Ben reports that this should not have been backported to the older
kernels as the rest of the macro is not empty. It was a clean-up patch
in 6.4-rc1 only, it did not add new device ids.
This driver relies on IEEE80211_CONF_PS of hw->conf.flags to turn off PS or
turn on dynamic PS controlled by driver and firmware. Though this would be
incorrect, it did work before because the flag is always recalculated until
the commit 28977e790b5d ("wifi: mac80211: skip powersave recalc if driver SUPPORTS_DYNAMIC_PS")
is introduced by kernel 5.20 to skip to recalculate IEEE80211_CONF_PS
of hw->conf.flags if driver sets SUPPORTS_DYNAMIC_PS.
Correct this by doing recalculation while BSS_CHANGED_PS is changed and
interface is added or removed. It is allowed to enter PS only if single
one station vif is working. Without this fix, driver doesn't enter PS
anymore that causes higher power consumption.
This driver relies on IEEE80211_CONF_PS of hw->conf.flags to turn off PS or
turn on dynamic PS controlled by driver and firmware. Though this would be
incorrect, it did work before because the flag is always recalculated until
the commit 28977e790b5d ("wifi: mac80211: skip powersave recalc if driver SUPPORTS_DYNAMIC_PS")
is introduced by kernel 5.20 to skip to recalculate IEEE80211_CONF_PS
of hw->conf.flags if driver sets SUPPORTS_DYNAMIC_PS.
Correct this by doing recalculation while BSS_CHANGED_PS is changed and
interface is added or removed. For now, it is allowed to enter PS only if
single one station vif is working, and it could possible to have PS per
vif after firmware can support it. Without this fix, driver doesn't
enter PS anymore that causes higher power consumption.
ext4_xattr_block_set() relies on its caller to call dquot_initialize()
on the inode. To assure that this has happened there are WARN_ON
checks. Unfortunately, this is subject to false positives if there is
an antagonist thread which is flipping the file system at high rates
between r/o and rw. So only do the check if EXT4_XATTR_DEBUG is
enabled.
Commit 06149746e720 ("Bluetooth: hci_conn: Add support for linking
multiple hcon") reintroduced a previously fixed bug [1] ("KASAN:
slab-use-after-free Read in hci_conn_hash_flush"). This bug was
originally fixed by commit 5dc7d23e167e ("Bluetooth: hci_conn: Fix
possible UAF").
The hci_conn_unlink function was added to avoid invalidating the link
traversal caused by successive hci_conn_del operations releasing extra
connections. However, currently hci_conn_unlink itself also releases
extra connections, resulted in the reintroduced bug.
This patch follows a more robust solution for cleaning up all
connections, by repeatedly removing the first connection until there are
none left. This approach does not rely on the inner workings of
hci_conn_del and ensures proper cleanup of all connections.
Meanwhile, we need to make sure that hci_conn_del never fails. Indeed it
doesn't, as it now always returns zero. To make this a bit clearer, this
patch also changes its return type to void.
Reported-by: syzbot+8bb72f86fc823817bc5d@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-bluetooth/000000000000aa920505f60d25ad@google.com/ Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon") Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Co-developed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If hci_conn_put(conn->parent) reduces conn->parent's reference count to
zero, it can immediately deallocate conn->parent. At the same time,
conn->link->list has its head in conn->parent, causing use-after-free
problems in the latter list_del_rcu(&conn->link->list).
This problem can be easily solved by reordering the two operations,
i.e., first performing the list removal with list_del_rcu and then
decreasing the refcnt with hci_conn_put.
Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Closes: https://lore.kernel.org/linux-bluetooth/CABBYNZ+1kce8_RJrLNOXd_8=Mdpb=2bx4Nto-hFORk=qiOkoCg@mail.gmail.com/ Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon") Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hci_conn_unlink function is being called by hci_conn_del, which
means it should not call hci_conn_del with the input parameter conn
again. If it does, conn may have already been released when
hci_conn_unlink returns, leading to potential UAF and double-free
issues.
This patch resolves the problem by modifying hci_conn_unlink to release
only conn's child links when necessary, but never release conn itself.
Reported-by: syzbot+690b90b14f14f43f4688@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-bluetooth/000000000000484a8205faafe216@google.com/ Fixes: 06149746e720 ("Bluetooth: hci_conn: Add support for linking multiple hcon") Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Reported-by: syzbot+690b90b14f14f43f4688@syzkaller.appspotmail.com Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Reported-by: syzbot+8bb72f86fc823817bc5d@syzkaller.appspotmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The length field of netbios header must be greater than the SMB header
sizes(smb1 or smb2 header), otherwise the packet is an invalid SMB packet.
If `pdu_size` is 0, ksmbd allocates a 4 bytes chunk to `conn->request_buf`.
In the function `get_smb2_cmd_val` ksmbd will read cmd from
`rcv_hdr->Command`, which is `conn->request_buf + 12`, causing the KASAN
detector to print the following error message:
This bug is in parse_lease_state, and it is caused by the missing check
of `struct create_context`. When the ksmbd traverses the create_contexts,
it doesn't check if the field of `NameOffset` and `Next` is valid,
The KASAN message is following:
The check in the beginning is
`clen + sizeof(struct smb2_neg_context) <= len_of_ctxts`,
but in the end of loop, `len_of_ctxts` will subtract
`((clen + 7) & ~0x7) + sizeof(struct smb2_neg_context)`, which causes
integer underflow when clen does the 8 alignment. We should use
`(clen + 7) & ~0x7` in the check to avoid underflow from happening.
Then there are some variables that need to be declared unsigned
instead of signed.
Use the right structs for PACKED or split vqs when setting and
getting the vring base.
Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend") Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-4-shannon.nelson@amd.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use the right structs for PACKED or split vqs when setting and
getting the vring base.
Fixes: 4c8cf31885f6 ("vhost: introduce vDPA-based backend") Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Message-Id: <20230424225031.18947-3-shannon.nelson@amd.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the vdpa device is unregistered after the workqueue that
processes vq commands is disabled. However, the device unregister
process can still send commands to the cvq (a vlan delete for example)
which leads to a hang because the handing workqueue has been disabled
and the command never finishes:
The fix is to disable and destroy the workqueue after the device
unregister. It is expected that vhost will not trigger kicks after
the unregister. But even if it would, the wq is disabled already by
setting the pointer to NULL (done so in the referenced commit).
Fixes: ad6dc1daaf29 ("vdpa/mlx5: Avoid processing works if workqueue was destroyed") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Message-Id: <20230516095800.3549932-1-dtatulea@nvidia.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzkaller hits a kernel WARN when the first character of the dev name
provided is NULL. Solution is to add a NULL check before calling
cdev_device_add() in vduse_create_dev().
As riscv do not select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE,
the +0($arg2) addr is processed as a kernel address though it is a
userspace address, cause the above filename=(fault) print. So select
ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE to avoid the issue, after that the
kprobe trace is ok as below:
The current path that skips allocating the slave runtime does not clear
the alloc_slave_rt flag, this is clearly incorrect. Add the missing
clear, so the runtime won't be erroneously cleaned up.
Fixes: f3016b891c8c ("soundwire: stream: sdw_stream_add_ functions can be called multiple times") Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20230602101140.2040141-1-ckeepax@opensource.cirrus.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Selecting only REGMAP_I2C can leave REGMAP unset, causing build errors,
so also select REGMAP to prevent the build errors.
../drivers/misc/eeprom/at24.c:540:42: warning: 'struct regmap_config' declared inside parameter list will not be visible outside of this definition or declaration
540 | struct regmap_config *regmap_config)
../drivers/misc/eeprom/at24.c: In function 'at24_make_dummy_client':
../drivers/misc/eeprom/at24.c:552:18: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c:552:16: warning: assignment to 'struct regmap *' from 'int' makes pointer from integer without a cast [-Wint-conversion]
552 | regmap = devm_regmap_init_i2c(dummy_client, regmap_config);
../drivers/misc/eeprom/at24.c: In function 'at24_probe':
../drivers/misc/eeprom/at24.c:586:16: error: variable 'regmap_config' has initializer but incomplete type
586 | struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: error: storage size of 'regmap_config' isn't known
586 | struct regmap_config regmap_config = { };
../drivers/misc/eeprom/at24.c:586:30: warning: unused variable 'regmap_config' [-Wunused-variable]
Commit 8aeb7b17f04e ("RISC-V: Make mmap() with PROT_WRITE imply PROT_READ")
allows riscv to use mmap with PROT_WRITE only, and meanwhile mmap with w+x
is also permitted. However, when userspace tries to access this page with
PROT_WRITE|PROT_EXEC, which causes infinite loop at load page fault as
well as it triggers soft lockup. According to riscv privileged spec,
"Writable pages must also be marked readable". The fix to drop the
`PAGE_COPY_READ_EXEC` and then `PAGE_COPY_EXEC` would be just used instead.
This aligns the other arches (i.e arm64) for protection_map.
If pm runtime resume fails the .remove callback used to exit early. This
resulted in an error message by the driver core but the device gets
removed anyhow. This lets the registered i2c adapter stay around with an
unbound parent device.
So only skip clk disabling if resume failed, but do delete the adapter.
When constructing the sim, gpio-sim constructs an array of named lines,
sized based on the largest offset of any named line, and then initializes
that array with the names of all lines, including unnamed hogs with higher
offsets. In doing so it writes NULLs beyond the extent of the array.
Add a check that only named lines are used to initialize the array.
Fixes: cb8c474e79be ("gpio: sim: new testing module") Signed-off-by: Kent Gibson<warthog618@gmail.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As described in the commit 111a833dc5cb ("firmware: arm_ffa: Set
reserved/MBZ fields to zero in the memory descriptors") some fields in
the memory descriptor have to be zeroed explicitly. The handle field is
one of these, but it was left out from that change, fix this now.
Fixes: 111a833dc5cb ("firmware: arm_ffa: Set reserved/MBZ fields to zero in the memory descriptors") Reported-by: Imre Kis <imre.kis@arm.com> Signed-off-by: Balint Dobszay <balint.dobszay@arm.com> Link: https://lore.kernel.org/r/20230601140749.93812-1-balint.dobszay@arm.com Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There seems to be a bug within the mv64xxx I2C controller, wherein the
status register may not necessarily contain valid value immediately
after the IFLG flag is set in the control register.
My theory is that the controller:
- first sets the IFLG in control register
- then updates the status register
- then raises an interrupt
This may sometime cause weird bugs when in atomic mode, since in this
mode we do not wait for an interrupt, but instead we poll the control
register for IFLG and read status register immediately after.
I encountered -ENXIO from mv64xxx_i2c_fsm() due to this issue when using
this driver in atomic mode.
Note that I've only seen this issue on Armada 385, I don't know whether
other SOCs with this controller are also affected. Also note that this
fix has been in U-Boot for over 4 years [1] without anybody complaining,
so it should not cause regressions.
The final production baseboard had a different chip select than
earlier prototype boards. When the newer board was released,
the SPI stopped working because the wrong pin was used in the device
tree and conflicted with the UART RTS. Fix the pinmux for
production boards.
Fixes: 36ca3c8ccb53 ("arm64: dts: imx: Add Beacon i.MX8M Nano development kit") Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The nr_active counter continues to increase over time which causes the
blk_mq_get_tag to hang until the thread is rescheduled to a different
core despite there are still tags available.
kernel-stack
INFO: task inboundIOReacto:3014879 blocked for more than 2 seconds
Not tainted 6.1.15-amd64 #1 Debian 6.1.15~debian11
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:inboundIOReacto state:D stack:0 pid:3014879 ppid:4557 flags:0x00000000
Call Trace:
<TASK>
__schedule+0x351/0xa20
scheduler+0x5d/0xe0
io_schedule+0x42/0x70
blk_mq_get_tag+0x11a/0x2a0
? dequeue_task_stop+0x70/0x70
__blk_mq_alloc_requests+0x191/0x2e0
kprobe output showing RQF_MQ_INFLIGHT bit is not cleared before
__blk_mq_free_request being called.
The code in asoc_simple_startup was treating any non-zero return from
snd_pcm_hw_constraint_minmax as an error, when this can return 1 in some
normal cases and only negative values indicate an error.
When this happened, it caused asoc_simple_startup to disable the clocks
it just enabled and return 1, which was not treated as an error by the
calling code which only checks for negative return values. Then when the
PCM is eventually shut down, it causes the clock framework to complain
about disabling clocks that were not enabled.
Fix the check for snd_pcm_hw_constraint_minmax return value to only
treat negative values as an error.
Fixes: 5ca2ab459817 ("ASoC: simple-card-utils: Add new system-clock-fixed flag") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Link: https://lore.kernel.org/r/20230602011936.231931-1-robert.hancock@calian.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During mt8195_afe_init_clock(), mt8195_audsys_clk_register() was called
followed by several other devm functions. At mt8195_afe_deinit_clock()
located at mt8195_afe_pcm_dev_remove(), mt8195_audsys_clk_unregister()
was called.
However, there was an issue with the order in which these functions were
called. Specifically, the remove callback of platform_driver was called
before devres released the resource, resulting in a use-after-free issue
during remove time.
At probe time, the order of calls was:
1. mt8195_audsys_clk_register
2. afe_priv->clk = devm_kcalloc
3. afe_priv->clk[i] = devm_clk_get
At remove time, the order of calls was:
1. mt8195_audsys_clk_unregister
3. free afe_priv->clk[i]
2. free afe_priv->clk
To resolve the problem, we can utilize devm_add_action_or_reset() in
mt8195_audsys_clk_register() so that the remove order can be changed to
3->2->1.
Fixes: 6746cc858259 ("ASoC: mediatek: mt8195: add platform driver") Signed-off-by: Trevor Wu <trevor.wu@mediatek.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20230601033318.10408-3-trevor.wu@mediatek.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Acked-by: Takashi Iwai <tiwai@suse.de> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20230315150745.67084-114-u.kleine-koenig@pengutronix.de Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: dc93f0dcb436 ("ASoC: mediatek: mt8195: fix use-after-free in driver remove path") Signed-off-by: Sasha Levin <sashal@kernel.org>
During mt8188_afe_init_clock(), mt8188_audsys_clk_register() was called
followed by several other devm functions. The caller of
mt8188_afe_init_clock() utilized devm_add_action_or_reset() to call
mt8188_afe_deinit_clock(). However, the order was incorrect, causing a
use-after-free issue during remove time.
At probe time, the order of calls was:
1. mt8188_audsys_clk_register
2. afe_priv->clk = devm_kcalloc
3. afe_priv->clk[i] = devm_clk_get
At remove time, the order of calls was:
1. mt8188_audsys_clk_unregister
3. free afe_priv->clk[i]
2. free afe_priv->clk
To resolve the problem, it's necessary to move devm_add_action_or_reset()
to the appropriate position so that the remove order can be 3->2->1.
Fixes: f6b026479b13 ("ASoC: mediatek: mt8188: support audio clock control") Signed-off-by: Trevor Wu <trevor.wu@mediatek.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20230601033318.10408-2-trevor.wu@mediatek.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sending the mutex address(acp_lock) as platform
data during ACP PDM platform driver register sequence,
its creating copy of the platform data.
Referencing this platform data in ACP PDM driver results
incorrect reference to the common lock usage.
Instead of directly passing the lock address as platform
data, retrieve it from parent driver data structure
and use the same lock reference in ACP PDM driver.
Fixes: 45aa83cb9388 ("ASoC: amd: ps: use acp_lock to protect common registers in pdm driver") Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com> Link: https://lore.kernel.org/r/20230525113000.1290758-1-Vijendar.Mukunda@amd.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the assigned-clocks and assigned-clock-rates properties for the
LPUARTx nodes. Without these properties, the default clock rate
used would be 0, which can cause the UART ports to fail when open.
Fixes: 35f4e9d7530f ("arm64: dts: imx8: split adma ss into dma and audio ss") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In general, the three SKUs of sc7180 (lite, normal, and pro) are
handled dynamically.
The cpufreq table in sc7180.dtsi includes the superset of all CPU
frequencies. The "qcom-cpufreq-hw" driver in Linux shows that we can
dynamically detect which frequencies are actually available on the
currently running CPU and then we can just enable those ones.
The GPU is similarly dynamic. The nvmem has a fuse in it (see
"gpu_speed_bin" in sc7180.dtsi) that the GPU driver can use to figure
out which frequencies to enable.
There is one part, however, that is not so dynamic. The way SDRAM
frequency works in sc7180 is that it's tied to cpufreq. At the busiest
cpufreq operating points we'll pick the top supported SDRAM frequency.
They ramp down together.
For the "pro" SKU of sc7180, we only enable one extra cpufreq step.
That extra cpufreq step runs SDRAM at the same speed as the step
below. Thus, for normal and pro things are OK. There is no sc7180-pro
device tree snippet.
For the "lite" SKU if sc7180, however, things aren't so easy. The
"lite" SKU drops 3 cpufreq entries but can still run SDRAM at max
frequency. That messed things up with the whole scheme. This is why we
added the "sc7180-lite" fragment in commit 8fd01e01fd6f ("arm64: dts:
qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite").
When the lite scheme came about, it was agreed that the WiFi SKUs of
lazor would _always_ be "lite" and would, in fact, be the only "lite"
devices. Unfortunately, this decision changed and folks didn't realize
that it would be a problem. Specifically, some later lazor WiFi-only
devices were built with "pro" CPUs.
Building WiFi-only lazor with "pro" CPUs isn't the end of the world.
The SDRAM will ramp up a little sooner than it otherwise would, but
aside from a small power hit things work OK. One problem, though, is
that the SDRAM scaling becomes a bit quirky. Specifically, with the
current tables we'll max out SDRAM frequency at 2.1GHz but then
_lower_ it at 2.2GHz / 2.3GHz only to raise it back to max for 2.4GHz
and 2.55GHz.
Let's at least fix this so that the SDRAM frequency doesn't go down in
that quirky way. On true "lite" SKUs this change will be a no-op
because the operating points we're touching are disabled. This change
is only useful when a board that thinks it has a "lite" CPU actually
has a "normal" or "pro" one stuffed.
Fixes: 8fd01e01fd6f ("arm64: dts: qcom: sc7180-lite: Tweak DDR/L3 scaling on SC7180-lite") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230515171929.1.Ic8dee2cb79ce39ffc04eab2a344dde47b2f9459f@changeid Signed-off-by: Sasha Levin <sashal@kernel.org>
regmap-sdw does not support multi register writes, so there is
no point in setting this flag. This also leads to incorrect
programming of WSA codecs with regmap_multi_reg_write() call.
This invalid configuration should have been rejected by regmap-sdw.
regmap-sdw does not support multi register writes, so there is
no point in setting this flag. This also leads to incorrect
programming of WSA codecs with regmap_multi_reg_write() call.
This invalid configuration should have been rejected by regmap-sdw.
The of_find_device_by_node() function is returning a struct platform_device
object with the embedded struct device member's reference counter
incremented. This needs to be dropped when done with the platform device
returned by of_find_device_by_node().
at91_pm_eth_quirk_is_valid() calls of_find_device_by_node() on
suspend and resume path. On suspend it calls of_find_device_by_node() and
on resume and failure paths it drops the counter of
struct platform_device::dev.
In case ethernet device may not wakeup there is a put_device() on
at91_pm_eth_quirk_is_valid() which is wrong as it colides with
put_device() on resume path leading to the reference counter of struct
device embedded in struct platform_device to be messed, stack trace to be
displayed (after 5 consecutive suspend/resume cycles) and execution to
hang.
Along with this the error path of at91_pm_config_quirks() had been also
adapted to decrement propertly the reference counter of struct device
embedded in struct platform_device.
The rpmh driver will cache sleep and wake votes until the cluster
power-domain is about to enter idle, to avoid unnecessary writes. So
associate the apps_rsc with the cluster pd, so that it can be notified
about this event.
The current uses of PageAnon in page table check functions can lead to
type confusion bugs between struct page and slab [1], if slab pages are
accidentally mapped into the user space. This is because slab reuses the
bits in struct page to store its internal states, which renders PageAnon
ineffective on slab pages.
Since slab pages are not expected to be mapped into the user space, this
patch adds BUG_ON(PageSlab(page)) checks to make sure that slab pages
are not inadvertently mapped. Otherwise, there must be some bugs in the
kernel.
Without EXCLUSIVE_SYSTEM_RAM, users are allowed to map arbitrary
physical memory regions into the userspace via /dev/mem. At the same
time, pages may change their properties (e.g., from anonymous pages to
named pages) while they are still being mapped in the userspace, leading
to "corruption" detected by the page table check.
To avoid these false positives, this patch makes PAGE_TABLE_CHECK
depends on EXCLUSIVE_SYSTEM_RAM. This dependency is understandable
because PAGE_TABLE_CHECK is a hardening technique but /dev/mem without
STRICT_DEVMEM (i.e., !EXCLUSIVE_SYSTEM_RAM) is itself a security
problem.
Even with EXCLUSIVE_SYSTEM_RAM, I/O pages may be still allowed to be
mapped via /dev/mem. However, these pages are always considered as named
pages, so they won't break the logic used in the page table check.
When hcd->localmem_pool is non-null, localmem_pool is used to allocate
DMA memory. In this case, the dma address will be properly returned (in
dma_handle), and dma_mmap_coherent should be used to map this memory
into the user space. However, the current implementation uses
pfn_remap_range, which is supposed to map normal pages.
Instead of repeating the logic in the memory allocation function, this
patch introduces a more robust solution. Here, the type of allocated
memory is checked by testing whether dma_handle is properly set. If
dma_handle is properly returned, it means some DMA pages are allocated
and dma_mmap_coherent should be used to map them. Otherwise, normal
pages are allocated and pfn_remap_range should be called. This ensures
that the correct mmap functions are used consistently, independently
with logic details that determine which type of memory gets allocated.
The current implementation of usbdev_mmap uses usb_alloc_coherent to
allocate memory pages that will later be mapped into the user space.
Meanwhile, usb_alloc_coherent employs three different methods to
allocate memory, as outlined below:
* If hcd->localmem_pool is non-null, it uses gen_pool_dma_alloc to
allocate memory;
* If DMA is not available, it uses kmalloc to allocate memory;
* Otherwise, it uses dma_alloc_coherent.
However, it should be noted that gen_pool_dma_alloc does not guarantee
that the resulting memory will be page-aligned. Furthermore, trying to
map slab pages (i.e., memory allocated by kmalloc) into the user space
is not resonable and can lead to problems, such as a type confusion bug
when PAGE_TABLE_CHECK=y [1].
To address these issues, this patch introduces hcd_alloc_coherent_pages,
which addresses the above two problems. Specifically,
hcd_alloc_coherent_pages uses gen_pool_dma_alloc_align instead of
gen_pool_dma_alloc to ensure that the memory is page-aligned. To replace
kmalloc, hcd_alloc_coherent_pages directly allocates pages by calling
__get_free_pages.
Reported-by: syzbot+fcf1a817ceb50935ce99@syzkaller.appspotmail.comm Closes: https://lore.kernel.org/lkml/000000000000258e5e05fae79fc1@google.com/ [1] Fixes: f7d34b445abc ("USB: Add support for usbfs zerocopy.") Fixes: ff2437befd8f ("usb: host: Fix excessive alignment restriction for local memory allocations") Cc: stable@vger.kernel.org Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20230515130958.32471-2-lrh2000@pku.edu.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass to dev_err_probe() PTR_ERR from actual dev_pm_opp_find_bw_floor()
call which failed, instead of previous ret which at this point is 0.
Failure of dev_pm_opp_find_bw_floor() would result in prematurely ending
the probe with success.
Fixes smatch warnings:
drivers/soc/qcom/icc-bwmon.c:776 bwmon_probe() warn: passing zero to 'dev_err_probe'
drivers/soc/qcom/icc-bwmon.c:781 bwmon_probe() warn: passing zero to 'dev_err_probe'
Commit 699b045a8e43 ("net: virtio_net: notifications coalescing
support") added coalescing command support for virtio_net. However,
the coalesce commands are using buffers on the stack, which is causing
the device to see DMA errors. There should also be a complaint from
check_for_stack() in debug_dma_map_xyz(). Fix this by adding and using
coalesce params from the control_buf struct, which aligns with other
commands.
Cc: stable@vger.kernel.org Fixes: 699b045a8e43 ("net: virtio_net: notifications coalescing support") Reviewed-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: Allen Hubbe <allen.hubbe@amd.com> Signed-off-by: Brett Creeley <brett.creeley@amd.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20230605195925.51625-1-brett.creeley@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move capturing the snapshot context into the image request state
machine, after exclusive lock is ensured to be held for the duration of
dealing with the image request. This is needed to ensure correctness
of fast-diff states (OBJECT_EXISTS vs OBJECT_EXISTS_CLEAN) and object
deltas computed based off of them. Otherwise the object map that is
forked for the snapshot isn't guaranteed to accurately reflect the
contents of the snapshot when the snapshot is taken under I/O. This
breaks differential backup and snapshot-based mirroring use cases with
fast-diff enabled: since some object deltas may be incomplete, the
destination image may get corrupted.
Move RBD_OBJ_FLAG_COPYUP_ENABLED flag setting into the object request
state machine to allow for the snapshot context to be captured in the
image request state machine rather than in rbd_queue_workfn().
After TEE has completed processing of TEE_CMD_ID_LOAD_TA, set proper
value in 'return_origin' argument passed by open_session() call. To do
so, add 'return_origin' field to the structure tee_cmd_load_ta. The
Trusted OS shall update return_origin as part of TEE processing.
This change to 'struct tee_cmd_load_ta' interface requires a similar update
in AMD-TEE Trusted OS's TEE_CMD_ID_LOAD_TA interface.
This patch has been verified on Phoenix Birman setup. On older APUs,
return_origin value will be 0.
Since commit 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support
during hci down for wcn3990"), the setup callback which registers the
debugfs interface can be called multiple times.
This specifically leads to the following error when powering on the
controller:
debugfs: Directory 'ibs' with parent 'hci0' already present!
Add a driver flag to avoid trying to register the debugfs interface more
than once.
Fixes: 3e4be65eb82c ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990") Cc: stable@vger.kernel.org # 4.20 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit ec6cef9cd98d ("Bluetooth: Fix SMP channel registration for
unconfigured controllers") the debugfs interface for unconfigured
controllers will be created when the controller is configured.
There is however currently nothing preventing a controller from being
configured multiple time (e.g. setting the device address using btmgmt)
which results in failed attempts to register the already registered
debugfs entries:
debugfs: File 'features' in directory 'hci0' already present!
debugfs: File 'manufacturer' in directory 'hci0' already present!
debugfs: File 'hci_version' in directory 'hci0' already present!
...
debugfs: File 'quirk_simultaneous_discovery' in directory 'hci0' already present!
Add a controller flag to avoid trying to register the debugfs interface
more than once.
Fixes: ec6cef9cd98d ("Bluetooth: Fix SMP channel registration for unconfigured controllers") Cc: stable@vger.kernel.org # 4.0 Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit 0f7d9b31ce7a ("netfilter: nf_tables: fix use-after-free
in nft_set_catchall_destroy()"). We can not access k after kfree_rcu()
call.
Cc: stable@vger.kernel.org Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lock around counting the channel queue length in the BIODASDINFO
ioctl was incorrectly changed to the dasd_block->queue_lock with commit 583d6535cb9d ("dasd: remove dead code"). This can lead to endless list
iterations and a subsequent crash.
The queue_lock is supposed to be used only for queue lists belonging to
dasd_block. For dasd_device related queue lists the ccwdev lock must be
used.
Fix the mentioned issues by correctly using the ccwdev lock instead of
the queue lock.
Fixes: 583d6535cb9d ("dasd: remove dead code") Cc: stable@vger.kernel.org # v5.0+ Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com> Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Link: https://lore.kernel.org/r/20230609153750.1258763-2-sth@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Turning off the PLL and entering D0i3 will reset the VPU so
an explicit IP reset is redundant.
But if the VPU is active, it may interfere with PLL disabling
and to avoid that, we have to issue an additional IP reset
to silence the VPU before turning off the PLL.
Fixes: a8fed6d1e0b9 ("accel/ivpu: Fix power down sequence") Cc: stable@vger.kernel.org # 6.3.x Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com> Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com> Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230525103818.877590-1-stanislaw.gruszka@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between capsnaps flush and removing the inode from
'mdsc->snap_flush_list' list:
== Thread A == == Thread B ==
ceph_queue_cap_snap()
-> allocate 'capsnapA'
->ihold('&ci->vfs_inode')
->add 'capsnapA' to 'ci->i_cap_snaps'
->add 'ci' to 'mdsc->snap_flush_list'
...
== Thread C ==
ceph_flush_snaps()
->__ceph_flush_snaps()
->__send_flush_snap()
handle_cap_flushsnap_ack()
->iput('&ci->vfs_inode')
this also will release 'ci'
...
== Thread D ==
ceph_handle_snap()
->flush_snaps()
->iterate 'mdsc->snap_flush_list'
->get the stale 'ci'
->remove 'ci' from ->ihold(&ci->vfs_inode) this
'mdsc->snap_flush_list' will WARNING
To fix this we will increase the inode's i_count ref when adding 'ci'
to the 'mdsc->snap_flush_list' list.
To align with what is done by the in-kernel PM, update userspace pm
subflow selftests, by sending the a remove_addrs command together
before the remove_subflows command. This will get a RM_ADDR in
chk_rm_nr().
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE") Fixes: 5e986ec46874 ("selftests: mptcp: userspace pm subflow tests") Link: https://github.com/multipath-tcp/mptcp_net-next/issues/379 Cc: stable@vger.kernel.org Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is linked to the previous commit ("mptcp: only send RM_ADDR in
nl_cmd_remove").
To align with what is done by the in-kernel PM, update userspace pm addr
selftests, by sending a remove_subflows command together after the
remove_addrs command.
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE") Fixes: 97040cf9806e ("selftests: mptcp: userspace pm address tests") Cc: stable@vger.kernel.org Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase pm subflows counter on both server side and client side when
userspace pm creates a new subflow, and decrease the counter when it
closes a subflow.
Increase add_addr_signaled counter in mptcp_nl_cmd_announce() when the
address is announced by userspace PM.
This modification is similar to how the in-kernel PM is updating the
counter: when additional subflows are created/removed.
Fixes: 9ab4807c84a4 ("mptcp: netlink: Add MPTCP_PM_CMD_ANNOUNCE") Fixes: 702c2f646d42 ("mptcp: netlink: allow userspace-driven subflow establishment") Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/329 Cc: stable@vger.kernel.org Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the address into userspace_pm_local_addr_list when the subflow is
created. Make sure it can be found in mptcp_nl_cmd_remove(). And delete
it in the new helper mptcp_userspace_pm_delete_local_addr().
By doing this, the "REMOVE" command also works with subflows that have
been created via the "SUB_CREATE" command instead of restricting to
the addresses that have been announced via the "ANNOUNCE" command.
Fixes: d9a4594edabf ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE") Link: https://github.com/multipath-tcp/mptcp_net-next/issues/379 Cc: stable@vger.kernel.org Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Mat Martineau <martineau@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: use-after-free in kref_put include/linux/kref.h:64 [inline]
BUG: KASAN: use-after-free in j1939_priv_put+0x25/0xa0 net/can/j1939/main.c:172
Write of size 4 at addr ffff888141c15058 by task swapper/3/0
To avoid this, call j1939_can_rx_register() under j1939_netdev_lock so
that a concurrent thread cannot process j1939_priv before
j1939_can_rx_register() returns.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
It turns out access to j1939_can_rx_register() needs to be serialized,
otherwise j1939_priv can be corrupted when parallel threads call
j1939_netdev_start() and j1939_can_rx_register() fails. This issue is
thoroughly covered in other commit which serializes access to
j1939_can_rx_register().
Change j1939_netdev_lock type to mutex so that we do not need to remove
GFP_KERNEL from can_rx_register().
j1939_netdev_lock seems to be used in normal contexts where mutex usage
is not prohibited.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
This patch addresses an issue within the j1939_sk_send_loop_abort()
function in the j1939/socket.c file, specifically in the context of
Transport Protocol (TP) sessions.
Without this patch, when a TP session is initiated and a Clear To Send
(CTS) frame is received from the remote side requesting one data packet,
the kernel dispatches the first Data Transport (DT) frame and then waits
for the next CTS. If the remote side doesn't respond with another CTS,
the kernel aborts due to a timeout. This leads to the user-space
receiving an EPOLLERR on the socket, and the socket becomes active.
However, when trying to read the error queue from the socket with
sock.recvmsg(, , socket.MSG_ERRQUEUE), it returns -EAGAIN,
given that the socket is non-blocking. This situation results in an
infinite loop: the user-space repeatedly calls epoll(), epoll() returns
the socket file descriptor with EPOLLERR, but the socket then blocks on
the recv() of ERRQUEUE.
This patch introduces an additional check for the J1939_SOCK_ERRQUEUE
flag within the j1939_sk_send_loop_abort() function. If the flag is set,
it indicates that the application has subscribed to receive error queue
messages. In such cases, the kernel can communicate the current transfer
state via the error queue. This allows for the function to return early,
preventing the unnecessary setting of the socket into an error state,
and breaking the infinite loop. It is crucial to note that a socket
error is only needed if the application isn't using the error queue, as,
without it, the application wouldn't be aware of transfer issues.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Reported-by: David Jander <david@protonic.nl> Tested-by: David Jander <david@protonic.nl> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/r/20230526081946.715190-1-o.rempel@pengutronix.de Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmemdup() at line 2735 is not duplicating enough memory for
notif->tid_tear_down and notif->station_id. As it only duplicates
612 bytes: up to offsetofend(struct iwl_wowlan_info_notif,
received_beacons), this is the range of [0, 612) bytes.
Fix this by allocating space for the whole notif object and zero out the
remaining space in memory after member station_id.
This also fixes the following -Warray-bounds issues:
CC drivers/net/wireless/intel/iwlwifi/mvm/d3.o
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function ‘iwl_mvm_wait_d3_notif’:
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2743:30: warning: array subscript ‘struct iwl_wowlan_info_notif[0]’ is partly outside array bounds of ‘unsigned char[612]’ [-Warray-bounds=]
2743 | notif->tid_tear_down = notif_v1->tid_tear_down;
|
from drivers/net/wireless/intel/iwlwifi/mvm/d3.c:7:
In function ‘kmemdup’,
inlined from ‘iwl_mvm_wait_d3_notif’ at drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2735:12:
include/linux/fortify-string.h:765:16: note: object of size 612 allocated by ‘__real_kmemdup’
765 | return __real_kmemdup(p, size, gfp);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/intel/iwlwifi/mvm/d3.c: In function ‘iwl_mvm_wait_d3_notif’:
drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2744:30: warning: array subscript ‘struct iwl_wowlan_info_notif[0]’ is partly outside array bounds of ‘unsigned char[612]’ [-Warray-bounds=]
2744 | notif->station_id = notif_v1->station_id;
| ^~
In function ‘kmemdup’,
inlined from ‘iwl_mvm_wait_d3_notif’ at drivers/net/wireless/intel/iwlwifi/mvm/d3.c:2735:12:
include/linux/fortify-string.h:765:16: note: object of size 612 allocated by ‘__real_kmemdup’
765 | return __real_kmemdup(p, size, gfp);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Link: https://github.com/KSPP/linux/issues/306 Fixes: 905d50ddbc83 ("wifi: iwlwifi: mvm: support wowlan info notification version 2") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Acked-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/ZHpGN555FwAKGduH@work Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
When going from ODM 2:1 single display case to max displays, second
odm pipe needs to be repurposed for one of the new single displays.
However, acquire_first_split_pipe() only handles MPC case and not
ODM case
[How]
Add ODM conditions in acquire_first_split_pipe()
Add commit_minimal_transition_state() in commit_streams() to handle
odm 2:1 exit first, and then process new streams
Handle ODM condition in commit_minimal_transition_state()
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Acked-by: Stylon Wang <stylon.wang@amd.com> Signed-off-by: Samson Tam <samson.tam@amd.com> Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf488dcd0ab7 ("drm/amd: Allow s0ix without BIOS support") showed
improvements to power consumption over suspend when s0ix wasn't enabled in
BIOS and the system didn't support S3.
This patch however was misguided because the reason the system didn't
support S3 was because SMT was disabled in OEM BIOS setup.
This prevented the BIOS from allowing S3.
Also allowing GPUs to use the s2idle path actually causes problems if
they're invoked on systems that may not support s2idle in the platform
firmware. `systemd` has a tendency to try to use `s2idle` if `deep` fails
for any reason, which could lead to unexpected flows.
The original commit also fixed a problem during resume from suspend to idle
without hardware support, but this is no longer necessary with commit ca4751866397 ("drm/amd: Don't allow s0ix on APUs older than Raven")
Revert commit cf488dcd0ab7 ("drm/amd: Allow s0ix without BIOS support")
to make it match the expected behavior again.
Cc: Rafael Ávila de Espíndola <rafael@espindo.la> Link: https://github.com/torvalds/linux/blob/v6.1/drivers/gpu/drm/amd/amdgpu/amdgpu_acpi.c#L1060 Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/2599 Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Alex, most APUs from that time seem to have the same issue
(vbios says 48Mhz, actual is 100Mhz). I only have a CHIP_STONEY so I
limit the fixup to CHIP_STONEY
cmipci driver replaces the kctl->id.device after assigning the kctl
via snd_ctl_add(). This doesn't work any longer with the new Xarray
lookup change. It has to be set before snd_ctl_add() call instead.
Fixes: c27e1efb61c5 ("ALSA: control: Use xarray for faster lookups") Cc: <stable@vger.kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20230606093855.14685-3-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GUS driver replaces the kctl->id.index after assigning the kctl via
snd_ctl_add(). This doesn't work any longer with the new Xarray
lookup change. It has to be set before snd_ctl_add() call instead.
Fixes: c27e1efb61c5 ("ALSA: control: Use xarray for faster lookups") Cc: <stable@vger.kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20230606093855.14685-4-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ymfpci driver replaces the kctl->id.device after assigning the kctl
via snd_ctl_add(). This doesn't work any longer with the new Xarray
lookup change. It has to be set before snd_ctl_add() call instead.
Fixes: c27e1efb61c5 ("ALSA: control: Use xarray for faster lookups") Cc: <stable@vger.kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20230606093855.14685-2-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HD-audio core code replaces the kctl->id.index of SPDIF-related
controls after assigning via snd_ctl_add(). This doesn't work any
longer with the new Xarray lookup change. The change of the kctl->id
content has to be done via snd_ctl_rename_id() helper, instead.
Fixes: c27e1efb61c5 ("ALSA: control: Use xarray for faster lookups") Cc: <stable@vger.kernel.org> Reviewed-by: Jaroslav Kysela <perex@perex.cz> Link: https://lore.kernel.org/r/20230606093855.14685-5-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the kernel increments device's open count in input_open_device()
even if device is inhibited, the counter should always be decremented in
input_close_device() to keep it balanced.
While doing my research to improve the xpad device names I noticed
that the 1532:0037 VID/PID seems to be used by the DeathAdder 2013,
so that Razer Sabertooth instance looked wrong and very suspect to
me. I didn't see any mention in the official drivers, either.
After doing more research, it turns out that the xpad list
is used by many other projects (like Steam) as-is [1], this
issue was reported [2] and Valve/Sam Lantinga fixed it [3]:
(With multiple Internet users reporting similar issues, not linked here)
After not being able to find the correct VID/PID combination anywhere
on the Internet and not receiving any reply from Razer support I did
some additional detective work, it seems like it presents itself as
"Razer Sabertooth Gaming Controller (XBOX360)", code 1689:FE00.
Leaving us with this:
* Razer Sabertooth (1689:fe00)
* Razer Sabertooth Elite (24c6:5d04)
* Razer DeathAdder 2013 (1532:0037) [note: not a gamepad]
So, to sum things up; remove this conflicting/duplicate entry:
As the real/correct one is already present there, even if
the Internet as a whole insists on presenting it as the
Razer Sabertooth Elite, which (by all accounts) is not:
Syzkaller got a lot of crashes like:
KASAN: use-after-free Write in *_timers*
All of these crashes point to the same memory area:
The buggy address belongs to the object at ffff88801f870000
which belongs to the cache kmalloc-8k of size 8192
The buggy address is located 5320 bytes inside of
8192-byte region [ffff88801f870000, ffff88801f872000)
This area belongs to :
batadv_priv->batadv_priv_dat->delayed_work->timer_list
The reason for these issues is the lack of synchronization. Delayed
work (batadv_dat_purge) schedules new timer/work while the device
is being deleted. As the result new timer/delayed work is set after
cancel_delayed_work_sync() was called. So after the device is freed
the timer list contains pointer to already freed memory.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Cc: stable@kernel.org Fixes: 2f1dfbe18507 ("batman-adv: Distributed ARP Table - implement local storage") Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru> Acked-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move GMU mutex initialization earlier to make sure that it is always
initialized. a6xx_destroy can be called from ther failure path before
GMU initialization.
Fixes: 4cd15a3e8b36 ("drm/msm/a6xx: Make GPU destroy a bit safer") Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/531540/ Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As per the new udp tunnel framework, drivers which need to know the
details of a port entry (i.e. port type) when it gets deleted should
use the .set_port / .unset_port callbacks.
Implementing the current .udp_tunnel_sync callback would mean that the
deleted tunnel port entry would be all zeros. This used to work on
older firmware because it would not check the input when deleting a
tunnel port. With newer firmware, the delete will now fail and
subsequent tunnel port allocation will fail as a result.
Fixes: 442a35a5a7aa ("bnxt: convert to new udp_tunnel_nic infra") Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The firmware can send PHC_RTC_UPDATE async event on a PF that may not
have PTP registered. In such a case, there will be a null pointer
deference for bp->ptp_cfg when we try to handle the event.
Fix it by not registering for this event with the firmware if !bp->ptp_cfg.
Also, check that bp->ptp_cfg is valid before proceeding when we receive
the event.
Fixes: 8bcf6f04d4a5 ("bnxt_en: Handle async event when the PHC is updated in RTC mode") Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver starts firmware fatal error recovery by detecting
heartbeat failure or fw reset count register changing. But
these checks are not reliable if the device is not accessible.
This can happen while DPC (Downstream Port containment) is in
progress. Skip firmware fatal recovery if pci_device_is_present()
returns false.
We need to call bnxt_hwrm_func_qcfg() on a VF to query the default
VLAN that may be setup by the PF. If a default VLAN is enabled,
the VF cannot support VLAN acceleration on the receive side and
the VNIC must be setup to strip out the default VLAN tag. If a
default VLAN is not enabled, the VF can support VLAN acceleration
on the receive side. The VNIC should be set up to strip or not
strip the VLAN based on the RX VLAN acceleration setting.
Without this call to determine the default VLAN before calling
bnxt_setup_vnic(), the VNIC may not be set up correctly. For
example, bnxt_setup_vnic() may set up to strip the VLAN tag based
on stale default VLAN information. If RX VLAN acceleration is
not enabled, the VLAN tag will be incorrectly stripped and the
RX data path will not work correctly.
Fixes: cf6645f8ebc6 ("bnxt_en: Add function for VF driver to query default VLAN.") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only older NIC controller's firmware uses the PROC AP reset type.
Firmware on 5731X/5741X and newer chips does not support this reset
type. When bnxt_reset() issues a series of resets, this PROC AP
reset may actually fail on these newer chips because the firmware
is not ready to accept this unsupported command yet. Avoid this
unnecessary error by skipping this reset type on chips that don't
support it.
Fixes: 7a13240e3718 ("bnxt_en: fix ethtool_reset_flags ABI violations") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log