the DSCP value, resulting in invalid route lookup.
For example:
ip route add unreachable table main 2001:db8::10/124
ip route add table 100 2001:db8::10/124 dev eth0
ip -6 rule add dsfield 0x04 table 100
echo test | socat - UDP6:[2001:db8::11]:54321,ipv6-tclass=0x04
Without this patch, socat fails at connect() time ("No route to host")
because the fib-rule doesn't jump to table 100 and the lookup ends up
being done in the main table.
Fixes: 2cc67cc731d9 ("[IPV6] ROUTE: Routing by Traffic Class.") Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix handling of the tsync interrupt to compare the pin number with
IGB_N_SDP instead of IGB_N_EXTTS/IGB_N_PEROUT and fix the indexing to
the perout array.
Fixes: cf99c1dd7b77 ("igb: move PEROUT and EXTTS isr logic to separate functions") Reported-by: Matt Corallo <ntp-lists@mattcorallo.com> Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20230213185822.3960072-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the SFP NICs no longer get link at all. Reverting commit a97f8783a937
or switching to the Intel out-of-tree driver both fix the problem.
Per the igb out-of-tree driver, I2C bit banging on i350 depends on
support for an external thermal sensor (ETS). However, commit a97f8783a937 added bit banging unconditionally. Additionally, the
out-of-tree driver always calls init_thermal_sensor_thresh on probe,
while our driver only calls init_thermal_sensor_thresh only in
igb_reset(), and only if an ETS is present, ignoring the internal
thermal sensor. The affected SFPs don't provide an ETS. Per Intel,
the behaviour is a result of i350 firmware requirements.
This patch fixes the problem by aligning the behaviour to the
out-of-tree driver:
- split igb_init_i2c() into two functions:
- igb_init_i2c() only performs the basic I2C initialization.
- igb_set_i2c_bb() makes sure that E1000_CTRL_I2C_ENA is set
and enables bit-banging.
- igb_probe() only calls igb_set_i2c_bb() if an ETS is present.
- igb_reset() aligns its behaviour to igb_probe(), i. e., call
igb_set_i2c_bb() if an ETS is present and call
init_thermal_sensor_thresh() unconditionally.
lianhui reports that when MPLS fails to register the sysctl table
under new location (during device rename) the old pointers won't
get overwritten and may be freed again (double free).
Handle this gracefully. The best option would be unregistering
the MPLS from the device completely on failure, but unfortunately
mpls_ifdown() can fail. So failing fully is also unreliable.
Another option is to register the new table first then only
remove old one if the new one succeeds. That requires more
code, changes order of notifications and two tables may be
visible at the same time.
sysctl point is not used in the rest of the code - set to NULL
on failures and skip unregister if already NULL.
Reported-by: lianhui tang <bluetlh@gmail.com> Fixes: 0fae3bf018d9 ("mpls: handle device renames for per-device sysctls") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is because commit a41dad905e5a ("iov_iter: saner checks for attempt
to copy to/from iterator") has introduced sanity check for copying
from/to iov iterator. Lacking of copy direction from the iterator
viewpoint would lead to kernel stack trace like above.
This commit fixes this issue by initializing the iov iterator with
the correct copy direction when sending SYN or ACK without data.
syzbot found arm64 builds would crash in sock_recv_mark()
when CONFIG_HARDENED_USERCOPY=y
x86 and powerpc are not detecting the issue because
they define user_access_begin.
This will be handled in a different patch,
because a check_object_size() is missing.
Only data from skb->cb[] can be copied directly to/from user space,
as explained in commit 79a8a642bf05 ("net: Whitelist
the skbuff_head_cache "cb" field")
When setting 'snps,force_thresh_dma_mode' DT property, the following
warning is always emitted, regardless the status of force_sf_dma_mode:
dwmac-starfive 10020000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
Do not print the rather misleading message when DMA store and forward
mode is already disabled.
Fixes: e2a240c7d3bc ("driver:net:stmmac: Disable DMA store and forward mode if platform data force_thresh_dma_mode is set.") Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com> Link: https://lore.kernel.org/r/20230210202126.877548-1-cristian.ciocaltea@collabora.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In bnxt_reserve_rings(), there is logic to check that the number of TX
rings reserved is enough to cover all the mqprio TCs, but it fails to
account for the TX XDP rings. So the check will always fail if there
are mqprio TCs and TX XDP rings. As a result, the driver always fails
to initialize after the XDP program is attached and the device will be
brought down. A subsequent ifconfig up will also fail because the
number of TX rings is set to an inconsistent number. Fix the check to
properly account for TX XDP rings. If the check fails, set the number
of TX rings back to a consistent number after calling netdev_reset_tc().
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.") Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tc action act_ctinfo was using shared stats, fix it to use percpu stats
since bstats_update() must be called with locks or with a percpu pointer argument.
tdc results:
1..12
ok 1 c826 - Add ctinfo action with default setting
ok 2 0286 - Add ctinfo action with dscp
ok 3 4938 - Add ctinfo action with valid cpmark and zone
ok 4 7593 - Add ctinfo action with drop control
ok 5 2961 - Replace ctinfo action zone and action control
ok 6 e567 - Delete ctinfo action with valid index
ok 7 6a91 - Delete ctinfo action with invalid index
ok 8 5232 - List ctinfo actions
ok 9 7702 - Flush ctinfo actions
ok 10 3201 - Add ctinfo action with duplicate index
ok 11 8295 - Add ctinfo action with invalid index
ok 12 3964 - Replace ctinfo action with invalid goto_chain control
Fixes: 24ec483cec98 ("net: sched: Introduce act_ctinfo action") Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com> Link: https://lore.kernel.org/r/20230210200824.444856-1-pctammela@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported that act_len in kalmia_send_init_packet() is
uninitialized when passing it to the first usb_bulk_msg error path. Jiri
Pirko noted that it's pointless to pass it in the error path, and that
the value that would be printed in the second error path would be the
value of act_len from the first call to usb_bulk_msg.[1]
With this in mind, let's just not pass act_len to the usb_bulk_msg error
paths.
Eric Dumazet pointed out [0] that when we call skb_set_owner_r()
for ipv6_pinfo.pktoptions, sk_rmem_schedule() has not been called,
resulting in a negative sk_forward_alloc.
We add a new helper which clones a skb and sets its owner only
when sk_rmem_schedule() succeeds.
Note that we move skb_set_owner_r() forward in (dccp|tcp)_v6_do_rcv()
because tcp_send_synack() can make sk_forward_alloc negative before
ipv6_opt_accepted() in the crossed SYN-ACK or self-connect() cases.
The imperfect hash area can be updated while packets are traversing,
which will cause a use-after-free when 'tcf_exts_exec()' is called
with the destroyed tcf_ext.
CPU 0: CPU 1:
tcindex_set_parms tcindex_classify
tcindex_lookup
tcindex_lookup
tcf_exts_change
tcf_exts_exec [UAF]
Stop operating on the shared area directly, by using a local copy,
and update the filter with 'rcu_replace_pointer()'. Delete the old
filter version only after a rcu grace period elapsed.
Fixes: 9b0d4446b569 ("net: sched: avoid atomic swap in tcf_exts_change") Reported-by: valis <sec@valis.email> Suggested-by: valis <sec@valis.email> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Link: https://lore.kernel.org/r/20230209143739.279867-1-pctammela@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In TI's AM62x/AM64x SoCs, successful teardown of RX DMA Channel raises an
interrupt. The process of servicing this interrupt involves flushing all
pending RX DMA descriptors and clearing the teardown completion marker
(TDCM). The am65_cpsw_nuss_rx_packets() function invoked from the RX
NAPI callback services the interrupt. Thus, it is necessary to wait for
this handler to run, drain all packets and clear TDCM, before calling
napi_disable() in am65_cpsw_nuss_common_stop() function post channel
teardown. If napi_disable() executes before ensuring that TDCM is
cleared, the TDCM remains set when the interfaces are down, resulting in
an interrupt storm when the interfaces are brought up again.
Since the interrupt raised to indicate the RX DMA Channel teardown is
specific to the AM62x and AM64x SoCs, add a quirk for it.
Fixes: 4f7cce272403 ("net: ethernet: ti: am65-cpsw: add support for am64x cpsw3g") Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20230209084432.189222-1-s-vadapalli@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code blocks handling BCMA_CHIP_ID_BCM5357 and BCMA_CHIP_ID_BCM53572 were
incorrectly unified. Chip package values are not unique and cannot be
checked independently. They are meaningful only in a context of a given
chip.
Packages BCM5358 and BCM47188 share the same value but then belong to
different chips. Code unification resulted in treating BCM5358 as
BCM47188 and broke its initialization.
Link: https://github.com/openwrt/openwrt/issues/8278 Fixes: cb1b0f90acfe ("net: ethernet: bgmac: unify code of the same family") Cc: Jon Mason <jdmason@kudzu.us> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20230208091637.16291-1-zajec5@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the second VLAN HLEN into account when computing the maximum
MTU size as other drivers do.
Fixes: 0c8493d90b6b ("i40e: add XDP support for pass and drop actions") Signed-off-by: Jason Xing <kernelxing@tencent.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently I encountered one case where I cannot increase the MTU size
directly from 1500 to a much bigger value with XDP enabled if the
server is equipped with IXGBE card, which happened on thousands of
servers in production environment. After applying the current patch,
we can set the maximum MTU size to 3K.
This patch follows the behavior of changing MTU as i40e/ice does.
References:
[1] commit 23b44513c3e6 ("ice: allow 3k MTU for XDP")
[2] commit 0c8493d90b6b ("i40e: add XDP support for pass and drop actions")
Fixes: fabf1bce103a ("ixgbe: Prevent unsupported configurations with XDP") Signed-off-by: Jason Xing <kernelxing@tencent.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a problem reported to us where the addition of a VF with an IPv6
address ending with a particular sequence would cause the parent device on
the PF to no longer be able to respond to neighbor discovery packets.
In this case, we had an ovs-bridge device living on top of a VLAN, which
was on top of a PF, and it would not be able to talk anymore (the neighbor
entry would expire and couldn't be restored).
The root cause of the issue is that if the PF is asked to be in IFF_PROMISC
mode (promiscuous mode) and it had an ipv6 address that needed the
33:33:ff:00:00:04 multicast address to work, then when the VF was added
with the need for the same multicast address, the VF would steal all the
traffic destined for that address.
The ice driver didn't auto-subscribe a request of IFF_PROMISC to the
"multicast replication from other port's traffic" meaning that it won't get
for instance, packets with an exact destination in the VF, as above.
The VF's IPv6 address, which adds a "perfect filter" for 33:33:ff:00:00:04,
results in no packets for that multicast address making it to the PF (which
is in promisc but NOT "multicast replication").
The fix is to enable "multicast promiscuous" whenever the driver is asked
to enable IFF_PROMISC, and make sure to disable it when appropriate.
The UNSLICE_UNIT_LEVEL_CLKGATE register programmed by this workaround
has 'BUS' style reset, indicating that it does not lose its value on
engine resets. Furthermore, this register is part of the GT forcewake
domain rather than the RENDER domain, so it should not be impacted by
RCS engine resets. As such, we should implement this on the GT
workaround list rather than an engine list.
YUV images can either be presented as one allocation with offsets
for the different planes, or multiple allocations with 0 offsets.
The driver only ever calls drm_fb_[dma|cma]_get_gem_obj with plane
index 0, therefore any application using the second approach was
incorrectly rendered.
Correctly determine the address for each plane, removing the
assumption that the base address is the same for each.
The formula that determines the core clock requirement based on pixel
clock and blanking has been determined experimentally to minimise the
clock while supporting all modes we've seen.
A new reduced blanking mode (4kp60 at 533MHz rather than the standard
594MHz) has been seen that doesn't produce a high enough clock and
results in "flip_done timed out" error.
Increase the setup cost in the formula to make this work. The result is
a reduced blanking mode increases by up to 7MHz while leaving the
standard timing
mode untouched
When converting net_device_stats to rtnl_link_stats64 sign extension
is triggered on ILP32 machines as 6c1c509778 changed the previous
"ulong -> u64" conversion to "long -> u64" by accessing the
net_device_stats fields through a (signed) atomic_long_t.
This causes for example the received bytes counter to jump to 16EiB after
having received 2^31 bytes. Casting the atomic value to "unsigned long"
beforehand converting it into u64 avoids this.
Fixes: 6c1c5097781f ("net: add atomic_long_t to net_device_stats fields") Signed-off-by: Felix Riemann <felix.riemann@sma.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pages being freed by memblock_free_late() have already been
initialized, but if they are in the deferred init range,
__free_one_page() might access nearby uninitialized pages when trying to
coalesce buddies. This can, for example, trigger this BUG:
BUG: unable to handle page fault for address: ffffe964c02580c8
RIP: 0010:__list_del_entry_valid+0x3f/0x70
<TASK>
__free_one_page+0x139/0x410
__free_pages_ok+0x21d/0x450
memblock_free_late+0x8c/0xb9
efi_free_boot_services+0x16b/0x25c
efi_enter_virtual_mode+0x403/0x446
start_kernel+0x678/0x714
secondary_startup_64_no_verify+0xd2/0xdb
</TASK>
A proper fix will be more involved so revert this change for the time
being.
Fixes: 115d9d77bb0f ("mm: Always release pages to the buddy allocator in memblock_free_late().") Signed-off-by: Aaron Thompson <dev@aaront.org> Link: https://lore.kernel.org/r/20230207082151.1303-1-dev@aaront.org Signed-off-by: Mike Rapoport (IBM) <rppt@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fs/coredump.c:835:12: error: ‘dump_emit_page’ defined but not used [-Werror=unused-function]
835 | static int dump_emit_page(struct coredump_params *cprm, struct page *page)
| ^~~~~~~~~~~~~~
Fix this by moving dump_emit_page() inside the existing section
protected by #ifdef CONFIG_ELF_CORE.
Fixes: 06bbaa6dc53cb720 ("[coredump] don't use __kernel_write() on kmap_local_page()") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tetsuo-San noted that commit f5d39b020809 ("freezer,sched: Rewrite
core freezer logic") broke call_usermodehelper_exec() for the KILLABLE
case.
Specifically it was missed that the second, unconditional,
wait_for_completion() was not optional and ensures the on-stack
completion is unused before going out-of-scope.
Nick Bowler reported another sparc64 breakage after the young/dirty
persistent work for page migration (per "Link:" below). That's after a
similar report [2].
It turns out page migration was overlooked, and it wasn't failing before
because page migration was not enabled in the initial report test
environment.
David proposed another way [2] to fix this from sparc64 side, but that
patch didn't land somehow. Neither did I check whether there's any other
arch that has similar issues.
Let's fix it for now as simple as moving the write bit handling to be
after dirty, like what we did before.
Note: this is based on mm-unstable, because the breakage was since 6.1 and
we're at a very late stage of 6.2 (-rc8), so I assume for this specific
case we should target this at 6.3.
I was running traces of the read code against an RAID storage system to
understand why read requests were being misaligned against the underlying
RAID strips. I found that the page end offset calculation in
filemap_get_read_batch() was off by one.
When a read is submitted with end offset 1048575, then it calculates the
end page for read of 256 when it should be 255. "last_index" is the index
of the page beyond the end of the read and it should be skipped when get a
batch of pages for read in @filemap_get_read_batch().
The below simple patch fixes the problem. This code was introduced in
kernel 5.12.
Link: https://lkml.kernel.org/r/20230208022400.28962-1-coolqyj@163.com Fixes: cbd59c48ae2b ("mm/filemap: use head pages in generic_file_buffered_read") Signed-off-by: Qian Yingjin <qian@ddn.com> Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During collapse, in a few places we check to see if a given small page has
any unaccounted references. If the refcount on the page doesn't match our
expectations, it must be there is an unknown user concurrently interested
in the page, and so it's not safe to move the contents elsewhere.
However, the unaccounted pins are likely an ephemeral state.
In this situation, MADV_COLLAPSE returns -EINVAL when it should return
-EAGAIN. This could cause userspace to conclude that the syscall
failed, when it in fact could succeed by retrying.
Macro NILFS_SB2_OFFSET_BYTES, which computes the position of the second
superblock, underflows when the argument device size is less than 4096
bytes. Therefore, when using this macro, it is necessary to check in
advance that the device size is not less than a lower limit, or at least
that underflow does not occur.
The current nilfs2 implementation lacks this check, causing out-of-bound
block access when mounting devices smaller than 4096 bytes:
I/O error, dev loop0, sector 36028797018963960 op 0x0:(READ) flags 0x0
phys_seg 1 prio class 2
NILFS (loop0): unable to read secondary superblock (blocksize = 1024)
In addition, when trying to resize the filesystem to a size below 4096
bytes, this underflow occurs in nilfs_resize_fs(), passing a huge number
of segments to nilfs_sufile_resize(), corrupting parameters such as the
number of segments in superblocks. This causes excessive loop iterations
in nilfs_sufile_resize() during a subsequent resize ioctl, causing
semaphore ns_segctor_sem to block for a long time and hang the writer
thread:
Users can specify the hugetlb page size in the mmap, shmget and
memfd_create system calls. This is done by using 6 bits within the flags
argument to encode the base-2 logarithm of the desired page size. The
routine hstate_sizelog() uses the log2 value to find the corresponding
hugetlb hstate structure. Converting the log2 value (page_size_log) to
potential hugetlb page size is the simple statement:
1UL << page_size_log
Because only 6 bits are used for page_size_log, the left shift can not be
greater than 63. This is fine on 64 bit architectures where a long is 64
bits. However, if a value greater than 31 is passed on a 32 bit
architecture (where long is 32 bits) the shift will result in undefined
behavior. This was generally not an issue as the result of the undefined
shift had to exactly match hugetlb page size to proceed.
Recent improvements in runtime checking have resulted in this undefined
behavior throwing errors such as reported below.
Fix by comparing page_size_log to BITS_PER_LONG before doing shift.
Link: https://lkml.kernel.org/r/20230216013542.138708-1-mike.kravetz@oracle.com Link: https://lore.kernel.org/lkml/CA+G9fYuei_Tr-vN9GS7SfFyU1y9hNysnf=PB7kT0=yv4MiPgVg@mail.gmail.com/ Fixes: 42d7395feb56 ("mm: support more pagesizes for MAP_HUGETLB/SHM_HUGETLB") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Reviewed-by: Jesper Juhl <jesperjuhl76@gmail.com> Acked-by: Muchun Song <songmuchun@bytedance.com> Tested-by: Linux Kernel Functional Testing <lkft@linaro.org> Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Anders Roxell <anders.roxell@linaro.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Sasha Levin <sashal@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a non-root cgroup gets removed when there is a thread that registered
trigger and is polling on a pressure file within the cgroup, the polling
waitqueue gets freed in the following path:
The fundamental problem here is that cgroup_file_release() (and
consequently waitqueue's lifetime) is not tied to the file's real lifetime.
Using wake_up_pollfree() here might be less than ideal, but it is in line
with the comment at commit 42288cb44c4b ("wait: add wake_up_pollfree()")
since the waitqueue's lifetime is not tied to file's one and can be
considered as another special case. While this would be fixable by somehow
making cgroup_file_release() be tied to the fput(), it would require
sizable refactoring at cgroups or higher layer which might be more
justifiable if we identify more cases like this.
BUG: KASAN: use-after-free in _raw_spin_lock_irqsave+0x60/0xc0
Write of size 4 at addr ffff88810e625328 by task a.out/4404
Since this was seen previously with SSD 840 EVO drives in
https://bugzilla.kernel.org/show_bug.cgi?id=203475 let's add the same
fix for these drives as the EVOs have, since they likely have very
similar firmwares.
Signed-off-by: Patrick McLean <chutzpah@gentoo.org> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark the Tiger Lake UP{3,4} AHCI controller as "low_power". This enables
S0ix to work out of the box. Otherwise this isn't working unless the
user manually sets /sys/class/scsi_host/*/link_power_management_policy.
Intel lists a total of 4 SATA controller IDs in [1] for those mobile
PCHs. This commit just adds the "AHCI" variant since I only tested
those.
Signed-off-by: Simon Gaiser <simon@invisiblethingslab.com> CC: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f2bd1c5ae2cb ("ALSA: hda: Fix page fault in
snd_hda_codec_shutdown()") relocated initialization of several codec
device fields. Due to differences between codec_exec_verb() and
snd_hdac_bus_exec_bus() in how they handle VERB execution - the latter
does not touch PM - assigning ->exec_verb to codec_exec_verb() causes PM
to be engaged before it is configured for the device. Configuration of
PM for the ASoC HDAudio sound card is done with snd_hda_set_power_save()
during skl_hda_audio_probe() whereas the assignment happens early, in
snd_hda_codec_device_init().
Revert to previous behavior to avoid problems caused by too early PM
manipulation.
If mmc_add_host() fails, it doesn't need to call mmc_remove_host(),
or it will cause null-ptr-deref, because of deleting a not added
device in mmc_remove_host().
To fix this, goto label 'fail_glue_init', if mmc_add_host() fails,
and change the label 'fail_add_host' to 'fail_gpiod_request'.
If sdio_add_func() or sdio_init_func() fails, sdio_remove_func() can
not release the resources, because the sdio function is not presented
in these two cases, it won't call of_node_put() or put_device().
To fix these leaks, make sdio_func_present() only control whether
device_del() needs to be called or not, then always call of_node_put()
and put_device().
In error case in sdio_init_func(), the reference of 'card->dev' is
not get, to avoid redundant put in sdio_free_func_cis(), move the
get_device() to sdio_alloc_func() and put_device() to sdio_release_func(),
it can keep the get/put function be balanced.
Without this patch, while doing fault inject test, it can get the
following leak reports, after this fix, the leak is gone.
Some SDIO WiFi modules stopped working after SDIO interrupt mode
was added if cap_sdio_irq isn't set in device tree. This patch was
confirmed to fix the issue.
v3: Fix vmw_user_bo_lookup which was also dropping the gem reference
before the kernel was done with buffer depending on userspace doing
the right thing. Same bug, different spot.
It is possible for userspace to predict the next buffer handle and
to destroy the buffer while it's still used by the kernel. Delay
dropping the internal reference on the buffers until kernel is done
with them.
Instead of immediately dropping the gem reference in vmw_user_bo_lookup
and vmw_gem_object_create_with_handle let the callers decide when they're
ready give the control back to userspace.
Also fixes the second usage of vmw_gem_object_create_with_handle in
vmwgfx_surface.c which wasn't grabbing an explicit reference
to the gem object which could have been destroyed by the userspace
on the owning surface at any point.
ttm_bo_init_reserved on failure puts the buffer object back which
causes it to be deleted, but kfree was still being called on the same
buffer in vmw_bo_create leading to a double free.
After the double free the vmw_gem_object_create_with_handle was
setting the gem function objects before checking the return status
of vmw_bo_create leading to null pointer access.
Fix the entire path by relaying on ttm_bo_init_reserved to delete the
buffer objects on failure and making sure the return status is checked
before setting the gem function objects on the buffer object.
CONFIG_DRM_USE_DYNAMIC_DEBUG breaks debug prints for (at least modular)
drm drivers. The debug prints can be reinstated by manually frobbing
/sys/module/drm/parameters/debug after the fact, but at that point the
damage is done and all debugs from driver probe are lost. This makes
drivers totally undebuggable.
There's a more complete fix in progress [1], with further details, but
we need this fixed in stable kernels. Mark the feature as broken and
disable it by default, with hopes distros follow suit and disable it as
well.
When a fbdev with deferred I/O is once opened and closed, the dirty
pages still remain queued in the pageref list, and eventually later
those may be processed in the delayed work. This may lead to a
corruption of pages, hitting an Oops.
This patch makes sure to cancel the delayed work and clean up the
pageref list at closing the device for addressing the bug. A part of
the cleanup code is factored out as a new helper function that is
called from the common fb_release().
Commit b3973bb40041 ("vmxnet3: set correct hash type based on
rss information") added hashType information into skb. However,
rssType field is populated for eop descriptor. This can lead
to incorrectly reporting of hashType for packets which use
multiple rx descriptors. Multiple rx descriptors are used
for Jumbo frame or LRO packets, which can hit this issue.
This patch moves the RSS codeblock under eop descritor.
Cc: stable@vger.kernel.org Fixes: b3973bb40041 ("vmxnet3: set correct hash type based on rss information") Signed-off-by: Ronak Doshi <doshir@vmware.com> Acked-by: Peng Li <lpeng@vmware.com> Acked-by: Guolin Yang <gyang@vmware.com> Link: https://lore.kernel.org/r/20230208223900.5794-1-doshir@vmware.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e4a0d3e720e7 ("aio: Make it possible to remap aio ring") introduced
a null-deref if mremap is called on an old aio mapping after fork as
mm->ioctx_table will be set to NULL.
[jmoyer@redhat.com: fix 80 column issue] Link: https://lkml.kernel.org/r/x49sffq4nvg.fsf@segfault.boston.devel.redhat.com Fixes: e4a0d3e720e7 ("aio: Make it possible to remap aio ring") Signed-off-by: Seth Jenkins <sethjenkins@google.com> Signed-off-by: Jeff Moyer <jmoyer@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Jann Horn <jannh@google.com> Cc: Pavel Emelyanov <xemul@parallels.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugfs_remove_recursive() is invoked by unregister_shrinker(), which
is holding the write lock of shrinker_rwsem. It will waits for the
handler of debugfs file complete. The handler also needs to hold the read
lock of shrinker_rwsem to do something. So it may cause the following
deadlock:
unregister_shrinker()
--> down_write(&shrinker_rwsem);
debugfs_remove_recursive()
// wait for (A)
--> wait_for_completion();
// wait for (B)
--> down_read_killable(&shrinker_rwsem)
debugfs_file_put() -- (A)
up_write() -- (B)
The down_read_killable() can be killed, so that the above deadlock can be
recovered. But it still requires an extra kill action, otherwise it will
block all subsequent shrinker-related operations, so it's better to fix
it.
[akpm@linux-foundation.org: fix CONFIG_SHRINKER_DEBUG=n stub] Link: https://lkml.kernel.org/r/20230202105612.64641-1-zhengqi.arch@bytedance.com Fixes: 5035ebc644ae ("mm: shrinkers: introduce debugfs interface for memory shrinkers") Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com> Reviewed-by: Roman Gushchin <roman.gushchin@linux.dev> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On powerpc64, you can build a kernel with KASAN as soon as you build it
with RADIX MMU support. However if the CPU doesn't have RADIX MMU, KASAN
isn't enabled at init and the following Oops is encountered.
[ 0.000000][ T0] KASAN not enabled as it requires radix!
The Oops is due to kasan_byte_accessible() not checking the readiness of
KASAN. Add missing call to kasan_arch_is_ready() and bail out when not
ready. The same problem is observed with ____kasan_kfree_large() so fix
it the same.
Also, as KASAN is not available and no shadow area is allocated for linear
memory mapping, there is no point in allocating shadow mem for vmalloc
memory as shown below in /sys/kernel/debug/kernel_page_tables
---[ kasan shadow mem start ]---
0xc00f000000000000-0xc00f00000006ffff 0x00000000040f0000 448K r w pte valid present dirty accessed
0xc00f000000860000-0xc00f00000086ffff 0x000000000ac10000 64K r w pte valid present dirty accessed
0xc00f3ffffffe0000-0xc00f3fffffffffff 0x0000000004d10000 128K r w pte valid present dirty accessed
---[ kasan shadow mem end ]---
So, also verify KASAN readiness before allocating and poisoning
shadow mem for VMAs.
a crash is encountered when kmemleak starts to scan the list of gray
or allocated objects that it maintains. Upon closer inspection, it was
observed that these page-faults always occurred when kmemleak attempted
to scan a CMA region.
At the moment, kmemleak is made aware of CMA regions that are specified
through the devicetree to be dynamically allocated within a range of
addresses. However, kmemleak should not need to scan CMA regions or any
reserved memory region, as those regions can be used for DMA transfers
between drivers and peripherals, and thus wouldn't contain anything
useful for kmemleak.
Additionally, since CMA regions are unmapped from the kernel's address
space when they are freed to the buddy allocator at boot when
CONFIG_DEBUG_PAGEALLOC is enabled, kmemleak shouldn't attempt to access
those memory regions, as that will trigger a crash. Thus, kmemleak
should ignore all dynamically allocated reserved memory regions.
This patch (of 1):
Currently, kmemleak ignores dynamically allocated reserved memory regions
that don't have a kernel mapping. However, regions that do retain a
kernel mapping (e.g. CMA regions) do get scanned by kmemleak.
This is not ideal for two reasons:
1 kmemleak works by scanning memory regions for pointers to allocated
objects to determine if those objects have been leaked or not.
However, reserved memory regions can be used between drivers and
peripherals for DMA transfers, and thus, would not contain pointers to
allocated objects, making it unnecessary for kmemleak to scan these
reserved memory regions.
2 When CONFIG_DEBUG_PAGEALLOC is enabled, along with kmemleak, the
CMA reserved memory regions are unmapped from the kernel's address
space when they are freed to buddy at boot. These CMA reserved regions
are still tracked by kmemleak, however, and when kmemleak attempts to
scan them, a crash will happen, as accessing the CMA region will result
in a page-fault, since the regions are unmapped.
Thus, use kmemleak_ignore_phys() for all dynamically allocated reserved
memory regions, instead of those that do not have a kernel mapping
associated with them.
Link: https://lkml.kernel.org/r/20230208232001.2052777-1-isaacmanjarres@google.com Link: https://lkml.kernel.org/r/20230208232001.2052777-2-isaacmanjarres@google.com Fixes: a7259df76702 ("memblock: make memblock_find_in_range method private") Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com> Acked-by: Mike Rapoport (IBM) <rppt@kernel.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: Frank Rowand <frowand.list@gmail.com> Cc: Kirill A. Shutemov <kirill.shtuemov@linux.intel.com> Cc: Nick Kossifidis <mick@ics.forth.gr> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Rob Herring <robh@kernel.org> Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Cc: Saravana Kannan <saravanak@google.com> Cc: <stable@vger.kernel.org> [5.15+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matthieu Baerts [Tue, 14 Feb 2023 16:05:10 +0000 (17:05 +0100)]
selftests: mptcp: userspace: fix v4-v6 test in v6.1
The commit 4656d72c1efa ("selftests: mptcp: userspace: validate v4-v6 subflows mix")
has been backported to v6.1.8 without any conflicts. But it looks like
it was depending on a previous one:
commit 1cc94ac1af4b ("selftests: mptcp: make evts global in userspace_pm")
Without it, the test fails with:
./userspace_pm.sh: line 788: : No such file or directory
# ADD_ADDR4 id:14 10.0.2.1 (ns1) => ns2, reuse port [FAIL]
sed: can't read : No such file or directory
This dependence refactors the way the monitoring files are being
created: only once for all the different sub-tests instead of per
sub-test.
It is probably better to avoid backporting the refactoring. That is why
the new sub-test has been adapted to work using the previous way that is
still in place here in v6.1: the monitoring is started at the beginning
of each sub-test and the created file is removed at the end.
When received corrupted snap trace we don't know what exactly has
happened in MDS side. And we shouldn't continue IOs and metadatas
access to MDS, which may corrupt or get incorrect contents.
This patch will just block all the further IO/MDS requests
immediately and then evict the kclient itself.
The reason why we still need to evict the kclient just after
blocking all the further IOs is that the MDS could revoke the caps
faster.
There could be boards with DCN listed in IP discovery, but no
display hardware actually wired up. In this case the vbios
display table will not be populated. Detect this case and
skip loading DM when we detect it.
v2: Mark DCN as harvested as well so other display checks
elsewhere in the driver are handled properly.
[Why]
Otherwise we can be out of sync with what's in the hardware, leading
to us rerunning every command that's presently in the ringbuffer.
[How]
Reset software state for the mailboxes in hw_reset callback.
This is already done as part of the mailbox init in hw_init, but we
do need to remember to reset the last cached wptr value as well here.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The hwss function does_plane_fit_in_mall not applicable to dcn3.2 asics.
Using it with dcn3.2 can result in undefined behaviour.
[How]
Assign the function pointer to NULL.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: George Shen <george.shen@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Lower max_downscale_ratio and ARGB888 downscale factor
to prevent cases where underflow may occur on dcn314
[How]
Set max_downscale_ratio to 400 and ARGB downscale factor
to 250 for dcn314
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Daniel Miess <Daniel.Miess@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Brackets missing in the calculation for MIN_DST_Y_NEXT_START
[How]
Add missing brackets for this calculation
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Daniel Miess <Daniel.Miess@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If nvme_alloc_admin_tag_set() fails, the admin_q and fabrics_q pointers
are left with an invalid, non-NULL value. Other functions may then check
the pointers and dereference them, e.g. in
As part of nvmet_fc_ls_create_association there is a case where
nvmet_fc_alloc_target_queue fails right after a new association with an
admin queue is created. In this case, no one releases the get taken in
nvmet_fc_alloc_target_assoc. This fix is adding the missing put.
Signed-off-by: Amit Engel <Amit.Engel@dell.com> Reviewed-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Historically calls to __decompress() didn't specify "out_len" parameter
on many architectures including s390, expecting that no writes beyond
uncompressed kernel image are performed. This has changed since commit 2aa14b1ab2c4 ("zstd: import usptream v1.5.2") which includes zstd library
commit 6a7ede3dfccb ("Reduce size of dctx by reutilizing dst buffer
(#2751)"). Now zstd decompression code might store literal buffer in
the unwritten portion of the destination buffer. Since "out_len" is
not set, it is considered to be unlimited and hence free to use for
optimization needs. On s390 this might corrupt initrd or ipl report
which are often placed right after the decompressor buffer. Luckily the
size of uncompressed kernel image is already known to the decompressor,
so to avoid the problem simply specify it in the "out_len" parameter.
There doesn't appear to be a reason to truncate the allocation used for
flow_info, so do a full allocation and remove the unused empty struct.
GCC does not like having a reference to an object that has been
partially allocated, as bounds checking may become impossible when
such an object is passed to other code. Seen with GCC 13:
../drivers/net/ethernet/mediatek/mtk_ppe.c: In function 'mtk_foe_entry_commit_subflow':
../drivers/net/ethernet/mediatek/mtk_ppe.c:623:18: warning: array subscript 'struct mtk_flow_entry[0]' is partly outside array bounds of 'unsigned char[48]' [-Warray-bounds=]
623 | flow_info->l2_data.base_flow = entry;
| ^~
Cc: Felix Fietkau <nbd@nbd.name> Cc: John Crispin <john@phrozen.org> Cc: Sean Wang <sean.wang@mediatek.com> Cc: Mark Lee <Mark-MC.Lee@mediatek.com> Cc: Lorenzo Bianconi <lorenzo@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: netdev@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-mediatek@lists.infradead.org Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230127223853.never.014-kees@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Starting from Turing, the driver is no longer responsible for initiating
DEVINIT when required as the GPU started loading a FW image from ROM and
executing DEVINIT itself after power-on.
However - we apparently still need to wait for it to complete.
This should correct some issues with runpm on some systems, where we get
control of the HW before it's been fully reinitialised after resume from
suspend.
fscache_create_volume_work() uses wake_up_bit() to wake up the processes
which are waiting for the completion of volume creation. According to
comments in wake_up_bit() and waitqueue_active(), an extra smp_mb() is
needed to guarantee the memory order between FSCACHE_VOLUME_CREATING
flag and waitqueue_active() before invoking wake_up_bit().
Fixing it by using clear_and_wake_up_bit() to add the missing memory
barrier.
Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com> Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Link: https://lore.kernel.org/r/20230113115211.2895845-3-houtao@huaweicloud.com/ Signed-off-by: Sasha Levin <sashal@kernel.org>
Interrupt entry sets the soft mask to IRQS_ALL_DISABLED to match the
hard irq disabled state. So when should_hard_irq_enable() returns true
because we want PMI interrupts in irq handlers, MSR[EE] is enabled but
PMIs just get soft-masked. Fix this by clearing IRQS_PMI_DISABLED before
enabling MSR[EE].
This also tidies some of the warnings, no need to duplicate them in
both should_hard_irq_enable() and do_hard_irq_enable().
Currently in phy_init_eee() the driver unconditionally configures the PHY
to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt
storm on my qcs404-base board.
Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible
device RX_CLK continues to run even in Rx LPI state.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
"tcpdump" is used to capture traffic in these tests while using a random,
temporary and not suffixed file for it. This can interfere with apparmor
configuration where the tool is only allowed to read from files with
'known' extensions.
The MINE type application/vnd.tcpdump.pcap was registered with IANA for
pcap files and .pcap is the extension that is both most common but also
aligned with standard apparmor configurations. See TCPDUMP(8) for more
details.
This improves compatibility with standard apparmor configurations by
using ".pcap" as the file extension for the tests' temporary files.
Signed-off-by: Andrei Gherzan <andrei.gherzan@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If you call listen() and accept() on an already connect()ed
rose socket, accept() can successfully connect.
This is because when the peer socket sends data to sendmsg,
the skb with its own sk stored in the connected socket's
sk->sk_receive_queue is connected, and rose_accept() dequeues
the skb waiting in the sk->sk_receive_queue.
This creates a child socket with the sk of the parent
rose socket, which can cause confusion.
Fix rose_listen() to return -EINVAL if the socket has
already been successfully connected, and add lock_sock
to prevent this issue.
Signed-off-by: Hyunwoo Kim <v4bel@theori.io> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20230125105944.GA133314@ubuntu Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ifcvf_mgmt_dev leaks memory if it is not freed before
returning. Call is made to correct return statement
so memory does not leak. ifcvf_init_hw does not take
care of this so it is needed to do it here.
Signed-off-by: Tanmay Bhushan <007047221b@gmail.com>
Message-Id: <772e9fe133f21fa78fb98a2ebe8969efbbd58e3c.camel@gmail.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Zhu Lingshan <lingshan.zhu@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log