In unprivileged Xen guests event handling can cause a deadlock with
Xen console handling. The evtchn_rwlock and the hvc_lock are taken in
opposite sequence in __hvc_poll() and in Xen console IRQ handling.
Normally this is no problem, as the evtchn_rwlock is taken as a reader
in both paths, but as soon as an event channel is being closed, the
lock will be taken as a writer, which will cause read_lock() to block:
read_lock(evtchn_rwlock)
spin_lock(hvc_lock)
write_lock(evtchn_rwlock)
[blocks]
spin_lock(hvc_lock)
[blocks]
read_lock(evtchn_rwlock)
[blocks due to writer waiting,
and not in_interrupt()]
This issue can be avoided by replacing evtchn_rwlock with RCU in
xen_free_irq(). Note that RCU is used only to delay freeing of the
irq_info memory. There is no RCU based dereferencing or replacement of
pointers involved.
In order to avoid potential races between removing the irq_info
reference and handling of interrupts, set the irq_info pointer to NULL
only when freeing its memory. The IRQ itself must be freed at that
time, too, as otherwise the same IRQ number could be allocated again
before handling of the old instance would have been finished.
This is XSA-441 / CVE-2023-34324.
Fixes: 54c9de89895e ("xen/events: add a new "late EOI" evtchn framework") Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Julien Grall <jgrall@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rt6_check_neigh() uses read_lock() to protect n->nud_state reading.
This seems overkill and causes false sharing.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was noticed by Miklos that file_remove_privs might call into
notify_change(), which requires to hold an exclusive lock. The problem
exists in FUSE and btrfs. We can fix it without any additional helpers
from VFS, in case the privileges would need to be dropped, change the
lock type to be exclusive and redo the loop.
Fixes: e9adabb9712e ("btrfs: use shared lock for direct writes within EOF") CC: Miklos Szeredi <miklos@szeredi.hu> CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Bernd Schubert <bschubert@ddn.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've added a flex array to struct nlmsghdr in
commit 738136a0e375 ("netlink: split up copies in the ack construction")
to allow accessing the data easily. It leads to warnings with clang,
if user space wraps this structure into another struct and the flex
array is not at the end of the container.
When logging a new name, we don't expect to fail joining a log transaction
since we know at least one of the inodes was logged before in the current
transaction. However if we fail for some unexpected reason, we end up not
freeing the fscrypt name we previously allocated. So fix that by freeing
the name in case we failed to join a log transaction.
Fixes: ab3c5c18e8fa ("btrfs: setup qstr from dentrys using fscrypt helper") Reviewed-by: Sweet Tea Dorminy <sweettea-kernel@dorminy.me> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cited commit converted the neighbour code to use the standard RCU
variant instead of the RCU-bh variant, but the VRF code still uses
rcu_read_lock_bh() / rcu_read_unlock_bh() around the neighbour lookup
code in its IPv4 and IPv6 output paths, resulting in lockdep splats
[1][2]. Can be reproduced using [3].
Fix by switching to rcu_read_lock() / rcu_read_unlock().
ip link add name vrf-red up numtxqueues 2 type vrf table 10
ip link add name swp1 up master vrf-red type dummy
ip address add 192.0.2.1/24 dev swp1
ip address add 2001:db8:1::1/64 dev swp1
ip neigh add 192.0.2.2 lladdr 00:11:22:33:44:55 nud perm dev swp1
ip neigh add 2001:db8:1::2 lladdr 00:11:22:33:44:55 nud perm dev swp1
ip vrf exec vrf-red ping 192.0.2.2 -c 1 &> /dev/null
ip vrf exec vrf-red ping6 2001:db8:1::2 -c 1 &> /dev/null
After blamed commit, nexthop_fib6_nh_bh() and nexthop_fib6_nh()
are the same.
Delete nexthop_fib6_nh_bh(), and convert /proc/net/ipv6_route
to standard rcu to avoid this splat:
[ 5723.180080] WARNING: suspicious RCU usage
[ 5723.180083] -----------------------------
[ 5723.180084] include/net/nexthop.h:516 suspicious rcu_dereference_check() usage!
[ 5723.180086]
other info that might help us debug this:
Back in 2005, Kyle McMartin removed the 16-byte alignment for
ldcw semaphores on PA 2.0 machines (CONFIG_PA20). This broke
spinlocks on pre PA8800 processors. The main symptom was random
faults in mmap'd memory (e.g., gcc compilations, etc).
Unfortunately, the errata for this ldcw change is lost.
The issue is the 16-byte alignment required for ldcw semaphore
instructions can only be reduced to natural alignment when the
ldcw operation can be handled coherently in cache. Only PA8800
and PA8900 processors actually support doing the operation in
cache.
Aligning the spinlock dynamically adds two integer instructions
to each spinlock.
SNP retrieves the majority of CPUID information from the SNP CPUID page.
But there are times when that information needs to be supplemented by the
hypervisor, for example, obtaining the initial APIC ID of the vCPU from
leaf 1.
The current implementation uses the MSR protocol to retrieve the data from
the hypervisor, even when a GHCB exists. The problem arises when an NMI
arrives on return from the VMGEXIT. The NMI will be immediately serviced
and may generate a #VC requiring communication with the hypervisor.
Since a GHCB exists in this case, it will be used. As part of using the
GHCB, the #VC handler will write the GHCB physical address into the GHCB
MSR and the #VC will be handled.
When the NMI completes, processing resumes at the site of the VMGEXIT
which is expecting to read the GHCB MSR and find a CPUID MSR protocol
response. Since the NMI handling overwrote the GHCB MSR response, the
guest will see an invalid reply from the hypervisor and self-terminate.
Fix this problem by using the GHCB when it is available. Any NMI
received is properly handled because the GHCB contents are copied into
a backup page and restored on NMI exit, thus preserving the active GHCB
request or result.
In case immediate MPA request processing fails, the newly
created endpoint unlinks the listening endpoint and is
ready to be dropped. This special case was not handled
correctly by the code handling the later TCP socket close,
causing a NULL dereference crash in siw_cm_work_handler()
when dereferencing a NULL listener. We now also cancel
the useless MPA timeout, if immediate MPA request
processing fails.
This patch furthermore simplifies MPA processing in general:
Scheduling a useless TCP socket read in sk_data_ready() upcall
is now surpressed, if the socket is already moved out of
TCP_ESTABLISHED state.
Fixes: 6c52fdc244b5 ("rdma/siw: connection management") Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Link: https://lore.kernel.org/r/20230905145822.446263-1-bmt@zurich.ibm.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After scmd_eh_abort_handler() has called the SCSI LLD eh_abort_handler
callback, it performs one of the following actions:
* Call scsi_queue_insert().
* Call scsi_finish_command().
* Call scsi_eh_scmd_add().
Hence, SCSI abort handlers must not call scsi_done(). Otherwise all
the above actions would trigger a use-after-free. Hence remove the
scsi_done() call from srp_abort(). Keep the srp_free_req() call
before returning SUCCESS because we may not see the command again if
SUCCESS is returned.
Cc: Bob Pearson <rpearsonhpe@gmail.com> Cc: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com> Fixes: d8536670916a ("IB/srp: Avoid having aborted requests hang") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20230823205727.505681-1-bvanassche@acm.org Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since size of 'hdr' pointer and '*hdr' structure is equal on 64-bit
machines issue probably didn't cause any wrong behavior. But anyway,
fixing of typo is required.
Fixes: da0f60df7bd5 ("RDMA/uverbs: Prohibit write() calls with too small buffers") Co-developed-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com> Signed-off-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com> Signed-off-by: Konstantin Meskhidze <konstantin.meskhidze@huawei.com> Link: https://lore.kernel.org/r/20230905103258.1738246-1-konstantin.meskhidze@huawei.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following compilation error is false alarm as RDMA devices don't
have such large amount of ports to actually cause to format truncation.
drivers/infiniband/core/cma_configfs.c: In function ‘make_cma_ports’:
drivers/infiniband/core/cma_configfs.c:223:57: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
223 | snprintf(port_str, sizeof(port_str), "%u", i + 1);
| ^
drivers/infiniband/core/cma_configfs.c:223:17: note: ‘snprintf’ output between 2 and 11 bytes into a destination of size 10
223 | snprintf(port_str, sizeof(port_str), "%u", i + 1);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[5]: *** [scripts/Makefile.build:243: drivers/infiniband/core/cma_configfs.o] Error 1
Initialize the structure to 0 so that it's fields won't have random
values. For example fields like rec.traffic_class (as well as
rec.flow_label and rec.sl) is used to generate the user AH through:
cma_iboe_join_multicast
cma_make_mc_event
ib_init_ah_from_mcmember
And a random traffic_class causes a random IP DSCP in RoCEv2.
Fixes: b5de0c60cc30 ("RDMA/cma: Fix use after free race in roce multicast join") Signed-off-by: Mark Zhang <markzhang@nvidia.com> Link: https://lore.kernel.org/r/20230927090511.603595-1-markzhang@nvidia.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pinctrl_gpio_set_config() expects the GPIO number from the global GPIO
numberspace, not the controller-relative offset, which needs to be added
to the chip base.
In order to be sure that 'buff' is never truncated, its size should be
12, not 11.
When building with W=1, this fixes the following warnings:
drivers/infiniband/hw/mlx4/sysfs.c: In function ‘add_port_entries’:
drivers/infiniband/hw/mlx4/sysfs.c:268:34: error: ‘sprintf’ may write a terminating nul past the end of the destination [-Werror=format-overflow=]
268 | sprintf(buff, "%d", i);
| ^
drivers/infiniband/hw/mlx4/sysfs.c:268:17: note: ‘sprintf’ output between 2 and 12 bytes into a destination of size 11
268 | sprintf(buff, "%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/sysfs.c:286:34: error: ‘sprintf’ may write a terminating nul past the end of the destination [-Werror=format-overflow=]
286 | sprintf(buff, "%d", i);
| ^
drivers/infiniband/hw/mlx4/sysfs.c:286:17: note: ‘sprintf’ output between 2 and 12 bytes into a destination of size 11
286 | sprintf(buff, "%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~
Smatch complains that the error path where "action" is invalid leaks
the "ce" allocation:
drivers/of/dynamic.c:935 of_changeset_action()
warn: possible memory leak of 'ce'
Fix this by doing the validation before the allocation.
Note that there is not any actual problem with upstream kernels. All
callers of of_changeset_action() are static inlines with fixed action
values.
Fixes: 914d9d831e61 ("of: dynamic: Refactor action prints to not use "%pOF" inside devtree_lock") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/r/202309011059.EOdr4im9-lkp@intel.com/ Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/7dfaf999-30ad-491c-9615-fb1138db121c@moroto.mountain Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4dba12881f88 ("dm zoned: support arbitrary number of devices")
made the pointers to additional zoned devices to be stored in a
dynamically allocated dmz->ddev array. However, this array is not freed.
Rename dmz_put_zoned_device to dmz_put_zoned_devices and fix it to
free the dmz->ddev array when cleaning up zoned device information.
Remove NULL assignment for all dmz->ddev elements and just free the
dmz->ddev array instead.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4dba12881f88 ("dm zoned: support arbitrary number of devices") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent changes to kernel_connect() and kernel_bind() ensure that
callers are insulated from changes to the address parameter made by BPF
SOCK_ADDR hooks. This patch wraps direct calls to ops->connect() and
ops->bind() with kernel_connect() and kernel_bind() to ensure that SMB
mounts do not see their mount address overwritten in such cases.
Emerald Rapids (EMR) is the next Intel Xeon processor after Sapphire
Rapids (SPR).
EMR C-states are the same as SPR C-states, and we expect that EMR
C-state characteristics (latency and target residency) will be the
same as in SPR. Therefore, add EMR support by using SPR C-states table.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
service, which allows to wakup device when the system is in S5 (Soft-Off
state). This OOB service can be enabled/disabled from BIOS settings. When
enabled, the ISH device gets PME wake capability. To enable PME wakeup,
driver also needs to enable ACPI GPE bit.
On resume, BIOS will clear the wakeup bit. So driver need to re-enable it
in resume function to keep the next wakeup capability. But this BIOS
clearing of wakeup bit doesn't decrement internal OS GPE reference count,
so this reenabling on every resume will cause reference count to overflow.
So first disable and reenable ACPI GPE bit using acpi_disable_gpe().
syzbot caught another data-race in netlink when
setting sk->sk_err.
Annotate all of them for good measure.
BUG: KCSAN: data-race in netlink_recvmsg / netlink_recvmsg
write to 0xffff8881613bb220 of 4 bytes by task 28147 on cpu 0:
netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994
sock_recvmsg_nosec net/socket.c:1027 [inline]
sock_recvmsg net/socket.c:1049 [inline]
__sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229
__do_sys_recvfrom net/socket.c:2247 [inline]
__se_sys_recvfrom net/socket.c:2243 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2243
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
write to 0xffff8881613bb220 of 4 bytes by task 28146 on cpu 1:
netlink_recvmsg+0x448/0x780 net/netlink/af_netlink.c:1994
sock_recvmsg_nosec net/socket.c:1027 [inline]
sock_recvmsg net/socket.c:1049 [inline]
__sys_recvfrom+0x1f4/0x2e0 net/socket.c:2229
__do_sys_recvfrom net/socket.c:2247 [inline]
__se_sys_recvfrom net/socket.c:2243 [inline]
__x64_sys_recvfrom+0x78/0x90 net/socket.c:2243
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x00000000 -> 0x00000016
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 28146 Comm: syz-executor.0 Not tainted 6.6.0-rc3-syzkaller-00055-g9ed22ae6be81 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/06/2023
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20231003183455.3410550-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clean up the use of unsafe_memcpy() by adding a flexible array
at the end of netlink message header and splitting up the header
and data copies.
Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: d0f95894fda7 ("netlink: annotate data-races around sk->sk_err") Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, when hb_interval is changed by users, it won't take effect
until the next expiry of hb timer. As the default value is 30s, users
have to wait up to 30s to wait its hb_interval update to work.
This becomes pretty bad in containers where a much smaller value is
usually set on hb_interval. This patch improves it by resetting the
hb timer immediately once the value of hb_interval is updated by users.
Note that we don't address the already existing 'problem' when sending
a heartbeat 'on demand' if one hb has just been sent(from the timer)
mentioned in:
During the 4-way handshake, the transport's state is set to ACTIVE in
sctp_process_init() when processing INIT_ACK chunk on client or
COOKIE_ECHO chunk on server.
when processing COOKIE_ECHO on 192.168.1.2, as it's in COOKIE_WAIT state,
sctp_sf_do_dupcook_b() is called by sctp_sf_do_5_2_4_dupcook() where it
creates a new association and sets its transport to ACTIVE then updates
to the old association in sctp_assoc_update().
However, in sctp_assoc_update(), it will skip the transport update if it
finds a transport with the same ipaddr already existing in the old asoc,
and this causes the old asoc's transport state not to move to ACTIVE
after the handshake.
This means if DATA retransmission happens at this moment, it won't be able
to enter PF state because of the check 'transport->state == SCTP_ACTIVE'
in sctp_do_8_2_transport_strike().
This patch fixes it by updating the transport in sctp_assoc_update() with
sctp_assoc_add_peer() where it updates the transport state if there is
already a transport with the same ipaddr exists in the old asoc.
This commit fixes poor delayed ACK behavior that can cause poor TCP
latency in a particular boundary condition: when an application makes
a TCP socket write that is an exact multiple of the MSS size.
The problem is that there is painful boundary discontinuity in the
current delayed ACK behavior. With the current delayed ACK behavior,
we have:
(1) If an app reads data when > 1*MSS is unacknowledged, then
tcp_cleanup_rbuf() ACKs immediately because of:
(2) If an app reads all received data, and the packets were < 1*MSS,
and either (a) the app is not ping-pong or (b) we received two
packets < 1*MSS, then tcp_cleanup_rbuf() ACKs immediately beecause
of:
(3) *However*: if an app reads exactly 1*MSS of data,
tcp_cleanup_rbuf() does not send an immediate ACK. This is true
even if the app is not ping-pong and the 1*MSS of data had the PSH
bit set, suggesting the sending application completed an
application write.
Thus if the app is not ping-pong, we have this painful case where
>1*MSS gets an immediate ACK, and <1*MSS gets an immediate ACK, but a
write whose last skb is an exact multiple of 1*MSS can get a 40ms
delayed ACK. This means that any app that transfers data in one
direction and takes care to align write size or packet size with MSS
can suffer this problem. With receive zero copy making 4KB MSS values
more common, it is becoming more common to have application writes
naturally align with MSS, and more applications are likely to
encounter this delayed ACK problem.
The fix in this commit is to refine the delayed ACK heuristics with a
simple check: immediately ACK a received 1*MSS skb with PSH bit set if
the app reads all data. Why? If an skb has a len of exactly 1*MSS and
has the PSH bit set then it is likely the end of an application
write. So more data may not be arriving soon, and yet the data sender
may be waiting for an ACK if cwnd-bound or using TX zero copy. Thus we
set ICSK_ACK_PUSHED in this case so that tcp_cleanup_rbuf() will send
an ACK immediately if the app reads all of the data and is not
ping-pong. Note that this logic is also executed for the case where
len > MSS, but in that case this logic does not matter (and does not
hurt) because tcp_cleanup_rbuf() will always ACK immediately if the
app reads data and there is more than an MSS of unACKed data.
This commit fixes quick-ack counting so that it only considers that a
quick-ack has been provided if we are sending an ACK that newly
acknowledges data.
The code was erroneously using the number of data segments in outgoing
skbs when deciding how many quick-ack credits to remove. This logic
does not make sense, and could cause poor performance in
request-response workloads, like RPC traffic, where requests or
responses can be multi-segment skbs.
When a TCP connection decides to send N quick-acks, that is to
accelerate the cwnd growth of the congestion control module
controlling the remote endpoint of the TCP connection. That quick-ack
decision is purely about the incoming data and outgoing ACKs. It has
nothing to do with the outgoing data or the size of outgoing data.
And in particular, an ACK only serves the intended purpose of allowing
the remote congestion control to grow the congestion window quickly if
the ACK is ACKing or SACKing new data.
The fix is simple: only count packets as serving the goal of the
quickack mechanism if they are ACKing/SACKing new data. We can tell
whether this is the case by checking inet_csk_ack_scheduled(), since
we schedule an ACK exactly when we are ACKing/SACKing new data.
Fixes: fc6415bcb0f5 ("[TCP]: Fix quick-ack decrementing with TSO.") Signed-off-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20231001151239.1866845-1-ncardwell.sw@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It seems that tipc_crypto_key_revoke() could be be invoked by
wokequeue tipc_crypto_work_rx() under process context and
timer/rx callback under softirq context, thus the lock acquisition
on &tx->lock seems better use spin_lock_bh() to prevent possible
deadlock.
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.
This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.
This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.
Fixes: 6528e02cc9ff ("net: ethernet: stmmac: add adaptation for stm32mp157c.") Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20230927175749.1419774-1-ben.wolsieffer@hefring.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to a small omission, the offload_failed flag is missing from ipv4
fibmatch results. Make sure it is set correctly.
The issue can be witnessed using the following commands:
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add dummy1 up type dummy
ip route add 192.0.2.0/24 dev dummy1
echo 1 > /sys/kernel/debug/netdevsim/netdevsim1/fib/fail_route_offload
ip route add 198.51.100.0/24 dev dummy1
ip route
# 192.168.15.0/24 has rt_trap
# 198.51.100.0/24 has rt_offload_failed
ip route get 192.168.15.1 fibmatch
# Result has rt_trap
ip route get 198.51.100.1 fibmatch
# Result differs from the route shown by `ip route`, it is missing
# rt_offload_failed
ip link del dev dummy1
echo 1 > /sys/bus/netdevsim/del_device
Fixes: 36c5100e859d ("IPv4: Add "offload failed" indication to routes") Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230926182730.231208-1-bpoirier@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
nft_rbtree_gc_elem() walks back and removes the end interval element that
comes before the expired element.
There is a small chance that we've cached this element as 'rbe_ge'.
If this happens, we hold and test a pointer that has been queued for
freeing.
It also causes spurious insertion failures:
$ cat test-testcases-sets-0044interval_overlap_0.1/testout.log
Error: Could not process rule: File exists
add element t s { 0 - 2 }
^^^^^^
Failed to insert 0 - 2 given:
table ip t {
set s {
type inet_service
flags interval,timeout
timeout 2s
gc-interval 2s
}
}
The set (rbtree) is empty. The 'failure' doesn't happen on next attempt.
Reason is that when we try to insert, the tree may hold an expired
element that collides with the range we're adding.
While we do evict/erase this element, we can trip over this check:
if (rbe_ge && nft_rbtree_interval_end(rbe_ge) && nft_rbtree_interval_end(new))
return -ENOTEMPTY;
rbe_ge was erased by the synchronous gc, we should not have done this
check. Next attempt won't find it, so retry results in successful
insertion.
Restart in-kernel to avoid such spurious errors.
Such restart are rare, unless userspace intentionally adds very large
numbers of elements with very short timeouts while setting a huge
gc interval.
Even in this case, this cannot loop forever, on each retry an existing
element has been removed.
As the caller is holding the transaction mutex, its impossible
for a second entity to add more expiring elements to the tree.
After this it also becomes feasible to remove the async gc worker
and perform all garbage collection from the commit path.
Fixes: c9e6978e2725 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adding/updating an object, the transaction handler emits suitable
audit log entries already, the one in nft_obj_notify() is redundant. To
fix that (and retain the audit logging from objects' 'update' callback),
Introduce an "audit log free" variant for internal use.
Fixes: c520292f29b8 ("audit: log nftables configuration change events once per table") Signed-off-by: Phil Sutter <phil@nwl.cc> Reviewed-by: Richard Guy Briggs <rgb@redhat.com> Acked-by: Paul Moore <paul@paul-moore.com> (Audit) Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add tests for sets and elements and deletion of all kinds. Also
reorder rule reset tests: By moving the bulk rule add command up, the
two 'reset rules' tests become identical.
While at it, fix for a failing bulk rule add test's error status getting
lost due to its use in a pipe. Avoid this by using a temporary file.
Headings in diff output for failing tests contain no useful data, strip
them.
In SCTP_CID_INIT processing:
- clear ct->proto.sctp.init[!dir] if ct->proto.sctp.init[dir] &&
ct->proto.sctp.init[!dir]. (Scenario E)
- set ct->proto.sctp.init[dir].
In SCTP_CID_INIT_ACK processing:
- drop it if !ct->proto.sctp.init[!dir] && ct->proto.sctp.vtag[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario B, Scenario C)
- drop it if ct->proto.sctp.init[dir] && ct->proto.sctp.init[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario A)
In SCTP_CID_COOKIE_ACK processing:
- clear ct->proto.sctp.init[dir] and ct->proto.sctp.init[!dir].
(Scenario D)
Also, it's important to allow the ct state to move forward with cookie_echo
and cookie_ack from the opposite dir for the collision scenarios.
There are also other Scenarios where it should allow the packet through,
addressed by the processing above:
Scenario C: new CT is created by INIT_ACK.
Scenario D: start INIT on the existing ESTABLISHED ct.
Scenario E: start INIT after the old collision on the existing ESTABLISHED
ct.
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
(both side are stopped, then start new connection again in hours)
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 242308742]
In some OVS environments the TCP pseudo header checksum may need to be
recomputed. Currently this is only done when the interface instance is
configured for "Trunk Mode". We found the issue also occurs in some
Kubernetes environments, these environments do not use "Trunk Mode",
therefor the condition is removed.
Performance tests with this change show only a fractional decrease in
throughput (< 0.2%).
Fixes: 7525de2516fb ("ibmveth: Set CHECKSUM_PARTIAL if NULL TCP CSUM.") Signed-off-by: David Wilder <dwilder@us.ibm.com> Reviewed-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This accidentally returns success, but it should return a negative error
code.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This issue is caused because usbnet_read_cmd() reads less bytes than requested
(zero byte in the reproducer). In this case, 'buf' is not properly filled.
This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads
less bytes than requested.
Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver") Reported-and-tested-by: syzbot+6966546b78d050bb0b5d@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=6966546b78d050bb0b5d Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230923173549.3284502-1-syoshida@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b0e214d21203 ("netfilter: keep conntrack reference until
IPsecv6 policy checks are done") is a direct copy of the old
commit b59c270104f0 ("[NETFILTER]: Keep conntrack reference until
IPsec policy checks are done") but for IPv6. However, it also
copies a bug that this old commit had. That is: when the third
packet of 3WHS connection establishment contains payload, it is
added into socket receive queue without the XFRM check and the
drop of connection tracking context.
That leads to nf_conntrack module being impossible to unload as
it waits for all the conntrack references to be dropped while
the packet release is deferred in per-cpu cache indefinitely, if
not consumed by the application.
The issue for IPv4 was fixed in commit 6f0012e35160 ("tcp: add a
missing nf_reset_ct() in 3WHS handling") by adding a missing XFRM
check and correctly dropping the conntrack context. However, the
issue was introduced to IPv6 code afterwards. Fixing it the
same way for IPv6 now.
Since commit 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset") Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When device_add() fails, ptp_ocp_dev_release() will be called
after put_device(). Therefore, it seems that the
ptp_ocp_dev_release() before put_device() is redundant.
Fixes: 773bda964921 ("ptp: ocp: Expose various resources on the timecard.") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Vadim Feodrenko <vadim.fedorenko@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Including the transhdrlen in length is a problem when the packet is
partially filled (e.g. something like send(MSG_MORE) happened previously)
when appending to an IPv4 or IPv6 packet as we don't want to repeat the
transport header or account for it twice. This can happen under some
circumstances, such as splicing into an L2TP socket.
The symptom observed is a warning in __ip6_append_data():
WARNING: CPU: 1 PID: 5042 at net/ipv6/ip6_output.c:1800 __ip6_append_data.isra.0+0x1be8/0x47f0 net/ipv6/ip6_output.c:1800
that occurs when MSG_SPLICE_PAGES is used to append more data to an already
partially occupied skbuff. The warning occurs when 'copy' is larger than
the amount of data in the message iterator. This is because the requested
length includes the transport header length when it shouldn't. This can be
triggered by, for example:
Fix this by only adding transhdrlen into the length if the write queue is
empty in l2tp_ip6_sendmsg(), analogously to how UDP does things.
l2tp_ip_sendmsg() looks like it won't suffer from this problem as it builds
the UDP packet itself.
Fixes: a32e0eec7042 ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6") Reported-by: syzbot+62cbf263225ae13ff153@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/0000000000001c12b30605378ce8@google.com/ Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Dumazet <edumazet@google.com>
cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: David Ahern <dsahern@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: netdev@vger.kernel.org
cc: bpf@vger.kernel.org
cc: syzkaller-bugs@googlegroups.com Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
n->output field can be read locklessly, while a writer
might change the pointer concurrently.
Add missing annotations to prevent load-store tearing.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before adding another one in the following patch,
add annotations to readers and writers.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 5baa0433a15e ("neighbour: fix data-races around n->output") Signed-off-by: Sasha Levin <sashal@kernel.org>
The bpf_fib_lookup() also looks up the neigh table.
This was done before bpf_redirect_neigh() was added.
In the use case that does not manage the neigh table
and requires bpf_fib_lookup() to lookup a fib to
decide if it needs to redirect or not, the bpf prog can
depend only on using bpf_redirect_neigh() to lookup the
neigh. It also keeps the neigh entries fresh and connected.
This patch adds a bpf_fib_lookup flag, SKIP_NEIGH, to avoid
the double neigh lookup when the bpf prog always call
bpf_redirect_neigh() to do the neigh lookup. The params->smac
output is skipped together when SKIP_NEIGH is set because
bpf_redirect_neigh() will figure out the smac also.
While looking at a related syzbot report involving neigh_periodic_work(),
I found that I forgot to add an annotation when deleting an
RCU protected item from a list.
Readers use rcu_deference(*np), we need to use either
rcu_assign_pointer() or WRITE_ONCE() on writer side
to prevent store tearing.
I use rcu_assign_pointer() to have lockdep support,
this was the choice made in neigh_flush_dev().
Fixes: 767e97e1e0db ("neigh: RCU conversion of struct neighbour") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Without this 'else' statement, an "usb" name goes into two handlers:
the first/previous 'if' statement _AND_ the for-loop over 'devtable',
but the latter is useless as it has no 'usb' device_id entry anyway.
Tested with allmodconfig before/after patch; no changes to *.mod.c:
git checkout v6.6-rc3
make -j$(nproc) allmodconfig
make -j$(nproc) olddefconfig
make -j$(nproc)
find . -name '*.mod.c' | cpio -pd /tmp/before
# apply patch
make -j$(nproc)
find . -name '*.mod.c' | cpio -pd /tmp/after
diff -r /tmp/before/ /tmp/after/
# no difference
Fixes: acbef7b76629 ("modpost: fix module autoloading for OF devices with generic compatible property") Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With a SOCKMAP/SOCKHASH map and an sk_msg program user can steer messages
sent from one TCP socket (s1) to actually egress from another TCP
socket (s2):
There is a hard-coded assumption in the call-chain, that the egress
socket (s2) is a TCP socket.
However in commit 122e6c79efe1 ("sock_map: Update sock type checks for
UDP") we have enabled redirects to non-TCP sockets. This was done for the
sake of BPF sk_skb programs. There was no indention to support sk_msg
send-to-egress use case.
As a result, attempts to send-to-egress through a non-TCP socket lead to a
crash due to invalid downcast from sock to tcp_sock:
Reject selecting a non-TCP sockets as redirect target from a BPF sk_msg
program to prevent the crash. When attempted, user will receive an EACCES
error from send/sendto/sendmsg() syscall.
Fixes: 122e6c79efe1 ("sock_map: Update sock type checks for UDP") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20230920102055.42662-1-jakub@cloudflare.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When data is peek'd off the receive queue we shouldn't considered it
copied from tcp_sock side. When we increment copied_seq this will confuse
tcp_data_ready() because copied_seq can be arbitrarily increased. From
application side it results in poll() operations not waking up when
expected.
Notice tcp stack without BPF recvmsg programs also does not increment
copied_seq.
We broke this when we moved copied_seq into recvmsg to only update when
actual copy was happening. But, it wasn't working correctly either before
because the tcp_data_ready() tried to use the copied_seq value to see
if data was read by user yet. See fixes tags.
Fixes: e5c6de5fa0258 ("bpf, sockmap: Incorrectly handling copied_seq") Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230926035300.135096-3-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Before fix e5c6de5fa0258 tcp_read_skb() would increment the tp->copied-seq
value. This (as described in the commit) would cause an error for apps
because once that is incremented the application might believe there is no
data to be read. Then some apps would stall or abort believing no data is
available.
However, the fix is incomplete because it introduces another issue in
the skb dequeue. The loop does tcp_recv_skb() in a while loop to consume
as many skbs as possible. The problem is the call is ...
tcp_recv_skb(sk, seq, &offset)
... where 'seq' is:
u32 seq = tp->copied_seq;
Now we can hit a case where we've yet incremented copied_seq from BPF side,
but then tcp_recv_skb() fails this test ...
if (offset < skb->len || (TCP_SKB_CB(skb)->tcp_flags & TCPHDR_FIN))
... so that instead of returning the skb we call tcp_eat_recv_skb() which
frees the skb. This is because the routine believes the SKB has been collapsed
per comment:
/* This looks weird, but this can happen if TCP collapsing
* splitted a fat GRO packet, while we released socket lock
* in skb_splice_bits()
*/
This can't happen here we've unlinked the full SKB and orphaned it. Anyways
it would confuse any BPF programs if the data were suddenly moved underneath
it.
To fix this situation do simpler operation and just skb_peek() the data
of the queue followed by the unlink. It shouldn't need to check this
condition and tcp_read_skb() reads entire skbs so there is no need to
handle the 'offset!=0' case as we would see in tcp_read_sock().
Fixes: e5c6de5fa0258 ("bpf, sockmap: Incorrectly handling copied_seq") Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230926035300.135096-2-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the NFS4CLNT_RUN_MANAGER flag got set just before we cleared
NFS4CLNT_MANAGER_RUNNING, then we might have won the race against
nfs4_schedule_state_manager(), and are responsible for handling the
recovery situation.
Fixes: aeabb3c96186 ("NFSv4: Fix a NFSv4 state manager deadlock") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Changing the direct dependencies of IMA_BLACKLIST_KEYRING and
IMA_LOAD_X509 caused them to no longer depend on IMA, but a
a configuration without IMA results in link failures:
arm-linux-gnueabi-ld: security/integrity/iint.o: in function `integrity_load_keys':
iint.c:(.init.text+0xd8): undefined reference to `ima_load_x509'
aarch64-linux-ld: security/integrity/digsig_asymmetric.o: in function `asymmetric_verify':
digsig_asymmetric.c:(.text+0x104): undefined reference to `ima_blacklist_keyring'
Adding explicit dependencies on IMA would fix this, but a more reliable
way to do this is to enclose the entire Kconfig file in an 'if IMA' block.
This also allows removing the existing direct dependencies.
The following call trace shows a deadlock issue due to recursive locking of
mutex "device_mutex". First lock acquire is in target_for_each_device() and
second in target_free_device().
The removal of IMA_TRUSTED_KEYRING made IMA_LOAD_X509
and IMA_BLACKLIST_KEYRING unavailable because the latter
two depend on the former. Since IMA_TRUSTED_KEYRING was
deprecated in favor of INTEGRITY_TRUSTED_KEYRING use it
as a dependency for the two Kconfigs affected by the
deprecation.
When fixing a memory leak in commit d3c731564e09 ("regulator: plug
of_node leak in regulator_register()'s error path") it moved the
device_initialize() call earlier, but did not move the `dev->class`
initialization. The bug was spotted and fixed by reverting part of
the commit (in commit 5f4b204b6b81 "regulator: core: fix kobject
release warning and memory leak in regulator_register()") but
introducing a different bug: now early error paths use `kfree(dev)`
instead of `put_device()` for an already initialized `struct device`.
Move the missing assignments to just after `device_initialize()`.
In mt8192/mt8186, there is only one MM IOMMU that supports 16GB iova
space, which is shared by display, vcodec and camera. These two SoC use
one pgtable and have not the flag SHARE_PGTABLE, we should also keep
share pgtable for this case.
In mtk_iommu_domain_finalise, MM IOMMU always share pgtable, thus remove
the flag SHARE_PGTABLE checking. Infra IOMMU always uses independent
pgtable.
Fixes: cf69ef46dbd9 ("iommu/mediatek: Fix two IOMMU share pagetable issue") Reported-by: Laura Nao <laura.nao@collabora.com> Closes: https://lore.kernel.org/linux-iommu/20230818154156.314742-1-laura.nao@collabora.com/ Signed-off-by: Yong Wu <yong.wu@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Tested-by: Laura Nao <laura.nao@collabora.com> Link: https://lore.kernel.org/r/20230819081443.8333-1-yong.wu@mediatek.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Zen 4 systems running buggy microcode can hit a WARN_ON() in the PMI
handler, as shown below, several times while perf runs. A simple
`perf top` run is enough to render the system unusable:
WARNING: CPU: 18 PID: 20608 at arch/x86/events/amd/core.c:944 amd_pmu_v2_handle_irq+0x1be/0x2b0
This happens because the Performance Counter Global Status Register
(PerfCntGlobalStatus) has one or more bits set which are considered
reserved according to the "AMD64 Architecture Programmer’s Manual,
Volume 2: System Programming, 24593":
To make this less intrusive, warn just once if any reserved bit is set
and prompt the user to update the microcode. Also sanitize the value to
what the code is handling, so that the overflow events continue to be
handled for the number of counters that are known to be sane.
Going forward, the following microcode patch levels are recommended
for Zen 4 processors in order to avoid such issues with reserved bits:
Commit f2eb058afc57 ("linux-firmware: Update AMD cpu microcode") from
the linux-firmware tree has binaries that meet the minimum required
patch levels.
[ sandipan: - add message to prompt users to update microcode
- rework commit message and call out required microcode levels ]
When ieee80211_key_link() is called by ieee80211_gtk_rekey_add()
but returns 0 due to KRACK protection (identical key reinstall),
ieee80211_gtk_rekey_add() will still return a pointer into the
key, in a potential use-after-free. This normally doesn't happen
since it's only called by iwlwifi in case of WoWLAN rekey offload
which has its own KRACK protection, but still better to fix, do
that by returning an error code and converting that to success on
the cfg80211 boundary only, leaving the error for bad callers of
ieee80211_gtk_rekey_add().
Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Fixes: fdf7cb4185b6 ("mac80211: accept key reinstall without changing anything") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When regcache_rbtree_write() creates a new rbtree_node it was passing the
wrong bit number to regcache_rbtree_set_register(). The bit number is the
offset __in number of registers__, but in the case of creating a new block
regcache_rbtree_write() was not dividing by the address stride to get the
number of registers.
Fix this by dividing by map->reg_stride.
Compare with regcache_rbtree_read() where the bit is checked.
This bug meant that the wrong register was marked as present. The register
that was written to the cache could not be read from the cache because it
was not marked as cached. But a nearby register could be marked as having
a cached value even if it was never written to the cache.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 3f4ff561bc88 ("regmap: rbtree: Make cache_present bitmap per node") Link: https://lore.kernel.org/r/20230922153711.28103-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Kernels older than v5.19 do not support PerfMonV2 and the PMI handler
does not clear the overflow bits of the PerfCntrGlobalStatus register.
Because of this, loading a recent kernel using kexec from an older
kernel can result in inconsistent register states on Zen 4 systems.
The PMI handler of the new kernel gets confused and shows a warning when
an overflow occurs because some of the overflow bits are set even if the
corresponding counters are inactive. These are remnants from overflows
that were handled by the older kernel.
During CPU hotplug, the PerfCntrGlobalCtl and PerfCntrGlobalStatus
registers should always be cleared for PerfMonV2-capable processors.
However, a condition used for NB event constaints applicable only to
older processors currently prevents this from happening. Move the reset
sequence to an appropriate place and also clear the LBR Freeze bit.
On MT76x0, LNA gain should be applied for both external and internal LNA.
On MT76x2, LNA gain should be treated as 0 for external LNA.
Move the LNA type based logic to mt76x2 in order to fix mt76x0.
Fixes: 2daa67588f34 ("mt76x0: unify lna_gain parsing") Reported-by: Shiji Yang <yangshiji66@outlook.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230919194747.31647-1-nbd@nbd.name Signed-off-by: Sasha Levin <sashal@kernel.org>
Process the result of hdlc_open() and call uhdlc_close()
in case of an error. It is necessary to pass the error
code up the control flow, similar to a possible
error in request_irq().
Also add a hdlc_close() call to the uhdlc_close()
because the comment to hdlc_close() says it must be called
by the hardware driver when the HDLC device is being closed
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC") Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
iso_listen_cis shall only return -EADDRINUSE if the listening socket has
the destination set to BDADDR_ANY otherwise if the destination is set to
a specific address it is for broadcast which shall be ignored.
Fixes: f764a6c2c1e4 ("Bluetooth: ISO: Add broadcast support") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The buck and linear range LDO (VSRAM_*) regulators share one set of ops.
This set includes support for get/set mode. However this only makes
sense for buck regulators, not LDOs. The callbacks were not checking
whether the register offset and/or mask for mode setting was valid or
not. This ends up making the kernel report "normal" mode operation for
the LDOs.
Create a new set of ops without the get/set mode callbacks for the
linear range LDO regulators.
Fixes: f67ff1bd58f0 ("regulator: mt6358: Add support for MT6358 regulator") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Link: https://lore.kernel.org/r/20230920085336.136238-1-wenst@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some of the regulators on the MT6358/MT6366 PMICs have just one linear
voltage range. These are the bulk regulators and VSRAM_* LDOs. Currently
they are modeled with one linear range, but also have their minimum,
maximum, and step voltage described.
Convert them to the linear voltage helpers. These helpers are a bit
simpler, and we can also drop the linear range definitions. Also reflow
the touched lines now that they are shorter.
The *_SSHUB regulators are actually alternate configuration interfaces
for their non *_SSHUB counterparts. They are not separate regulator
outputs. These registers are intended for the companion processor to
use to configure the power rails while the main processor is sleeping.
They are not intended for the main operating system to use.
Since they are not real outputs they shouldn't be modeled separately.
Remove them. Luckily no device tree actually uses them.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Link: https://lore.kernel.org/r/20230609083009.2822259-5-wenst@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 7e37c851374e ("regulator: mt6358: split ops for buck and linear range LDO regulators") Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit c3f853184bed ("leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that
is always false") fixed a no-op BUG_ON. This turned out to cause a
regression, since some in-tree device-tree files already use
LED_COLOR_ID_MULTI.
Drop the BUG_ON altogether.
Fixes: c3f853184bed ("leds: Fix BUG_ON check for LED_COLOR_ID_MULTI that is always false") Reported-by: Da Xue <da@libre.computer> Closes: https://lore.kernel.org/linux-leds/ZQLelWcNjjp2xndY@duo.ucw.cz/T/ Signed-off-by: Marek Behún <kabel@kernel.org> Link: https://lore.kernel.org/r/20230918140724.18634-1-kabel@kernel.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only skip the code path trying to access the rfc1042 headers when the
buffer is too small, so the driver can still process packets without
rfc1042 headers.
Fixes: 119585281617 ("wifi: mwifiex: Fix OOB and integer underflow when rx packets") Signed-off-by: Pin-yen Lin <treapking@chromium.org> Acked-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Matthew Wang <matthewmwang@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230908104308.1546501-1-treapking@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Max Schulze reports crashes with brcmfmac. The reason seems
to be a race between userspace removing the CQM config and
the driver calling cfg80211_cqm_rssi_notify(), where if the
data is freed while cfg80211_cqm_rssi_notify() runs it will
crash since it assumes wdev->cqm_config is set. This can't
be fixed with a simple non-NULL check since there's nothing
we can do for locking easily, so use RCU instead to protect
the pointer, but that requires pulling the updates out into
an asynchronous worker so they can sleep and call back into
the driver.
Since we need to change the free anyway, also change it to
go back to the old settings if changing the settings fails.
Reported-and-tested-by: Max Schulze <max.schulze@online.de> Closes: https://lore.kernel.org/r/ac96309a-8d8d-4435-36e6-6d152eb31876@online.de Fixes: 4a4b8169501b ("cfg80211: Accept multiple RSSI thresholds for CQM") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a work abstraction at the cfg80211 level that will always
hold the wiphy_lock() for any work executed and therefore also
can be canceled safely (without waiting) while holding that.
This improves on what we do now as with the new wiphy works we
don't have to worry about locking while cancelling them safely.
Also, don't let such works run while the device is suspended,
since they'll likely need to interact with the device. Flush
them before suspend though.
This is a driver callback, and the driver should be able
to assume that it's called with the wiphy lock held. Move
the call up so that's true, it has no other effect since
the device is already unregistering and we cannot reach
this function through other paths.
Most code paths in cfg80211 already hold the wiphy lock,
mostly by virtue of being called from nl80211, so make
the auto-disconnect worker also hold it, aligning the
locking promises between different parts of cfg80211.
A few lines above, space is kzalloc()'ed for:
sizeof(struct iwl_nvm_data) +
sizeof(struct ieee80211_channel) +
sizeof(struct ieee80211_rate)
'mvm->nvm_data' is a 'struct iwl_nvm_data', so it is fine.
At the end of this structure, there is the 'channels' flex array.
Each element is of type 'struct ieee80211_channel'.
So only 1 element is allocated in this array.
When doing:
mvm->nvm_data->bands[0].channels = mvm->nvm_data->channels;
We point at the first element of the 'channels' flex array.
So this is fine.
However, when doing:
mvm->nvm_data->bands[0].bitrates =
(void *)((u8 *)mvm->nvm_data->channels + 1);
because of the "(u8 *)" cast, we add only 1 to the address of the beginning
of the flex array.
It is likely that we want point at the 'struct ieee80211_rate' allocated
just after.
Remove the spurious casting so that the pointer arithmetic works as
expected.
The iwl_fw_ini_error_dump_range structure has conflicting alignment
requirements for the inner union and the outer struct:
In file included from drivers/net/wireless/intel/iwlwifi/fw/dbg.c:9:
drivers/net/wireless/intel/iwlwifi/fw/error-dump.h:312:2: error: field within 'struct iwl_fw_ini_error_dump_range' is less aligned than 'union iwl_fw_ini_error_dump_range::(anonymous at drivers/net/wireless/intel/iwlwifi/fw/error-dump.h:312:2)' and is usually due to 'struct iwl_fw_ini_error_dump_range' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
union {
As the original intention was apparently to make the entire structure
unaligned, mark the innermost members the same way so the union
becomes packed as well.
When stressing microLZMA EROFS images with the new global compressed
deduplication feature enabled (`-Ededupe`), I found some short-lived
temporary pages weren't properly released, which could slowly cause
unexpected OOMs hours later.
Let's fix it now (LZ4 and DEFLATE don't have this issue.)
There exists mtd devices with zero erasesize, which will trigger a
divide-by-zero exception while attaching ubi device.
Fix it by refusing attaching if mtd's erasesize is 0.
Implement the workaround for ARM Cortex-A520 erratum 2966298. On an
affected Cortex-A520 core, a speculatively executed unprivileged load
might leak data from a privileged load via a cache side channel. The
issue only exists for loads within a translation regime with the same
translation (e.g. same ASID and VMID). Therefore, the issue only affects
the return to EL0.
The workaround is to execute a TLBI before returning to EL0 after all
loads of privileged data. A non-shareable TLBI to any address is
sufficient.
The workaround isn't necessary if page table isolation (KPTI) is
enabled, but for simplicity it will be. Page table isolation should
normally be disabled for Cortex-A520 as it supports the CSV3 feature
and the E0PD feature (used when KASLR is enabled).
While aligning SMU11 with SMU13 implementation an assumption was made that
`dpm_context->dpm_tables.pcie_table` was populated in dpm table initialization
like in SMU13 but it isn't.
So restore some of the original logic and instead just check for
amdgpu_device_pcie_dynamic_switching_supported() to decide whether to hardcode
values; erring on the side of performance.
Cc: stable@vger.kernel.org # 6.1+ Reported-and-tested-by: Umio Yasuno <coelacanth_dream@protonmail.com> Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/1447#note_2101382 Fixes: e701156ccc6c ("drm/amd: Align SMU11 SMU_MSG_OverridePcieParameters implementation with SMU13") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems with Navi3x dGPU will attempt to use BACO for runtime
PM but fails to resume properly. This is because on these systems
the root port goes into D3cold which is incompatible with BACO.
This happens because in this case dGPU is connected to a bridge between
root port which causes BOCO detection logic to fail. Fix the intent of
the logic by looking at root port, not the immediate upstream bridge for
_PR3.
Cc: stable@vger.kernel.org Suggested-by: Jun Ma <Jun.Ma2@amd.com> Tested-by: David Perry <David.Perry@amd.com> Fixes: b10c1c5b3a4e ("drm/amdgpu: add check for ACPI power resources") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Callers of sock_sendmsg(), and similarly kernel_sendmsg(), in kernel
space may observe their value of msg_name change in cases where BPF
sendmsg hooks rewrite the send address. This has been confirmed to break
NFS mounts running in UDP mode and has the potential to break other
systems.
This patch:
1) Creates a new function called __sock_sendmsg() with same logic as the
old sock_sendmsg() function.
2) Replaces calls to sock_sendmsg() made by __sys_sendto() and
__sys_sendmsg() with __sock_sendmsg() to avoid an unnecessary copy,
as these system calls are already protected.
3) Modifies sock_sendmsg() so that it makes a copy of msg_name if
present before passing it down the stack to insulate callers from
changes to the send address.
Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/ Fixes: 1cedee13d25a ("bpf: Hooks for sys_sendmsg") Cc: stable@vger.kernel.org Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jordan Rife <jrife@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bdf399342c5 ("net: Avoid address overwrite in kernel_connect")
ensured that kernel_connect() will not overwrite the address parameter
in cases where BPF connect hooks perform an address rewrite. This change
replaces direct calls to sock->ops->connect() in net with kernel_connect()
to make these call safe.
Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/ Fixes: d74bad4e74ee ("bpf: Hooks for sys_connect") Cc: stable@vger.kernel.org Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jordan Rife <jrife@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PARF_SLV_ADDR_SPACE_SIZE_2_3_3 is used by qcom_pcie_post_init_2_3_3().
This PCIe slave address space size register offset is 0x358 but was
incorrectly changed to 0x16c by 39171b33f652 ("PCI: qcom: Remove PCIE20_
prefix from register definitions").
This prevented access to slave address space registers like iATU, etc.,
so the IPQ8074 PCIe controller was not enumerated.
Revert back to the correct 0x358 offset and remove the unused
PARF_SLV_ADDR_SPACE_SIZE_2_3_3.
projects / linux-stable / log