On some systems amd_pinconf_set() is called with parameters
0x8 (PIN_CONFIG_DRIVE_PUSH_PULL) or 0x14 (PIN_CONFIG_PERSIST_STATE)
which are not supported by pinctrl-amd.
Don't show an err message when called with an invalid parameter,
downgrade this to debug instead.
Cc: stable@vger.kernel.org # 6.1 Fixes: 635a750d958e1 ("pinctrl: amd: Use amd_pinconf_set() for all config options") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20230717201652.17168-1-mario.limonciello@amd.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According the "USB Type-C Port Controller Interface Specification v2.0"
the TCPC sets the fault status register bit-7
(AllRegistersResetToDefault) once the registers have been reset to
their default values.
This triggers an alert(-irq) on PTN5110 devices albeit we do mask the
fault-irq, which may cause a kernel hang. Fix this generically by writing
a one to the corresponding bit-7.
A syzbot stress test using a corrupted disk image reported that
mark_buffer_dirty() called from __nilfs_mark_inode_dirty() or
nilfs_palloc_commit_alloc_entry() may output a kernel warning, and can
panic if the kernel is booted with panic_on_warn.
This is because nilfs2 keeps buffer pointers in local structures for some
metadata and reuses them, but such buffers may be forcibly discarded by
nilfs_clear_dirty_page() in some critical situations.
This issue is reported to appear after commit 28a65b49eb53 ("nilfs2: do
not write dirty data after degenerating to read-only"), but the issue has
potentially existed before.
Fix this issue by checking the uptodate flag when attempting to reuse an
internally held buffer, and reloading the metadata instead of reusing the
buffer if the flag was lost.
Link: https://lkml.kernel.org/r/20230818131804.7758-1-konishi.ryusuke@gmail.com Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+cdfcae656bac88ba0e2d@syzkaller.appspotmail.com Closes: https://lkml.kernel.org/r/0000000000003da75f05fdeffd12@google.com Fixes: 8c26c4e2694a ("nilfs2: fix issue with flush kernel thread after remount in RO mode because of driver's internal error or metadata corruption") Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> # 3.10+ Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A syzbot stress test reported that create_empty_buffers() called from
nilfs_lookup_dirty_data_buffers() can cause a general protection fault.
Analysis using its reproducer revealed that the back reference "mapping"
from a page/folio has been changed to NULL after dirty page/folio gang
lookup in nilfs_lookup_dirty_data_buffers().
Fix this issue by excluding pages/folios from being collected if, after
acquiring a lock on each page/folio, its back reference "mapping" differs
from the pointer to the address space struct that held the page/folio.
When partner does not support get_status message, tcpm right now
responds with soft reset message. This causes PD renegotiation to
happen and resets PPS link. Avoid soft resetting the link when
partner does not support get_status message to mitigate PPS resets.
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
The operating-performance-point vote needs to be dropped when shutting
down the port to avoid wasting power by keeping resources like power
domains in an unnecessarily high performance state (e.g. when a UART
connected Bluetooth controller is not in use).
Fixes: a5819b548af0 ("tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state") Cc: stable@vger.kernel.org # 5.9 Cc: Rajendra Nayak <quic_rjendra@quicinc.com> Cc: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20230714130214.14552-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
txs may be dropped if the frame is aggregated in AMSDU. When the problem
shows up, some SKBs would be hold in driver to cause network stopped
temporarily. Even if the problem can be recovered by txs timeout handling,
mt7921 still need to disable txs in AMSDU to avoid this issue.
Cc: stable@vger.kernel.org Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support") Reviewed-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In btsdio_probe, the data->work is bound with btsdio_work. It will be
started in btsdio_send_frame.
If the btsdio_remove runs with a unfinished work, there may be a race
condition that hdev is freed but used in btsdio_work. Fix it by
canceling the work before do cleanup in btsdio_remove.
Fixes: CVE-2023-1989 Fixes: ddbaf13e3609 ("[Bluetooth] Add generic driver for Bluetooth SDIO devices") Cc: stable@vger.kernel.org Signed-off-by: Zheng Wang <zyytlz.wz@163.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
[ Denis: Added CVE-2023-1989 and fixes tags. ] Signed-off-by: Denis Efremov (Oracle) <efremov@linux.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In probe function, request_firmware_nowait() is called to load firmware
asynchronously. At completion of firmware loading, register_netdev() is
called. However, a mutex needed by netdev is initialized after the call
to request_firmware_nowait(). Consequently, it can happen that
register_netdev() is called before the driver is ready.
Move the mutex initialization into r8712_init_drv_sw(), which is called
before request_firmware_nowait().
Reported-by: syzbot+b08315e8cf5a78eed03c@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-staging/000000000000d9d4560601b8e0d7@google.com/T/#u Fixes: 8c213fa59199 ("staging: r8712u: Use asynchronous firmware loading") Cc: stable <stable@kernel.org> Signed-off-by: Nam Cao <namcaov@gmail.com> Link: https://lore.kernel.org/r/20230731110620.116562-1-namcaov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the EKR battery remains even after we stop getting information
from the device. This can lead to a stale battery persisting indefinitely
in userspace.
The remote sends a heartbeat every 10 seconds. Delete the battery if we
miss two heartbeats (after 21 seconds). Restore the battery once we see
a heartbeat again.
Signed-off-by: Aaron Skomra <skomra@gmail.com> Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com> Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com> Fixes: 9f1015d45f62 ("HID: wacom: EKR: attach the power_supply on first connection") CC: stable@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current driver, the value of tuning parameter will not take effect
if samsung,picophy-* is assigned as 0. Because 0 is also a valid value
acccording to the description of USB_PHY_CFG1 register, this will improve
the logic to let it work.
Fixes: 58a3cefb3840 ("usb: chipidea: imx: add two samsung picophy parameters tuning implementation")
cc: <stable@vger.kernel.org> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20230627112126.1882666-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device connected to usb otg port of GXL-based boards can not be
recognised after resumption, doesn't recover even if disconnect and
reconnect the device. dmesg shows it disconnects during resumption.
[ 41.492911] usb 1-2: USB disconnect, device number 3
[ 41.499346] usb 1-2: unregistering device
[ 41.511939] usb 1-2: unregistering interface 1-2:1.0
Calling usb_post_init() will fix this issue, and it's tested and
verified on libretech's aml-s905x-cc board.
Cc: stable@vger.kernel.org # v5.8+ Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue") Signed-off-by: Luke Lu <luke.lu@libre.computer> Acked-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20230809212911.18903-1-luke.lu@libre.computer Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been reports of USB-audio driver spewing errors at the
probe time on a few devices like Jabra and Logitech. The suggested
fix there couldn't be applied as is, unfortunately, because it'll
likely break other devices.
But, the patch suggested an interesting point: looking at the current
init code in stream.c, one may notice that it does initialize
differently from the device setup in endpoint.c. Namely, for UAC1, we
should call snd_usb_init_pitch() and snd_usb_init_sample_rate() after
setting the interface, while the init sequence at parsing calls them
before setting the interface blindly.
This patch changes the init sequence at parsing for UAC1 (and other
devices that need a similar behavior) to be aligned with the rest of
the code, setting the interface at first. And, this fixes the
long-standing problems on a few UAC1 devices like Jabra / Logitech,
as reported, too.
It has recently come to my attention that nvidia is circumventing the
protection added in 262e6ae7081d ("modules: inherit
TAINT_PROPRIETARY_MODULE") by importing exports from their proprietary
modules into an allegedly GPL licensed module and then rexporting them.
Given that symbol_get was only ever intended for tightly cooperating
modules using very internal symbols it is logical to restrict it to
being used on EXPORT_SYMBOL_GPL and prevent nvidia from costly DMCA
Circumvention of Access Controls law suites.
All symbols except for four used through symbol_get were already exported
as EXPORT_SYMBOL_GPL, and the remaining four ones were switched over in
the preparation patches.
ds1685_rtc_poweroff is only used externally via symbol_get, which was
only ever intended for very internal symbols like this one. Use
EXPORT_SYMBOL_GPL for it so that symbol_get can enforce only being used
on EXPORT_SYMBOL_GPL symbols.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Joshua Kinard <kumba@gentoo.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
enetc_phc_index is only used via symbol_get, which was only ever
intended for very internal symbols like this one. Use EXPORT_SYMBOL_GPL
for it so that symbol_get can enforce only being used on
EXPORT_SYMBOL_GPL symbols.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
au1xmmc is split somewhat awkwardly into the main mmc subsystem driver,
and callbacks in platform_data that sit under arch/mips/ and are
always built in. The latter than call mmc_detect_change through
symbol_get. Remove the use of symbol_get by requiring the driver
to be built in. In the future the interrupt handlers for card
insert/eject detection should probably be moved into the main driver,
and which point it can be built modular again.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Manuel Lauss <manuel.lauss@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
[mcgrof: squashed in depends on MMC=y suggested by Arnd] Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spitz board file uses the obscure symbol_get() function
to optionally call a function from sharpsl_pm.c if that is
built. However, the two files are always built together
these days, and have been for a long time, so this can
be changed to a normal function call.
Link: https://lore.kernel.org/lkml/20230731162639.GA9441@lst.de/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If authblob->SessionKey.Length is bigger than session key
size(CIFS_KEY_SIZE), slub overflow can happen in key exchange codes.
cifs_arc4_crypt copy to session key array from SessionKey from client.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21940 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ->DataOffset of create context is 0, DataBuffer size is not correctly
validated. This patch change wrong validation code and consider tag
length in request.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21824 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was accidentally fixed up in commit e4c1cf523d82 but we can't
take the full change due to other dependancy issues, so here is just
the actual bugfix that is needed.
[Background]
keltargw reported an issue [1] that with mmaped I/Os, sometimes the
tail of the last page (after file ends) is not filled with zeroes.
The root cause is that such tail page could be wrongly selected for
inplace I/Os so the zeroed part will then be filled with compressed
data instead of zeroes.
A simple fix is to avoid doing inplace I/Os for such tail parts,
actually that was already fixed upstream in commit e4c1cf523d82
("erofs: tidy up z_erofs_do_read_page()") by accident.
thunderbolt: Fix a backport error for display flickering issue
A mistake was made when backporting commit 583893a66d73 ("thunderbolt: Fix
Thunderbolt 3 display flickering issue on 2nd hot plug onwards") in missing
the `if` block. Add it back in.
Reported-by: Joakim.Tjernlund@infinera.com Closes: https://lore.kernel.org/stable/28b5d0accce90bedf2f75d65290c5a1302225f0f.camel@infinera.com/ Fixes: 06614ca4f18e ("thunderbolt: Fix Thunderbolt 3 display flickering issue on 2nd hot plug onwards") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernel test robot reported a kallsyms_test failure when clang lto is
enabled (thin or full) and CONFIG_KALLSYMS_SELFTEST is also enabled.
I can reproduce in my local environment with the following error message
with thin lto:
[ 1.877897] kallsyms_selftest: Test for 1750th symbol failed: (tsc_cs_mark_unstable) addr=ffffffff81038090
[ 1.877901] kallsyms_selftest: abort
It appears that commit 8cc32a9bbf29 ("kallsyms: strip LTO-only suffixes
from promoted global functions") caused the failure. Commit 8cc32a9bbf29
changed cleanup_symbol_name() based on ".llvm." instead of '.' where
".llvm." is appended to a before-lto-optimization local symbol name.
We need to propagate such knowledge in kallsyms_selftest.c as well.
Further more, compare_symbol_name() in kallsyms.c needs change as well.
In scripts/kallsyms.c, kallsyms_names and kallsyms_seqs_of_names are used
to record symbol names themselves and index to symbol names respectively.
For example:
kallsyms_names:
...
__amd_smn_rw._entry <== seq 1000
__amd_smn_rw._entry.5 <== seq 1001
__amd_smn_rw.llvm.<hash> <== seq 1002
...
kallsyms_seqs_of_names are sorted based on cleanup_symbol_name() through, so
the order in kallsyms_seqs_of_names actually has
index 1000: seq 1002 <== __amd_smn_rw.llvm.<hash> (actual symbol comparison using '__amd_smn_rw')
index 1001: seq 1000 <== __amd_smn_rw._entry
index 1002: seq 1001 <== __amd_smn_rw._entry.5
Let us say at a particular point, at index 1000, symbol '__amd_smn_rw.llvm.<hash>'
is comparing to '__amd_smn_rw._entry' where '__amd_smn_rw._entry' is the one to
search e.g., with function kallsyms_on_each_match_symbol(). The current implementation
will find out '__amd_smn_rw._entry' is less than '__amd_smn_rw.llvm.<hash>' and
then continue to search e.g., index 999 and never found a match although the actual
index 1001 is a match.
To fix this issue, let us do cleanup_symbol_name() first and then do comparison.
In the above case, comparing '__amd_smn_rw' vs '__amd_smn_rw._entry' and
'__amd_smn_rw._entry' being greater than '__amd_smn_rw', the next comparison will
be > index 1000 and eventually index 1001 will be hit an a match is found.
For any symbols not having '.llvm.' substr, there is no functionality change
for compare_symbol_name().
Fixes: 8cc32a9bbf29 ("kallsyms: strip LTO-only suffixes from promoted global functions") Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202308232200.1c932a90-oliver.sang@intel.com Signed-off-by: Yonghong Song <yonghong.song@linux.dev> Reviewed-by: Song Liu <song@kernel.org> Reviewed-by: Zhen Lei <thunder.leizhen@huawei.com> Link: https://lore.kernel.org/r/20230825034659.1037627-1-yonghong.song@linux.dev Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Mon, 28 Aug 2023 21:55:55 +0000 (23:55 +0200)]
io_uring/parisc: Adjust pgoff in io_uring mmap() for parisc
Vidra Jonas reported issues on parisc with libuv which then triggers
build errors with cmake. Debugging shows that those issues stem from
io_uring().
I was not able to easily pull in upstream commits directly, so here
is IMHO the least invasive manual backport of the following upstream
commits to fix the cache aliasing issues on parisc on kernel 6.1
with io_uring:
56675f8b9f9b ("io_uring/parisc: Adjust pgoff in io_uring mmap() for parisc") 32832a407a71 ("io_uring: Fix io_uring mmap() by using architecture-provided get_unmapped_area()") d808459b2e31 ("io_uring: Adjust mapping wrt architecture aliasing requirements")
With this patch kernel 6.1 has all relevant mmap changes and is
identical to kernel 6.5 with regard to mmap() in io_uring.
Signed-off-by: Helge Deller <deller@gmx.de> Reported-by: Vidra.Jonas@seznam.cz Link: https://lore.kernel.org/linux-parisc/520.NvTX.6mXZpmfh4Ju.1awpAS@seznam.cz/ Cc: Sam James <sam@gentoo.org> Cc: John David Anglin <dave.anglin@bell.net> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change simplifies the randomization of file mapping regions. It
reworks the code to remove duplication. The flow is now similar to
that for mips. Finally, we consistently use the do_color_align variable
to determine when color alignment is needed.
Tested on rp3440.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the parisc architecture, lockdep reports for all static objects which
are in the __initdata section (e.g. "setup_done" in devtmpfs,
"kthreadd_done" in init/main.c) this warning:
INFO: trying to register non-static key.
The warning itself is wrong, because those objects are in the __initdata
section, but the section itself is on parisc outside of range from
_stext to _end, which is why the static_obj() functions returns a wrong
answer.
While fixing this issue, I noticed that the whole existing check can
be simplified a lot.
Instead of checking against the _stext and _end symbols (which include
code areas too) just check for the .data and .bss segments (since we check a
data object). This can be done with the existing is_kernel_core_data()
macro.
In addition objects in the __initdata section can be checked with
init_section_contains(), and is_kernel_rodata() allows keys to be in the
_ro_after_init section.
This partly reverts and simplifies commit bac59d18c701 ("x86/setup: Fix static
memory detection").
Today module_frob_arch_sections() spots init sections from their
'init' prefix, and uses this to keep the init PLTs separate from the rest.
get_module_plt() uses within_module_init() to determine if a
location is in the init text or not, but this depends on whether
core code thought this was an init section.
Naturally the logic is different.
module_init_layout_section() groups the init and exit text together if
module unloading is disabled, as the exit code will never run. The result
is kernels with this configuration can't load all their modules because
there are not enough PLTs for the combined init+exit section.
A previous patch exposed module_init_layout_section(), use that so the
logic is the same.
Fixes: 055f23b74b20 ("module: check for exit sections in layout_sections() instead of module_init_section()") Cc: stable@vger.kernel.org Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today module_frob_arch_sections() spots init sections from their
'init' prefix, and uses this to keep the init PLTs separate from the rest.
module_emit_plt_entry() uses within_module_init() to determine if a
location is in the init text or not, but this depends on whether
core code thought this was an init section.
Naturally the logic is different.
module_init_layout_section() groups the init and exit text together if
module unloading is disabled, as the exit code will never run. The result
is kernels with this configuration can't load all their modules because
there are not enough PLTs for the combined init+exit section.
module_init_layout_section() choses whether the core module loader
considers a section as init or not. This affects the placement of the
exit section when module unloading is disabled. This code will never run,
so it can be free()d once the module has been initialised.
arm and arm64 need to count the number of PLTs they need before applying
relocations based on the section name. The init PLTs are stored separately
so they can be free()d. arm and arm64 both use within_module_init() to
decide which list of PLTs to use when applying the relocation.
Because within_module_init()'s behaviour changes when module unloading
is disabled, both architecture would need to take this into account when
counting the PLTs.
Today neither architecture does this, meaning when module unloading is
disabled there are insufficient PLTs in the init section to load some
modules, resulting in warnings:
| WARNING: CPU: 2 PID: 51 at arch/arm64/kernel/module-plts.c:99 module_emit_plt_entry+0x184/0x1cc
| Modules linked in: crct10dif_common
| CPU: 2 PID: 51 Comm: modprobe Not tainted 6.5.0-rc4-yocto-standard-dirty #15208
| Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
| pstate: 20400005 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : module_emit_plt_entry+0x184/0x1cc
| lr : module_emit_plt_entry+0x94/0x1cc
| sp : ffffffc0803bba60
[...]
| Call trace:
| module_emit_plt_entry+0x184/0x1cc
| apply_relocate_add+0x2bc/0x8e4
| load_module+0xe34/0x1bd4
| init_module_from_file+0x84/0xc0
| __arm64_sys_finit_module+0x1b8/0x27c
| invoke_syscall.constprop.0+0x5c/0x104
| do_el0_svc+0x58/0x160
| el0_svc+0x38/0x110
| el0t_64_sync_handler+0xc0/0xc4
| el0t_64_sync+0x190/0x194
Instead of duplicating module_init_layout_section()s logic, expose it.
Reported-by: Adam Johnston <adam.johnston@arm.com> Fixes: 055f23b74b20 ("module: check for exit sections in layout_sections() instead of module_init_section()") Cc: stable@vger.kernel.org Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `nocrt` module parameter has no code associated with it and does
nothing. As `crt=-1` has same functionality as what nocrt should be
doing drop `nocrt` and associated documentation.
This should fix a quirk for Gigabyte GA-7ZX that used `nocrt` and
thus didn't function properly.
Fixes: 8c99fdce3078 ("ACPI: thermal: set "thermal.nocrt" via DMI on Gigabyte GA-7ZX") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vangogh driver just gained a link time dependency that now causes
randconfig builds to fail:
x86_64-linux-ld: sound/soc/amd/vangogh/pci-acp5x.o: in function `snd_acp5x_probe':
pci-acp5x.c:(.text+0xbb): undefined reference to `snd_amd_acp_find_config'
Fixes: e89f45edb747e ("ASoC: amd: vangogh: Add check for acp config flags in vangogh platform") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20230605085839.2157268-1-arnd@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation of append may cause duplicate data and/or
incorrect ranges to be returned to a reader during an update. Although
this has not been reported or seen, disable the append write operation
while the tree is in rcu mode out of an abundance of caution.
During the analysis of the mas_next_slot() the following was
artificially created by separating the writer and reader code:
Writer: reader:
mas_wr_append
set end pivot
updates end metata
Detects write to last slot
last slot write is to start of slot
store current contents in slot
overwrite old end pivot
mas_next_slot():
read end metadata
read old end pivot
return with incorrect range
store new value
Alternatively:
Writer: reader:
mas_wr_append
set end pivot
updates end metata
Detects write to last slot
last lost write to end of slot
store value
mas_next_slot():
read end metadata
read old end pivot
read new end pivot
return with incorrect range
set old end pivot
There may be other accesses that are not safe since we are now updating
both metadata and pointers, so disabling append if there could be rcu
readers is the safest action.
Link: https://lkml.kernel.org/r/20230819004356.1454718-2-Liam.Howlett@oracle.com Fixes: 54a611b60590 ("Maple Tree: add new data structure") Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Associate the swnode of the GPIO device's (which is the interrupt
controller here) with the irq domain. Otherwise the interrupt-controller
device attribute is a no-op.
Fixes: cb8c474e79be ("gpio: sim: new testing module") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a GPIO simulator device is unbound with interrupts still requested,
we will hit a use-after-free issue in __irq_domain_deactivate_irq(). The
owner of the irq domain must dispose of all mappings before destroying
the domain object.
Fixes: cb8c474e79be ("gpio: sim: new testing module") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a signal callback releases the sw_sync fence, that will trigger a
deadlock as the timeline_fence_release recurses onto the fence->lock
(used both for signaling and the the timeline tree).
To avoid that, temporarily hold an extra reference to the signalled
fences until after we drop the lock.
(This is an alternative implementation of https://patchwork.kernel.org/patch/11664717/
which avoids some potential UAF issues with the original patch.)
v2: Remove now obsolete comment, use list_move_tail() and
list_del_init()
Reported-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl> Fixes: d3c6dd1fb30d ("dma-buf/sw_sync: Synchronize signal vs syncpt free") Signed-off-by: Rob Clark <robdclark@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230818145939.39697-1-robdclark@gmail.com Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the below random NULL pointer crash during boot by serializing
pinctrl group and function creation/remove calls in
rzv2m_dt_subnode_to_map() with mutex lock.
Crash logs:
pc : __pi_strcmp+0x20/0x140
lr : pinmux_func_name_to_selector+0x68/0xa4
Call trace:
__pi_strcmp+0x20/0x140
pinmux_generic_add_function+0x34/0xcc
rzv2m_dt_subnode_to_map+0x2e4/0x418
rzv2m_dt_node_to_map+0x15c/0x18c
pinctrl_dt_to_map+0x218/0x37c
create_pinctrl+0x70/0x3d8
Fix the below random NULL pointer crash during boot by serializing
pinctrl group and function creation/remove calls in
rzg2l_dt_subnode_to_map() with mutex lock.
Crash log:
pc : __pi_strcmp+0x20/0x140
lr : pinmux_func_name_to_selector+0x68/0xa4
Call trace:
__pi_strcmp+0x20/0x140
pinmux_generic_add_function+0x34/0xcc
rzg2l_dt_subnode_to_map+0x314/0x44c
rzg2l_dt_node_to_map+0x164/0x194
pinctrl_dt_to_map+0x218/0x37c
create_pinctrl+0x70/0x3d8
While at it, add comments for bitmap_lock and lock.
The COMMON_CLK config is not enabled in some of the architectures.
This causes below build issues:
pwm-rz-mtu3.c:(.text+0x114):
undefined reference to `clk_rate_exclusive_put'
pwm-rz-mtu3.c:(.text+0x32c):
undefined reference to `clk_rate_exclusive_get'
Fix these issues by moving clk_rate_exclusive_{get,put} inside COMMON_CLK
code block, as clk.c is enabled by COMMON_CLK.
Fixes: 55e9b8b7b806 ("clk: add clk_rate_exclusive api") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/all/202307251752.vLfmmhYm-lkp@intel.com/ Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Link: https://lore.kernel.org/r/20230725175140.361479-1-biju.das.jz@bp.renesas.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The raid_component_add() function was added to the kernel tree via patch
"[SCSI] embryonic RAID class" (2005). Remove this function since it never
has had any callers in the Linux kernel. And also raid_component_release()
is only used in raid_component_add(), so it is also removed.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com> Link: https://lore.kernel.org/r/20230822015254.184270-1-wangzhu9@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Fixes: 04b5b5cb0136 ("scsi: core: Fix possible memory leak if device_add() fails") Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 41320b18a0e0 ("scsi: snic: Fix possible memory leak if device_add()
fails") fixed the memory leak caused by dev_set_name() when device_add()
failed. However, it did not consider that 'tgt' has already been released
when put_device(&tgt->dev) is called. Remove kfree(tgt) in the error path
to avoid double free of 'tgt' and move put_device(&tgt->dev) after the
removed kfree(tgt) to avoid a use-after-free.
Fixes: 41320b18a0e0 ("scsi: snic: Fix possible memory leak if device_add() fails") Signed-off-by: Zhu Wang <wangzhu9@huawei.com> Link: https://lore.kernel.org/r/20230819083941.164365-1-wangzhu9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 98b211d6415f ("madvise: convert madvise_free_pte_range() to use a
folio") replaced the page_mapcount() with folio_mapcount() to check
whether the folio is shared by other mapping.
It's not correct for large folios. folio_mapcount() returns the total
mapcount of large folio which is not suitable to detect whether the folio
is shared.
Use folio_estimated_sharers() which returns a estimated number of shares.
That means it's not 100% correct. It should be OK for madvise case here.
User-visible effects is that the THP is skipped when user call madvise.
But the correct behavior is THP should be split and processed then.
NOTE: this change is a temporary fix to reduce the user-visible effects
before the long term fix from David is ready.
Link: https://lkml.kernel.org/r/20230808020917.2230692-4-fengwei.yin@intel.com Fixes: 98b211d6415f ("madvise: convert madvise_free_pte_range() to use a folio") Signed-off-by: Yin Fengwei <fengwei.yin@intel.com> Reviewed-by: Yu Zhao <yuzhao@google.com> Reviewed-by: Ryan Roberts <ryan.roberts@arm.com> Cc: David Hildenbrand <david@redhat.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ee8b94c8510c ("can: raw: fix receiver memory leak") introduced
a new reference to the CAN netdevice that has assigned CAN filters.
But this new ro->dev reference did not maintain its own refcount which
lead to another KASAN use-after-free splat found by Eric Dumazet.
This patch ensures a proper refcount for the CAN nedevice.
Fixes: ee8b94c8510c ("can: raw: fix receiver memory leak") Reported-by: Eric Dumazet <edumazet@google.com> Cc: Ziyang Xuan <william.xuanziyang@huawei.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/r/20230821144547.6658-3-socketcan@hartkopp.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, on unplug events, the TMU mode was disabled first
followed by the Time Synchronization Handshake, irrespective of
whether the tb_switch_tmu_rate_write() API was successful or not.
However, this caused a problem with Thunderbolt 3 (TBT3)
devices, as the TSPacketInterval bits were always enabled by default,
leading the host router to assume that the device router's TMU was
already enabled and preventing it from initiating the Time
Synchronization Handshake. As a result, TBT3 monitors experienced
display flickering from the second hot plug onwards.
To address this issue, we have modified the code to only disable the
Time Synchronization Handshake during TMU disable if the
tb_switch_tmu_rate_write() function is successful. This ensures that
the TBT3 devices function correctly and eliminates the display
flickering issue.
Co-developed-by: Sanath S <Sanath.S@amd.com> Signed-off-by: Sanath S <Sanath.S@amd.com> Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[ USB4v2 introduced support for uni-directional TMU mode as part of d49b4f043d63 ("thunderbolt: Add support for enhanced uni-directional TMU mode")
This is not a stable candidate commit, so adjust the code for backport. ] Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cpuset_can_attach() can fail. Postpone DL BW allocation until all tasks
have been checked. DL BW is not allocated per-task but as a sum over
all DL tasks migrating.
If multiple controllers are attached to the cgroup next to the cpuset
controller a non-cpuset can_attach() can fail. In this case free DL BW
in cpuset_cancel_attach().
Finally, update cpuset DL task count (nr_deadline_tasks) only in
cpuset_attach().
Suggested-by: Waiman Long <longman@redhat.com> Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Signed-off-by: Juri Lelli <juri.lelli@redhat.com> Reviewed-by: Waiman Long <longman@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Qais Yousef (Google) <qyousef@layalina.io> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While moving a set of tasks between exclusive cpusets,
cpuset_can_attach() -> task_can_attach() calls dl_cpu_busy(..., p) for
DL BW overflow checking and per-task DL BW allocation on the destination
root_domain for the DL tasks in this set.
This approach has the issue of not freeing already allocated DL BW in
the following error cases:
(1) The set of tasks includes multiple DL tasks and DL BW overflow
checking fails for one of the subsequent DL tasks.
(2) Another controller next to the cpuset controller which is attached
to the same cgroup fails in its can_attach().
To address this problem rework dl_cpu_busy():
(1) Split it into dl_bw_check_overflow() & dl_bw_alloc() and add a
dedicated dl_bw_free().
(2) dl_bw_alloc() & dl_bw_free() take a `u64 dl_bw` parameter instead of
a `struct task_struct *p` used in dl_cpu_busy(). This allows to
allocate DL BW for a set of tasks too rather than only for a single
task.
update_tasks_root_domain currently iterates over all tasks even if no
DEADLINE task is present on the cpuset/root domain for which bandwidth
accounting is being rebuilt. This has been reported to introduce 10+ ms
delays on suspend-resume operations.
Skip the costly iteration for cpusets that don't contain DEADLINE tasks.
Qais reported that iterating over all tasks when rebuilding root domains
for finding out which ones are DEADLINE and need their bandwidth
correctly restored on such root domains can be a costly operation (10+
ms delays on suspend-resume).
To fix the problem keep track of the number of DEADLINE tasks belonging
to each cpuset and then use this information (followup patch) to only
perform the above iteration if DEADLINE tasks are actually present in
the cpuset for which a corresponding root domain is being rebuilt.
Turns out percpu_cpuset_rwsem - commit 1243dc518c9d ("cgroup/cpuset:
Convert cpuset_mutex to percpu_rwsem") - wasn't such a brilliant idea,
as it has been reported to cause slowdowns in workloads that need to
change cpuset configuration frequently and it is also not implementing
priority inheritance (which causes troubles with realtime workloads).
Convert percpu_cpuset_rwsem back to regular cpuset_mutex. Also grab it
only for SCHED_DEADLINE tasks (other policies don't care about stable
cpusets anyway).
Signed-off-by: Juri Lelli <juri.lelli@redhat.com> Reviewed-by: Waiman Long <longman@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org>
[ Conflict in kernel/cgroup/cpuset.c due to pulling new code/comments.
Reject all new code. Remove BUG_ON() about rwsem that doesn't exist on
mainline. ] Signed-off-by: Qais Yousef (Google) <qyousef@layalina.io> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've aligned setgid behavior over multiple kernel releases. The details
can be found in commit cf619f891971 ("Merge tag 'fs.ovl.setgid.v6.2' of
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping") and
commit 426b4ca2d6a5 ("Merge tag 'fs.setgid.v6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux").
Consistent setgid stripping behavior is now encapsulated in the
setattr_should_drop_sgid() helper which is used by all filesystems that
strip setgid bits outside of vfs proper. Usually ATTR_KILL_SGID is
raised in e.g., chown_common() and is subject to the
setattr_should_drop_sgid() check to determine whether the setgid bit can
be retained. Since nfsd is raising ATTR_KILL_SGID unconditionally it
will cause notify_change() to strip it even if the caller had the
necessary privileges to retain it. Ensure that nfsd only raises
ATR_KILL_SGID if the caller lacks the necessary privileges to retain the
setgid bit.
Without this patch the setgid stripping tests in LTP will fail:
> As you can see, the problem is S_ISGID (0002000) was dropped on a
> non-group-executable file while chown was invoked by super-user, while
Reported-by: Sherry Yang <sherry.yang@oracle.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Reviewed-by: Jeff Layton <jlayton@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
[Harshit: backport to 6.1.y:
Use init_user_ns instead of nop_mnt_idmap as we don't have
commit abf08576afe3 ("fs: port vfs_*() helpers to struct mnt_idmap")] Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've aligned setgid behavior over multiple kernel releases. The details
can be found in the following two merge messages: cf619f891971 ("Merge tag 'fs.ovl.setgid.v6.2') 426b4ca2d6a5 ("Merge tag 'fs.setgid.v6.0')
Consistent setgid stripping behavior is now encapsulated in the
setattr_should_drop_sgid() helper which is used by all filesystems that
strip setgid bits outside of vfs proper. Switch nfs to rely on this
helper as well. Without this patch the setgid stripping tests in
xfstests will fail.
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de>
Message-Id: <20230313-fs-nfs-setgid-v2-1-9a59f436cfc0@kernel.org> Signed-off-by: Christian Brauner <brauner@kernel.org>
[ Harshit: backport to 6.1.y:
fs/internal.h -- minor conflict due to code change differences.
include/linux/fs.h -- Used struct user_namespace *mnt_userns
instead of struct mnt_idmap *idmap
fs/nfs/inode.c -- Used init_user_ns instead of nop_mnt_idmap ] Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some issues with the bpf/nat6to4.c building.
1. It use TEST_CUSTOM_PROGS, which will add the nat6to4.o to
kselftest-list file and run by common run_tests.
2. When building the test via `make -C tools/testing/selftests/
TARGETS="net"`, the nat6to4.o will be build in selftests/net/bpf/
folder. But in test udpgro_frglist.sh it refers to ../bpf/nat6to4.o.
The correct path should be ./bpf/nat6to4.o.
3. If building the test via `make -C tools/testing/selftests/ TARGETS="net"
install`. The nat6to4.o will be installed to kselftest_install/net/
folder. Then the udpgro_frglist.sh should refer to ./nat6to4.o.
To fix the confusing test path, let's just move the nat6to4.c to net folder
and build it as TEST_GEN_FILES.
Add a 200ms delay after sending a ctrl report to Quadro,
Octo, D5 Next and Aquaero to give them enough time to
process the request and save the data to memory. Otherwise,
under heavier userspace loads where multiple sysfs entries
are usually set in quick succession, a new ctrl report could
be requested from the device while it's still processing the
previous one and fail with -EPIPE. The delay is only applied
if two ctrl report operations are near each other in time.
Reported by a user on Github [1] and tested by both of us.
0-Day found a 34.6% regression in stress-ng's 'af-alg' test case, and
bisected it to commit b81fac906a8f ("x86/fpu: Move FPU initialization into
arch_cpu_finalize_init()"), which optimizes the FPU init order, and moves
the CR4_OSXSAVE enabling into a later place:
As the FPU is not yet initialized the CPU capability setup fails to set
X86_FEATURE_OSXSAVE. Many security module like 'camellia_aesni_avx_x86_64'
depend on this feature and therefore fail to load, causing the regression.
Cure this by setting X86_FEATURE_OSXSAVE feature right after OSXSAVE
enabling.
[ tglx: Moved it into the actual BSP FPU initialization code and added a comment ]
The thread flag TIF_NEED_FPU_LOAD indicates that the FPU saved state is
valid and should be reloaded when returning to userspace. However, the
kernel will skip doing this if the FPU registers are already valid as
determined by fpregs_state_valid(). The logic embedded there considers
the state valid if two cases are both true:
1: fpu_fpregs_owner_ctx points to the current tasks FPU state
2: the last CPU the registers were live in was the current CPU.
This is usually correct logic. A CPU’s fpu_fpregs_owner_ctx is set to
the current FPU during the fpregs_restore_userregs() operation, so it
indicates that the registers have been restored on this CPU. But this
alone doesn’t preclude that the task hasn’t been rescheduled to a
different CPU, where the registers were modified, and then back to the
current CPU. To verify that this was not the case the logic relies on the
second condition. So the assumption is that if the registers have been
restored, AND they haven’t had the chance to be modified (by being
loaded on another CPU), then they MUST be valid on the current CPU.
Besides the lazy FPU optimizations, the other cases where the FPU
registers might not be valid are when the kernel modifies the FPU register
state or the FPU saved buffer. In this case the operation modifying the
FPU state needs to let the kernel know the correspondence has been
broken. The comment in “arch/x86/kernel/fpu/context.h” has:
/*
...
* If the FPU register state is valid, the kernel can skip restoring the
* FPU state from memory.
*
* Any code that clobbers the FPU registers or updates the in-memory
* FPU state for a task MUST let the rest of the kernel know that the
* FPU registers are no longer valid for this task.
*
* Either one of these invalidation functions is enough. Invalidate
* a resource you control: CPU if using the CPU for something else
* (with preemption disabled), FPU for the current task, or a task that
* is prevented from running by the current task.
*/
However, this is not completely true. When the kernel modifies the
registers or saved FPU state, it can only rely on
__fpu_invalidate_fpregs_state(), which wipes the FPU’s last_cpu
tracking. The exec path instead relies on fpregs_deactivate(), which sets
the CPU’s FPU context to NULL. This was observed to fail to restore the
reset FPU state to the registers when returning to userspace in the
following scenario:
1. A task is executing in userspace on CPU0
- CPU0’s FPU context points to tasks
- fpu->last_cpu=CPU0
2. The task exec()’s
3. While in the kernel the task is preempted
- CPU0 gets a thread executing in the kernel (such that no other
FPU context is activated)
- Scheduler sets task’s fpu->last_cpu=CPU0 when scheduling out
4. Task is migrated to CPU1
5. Continuing the exec(), the task gets to
fpu_flush_thread()->fpu_reset_fpregs()
- Sets CPU1’s fpu context to NULL
- Copies the init state to the task’s FPU buffer
- Sets TIF_NEED_FPU_LOAD on the task
6. The task reschedules back to CPU0 before completing the exec() and
returning to userspace
- During the reschedule, scheduler finds TIF_NEED_FPU_LOAD is set
- Skips saving the registers and updating task’s fpu→last_cpu,
because TIF_NEED_FPU_LOAD is the canonical source.
7. Now CPU0’s FPU context is still pointing to the task’s, and
fpu->last_cpu is still CPU0. So fpregs_state_valid() returns true even
though the reset FPU state has not been restored.
So the root cause is that exec() is doing the wrong kind of invalidate. It
should reset fpu->last_cpu via __fpu_invalidate_fpregs_state(). Further,
fpu__drop() doesn't really seem appropriate as the task (and FPU) are not
going away, they are just getting reset as part of an exec. So switch to
__fpu_invalidate_fpregs_state().
Also, delete the misleading comment that says that either kind of
invalidate will be enough, because it’s not always the case.
Fixes: 33344368cb08 ("x86/fpu: Clean up the fpu__clear() variants") Reported-by: Lei Wang <lei4.wang@intel.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Lijun Pan <lijun.pan@intel.com> Reviewed-by: Sohil Mehta <sohil.mehta@intel.com> Acked-by: Lijun Pan <lijun.pan@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230818170305.502891-1-rick.p.edgecombe@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System wide suspend already has support for lmem save/restore during
suspend therefore enabling d3cold for s2idle and keepng it disable for
runtime PM.(Refer below commit for d3cold runtime PM disable justification)
'commit 66eb93e71a7a ("drm/i915/dgfx: Keep PCI autosuspend control
'on' by default on all dGPU")'
It will reduce the DG2 Card power consumption to ~0 Watt
for s2idle power KPI.
For multiple commands the driver was not correctly validating the shader
stages resulting in possible kernel oopses. The validation code was only.
if ever, checking the upper bound on the shader stages but never a lower
bound (valid shader stages start at 1 not 0).
40613da52b13 ("PCI: acpiphp: Reassign resources on bridge if necessary")
changed acpiphp hotplug to use pci_assign_unassigned_bridge_resources()
which depends on bridge being available, however enable_slot() can be
called without bridge associated:
1. Legitimate case of hotplug on root bus (widely used in virt world)
2. A (misbehaving) firmware, that sends ACPI Bus Check notifications to
non existing root ports (Dell Inspiron 7352/0W6WV0), which end up at
enable_slot(..., bridge = 0) where bus has no bridge assigned to it.
acpihp doesn't know that it's a bridge, and bus specific 'PCI
subsystem' can't augment ACPI context with bridge information since
the PCI device to get this data from is/was not available.
Issue is easy to reproduce with QEMU's 'pc' machine, which supports PCI
hotplug on hostbridge slots. To reproduce, boot kernel at commit 40613da52b13 in VM started with following CLI (assuming guest root fs is
installed on sda1 partition):
The issue was discovered on Dell Inspiron 7352/0W6WV0 laptop with following
sequence:
1. Suspend to RAM
2. Wake up with the same backtrace being observed:
3. 2nd suspend to RAM attempt makes laptop freeze
Fix it by using __pci_bus_assign_resources() instead of
pci_assign_unassigned_bridge_resources() as we used to do, but only in case
when bus doesn't have a bridge associated (to cover for the case of ACPI
event on hostbridge or non existing root port).
That lets us keep hotplug on root bus working like it used to and at the
same time keeps resource reassignment usable on root ports (and other 1st
level bridges) that was fixed by 40613da52b13.
Fixes: 40613da52b13 ("PCI: acpiphp: Reassign resources on bridge if necessary") Link: https://lore.kernel.org/r/20230726123518.2361181-2-imammedo@redhat.com Reported-by: Woody Suwalski <terraluna977@gmail.com> Tested-by: Woody Suwalski <terraluna977@gmail.com> Tested-by: Michal Koutný <mkoutny@suse.com> Link: https://lore.kernel.org/r/11fc981c-af49-ce64-6b43-3e282728bd1a@gmail.com Signed-off-by: Igor Mammedov <imammedo@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Rafael J. Wysocki <rafael@kernel.org> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
variable *nplanes is provided by user via system call argument. The
possible value of q_data->fmt->num_planes is 1-3, while the value
of *nplanes can be 1-8. The array access by index i can cause array
out-of-bounds.
Fix this bug by checking *nplanes against the array size.
Shubhra reports that their laptop is heating up over s2idle. Even though
it's getting into the deepest state, it appears to be having spurious
wakeup events.
While debugging a tangential issue with the RTC Carsten reports that recent
6.1.y based kernel face a similar problem.
Looking at acpidump and GPIO register comparisons these spurious wakeup
events are from the GPIO associated with the I2C touchpad on both laptops
and occur even when the touchpad is not marked as a wake source by the
kernel.
This means that the boot firmware has programmed these bits and because
Linux didn't touch them lead to spurious wakeup events from that GPIO.
To fix this issue, restore most of the code that previously would clear all
the bits associated with wakeup sources. This will allow the kernel to only
program the wake up sources that are necessary.
This is similar to what was done previously; but only the wake bits are
cleared by default instead of interrupts and wake bits. If any other
problems are reported then it may make sense to clear interrupts again too.
While originally it was fine to format strings using "%pOF" while
holding devtree_lock, this now causes a deadlock. Lockdep reports:
of_get_parent from of_fwnode_get_parent+0x18/0x24
^^^^^^^^^^^^^
of_fwnode_get_parent from fwnode_count_parents+0xc/0x28
fwnode_count_parents from fwnode_full_name_string+0x18/0xac
fwnode_full_name_string from device_node_string+0x1a0/0x404
device_node_string from pointer+0x3c0/0x534
pointer from vsnprintf+0x248/0x36c
vsnprintf from vprintk_store+0x130/0x3b4
Fix this by moving the printing in __of_changeset_entry_apply() outside
the lock. As the only difference in the multiple prints is the action
name, use the existing "action_names" to refactor the prints into a
single print.
Fixes: a92eb7621b9fb2c2 ("lib/vsprintf: Make use of fwnode API to obtain node names and separators") Cc: stable@vger.kernel.org Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20230801-dt-changeset-fixes-v3-2-5f0410e007dd@kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 12e17243d8a1 ("of: base: improve error msg in
of_phandle_iterator_next()") added printing of the phandle value on
error, but failed to update the unittest.
When building the kernel with binutils 2.37 and GCC-11.1.0/GCC-11.2.0,
the following error occurs:
Assembler messages:
Error: cannot find default versions of the ISA extension `zicsr'
Error: cannot find default versions of the ISA extension `zifencei'
The above error originated from this commit of binutils[0], which has been
resolved and backported by GCC-12.1.0[1] and GCC-11.3.0[2].
So fix this by change the GCC version in
CONFIG_TOOLCHAIN_NEEDS_OLD_ISA_SPEC to GCC-11.3.0.
Binutils-2.38 and GCC-12.1.0 bumped[0][1] the default ISA spec to the newer 20191213 version which moves some instructions from the I extension to the
Zicsr and Zifencei extensions. So if one of the binutils and GCC exceeds
that version, we should explicitly specifying Zicsr and Zifencei via -march
to cope with the new changes. but this only occurs when binutils >= 2.36
and GCC >= 11.1.0. It's a different story when binutils < 2.36.
binutils-2.36 supports the Zifencei extension[2] and splits Zifencei and
Zicsr from I[3]. GCC-11.1.0 is particular[4] because it add support Zicsr
and Zifencei extension for -march. binutils-2.35 does not support the
Zifencei extension, and does not need to specify Zicsr and Zifencei when
working with GCC >= 12.1.0.
To make our lives easier, let's relax the check to binutils >= 2.36 in
CONFIG_TOOLCHAIN_NEEDS_EXPLICIT_ZICSR_ZIFENCEI. For the other two cases,
where clang < 17 or GCC < 11.1.0, we will deal with them in
CONFIG_TOOLCHAIN_NEEDS_OLD_ISA_SPEC.
For more information, please refer to:
commit 6df2a016c0c8 ("riscv: fix build with binutils 2.38")
commit e89c2e815e76 ("riscv: Handle zicsr/zifencei issues between clang and binutils")
The gcc compiler translates on some architectures the 64-bit
__builtin_clzll() function to a call to the libgcc function __clzdi2(),
which should take a 64-bit parameter on 32- and 64-bit platforms.
But in the current kernel code, the built-in __clzdi2() function is
defined to operate (wrongly) on 32-bit parameters if BITS_PER_LONG ==
32, thus the return values on 32-bit kernels are in the range from
[0..31] instead of the expected [0..63] range.
This patch fixes the in-kernel functions __clzdi2() and __ctzdi2() to
take a 64-bit parameter on 32-bit kernels as well, thus it makes the
functions identical for 32- and 64-bit kernels.
This bug went unnoticed since kernel 3.11 for over 10 years, and here
are some possible reasons for that:
a) Some architectures have assembly instructions to count the bits and
which are used instead of calling __clzdi2(), e.g. on x86 the bsr
instruction and on ppc cntlz is used. On such architectures the
wrong __clzdi2() implementation isn't used and as such the bug has
no effect and won't be noticed.
b) Some architectures link to libgcc.a, and the in-kernel weak
functions get replaced by the correct 64-bit variants from libgcc.a.
c) __builtin_clzll() and __clzdi2() doesn't seem to be used in many
places in the kernel, and most likely only in uncritical functions,
e.g. when printing hex values via seq_put_hex_ll(). The wrong return
value will still print the correct number, but just in a wrong
formatting (e.g. with too many leading zeroes).
d) 32-bit kernels aren't used that much any longer, so they are less
tested.
A trivial testcase to verify if the currently running 32-bit kernel is
affected by the bug is to look at the output of /proc/self/maps:
Here the kernel uses a correct implementation of __clzdi2():
The automatic recalculation of the maximum allowed MTU is usually triggered
by code sections which are already rtnl lock protected by callers outside
of batman-adv. But when the fragmentation setting is changed via
batman-adv's own batadv genl family, then the rtnl lock is not yet taken.
But dev_set_mtu requires that the caller holds the rtnl lock because it
uses netdevice notifiers. And this code will then fail the check for this
lock:
RTNL: assertion failed at net/core/dev.c (1953)
Cc: stable@vger.kernel.org Reported-by: syzbot+f8812454d9b3ac00d282@syzkaller.appspotmail.com Fixes: c6a953cce8d0 ("batman-adv: Trigger events for auto adjusted MTU") Signed-off-by: Sven Eckelmann <sven@narfation.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230821-batadv-missing-mtu-rtnl-lock-v1-1-1c5a7bfe861e@narfation.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When batadv_v_ogm_aggr_send is called for an inactive interface, the skb
is silently dropped by batadv_v_ogm_send_to_if() but never freed causing
the following memory leak:
When a client roamed back to a node before it got time to destroy the
pending local entry (i.e. within the same originator interval) the old
global one is directly removed from hash table and left as such.
But because this entry had an extra reference taken at lookup (i.e using
batadv_tt_global_hash_find) there is no way its memory will be reclaimed
at any time causing the following memory leak:
If received skb in batadv_v_elp_packet_recv or batadv_v_ogm_packet_recv
is either cloned or non linearized then its data buffer will be
reallocated by batadv_check_management_packet when skb_cow or
skb_linearize get called. Thus geting ethernet header address inside
skb data buffer before batadv_check_management_packet had any chance to
reallocate it could lead to the following kernel panic:
If the user set an MTU value, it usually means that there are special
requirements for the MTU. But if an interface gots activated, the MTU was
always recalculated and then the user set value was overwritten.
The only reason why this user set value has to be overwritten, is when the
MTU has to be decreased because batman-adv is not able to transfer packets
with the user specified size.
If an interface changes the MTU, it is expected that an NETDEV_PRECHANGEMTU
and NETDEV_CHANGEMTU notification events is triggered. This worked fine for
.ndo_change_mtu based changes because core networking code took care of it.
But for auto-adjustments after hard-interfaces changes, these events were
simply missing.
Due to this problem, non-batman-adv components weren't aware of MTU changes
and thus couldn't perform their own tasks correctly.
Set the next pointer in filename_trans_read_helper() before attaching
the new node under construction to the list, otherwise garbage would be
dereferenced on subsequent failure during cleanup in the out goto label.
Cc: <stable@vger.kernel.org> Fixes: 430059024389 ("selinux: implement new format of filename transitions") Signed-off-by: Christian Göttsche <cgzones@googlemail.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have some reports of linux NFS clients that cannot satisfy a linux knfsd
server that always sets SEQ4_STATUS_RECALLABLE_STATE_REVOKED even though
those clients repeatedly walk all their known state using TEST_STATEID and
receive NFS4_OK for all.
Its possible for revoke_delegation() to set NFS4_REVOKED_DELEG_STID, then
nfsd4_free_stateid() finds the delegation and returns NFS4_OK to
FREE_STATEID. Afterward, revoke_delegation() moves the same delegation to
cl_revoked. This would produce the observed client/server effect.
Fix this by ensuring that the setting of sc_type to NFS4_REVOKED_DELEG_STID
and move to cl_revoked happens within the same cl_lock. This will allow
nfsd4_free_stateid() to properly remove the delegation from cl_revoked.
When page_handle_poison() fails to handle the hugepage or free page in
retry path, soft_offline_page() will return 0 while -EBUSY is expected in
this case.
Consequently the user will think soft_offline_page succeeds while it in
fact failed. So the user will not try again later in this case.
Link: https://lkml.kernel.org/r/20230627112808.1275241-1-linmiaohe@huawei.com Fixes: b94e02822deb ("mm,hwpoison: try to narrow window race for free pages") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Acked-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
flush_cache_vmap() must be called after new vmalloc mappings are installed
in the page table in order to allow architectures to make sure the new
mapping is visible.
It could lead to a panic since on some architectures (like powerpc),
the page table walker could see the wrong pte value and trigger a
spurious page fault that can not be resolved (see commit f1cb8f9beba8
("powerpc/64s/radix: avoid ptesync after set_pte and
ptep_set_access_flags")).
But actually the patch is aiming at riscv: the riscv specification
allows the caching of invalid entries in the TLB, and since we recently
removed the vmalloc page fault handling, we now need to emit a tlb
shootdown whenever a new vmalloc mapping is emitted
(https://lore.kernel.org/linux-riscv/20230725132246.817726-1-alexghiti@rivosinc.com/).
That's a temporary solution, there are ways to avoid that :)
In contrast to most other GUP code, GUP-fast common page table walking
code like gup_pte_range() also handles hugetlb pages. But in contrast to
other hugetlb page table walking code, it does not look at the hugetlb PTE
abstraction whereby we have only a single logical hugetlb PTE per hugetlb
page, even when using multiple cont-PTEs underneath -- which is for
example what huge_ptep_get() abstracts.
So when we have a hugetlb page that is mapped via cont-PTEs, GUP-fast
might stumble over a PTE that does not map the head page of a hugetlb page
-- not the first "head" PTE of such a cont mapping.
Logically, the whole hugetlb page is mapped (entire_mapcount == 1), but we
might end up calling gup_must_unshare() with a tail page of a hugetlb
page.
We only maintain a single PageAnonExclusive flag per hugetlb page (as
hugetlb pages cannot get partially COW-shared), stored for the head page.
That flag is clear for all tail pages.
So when gup_must_unshare() ends up calling PageAnonExclusive() with a tail
page of a hugetlb page:
Always detects "not exclusive" for passed tail pages and refuses to PIN
the tail pages R/O, as gup_must_unshare() == true. GUP-fast will fallback
to ordinary GUP. As ordinary GUP properly considers the logical hugetlb
PTE abstraction in hugetlb_follow_page_mask(), pinning the page will
succeed when looking at the PageAnonExclusive on the head page only.
So the only real effect of this is that with cont-PTE hugetlb pages, we'll
always fallback from GUP-fast to ordinary GUP when not working on the head
page, which ends up checking the head page and do the right thing.
Consequently, the cow selftests pass with cont-PTE hugetlb pages as well
without CONFIG_DEBUG_VM_PGFLAGS.
Note that this only applies to anon hugetlb pages that are mapped using
cont-PTEs: for example 64k hugetlb pages on a 4k arm64 kernel.
... and only when R/O-pinning (FOLL_PIN) such pages that are mapped into
the page table R/O using GUP-fast.
On production kernels (and even most debug kernels, that don't set
CONFIG_DEBUG_VM_PGFLAGS) this patch should theoretically not be required
to be backported. But of course, it does not hurt.
Link: https://lkml.kernel.org/r/20230805101256.87306-1-david@redhat.com Fixes: a7f226604170 ("mm/gup: trigger FAULT_FLAG_UNSHARE when R/O-pinning a possibly shared anonymous page") Signed-off-by: David Hildenbrand <david@redhat.com> Reported-by: Ryan Roberts <ryan.roberts@arm.com> Reviewed-by: Ryan Roberts <ryan.roberts@arm.com> Tested-by: Ryan Roberts <ryan.roberts@arm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Jason Gunthorpe <jgg@nvidia.com> Cc: Peter Xu <peterx@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like a few other drivers, YMFPCI driver needs to clean up with
snd_card_free() call at an error path of the probe; otherwise the
other devres resources are released before the card and it results in
the UAF.
This patch uses the helper for handling the probe error gracefully.
smaps_pte_hole_lookup() is calling shmem_partial_swap_usage() with page
table lock held: but shmem_partial_swap_usage() does cond_resched_rcu() if
need_resched(): "BUG: sleeping function called from invalid context".
Since shmem_partial_swap_usage() is designed to count across a range, but
smaps_pte_hole_lookup() only calls it for a single page slot, just break
out of the loop on the last or only page, before checking need_resched().
Link: https://lkml.kernel.org/r/6fe3b3ec-abdf-332f-5c23-6a3b3a3b11a9@google.com Fixes: 230100321518 ("mm/smaps: simplify shmem handling of pte holes") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> [5.16+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code calling ima_free_kexec_buffer runs long after the memblock
allocator has already been torn down, potentially resulting in a use
after free in memblock_isolate_range.
With KASAN or KFENCE, this use after free will result in a BUG
from the idle task, and a subsequent kernel panic.
Switch ima_free_kexec_buffer over to memblock_free_late to avoid
that issue.
Fixes: fee3ff99bc67 ("powerpc: Move arch independent ima kexec functions to drivers/of/kexec.c") Cc: stable@kernel.org Signed-off-by: Rik van Riel <riel@surriel.com> Suggested-by: Mike Rappoport <rppt@kernel.org> Link: https://lore.kernel.org/r/20230817135759.0888e5ef@imladris.surriel.com Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log