If the offset equals the bv_len of the first registered bvec, then the
request does not include any of that first bvec. Skip it so that drivers
don't have to deal with a zero length bvec, which was observed to break
NVMe's PRP list creation.
Cc: stable@vger.kernel.org Fixes: bd11b3a391e3 ("io_uring: don't use iov_iter_advance() for fixed buffers") Signed-off-by: Keith Busch <kbusch@kernel.org> Link: https://lore.kernel.org/r/20231120221831.2646460-1-kbusch@meta.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm glue driver is overriding the interrupt trigger types
defined by firmware when requesting the wakeup interrupts during probe.
This can lead to a failure to map the DP/DM wakeup interrupts after a
probe deferral as the firmware defined trigger types do not match the
type used for the initial mapping:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
irq: type mismatch, failed to map hwirq-15 for interrupt-controller@b220000!
Fix this by not overriding the firmware provided trigger types when
requesting the wakeup interrupts.
The default mode, configurable by DT, shall be set before usb role switch
driver is registered. Otherwise there is a race between default mode
and mode set by usb role switch driver.
Fixes: 98ed256a4dbad ("usb: dwc3: Add support for role-switch-default-mode binding") Cc: stable <stable@kernel.org> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20231025095110.2405281-1-alexander.stein@ew.tq-group.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc2_hc_n_intr() writes back INTMASK as read but evaluates it
with intmask applied. In stress testing this causes spurious
interrupts like this:
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 7 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 0 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_update_urb_state_abn(): trimming xfer length
Applying INTMASK prevents this. The issue exists in all versions of the
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Tested-by: Ivan Ivanov <ivan.ivanov@suse.com> Tested-by: Andrea della Porta <andrea.porta@suse.com> Link: https://lore.kernel.org/r/20231115144514.15248-1-oneukum@suse.com Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hard reset queued prior to error recovery (or) received during
error recovery will make TCPM to prematurely exit error recovery
sequence. Ignore hard resets received during error recovery (or)
port reset sequence.
```
[46505.459688] state change SNK_READY -> ERROR_RECOVERY [rev3 NONE_AMS]
[46505.459706] state change ERROR_RECOVERY -> PORT_RESET [rev3 NONE_AMS]
[46505.460433] disable vbus discharge ret:0
[46505.461226] Setting usb_comm capable false
[46505.467244] Setting voltage/current limit 0 mV 0 mA
[46505.467262] polarity 0
[46505.470695] Requesting mux state 0, usb-role 0, orientation 0
[46505.475621] cc:=0
[46505.476012] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev3 NONE_AMS]
[46505.476020] Received hard reset
[46505.476024] state change PORT_RESET -> HARD_RESET_START [rev3 HARD_RESET]
```
Cc: stable@vger.kernel.org Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)") Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Acked-by: Heikki Krogeus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20231101021909.2962679-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Free the interface up, to rebind it to
qmi_wwan driver.
The proper configuration is:
Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI
L716-EU is a Fibocom module based on ZTE's V3E/V3T chipset.
Device creates multiple interfaces when connected to PC as follows:
- Network Interface: ECM or RNDIS (set by FW or AT Command)
- ttyUSB0: AT port
- ttyUSB1: Modem port
- ttyUSB2: AT2 port
- ttyUSB3: Trace port for log information
- ADB: ADB port for debugging. ("Driver=usbfs" when ADB server enabled)
Here are the outputs of lsusb and usb-devices:
$ ls /dev/ttyUSB*
/dev/ttyUSB0 /dev/ttyUSB1 /dev/ttyUSB2 /dev/ttyUSB3
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
cc: stable@vger.kernel.org Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") Signed-off-by: Pawel Laszczak <pawell@cadence.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20231108093125.224963-1-pawell@cadence.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "counter = -4294967297" means that lock count is -1 and a write lock
is being attempted. Then, we found that there is a btree with a counter
of 1 in btree_cache_freeable.
We found that this is a bug in bch_sectors_dirty_init() when locking c->root:
(1). Thread X has locked c->root(A) write.
(2). Thread Y failed to lock c->root(A), waiting for the lock(c->root A).
(3). Thread X bch_btree_set_root() changes c->root from A to B.
(4). Thread X releases the lock(c->root A).
(5). Thread Y successfully locks c->root(A).
(6). Thread Y releases the lock(c->root B).
In SHOW(), the variable 'n' is of type 'size_t.' While there is a
conditional check to verify that 'n' is not equal to zero before
executing the 'do_div' macro, concerns arise regarding potential
division by zero error in 64-bit environments.
The concern arises when 'n' is 64 bits in size, greater than zero, and
the lower 32 bits of it are zeros. In such cases, the conditional check
passes because 'n' is non-zero, but the 'do_div' macro casts 'n' to
'uint32_t,' effectively truncating it to its lower 32 bits.
Consequently, the 'n' value becomes zero.
To fix this potential division by zero error and ensure precise
division handling, this commit replaces the 'do_div' macro with
div64_u64(). div64_u64() is designed to work with 64-bit operands,
guaranteeing that division is performed correctly.
This change enhances the robustness of the code, ensuring that division
operations yield accurate results in all scenarios, eliminating the
possibility of division by zero, and improving compatibility across
different 64-bit environments.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
In btree_gc_rewrite_node(), pointer 'n' is not checked after it returns
from btree_gc_rewrite_node(). There is potential possibility that 'n' is
a non NULL ERR_PTR(), referencing such error code is not permitted in
following code. Therefore a return value checking is necessary after 'n'
is back from btree_node_alloc_replacement().
Signed-off-by: Coly Li <colyli@suse.de> Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20231120052503.6122-3-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In delay_presuspend, we set the atomic variable may_delay and then stop
the timer and flush pending bios. The intention here is to prevent the
delay target from re-arming the timer again.
However, this test is racy. Suppose that one thread goes to delay_bio,
sees that dc->may_delay is one and proceeds; now, another thread executes
delay_presuspend, it sets dc->may_delay to zero, deletes the timer and
flushes pending bios. Then, the first thread continues and adds the bio to
delayed->list despite the fact that dc->may_delay is false.
Fix this bug by changing may_delay's type from atomic_t to bool and
only access it while holding the delayed_bios_lock mutex. Note that we
don't have to grab the mutex in delay_resume because there are no bios
in flight at this point.
When a VF is being exposed form the kernel, it should be marked as "slave"
before exposing to the user-mode. The VF is not usable without netvsc
running as master. The user-mode should never see a VF without the "slave"
flag.
This commit moves the code of setting the slave flag to the time before
VF is exposed to user-mode.
Cc: stable@vger.kernel.org Fixes: 0c195567a8f6 ("netvsc: transparent VF management") Signed-off-by: Long Li <longli@microsoft.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtnl lock also needs to be held before rndis_filter_device_add()
which advertises nvsp_2_vsc_capability / sriov bit, and triggers
VF NIC offering and registering. If VF NIC finished register_netdev()
earlier it may cause name based config failure.
To fix this issue, move the call to rtnl_lock() before
rndis_filter_device_add(), so VF will be registered later than netvsc
/ synthetic NIC, and gets a name numbered (ethX) after netvsc.
Cc: stable@vger.kernel.org Fixes: e04e7a7bbd4b ("hv_netvsc: Fix a deadlock by getting rtnl lock earlier in netvsc_probe()") Reported-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dasd_profile_start() the amount of requests on the device queue are
counted. The access to the device queue is unprotected against
concurrent access. With a lot of parallel I/O, especially with alias
devices enabled, the device queue can change while dasd_profile_start()
is accessing the queue. In the worst case this leads to a kernel panic
due to incorrect pointer accesses.
Fix this by taking the device lock before accessing the queue and
counting the requests. Additionally the check for a valid profile data
pointer can be done earlier to avoid unnecessary locking in a hot path.
In order for `AT_EMPTY_PATH` to work as expected, the fact
that the user wants that behavior needs to make it to `getname_flags`
or it will return ENOENT.
The crash occurred when call wake_up(&state->wait), and then we want
to look at the value in the state. However, bch_sectors_dirty_init()
is not found in the stack of any task. Since state is allocated on
the stack, we guess that bch_sectors_dirty_init() has exited, causing
bch_dirty_init_thread() to be unable to handle kernel paging request.
In order to verify this idea, we added some printing information during
wake_up(&state->wait). We find that "wake up" is printed twice, however
we only expect the last thread to wake up once.
```dmesg
[ 994.641004] alcache: bch_dirty_init_thread() wake up
[ 994.641018] alcache: bch_dirty_init_thread() wake up
[ 994.641523] alcache: bch_sectors_dirty_init() init exit
```
There is a race. If bch_sectors_dirty_init() exits after the first wake
up, the second wake up will trigger this bug("unable to handle kernel
paging request").
We believe it is very common to wake up twice if there is no dirty, but
crash is an extremely low probability event. It's hard for us to reproduce
this issue. We attached and detached continuously for a week, with a total
of more than one million attaches and only one crash.
Putting atomic_inc(&state.started) before kthread_run() can avoid waking
up twice.
Fixes: b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be multithreaded") Signed-off-by: Mingzhe Zou <mingzhe.zou@easystack.cn> Cc: <stable@vger.kernel.org> Signed-off-by: Coly Li <colyli@suse.de> Link: https://lore.kernel.org/r/20231120052503.6122-8-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
md_end_clone_io() may overwrite error status in orig_bio->bi_status with
BLK_STS_OK. This could happen when orig_bio has BIO_CHAIN (split by
md_submit_bio => bio_split_to_limits, for example). As a result, upper
layer may miss error reported from md (or the device) and consider the
failed IO was successful.
Fix this by only update orig_bio->bi_status when current bio reports
error and orig_bio is BLK_STS_OK. This is the same behavior as
__bio_chain_endio().
Fixes: 10764815ff47 ("md: add io accounting for raid0 and raid5") Cc: stable@vger.kernel.org # v5.14+ Reported-by: Bhanu Victor DiCara <00bvd0+linux@gmail.com> Closes: https://lore.kernel.org/regressions/5727380.DvuYhMxLoT@bvd0/ Signed-off-by: Song Liu <song@kernel.org> Tested-by: Xiao Ni <xni@redhat.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At line 35 the original r[nodes].b is not always allocatored from
__bch_btree_node_alloc(), and possibly initialized as NULL pointer by
caller of btree_gc_coalesce(). Therefore the change at line 36 is not
correct.
This patch replaces the mistaken IS_ERR() by IS_ERR_OR_NULL() to avoid
potential issue.
Fixes: 028ddcac477b ("bcache: Remove unnecessary NULL point check in node allocations") Cc: <stable@vger.kernel.org> # 6.5+ Cc: Zheng Wang <zyytlz.wz@163.com> Signed-off-by: Coly Li <colyli@suse.de> Link: https://lore.kernel.org/r/20231120052503.6122-9-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a bug that when using the XEN hypervisor with bios with large
multi-page bio vectors on NVMe, the kernel deadlocks [1].
The deadlocks are caused by inability to map a large bio vector -
dma_map_sgtable always returns an error, this gets propagated to the block
layer as BLK_STS_RESOURCE and the block layer retries the request
indefinitely.
XEN uses the swiotlb framework to map discontiguous pages into contiguous
runs that are submitted to the PCIe device. The swiotlb framework has a
limitation on the length of a mapping - this needs to be announced with
the max_mapping_size method to make sure that the hardware drivers do not
create larger mappings.
Without max_mapping_size, the NVMe block driver would create large
mappings that overrun the maximum mapping size.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Link: https://lore.kernel.org/stable/ZTNH0qtmint%2FzLJZ@mail-itl/ Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Suggested-by: Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Acked-by: Stefano Stabellini <sstabellini@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/151bef41-e817-aea9-675-a35fdac4ed@redhat.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like various other ASUS ExpertBook-s, the ASUS ExpertBook B1402CVA
has an ACPI DSDT table that describes IRQ 1 as ActiveLow while
the kernel overrides it to EdgeHigh.
This prevents the keyboard from working. To fix this issue, add this laptop
to the skip_override_table so that the kernel does not override IRQ 1.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218114 Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is taken from Variscite linux kernel public git repository.
Original patch author: Nate Drude <nate.d@variscite.com>
See: https://github.com/varigit/linux-imx/blob/5.15-2.0.x-imx_var01/drivers/net/ethernet/freescale/fec_main.c#L3993-L4050
When the fec driver managed the reset, the regulator had time to
settle during the fec phy reset before calling of_mdiobus_register,
which probes the mii bus for the phy id to match the correct driver.
Now that the mdio bus controls the reset, the fec driver no longer has
any delay between enabling the regulator and calling of_mdiobus_register.
If the regulator voltage has not settled, the phy id will not be read
correctly and the generic phy driver will be used.
The following call tree explains in more detail:
fec_probe
fec_reset_phy <- no longer introduces delay after migration to mdio reset
fec_enet_mii_init
of_mdiobus_register
of_mdiobus_register_phy
fwnode_mdiobus_register_phy
get_phy_device <- mii probe for phy id to match driver happens here
...
fwnode_mdiobus_phy_device_register
phy_device_register
mdiobus_register_device
mdio_device_reset <- mdio reset assert / deassert delay happens here
Add a 20ms enable delay to the regulator to fix the issue.
nfsd_cache_csum() currently assumes that the server's RPC layer has
been advancing rq_arg.head[0].iov_base as it decodes an incoming
request, because that's the way it used to work. On entry, it
expects that buf->head[0].iov_base points to the start of the NFS
header, and excludes the already-decoded RPC header.
These days however, head[0].iov_base now points to the start of the
RPC header during all processing. It no longer points at the NFS
Call header when execution arrives at nfsd_cache_csum().
In a retransmitted RPC the XID and the NFS header are supposed to
be the same as the original message, but the contents of the
retransmitted RPC header can be different. For example, for krb5,
the GSS sequence number will be different between the two. Thus if
the RPC header is always included in the DRC checksum computation,
the checksum of the retransmitted message might not match the
checksum of the original message, even though the NFS part of these
messages is identical.
The result is that, even if a matching XID is found in the DRC,
the checksum mismatch causes the server to execute the
retransmitted RPC transaction again.
Reviewed-by: Jeff Layton <jlayton@kernel.org> Tested-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "statp + 1" pointer that is passed to nfsd_cache_update() is
supposed to point to the start of the egress NFS Reply header. In
fact, it does point there for AUTH_SYS and RPCSEC_GSS_KRB5 requests.
But both krb5i and krb5p add fields between the RPC header's
accept_stat field and the start of the NFS Reply header. In those
cases, "statp + 1" points at the extra fields instead of the Reply.
The result is that nfsd_cache_update() caches what looks to the
client like garbage.
A connection break can occur for a number of reasons, but the most
common reason when using krb5i/p is a GSS sequence number window
underrun. When an underrun is detected, the server is obliged to
drop the RPC and the connection to force a retransmit with a fresh
GSS sequence number. The client presents the same XID, it hits in
the server's DRC, and the server returns the garbage cache entry.
The "statp + 1" argument has been used since the oldest changeset
in the kernel history repo, so it has been in nfsd_dispatch()
literally since before history began. The problem arose only when
the server-side GSS implementation was added twenty years ago.
Reviewed-by: Jeff Layton <jlayton@kernel.org> Tested-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__insert_pending() allocate memory in atomic context, so the allocation
could fail, but we are not handling that failure now. It could lead
ext4_es_remove_extent() to get wrong reserved clusters, and the global
data blocks reservation count will be incorrect. The same to
extents_status entry preallocation, preallocate pending entry out of the
i_es_lock with __GFP_NOFAIL, make sure __insert_pending() and
__revise_pending() always succeeds.
Yikebaer reported an issue:
==================================================================
BUG: KASAN: slab-use-after-free in ext4_es_insert_extent+0xc68/0xcb0
fs/ext4/extents_status.c:894
Read of size 4 at addr ffff888112ecc1a4 by task syz-executor/8438
The flow of issue triggering is as follows:
1. remove es
raw es es removed es1
|-------------------| -> |----|.......|------|
2. insert es
es insert es1 merge with es es1 merge with es and free es1
|----|.......|------| -> |------------|------| -> |-------------------|
es merges with newes, then merges with es1, frees es1, then determines
if es1->es_len is 0 and triggers a UAF.
The code flow is as follows:
ext4_es_insert_extent
es1 = __es_alloc_extent(true);
es2 = __es_alloc_extent(true);
__es_remove_extent(inode, lblk, end, NULL, es1)
__es_insert_extent(inode, &newes, es1) ---> insert es1 to es tree
__es_insert_extent(inode, &newes, es2)
ext4_es_try_to_merge_right
ext4_es_free_extent(inode, es1) ---> es1 is freed
if (es1 && !es1->es_len)
// Trigger UAF by determining if es1 is used.
We determine whether es1 or es2 is used immediately after calling
__es_remove_extent() or __es_insert_extent() to avoid triggering a
UAF if es1 or es2 is freed.
Reported-by: Yikebaer Aizezi <yikebaer61@gmail.com> Closes: https://lore.kernel.org/lkml/CALcu4raD4h9coiyEBL4Bm0zjDwxC2CyPiTwsP3zFuhot6y9Beg@mail.gmail.com Fixes: 2a69c450083d ("ext4: using nofail preallocation in ext4_es_insert_extent()") Cc: stable@kernel.org Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230815070808.3377171-1-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to in ext4_es_insert_delayed_block(), we use preallocations that
do not fail to avoid inconsistencies, but we do not care about es that are
not must be kept, and we return 0 even if such es memory allocation fails.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-9-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to in ext4_es_remove_extent(), we use a no-fail preallocation
to avoid inconsistencies, except that here we may have to preallocate
two extent_status.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-8-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
If __es_remove_extent() returns an error it means that when splitting
extent, allocating an extent that must be kept failed, where returning
an error directly would cause the extent tree to be inconsistent. So we
use GFP_NOFAIL to pre-allocate an extent_status and pass it to
__es_remove_extent() to avoid this problem.
In addition, since the allocated memory is outside the i_es_lock, the
extent_status tree may change and the pre-allocated extent_status is
no longer needed, so we release the pre-allocated extent_status when
es->es_len is not initialized.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-7-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
When splitting extent, if the second extent can not be dropped, we return
-ENOMEM and use GFP_NOFAIL to preallocate an extent_status outside of
i_es_lock and pass it to __es_remove_extent() to be used as the second
extent. This ensures that __es_remove_extent() is executed successfully,
thus ensuring consistency in the extent status tree. If the second extent
is not undroppable, we simply drop it and return 0. Then retry is no longer
necessary, remove it.
Now, __es_remove_extent() will always remove what it should, maybe more.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-6-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Pass a extent_status pointer prealloc to __es_insert_extent(). If the
pointer is non-null, it is used directly when a new extent_status is
needed to avoid memory allocation failures.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-5-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Factor out __es_alloc_extent() and __es_free_extent(), which only allocate
and free extent_status in these two helpers.
The ext4_es_alloc_extent() function is split into __es_alloc_extent()
and ext4_es_init_extent(). In __es_alloc_extent() we allocate memory using
GFP_KERNEL | __GFP_NOFAIL | __GFP_ZERO if the memory allocation cannot
fail, otherwise we use GFP_ATOMIC. and the ext4_es_init_extent() is used to
initialize extent_status and update related variables after a successful
allocation.
This is to prepare for the use of pre-allocated extent_status later.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-4-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
In the extent status tree, we have extents which we can just drop without
issues and extents we must not drop - this depends on the extent's status
- currently ext4_es_is_delayed() extents must stay, others may be dropped.
A helper function is added to help determine if the current extent can
be dropped, although only ext4_es_is_delayed() extents cannot be dropped
currently.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-3-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Right now we never release the power-domains properly on the error path.
Add a routine to be reused for this purpose and appropriate jumps in
probe() to run that routine where necessary.
Previously the jump label err_cleanup was used higher in the probe()
function to release the async notifier however the async notifier
registration was moved later in the code rendering the previous four jumps
redundant.
Rename the label from err_cleanup to err_v4l2_device_unregister to capture
what the jump does.
Fixes: 51397a4ec75d ("media: qcom: Initialise V4L2 async notifier later") Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fix old name in commit log: err_v4l2_device_register -> err_v4l2_device_unregister]
Stable-dep-of: f69791c39745 ("media: qcom: camss: Fix genpd cleanup") Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialise V4L2 async notifier and parse DT for async sub-devices later,
just before registering the notifier. This way the device can be made
available to the V4L2 async framework from the notifier init time onwards.
A subsequent patch will add struct v4l2_device as an argument to
v4l2_async_nf_init().
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
There are three cases of power domain management on supported platforms:
1) CAMSS on MSM8916, where a single VFE power domain is operated outside
of the camss device driver,
2) CAMSS on MSM8996 and SDM630/SDM660, where two VFE power domains are
managed separately by the camss device driver, the power domains are
linked and unlinked on demand by their functions vfe_pm_domain_on()
and vfe_pm_domain_off() respectively,
3) CAMSS on SDM845 and SM8250 platforms, and there are two VFE power
domains and their parent power domain TITAN_TOP, the latter one
shall be turned on prior to turning on any of VFE power domains.
Due to a previously missing link between TITAN_TOP and VFEx power domains
in the latter case, which is now fixed by [1], it was decided always to
turn on all found VFE power domains and TITAN_TOP power domain, even if
just one particular VFE is needed to be enabled or none of VFE power
domains are required, for instance the latter case is when vfe_lite is in
use. This misusage becomes more incovenient and clumsy, if next generations
are to be supported, for instance CAMSS on SM8450 has three VFE power
domains.
The change splits the power management support for platforms with TITAN_TOP
parent power domain, and, since 'power-domain-names' property is not
present in camss device tree nodes, the assumption is that the first
N power domains from the 'power-domains' list correspond to VFE power
domains, and, if the number of power domains is greater than number of
non-lite VFEs, then the last power domain from the list is the TITAN_TOP
power domain.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Stable-dep-of: f69791c39745 ("media: qcom: camss: Fix genpd cleanup") Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 411740f5422a ("KVM: MIPS/MMU: Implement KVM_CAP_SYNC_MMU")
old_pte is no longer used in kvm_mips_map_page(). So remove it to fix a
build warning about variable set but not used:
arch/mips/kvm/mmu.c: In function 'kvm_mips_map_page':
>> arch/mips/kvm/mmu.c:701:29: warning: variable 'old_pte' set but not used [-Wunused-but-set-variable]
701 | pte_t *ptep, entry, old_pte;
| ^~~~~~~
My last change in this area introduced a change which
accounted for primary channel in the interface ref count.
However, it did not reduce this ref count on deallocation
of the primary channel. i.e. during umount.
Fixing this leak here, by dropping this ref count for
primary channel while freeing up the session.
Fixes: fa1d0508bdd4 ("cifs: account for primary channel in the interface list") Cc: stable@vger.kernel.org Reported-by: Paulo Alcantara <pc@manguebit.com> Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The refcounting of server interfaces should account
for the primary channel too. Although this is not
strictly necessary, doing so will account for the primary
channel in DebugData.
Cc: stable@vger.kernel.org Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Today, if the server interfaces RSS capable, we simply
choose the fastest interface to setup a channel. This is not
a scalable approach, and does not make a lot of attempt to
distribute the connections.
This change does a weighted distribution of channels across
all the available server interfaces, where the weight is
a function of the advertised interface speed.
Also make sure that we don't mix rdma and non-rdma for channels.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: fa1d0508bdd4 ("cifs: account for primary channel in the interface list") Signed-off-by: Sasha Levin <sashal@kernel.org>
We store the last updated time for interface list while
parsing the interfaces. This change is to just print that
info in DebugData.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: fa1d0508bdd4 ("cifs: account for primary channel in the interface list") Signed-off-by: Sasha Levin <sashal@kernel.org>
When multiple mounts are to the same share from the same client it was not
possible to determine which section of /proc/fs/cifs/Stats (and DebugData)
correspond to that mount. In some recent examples this turned out to be
a significant problem when trying to analyze performance data - since
there are many cases where unless we know the tree id and session id we
can't figure out which stats (e.g. number of SMB3.1.1 requests by type,
the total time they take, which is slowest, how many fail etc.) apply to
which mount. The only existing loosely related ioctl CIFS_IOC_GET_MNT_INFO
does not return the information needed to uniquely identify which tcon
is which mount although it does return various flags and device info.
Add a cifs.ko ioctl CIFS_IOC_GET_TCON_INFO (0x800ccf0c) to return tid,
session id, tree connect count.
Cc: stable@vger.kernel.org Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
checkpatch showed formatting problems with extra spaces,
and extra semicolon and some missing blank lines in some
cifs headers.
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Reviewed-by: Germano Percossi <germano.percossi@gmail.com> Signed-off-by: Steve French <stfrench@microsoft.com>
Stable-dep-of: de4eceab578e ("smb3: allow dumping session and tcon id to improve stats analysis and debugging") Signed-off-by: Sasha Levin <sashal@kernel.org>
Kent reported an occasional KASAN splat in lockdep. Mark then noted:
> I suspect the dodgy access is to chain_block_buckets[-1], which hits the last 4
> bytes of the redzone and gets (incorrectly/misleadingly) attributed to
> nr_large_chain_blocks.
That would mean @size == 0, at which point size_to_bucket() returns -1
and the above happens.
alloc_chain_hlocks() has 'size - req', for the first with the
precondition 'size >= rq', which allows the 0.
This code is trying to split a block, del_chain_block() takes what we
need, and add_chain_block() puts back the remainder, except in the
above case the remainder is 0 sized and things go sideways.
Fixes: 810507fe6fd5 ("locking/lockdep: Reuse freed chain_hlocks entries") Reported-by: Kent Overstreet <kent.overstreet@linux.dev> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Kent Overstreet <kent.overstreet@linux.dev> Link: https://lkml.kernel.org/r/20231121114126.GH8262@noisy.programming.kicks-ass.net Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver needs to deregister and free the newly allocated dwc3 core
platform device on ACPI probe errors (e.g. probe deferral) and on driver
unbind but instead it leaked those resources while erroneously dropping
a reference to the parent platform device which is still in use.
For OF probing the driver takes a reference to the dwc3 core platform
device which has also always been leaked.
Fix the broken ACPI tear down and make sure to drop the dwc3 core
reference for both OF and ACPI.
Fixes: 8fd95da2cfb5 ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()") Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI") Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver") Cc: stable@vger.kernel.org # 4.18 Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Lee Jones <lee@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 9cf87666fc6e ("USB: dwc3: qcom: fix ACPI platform device leak") Signed-off-by: Sasha Levin <sashal@kernel.org>
The host and subsystem NQNs are passed in the connect command payload and
interpreted as nul-terminated strings. Ensure they actually are
nul-terminated before using them.
Fixes: a07b4970f464 "nvmet: add a generic NVMe target") Reported-by: Alon Zahavi <zahavi.alon@gmail.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.
Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.
Fixes: e284fc280473 ("i40e: Add and delete cloud filter") Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20231121211338.3348677-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In i40e_status removal patches, i40e_status conversion
to strings was removed in order to easily refactor
the code to use standard errornums. This however made it
more difficult for read error logs.
Use %pe formatter to print error messages in human-readable
format.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 4e20655e503e ("i40e: Fix adding unsupported cloud filters") Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_RODATA_FULL_DEFAULT_ENABLED=y, passing "rodata=on" on the
kernel command-line (rather than "rodata=full") should turn off the
"full" behaviour, leaving writable linear aliases of read-only kernel
memory. Unfortunately, the option has no effect in this situation and
the only way to disable the "rodata=full" behaviour is to disable rodata
protection entirely by passing "rodata=off".
Fix this by parsing the "on" and "off" options in the arch code,
additionally enforcing that 'rodata_full' cannot be set without also
setting 'rodata_enabled', allowing us to simplify a couple of checks
in the process.
Kfence only needs its pool to be mapped as page granularity, if it is
inited early. Previous judgement was a bit over protected. From [1], Mark
suggested to "just map the KFENCE region a page granularity". So I
decouple it from judgement and do page granularity mapping for kfence
pool only. Need to be noticed that late init of kfence pool still requires
page granularity mapping.
Page granularity mapping in theory cost more(2M per 1GB) memory on arm64
platform. Like what I've tested on QEMU(emulated 1GB RAM) with
gki_defconfig, also turning off rodata protection:
Before:
[root@liebao ]# cat /proc/meminfo
MemTotal: 999484 kB
After:
[root@liebao ]# cat /proc/meminfo
MemTotal: 1001480 kB
To implement this, also relocate the kfence pool allocation before the
linear mapping setting up, arm64_kfence_alloc_pool is to allocate phys
addr, __kfence_pool is to be set after linear mapping set up.
LINK: [1] https://lore.kernel.org/linux-arm-kernel/Y+IsdrvDNILA59UN@FVFF77S0Q05N/ Suggested-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Zhenhua Huang <quic_zhenhuah@quicinc.com> Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reviewed-by: Marco Elver <elver@google.com> Link: https://lore.kernel.org/r/1679066974-690-1-git-send-email-quic_zhenhuah@quicinc.com Signed-off-by: Will Deacon <will@kernel.org>
Stable-dep-of: acfa60dbe038 ("arm64: mm: Fix "rodata=on" when CONFIG_RODATA_FULL_DEFAULT_ENABLED=y") Signed-off-by: Sasha Levin <sashal@kernel.org>
AFS doesn't really do locking on R/O volumes as fileservers don't maintain
state with each other and thus a lock on a R/O volume file on one
fileserver will not be be visible to someone looking at the same file on
another fileserver.
Further, the server may return an error if you try it.
Fix this by doing what other AFS clients do and handle filelocking on R/O
volume files entirely within the client and don't touch the server.
Fixes: 6c6c1d63c243 ("afs: Provide mount-time configurable byte-range file locking emulation") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe") Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver") Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy") Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.
Fixes: f0a1913f8a6f ("octeontx2-pf: Add support for ethtool ntuple filters") Signed-off-by: Suman Ghosh <sumang@marvell.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20231121165624.3664182-1-sumang@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is quite obvious that this is a SMC DECLINE message, which means that
the applications received SMC protocol message.
We found that this was caused by the following situations:
As a result, a decline message was sent in the implementation, and this
message was read from TCP by the already-fallback connection.
This patch double the client timeout as 2x of the server value,
With this simple change, the Decline messages should never cross or
collide (during Confirm link timeout).
This issue requires an immediate solution, since the protocol updates
involve a more long-term solution.
Fixes: 0fb0b02bd6fd ("net/smc: adapt SMC client code to use the LLC flow") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Reviewed-by: Wen Gu <guwen@linux.alibaba.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver") Reported-by: Herb Wei <weihao.bj@ieisystem.com> Tested-by: Herb Wei <weihao.bj@ieisystem.com> Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com> Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
hid_debug_events_release releases resources bound to the HID device instance.
hid_device_release releases the underlying HID device instance potentially
before hid_debug_events_release has completed releasing debug resources bound
to the same HID device instance.
Reference count to prevent the HID device instance from being torn down
preemptively when HID debugging support is used. When count reaches zero,
release core resources of HID device instance using hiddev_free.
The only task of intel_gt_release_all is to zero gt table. Calling
it on error path prevents intel_gt_driver_late_release_all (called from
i915_driver_late_release) to cleanup GTs, causing leakage.
After i915_driver_late_release GT array is not used anymore so
it does not need cleaning at all.
During 'ifconfig <netdev> down' one RSS memory was not getting freed.
This patch fixes the same.
Fixes: 81a4362016e7 ("octeontx2-pf: Add RSS multi group support") Signed-off-by: Suman Ghosh <sumang@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
wg_xmit() can be called concurrently, KCSAN reported [1]
some device stats updates can be lost.
Use DEV_STATS_INC() for this unlikely case.
[1]
BUG: KCSAN: data-race in wg_xmit / wg_xmit
read-write to 0xffff888104239160 of 8 bytes by task 1375 on cpu 0:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
read-write to 0xffff888104239160 of 8 bytes by task 1378 on cpu 1:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
v2: also change wg_packet_consume_data_done() (Hangbin Liu)
and wg_packet_purge_staged_packets()
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Innolux G101ICE-L01 datasheet [1] page 17 table
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
indicates that maximum vertical blanking time is 40 lines.
Currently the driver uses 29 lines.
Fix it, and since this panel is a DE panel, adjust the timings
to make them less hostile to controllers which cannot do 1 px
HSA/VSA, distribute the delays evenly between all three parts.
For "boe,tv105wum-nw0" this special panel, it is stipulated in
the panel spec that MIPI needs to keep the LP11 state before
the lcm_reset pin is pulled high.
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230515094955.15982-3-shuijing.li@mediatek.com
Stable-dep-of: 6965809e5269 ("drm/panel: auo,b101uan08.3: Fine tune the panel power sequence") Signed-off-by: Sasha Levin <sashal@kernel.org>
When kafs tries to look up a cell in the DNS or the local config, it will
translate a lookup failure into EDESTADDRREQ whereas OpenAFS translates it
into ENOENT. Applications such as West expect the latter behaviour and
fail if they see the former.
This can be seen by trying to mount an unknown cell:
# mount -t afs %example.com:cell.root /mnt
mount: /mnt: mount(2) system call failed: Destination address required.
Fixes: 4d673da14533 ("afs: Support the AFS dynamic root") Reported-by: Markus Suvanto <markus.suvanto@gmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216637 Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
As of commit 2ac874343749 ("RISC-V: split early & late of_node to
hartid mapping") my CI complains about newly added pr_err() messages
during boot, for example:
[ 0.000000] Couldn't find cpu id for hartid [0]
[ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller
Before the split, riscv_of_processor_hartid() contained a check for
whether the cpu was "available", before calling riscv_hartid_to_cpuid(),
but after the split riscv_of_processor_hartid() can be called for cpus
that are disabled.
Most callers of riscv_hartid_to_cpuid() already report custom errors
where it falls, making this print superfluous in those case. In other
places, the print adds nothing - see riscv_intc_init() for example.
Fixes: 2ac874343749 ("RISC-V: split early & late of_node to hartid mapping") Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20230629-paternity-grafted-b901b76d04a0@wendy Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In devm_cxl_add_port() the port creation may fail and its associated
pointer does not contain a valid address. During error message
generation this invalid port address is used. Fix that wrong address
access.
Fixes: f3cd264c4ec1 ("cxl: Unify debug messages when calling devm_cxl_add_port()") Signed-off-by: Robert Richter <rrichter@amd.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20230519215436.3394532-1-rrichter@amd.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to a flaw in the hardware design, the GL9755 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9755
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: 36ed2fd32b2c ("mmc: sdhci-pci-gli: A workaround to allow GL9755 to enter ASPM L1.2") Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20231107095741.8832-3-victorshihgli@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Change directory to the tracefs directory
2. Create a kprobe event (doesn't matter what one)
3. Open bash file descriptor 5 on the enable file of the kprobe event
4. Delete the kprobe event (removes the files too)
5. Close the bash file descriptor 5
What happens here is that the kprobe event creates a trace_event_file
"file" descriptor that represents the file in tracefs to the event. It
maintains state of the event (is it enabled for the given instance?).
Opening the "enable" file gets a reference to the event "file" descriptor
via the open file descriptor. When the kprobe event is deleted, the file is
also deleted from the tracefs system which also frees the event "file"
descriptor.
But as the tracefs file is still opened by user space, it will not be
totally removed until the final dput() is called on it. But this is not
true with the event "file" descriptor that is already freed. If the user
does a write to or simply closes the file descriptor it will reference the
event "file" descriptor that was just freed, causing a use-after-free bug.
To solve this, add a ref count to the event "file" descriptor as well as a
new flag called "FREED". The "file" will not be freed until the last
reference is released. But the FREE flag will be set when the event is
removed to prevent any more modifications to that event from happening,
even if there's still a reference to the event "file" descriptor.
As reported by Mahesh & Aneesh, opal_prd_msg_notifier() triggers a
FORTIFY_SOURCE warning:
memcpy: detected field-spanning write (size 32) of single field "&item->msg" at arch/powerpc/platforms/powernv/opal-prd.c:355 (size 4)
WARNING: CPU: 9 PID: 660 at arch/powerpc/platforms/powernv/opal-prd.c:355 opal_prd_msg_notifier+0x174/0x188 [opal_prd]
NIP opal_prd_msg_notifier+0x174/0x188 [opal_prd]
LR opal_prd_msg_notifier+0x170/0x188 [opal_prd]
Call Trace:
opal_prd_msg_notifier+0x170/0x188 [opal_prd] (unreliable)
notifier_call_chain+0xc0/0x1b0
atomic_notifier_call_chain+0x2c/0x40
opal_message_notify+0xf4/0x2c0
This happens because the copy is targeting item->msg, which is only 4
bytes in size, even though the enclosing item was allocated with extra
space following the msg.
To fix the warning define struct opal_prd_msg with a union of the header
and a flex array, and have the memcpy target the flex array.
[WHY]
Flush command sent to DMCUB spends more time for execution on
a dGPU than on an APU. This causes cursor lag when using high
refresh rate mouses.
[HOW]
1. Change the DMCUB mailbox memory location from FB to inbox.
2. Only change windows memory to inbox.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Lewis Huang <lewis.huang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
When cursor moves across screen boarder, lag cursor observed,
since subvp settings need to sync up with vblank that causes
cursor updates being delayed.
[HOW]
Enable fast plane updates on DCN3.2 to fix it.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Tianci Yin <tianci.yin@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ddc_service_construct() is called, it explicitly checks both the
link type and whether there is something on the link which will
dictate whether the pin is marked as hw_supported.
If the pin isn't set or the link is not set (such as from
unloading/reloading amdgpu in an IGT test) then fail the
amdgpu_dm_i2c_xfer() call.
Cc: stable@vger.kernel.org Fixes: 22676bc500c2 ("drm/amd/display: Fix dmub soft hang for PSR 1") Link: https://github.com/fwupd/fwupd/issues/6327 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Otherwise userspace can spam the logs by using incorrect input values.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not leak the pointer where we couldn't grab the reference
on to the caller because it can be that the error handling still
tries to put the reference then.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ATRM ACPI method is for fetching the dGPU vbios rom
image on laptops and all-in-one systems. It should not be
used for external add in cards. If the dGPU is thunderbolt
connected, don't try ATRM.
v2: pci_is_thunderbolt_attached only works for Intel. Use
pdev->external_facing instead.
v3: dev_is_removable() seems to be what we want
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2925 Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log