We used to access the dtb via its linear mapping address but now that the
dtb early mapping was moved in the fixmap region, we can keep using this
address since it is present in swapper_pg_dir, and remove the dtb
relocation.
Note that the relocation was wrong anyway since early_memremap() is
restricted to 256K whereas the maximum fdt size is 2MB.
early_init_dt_verify() is already called in parse_dtb() and since the dtb
address does not change anymore (it is now in the fixmap region), no need
to reset initial_boot_params by calling early_init_dt_verify() again.
- early_pg_dir maps the kernel which allows to discover the system
memory
- swapper_pg_dir installs the final mapping (linear mapping included)
We used to map the dtb in early_pg_dir using DTB_EARLY_BASE_VA, and this
mapping was not carried over in swapper_pg_dir. It happens that
early_init_fdt_scan_reserved_mem() must be called before swapper_pg_dir is
setup otherwise we could allocate reserved memory defined in the dtb.
And this function initializes reserved_mem variable with addresses that
lie in the early_pg_dir dtb mapping: when those addresses are reused
with swapper_pg_dir, this mapping does not exist and then we trap.
The previous "fix" was incorrect as early_init_fdt_scan_reserved_mem()
must be called before swapper_pg_dir is set up otherwise we could
allocate in reserved memory defined in the dtb.
So move the dtb mapping in the fixmap region which is established in
early_pg_dir and handed over to swapper_pg_dir.
This patch had to be backported because:
- the documentation for sv57 is not present here (as sv48/57 are not
present)
Don't require the use of dynamic debug (or modification of the kernel to
add a #define DEBUG to the top of this file) to get the printk message
about driver probe timing. This printk is only emitted when
initcall_debug is enabled on the kernel commandline, and it isn't
immediately obvious that you have to do something else to debug boot
timing issues related to driver probe. Add a comment too so it doesn't
get converted back to pr_debug().
Fixes: eb7fbc9fb118 ("driver core: Add missing '\n' in log messages") Cc: stable <stable@kernel.org> Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Brian Norris <briannorris@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20230412225842.3196599-1-swboyd@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add UNISOC vendor ID and TOZED LT70-C modem which is based from UNISOC
SL8563. The modem supports the NCM mode. Interface 0 is used for running
the AT commands. Interface 12 is the ADB interface.
There are some warnings on older compilers (gcc 10, 7) or non-x86_64
architectures (aarch64). As btrfs wants to enable -Wmaybe-uninitialized
by default, fix the warnings even though it's not necessary on recent
compilers (gcc 12+).
../fs/btrfs/volumes.c: In function ‘btrfs_init_new_device’:
../fs/btrfs/volumes.c:2703:3: error: ‘seed_devices’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
2703 | btrfs_setup_sprout(fs_info, seed_devices);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../fs/btrfs/send.c: In function ‘get_cur_inode_state’:
../include/linux/compiler.h:70:32: error: ‘right_gen’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
70 | (__if_trace.miss_hit[1]++,1) : \
| ^
../fs/btrfs/send.c:1878:6: note: ‘right_gen’ was declared here
1878 | u64 right_gen;
| ^~~~~~~~~
Previously, capability was checked using capable(), which verified that the
caller of the ioctl system call had the required capability. In addition,
the result of the check would be stored in the HCI_SOCK_TRUSTED flag,
making it persistent for the socket.
However, malicious programs can abuse this approach by deliberately sharing
an HCI socket with a privileged task. The HCI socket will be marked as
trusted when the privileged task occasionally makes an ioctl call.
This problem can be solved by using sk_capable() to check capability, which
ensures that not only the current task but also the socket opener has the
specified capability, thus reducing the risk of privilege escalation
through the previously identified vulnerability.
Cc: stable@vger.kernel.org Fixes: f81f5b2db869 ("Bluetooth: Send control open and close messages for HCI raw sockets") Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1796f808e4bb ("HID: i2c-hid: acpi: Stop setting wakeup_capable")
changed the policy such that I2C touchpads may be able to wake up the
system by default if the system is configured as such.
However on Clevo NL5xNU there is a mistake in the ACPI tables that the
TP_ATTN# signal connected to GPIO 9 is configured as ActiveLow and level
triggered but connected to a pull up. As soon as the system suspends the
touchpad loses power and then the system wakes up.
To avoid this problem, introduce a quirk for this model that will prevent
the wakeup capability for being set for GPIO 9.
This patch is analoge to a very similar patch for NL5xRU, just the DMI
string changed.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Cc: stable@vger.kernel.org Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers are supposed to fix this up if needed if they don't outright
reject it. Uncovered by 6c11df58fd1a ("fbmem: Check virtual screen
sizes in fb_set_var()").
Fix a slab-out-of-bounds read that occurs in kmemdup() called from
brcmf_get_assoc_ies().
The bug could occur when assoc_info->req_len, data from a URB provided
by a USB device, is bigger than the size of buffer which is defined as
WL_EXTRA_BUF_MAX.
Add the size check for req_len/resp_len of assoc_info.
Found by a modified version of syzkaller.
[ 46.592467][ T7] ==================================================================
[ 46.594687][ T7] BUG: KASAN: slab-out-of-bounds in kmemdup+0x3e/0x50
[ 46.596572][ T7] Read of size 3014656 at addr ffff888019442000 by task kworker/0:1/7
[ 46.598575][ T7]
[ 46.599157][ T7] CPU: 0 PID: 7 Comm: kworker/0:1 Tainted: G O 5.14.0+ #145
[ 46.601333][ T7] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 46.604360][ T7] Workqueue: events brcmf_fweh_event_worker
[ 46.605943][ T7] Call Trace:
[ 46.606584][ T7] dump_stack_lvl+0x8e/0xd1
[ 46.607446][ T7] print_address_description.constprop.0.cold+0x93/0x334
[ 46.608610][ T7] ? kmemdup+0x3e/0x50
[ 46.609341][ T7] kasan_report.cold+0x79/0xd5
[ 46.610151][ T7] ? kmemdup+0x3e/0x50
[ 46.610796][ T7] kasan_check_range+0x14e/0x1b0
[ 46.611691][ T7] memcpy+0x20/0x60
[ 46.612323][ T7] kmemdup+0x3e/0x50
[ 46.612987][ T7] brcmf_get_assoc_ies+0x967/0xf60
[ 46.613904][ T7] ? brcmf_notify_vif_event+0x3d0/0x3d0
[ 46.614831][ T7] ? lock_chain_count+0x20/0x20
[ 46.615683][ T7] ? mark_lock.part.0+0xfc/0x2770
[ 46.616552][ T7] ? lock_chain_count+0x20/0x20
[ 46.617409][ T7] ? mark_lock.part.0+0xfc/0x2770
[ 46.618244][ T7] ? lock_chain_count+0x20/0x20
[ 46.619024][ T7] brcmf_bss_connect_done.constprop.0+0x241/0x2e0
[ 46.620019][ T7] ? brcmf_parse_configure_security.isra.0+0x2a0/0x2a0
[ 46.620818][ T7] ? __lock_acquire+0x181f/0x5790
[ 46.621462][ T7] brcmf_notify_connect_status+0x448/0x1950
[ 46.622134][ T7] ? rcu_read_lock_bh_held+0xb0/0xb0
[ 46.622736][ T7] ? brcmf_cfg80211_join_ibss+0x7b0/0x7b0
[ 46.623390][ T7] ? find_held_lock+0x2d/0x110
[ 46.623962][ T7] ? brcmf_fweh_event_worker+0x19f/0xc60
[ 46.624603][ T7] ? mark_held_locks+0x9f/0xe0
[ 46.625145][ T7] ? lockdep_hardirqs_on_prepare+0x3e0/0x3e0
[ 46.625871][ T7] ? brcmf_cfg80211_join_ibss+0x7b0/0x7b0
[ 46.626545][ T7] brcmf_fweh_call_event_handler.isra.0+0x90/0x100
[ 46.627338][ T7] brcmf_fweh_event_worker+0x557/0xc60
[ 46.627962][ T7] ? brcmf_fweh_call_event_handler.isra.0+0x100/0x100
[ 46.628736][ T7] ? rcu_read_lock_sched_held+0xa1/0xd0
[ 46.629396][ T7] ? rcu_read_lock_bh_held+0xb0/0xb0
[ 46.629970][ T7] ? lockdep_hardirqs_on_prepare+0x273/0x3e0
[ 46.630649][ T7] process_one_work+0x92b/0x1460
[ 46.631205][ T7] ? pwq_dec_nr_in_flight+0x330/0x330
[ 46.631821][ T7] ? rwlock_bug.part.0+0x90/0x90
[ 46.632347][ T7] worker_thread+0x95/0xe00
[ 46.632832][ T7] ? __kthread_parkme+0x115/0x1e0
[ 46.633393][ T7] ? process_one_work+0x1460/0x1460
[ 46.633957][ T7] kthread+0x3a1/0x480
[ 46.634369][ T7] ? set_kthread_struct+0x120/0x120
[ 46.634933][ T7] ret_from_fork+0x1f/0x30
[ 46.635431][ T7]
[ 46.635687][ T7] Allocated by task 7:
[ 46.636151][ T7] kasan_save_stack+0x1b/0x40
[ 46.636628][ T7] __kasan_kmalloc+0x7c/0x90
[ 46.637108][ T7] kmem_cache_alloc_trace+0x19e/0x330
[ 46.637696][ T7] brcmf_cfg80211_attach+0x4a0/0x4040
[ 46.638275][ T7] brcmf_attach+0x389/0xd40
[ 46.638739][ T7] brcmf_usb_probe+0x12de/0x1690
[ 46.639279][ T7] usb_probe_interface+0x2aa/0x760
[ 46.639820][ T7] really_probe+0x205/0xb70
[ 46.640342][ T7] __driver_probe_device+0x311/0x4b0
[ 46.640876][ T7] driver_probe_device+0x4e/0x150
[ 46.641445][ T7] __device_attach_driver+0x1cc/0x2a0
[ 46.642000][ T7] bus_for_each_drv+0x156/0x1d0
[ 46.642543][ T7] __device_attach+0x23f/0x3a0
[ 46.643065][ T7] bus_probe_device+0x1da/0x290
[ 46.643644][ T7] device_add+0xb7b/0x1eb0
[ 46.644130][ T7] usb_set_configuration+0xf59/0x16f0
[ 46.644720][ T7] usb_generic_driver_probe+0x82/0xa0
[ 46.645295][ T7] usb_probe_device+0xbb/0x250
[ 46.645786][ T7] really_probe+0x205/0xb70
[ 46.646258][ T7] __driver_probe_device+0x311/0x4b0
[ 46.646804][ T7] driver_probe_device+0x4e/0x150
[ 46.647387][ T7] __device_attach_driver+0x1cc/0x2a0
[ 46.647926][ T7] bus_for_each_drv+0x156/0x1d0
[ 46.648454][ T7] __device_attach+0x23f/0x3a0
[ 46.648939][ T7] bus_probe_device+0x1da/0x290
[ 46.649478][ T7] device_add+0xb7b/0x1eb0
[ 46.649936][ T7] usb_new_device.cold+0x49c/0x1029
[ 46.650526][ T7] hub_event+0x1c98/0x3950
[ 46.650975][ T7] process_one_work+0x92b/0x1460
[ 46.651535][ T7] worker_thread+0x95/0xe00
[ 46.651991][ T7] kthread+0x3a1/0x480
[ 46.652413][ T7] ret_from_fork+0x1f/0x30
[ 46.652885][ T7]
[ 46.653131][ T7] The buggy address belongs to the object at ffff888019442000
[ 46.653131][ T7] which belongs to the cache kmalloc-2k of size 2048
[ 46.654669][ T7] The buggy address is located 0 bytes inside of
[ 46.654669][ T7] 2048-byte region [ffff888019442000, ffff888019442800)
[ 46.656137][ T7] The buggy address belongs to the page:
[ 46.656720][ T7] page:ffffea0000651000 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x19440
[ 46.657792][ T7] head:ffffea0000651000 order:3 compound_mapcount:0 compound_pincount:0
[ 46.658673][ T7] flags: 0x100000000010200(slab|head|node=0|zone=1)
[ 46.659422][ T7] raw: 01000000000102000000000000000000dead000000000122ffff888100042000
[ 46.660363][ T7] raw: 0000000000000000000000000008000800000001ffffffff0000000000000000
[ 46.661236][ T7] page dumped because: kasan: bad access detected
[ 46.661956][ T7] page_owner tracks the page as allocated
[ 46.662588][ T7] page last allocated via order 3, migratetype Unmovable, gfp_mask 0x52a20(GFP_ATOMIC|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP), pid 7, ts 31136961085, free_ts 0
[ 46.664271][ T7] prep_new_page+0x1aa/0x240
[ 46.664763][ T7] get_page_from_freelist+0x159a/0x27c0
[ 46.665340][ T7] __alloc_pages+0x2da/0x6a0
[ 46.665847][ T7] alloc_pages+0xec/0x1e0
[ 46.666308][ T7] allocate_slab+0x380/0x4e0
[ 46.666770][ T7] ___slab_alloc+0x5bc/0x940
[ 46.667264][ T7] __slab_alloc+0x6d/0x80
[ 46.667712][ T7] kmem_cache_alloc_trace+0x30a/0x330
[ 46.668299][ T7] brcmf_usbdev_qinit.constprop.0+0x50/0x470
[ 46.668885][ T7] brcmf_usb_probe+0xc97/0x1690
[ 46.669438][ T7] usb_probe_interface+0x2aa/0x760
[ 46.669988][ T7] really_probe+0x205/0xb70
[ 46.670487][ T7] __driver_probe_device+0x311/0x4b0
[ 46.671031][ T7] driver_probe_device+0x4e/0x150
[ 46.671604][ T7] __device_attach_driver+0x1cc/0x2a0
[ 46.672192][ T7] bus_for_each_drv+0x156/0x1d0
[ 46.672739][ T7] page_owner free stack trace missing
[ 46.673335][ T7]
[ 46.673620][ T7] Memory state around the buggy address:
[ 46.674213][ T7] ffff888019442700: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 46.675083][ T7] ffff888019442780: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 46.675994][ T7] >ffff888019442800: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 46.676875][ T7] ^
[ 46.677323][ T7] ffff888019442880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 46.678190][ T7] ffff888019442900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 46.679052][ T7] ==================================================================
[ 46.679945][ T7] Disabling lock debugging due to kernel taint
[ 46.680725][ T7] Kernel panic - not syncing:
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230309104457.22628-1-jisoo.jang@yonsei.ac.kr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The root cause is that the worker can force fallback to TCP the first
mptcp subflow, actually deleting the unaccepted msk socket.
We can explicitly prevent the race delaying the unaccepted msk deletion
at listener shutdown time. In case the closed subflow is later accepted,
just drop the mptcp context and let the user-space deal with the
paired mptcp socket.
Fixes: b6985b9b8295 ("mptcp: use the workqueue to destroy unaccepted sockets") Cc: stable@vger.kernel.org Reported-by: Christoph Paasch <cpaasch@apple.com> Link: https://github.com/multipath-tcp/mptcp_net-next/issues/375 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Tested-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a partial revert of the blamed commit, with a relevant
change: mptcp_subflow_queue_clean() now just change the msk
socket status and stop the worker, so that the UaF issue addressed
by the blamed commit is not re-introduced.
The above prevents the mptcp worker from running concurrently with
inet_csk_listen_stop(), as such race would trigger a warning, as
reported by Christoph:
set_mempolicy_home_node() iterates over a list of VMAs and calls
mbind_range() on each VMA, which also iterates over the singular list of
the VMA passed in and potentially splits the VMA. Since the VMA iterator
is not passed through, set_mempolicy_home_node() may now point to a stale
node in the VMA tree. This can result in a UAF as reported by syzbot.
Avoid the stale maple tree node by passing the VMA iterator through to the
underlying call to split_vma().
mbind_range() is also overly complicated, since there are two calling
functions and one already handles iterating over the VMAs. Simplify
mbind_range() to only handle merging and splitting of the VMAs.
Align the new loop in do_mbind() and existing loop in
set_mempolicy_home_node() to use the reduced mbind_range() function. This
allows for a single location of the range calculation and avoids
constantly looking up the previous VMA (since this is a loop over the
VMAs).
Link: https://lore.kernel.org/linux-mm/000000000000c93feb05f87e24ad@google.com/ Fixes: 66850be55e8e ("mm/mempolicy: use vma iterator & maple state instead of vma linked list") Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Reported-by: syzbot+a7c1ec5b1d71ceaa5186@syzkaller.appspotmail.com Link: https://lkml.kernel.org/r/20230410152205.2294819-1-Liam.Howlett@oracle.com Tested-by: syzbot+a7c1ec5b1d71ceaa5186@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read mmu_invalidate_seq before dropping the mmap_lock so that KVM can
detect if the results of vma_lookup() (e.g. vma_shift) become stale
before it acquires kvm->mmu_lock. This fixes a theoretical bug where a
VMA could be changed by userspace after vma_lookup() and before KVM
reads the mmu_invalidate_seq, causing KVM to install page table entries
based on a (possibly) no-longer-valid vma_shift.
Re-order the MMU cache top-up to earlier in user_mem_abort() so that it
is not done after KVM has read mmu_invalidate_seq (i.e. so as to avoid
inducing spurious fault retries).
This bug has existed since KVM/ARM's inception. It's unlikely that any
sane userspace currently modifies VMAs in such a way as to trigger this
race. And even with directed testing I was unable to reproduce it. But a
sufficiently motivated host userspace might be able to exploit this
race.
Fixes: 94f8e6418d39 ("KVM: ARM: Handle guest faults in KVM") Cc: stable@vger.kernel.org Reported-by: Sean Christopherson <seanjc@google.com> Signed-off-by: David Matlack <dmatlack@google.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230313235454.2964067-1-dmatlack@google.com Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
[will: Use FSC_PERM instead of ESR_ELx_FSC_PERM] Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of the Rust support for UML, we disable SSE (and similar flags)
to match the normal x86 builds. This both makes sense (we ideally want a
similar configuration to x86), and works around a crash bug with SSE
generation under Rust with LLVM.
However, this breaks compiling stdlib.h under gcc < 11, as the x86_64
ABI requires floating-point return values be stored in an SSE register.
gcc 11 fixes this by only doing register allocation when a function is
actually used, and since we never use atof(), it shouldn't be a problem:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=99652
Nevertheless, only disable SSE on clang setups, as that's a simple way
of working around everyone's bugs.
Fixes: 884981867947 ("rust: arch/um: Disable FP/SIMD instruction to match x86") Reported-by: Roberto Sassu <roberto.sassu@huaweicloud.com> Link: https://lore.kernel.org/linux-um/6df2ecef9011d85654a82acd607fdcbc93ad593c.camel@huaweicloud.com/ Tested-by: Roberto Sassu <roberto.sassu@huaweicloud.com> Tested-by: SeongJae Park <sj@kernel.org> Signed-off-by: David Gow <davidgow@google.com> Reviewed-by: Vincenzo Palazzo <vincenzopalazzodev@gmail.com> Tested-by: Arthur Grillo <arthurgrillo@riseup.net> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_request_slave_channel() may return NULL which will lead to
NULL pointer dereference error in 'tmp_chan->private'.
Correct this behaviour by, first, switching from deprecated function
dma_request_slave_channel() to dma_request_chan(). Secondly, enable
sanity check for the resuling value of dma_request_chan().
Also, fix description that follows the enacted changes and that
concerns the use of dma_request_slave_channel().
Fixes: 706e2c881158 ("ASoC: fsl_asrc_dma: Reuse the dma channel if available in Back-End") Co-developed-by: Natalia Petrova <n.petrova@fintech.ru> Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com> Link: https://lore.kernel.org/r/20230417133242.53339-1-n.zhandarovich@fintech.ru Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting circular locking dependency which involves
zonelist_update_seq seqlock [1], for this lock is checked by memory
allocation requests which do not need to be retried.
One deadlock scenario is kmalloc(GFP_ATOMIC) from an interrupt handler.
CPU0
----
__build_all_zonelists() {
write_seqlock(&zonelist_update_seq); // makes zonelist_update_seq.seqcount odd
// e.g. timer interrupt handler runs at this moment
some_timer_func() {
kmalloc(GFP_ATOMIC) {
__alloc_pages_slowpath() {
read_seqbegin(&zonelist_update_seq) {
// spins forever because zonelist_update_seq.seqcount is odd
}
}
}
}
// e.g. timer interrupt handler finishes
write_sequnlock(&zonelist_update_seq); // makes zonelist_update_seq.seqcount even
}
This deadlock scenario can be easily eliminated by not calling
read_seqbegin(&zonelist_update_seq) from !__GFP_DIRECT_RECLAIM allocation
requests, for retry is applicable to only __GFP_DIRECT_RECLAIM allocation
requests. But Michal Hocko does not know whether we should go with this
approach.
Another deadlock scenario which syzbot is reporting is a race between
kmalloc(GFP_ATOMIC) from tty_insert_flip_string_and_push_buffer() with
port->lock held and printk() from __build_all_zonelists() with
zonelist_update_seq held.
preventing interrupt context from calling kmalloc(GFP_ATOMIC)
and
preventing printk() from calling console_flush_all()
while zonelist_update_seq.seqcount is odd.
Since Petr Mladek thinks that __build_all_zonelists() can become a
candidate for deferring printk() [2], let's address this problem by
disabling local interrupts in order to avoid kmalloc(GFP_ATOMIC)
and
disabling synchronous printk() in order to avoid console_flush_all()
.
As a side effect of minimizing duration of zonelist_update_seq.seqcount
being odd by disabling synchronous printk(), latency at
read_seqbegin(&zonelist_update_seq) for both !__GFP_DIRECT_RECLAIM and
__GFP_DIRECT_RECLAIM allocation requests will be reduced. Although, from
lockdep perspective, not calling read_seqbegin(&zonelist_update_seq) (i.e.
do not record unnecessary locking dependency) from interrupt context is
still preferable, even if we don't allow calling kmalloc(GFP_ATOMIC)
inside
write_seqlock(&zonelist_update_seq)/write_sequnlock(&zonelist_update_seq)
section...
Link: https://lkml.kernel.org/r/8796b95c-3da3-5885-fddd-6ef55f30e4d3@I-love.SAKURA.ne.jp Fixes: 3d36424b3b58 ("mm/page_alloc: fix race condition between build_all_zonelists and page allocation") Link: https://lkml.kernel.org/r/ZCrs+1cDqPWTDFNM@alley Reported-by: syzbot <syzbot+223c7461c58c58a4cb10@syzkaller.appspotmail.com> Link: https://syzkaller.appspot.com/bug?extid=223c7461c58c58a4cb10 Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Cc: Petr Mladek <pmladek@suse.com> Cc: David Hildenbrand <david@redhat.com> Cc: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Cc: John Ogness <john.ogness@linutronix.de> Cc: Patrick Daly <quic_pdaly@quicinc.com> Cc: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code path can lead to warnings because of uninitialized device,
which contains, as a consequence, uninitialized kobject. The uninitialized
device is passed to of_platform_populate, which will at some point, while
creating child device, try to get a reference on uninitialized parent,
resulting in the following warning:
kobject: '(null)' ((ptrval)): is not initialized, yet kobject_get() is
being called.
The warning is observed after migrating a kernel 5.10.x to 6.1.x.
Reverting commit 0d70af3c2530 ("fpga: bridge: Use standard dev_release for
class driver") seems to remove the warning.
This commit aggregates device_initialize() and device_add() into
device_register() but this new call is done AFTER of_platform_populate
Fixes: 0d70af3c2530 ("fpga: bridge: Use standard dev_release for class driver") Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Acked-by: Xu Yilun <yilun.xu@intel.com> Link: https://lore.kernel.org/r/20230404133102.2837535-2-alexis.lothore@bootlin.com Signed-off-by: Xu Yilun <yilun.xu@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warning raised because pegasus_driver submits transfer request for
bogus URB (pipe type does not match endpoint type). Add sanity check at
probe time for pipe value extracted from endpoint descriptor. Probe
will fail if sanity check fails.
We started disabling '-Warray-bounds' for gcc-12 originally on s390,
because it resulted in some warnings that weren't realistically fixable
(commit 8b202ee21839: "s390: disable -Warray-bounds").
That s390-specific issue was then found to be less common elsewhere, but
generic (see f0be87c42cbd: "gcc-12: disable '-Warray-bounds' universally
for now"), and then later expanded the version check was expanded to
gcc-11 (5a41237ad1d4: "gcc: disable -Warray-bounds for gcc-11 too").
And it turns out that I was much too optimistic in thinking that it's
all going to go away, and here we are with gcc-13 showing all the same
issues. So instead of expanding this one version at a time, let's just
disable it for gcc-11+, and put an end limit to it only when we actually
find a solution.
Yes, I'm sure some of this is because the kernel just does odd things
(like our "container_of()" use, but also knowingly playing games with
things like linker tables and array layouts).
And yes, some of the warnings are likely signs of real bugs, but when
there are hundreds of false positives, that doesn't really help.
After commit d38afeec26ed ("tcp/udp: Call inet6_destroy_sock()
in IPv6 sk->sk_destruct()."), we call inet6_destroy_sock() in
sk->sk_destruct() by setting inet6_sock_destruct() to it to make
sure we do not leak inet6-specific resources.
SCTP sets its own sk->sk_destruct() in the sctp_init_sock(), and
SCTPv6 socket reuses it as the init function.
To call inet6_sock_destruct() from SCTPv6 sk->sk_destruct(), we
set sctp_v6_destruct_sock() in a new init function.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit d38afeec26ed ("tcp/udp: Call inet6_destroy_sock()
in IPv6 sk->sk_destruct()."), we call inet6_destroy_sock() in
sk->sk_destruct() by setting inet6_sock_destruct() to it to make
sure we do not leak inet6-specific resources.
DCCP sets its own sk->sk_destruct() in the dccp_init_sock(), and
DCCPv6 socket shares it by calling the same init function via
dccp_v6_init_sock().
To call inet6_sock_destruct() from DCCPv6 sk->sk_destruct(), we
export it and set dccp_v6_sk_destruct() in the init function.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit d38afeec26ed ("tcp/udp: Call inet6_destroy_sock()
in IPv6 sk->sk_destruct()."), we call inet6_destroy_sock() in
sk->sk_destruct() by setting inet6_sock_destruct() to it to make
sure we do not leak inet6-specific resources.
Now we can remove unnecessary inet6_destroy_sock() calls in
sk->sk_prot->destroy().
DCCP and SCTP have their own sk->sk_destruct() function, so we
change them separately in the following patches.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 32ef9e5054ec, -Wa,-gdwarf-2 is no longer used in KBUILD_AFLAGS.
Instead, it includes -g, the appropriate -gdwarf-* flag, and also the
-Wa versions of both of those if building with Clang and GNU as. As a
result, debug info was being generated for the purgatory objects, even
though the intention was that it not be.
Fixes: 32ef9e5054ec ("Makefile.debug: re-enable debug info for .S files") Signed-off-by: Alyssa Ross <hi@alyssa.is> Cc: stable@vger.kernel.org Acked-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous commit df8629af2934 ("fuse: always revalidate if exclusive
create") ensures that the dentries are revalidated on O_EXCL creates. This
commit complements it by also performing revalidation for rename target
dentries. Otherwise, a rename target file that only exists in kernel
dentry cache but not in the filesystem will result in EEXIST if
RENAME_NOREPLACE flag is used.
Signed-off-by: Jiachen Zhang <zhangjiachen.jaycee@bytedance.com> Signed-off-by: Zhang Tianci <zhangtianci.1997@bytedance.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Yang Bo <yb203166@antfin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per-vcpu flags are updated using a non-atomic RMW operation.
Which means it is possible to get preempted between the read and
write operations.
Another interesting thing to note is that preemption also updates
flags, as we have some flag manipulation in both the load and put
operations.
It is thus possible to lose information communicated by either
load or put, as the preempted flag update will overwrite the flags
when the thread is resumed. This is specially critical if either
load or put has stored information which depends on the physical
CPU the vcpu runs on.
This results in really elusive bugs, and kudos must be given to
Mostafa for the long hours of debugging, and finally spotting
the problem.
Fix it by disabling preemption during the RMW operation, which
ensures that the state stays consistent. Also upgrade vcpu_get_flag
path to use READ_ONCE() to make sure the field is always atomically
accessed.
Fixes: e87abb73e594 ("KVM: arm64: Add helpers to manipulate vcpu flags among a set") Reported-by: Mostafa Saleh <smostafa@google.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230418125737.2327972-1-maz@kernel.org Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do consider thermal pressure in util_fits_cpu() for uclamp_min only.
With the exception of the biggest cores which by definition are the max
performance point of the system and all tasks by definition should fit.
Even under thermal pressure, the capacity of the biggest CPU is the
highest in the system and should still fit every task. Except when it
reaches capacity inversion point, then this is no longer true.
We can handle this by using the inverted capacity as capacity_orig in
util_fits_cpu(). Which not only addresses the problem above, but also
ensure uclamp_max now considers the inverted capacity. Force fitting
a task when a CPU is in this adverse state will contribute to making the
thermal throttling last longer.
Check each performance domain to see if thermal pressure is causing its
capacity to be lower than another performance domain.
We assume that each performance domain has CPUs with the same
capacities, which is similar to an assumption made in energy_model.c
We also assume that thermal pressure impacts all CPUs in a performance
domain equally.
If there're multiple performance domains with the same capacity_orig, we
will trigger a capacity inversion if the domain is under thermal
pressure.
The new cpu_in_capacity_inversion() should help users to know when
information about capacity_orig are not reliable and can opt in to use
the inverted capacity as the 'actual' capacity_orig.
The maple tree limits the gap returned to a window that specifically fits
what was asked. This may not be optimal in the case of switching search
directions or a gap that does not satisfy the requested space for other
reasons. Fix the search by retrying the operation and limiting the search
window in the rare occasion that a conflict occurs.
Link: https://lkml.kernel.org/r/20230414185919.4175572-1-Liam.Howlett@oracle.com Fixes: 3499a13168da ("mm/mmap: use maple tree for unmapped_area{_topdown}") Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Reported-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bug was reported by Yuanxi Liu where allocating 1G pages at runtime is
taking an excessive amount of time for large amounts of memory. Further
testing allocating huge pages that the cost is linear i.e. if allocating
1G pages in batches of 10 then the time to allocate nr_hugepages from
10->20->30->etc increases linearly even though 10 pages are allocated at
each step. Profiles indicated that much of the time is spent checking the
validity within already existing huge pages and then attempting a
migration that fails after isolating the range, draining pages and a whole
lot of other useless work.
Commit eb14d4eefdc4 ("mm,page_alloc: drop unnecessary checks from
pfn_range_valid_contig") removed two checks, one which ignored huge pages
for contiguous allocations as huge pages can sometimes migrate. While
there may be value on migrating a 2M page to satisfy a 1G allocation, it's
potentially expensive if the 1G allocation fails and it's pointless to try
moving a 1G page for a new 1G allocation or scan the tail pages for valid
PFNs.
Reintroduce the PageHuge check and assume any contiguous region with
hugetlbfs pages is unsuitable for a new 1G allocation.
The hpagealloc test allocates huge pages in batches and reports the
average latency per page over time. This test happens just after boot
when fragmentation is not an issue. Units are in milliseconds.
The vanilla kernel is poor, taking up to 1.3 second to allocate a huge
page and almost 10 minutes in total to run the test. Reverting the
problematic commit reduces it to 8ms at worst and the patch takes 26ms.
This patch fixes the main issue with skipping huge pages but leaves the
page_count() out because a page with an elevated count potentially can
migrate.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=217022 Link: https://lkml.kernel.org/r/20230414141429.pwgieuwluxwez3rj@techsingularity.net Fixes: eb14d4eefdc4 ("mm,page_alloc: drop unnecessary checks from pfn_range_valid_contig") Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reported-by: Yuanxi Liu <y.liu@naruida.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As reported by Dipanjan Das, when KMSAN is used together with kernel fault
injection (or, generally, even without the latter), calls to kcalloc() or
__vmap_pages_range_noflush() may fail, leaving the metadata mappings for
the virtual mapping in an inconsistent state. When these metadata
mappings are accessed later, the kernel crashes.
To address the problem, we return a non-zero error code from
kmsan_vmap_pages_range_noflush() in the case of any allocation/mapping
failure inside it, and make vmap_pages_range_noflush() return an error if
KMSAN fails to allocate the metadata.
This patch also removes KMSAN_WARN_ON() from vmap_pages_range_noflush(),
as these allocation failures are not fatal anymore.
Link: https://lkml.kernel.org/r/20230413131223.4135168-1-glider@google.com Fixes: b073d7f8aee4 ("mm: kmsan: maintain KMSAN metadata for page operations") Signed-off-by: Alexander Potapenko <glider@google.com> Reported-by: Dipanjan Das <mail.dipanjan.das@gmail.com> Link: https://lore.kernel.org/linux-mm/CANX2M5ZRrRA64k0hOif02TjmY9kbbO2aCBPyq79es34RXZ=cAw@mail.gmail.com/ Reviewed-by: Marco Elver <elver@google.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similarly to kmsan_vmap_pages_range_noflush(), kmsan_ioremap_page_range()
must also properly handle allocation/mapping failures. In the case of
such, it must clean up the already created metadata mappings and return an
error code, so that the error can be propagated to ioremap_page_range().
Without doing so, KMSAN may silently fail to bring the metadata for the
page range into a consistent state, which will result in user-visible
crashes when trying to access them.
Link: https://lkml.kernel.org/r/20230413131223.4135168-2-glider@google.com Fixes: b073d7f8aee4 ("mm: kmsan: maintain KMSAN metadata for page operations") Signed-off-by: Alexander Potapenko <glider@google.com> Reported-by: Dipanjan Das <mail.dipanjan.das@gmail.com> Link: https://lore.kernel.org/linux-mm/CANX2M5ZRrRA64k0hOif02TjmY9kbbO2aCBPyq79es34RXZ=cAw@mail.gmail.com/ Reviewed-by: Marco Elver <elver@google.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
split_huge_page_to_list() WARNs when called for huge zero pages, which
sounds to me too harsh because it does not imply a kernel bug, but just
notifies the event to admins. On the other hand, this is considered as
critical by syzkaller and makes its testing less efficient, which seems to
me harmful.
So replace the VM_WARN_ON_ONCE_FOLIO with pr_warn_ratelimited.
Link: https://lkml.kernel.org/r/20230406082004.2185420-1-naoya.horiguchi@linux.dev Fixes: 478d134e9506 ("mm/huge_memory: do not overkill when splitting huge_zero_page") Signed-off-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Reported-by: syzbot+07a218429c8d19b1fb25@syzkaller.appspotmail.com Link: https://lore.kernel.org/lkml/000000000000a6f34a05e6efcd01@google.com/ Reviewed-by: Yang Shi <shy828301@gmail.com> Cc: Miaohe Lin <linmiaohe@huawei.com> Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Xu Yu <xuyu@linux.alibaba.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Khugepaged collapse an anonymous thp in two rounds of scans. The 2nd
round done in __collapse_huge_page_isolate() after
hpage_collapse_scan_pmd(), during which all the locks will be released
temporarily. It means the pgtable can change during this phase before 2nd
round starts.
It's logically possible some ptes got wr-protected during this phase, and
we can errornously collapse a thp without noticing some ptes are
wr-protected by userfault. e1e267c7928f wanted to avoid it but it only
did that for the 1st phase, not the 2nd phase.
Since __collapse_huge_page_isolate() happens after a round of small page
swapins, we don't need to worry on any !present ptes - if it existed
khugepaged will already bail out. So we only need to check present ptes
with uffd-wp bit set there.
This is something I found only but never had a reproducer, I thought it
was one caused a bug in Muhammad's recent pagemap new ioctl work, but it
turns out it's not the cause of that but an userspace bug. However this
seems to still be a real bug even with a very small race window, still
worth to have it fixed and copy stable.
Link: https://lkml.kernel.org/r/20230405155120.3608140-1-peterx@redhat.com Fixes: e1e267c7928f ("khugepaged: skip collapse if uffd-wp detected") Signed-off-by: Peter Xu <peterx@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Yang Shi <shy828301@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like what we fixed for hugetlb in commit 44f86392bdd1 ("mm/hugetlb:
fix uffd-wp handling for migration entries in
hugetlb_change_protection()") similarly applies to THP.
Setting/clearing uffd-wp on THP migration entries is not implemented
properly. Further, while removing migration PMDs considers the uffd-wp
bit, inserting migration PMDs does not consider the uffd-wp bit.
We have to set/clear independently of the migration entry type in
change_huge_pmd() and properly copy the uffd-wp bit in
set_pmd_migration_entry().
Verified using a simple reproducer that triggers migration of a THP, that
the set_pmd_migration_entry() no longer loses the uffd-wp bit.
Link: https://lkml.kernel.org/r/20230405160236.587705-2-david@redhat.com Fixes: f45ec5ff16a7 ("userfaultfd: wp: support swap and page migration") Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> Cc: Muhammad Usama Anjum <usama.anjum@collabora.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
afa965a45e01 ("drm/rockchip: vop2: fix suspend/resume") uses
regmap_reinit_cache() to fix the suspend/resume issue with the VOP2
driver. During discussion it came up that we should rather use
regcache_sync() instead. As the original patch is already applied
fix this up in this follow-up patch.
During a suspend/resume cycle the VO power domain will be disabled and
the VOP2 registers will reset to their default values. After that the
cached register values will be out of sync and the read/modify/write
operations we do on the window registers will result in bogus values
written. Fix this by re-initializing the register cache each time we
enable the VOP2. With this the VOP2 will show a picture after a
suspend/resume cycle whereas without this the screen stays dark.
[Why]
After gpu-reset, sometimes the driver fails to enable vblank irq,
causing flip_done timed out and the desktop freezed.
During gpu-reset, we disable and enable vblank irq in dm_suspend() and
dm_resume(). Later on in amdgpu_irq_gpu_reset_resume_helper(), we check
irqs' refcount and decide to enable or disable the irqs again.
However, we have 2 sets of API for controling vblank irq, one is
dm_vblank_get/put() and another is amdgpu_irq_get/put(). Each API has
its own refcount and flag to store the state of vblank irq, and they
are not synchronized.
In drm we use the first API to control vblank irq but in
amdgpu_irq_gpu_reset_resume_helper() we use the second set of API.
The failure happens when vblank irq was enabled by dm_vblank_get()
before gpu-reset, we have vblank->enabled true. However, during
gpu-reset, in amdgpu_irq_gpu_reset_resume_helper() vblank irq's state
checked from amdgpu_irq_update() is DISABLED. So finally it disables
vblank irq again. After gpu-reset, if there is a cursor plane commit,
the driver will try to enable vblank irq by calling drm_vblank_enable(),
but the vblank->enabled is still true, so it fails to turn on vblank
irq and causes flip_done can't be completed in vblank irq handler and
desktop become freezed.
[How]
Combining the 2 vblank control APIs by letting drm's API finally calls
amdgpu_irq's API, so the irq's refcount and state of both APIs can be
synchronized. Also add a check to prevent refcount from being less then
0 in amdgpu_irq_put().
v2:
- Add warning in amdgpu_irq_enable() if the irq is already disabled.
- Call dc_interrupt_set() in dm_set_vblank() to avoid refcount change
if it is in gpu-reset.
v3:
- Improve commit message and code comments.
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fast wake should use 8 SYNC pulses for the preamble
and 10-16 SYNC pulses for the precharge. Reduce our
fast wake SYNC count to match the maximum value.
We also use the maximum precharge length for normal
AUX transactions.
Timing Information in Datasheet assumes that HIGH_SPEED_ENA=1 should be
set for SDR12 and SDR25 modes. But sdhci_am654 driver clears
HIGH_SPEED_ENA register. Thus, Modify sdhci_am654 to not clear
HIGH_SPEED_ENA (HOST_CONTROL[2]) bit for SDR12 and SDR25 speed modes.
bdi_split_work_to_wbs() traverses &bdi->wb_list to split work into all
wbs. If the allocation of new work fails, the on-stack fallback will be
used and the reference count of the current wb is increased afterwards.
If cgroup writeback membership switches occur before getting the reference
count and the current wb is released as old_wd, then calling wb_get() or
wb_put() will trigger the null pointer dereference above.
This issue was introduced in v4.3-rc7 (see fix tag1). Both
sync_inodes_sb() and __writeback_inodes_sb_nr() calls to
bdi_split_work_to_wbs() can trigger this issue. For scenarios called via
sync_inodes_sb(), originally commit 7fc5854f8c6e ("writeback: synchronize
sync(2) against cgroup writeback membership switches") reduced the
possibility of the issue by adding wb_switch_rwsem, but in v5.14-rc1 (see
fix tag2) removed the "inode_io_list_del_locked(inode, old_wb)" from
inode_switch_wbs_work_fn() so that wb->state contains WB_has_dirty_io,
thus old_wb is not skipped when traversing wbs in bdi_split_work_to_wbs(),
and the issue becomes easily reproducible again.
To solve this problem, percpu_ref_exit() is called under RCU protection to
avoid race between cgwb_release_workfn() and bdi_split_work_to_wbs().
Moreover, replace wb_get() with wb_tryget() in bdi_split_work_to_wbs(),
and skip the current wb if wb_tryget() fails because the wb has already
been shutdown.
Link: https://lkml.kernel.org/r/20230410130826.1492525-1-libaokun1@huawei.com Fixes: b817525a4a80 ("writeback: bdi_writeback iteration must not skip dying ones") Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Acked-by: Tejun Heo <tj@kernel.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Andreas Dilger <adilger.kernel@dilger.ca> Cc: Christian Brauner <brauner@kernel.org> Cc: Dennis Zhou <dennis@kernel.org> Cc: Hou Tao <houtao1@huawei.com> Cc: yangerkun <yangerkun@huawei.com> Cc: Zhang Yi <yi.zhang@huawei.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linux Security Modules (LSMs) that implement the "capable" hook will
usually emit an access denial message to the audit log whenever they
"block" the current task from using the given capability based on their
security policy.
The occurrence of a denial is used as an indication that the given task
has attempted an operation that requires the given access permission, so
the callers of functions that perform LSM permission checks must take care
to avoid calling them too early (before it is decided if the permission is
actually needed to perform the requested operation).
The __sys_setres[ug]id() functions violate this convention by first
calling ns_capable_setid() and only then checking if the operation
requires the capability or not. It means that any caller that has the
capability granted by DAC (task's capability set) but not by MAC (LSMs)
will generate a "denied" audit record, even if is doing an operation for
which the capability is not required.
Fix this by reordering the checks such that ns_capable_setid() is checked
last and -EPERM is returned immediately if it returns false.
While there, also do two small optimizations:
* move the capability check before prepare_creds() and
* bail out early in case of a no-op.
Link: https://lkml.kernel.org/r/20230217162154.837549-1-omosnace@redhat.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling dev_set_name() memory is allocated for the name for the
struct device. Once that structure device is registered, or attempted
to be registerd, with the driver core, the driver core will handle
cleaning up that memory when the device is removed from the system.
Unfortunatly for the memstick code, there is an error path that causes
the struct device to never be registered, and so the memory allocated in
dev_set_name will be leaked. Fix that leak by manually freeing it right
before the memory for the device is freed.
Syzbot still reports uninit-value in nilfs_add_checksums_on_logs() for
KMSAN enabled kernels after applying commit 7397031622e0 ("nilfs2:
initialize "struct nilfs_binfo_dat"->bi_pad field").
This is because the unused bytes at the end of each block in segment
summaries are not initialized. So this fixes the issue by padding the
unused bytes with null bytes.
In mas_alloc_nodes(), "node->node_count = 0" means to initialize the
node_count field of the new node, but the node may not be a new node. It
may be a node that existed before and node_count has a value, setting it
to 0 will cause a memory leak. At this time, mas->alloc->total will be
greater than the actual number of nodes in the linked list, which may
cause many other errors. For example, out-of-bounds access in
mas_pop_node(), and mas_pop_node() may return addresses that should not be
used. Fix it by initializing node_count only for new nodes.
Also, by the way, an if-else statement was removed to simplify the code.
Link: https://lkml.kernel.org/r/20230411041005.26205-1-zhangpeng.00@bytedance.com Fixes: 54a611b60590 ("Maple Tree: add new data structure") Signed-off-by: Peng Zhang <zhangpeng.00@bytedance.com> Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The internal function of mas_awalk() was incorrectly skipping the last
entry in a node, which could potentially be NULL. This is only a problem
for the left-most node in the tree - otherwise that NULL would not exist.
Fix mas_awalk() by using the metadata to obtain the end of the node for
the loop and the logical pivot as apposed to the raw pivot value.
Link: https://lkml.kernel.org/r/20230414145728.4067069-2-Liam.Howlett@oracle.com Fixes: 54a611b60590 ("Maple Tree: add new data structure") Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Reported-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop using maple state min/max for the range by passing through pointers
for those values. This will allow the maple state to be reused without
resetting.
Also add some logic to fail out early on searching with invalid
arguments.
Link: https://lkml.kernel.org/r/20230414145728.4067069-1-Liam.Howlett@oracle.com Fixes: 54a611b60590 ("Maple Tree: add new data structure") Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Reported-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vm_map_base, empty_zero_page and invalid_pmd_table could be accessed
widely by some out-of-tree non-GPL but important file systems or drivers
(e.g. OpenZFS). Let's use EXPORT_SYMBOL() instead of EXPORT_SYMBOL_GPL()
to export them, so as to avoid build errors.
1, Details about vm_map_base:
This is a LoongArch-specific symbol and may be referenced through macros
PCI_IOBASE, VMALLOC_START and VMALLOC_END.
2, Details about empty_zero_page:
As it stands today, only 3 architectures export empty_zero_page as a GPL
symbol: IA64, LoongArch and MIPS. LoongArch gets the GPL export by
inheriting from MIPS, and the MIPS export was first introduced in commit 497d2adcbf50b ("[MIPS] Export empty_zero_page for sake of the ext4
module."). The IA64 export was similar: commit a7d57ecf4216e ("[IA64]
Export three symbols for module use") did so for kvm.
In both IA64 and MIPS, the export of empty_zero_page was done for
satisfying some in-kernel component built as module (kvm and ext4
respectively), and given its reasonably low-level nature, GPL is a
reasonable choice. But looking at the bigger picture it is evident most
other architectures do not regard it as GPL, so in effect the symbol
probably should not be treated as such, in favor of consistency.
3, Details about invalid_pmd_table:
Keep consistency with invalid_pte_table and make it be possible by some
modules.
Not all LoongArch processors support CRC32 instructions. This feature
is indicated by CPUCFG1.CRC32 (Bit25) but it is wrongly defined in the
previous versions of the ISA manual (and so does in loongarch.h). The
CRC32 feature is set unconditionally now, so fix it.
At find_delalloc_subrange(), when we need to get the next extent map, we
do a full search on the extent map tree (a red black tree). This is fine
but it's a lot more efficient to simply use rb_next(), which typically
requires iterating over less nodes of the tree and never needs to compare
the ranges of nodes with the one we are looking for.
So add a public helper to extent_map.{h,c} to get the extent map that
immediately follows another extent map, using rb_next(), and use that
helper at find_delalloc_subrange().
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tsl2772_read_prox_diodes() will correctly parse the properties from
device tree to determine which proximity diode(s) to read from, however
it didn't actually set this value on the struct tsl2772_settings. Let's
go ahead and fix that.
In ad5755_parse_fw(), we should add fwnode_handle_put()
when break out of the iteration device_for_each_child_node()
as it will automatically increase and decrease the refcounter.
Fixes: 3ac27afefd5d ("iio:dac:ad5755: Switch to generic firmware properties and drop pdata") Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20230322035627.1856421-1-windhl@126.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VCN firmware loading path enables the indirect SRAM mode if it's
advertised as supported. We might have some cases of FW issues that
prevents this mode to working properly though, ending-up in a failed
probe. An example below, observed in the Steam Deck:
[...]
[drm] failed to load ucode VCN0_RAM(0x3A)
[drm] psp gfx command LOAD_IP_FW(0x6) failed and response status is (0xFFFF0000)
amdgpu 0000:04:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring vcn_dec_0 test failed (-110)
[drm:amdgpu_device_init.cold [amdgpu]] *ERROR* hw_init of IP block <vcn_v3_0> failed -110
amdgpu 0000:04:00.0: amdgpu: amdgpu_device_ip_init failed
amdgpu 0000:04:00.0: amdgpu: Fatal error during GPU init
[...]
Disabling the VCN block circumvents this, but it's a very invasive
workaround that turns off the entire feature. So, let's add a quirk
on VCN loading that checks for known problematic BIOSes on Vangogh,
so we can proactively disable the indirect SRAM mode and allow the
HW proper probe and VCN IP block to work fine.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2385 Fixes: 82132ecc5432 ("drm/amdgpu: enable Vangogh VCN indirect sram mode") Cc: stable@vger.kernel.org Cc: James Zhu <James.Zhu@amd.com> Cc: Leo Liu <leo.liu@amd.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I found this when writing a simple UFFDIO_API test to be the first unit
test in this set. Two things breaks with the commit:
- UFFDIO_API check was lost and missing. According to man page, the
kernel should reject ioctl(UFFDIO_API) if uffdio_api.api != 0xaa. This
check is needed if the api version will be extended in the future, or
user app won't be able to identify which is a new kernel.
- Feature flags checks were removed, which means UFFDIO_API with a
feature that does not exist will also succeed. According to the man
page, we should (and it makes sense) to reject ioctl(UFFDIO_API) if
unknown features passed in.
Link: https://lore.kernel.org/r/20220722201513.1624158-1-axelrasmussen@google.com Link: https://lkml.kernel.org/r/20230412163922.327282-2-peterx@redhat.com Fixes: 914eedcb9ba0 ("userfaultfd: don't fail on unrecognized features") Signed-off-by: Peter Xu <peterx@redhat.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Dmitry Safonov <0x7f454c46@gmail.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Zach O'Keefe <zokeefe@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To solve this, remove the
lookup and create the directory on the first device found, and then
remove it when the module is unloaded.
When we allocate a nvme-tcp queue, we set the data_ready callback before
we actually need to use it. This creates the potential that if a stray
controller sends us data on the socket before we connect, we can trigger
the io_work and start consuming the socket.
In this case reported: we failed to allocate one of the io queues, and
as we start releasing the queues that we already allocated, we get
a UAF [1] from the io_work which is running before it should really.
Fix this by setting the socket ops callbacks only before we start the
queue, so that we can't accidentally schedule the io_work in the
initialization phase before the queue started. While we are at it,
rename nvme_tcp_restore_sock_calls to pair with nvme_tcp_setup_sock_ops.
The drm_buddy_test KUnit tests verify that returned blocks have sizes
which are powers of two using is_power_of_2(). However, is_power_of_2()
operations on a 'long', but the block size is a u64. So on systems where
long is 32-bit, this can sometimes fail even on correctly sized blocks.
This only reproduces randomly, as the parameters passed to the buddy
allocator in this test are random. The seed 0xb2e06022 reproduced it
fine here.
For now, just hardcode an is_power_of_2() implementation using
x & (x - 1).
Signed-off-by: David Gow <davidgow@google.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Maíra Canal <mcanal@igalia.com> Reviewed-by: Arunpravin Paneer Selvam <arunpravin.paneerselvam@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230329065532.2122295-2-davidgow@google.com Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The drm buddy allocator tests were broken on 32-bit systems, as
rounddown_pow_of_two() takes a long, and the buddy allocator handles
64-bit sizes even on 32-bit systems.
This can be reproduced with the drm_buddy_allocator KUnit tests on i386:
./tools/testing/kunit/kunit.py run --arch i386 \
--kunitconfig ./drivers/gpu/drm/tests drm_buddy
(It results in kernel BUG_ON() when too many blocks are created, due to
the block size being too small.)
This was independently uncovered (and fixed) by Luís Mendes, whose patch
added a new u64 variant of rounddown_pow_of_two(). This version instead
recalculates the size based on the order.
Implement phy_read16() and phy_write16() ops for B53 MMAP to avoid accessing
B53_PORT_MII_PAGE registers which hangs the device.
This access should be done through the MDIO Mux bus controller.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some USB-SATA adapters have broken behavior when an unsupported VPD page is
probed: Depending on the VPD page number, a 4-byte header with a valid VPD
page number but with a 0 length is returned. Currently, scsi_vpd_inquiry()
only checks that the page number is valid to determine if the page is
valid, which results in receiving only the 4-byte header for the
non-existent page. This error manifests itself very often with page 0xb9
for the Concurrent Positioning Ranges detection done by sd_read_cpr(),
resulting in the following error message:
Building sigaltstack with clang via:
$ ARCH=x86 make LLVM=1 -C tools/testing/selftests/sigaltstack/
produces the following warning:
warning: variable 'sp' is uninitialized when used here [-Wuninitialized]
if (sp < (unsigned long)sstack ||
^~
Clang expects these to be declared at global scope; we've fixed this in
the kernel proper by using the macro `current_stack_pointer`. This is
defined in different headers for different target architectures, so just
create a new header that defines the arch-specific register names for
the stack pointer register, and define it for more targets (at least the
ones that support current_stack_pointer/ARCH_HAS_CURRENT_STACK_POINTER).
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org> Link: https://lore.kernel.org/lkml/CA+G9fYsi3OOu7yCsMutpzKDnBMAzJBCPimBp86LhGBa0eCnEpA@mail.gmail.com/ Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Tested-by: Linux Kernel Functional Testing <lkft@linaro.org> Tested-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for A320M-S2H V2. Tested using module force_load option.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au> Acked-by: Thomas Weißschuh <linux@weissschuh.net> Link: https://lore.kernel.org/r/20230318091441.1240921-1-frank@crawford.emu.id.au Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The first error handling code in intel_vsec_add_aux misses the
deallocation of intel_vsec_dev->resource.
Fix this by adding kfree(intel_vsec_dev->resource) in the error handling
code.
Reviewed-by: David E. Box <david.e.box@linux.intel.com> Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/r/20230309040107.534716-4-dzm91@hust.edu.cn Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the nid_t field so that its size is correctly reported in the text
format embedded in trace.dat files. As it stands, it is reported as
being of size 4:
field:nid_t nid[3]; offset:24; size:4; signed:0;
Instead of 12:
field:nid_t nid[3]; offset:24; size:12; signed:0;
This also fixes the reported offset of subsequent fields so that they
match with the actual struct layout.
Signed-off-by: Douglas Raillard <douglas.raillard@arm.com> Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com> Reviewed-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a structural problem in switchdev, where the flag bits in
struct switchdev_notifier_fdb_info (added_by_user, is_local etc) only
represent a simplified / denatured view of what's in struct
net_bridge_fdb_entry :: flags (BR_FDB_ADDED_BY_USER, BR_FDB_LOCAL etc).
Each time we want to pass more information about struct
net_bridge_fdb_entry :: flags to struct switchdev_notifier_fdb_info
(here, BR_FDB_STATIC), we find that FDB entries were already notified to
switchdev with no regard to this flag, and thus, switchdev drivers had
no indication whether the notified entries were static or not.
For example, this command:
ip link add br0 type bridge && ip link set swp0 master br0
bridge fdb add dev swp0 00:01:02:03:04:05 master dynamic
has never worked as intended with switchdev. It causes a struct
net_bridge_fdb_entry to be passed to br_switchdev_fdb_notify() which has
a single flag set: BR_FDB_ADDED_BY_USER.
This is further passed to the switchdev notifier chain, where interested
drivers have no choice but to assume this is a static (does not age) and
sticky (does not migrate) FDB entry. So currently, all drivers offload
it to hardware as such, as can be seen below ("offload" is set).
bridge fdb get 00:01:02:03:04:05 dev swp0 master
00:01:02:03:04:05 dev swp0 offload master br0
The software FDB entry expires $ageing_time centiseconds after the
kernel last sees a packet with this MAC SA, and the bridge notifies its
deletion as well, so it eventually disappears from hardware too.
This is a problem, because it is actually desirable to start offloading
"master dynamic" FDB entries correctly - they should expire $ageing_time
centiseconds after the *hardware* port last sees a packet with this
MAC SA - and this is how the current incorrect behavior was discovered.
With an offloaded data plane, it can be expected that software only sees
exception path packets, so an otherwise active dynamic FDB entry would
be aged out by software sooner than it should.
With the change in place, these FDB entries are no longer offloaded:
bridge fdb get 00:01:02:03:04:05 dev swp0 master
00:01:02:03:04:05 dev swp0 master br0
and this also constitutes a better way (assuming a backport to stable
kernels) for user space to determine whether the kernel has the
capability of doing something sane with these or not.
As opposed to "master dynamic" FDB entries, on the current behavior of
which no one currently depends on (which can be deduced from the lack of
kselftests), Ido Schimmel explains that entries with the "extern_learn"
flag (BR_FDB_ADDED_BY_EXT_LEARN) should still be notified to switchdev,
since the spectrum driver listens to them (and this is kind of okay,
because although they are treated identically to "static", they are
expected to not age, and to roam).
While using i219-LM card currently it was only possible to achieve
about 60% of maximum speed due to regression introduced in Linux 5.8.
This was caused by TSO not being disabled by default despite commit f29801030ac6 ("e1000e: Disable TSO for buffer overrun workaround").
Fix that by disabling TSO during driver probe.
Fixes: f29801030ac6 ("e1000e: Disable TSO for buffer overrun workaround") Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230417205345.1030801-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
from 6 to 9: safe
verification time 110 usec
stack depth 4
processed 36 insns (limit 1000000) max_states_per_insn 0 total_states 3 peak_states 3 mark_read 2
The verifier considers this program as safe by mistakenly pruning unsafe
code paths. In the above func#0, code lines 0-10 are of interest. In line
0-3 registers r6 to r9 are initialized with known scalar values. In line 4
the register r6 is reset to an unknown scalar given the verifier does not
track modulo operations. Due to this, the verifier can also not determine
precisely which branches in line 6 and 9 are taken, therefore it needs to
explore them both.
As can be seen, the verifier starts with exploring the false/fall-through
paths first. The 'from 19 to 21' path has both r6=0 and r9=0 and the pointer
arithmetic on r0 += r6 is therefore considered safe. Given the arithmetic,
r6 is correctly marked for precision tracking where backtracking kicks in
where it walks back the current path all the way where r6 was set to 0 in
the fall-through branch.
Next, the pruning logics pops the path 'from 9 to 11' from the stack. Also
here, the state of the registers is the same, that is, r6=0 and r9=0, so
that at line 19 the path can be pruned as it is considered safe. It is
interesting to note that the conditional in line 9 turned r6 into a more
precise state, that is, in the fall-through path at the beginning of line
10, it is R6=scalar(umin=1), and in the branch-taken path (which is analyzed
here) at the beginning of line 11, r6 turned into a known const r6=0 as
r9=0 prior to that and therefore (unsigned) r6 <= 0 concludes that r6 must
be 0 (**):
from 9 to 11: R1=ctx(off=0,imm=0) R6=0 R7=0 R8=0 R9=0 R10=fp0
[...]
The next path is 'from 6 to 9'. The verifier considers the old and current
state equivalent, and therefore prunes the search incorrectly. Looking into
the two states which are being compared by the pruning logic at line 9, the
old state consists of R6_rwD=Pscalar() R9_rwD=0 R10=fp0 and the new state
consists of R1=ctx(off=0,imm=0) R6_w=scalar(umax=18446744071562067968)
R7_w=0 R8_w=0 R9_w=-2147483648 R10=fp0. While r6 had the reg->precise flag
correctly set in the old state, r9 did not. Both r6'es are considered as
equivalent given the old one is a superset of the current, more precise one,
however, r9's actual values (0 vs 0x80000000) mismatch. Given the old r9
did not have reg->precise flag set, the verifier does not consider the
register as contributing to the precision state of r6, and therefore it
considered both r9 states as equivalent. However, for this specific pruned
path (which is also the actual path taken at runtime), register r6 will be
0x400 and r9 0x80000000 when reaching line 21, thus oob-accessing the map.
The purpose of precision tracking is to initially mark registers (including
spilled ones) as imprecise to help verifier's pruning logic finding equivalent
states it can then prune if they don't contribute to the program's safety
aspects. For example, if registers are used for pointer arithmetic or to pass
constant length to a helper, then the verifier sets reg->precise flag and
backtracks the BPF program instruction sequence and chain of verifier states
to ensure that the given register or stack slot including their dependencies
are marked as precisely tracked scalar. This also includes any other registers
and slots that contribute to a tracked state of given registers/stack slot.
This backtracking relies on recorded jmp_history and is able to traverse
entire chain of parent states. This process ends only when all the necessary
registers/slots and their transitive dependencies are marked as precise.
The backtrack_insn() is called from the current instruction up to the first
instruction, and its purpose is to compute a bitmask of registers and stack
slots that need precision tracking in the parent's verifier state. For example,
if a current instruction is r6 = r7, then r6 needs precision after this
instruction and r7 needs precision before this instruction, that is, in the
parent state. Hence for the latter r7 is marked and r6 unmarked.
For the class of jmp/jmp32 instructions, backtrack_insn() today only looks
at call and exit instructions and for all other conditionals the masks
remain as-is. However, in the given situation register r6 has a dependency
on r9 (as described above in **), so also that one needs to be marked for
precision tracking. In other words, if an imprecise register influences a
precise one, then the imprecise register should also be marked precise.
Meaning, in the parent state both dest and src register need to be tracked
for precision and therefore the marking must be more conservative by setting
reg->precise flag for both. The precision propagation needs to cover both
for the conditional: if the src reg was marked but not the dst reg and vice
versa.
During initialization the driver issues a reset command via its command
interface in order to remove previous configuration from the device.
After issuing the reset, the driver waits for 200ms before polling on
the "system_status" register using memory-mapped IO until the device
reaches a ready state (0x5E). The wait is necessary because the reset
command only triggers the reset, but the reset itself happens
asynchronously. If the driver starts polling too soon, the read of the
"system_status" register will never return and the system will crash
[1].
The issue was discovered when the device was flashed with a development
firmware version where the reset routine took longer to complete. The
issue was fixed in the firmware, but it exposed the fact that the
current wait time is borderline.
Fix by increasing the wait time from 200ms to 400ms. With this patch and
the buggy firmware version, the issue did not reproduce in 10 reboots
whereas without the patch the issue is reproduced quite consistently.
[1]
mce: CPUs not responding to MCE broadcast (may include false positives): 0,4
mce: CPUs not responding to MCE broadcast (may include false positives): 0,4
Kernel panic - not syncing: Timeout: Not all CPUs entered broadcast exception handler
Shutting down cpus with NMI
Kernel Offset: 0x12000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
Fixes: ac004e84164e ("mlxsw: pci: Wait longer before accessing the device after reset") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes a missing 8 byte for the header size calculation. The
ipv6_rpl_srh_size() is used to check a skb_pull() on skb->data which
points to skb_transport_header(). Currently we only check on the
calculated addresses fields using CmprI and CmprE fields, see:
https://www.rfc-editor.org/rfc/rfc6554#section-3
there is however a missing 8 byte inside the calculation which stands
for the fields before the addresses field. Those 8 bytes are represented
by sizeof(struct ipv6_rpl_sr_hdr) expression.
Fixes: 8610c7c6e3bd ("net: ipv6: add support for rpl sr exthdr") Signed-off-by: Alexander Aring <aahringo@redhat.com> Reported-by: maxpl0it <maxpl0it@protonmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a net device is put administratively up, its 'IFF_UP' flag is set
(if not set already) and a 'NETDEV_UP' notification is emitted, which
causes the 8021q driver to add VLAN ID 0 on the device. The reverse
happens when a net device is put administratively down.
When changing the type of a bond to Ethernet, its 'IFF_UP' flag is
incorrectly cleared, resulting in the kernel skipping the above process
and VLAN ID 0 being leaked [1].
Fix by restoring the flag when changing the type to Ethernet, in a
similar fashion to the restoration of the 'IFF_SLAVE' flag.
The issue can be reproduced using the script in [2], with example out
before and after the fix in [3].
[2]
ip link add name t-nlmon type nlmon
ip link add name t-dummy type dummy
ip link add name t-bond type bond mode active-backup
ip link set dev t-bond up
ip link set dev t-nlmon master t-bond
ip link set dev t-nlmon nomaster
ip link show dev t-bond
ip link set dev t-dummy master t-bond
ip link show dev t-bond
ip link del dev t-bond
ip link del dev t-dummy
ip link del dev t-nlmon
[3]
Before:
12: t-bond: <NO-CARRIER,BROADCAST,MULTICAST,MASTER,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default qlen 1000
link/netlink
12: t-bond: <BROADCAST,MULTICAST,MASTER,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether 46:57:39:a4:46:a2 brd ff:ff:ff:ff:ff:ff
After:
12: t-bond: <NO-CARRIER,BROADCAST,MULTICAST,MASTER,UP> mtu 1500 qdisc noqueue state DOWN mode DEFAULT group default qlen 1000
link/netlink
12: t-bond: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether 66:48:7b:74:b6:8a brd ff:ff:ff:ff:ff:ff
Fixes: e36b9d16c6a6 ("bonding: clean muticast addresses when device changes type") Fixes: 75c78500ddad ("bonding: remap muticast addresses without using dev_close() and dev_open()") Fixes: 9ec7eb60dcbc ("bonding: restore IFF_MASTER/SLAVE flags on bond enslave ether type change") Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Link: https://lore.kernel.org/netdev/78a8a03b-6070-3e6b-5042-f848dab16fb8@alu.unizg.hr/ Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function mlxfw_mfa2_tlv_multi_get() returns NULL if 'tlv' in
question does not pass checks in mlxfw_mfa2_tlv_payload_get(). This
behaviour may lead to NULL pointer dereference in 'multi->total_len'.
Fix this issue by testing mlxfw_mfa2_tlv_multi_get()'s return value
against NULL.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
The driver does not support PTP on these older chips and it is assuming
that firmware on these older chips will not return the
PORT_MAC_PTP_QCFG_RESP_FLAGS_HWRM_ACCESS flag in __bnxt_hwrm_ptp_qcfg(),
causing the function to abort quietly.
But newer firmware now sets this flag and so __bnxt_hwrm_ptp_qcfg()
will proceed further. Eventually it will fail in bnxt_ptp_init() ->
bnxt_map_ptp_regs() because there is no code to support the older chips.
The driver will then complain:
"PTP initialization failed.\n"
Fix it so that we abort quietly earlier without going through the
unnecessary steps and alarming the user with the warning log.
Fixes: ae5c42f0b92c ("bnxt_en: Get PTP hardware capability from firmware") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add error handling of i40e_setup_misc_vector() in i40e_rebuild().
In case interrupt vectors setup fails do not re-open vsi-s and
do not bring up vf-s, we have no interrupts to serve a traffic
anyway.
Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix accessing vsi->active_filters without holding the mac_filter_hash_lock.
Move vsi->active_filters = 0 inside critical section and
move clear_bit(__I40E_VSI_OVERFLOW_PROMISC, vsi->state) after the critical
section to ensure the new filters from other threads can be added only after
filters cleaning in the critical section is finished.
Fixes: 278e7d0b9d68 ("i40e: store MAC/VLAN filters in a hash with the MAC Address as key") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the NIC is down, user set mac address or vlan tag to VF,
the xxx_set_vf_mac() or xxx_set_vf_vlan() will invoke efx_net_stop()
and efx_net_open(), since netif_running() is false, the port will not
start and keep port_enabled false, but selftest_work is scheduled
in efx_net_open().
If we remove the device before selftest_work run, the efx_stop_port()
will not be called since the NIC is down, and then efx is freed,
we will soon get a UAF in run_timer_softirq() like this:
If the NIC is not actually brought up, there is no need to schedule
selftest_work, so let's move invoking efx_selftest_async_start()
into efx_start_all(), and it will be canceled by broughting down.
Fixes: dd40781e3a4e ("sfc: Run event/IRQ self-test asynchronously when interface is brought up") Fixes: e340be923012 ("sfc: add ndo_set_vf_mac() function for EF10") Debugged-by: Huang Cun <huangcun@sangfor.com.cn> Cc: Donglin Peng <pengdonglin@sangfor.com.cn> Suggested-by: Martin Habets <habetsm.xilinx@gmail.com> Signed-off-by: Ding Hui <dinghui@sangfor.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Here we copy the data from the original buf to the new page. But we
not check that it may be overflow.
As long as the size received(including vnethdr) is greater than 3840
(PAGE_SIZE -VIRTIO_XDP_HEADROOM). Then the memcpy will overflow.
And this is completely possible, as long as the MTU is large, such
as 4096. In our test environment, this will cause crash. Since crash is
caused by the written memory, it is meaningless, so I do not include it.
Fixes: 72979a6c3590 ("virtio_net: xdp, add slowpath case for non contiguous buffers") Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log