In commit a44be64bbecb ("ext4: don't clear SB_RDONLY when remounting
r/w until quota is re-enabled") we defer clearing tyhe SB_RDONLY flag
in struct super. However, we didn't defer when we checked sb_rdonly()
to determine the lazy itable init thread should be enabled, with the
next result that the lazy inode table initialization would not be
properly started. This can cause generic/231 to fail in ext4's
nojournal mode.
Fix this by moving when we decide to start or stop the lazy itable
init thread to after we clear the SB_RDONLY flag when we are
remounting the file system read/write.
Fixes a44be64bbecb ("ext4: don't clear SB_RDONLY when remounting r/w until...")
Instead of using the SMBIOS type 1 record 'family' field, which is often
modified by OEMs, use the type 4 'processor ID' and 'processor version'
fields, which are set to a small set of probe-able values on all known
Ampere EFI systems in the field.
Fixes: 550b33cfd4452968 ("arm64: efi: Force the use of ...") Tested-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receive buffer is small, or the TCP rx queue looks too
complicated to bother using it directly - we allocate a new
skb and copy data into it.
We already use sk->sk_allocation... but nothing actually
sets it to GFP_ATOMIC on the ->sk_data_ready() path.
Users of HW offload are far more likely to experience problems
due to scheduling while atomic. "Copy mode" is very rarely
triggered with SW crypto.
Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser") Tested-by: Shai Amiram <samiram@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fuzzed image contains an AGF with an obviously garbage
agf_refcount_level value of 32, and a dirty log with a buffer log item
for that AGF. The ondisk AGF has a higher LSN than the recovered log
item. xlog_recover_buf_commit_pass2 reads the buffer, compares the
LSNs, and decides to skip replay because the ondisk buffer appears to be
newer.
Unfortunately, the ondisk buffer is corrupt, but recovery just read the
buffer with no buffer ops specified:
Skipping the buffer leaves its contents in memory unverified. This sets
us up for a kernel crash because xfs_refcount_recover_cow_leftovers
reads the buffer (which is still around in XBF_DONE state, so no read
verification) and creates a refcountbt cursor of height 32. This is
impossible so we run off the end of the cursor object and crash.
Fix this by invoking the verifier on all skipped buffers and aborting
log recovery if the ondisk buffer is corrupt. It might be smarter to
force replay the log item atop the buffer and then see if it'll pass the
write verifier (like ext4 does) but for now let's go with the
conservative option where we stop immediately.
At drm suspend sequence, MST dc_sink is removed. When commit cached
MST stream back in drm resume sequence, the MST stream payload is not
properly created and added into the payload table. After resume, topology
change is reprobed by removing existing streams first. That leads to
no payload is found in the existing payload table as below error
"[drm] ERROR No payload for [MST PORT:] found in mst state"
1. In encoder .atomic_check routine, remove check existance of dc_sink
2. Bypass MST by checking existence of MST root port. dc_link_type cannot
differentiate MST port before topology is rediscovered.
Reviewed-by: Wayne Lin <wayne.lin@amd.com> Acked-by: Tom Chung <chiahsuan.chung@amd.com> Signed-off-by: Fangzhi Zuo <jerry.zuo@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
[Adjusted for variables that were renamed between 6.1 and 6.3.] Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IOMMU v2 page table supports 4 level (47 bit) or 5 level (56 bit) virtual
address space. Current code assumes it can support 64bit IOVA address
space. If IOVA allocator allocates virtual address > 47/56 bit (depending
on page table level) then it will do wrong mapping and cause invalid
translation.
Hence adjust aperture size to use max address supported by the page table.
Reported-by: Jerry Snitselaar <jsnitsel@redhat.com> Fixes: aaac38f61487 ("iommu/amd: Initial support for AMD IOMMU v2 page table") Cc: <Stable@vger.kernel.org> # v6.0+ Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20230518054351.9626-1-vasant.hegde@amd.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
[ Modified to work with "V2 with 4 level page table" only - Vasant ] Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TIS interrupt handler at least has to read and write the interrupt
status register. In case of SPI both operations result in a call to
tpm_tis_spi_transfer() which uses the bus_lock_mutex of the spi device
and thus must only be called from a sleepable context.
To ensure this request a threaded interrupt handler.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Tested-by: Michael Niewöhner <linux@mniewoehner.de> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when regmap_raw_write() splits the data, it uses the
max_raw_write value defined for the bus. For any bus that includes
the target register address in the max_raw_write value, the chunked
transmission will always exceed the maximum transmission length.
To avoid this problem, subtract the length of the register and the
padding from the maximum transmission.
Log load and replay is part of the metadata handle flow during mount
operation. The $MFT record will be loaded and used while replaying logs.
However, a malformed $MFT record, say, has RECORD_FLAG_DIR flag set and
contains an ATTR_ROOT attribute will misguide kernel to treat it as a
directory, and try to free the allocated resources when the
corresponding inode is freed, which will cause an invalid kfree because
the memory hasn't actually been allocated.
Commit ac4e97abce9b8 ("scatterlist: sg_set_buf() argument must be in linear
mapping") checks that both the signature and the digest reside in the
linear mapping area.
However, more recently commit ba14a194a434c ("fork: Add generic vmalloced
stack support") made it possible to move the stack in the vmalloc area,
which is not contiguous, and thus not suitable for sg_set_buf() which needs
adjacent pages.
Always make a copy of the signature and digest in the same buffer used to
store the key and its parameters, and pass them to sg_init_one(). Prefer it
to conditionally doing the copy if necessary, to keep the code simple. The
buffer allocated with kmalloc() is in the linear mapping area.
Check the remaining data length before accessing the context structure
to ensure that the entire structure is contained within the packet.
Additionally, since the context data length `ctxt_len` has already been
checked against the total packet length `len_of_ctxts`, update the
comparison to use `ctxt_len`.
Cc: stable@vger.kernel.org Signed-off-by: Kuan-Ting Chen <h3xrabbit@gmail.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If opinfo->conn is another connection and while ksmbd send oplock break
request to cient on current connection, The connection for opinfo->conn
can be disconnect and conn could be freed. When sending oplock break
request, this ksmbd_conn can be used and cause user-after-free issue.
When getting opinfo from the list, ksmbd check connection is being
released. If it is not released, Increase ->r_count to wait that connection
is freed.
Cc: stable@vger.kernel.org Reported-by: Per Forlin <per.forlin@axis.com> Tested-by: Per Forlin <per.forlin@axis.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix the failure from smb2.credits.single_req_credits_granted
test. When client send 8192 credit request, ksmbd return 8191 credit
granted. ksmbd should give maximum possible credits that must be granted
within the range of not exceeding the max credit to client.
Cc: stable@vger.kernel.org Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increment vcpu->stat.exits when handling a fastpath VM-Exit without
going through any part of the "slow" path. Not bumping the exits stat
can result in wildly misleading exit counts, e.g. if the primary reason
the guest is exiting is to program the TSC deadline timer.
When handling ESR_ELx_EC_WATCHPT_LOW, far_el2 member of struct
kvm_vcpu_fault_info will be copied to far member of struct
kvm_debug_exit_arch and exposed to the userspace. The userspace will
see stale values from older faults if the fault info does not get
populated.
Fixes: 8fb2046180a0 ("KVM: arm64: Move early handlers to per-EC handlers") Suggested-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230530024651.10014-1-akihiko.odaki@daynix.com Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note that the size 1024 corresponds to the size of the test firmware
buffer. The actual number of the buffers leaked is around 70-110,
depending on the test run.
The cause of the leak is the following:
request_partial_firmware_into_buf() and request_firmware_into_buf()
provided firmware buffer isn't released on release_firmware(), we
have allocated it and we are responsible for deallocating it manually.
This is introduced in a number of context where previously only
release_firmware() was called, which was insufficient.
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Fixes: 7feebfa487b92 ("test_firmware: add support for request_firmware_into_buf") Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Dan Carpenter <error27@gmail.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Russ Weight <russell.h.weight@intel.com> Cc: Tianfei zhang <tianfei.zhang@intel.com> Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Zhengchao Shao <shaozhengchao@huawei.com> Cc: Colin Ian King <colin.i.king@gmail.com> Cc: linux-kernel@vger.kernel.org Cc: Kees Cook <keescook@chromium.org> Cc: Scott Branden <sbranden@broadcom.com> Cc: Luis R. Rodriguez <mcgrof@kernel.org> Cc: linux-kselftest@vger.kernel.org Cc: stable@vger.kernel.org # v5.4 Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Link: https://lore.kernel.org/r/20230509084746.48259-3-mirsad.todorovac@alu.unizg.hr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter spotted that test_fw_config->reqs will be leaked if
trigger_batched_requests_store() is called two or more times.
The same appears with trigger_batched_requests_async_store().
This bug wasn't trigger by the tests, but observed by Dan's visual
inspection of the code.
The recommended workaround was to return -EBUSY if test_fw_config->reqs
is already allocated.
Fixes: 7feebfa487b92 ("test_firmware: add support for request_firmware_into_buf") Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Russ Weight <russell.h.weight@intel.com> Cc: Tianfei Zhang <tianfei.zhang@intel.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Colin Ian King <colin.i.king@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: linux-kselftest@vger.kernel.org Cc: stable@vger.kernel.org # v5.4 Suggested-by: Dan Carpenter <error27@gmail.com> Suggested-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Link: https://lore.kernel.org/r/20230509084746.48259-2-mirsad.todorovac@alu.unizg.hr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kallsyms_lookup() which in turn calls kallsyms_lookup_buildid() writes
to index "KSYM_NAME_LEN - 1".
Thus the array passed as namebuf to kallsyms_lookup() should be
KSYM_NAME_LEN in size.
In xmon.c the array was defined to be "128" bytes directly, without
using KSYM_NAME_LEN. Commit b8a94bfb3395 ("kallsyms: increase maximum
kernel symbol length to 512") changed the value to 512, but missed
updating the xmon code.
Fixes: b8a94bfb3395 ("kallsyms: increase maximum kernel symbol length to 512") Cc: stable@vger.kernel.org # v6.1+ Co-developed-by: Onkarnath <onkarnath.1@samsung.com> Signed-off-by: Onkarnath <onkarnath.1@samsung.com> Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
[mpe: Tweak change log wording and fix commit reference] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230529111337.352990-2-maninder1.s@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: null-ptr-deref in soft_cursor+0x384/0x6b4 drivers/video/fbdev/core/softcursor.c:70
Read of size 16 at addr 0000000000000200 by task kworker/u4:1/12
Treat i_data_sem for ea_inodes as being in their own lockdep class to
avoid lockdep complaints about ext4_setattr's use of inode_lock() on
normal inodes potentially causing lock ordering with i_data_sem on
ea_inodes in ext4_xattr_inode_write(). However, ea_inodes will be
operated on by ext4_setattr(), so this isn't a problem.
An ea_inode stores the value of an extended attribute; it can not have
extended attributes itself, or this will cause recursive nightmares.
Add a check in ext4_iget() to make sure this is the case.
If the ea_inode has been pushed out of the inode cache while there is
still a reference in the mb_cache, the lockdep subclass will not be
set on the inode, which can lead to some lockdep false positives.
Add a new flag, EXT4_IGET_EA_INODE which indicates whether the inode
is expected to have the EA_INODE flag or not. If the flag is not
set/clear as expected, then fail the iget() operation and mark the
file system as corrupted.
This commit also makes the ext4_iget() always perform the
is_bad_inode() check even when the inode is already inode cache. This
allows us to remove the is_bad_inode() check from the callers of
ext4_iget() in the ea_inode code.
Active subflow are inserted into the connection list at creation time.
When the MPJ handshake completes successfully, a new subflow creation
netlink event is generated correctly, but the current code wrongly
avoid initializing a couple of subflow data.
The above will cause misbehavior on a few exceptional events: unneeded
mptcp-level retransmission on msk-level sequence wrap-around and infinite
mapping fallback even when a MPJ socket is present.
Address the issue factoring out the needed initialization in a new helper
and invoking the latter from __mptcp_finish_join() time for passive
subflow and from mptcp_finish_join() for active ones.
Fixes: 0530020a7c8f ("mptcp: track and update contiguous data status") Cc: stable@vger.kernel.org Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ondrej reported a functional issue WRT timeout handling on connect
with a nice reproducer.
The problem is that the current mptcp connect waits for both the
MPTCP socket level timeout, and the first subflow socket timeout.
The latter is not influenced/touched by the exposed setsockopt().
Overall the above makes the SO_SNDTIMEO a no-op on connect.
Since mptcp_connect is invoked via inet_stream_connect and the
latter properly handle the MPTCP level timeout, we can address the
issue making the nested subflow level connect always unblocking.
This also allow simplifying a bit the code, dropping an ugly hack
to handle the fastopen and custom proto_ops connect.
The issues predates the blamed commit below, but the current resolution
requires the infrastructure introduced there.
Fixes: 54f1944ed6d2 ("mptcp: factor out mptcp_connect()") Reported-by: Ondrej Mosnacek <omosnace@redhat.com> Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/399 Cc: stable@vger.kernel.org Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Selftests are supposed to run on any kernels, including the old ones not
supporting MPTCP.
A new check is then added to make sure MPTCP is supported. If not, the
test stops and is marked as "skipped". Note that this check can also
mark the test as failed if 'SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES' env
var is set to 1: by doing that, we can make sure a test is not being
skipped by mistake.
A new shared file is added here to be able to re-used the same check in
the different selftests we have.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 048d19d444be ("mptcp: add basic kselftest for mptcp") Cc: stable@vger.kernel.org Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All callers of trace_probe_primary_from_call() check the return
value to be non NULL. However, the function returns
list_first_entry(&tpe->probes, ...) which can never be NULL.
Additionally, it does not check for the list being possibly empty,
possibly causing a type confusion on empty lists.
Use list_first_entry_or_null() which solves both problems.
Link: https://lore.kernel.org/linux-trace-kernel/20230128-list-entry-null-check-v1-1-8bde6a3da2ef@diag.uniroma1.it/ Fixes: 60d53e2c3b75 ("tracing/probe: Split trace_event related data from trace_probe") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Acked-by: Mukesh Ojha <quic_mojha@quicinc.com> Cc: stable@vger.kernel.org Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modifiers are used to change the behavior of keys. For instance, they
can grouped into buckets, converted to syscall names (from the syscall
identifier), show task->comm of the current pid, be an array of longs
that represent a stacktrace, and more.
It was found that nothing stopped a value from taking a modifier. As
values are simple counters. If this happened, it would call code that
was not expecting a modifier and crash the kernel. This was fixed by
having the ___create_val_field() function test if a modifier was present
and fail if one was. This fixed the crash.
Now there's a problem with variables. Variables are used to pass fields
from one event to another. Variables are allowed to have some modifiers,
as the processing may need to happen at the time of the event (like
stacktraces and comm names of the current pid). The issue is that it too
uses __create_val_field(). Now that fails on modifiers, variables can no
longer use them (this is a regression).
As not all modifiers are for variables, have them use a separate check.
Link: https://lore.kernel.org/linux-trace-kernel/20230523221108.064a5d82@rorschach.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Tom Zanussi <zanussi@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Fixes: e0213434fe3e4 ("tracing: Do not let histogram values have some modifiers") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing rtla timerlat auto analysis, I reach a condition where
the interface was not receiving tracing data. I was able to manually
reproduce the problem with these steps:
Then, trying to enable tracing again with echo 1 > tracing_on resulted
in no change: the trace was still not tracing.
This problem happens because the timerlat IRQ hits the stop tracing
condition while tracing is off, and do not wake up the timerlat thread,
so the timerlat threads are kept sleeping forever, resulting in no
trace, even after re-enabling the tracer.
Avoid this condition by always waking up the threads, even after stopping
tracing, allowing the tracer to return to its normal operating after
a new tracing on.
The addition of the mtdchar_read_ioctl() function caused the stack usage
of mtdchar_ioctl() to grow beyond the warning limit on 32-bit architectures
with gcc-13:
drivers/mtd/mtdchar.c: In function 'mtdchar_ioctl':
drivers/mtd/mtdchar.c:1229:1: error: the frame size of 1488 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Mark both the read and write portions as noinline_for_stack to ensure
they don't get inlined and use separate stack slots to reduce the
maximum usage, both in the mtdchar_ioctl() and combined with any
of its callees.
The Linux Kernel currently only requires make v3.82 while the grouped
target functionality requires make v4.3. Removed the grouped target
introduced in 4ce1f694eb5d ("selinux: ensure av_permissions.h is
built when needed") as well as the multiple header file targets in
the make rule. This effectively reverts the problem commit.
We will revisit this change when make >= 4.3 is required by the rest
of the kernel.
Cc: stable@vger.kernel.org Fixes: 4ce1f694eb5d ("selinux: ensure av_permissions.h is built when needed") Reported-by: Erwan Velu <e.velu@criteo.com> Reported-by: Luiz Capitulino <luizcap@amazon.com> Tested-by: Luiz Capitulino <luizcap@amazon.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For RISC-V, when tracing with tracepoint events, the IP and status are
set to 0, preventing the perf code parsing the callchain and resolving
the symbols correctly.
The fix is to implement perf_arch_fetch_caller_regs for riscv, which
fills several necessary registers used for callchain unwinding,
including epc, sp, s0 and status. It's similar to commit b3eac0265bf6
("arm: perf: Fix callchain parse error with kernel tracepoint events")
and commit 5b09a094f2fb ("arm64: perf: Fix callchain parse error with
kernel tracepoint events").
With this patch, callchain can be parsed correctly as:
With commit 858e8b792d06 ("tpm, tpm_tis: Avoid cache incoherency in test
for interrupts") bit accessor functions are used to access flags in
tpm_tis_data->flags.
However these functions expect bit numbers, while the flags are defined
as bit masks in enum tpm_tis_flag.
Fix this inconsistency by using numbers instead of masks also for the
flags in the enum.
Reported-by: Pavel Machek <pavel@denx.de> Fixes: 858e8b792d06 ("tpm, tpm_tis: Avoid cache incoherency in test for interrupts") Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Cc: stable@vger.kernel.org Reviewed-by: Pavel Machek <pavel@denx.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running on an AMD vIOMMU, we observed multiple invalidations (of
decreasing power of 2 aligned sizes) when unmapping a single page.
Domain flush takes gather bounds (end-start) as size param. However,
gather->end is defined as the last inclusive address (start + size - 1).
This leads to an off by 1 error.
With this patch, verified that 1 invalidation occurs when unmapping a
single page.
Fixes: a270be1b3fdf ("iommu/amd: Use only natural aligned flushes in a VM") Cc: stable@vger.kernel.org # >= 5.15 Signed-off-by: Jon Pan-Doh <pandoh@google.com> Tested-by: Sudheer Dantuluri <dantuluris@google.com> Suggested-by: Gary Zibrat <gzibrat@google.com> Reviewed-by: Vasant Hegde <vasant.hegde@amd.com> Acked-by: Nadav Amit <namit@vmware.com> Link: https://lore.kernel.org/r/20230426203256.237116-1-pandoh@google.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in tce_freemulti_pSeriesLP() there is no limit on how many
TCEs are passed to the H_STUFF_TCE hcall. This has not caused an issue
until now, but newer firmware releases have started enforcing a limit of
512 TCEs per call.
The limit is correct per the specification (PAPR v2.12 § 14.5.4.2.3).
The code has been in it's current form since it was initially merged.
Cc: stable@vger.kernel.org Signed-off-by: Gaurav Batra <gbatra@linux.vnet.ibm.com> Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
[mpe: Tweak change log wording & add PAPR reference] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230525143454.56878-1-gbatra@linux.vnet.ibm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scsi driver function sd_read_block_characteristics() always calls
disk_set_zoned() to a disk zoned model correctly, in case the device
model changed. This is done even for regular disks to set the zoned
model to BLK_ZONED_NONE and free any zone related resources if the drive
previously was zoned.
This behavior significantly impact the time it takes to revalidate disks
on a large system as the call to disk_clear_zone_settings() done from
disk_set_zoned() for the BLK_ZONED_NONE case results in the device
request queued to be frozen, even if there are no zone resources to
free.
Avoid this overhead for non-zoned devices by not calling
disk_clear_zone_settings() in disk_set_zoned() if the device model
was already set to BLK_ZONED_NONE, which is always the case for regular
devices.
Reported by: Brian Bunker <brian@purestorage.com>
Fixes: 508aebb80527 ("block: introduce blk_queue_clear_zone_settings()") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20230529073237.1339862-1-dlemoal@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The init counter is not decremented on initialisation errors, which
prevents retrying initialisation and can lead to the runtime suspend
callback attempting to disable resources that have never been enabled.
Add the missing decrement on initialisation errors so that the counter
reflects the state of the device.
When compiling on a MIPS 64-bit machine we get these warnings:
In file included from ./arch/mips/include/asm/cacheflush.h:13,
from ./include/linux/cacheflush.h:5,
from ./include/linux/highmem.h:8,
from ./include/linux/bvec.h:10,
from ./include/linux/blk_types.h:10,
from ./include/linux/blkdev.h:9,
from fs/btrfs/disk-io.c:7:
fs/btrfs/disk-io.c: In function ‘csum_tree_block’:
fs/btrfs/disk-io.c:100:34: error: array subscript 1 is above array bounds of ‘struct page *[1]’ [-Werror=array-bounds]
100 | kaddr = page_address(buf->pages[i]);
| ~~~~~~~~~~^~~
./include/linux/mm.h:2135:48: note: in definition of macro ‘page_address’
2135 | #define page_address(page) lowmem_page_address(page)
| ^~~~
cc1: all warnings being treated as errors
We can check if i overflows to solve the problem. However, this doesn't make
much sense, since i == 1 and num_pages == 1 doesn't execute the body of the loop.
In addition, i < num_pages can also ensure that buf->pages[i] will not cross
the boundary. Unfortunately, this doesn't help with the problem observed here:
gcc still complains.
To fix this add a compile-time condition for the extent buffer page
array size limit, which would eventually lead to eliminating the whole
for loop.
CC: stable@vger.kernel.org # 5.10+ Signed-off-by: pengfuyuan <pengfuyuan@kylinos.cn> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPUART IP now has two known bugs, one is that CTS has higher priority
than the break signal, which causes the break signal sending through
UARTCTRL_SBK may impacted by the CTS input if the HW flow control is
enabled. It exists on all platforms we support in this driver.
So we add a workaround patch for this issue: commit c4c81db5cf8b
("tty: serial: fsl_lpuart: disable the CTS when send break signal").
Another IP bug is i.MX8QM LPUART may have an additional break character
being sent after SBK was cleared. It may need to add some delay between
clearing SBK and re-enabling CTS to ensure that the SBK latch are
completely cleared.
But we found that during the delay period before CTS is enabled, there
is still a risk that Bluetooth data in TX FIFO may be sent out during
this period because of break off and CTS disabled(even if BT sets CTS
line deasserted, data is still sent to BT).
Due to this risk, we have to drop the CTS-disabling workaround for SBK
bugs, use TXINV seems to be a better way to replace SBK feature and
avoid above risk. Also need to disable the transmitter to prevent any
data from being sent out during break, then invert the TX line to send
break. Then disable the TXINV when turn off break and re-enable
transmitter.
Fixes: c4c81db5cf8b ("tty: serial: fsl_lpuart: disable the CTS when send break signal") Cc: stable <stable@kernel.org> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230519094751.28948-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chapter "5.3 Power-Up/Down Sequence" of WILC1000 [1] and WILC3000 [2]
states that CHIP_EN must be pulled HIGH first, RESETN second. Fix the
order of these signals in the driver.
Use the mmc_pwrseq_ops as driver data as the delay between signals is
specific to SDIO card type anyway.
We may get an empty response with zero length at the beginning of
the driver start and get following UBSAN error. Since there is no
content(SDRT_NONE) for the response, just return and skip the response
handling to avoid this problem.
Test pass : SDIO wifi throughput test with this patch
90b926e68f50 ("x86/pat: Fix pat_x_mtrr_type() for MTRR disabled case")
broke the use case of running Xen dom0 kernels on machines with an
external disk enclosure attached via USB, see Link tag.
What this commit was originally fixing - SEV-SNP guests on Hyper-V - is
a more specialized situation which has other issues at the moment anyway
so reverting this now and addressing the issue properly later is the
prudent thing to do.
So revert it in time for the 6.2 proper release.
[ bp: Rewrite commit message. ]
Reported-by: Christian Kujau <lists@nerdbynature.de> Tested-by: Christian Kujau <lists@nerdbynature.de> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/r/4fe9541e-4d4c-2b2a-f8c8-2d34a7284930@nerdbynature.de Cc: Jason Andryuk <jandryuk@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk for renoir.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels are
given the reversed orders by PMFW. Like the memory DPM clocks
that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverses the DPM clocks levels output of pp_dpm_mclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For devices not attached to a port multiplier and managed directly by
libata, the device number passed to ata_find_dev() must always be lower
than the maximum number of devices returned by ata_link_max_devices().
That is 1 for SATA devices or 2 for an IDE link with master+slave
devices. This device number is the SCSI device ID which matches these
constraints as the IDs are generated per port and so never exceed the
maximum number of devices for the link being used.
However, for libsas managed devices, SCSI device IDs are assigned per
struct scsi_host, leading to device IDs for SATA devices that can be
well in excess of libata per-link maximum number of devices. This
results in ata_find_dev() to always return NULL for libsas managed
devices except for the first device of the target scsi_host with ID
(device number) equal to 0. This issue is visible by executing the
hdparm utility, which fails. E.g.:
hdparm -i /dev/sdX
/dev/sdX:
HDIO_GET_IDENTITY failed: No message of desired type
Fix this by rewriting ata_find_dev() to ignore the device number for
non-PMP attached devices with a link with at most 1 device, that is SATA
devices. For these, the device number 0 is always used to
return the correct pointer to the struct ata_device of the port link.
This change excludes IDE master/slave setups (maximum number of devices
per link is 2) and port-multiplier attached devices. Also, to be
consistant with the fact that SCSI device IDs and channel numbers used
as device numbers are both unsigned int, change the devno argument of
ata_find_dev() to unsigned int.
Reported-by: Xingui Yang <yangxingui@huawei.com> Fixes: 41bda9c98035 ("libata-link: update hotplug to handle PMP links") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc 13 may assign another type to enumeration constants than gcc 12. Split
the large enum at the top of source file stex.c such that the type of the
constants used in time expressions is changed back to the same type chosen
by gcc 12. This patch suppresses compiler warnings like this one:
In file included from ./include/linux/bitops.h:7,
from ./include/linux/kernel.h:22,
from drivers/scsi/stex.c:13:
drivers/scsi/stex.c: In function ‘stex_common_handshake’:
./include/linux/typecheck.h:12:25: error: comparison of distinct pointer types lacks a cast [-Werror]
12 | (void)(&__dummy == &__dummy2); \
| ^~
./include/linux/jiffies.h:106:10: note: in expansion of macro ‘typecheck’
106 | typecheck(unsigned long, b) && \
| ^~~~~~~~~
drivers/scsi/stex.c:1035:29: note: in expansion of macro ‘time_after’
1035 | if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
| ^~~~~~~~~~
See also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405.
Cc: stable@vger.kernel.org Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20230529195034.3077-1-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The channel's rpmsg object allows new invocations to be made. After old
invocations are already interrupted, the driver shouldn't try to invoke
anymore. Invalidating the rpmsg at the end of the driver removal
function makes it easy to cause a race condition in userspace. Even
closing a file descriptor before the driver finishes its cleanup can
cause an invocation via fastrpc_release_current_dsp_process() and
subsequent timeout.
Invalidate the channel before the invocations are interrupted to make
sure that no invocations can be created to hang after the device closes.
Fixes: c68cfb718c8f ("misc: fastrpc: Add support for context Invoke method") Cc: stable <stable@kernel.org> Signed-off-by: Richard Acayan <mailingradian@gmail.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20230523152550.438363-5-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value is initialized as -1, or -EPERM. The completion of an
invocation implies that the return value is set appropriately, but
"Permission denied" does not accurately describe the outcome of the
invocation. Set the invocation's return value to a more appropriate
"Broken pipe", as the cleanup breaks the driver's connection with rpmsg.
'end_sector' is compared to 'rdev->recovery_offset', which is offset to
rdev, however, commit e82ed3a4fbb5 ("md/raid6: refactor
raid5_read_one_chunk") changes the calculation of 'end_sector' to offset
to the array. Fix this miscalculation.
Fixes: e82ed3a4fbb5 ("md/raid6: refactor raid5_read_one_chunk") Cc: stable@vger.kernel.org # v5.12+ Signed-off-by: Yu Kuai <yukuai3@huawei.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20230524014118.3172781-1-yukuai1@huaweicloud.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While exercising the unbind path, with the current implementation
the functionfs_unbind would be calling which waits for the ffs->mutex
to be available, however within the same time ffs_ep0_read is invoked
& if no setup packets are pending, it will invoke function
wait_event_interruptible_exclusive_locked_irq which by definition waits
for the ev.count to be increased inside the same mutex for which
functionfs_unbind is waiting.
This creates deadlock situation because the functionfs_unbind won't
get the lock until ev.count is increased which can only happen if
the caller ffs_func_unbind can proceed further.
Expected speed should be bigger than 300Mbits/sec.
The root cause of this performance drop was found to be data corruption
happening at 4K borders in some Ethernet packets, leading to TCP
checksum errors. This corruption occurs from the position
(4K - (address & 0x7F)) to 4K. The u_ether function's allocation of
skb_buff reserves 64B, meaning all RX addresses resemble 0xXXXX0040.
Commit 28d1a7ac2a0d ("iio: dac: Add AD5758 support") adds the config AD5758
and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver
is however included when AD5755 is selected, not when AD5758 is selected.
Probably, this was simply a mistake that happened by copy-and-paste and
forgetting to adjust the actual line. Surprisingly, no one has ever noticed
that this driver is actually only included when AD5755 is selected and that
the config AD5758 has actually no effect on the build.
The AD7192 provides a specific channel configuration where both negative
and positive inputs are connected to AIN2. This was represented in the
ad7192 driver as a IIO channel with .channel = 2 and .extended_name set
to "shorted".
The problem with this approach, is that the driver provided two IIO
channels with the identifier .channel = 2; one "shorted" and the other
not. This goes against the IIO ABI, as a channel identifier should be
unique.
Address this issue by changing "shorted" channels to being differential
instead, with channel 2 vs. itself, as we're actually measuring AIN2 vs.
itself.
Note that the fix tag is for the commit that moved the driver out of
staging. The bug existed before that, but backporting would become very
complex further down and unlikely to happen.
Fixes: b581f748cce0 ("staging: iio: adc: ad7192: move out of staging") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Co-developed-by: Alisa Roman <alisa.roman@analog.com> Signed-off-by: Alisa Roman <alisa.roman@analog.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20230330102100.17590-1-paul@crapouillou.net Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On success, ad74413r_get_single_adc_result() returns IIO_VAL_INT aka
1. So currently, the IIO_CHAN_INFO_PROCESSED case is effectively
equivalent to the IIO_CHAN_INFO_RAW case, and we never call
ad74413r_adc_to_resistance_result() to convert the adc measurement to
ohms.
Check ret for being negative rather than non-zero.
The i2c_master_send() returns number of sent bytes on success,
or negative on error. The suspend/resume callbacks expect zero
on success and non-zero on error. Adapt the return value of the
i2c_master_send() to the expectation of the suspend and resume
callbacks, including proper validation of the return value.
The Sigma-Delta ADCs supported by this driver can use SDO as an interrupt
line to indicate the completion of a conversion. However, some devices
cannot properly detect the completion of a conversion by an interrupt.
This is for the reason mentioned in the following commit.
commit e9849777d0e2 ("genirq: Add flag to force mask in
disable_irq[_nosync]()")
A read operation is performed by an extra interrupt before the completion
of a conversion. At this time, the value read from the ADC data register
is the same as the previous conversion result. This patch fixes the issue
by setting IRQ_DISABLE_UNLAZY flag.
Fixes: 55707294c4eb ("iio: light: Add support for vishay vcnl4035") Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20230501143605.1615549-1-Frank.Li@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Timestamp reset is not done in the correct place. It must be done
before enabling buffer. The reason is that interrupt timestamping
is always happening when the chip is on, even if the
corresponding sensor is off. When the sensor restarts, timestamp
is wrong if you don't do a reset first.
If high bit is set to 1 in ((data[3] & 0x0f << 28), after all arithmetic
operations and integer promotions are done, high bits in
wacom->serial[idx] will be filled with 1s as well.
Avoid this, albeit unlikely, issue by specifying left operand's __u64
type for the right operand.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f85e ("iio: adc: mxs-lradc: Add support for ADC driver") Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When apply_acpi_orientation() fails, st_accel_common_probe() will fall back
to iio_read_mount_matrix(), which checks for a mount-matrix device property
and if that is not set falls back to the identity matrix.
But when a sensor has no ACPI companion fwnode, or when the ACPI fwnode
does not have a "_ONT" method apply_acpi_orientation() was returning 0,
causing iio_read_mount_matrix() to never get called resulting in an
invalid mount_matrix:
When the uvcvideo driver encounters a format descriptor with an unknown
format GUID, it creates a corresponding struct uvc_format instance with
the fcc field set to 0. Since commit 50459f103edf ("media: uvcvideo:
Remove format descriptions"), the driver relies on the V4L2 core to
provide the format description string, which the V4L2 core can't do
without a valid 4CC. This triggers a WARN_ON.
As a format with a zero 4CC can't be selected, it is unusable for
applications. Ignore the format completely without creating a uvc_format
instance, which fixes the warning.
While building the shared_cpu_map, check if the cache level and cache
type matches. On certain systems that build the cache topology based on
the instance ID, there are cases where the same ID may repeat across
multiple cache levels, leading inaccurate topology.
In event of CPU offlining, the cache_shared_cpu_map_remove() does not
consider if IDs at same level are being compared. As a result, when same
IDs repeat across different cache levels, the CPU going offline is not
removed from all the shared_cpu_map.
Below is the output of cache topology of CPU8 and it's SMT sibling after
CPU8 is offlined on a dual socket 3rd Generation AMD EPYC processor
(2 x 64C/128T) running kernel release v6.3:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu136/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu136/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list: 9-15,136-143
CPU8 is removed from index0 (L1i) but remains in the shared_cpu_list of
index1 (L1d) and index2 (L2). Since L1i, L1d, and L2 are shared by the
SMT siblings, and they have the same cache instance ID, CPU 2 is only
removed from the first index with matching ID which is index1 (L1i) in
this case. With this fix, the results are as expected when performing
the same experiment on the same system:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu136/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index1/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index2/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list: 9-15,136-143
When rebuilding topology, the same problem appears as
cache_shared_cpu_map_setup() implements a similar logic. Consider the
same 3rd Generation EPYC processor: CPUs in Core 1, that share the L1
and L2 caches, have L1 and L2 instance ID as 1. For all the CPUs on
the second chiplet, the L3 ID is also 1 leading to grouping on CPUs from
Core 1 (1, 17) and the entire second chiplet (8-15, 24-31) as CPUs
sharing one cache domain. This went undetected since x86 processors
depended on arch specific populate_cache_leaves() method to repopulate
the shared_cpus_map when CPU came back online until kernel release
v6.3-rc5.
Fixes: 198102c9103f ("cacheinfo: Fix shared_cpu_map to handle shared caches at different levels") Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Link: https://lore.kernel.org/r/20230508084115.1157-2-kprateek.nayak@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When VCODEC_CAPABILITY_4K_DISABLED is not set in dec_capability, skip
formats that are not MTK_FMT_DEC so only decoder formats is updated in
mtk_init_vdec_params.
Fixes: e25528e1dbe5 ("media: mediatek: vcodec: Use 4K frame size when supported by stateful decoder") Signed-off-by: Pin-yen Lin <treapking@chromium.org> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Yunfei Dong <yunfei.dong@mediatek.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Note that the current report, which can be triggered by the vgic_irq
kselftest, is a triple chain that includes slots_lock, but after
inverting the slots_lock/config_lock dependency, the actual problem
reported above remains.
In several places, the vgic code calls kvm_io_bus_register_dev(), which
synchronizes the srcu, while holding config_lock (#1). And the MMIO
handler takes the config_lock while holding the srcu read lock (#0).
Break dependency #1, by registering the distributor and redistributors
without holding config_lock. The ITS also uses kvm_io_bus_register_dev()
but already relies on slots_lock to serialize calls.
The distributor iodev is created on the first KVM_RUN call. Multiple
threads will race for vgic initialization, and only the first one will
see !vgic_ready() under the lock. To serialize those threads, rely on
slots_lock rather than config_lock.
Redistributors are created earlier, through KVM_DEV_ARM_VGIC_GRP_ADDR
ioctls and vCPU creation. Similarly, serialize the iodev creation with
slots_lock, and the rest with config_lock.
Fixes: f00327731131 ("KVM: arm64: Use config_lock to protect vgic state") Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Reviewed-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20230518100914.2837292-2-jean-philippe@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
User should not be able to write block device if it is read-only at
block level (e.g force_ro attribute). This is ensured in the regular
fops write operation (blkdev_write_iter) but not when writing via
user mapping (mmap), allowing user to actually write a read-only
block device via a PROT_WRITE mapping.
Example: This can lead to integrity issue of eMMC boot partition
(e.g mmcblk0boot0) which is read-only by default.
To fix this issue, simply deny shared writable mapping if the block
is readonly.
Note: Block remains writable if switch to read-only is performed
after the initial mapping, but this is expected behavior according
to commit a32e236eb93e ("Partially revert "block: fail op_is_write()
requests to read-only partitions"")'.
Add a quirk for Teamgroup MP33 that reports duplicate ids for disk.
Signed-off-by: Daniel Smith <dansmith@ds.gy>
[kch: patch formatting] Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com> Tested-by: Daniel Smith <dansmith@ds.gy> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When handling UBLK_IO_FETCH_REQ, ctx->uring_lock is grabbed first, then
ub->mutex is acquired.
When handling UBLK_CMD_STOP_DEV or UBLK_CMD_DEL_DEV, ub->mutex is
grabbed first, then calling io_uring_cmd_done() for canceling uring
command, in which ctx->uring_lock may be required.
Real deadlock only happens when all the above commands are issued from
same uring context, and in reality different uring contexts are often used
for handing control command and IO command.
Fix the issue by using io_uring_cmd_complete_in_task() to cancel command
in ublk_cancel_dev(ublk_cancel_queue).
When performing device unbind or halt, we have disabled all irqs at the
very begining like amdgpu_pci_remove or amdgpu_device_halt. So
amdgpu_irq_put for irqs stored in fence driver should not be called
any more, otherwise, below calltrace will arrive.
When CONFIG_PROC_FS is disabled, the function declarations for some
procfs functions are hidden, but the definitions are still build,
as shown by this compiler warning:
net/atm/resources.c:403:7: error: no previous prototype for 'atm_dev_seq_start' [-Werror=missing-prototypes]
net/atm/resources.c:409:6: error: no previous prototype for 'atm_dev_seq_stop' [-Werror=missing-prototypes]
net/atm/resources.c:414:7: error: no previous prototype for 'atm_dev_seq_next' [-Werror=missing-prototypes]
Add another #ifdef to leave these out of the build.
projects / linux-stable / log