Set supports_autosuspend = 1 for the rtl8152_cfgselector_driver.
Fixes: ec51fbd1b8a2 ("r8152: add USB device driver for config selection") Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit ec51fbd1b8a2 ("r8152: add USB device driver for
config selection"), the code about changing USB configuration
in rtl_vendor_mode() wouldn't be run anymore. Therefore, the
function could be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtl8152_cfgselector_probe() should set the USB configuration to the
vendor mode only for the devices which the driver (r8152) supports.
Otherwise, no driver would be used for such devices.
Fixes: ec51fbd1b8a2 ("r8152: add USB device driver for config selection") Signed-off-by: Hayes Wang <hayeswang@realtek.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rb_time_cmpxchg() on 32-bit architectures requires setting three
32-bit words to represent the 64-bit timestamp, with some salt for
synchronization. Those are: msb, top, and bottom
The issue is, the rb_time_cmpxchg() did not properly salt the msb portion,
and the msb that was written was stale.
Link: https://lore.kernel.org/linux-trace-kernel/20231215084114.20899342@rorschach.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: f03f2abce4f39 ("ring-buffer: Have 32 bit time stamps use all 64 bits") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an update to an event is interrupted by another event between the time
the initial event allocated its buffer and where it wrote to the
write_stamp, the code try to reset the write stamp back to the what it had
just overwritten. It knows that it was overwritten via checking the
before_stamp, and if it didn't match what it wrote to the before_stamp
before it allocated its space, it knows it was overwritten.
To put back the write_stamp, it uses the before_stamp it read. The problem
here is that by writing the before_stamp to the write_stamp it makes the
two equal again, which means that the write_stamp can be considered valid
as the last timestamp written to the ring buffer. But this is not
necessarily true. The event that interrupted the event could have been
interrupted in a way that it was interrupted as well, and can end up
leaving with an invalid write_stamp. But if this happens and returns to
this context that uses the before_stamp to update the write_stamp again,
it can possibly incorrectly make it valid, causing later events to have in
correct time stamps.
As it is OK to leave this function with an invalid write_stamp (one that
doesn't match the before_stamp), there's no reason to try to make it valid
again in this case. If this race happens, then just leave with the invalid
write_stamp and the next event to come along will just add a absolute
timestamp and validate everything again.
Bonus points: This gets rid of another cmpxchg64!
Link: https://lore.kernel.org/linux-trace-kernel/20231214222921.193037a7@gandalf.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Vincent Donnefort <vdonnefort@google.com> Fixes: a389d86f7fd09 ("ring-buffer: Have nested events still record running time stamp") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
/* The cmpxchg always fails if it interrupted an update */
if (!__rb_time_read(t, &val, &cnt2))
return false;
if (val != expect)
return false;
<<<< interrupted here!
cnt = local_read(&t->cnt);
The problem is that the synchronization counter in the rb_time_t is read
*after* the value of the timestamp is read. That means if an interrupt
were to come in between the value being read and the counter being read,
it can change the value and the counter and the interrupted process would
be clueless about it!
The counter needs to be read first and then the value. That way it is easy
to tell if the value is stale or not. If the counter hasn't been updated,
then the value is still good.
The maximum ring buffer data size is the maximum size of data that can be
recorded on the ring buffer. Events must be smaller than the sub buffer
data size minus any meta data. This size is checked before trying to
allocate from the ring buffer because the allocation assumes that the size
will fit on the sub buffer.
The maximum size was calculated as the size of a sub buffer page (which is
currently PAGE_SIZE minus the sub buffer header) minus the size of the
meta data of an individual event. But it missed the possible adding of a
time stamp for events that are added long enough apart that the event meta
data can't hold the time delta.
When an event is added that is greater than the current BUF_MAX_DATA_SIZE
minus the size of a time stamp, but still less than or equal to
BUF_MAX_DATA_SIZE, the ring buffer would go into an infinite loop, looking
for a page that can hold the event. Luckily, there's a check for this loop
and after 1000 iterations and a warning is emitted and the ring buffer is
disabled. But this should never happen.
This can happen when a large event is added first, or after a long period
where an absolute timestamp is prefixed to the event, increasing its size
by 8 bytes. This passes the check and then goes into the algorithm that
causes the infinite loop.
For events that are the first event on the sub-buffer, it does not need to
add a timestamp, because the sub-buffer itself contains an absolute
timestamp, and adding one is redundant.
The fix is to check if the event is to be the first event on the
sub-buffer, and if it is, then do not add a timestamp.
This also fixes 32 bit adding a timestamp when a read of before_stamp or
write_stamp is interrupted. There's still no need to add that timestamp if
the event is going to be the first event on the sub buffer.
Also, if the buffer has "time_stamp_abs" set, then also check if the
length plus the timestamp is greater than the BUF_MAX_DATA_SIZE.
For the ring buffer iterator (non-consuming read), the event needs to be
copied into the iterator buffer to make sure that a writer does not
overwrite it while the user is reading it. If a write happens during the
copy, the buffer is simply discarded.
But the temp buffer itself was not big enough. The allocation of the
buffer was only BUF_MAX_DATA_SIZE, which is the maximum data size that can
be passed into the ring buffer and saved. But the temp buffer needs to
hold the meta data as well. That would be BUF_PAGE_SIZE and not
BUF_MAX_DATA_SIZE.
The ring buffer timestamps are synchronized by two timestamp placeholders.
One is the "before_stamp" and the other is the "write_stamp" (sometimes
referred to as the "after stamp" but only in the comments. These two
stamps are key to knowing how to handle nested events coming in with a
lockless system.
When moving across sub-buffers, the before stamp is updated but the write
stamp is not. There's an effort to put back the before stamp to something
that seems logical in case there's nested events. But as the current event
is about to cross sub-buffers, and so will any new nested event that happens,
updating the before stamp is useless, and could even introduce new race
conditions.
The first event on a sub-buffer simply uses the sub-buffer's timestamp
and keeps a "delta" of zero. The "before_stamp" and "write_stamp" are not
used in the algorithm in this case. There's no reason to try to fix the
before_stamp when this happens.
As a bonus, it removes a cmpxchg() when crossing sub-buffers!
Link: https://lore.kernel.org/linux-trace-kernel/20231211114420.36dde01b@gandalf.local.home Cc: stable@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: a389d86f7fd09 ("ring-buffer: Have nested events still record running time stamp") Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The snapshot buffer is to mimic the main buffer so that when a snapshot is
needed, the snapshot and main buffer are swapped. When the snapshot buffer
is allocated, it is set to the minimal size that the ring buffer may be at
and still functional. When it is allocated it becomes the same size as the
main ring buffer, and when the main ring buffer changes in size, it should
do.
Currently, the resize only updates the snapshot buffer if it's used by the
current tracer (ie. the preemptirqsoff tracer). But it needs to be updated
anytime it is allocated.
When changing the size of the main buffer, instead of looking to see if
the current tracer is utilizing the snapshot buffer, just check if it is
allocated to know if it should be updated or not.
Also fix typo in comment just above the code change.
Reading the ring buffer does a swap of a sub-buffer within the ring buffer
with a empty sub-buffer. This allows the reader to have full access to the
content of the sub-buffer that was swapped out without having to worry
about contention with the writer.
The readers call ring_buffer_alloc_read_page() to allocate a page that
will be used to swap with the ring buffer. When the code is finished with
the reader page, it calls ring_buffer_free_read_page(). Instead of freeing
the page, it stores it as a spare. Then next call to
ring_buffer_alloc_read_page() will return this spare instead of calling
into the memory management system to allocate a new page.
Unfortunately, on freeing of the ring buffer, this spare page is not
freed, and causes a memory leak.
Link: https://lore.kernel.org/linux-trace-kernel/20231210221250.7b9cc83c@rorschach.local.home Cc: stable@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: 73a757e63114d ("ring-buffer: Return reader page back into existing ring buffer") Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Validate @ioctl_rsp->OutputOffset and @ioctl_rsp->OutputCount so that
their sum does not wrap to a number that is smaller than @reparse_buf
and we end up with a wild pointer as follows:
Fixes: 2e4564b31b64 ("smb3: add support for stat of WSL reparse points for special file types") Cc: stable@vger.kernel.org Reported-by: Robert Morris <rtm@csail.mit.edu> Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If server replied SMB2_NEGOTIATE with a zero SecurityBufferOffset,
smb2_get_data_area() sets @len to non-zero but return NULL, so
decode_negTokeninit() ends up being called with a NULL @security_blob:
Fix this by setting @len to zero when @off == 0 so callers won't
attempt to dereference non-existing data areas.
Reported-by: Robert Morris <rtm@csail.mit.edu> Cc: stable@vger.kernel.org Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ADL+ the hardware automagically calculates the CCS AUX surface
stride from the main surface stride, so when remapping we can't
really play a lot of tricks with the main surface stride, or else
the AUX surface stride would get miscalculated and no longer
match the actual data layout in memory.
Supposedly we could remap in 256 main surface tile units
(AUX page(4096)/cachline(64)*4(4x1 main surface tiles per
AUX cacheline)=256 main surface tiles), but the extra complexity
is probably not worth the hassle.
So let's just make sure our mapping stride is calculated from
the full framebuffer stride (instead of the framebuffer width).
This way the stride we program into PLANE_STRIDE will be the
original framebuffer stride, and thus there will be no change
to the AUX stride/layout.
When screen brightness is rapidly changed and PSR-SU is enabled the
display hangs on panels with this TCON even on the latest DCN 3.1.4
microcode (0x8002a81 at this time).
This was disabled previously as commit 072030b17830 ("drm/amd: Disable
PSR-SU on Parade 0803 TCON") but reverted as commit 1e66a17ce546 ("Revert
"drm/amd: Disable PSR-SU on Parade 0803 TCON"") in favor of testing for
a new enough microcode (commit cd2e31a9ab93 ("drm/amd/display: Set minimum
requirement for using PSR-SU on Phoenix")).
As hangs are still happening specifically with this TCON, disable PSR-SU
again for it until it can be root caused.
Cc: stable@vger.kernel.org Cc: aaron.ma@canonical.com Cc: binli@gnome.org Cc: Marc Rossi <Marc.Rossi@amd.com> Cc: Hamza Mahfooz <Hamza.Mahfooz@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2046131 Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When freeing PD/PT with shadows it can happen that the shadow
destruction races with detaching the PD/PT from the VM causing a NULL
pointer dereference in the invalidation code.
Fix this by detaching the the PD/PT from the VM first and then
freeing the shadow instead.
Signed-off-by: Christian König <christian.koenig@amd.com> Fixes: https://gitlab.freedesktop.org/drm/amd/-/issues/2867 Cc: <stable@vger.kernel.org> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EXTENT_QGROUP_RESERVED bit is used to "lock" regions of the file for
duplicate reservations. That is two writes to that range in one
transaction shouldn't create two reservations, as the reservation will
only be freed once when the write finally goes down. Therefore, it is
never OK to clear that bit without freeing the associated qgroup
reserve. At this point, we don't want to be freeing the reserve, so mask
off the bit.
CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Boris Burkov <boris@bur.io> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An ordered extent completing is a critical moment in qgroup reserve
handling, as the ownership of the reservation is handed off from the
ordered extent to the delayed ref. In the happy path we release (unlock)
but do not free (decrement counter) the reservation, and the delayed ref
drives the free. However, on an error, we don't create a delayed ref,
since there is no ref to add. Therefore, free on the error path.
CC: stable@vger.kernel.org # 6.1+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Boris Burkov <boris@bur.io> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split folios during the second loop of shmem_undo_range. It's not
sufficient to only split folios when dealing with partial pages, since
it's possible for a THP to be faulted in after that point. Calling
truncate_inode_folio in that situation can result in throwing away data
outside of the range being targeted.
[akpm@linux-foundation.org: tidy up comment layout] Link: https://lkml.kernel.org/r/20230418084031.3439795-1-stevensd@google.com Fixes: b9a8a4195c7d ("truncate,shmem: Handle truncates that split large folios") Signed-off-by: David Stevens <stevensd@chromium.org> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Suleiman Souhlal <suleiman@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unmapped folios accessed through file descriptors can be underprotected.
Those folios are added to the oldest generation based on:
1. The fact that they are less costly to reclaim (no need to walk the
rmap and flush the TLB) and have less impact on performance (don't
cause major PFs and can be non-blocking if needed again).
2. The observation that they are likely to be single-use. E.g., for
client use cases like Android, its apps parse configuration files
and store the data in heap (anon); for server use cases like MySQL,
it reads from InnoDB files and holds the cached data for tables in
buffer pools (anon).
However, the oldest generation can be very short lived, and if so, it
doesn't provide the PID controller with enough time to respond to a surge
of refaults. (Note that the PID controller uses weighted refaults and
those from evicted generations only take a half of the whole weight.) In
other words, for a short lived generation, the moving average smooths out
the spike quickly.
To fix the problem:
1. For folios that are already on LRU, if they can be beyond the
tracking range of tiers, i.e., five accesses through file
descriptors, move them to the second oldest generation to give them
more time to age. (Note that tiers are used by the PID controller
to statistically determine whether folios accessed multiple times
through file descriptors are worth protecting.)
2. When adding unmapped folios to LRU, adjust the placement of them so
that they are not too close to the tail. The effect of this is
similar to the above.
On Android, launching 55 apps sequentially:
Before After Change
workingset_refault_anon 2564102425598972 0%
workingset_refault_file 115016834106178438 -8%
Link: https://lkml.kernel.org/r/20231208061407.2125867-1-yuzhao@google.com Fixes: ac35a4902374 ("mm: multi-gen LRU: minimal implementation") Signed-off-by: Yu Zhao <yuzhao@google.com> Reported-by: Charan Teja Kalla <quic_charante@quicinc.com> Tested-by: Kalesh Singh <kaleshsingh@google.com> Cc: T.J. Mercier <tjmercier@google.com> Cc: Kairui Song <ryncsn@gmail.com> Cc: Hillf Danton <hdanton@sina.com> Cc: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stm32_dma_get_burst() returns a negative error for invalid input, which
gets turned into a large u32 value in stm32_dma_prep_dma_memcpy() that
in turn triggers an assertion because it does not fit into a two-bit field:
drivers/dma/stm32-dma.c: In function 'stm32_dma_prep_dma_memcpy':
include/linux/compiler_types.h:354:38: error: call to '__compiletime_assert_282' declared with attribute error: FIELD_PREP: value too large for the field
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^
include/linux/compiler_types.h:335:4: note: in definition of macro '__compiletime_assert'
prefix ## suffix(); \
^~~~~~
include/linux/compiler_types.h:354:2: note: in expansion of macro '_compiletime_assert'
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
^~~~~~~~~~~~~~~~~~~
include/linux/build_bug.h:39:37: note: in expansion of macro 'compiletime_assert'
#define BUILD_BUG_ON_MSG(cond, msg) compiletime_assert(!(cond), msg)
^~~~~~~~~~~~~~~~~~
include/linux/bitfield.h:68:3: note: in expansion of macro 'BUILD_BUG_ON_MSG'
BUILD_BUG_ON_MSG(__builtin_constant_p(_val) ? \
^~~~~~~~~~~~~~~~
include/linux/bitfield.h:114:3: note: in expansion of macro '__BF_FIELD_CHECK'
__BF_FIELD_CHECK(_mask, 0ULL, _val, "FIELD_PREP: "); \
^~~~~~~~~~~~~~~~
drivers/dma/stm32-dma.c:1237:4: note: in expansion of macro 'FIELD_PREP'
FIELD_PREP(STM32_DMA_SCR_PBURST_MASK, dma_burst) |
^~~~~~~~~~
As an easy workaround, assume the error can happen, so try to handle this
by failing stm32_dma_prep_dma_memcpy() before the assertion. It replicates
what is done in stm32_dma_set_xfer_param() where stm32_dma_get_burst() is
also used.
Add begin/end_use ring callbacks to disallow GFXOFF when
SDMA work is submitted and allow it again afterward.
This should avoid corner cases where GFXOFF is erroneously
entered when SDMA is still active. For now just allow/disallow
GFXOFF in the begin and end helpers until we root cause the
issue. This should not impact power as SDMA usage is pretty
minimal and GFXOSS should not be active when SDMA is active
anyway, this just makes it explicit.
v2: move everything into sdma5.2 code. No reason for this
to be generic at this point.
v3: Add comments in new code
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2220 Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> (v1) Tested-by: Mario Limonciello <mario.limonciello@amd.com> (v1) Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 5.15+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In __team_options_register, team_options are allocated and appended to
the team's option_list.
If one option instance allocation fails, the "inst_rollback" cleanup
path frees the previously allocated options but doesn't remove them from
the team's option_list.
This leaves dangling pointers that can be dereferenced later by other
parts of the team driver that iterate over options.
This patch fixes the cleanup path to remove the dangling pointers from
the list.
As far as I can tell, this uaf doesn't have much security implications
since it would be fairly hard to exploit (an attacker would need to make
the allocation of that specific small object fail) but it's still nice
to fix.
Cc: stable@vger.kernel.org Fixes: 80f7c6683fe0 ("team: add support for per-port options") Signed-off-by: Florent Revest <revest@chromium.org> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://lore.kernel.org/r/20231206123719.1963153-1-revest@chromium.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is currently possible for a userspace application to enter an
infinite page fault loop when using HugeTLB pages implemented with
contiguous PTEs when HAFDBS is not available. This happens because:
1. The kernel may sometimes write PTEs that are sw-dirty but hw-clean
(PTE_DIRTY | PTE_RDONLY | PTE_WRITE).
2. If, during a write, the CPU uses a sw-dirty, hw-clean PTE in handling
the memory access on a system without HAFDBS, we will get a page
fault.
3. HugeTLB will check if it needs to update the dirty bits on the PTE.
For contiguous PTEs, it will check to see if the pgprot bits need
updating. In this case, HugeTLB wants to write a sequence of
sw-dirty, hw-dirty PTEs, but it finds that all the PTEs it is about
to overwrite are all pte_dirty() (pte_sw_dirty() => pte_dirty()),
so it thinks no update is necessary.
We can get the kernel to write a sw-dirty, hw-clean PTE with the
following steps (showing the relevant VMA flags and pgprot bits):
ii. mprotect the VMA to PROT_NONE.
VMA vmflags: VM_SHARED
VMA pgprot bits: PTE_RDONLY
PTE pgprot bits: PTE_DIRTY | PTE_RDONLY
iii. mprotect the VMA back to PROT_READ | PROT_WRITE.
VMA vmflags: VM_SHARED | VM_READ | VM_WRITE
VMA pgprot bits: PTE_RDONLY | PTE_WRITE
PTE pgprot bits: PTE_DIRTY | PTE_WRITE | PTE_RDONLY
Make it impossible to create a writeable sw-dirty, hw-clean PTE with
pte_modify(). Such a PTE should be impossible to create, and there may
be places that assume that pte_dirty() implies pte_hw_dirty().
Signed-off-by: James Houghton <jthoughton@google.com> Fixes: 031e6e6b4e12 ("arm64: hugetlb: Avoid unnecessary clearing in huge_ptep_set_access_flags") Cc: <stable@vger.kernel.org> Acked-by: Will Deacon <will@kernel.org> Reviewed-by: Ryan Roberts <ryan.roberts@arm.com> Link: https://lore.kernel.org/r/20231204172646.2541916-3-jthoughton@google.com Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For files with logical blocks close to EXT_MAX_BLOCKS, the file size
predicted in ext4_mb_normalize_request() may exceed EXT_MAX_BLOCKS.
This can cause some blocks to be preallocated that will not be used.
And after [Fixes], the following issue may be triggered:
The problem is that when orig_goal_end is subtracted from ac_b_ex.fe_len
it is still greater than EXT_MAX_BLOCKS, which causes ex.fe_logical to
overflow to a very small value, which ultimately triggers a BUG_ON in
ext4_mb_new_inode_pa() because pa->pa_free < len.
The last logical block of an actual write request does not exceed
EXT_MAX_BLOCKS, so in ext4_mb_normalize_request() also avoids normalizing
the last logical block to exceed EXT_MAX_BLOCKS to avoid the above issue.
The test case in [Link] can reproduce the above issue with 64k block size.
If bus is marked as multi_link, but number of masters in the stream is
not higher than bus->hw_sync_min_links (bus->multi_link && m_rt_count >=
bus->hw_sync_min_links), bank switching should not happen. The first
part of do_bank_switch() code properly takes these conditions into
account, but second part (sdw_ml_sync_bank_switch()) relies purely on
bus->multi_link property. This is not balanced and leads to NULL
pointer dereference:
Fixes: ce6e74d008ff ("soundwire: Add support for multi link bank switch") Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20231124180136.390621-1-krzysztof.kozlowski@linaro.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our btrfs subvolume snapshot <source> <destination> utility enforces
that <source> is the root of the subvolume, however this isn't enforced
in the kernel. Update the kernel to also enforce this limitation to
avoid problems with other users of this ioctl that don't have the
appropriate checks in place.
Reported-by: Martin Michaelis <code@mgjm.de> CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Neal Gompa <neal@gompa.dev> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When lockdep is enabled, the for_each_sibling_event(sibling, event)
macro checks that event->ctx->mutex is held. When creating a new group
leader event, we call perf_event_validate_size() on a partially
initialized event where event->ctx is NULL, and so when
for_each_sibling_event() attempts to check event->ctx->mutex, we get a
splat, as reported by Lucas De Marchi:
WARNING: CPU: 8 PID: 1471 at kernel/events/core.c:1950 __do_sys_perf_event_open+0xf37/0x1080
This only happens for a new event which is its own group_leader, and in
this case there cannot be any sibling events. Thus it's safe to skip the
check for siblings, which avoids having to make invasive and ugly
changes to for_each_sibling_event().
Avoid the splat by bailing out early when the new event is its own
group_leader.
Fixes: 382c27f4ed28f803 ("perf: Fix perf_event_validate_size()") Closes: https://lore.kernel.org/lkml/20231214000620.3081018-1-lucas.demarchi@intel.com/ Closes: https://lore.kernel.org/lkml/ZXpm6gQ%2Fd59jGsuW@xpf.sh.intel.com/ Reported-by: Lucas De Marchi <lucas.demarchi@intel.com> Reported-by: Pengfei Xu <pengfei.xu@intel.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20231215112450.3972309-1-mark.rutland@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function asus_kbd_set_report the parameter buf is read-only
as it gets copied in a memory portion suitable for USB transfer,
but the parameter is not marked as const: add the missing const and mark
const immutable buffers passed to that function.
Signed-off-by: Denis Benato <benato.denis96@gmail.com> Signed-off-by: Luke D. Jones <luke@ljones.dev> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Rebind it to qmi_wwan after freeing it up
from option driver.
The proper configuration is:
Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI
We really don't want to do atomic_read() or anything like that, since we
already have the value, not the lock. The whole point of this is that
we've loaded the lock from memory, and we want to check whether the
value we loaded was a locked one or not.
The main use of this is the lockref code, which loads both the lock and
the reference count in one atomic operation, and then works on that
combined value. With the atomic_read(), the compiler would pointlessly
spill the value to the stack, in order to then be able to read it back
"atomically".
This is the qspinlock version of commit c6f4a9002252 ("asm-generic:
ticket-lock: Optimize arch_spin_value_unlocked()") which fixed this same
bug for ticket locks.
Honor MagicBook 13 2023 has a touchpad which do not switch to the multitouch
mode until the input mode feature is written by the host. The touchpad do
report the input mode at touchpad(3), while itself working under mouse mode. As
a workaround, it is possible to call MT_QUIRE_FORCE_GET_FEATURE to force set
feature in mt_set_input_mode for such device.
The touchpad reports as BLTP7853, which cannot retrive any useful manufacture
information on the internel by this string at present. As the serial number of
the laptop is GLO-G52, while DMI info reports the laptop serial number as
GLO-GXXX, this workaround should applied to all models which has the GLO-GXXX.
Some devices managed by this driver automatically set brightness to 0
before entering a suspended state and reset it back to a default
brightness level after the resume:
this has the effect of having the kernel report wrong brightness
status after a sleep, and on some devices (like the Asus RC71L) that
brightness is the intensity of LEDs directly facing the user.
Fix the above issue by setting back brightness to the level it had
before entering a sleep state.
Signed-off-by: Denis Benato <benato.denis96@gmail.com> Signed-off-by: Luke D. Jones <luke@ljones.dev> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a socket is processing ioctl 'NBD_SET_SOCK', config->socks might be
krealloc in nbd_add_socket(), and a garbage request is received now, a UAF
may occurs.
Pass nbd_sock to nbd_read_reply(). And introduce a new function
sock_xmit_recv(), which differs from sock_xmit only in the way it get
socket.
==================================================================
BUG: KASAN: use-after-free in sock_xmit+0x525/0x550
Read of size 8 at addr ffff8880188ec428 by task kworker/u12:1/18779
The Glorious Model I mouse has a buggy HID report descriptor for its
keyboard endpoint (used for programmable buttons). For report ID 2, there
is a mismatch between Logical Minimum and Usage Minimum in the array that
reports keycodes.
The offending portion of the descriptor: (from hid-decode)
This bug shifts all programmed keycodes up by 1. Importantly, this causes
"empty" array indexes of 0x00 to be interpreted as 0x01, ErrorRollOver.
The presence of ErrorRollOver causes the system to ignore all keypresses
from the endpoint and breaks the ability to use the programmable buttons.
Setting byte 41 to 0x00 fixes this, and causes keycodes to be interpreted
correctly.
Also, USB_VENDOR_ID_GLORIOUS is changed to USB_VENDOR_ID_SINOWEALTH,
and a new ID for Laview Technology is added. Glorious seems to be
white-labeling controller boards or mice from these vendors. There isn't a
single canonical vendor ID for Glorious products.
core.c:116: warning: Function parameter or member 'ioss_evtconfig' not described in 'telemetry_update_events'
core.c:188: warning: Function parameter or member 'ioss_evtconfig' not described in 'telemetry_get_eventconfig'
It looks like it were copy'n'paste typos when these descriptions
had been introduced. Fix the typos.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202310070743.WALmRGSY-lkp@intel.com/ Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20231120150756.1661425-1-andriy.shevchenko@linux.intel.com Reviewed-by: Rajneesh Bhardwaj <irenic.rajneesh@gmail.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a cpu is hot-unplugged, it is put in idle state and the function
arch_cpu_idle_dead() is called. The timer interrupt for this processor
should be disabled, otherwise there will be pending timer interrupt for
the unplugged cpu, so that vcpu is prevented from giving up scheduling
when system is running in vm mode.
This patch implements the timer shutdown interface so that the constant
timer will be properly disabled when a CPU is hot-unplugged.
Reviewed-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Bibo Mao <maobibo@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a preparatory change. A follow-up patch "bpf: verify callbacks
as if they are called unknown number of times" changes logic for
callbacks handling. While previously callbacks were verified as a
single function call, new scheme takes into account that callbacks
could be executed unknown number of times.
This has dire implications for bpf_loop_bench:
SEC("fentry/" SYS_PREFIX "sys_getpgid")
int benchmark(void *ctx)
{
for (int i = 0; i < 1000; i++) {
bpf_loop(nr_loops, empty_callback, NULL, 0);
__sync_add_and_fetch(&hits, nr_loops);
}
return 0;
}
W/o callbacks change verifier sees it as a 1000 calls to
empty_callback(). However, with callbacks change things become
exponential:
- i=0: state exploring empty_callback is scheduled with i=0 (a);
- i=1: state exploring empty_callback is scheduled with i=1;
...
- i=999: state exploring empty_callback is scheduled with i=999;
- state (a) is popped from stack;
- i=1: state exploring empty_callback is scheduled with i=1;
...
Avoid this issue by rewriting outer loop as bpf_loop().
Unfortunately, this adds a function call to a loop at runtime, which
negatively affects performance:
throughput latency
before: 149.919 ± 0.168 M ops/s, 6.670 ns/op
after : 137.040 ± 0.187 M ops/s, 7.297 ns/op
nvme_configure_metadata() is issuing I/O, so we might incur an I/O
error which will cause the connection to be reset.
But in that case any further probing will race with reset and
cause UAF errors.
So return a status from nvme_configure_metadata() and abort
probing if there was an I/O error.
Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some error cases were not setting an auth-failure-reason-code-explanation.
This means an AUTH_Failure2 message will be sent with an explanation value
of 0 which is a reserved value.
Signed-off-by: Mark O'Donovan <shiftee@posteo.net> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In run_cache_set() after c->root returned from bch_btree_node_get(), it
is checked by IS_ERR_OR_NULL(). Indeed it is unncessary to check NULL
because bch_btree_node_get() will not return NULL pointer to caller.
This patch replaces IS_ERR_OR_NULL() by IS_ERR() for the above reason.
This patch adds code comments to bch_btree_node_get() and
__bch_btree_node_alloc() that NULL pointer will not be returned and it
is unnecessary to check NULL pointer by the callers of these routines.
Variable cur_idx is being initialized with a value that is never read,
it is being re-assigned later in a while-loop. Remove the redundant
assignment. Cleans up clang scan build warning:
drivers/md/bcache/writeback.c:916:2: warning: Value stored to 'cur_idx'
is never read [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Reviewed-by: Coly Li <colyli@suse.de> Signed-off-by: Coly Li <colyli@suse.de> Link: https://lore.kernel.org/r/20231120052503.6122-4-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Arraies bcache->stripe_sectors_dirty and bcache->full_dirty_stripes are
used for dirty data writeback, their sizes are decided by backing device
capacity and stripe size. Larger backing device capacity or smaller
stripe size make these two arraies occupies more dynamic memory space.
Currently bcache->stripe_size is directly inherited from
queue->limits.io_opt of underlying storage device. For normal hard
drives, its limits.io_opt is 0, and bcache sets the corresponding
stripe_size to 1TB (1<<31 sectors), it works fine 10+ years. But for
devices do declare value for queue->limits.io_opt, small stripe_size
(comparing to 1TB) becomes an issue for oversize memory allocations of
bcache->stripe_sectors_dirty and bcache->full_dirty_stripes, while the
capacity of hard drives gets much larger in recent decade.
For example a raid5 array assembled by three 20TB hardrives, the raid
device capacity is 40TB with typical 512KB limits.io_opt. After the math
calculation in bcache code, these two arraies will occupy 400MB dynamic
memory. Even worse Andrea Tomassetti reports that a 4KB limits.io_opt is
declared on a new 2TB hard drive, then these two arraies request 2GB and
512MB dynamic memory from kzalloc(). The result is that bcache device
always fails to initialize on his system.
To avoid the oversize memory allocation, bcache->stripe_size should not
directly inherited by queue->limits.io_opt from the underlying device.
This patch defines BCH_MIN_STRIPE_SZ (4MB) as minimal bcache stripe size
and set bcache device's stripe size against the declared limits.io_opt
value from the underlying storage device,
- If the declared limits.io_opt > BCH_MIN_STRIPE_SZ, bcache device will
set its stripe size directly by this limits.io_opt value.
- If the declared limits.io_opt < BCH_MIN_STRIPE_SZ, bcache device will
set its stripe size by a value multiplying limits.io_opt and euqal or
large than BCH_MIN_STRIPE_SZ.
Then the minimal stripe size of a bcache device will always be >= 4MB.
For a 40TB raid5 device with 512KB limits.io_opt, memory occupied by
bcache->stripe_sectors_dirty and bcache->full_dirty_stripes will be 50MB
in total. For a 2TB hard drive with 4KB limits.io_opt, memory occupied
by these two arraies will be 2.5MB in total.
Such mount of memory allocated for bcache->stripe_sectors_dirty and
bcache->full_dirty_stripes is reasonable for most of storage devices.
Reported-by: Andrea Tomassetti <andrea.tomassetti-opensource@devo.com> Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Eric Wheeler <bcache@lists.ewheeler.net> Link: https://lore.kernel.org/r/20231120052503.6122-2-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
blkcg_deactivate_policy() can be called after blkg_destroy_all()
returns, and it isn't necessary since blkg_destroy_all has covered
policy deactivation.
Inside blkg_for_each_descendant_pre(), both
css_for_each_descendant_pre() and blkg_lookup() requires RCU read lock,
and either cgroup_assert_mutex_or_rcu_locked() or rcu_read_lock_held()
is called.
Only present the DWMAC_LOONGSON option on architectures where it can
actually be used.
This follows the same logic as the DWMAC_INTEL option.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Cc: Keguang Zhang <keguang.zhang@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a device sends a packet that is inbetween 0
and sizeof(u64) the value passed to skb_trim()
as length will wrap around ending up as some very
large value.
The driver will then proceed to parse the header
located at that position, which will either oops or
process some random value.
The fix is to check against sizeof(u64) rather than
0, which the driver currently does. The issue exists
since the introduction of the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A Gen2 VM doesn't support legacy PCI/PCIe, so both raw_pci_ops and
raw_pci_ext_ops are NULL, and pci_subsys_init() -> pcibios_init()
doesn't call pcibios_resource_survey() -> e820__reserve_resources_late();
as a result, any emulated persistent memory of E820_TYPE_PRAM (12) via
the kernel parameter memmap=nn[KMG]!ss is not added into iomem_resource
and hence can't be detected by register_e820_pmem().
Fix this by directly calling e820__reserve_resources_late() in
hv_pci_init(), which is called from arch_initcall(pci_arch_init).
It's ok to move a Gen2 VM's e820__reserve_resources_late() from
subsys_initcall(pci_subsys_init) to arch_initcall(pci_arch_init) because
the code in-between doesn't depend on the E820 resources.
e820__reserve_resources_late() depends on e820__reserve_resources(),
which has been called earlier from setup_arch().
For a Gen-2 VM, the new hv_pci_init() also adds any memory of
E820_TYPE_PMEM (7) into iomem_resource, and acpi_nfit_register_region() ->
acpi_nfit_insert_resource() -> region_intersects() returns
REGION_INTERSECTS, so the memory of E820_TYPE_PMEM won't get added twice.
Changed the local variable "int gen2vm" to "bool gen2vm".
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <1699691867-9827-1-git-send-email-ssengar@linux.microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
MS confirm that "AISi" name of SMB2_CREATE_ALLOCATION_SIZE in MS-SMB2
specification is a typo. cifs/ksmbd have been using this wrong name from
MS-SMB2. It should be "AlSi". Also It will cause problem when running
smb2.create.open test in smbtorture against ksmbd.
Cc: stable@vger.kernel.org Fixes: 12197a7fdda9 ("Clarify SMB2/SMB3 create context and add missing ones") Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a partial revert of 8b3517f88ff2 ("PCI: loongson: Prevent LS7A MRRS
increases") for MIPS-based Loongson.
Some MIPS Loongson systems don't support arbitrary Max_Read_Request_Size
(MRRS) settings. 8b3517f88ff2 ("PCI: loongson: Prevent LS7A MRRS
increases") worked around that by (1) assuming that firmware configured
MRRS to the maximum supported value and (2) preventing the PCI core from
increasing MRRS.
Unfortunately, some firmware doesn't set that maximum MRRS correctly, which
results in devices not being initialized correctly. One symptom, from the
Debian report below, is this:
ata4.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6 frozen
ata4.00: failed command: WRITE FPDMA QUEUED
ata4.00: cmd 61/20:e8:00:f0:e1/00:00:00:00:00/40 tag 29 ncq dma 16384 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata4.00: status: { DRDY }
ata4: hard resetting link
Limit MRRS to 256 because MIPS Loongson with higher MRRS support is
considered rare.
This must be done at device enablement stage because the MRRS setting may
get lost if PCI_COMMAND_MASTER on the parent bridge is cleared, and we are
only sure parent bridge is enabled at this point.
cc22522fd55e ("PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root bus")
40613da52b13 fixed a problem where hot-adding a device with large BARs
failed if the bridge windows programmed by firmware were not large enough.
cc22522fd55e ("PCI: acpiphp: Use pci_assign_unassigned_bridge_resources()
only for non-root bus") fixed a problem with 40613da52b13: an ACPI hot-add
of a device on a PCI root bus (common in the virt world) or firmware
sending ACPI Bus Check to non-existent Root Ports (e.g., on Dell Inspiron
7352/0W6WV0) caused a NULL pointer dereference and suspend/resume hangs.
- Fiona reported that hot-add of SCSI disks in QEMU virtual machine fails
sometimes.
- Dongli reported a similar problem with hot-add of SCSI disks.
- Jonathan reported a console freeze during boot on bare metal due to an
error in radeon GPU initialization.
Revert both patches to avoid adding these problems. This means we will
again see the problems with hot-adding devices with large BARs and the NULL
pointer dereferences and suspend/resume issues that 40613da52b13 and cc22522fd55e were intended to fix.
Fixes: 40613da52b13 ("PCI: acpiphp: Reassign resources on bridge if necessary") Fixes: cc22522fd55e ("PCI: acpiphp: Use pci_assign_unassigned_bridge_resources() only for non-root bus") Reported-by: Fiona Ebner <f.ebner@proxmox.com> Closes: https://lore.kernel.org/r/9eb669c0-d8f2-431d-a700-6da13053ae54@proxmox.com Reported-by: Dongli Zhang <dongli.zhang@oracle.com> Closes: https://lore.kernel.org/r/3c4a446a-b167-11b8-f36f-d3c1b49b42e9@oracle.com Reported-by: Jonathan Woithe <jwoithe@just42.net> Closes: https://lore.kernel.org/r/ZXpaNCLiDM+Kv38H@marvin.atrad.com.au Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Igor Mammedov <imammedo@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HP laptop 15-db0403ng uses the ALC236 codec and controls the mute
LED using COEF 0x07 index 1.
Sound card subsystem: Hewlett-Packard Company Device [103c:84ae]
On ASUSTeK Z170M PLUS and Z170 PRO GAMING systems, the display codec
pins are not registered properly without the force-connect quirk. The
codec will report only one pin as having external connectivity, but i915
finds all three connectors on the system, so the two drivers are not
in sync.
Issue found with DRM igt-gpu-tools test kms_hdmi_inject@inject-audio.
Add one more older NUC model that requires quirk to force all pins to be
connected. The display codec pins are not registered properly without
the force-connect quirk. The codec will report only one pin as having
external connectivity, but i915 finds all three connectors on the
system, so the two drivers are not in sync.
Issue found with DRM igt-gpu-tools test kms_hdmi_inject@inject-audio.
fuse_dax_conn_free() will be called when fuse_fill_super_common() fails
after fuse_dax_conn_alloc(). Then deactivate_locked_super() in
virtio_fs_get_tree() will call virtio_kill_sb() to release the discarded
superblock. This will call fuse_dax_conn_free() again in fuse_conn_put(),
resulting in a possible double free.
Driver has a logic leak in ring data allocation/free,
where double free may happen in aq_ring_free if system is under
stress and driver init/deinit is happening.
The probability is higher to get this during suspend/resume cycle.
Verification was done simulating same conditions with
Because atalk_ioctl() accesses sk->sk_receive_queue
without holding a sk->sk_receive_queue.lock, it can
cause a race with atalk_recvmsg().
A use-after-free for skb occurs with the following flow.
```
atalk_ioctl() -> skb_peek()
atalk_recvmsg() -> skb_recv_datagram() -> skb_free_datagram()
```
Add sk->sk_receive_queue.lock to atalk_ioctl() to fix this issue.
Starting with commit 4e51bf44a03a ("net: bridge: move the switchdev
object replay helpers to "push" mode") the switchdev_bridge_port_offload()
helper was extended with the intention to provide switchdev drivers easy
access to object addition and deletion replays. This works by calling
the replay helpers with non-NULL notifier blocks.
In the same commit, the dpaa2-switch driver was updated so that it
passes valid notifier blocks to the helper. At that moment, no
regression was identified through testing.
In the meantime, the blamed commit changed the behavior in terms of
which ports get hit by the replay. Before this commit, only the initial
port which identified itself as offloaded through
switchdev_bridge_port_offload() got a replay of all port objects and
FDBs. After this, the newly joining port will trigger a replay of
objects on all bridge ports and on the bridge itself.
This behavior leads to errors in dpaa2_switch_port_vlans_add() when a
VLAN gets installed on the same interface multiple times.
The intended mechanism to address this is to pass a non-NULL ctx to the
switchdev_bridge_port_offload() helper and then check it against the
port's private structure. But since the driver does not have any use for
the replayed port objects and FDBs until it gains support for LAG
offload, it's better to fix the issue by reverting the dpaa2-switch
driver to not ask for replay. The pointers will be added back when we
are prepared to ignore replays on unrelated ports.
The size of the DMA unmap was wrongly put as a sizeof of a pointer.
Change the value of the DMA unmap to be the actual macro used for the
allocation and the DMA map.
There are some wrong return values check in sign-file when call OpenSSL
API. The ERR() check cond is wrong because of the program only check the
return value is < 0 which ignored the return val is 0. For example:
1. CMS_final() return 1 for success or 0 for failure.
2. i2d_CMS_bio_stream() returns 1 for success or 0 for failure.
3. i2d_TYPEbio() return 1 for success and 0 for failure.
4. BIO_free() return 1 for success and 0 for failure.
Link: https://www.openssl.org/docs/manmaster/man3/ Fixes: e5a2e3c84782 ("scripts/sign-file.c: Add support for signing with a raw signature") Signed-off-by: Yusong Gao <a869920004@gmail.com> Reviewed-by: Juerg Haefliger <juerg.haefliger@canonical.com> Signed-off-by: David Howells <dhowells@redhat.com> Link: https://lore.kernel.org/r/20231213024405.624692-1-a869920004@gmail.com/ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Generic code will use mdio. If it is not initialized before use,
the kernel will Oops.
Fixes: 30bba69d7db4 ("stmmac: pci: Add dwmac support for Loongson") Signed-off-by: Yanteng Si <siyanteng@loongson.cn> Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current xdp code drops packets larger than ENA_XDP_MAX_MTU.
This is an incorrect condition since the problem is not the
size of the packet, rather the number of buffers it contains.
This commit:
1. Identifies and drops XDP multi-buffer packets at the
beginning of the function.
2. Increases the xdp drop statistic when this drop occurs.
3. Adds a one-time print that such drops are happening to
give better indication to the user.
Fixes: 838c93dc5449 ("net: ena: implement XDP drop support") Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com> Signed-off-by: David Arinzon <darinzon@amazon.com> Link: https://lore.kernel.org/r/20231211062801.27891-3-darinzon@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ena_setup_and_create_all_xdp_queues() function freed all the
resources upon failure, after creating only xdp_num_queues queues,
instead of freeing just the created ones.
In this patch, the only resources that are freed, are the ones
allocated right before the failure occurs.
Fixes: 548c4940b9f1 ("net: ena: Implement XDP_TX action") Signed-off-by: Shahar Itzko <itzko@amazon.com> Signed-off-by: David Arinzon <darinzon@amazon.com> Link: https://lore.kernel.org/r/20231211062801.27891-2-darinzon@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
// TCP B: not send challenge ack for ack limit or packet loss
// TCP A: close
tcp_close
tcp_send_fin
if (!tskb && tcp_under_memory_pressure(sk))
tskb = skb_rb_last(&sk->tcp_rtx_queue); //pick SYN_ACK packet
TCP_SKB_CB(tskb)->tcp_flags |= TCPHDR_FIN; // set FIN flag
__tcp_retransmit_skb //skb->len=0
tcp_trim_head
len = tp->snd_una - TCP_SKB_CB(skb)->seq // len=101-100
__pskb_trim_head
skb->data_len -= len // skb->len=-1, wrap around
... ...
ip_fragment
icmp_glue_bits //BUG_ON
If we use tcp_trim_head() to remove acked SYN from packet that contains data
or other flags, skb->len will be incorrectly decremented. We can remove SYN
flag that has been acked from rtx_queue earlier than tcp_trim_head(), which
can fix the problem mentioned above.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Co-developed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com> Link: https://lore.kernel.org/r/20231210020200.1539875-1-dongchenchen2@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
qed_ilt_shadow_alloc() will call qed_ilt_shadow_free() to
free p_hwfn->p_cxt_mngr->ilt_shadow on error. However,
qed_cxt_tables_alloc() accesses the freed pointer on failure
of qed_ilt_shadow_alloc() through calling qed_cxt_mngr_free(),
which may lead to use-after-free. Fix this issue by setting
p_mngr->ilt_shadow to NULL in qed_ilt_shadow_free().
Fixes: fe56b9e6a8d9 ("qed: Add module with basic common support") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20231210045255.21383-1-dinghao.liu@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ntuple-filter feature on/off:
Default is on. If turned off, the filters will be removed from both
PF and iavf list. The removal is irrespective of current filter state.
Steps to reproduce:
-------------------
1. Ensure ntuple is on.
ethtool -K enp8s0 ntuple-filters on
2. Create a filter to receive the traffic into non-default rx-queue like 15
and ensure traffic is flowing into queue into 15.
Now, turn off ntuple. Traffic should not flow to configured queue 15.
It should flow to default RX queue.
Current FDIR state machines (SM) are not adequate to handle a few
scenarios in the link DOWN/UP event, reset event and ntuple-feature.
For example, when VF link goes DOWN and comes back UP administratively,
the expectation is that previously installed filters should also be
restored. But with current SM, filters are not restored.
So with new SM, during link DOWN filters are marked as INACTIVE in
the iavf list but removed from PF. After link UP, SM will transition
from INACTIVE to ADD_REQUEST to restore the filter.
Similarly, with VF reset, filters will be removed from the PF, but
marked as INACTIVE in the iavf list. Filters will be restored after
reset completion.
Steps to reproduce:
-------------------
1. Create a VF. Here VF is enp8s0.
2. Assign IP addresses to VF and link partner and ping continuously
from remote. Here remote IP is 1.1.1.1.
5. Ensure filter gets added and traffic is received on RX queue 15 now.
Link event testing:
-------------------
6. Bring VF link down and up. If traffic flows to configured queue 15,
test is success, otherwise it is a failure.
Reset event testing:
--------------------
7. Reset the VF. If traffic flows to configured queue 15, test is success,
otherwise it is a failure.
Because rose_ioctl() accesses sk->sk_receive_queue
without holding a sk->sk_receive_queue.lock, it can
cause a race with rose_accept().
A use-after-free for skb occurs with the following flow.
```
rose_ioctl() -> skb_peek()
rose_accept() -> skb_dequeue() -> kfree_skb()
```
Add sk->sk_receive_queue.lock to rose_ioctl() to fix this issue.
Because do_vcc_ioctl() accesses sk->sk_receive_queue
without holding a sk->sk_receive_queue.lock, it can
cause a race with vcc_recvmsg().
A use-after-free for skb occurs with the following flow.
```
do_vcc_ioctl() -> skb_peek()
vcc_recvmsg() -> skb_recv_datagram() -> skb_free_datagram()
```
Add sk->sk_receive_queue.lock to do_vcc_ioctl() to fix this issue.
Current implementation is such that, promisc mcam entry action
is set as multicast even when there are no trusted VFs. multicast
action causes the hardware to copy packet data, which reduces
the performance.
This patch fixes this issue by setting the promisc mcam entry action to
unicast instead of multicast when there are no trusted VFs. The same
change is made for the 'allmulti' mcam entry action.
Fixes: ffd2f89ad05c ("octeontx2-pf: Enable promisc/allmulti match MCAM entries.") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rvu_dl will be freed in rvu_nix_health_reporters_destroy(rvu_dl)
after the create_workqueue fails, and after that free, the rvu_dl will
be translate back through the following call chain:
Finally. in the err_dl_health label, rvu_dl being freed again in
rvu_health_reporters_destroy(rvu) by rvu_nix_health_reporters_destroy.
In the second calls of rvu_nix_health_reporters_destroy, however,
it uses rvu_dl->rvu_nix_health_reporter, which is already freed at
the end of rvu_nix_health_reporters_destroy in the first call.
So this patch prevents the first destroy by instantly returning -ENONMEN
when create_workqueue fails. In addition, since the failure of
create_workqueue is the only entrence of label err, it has been
integrated into the error-handling path of create_workqueue.
Fixes: 5ed66306eab6 ("octeontx2-af: Add devlink health reporters for NIX") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The old implementation extracted VLAN TCI info from the payload
before the VLAN tag has been pushed in the payload.
Another problem was that the VLAN TCI was extracted even if the
packet did not have VLAN protocol header.
This resulted in invalid VLAN TCI and as a consequence a random
queue was computed.
This patch fixes the above issues and use the VLAN TCI from the
skb if it is present or VLAN TCI from payload if present. If no
VLAN header is present queue 0 is selected.
Fixes: 52c4a1a85f4b ("net: fec: add ndo_select_queue to fix TX bandwidth fluctuations") Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com> Signed-off-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to skb_eth_hdr() introduced in commit 96cc4b69581d ("macvlan: do
not assume mac_header is set in macvlan_broadcast()"), let's introduce a
skb_vlan_eth_hdr() helper which can be used in TX-only code paths to get
to the VLAN header based on skb->data rather than based on the
skb_mac_header(skb).
We also consolidate the drivers that dereference skb->data to go through
this helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 9fc95fe95c3e ("net: fec: correct queue selection") Signed-off-by: Sasha Levin <sashal@kernel.org>
As &card->tx_queue_lock is acquired under softirq context along the
following call chain from solos_bh(), other acquisition of the same
lock inside process context should disable at least bh to avoid double
lock.
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
To prevent the potential deadlock, the patch uses spin_lock_bh()
on &card->tx_queue_lock under process context code consistently to
prevent the possible deadlock scenario.
Fixes: 213e85d38912 ("solos-pci: clean up pclose() function") Signed-off-by: Chengfeng Ye <dg573847474@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As &card->cli_queue_lock is acquired under softirq context along the
following call chain from solos_bh(), other acquisition of the same
lock inside process context should disable at least bh to avoid double
lock.
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
To prevent the potential deadlock, the patch uses spin_lock_bh()
on the card->cli_queue_lock under process context code consistently
to prevent the possible deadlock scenario.
Fixes: 9c54004ea717 ("atm: Driver for Solos PCI ADSL2+ card.") Signed-off-by: Chengfeng Ye <dg573847474@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the chip is configured to timestamp all receive packets, the
timestamp in the RX completion is only valid if the metadata
present flag is not set for packets received on the wire. In
addition, internal loopback packets will never have a valid timestamp
and the timestamp field will always be zero. We must exclude
any 0 value in the timestamp field because there is no way to
determine if it is a loopback packet or not.
Add a new function bnxt_rx_ts_valid() to check for all timestamp
valid conditions.
Fixes: 66ed81dcedc6 ("bnxt_en: Enable packet timestamping for all RX packets") Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20231208001658.14230-5-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The wait_event_interruptible_timeout() function returns 0
if the timeout elapsed, -ERESTARTSYS if it was interrupted
by a signal, and the remaining jiffies otherwise if the
condition evaluated to true before the timeout elapsed.
Driver should have checked for zero return value instead of
a positive value.
MChan: Print a warning for -ERESTARTSYS. The close operation
will proceed anyway when wait_event_interruptible_timeout()
returns for any reason. Since we do the close no matter what,
we should not return this error code to the caller. Change
bnxt_close_nic() to a void function and remove all error
handling from some of the callers.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.") Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Reviewed-by: Vikas Gupta <vikas.gupta@broadcom.com> Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20231208001658.14230-4-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the ring counters are stored in the per ring datastructure.
During reset, all the rings are freed together with the associated
datastructures. As a result, all the ring error counters will be reset
to zero.
Add logic to keep track of the total error counts of all the rings
and save them before reset (including ifdown). The next patch will
display these total ring error counters under ethtool -S.
We are issuing HWRM_FUNC_RESET cmd to reset the device including
all reserved resources, but not clearing the reservations
within the driver struct. As a result, when the driver re-initializes
as part of resume, it believes that there is no need to do any
resource reservation and goes ahead and tries to allocate rings
which will eventually fail beyond a certain number pre-reserved by
the firmware.
Fixes: 674f50a5b026 ("bnxt_en: Implement new method to reserve rings.") Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com> Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com> Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20231208001658.14230-2-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of a reset triggered by the QCA7000 itself, the behavior of the
qca_spi driver was not quite correct:
- in case of a pending RX frame decoding the drop counter must be
incremented and decoding state machine reseted
- also the reset counter must always be incremented regardless of sync
state
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Link: https://lore.kernel.org/r/20231206141222.52029-4-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reason for this is that the readonly setting rx_pending get
initialized and after that the range check in qcaspi_set_ringparam()
fails regardless of the provided parameter. So fix this by accepting
the exposed RX defaults. Instead of adding another magic number
better use a new define here.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Suggested-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Link: https://lore.kernel.org/r/20231206141222.52029-3-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The qca_spi driver stop and restart the SPI kernel thread
(via ndo_stop & ndo_open) in case of TX ring changes. This is
a big issue because it allows userspace to prevent restart of
the SPI kernel thread (via signals). A subsequent change of
TX ring wrongly assume a valid spi_thread pointer which result
in a crash.
So prevent this by stopping the network traffic handling and
temporary park the SPI thread.
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000") Signed-off-by: Stefan Wahren <wahrenst@gmx.net> Link: https://lore.kernel.org/r/20231206141222.52029-2-wahrenst@gmx.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Lorenzo points out that we effectively clear all unknown
flags from PIO when copying them to userspace in the netlink
RTM_NEWPREFIX notification.
We could fix this one at a time as new flags are defined,
or in one fell swoop - I choose the latter.
We could either define 6 new reserved flags (reserved1..6) and handle
them individually (and rename them as new flags are defined), or we
could simply copy the entire unmodified byte over - I choose the latter.
This unfortunately requires some anonymous union/struct magic,
so we add a static assert on the struct size for a little extra safety.
Cc: David Ahern <dsahern@kernel.org> Cc: Lorenzo Colitti <lorenzo@google.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Maciej Żenczykowski <maze@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to the cited patch, devlink health commands take devlink lock and
this may result in deadlock for mlx5e_tx_reporter as it takes local
state_lock before calling devlink health report and on the other hand
devlink health commands such as diagnose for same reporter take local
state_lock after taking devlink lock (see kernel log below).
To fix it, remove local state_lock from mlx5e_tx_timeout_work() before
calling devlink_health_report() and take care to cancel the work before
any call to close channels, which may free the SQs that should be
handled by the work. Before cancel_work_sync(), use current_work() to
check we are not calling it from within the work, as
mlx5e_tx_timeout_work() itself may close the channels and reopen as part
of recovery flow.
While removing state_lock from mlx5e_tx_timeout_work() keep rtnl_lock to
ensure no change in netdev->real_num_tx_queues, but use rtnl_trylock()
and a flag to avoid deadlock by calling cancel_work_sync() before
closing the channels while holding rtnl_lock too.
Kernel log:
======================================================
WARNING: possible circular locking dependency detected
6.0.0-rc3_for_upstream_debug_2022_08_30_13_10 #1 Not tainted
------------------------------------------------------
kworker/u16:2/65 is trying to acquire lock: ffff888122f6c2f8 (&devlink->lock_key#2){+.+.}-{3:3}, at: devlink_health_report+0x2f1/0x7e0
but task is already holding lock: ffff888121d20be0 (&priv->state_lock){+.+.}-{3:3}, at: mlx5e_tx_timeout_work+0x70/0x280 [mlx5_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Commit 46a0a2c96f0f ("HID: lenovo: Detect quirk-free fw on cptkbd and
stop applying workaround") introduced a regression for ThinkPad
TrackPoint Keyboard II which has similar quirks to cptkbd (so it uses
the same workarounds) but slightly different so that there are
false-positives during detecting well-behaving firmware. This commit
restricts detecting well-behaving firmware to the only model which
known to have one and have stable enough quirks to not cause
false-positives.
If an AFS cell that has an unreachable (eg. ENETUNREACH) server listed (VL
server or fileserver), an asynchronous probe to one of its addresses may
fail immediately because sendmsg() returns an error. When this happens, a
refcount underflow can happen if certain events hit a very small window.
The way this occurs is:
(1) There are two levels of "call" object, the afs_call and the
rxrpc_call. Each of them can be transitioned to a "completed" state
in the event of success or failure.
(2) Asynchronous afs_calls are self-referential whilst they are active to
prevent them from evaporating when they're not being processed. This
reference is disposed of when the afs_call is completed.
Note that an afs_call may only be completed once; once completed
completing it again will do nothing.
(3) When a call transmission is made, the app-side rxrpc code queues a Tx
buffer for the rxrpc I/O thread to transmit. The I/O thread invokes
sendmsg() to transmit it - and in the case of failure, it transitions
the rxrpc_call to the completed state.
(4) When an rxrpc_call is completed, the app layer is notified. In this
case, the app is kafs and it schedules a work item to process events
pertaining to an afs_call.
(5) When the afs_call event processor is run, it goes down through the
RPC-specific handler to afs_extract_data() to retrieve data from rxrpc
- and, in this case, it picks up the error from the rxrpc_call and
returns it.
The error is then propagated to the afs_call and that is completed
too. At this point the self-reference is released.
(6) If the rxrpc I/O thread manages to complete the rxrpc_call within the
window between rxrpc_send_data() queuing the request packet and
checking for call completion on the way out, then
rxrpc_kernel_send_data() will return the error from sendmsg() to the
app.
(7) Then afs_make_call() will see an error and will jump to the error
handling path which will attempt to clean up the afs_call.
(8) The problem comes when the error handling path in afs_make_call()
tries to unconditionally drop an async afs_call's self-reference.
This self-reference, however, may already have been dropped by
afs_extract_data() completing the afs_call
(9) The refcount underflows when we return to afs_do_probe_vlserver() and
that tries to drop its reference on the afs_call.
Fix this by making afs_make_call() attempt to complete the afs_call rather
than unconditionally putting it. That way, if afs_extract_data() manages
to complete the call first, afs_make_call() won't do anything.
The bug can be forced by making do_udp_sendmsg() return -ENETUNREACH and
sticking an msleep() in rxrpc_send_data() after the 'success:' label to
widen the race window.
projects / linux-stable / log