The ACPI device CSC3556 is a Cirrus Logic CS35L56 mono amplifier which
is used in multiples, and can be connected either to I2C or SPI.
There will be multiple instances under the same Device() node. Add it
to ignore_serial_bus_ids and handle it in the serial-multi-instantiate
driver.
There can be a 5th I2cSerialBusV2, but this is an alias address and doesn't
represent a real device. Ignore this by having a dummy 5th entry in the
serial-multi-instantiate instance list with the name of a non-existent
driver, on the same pattern as done for bsg2150.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com> Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Link: https://lore.kernel.org/r/20230728111345.7224-1-rf@opensource.cirrus.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code assumes that the CSC3551(multiple cs35l41) always have
its interrupt pin connected to GPIO thus the IRQ can be acquired with
acpi_dev_gpio_irq_get. However on some newer laptop models this is no
longer the case as they have the CSC3551's interrupt pin connected to
APIC. This causes smi_i2c_probe to fail on these machines.
To support these machines, a new macro IRQ_RESOURCE_AUTO was introduced
for cs35l41 smi_node, and smi_get_irq function was modified so it tries
to get GPIO irq resource first and if failed, tries to get
APIC irq resource for cs35l41.
This patch affects only the cs35l41's probing and brings no negative
influence on machines that indeed have the cs35l41's interrupt pin
connected to GPIO.
Use kernel_power_off() instead of kernel_halt() to pass through
machine_power_off() -> pm_power_off(), otherwise axillary power does
not go off.
Change "power down" bitmask.
Fixes: dd635e33b5c9 ("platform: mellanox: Introduce support of new Nvidia L1 switch") Signed-off-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Michael Shych <michaelsh@nvidia.com> Link: https://lore.kernel.org/r/20230813083735.39090-4-vadimp@nvidia.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change polarity of chassis health and power signals and fix latch reset
mask for L1 switch.
Fixes: dd635e33b5c9 ("platform: mellanox: Introduce support of new Nvidia L1 switch") Signed-off-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Michael Shych <michaelsh@nvidia.com> Link: https://lore.kernel.org/r/20230813083735.39090-3-vadimp@nvidia.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move debug register offsets to different location due to hardware changes.
Fixes: dd635e33b5c9 ("platform: mellanox: Introduce support of new Nvidia L1 switch") Signed-off-by: Vadim Pasternak <vadimp@nvidia.com> Reviewed-by: Michael Shych <michaelsh@nvidia.com> Link: https://lore.kernel.org/r/20230813083735.39090-5-vadimp@nvidia.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The lenovo-ymc driver is causing the keyboard + touchpad to stop working
on some regular laptop models such as the Lenovo ThinkBook 13s G2 ITL 20V9.
The problem is that there are YMC WMI GUID methods in the ACPI tables
of these laptops, despite them not being Yogas and lenovo-ymc loading
causes libinput to see a SW_TABLET_MODE switch with state 1.
This in turn causes libinput to ignore events from the builtin keyboard
and touchpad, since it filters those out for a Yoga in tablet mode.
Similar issues with false-positive SW_TABLET_MODE=1 reporting have
been seen with the intel-hid driver.
Copy the intel-hid driver approach to fix this and only bind to the WMI
device on machines where the DMI chassis-type indicates the machine
is a convertible.
Add a 'force' module parameter to allow overriding the chassis-type check
so that users can easily test if the YMC interface works on models which
report an unexpected chassis-type.
Fixes: e82882cdd241 ("platform/x86: Add driver for Yoga Tablet Mode switch") Link: https://bugzilla.redhat.com/show_bug.cgi?id=2229373 Cc: André Apitzsch <git@apitzsch.eu> Cc: stable@vger.kernel.org Tested-by: Andrew Kallmeyer <kallmeyeras@gmail.com> Tested-by: Gergő Köteles <soyer@irl.hu> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230812144818.383230-1-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The msi-ec driver fails to build for me (gcc 7.5):
CC [M] drivers/platform/x86/msi-ec.o
drivers/platform/x86/msi-ec.c:72:6: error: initializer element is not constant
{ SM_ECO_NAME, 0xc2 },
^~~~~~~~~~~
drivers/platform/x86/msi-ec.c:72:6: note: (near initialization for ‘CONF0.shift_mode.modes[0].name’)
drivers/platform/x86/msi-ec.c:73:6: error: initializer element is not constant
{ SM_COMFORT_NAME, 0xc1 },
^~~~~~~~~~~~~~~
drivers/platform/x86/msi-ec.c:73:6: note: (near initialization for ‘CONF0.shift_mode.modes[1].name’)
drivers/platform/x86/msi-ec.c:74:6: error: initializer element is not constant
{ SM_SPORT_NAME, 0xc0 },
^~~~~~~~~~~~~
drivers/platform/x86/msi-ec.c:74:6: note: (near initialization for ‘CONF0.shift_mode.modes[2].name’)
(...)
Don't try to be smart, just use defines for the constant strings. The
compiler will recognize it's the same string and will store it only
once in the data section anyway.
Signed-off-by: Jean Delvare <jdelvare@suse.de> Fixes: 392cacf2aa10 ("platform/x86: Add new msi-ec driver") Cc: stable@vger.kernel.org Cc: Nikita Kravets <teackot@gmail.com> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Mark Gross <markgross@kernel.org> Link: https://lore.kernel.org/r/20230805101010.54d49e91@endymion.delvare Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
fnic_clean_pending_aborts() was returning a non-zero value irrespective of
failure or success. This caused the caller of this function to assume that
the device reset had failed, even though it would succeed in most cases. As
a consequence, a successful device reset would escalate to host reset.
If device_add() returns error, the name allocated by dev_set_name() needs
be freed. As the comment of device_add() says, put_device() should be used
to decrease the reference count in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanp().
Fixes: ee959b00c335 ("SCSI: convert struct class_device to struct device") Signed-off-by: Zhu Wang <wangzhu9@huawei.com> Link: https://lore.kernel.org/r/20230803020230.226903-1-wangzhu9@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If device_add() returns error, the name allocated by dev_set_name() needs
be freed. As the comment of device_add() says, put_device() should be used
to give up the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanp().
Fixes: c8806b6c9e82 ("snic: driver for Cisco SCSI HBA") Signed-off-by: Zhu Wang <wangzhu9@huawei.com> Acked-by: Narsimhulu Musini <nmusini@cisco.com> Link: https://lore.kernel.org/r/20230801111421.63651-1-wangzhu9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hyper-V provides the ability to connect Fibre Channel LUNs to the host
system and present them in a guest VM as a SCSI device. I/O to the vFC
device is handled by the storvsc driver. The storvsc driver includes a
partial integration with the FC transport implemented in the generic
portion of the Linux SCSI subsystem so that FC attributes can be displayed
in /sys. However, the partial integration means that some aspects of vFC
don't work properly. Unfortunately, a full and correct integration isn't
practical because of limitations in what Hyper-V provides to the guest.
In particular, in the context of Hyper-V storvsc, the FC transport timeout
function fc_eh_timed_out() causes a kernel panic because it can't find the
rport and dereferences a NULL pointer. The original patch that added the
call from storvsc_eh_timed_out() to fc_eh_timed_out() is faulty in this
regard.
In many cases a timeout is due to a transient condition, so the situation
can be improved by just continuing to wait like with other I/O requests
issued by storvsc, and avoiding the guaranteed panic. For a permanent
failure, continuing to wait may result in a hung thread instead of a panic,
which again may be better.
So fix the panic by removing the storvsc call to fc_eh_timed_out(). This
allows storvsc to keep waiting for a response. The change has been tested
by users who experienced a panic in fc_eh_timed_out() due to transient
timeouts, and it solves their problem.
In the future we may want to deprecate the vFC functionality in storvsc
since it can't be fully fixed. But it has current users for whom it is
working well enough, so it should probably stay for a while longer.
Fixes: 3930d7309807 ("scsi: storvsc: use default I/O timeout handler for FC devices") Cc: stable@vger.kernel.org Signed-off-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/1690606764-79669-1-git-send-email-mikelley@microsoft.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(lightly modified commit message mostly by Linus Torvalds)
The parsing code for /proc/scsi/scsi is disgusting and broken. We should
have just used 'sscanf()' or something simple like that, but the logic may
actually predate our kernel sscanf library routine for all I know. It
certainly predates both git and BK histories.
And we can't change it to be something sane like that now, because the
string matching at the start is done case-insensitively, and the separator
parsing between numbers isn't done at all, so *any* separator will work,
including a possible terminating NUL character.
This interface is root-only, and entirely for legacy use, so there is
absolutely no point in trying to tighten up the parsing. Because any
separator has traditionally worked, it's entirely possible that people have
used random characters rather than the suggested space.
So don't bother to try to pretty it up, and let's just make a minimal patch
that can be back-ported and we can forget about this whole sorry thing for
another two decades.
Just make it at least not read past the end of the supplied data.
Link: https://lore.kernel.org/linux-scsi/b570f5fe-cb7c-863a-6ed9-f6774c219b88@cybernetics.com/ Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin K Petersen <martin.petersen@oracle.com> Cc: James Bottomley <jejb@linux.ibm.com> Cc: Willy Tarreau <w@1wt.eu> Cc: stable@kernel.org Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: Martin K Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We set cache_block_group_error if btrfs_cache_block_group() returns an
error, this is because we could end up not finding space to allocate and
mistakenly return -ENOSPC, and which could then abort the transaction
with the incorrect errno, and in the case of ENOSPC result in a
WARN_ON() that will trip up tests like generic/475.
However there's the case where multiple threads can be racing, one
thread gets the proper error, and the other thread doesn't actually call
btrfs_cache_block_group(), it instead sees ->cached ==
BTRFS_CACHE_ERROR. Again the result is the same, we fail to allocate
our space and return -ENOSPC. Instead we need to set
cache_block_group_error to -EIO in this case to make sure that if we do
not make our allocation we get the appropriate error returned back to
the caller.
CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
Syzbot reported a crash that an ASSERT() got triggered inside
prepare_to_merge().
That ASSERT() makes sure the reloc tree is properly pointed back by its
subvolume tree.
[CAUSE]
After more debugging output, it turns out we had an invalid reloc tree:
BTRFS error (device loop1): reloc tree mismatch, root 8 has no reloc root, expect reloc root key (-8, 132, 8) gen 17
Note the above root key is (TREE_RELOC_OBJECTID, ROOT_ITEM,
QUOTA_TREE_OBJECTID), meaning it's a reloc tree for quota tree.
But reloc trees can only exist for subvolumes, as for non-subvolume
trees, we just COW the involved tree block, no need to create a reloc
tree since those tree blocks won't be shared with other trees.
Only subvolumes tree can share tree blocks with other trees (thus they
have BTRFS_ROOT_SHAREABLE flag).
Thus this new debug output proves my previous assumption that corrupted
on-disk data can trigger that ASSERT().
[FIX]
Besides the dedicated fix and the graceful exit, also let tree-checker to
check such root keys, to make sure reloc trees can only exist for subvolumes.
[BUG]
Syzbot reported a crash that an ASSERT() got triggered inside
prepare_to_merge().
[CAUSE]
The root cause of the triggered ASSERT() is we can have a race between
quota tree creation and relocation.
This leads us to create a duplicated quota tree in the
btrfs_read_fs_root() path, and since it's treated as fs tree, it would
have ROOT_SHAREABLE flag, causing us to create a reloc tree for it.
The bug itself is fixed by a dedicated patch for it, but this already
taught us the ASSERT() is not something straightforward for
developers.
[ENHANCEMENT]
Instead of using an ASSERT(), let's handle it gracefully and output
extra info about the mismatch reloc roots to help debug.
Also with the above ASSERT() removed, we can trigger ASSERT(0)s inside
merge_reloc_roots() later.
Also replace those ASSERT(0)s with WARN_ON()s.
When the call to btrfs_reloc_clone_csums in cow_file_range returns an
error, we jump to the out_unlock label with the extent_reserved variable
set to false. The cleanup at the label will then call
extent_clear_unlock_delalloc on the range from start to end. But we've
already added cur_alloc_size to start before the jump, so there might no
range be left from the newly incremented start to end. Move the check for
'start < end' so that it is reached by also for the !extent_reserved case.
CC: stable@vger.kernel.org # 6.1+ Fixes: a315e68f6e8b ("Btrfs: fix invalid attempt to free reserved space on failure to cow range") Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__extent_writepage could have started on more pages than the one it was
called for. This happens regularly for zoned file systems, and in theory
could happen for compressed I/O if the worker thread was executed very
quickly. For such pages extent_write_cache_pages waits for writeback
to complete before moving on to the next page, which is highly inefficient
as it blocks the flusher thread.
Port over the PageDirty check that was added to write_cache_pages in
commit 515f4a037fb ("mm: write_cache_pages optimise page cleaning") to
fix this.
CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
extent_write_cache_pages stops writing pages as soon as nr_to_write hits
zero. That is the right thing for opportunistic writeback, but incorrect
for data integrity writeback, which needs to ensure that no dirty pages
are left in the range. Thus only stop the writeback for WB_SYNC_NONE
if nr_to_write hits 0.
This is a port of write_cache_pages changes in commit 05fe478dd04e
("mm: write_cache_pages integrity fix").
Note that I've only trigger the problem with other changes to the btrfs
writeback code, but this condition seems worthwhile fixing anyway.
CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: David Sterba <dsterba@suse.com>
[ updated comment ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently we've been having mysterious hangs while running generic/475 on
the CI system. This turned out to be something like this:
Task 1
dmsetup suspend --nolockfs
-> __dm_suspend
-> dm_wait_for_completion
-> dm_wait_for_bios_completion
-> Unable to complete because of IO's on a plug in Task 2
Task 2
wb_workfn
-> wb_writeback
-> blk_start_plug
-> writeback_sb_inodes
-> Infinite loop unable to make an allocation
Task 3
cache_block_group
->read_extent_buffer_pages
->Waiting for IO to complete that can't be submitted because Task 1
suspended the DM device
The problem here is that we need Task 2 to be scheduled completely for
the blk plug to flush. Normally this would happen, we normally wait for
the block group caching to finish (Task 3), and this schedule would
result in the block plug flushing.
However if there's enough free space available from the current caching
to satisfy the allocation we won't actually wait for the caching to
complete. This check however just checks that we have enough space, not
that we can make the allocation. In this particular case we were trying
to allocate 9MiB, and we had 10MiB of free space, but we didn't have
9MiB of contiguous space to allocate, and thus the allocation failed and
we looped.
We specifically don't cycle through the FFE loop until we stop finding
cached block groups because we don't want to allocate new block groups
just because we're caching, so we short circuit the normal loop once we
hit LOOP_CACHING_WAIT and we found a caching block group.
This is normally fine, except in this particular case where the caching
thread can't make progress because the DM device has been suspended.
Fix this by not only waiting for free space to >= the amount of space we
want to allocate, but also that we make some progress in caching from
the time we start waiting. This will keep us from busy looping when the
caching is taking a while but still theoretically has enough space for
us to allocate from, and fixes this particular case by forcing us to
actually sleep and wait for forward progress, which will flush the plug.
With this fix we're no longer hanging with generic/475.
CC: stable@vger.kernel.org # 6.1+ Reviewed-by: Boris Burkov <boris@bur.io> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simulated chips use a mutex for synchronization in driver callbacks so
they must not be called from interrupt context. Set the can_sleep field
of the GPIO chip to true to force users to only use threaded irqs.
The WinSystems WS16C48 I/O address region spans offsets 0x0 through 0xA,
which is a total of 11 bytes. Fix the WS16C48_EXTENT define to the
correct value of 11 so that access to necessary device registers is
properly requested in the ws16c48_probe() callback by the
devm_request_region() function call.
Fixes: 2c05a0f29f41 ("gpio: ws16c48: Implement and utilize register structures") Cc: stable@vger.kernel.org Cc: Paul Demetrotion <pdemetrotion@winsystems.com> Signed-off-by: William Breathitt Gray <william.gray@linaro.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a login request fails, the recovery process should be protected
against parallel resets. It is a known issue that freeing and
registering CRQ's in quick succession can result in a failover CRQ from
the VIOS. Processing a failover during login recovery is dangerous for
two reasons:
1. This will result in two parallel initialization processes, this can
cause serious issues during login.
2. It is possible that the failover CRQ is received but never executed.
We get notified of a pending failover through a transport event CRQ.
The reset is not performed until a INIT CRQ request is received.
Previously, if CRQ init fails during login recovery, then the ibmvnic
irq is freed and the login process returned error. If failover_pending
is true (a transport event was received), then the ibmvnic device
would never be able to process the reset since it cannot receive the
CRQ_INIT request due to the irq being freed. This leaved the device
in a inoperable state.
Therefore, the login failure recovery process must be hardened against
these possible issues. Possible failovers (due to quick CRQ free and
init) must be avoided and any issues during re-initialization should be
dealt with instead of being propagated up the stack. This logic is
similar to that of ibmvnic_probe().
Fixes: dff515a3e71d ("ibmvnic: Harden device login requests") Signed-off-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230809221038.51296-5-nnac123@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Perform a partial reset before sending a login request if any of the
following are true:
1. If a previous request times out. This can be dangerous because the
VIOS could still receive the old login request at any point after
the timeout. Therefore, it is best to re-register the CRQ's and
sub-CRQ's before retrying.
2. If the previous request returns an error that is not described in
PAPR. PAPR provides procedures if the login returns with partial
success or aborted return codes (section L.5.1) but other values
do not have a defined procedure. Previously, these conditions
just returned error from the login function rather than trying
to resolve the issue.
This can cause further issues since most callers of the login
function are not prepared to handle an error when logging in. This
improper cleanup can lead to the device being permanently DOWN'd.
For example, if the VIOS believes that the device is already logged
in then it will return INVALID_STATE (-7). If we never re-register
CRQ's then it will always think that the device is already logged
in. This leaves the device inoperable.
The partial reset involves freeing the sub-CRQs, freeing the CRQ then
registering and initializing a new CRQ and sub-CRQs. This essentially
restarts all communication with VIOS to allow for a fresh login attempt
that will be unhindered by any previous failed attempts.
Fixes: dff515a3e71d ("ibmvnic: Harden device login requests") Signed-off-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230809221038.51296-4-nnac123@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than leaving the DMA unmapping of the login buffers to the
login response handler, move this work into the login release functions.
Previously, these functions were only used for freeing the allocated
buffers. This could lead to issues if there are more than one
outstanding login buffer requests, which is possible if a login request
times out.
If a login request times out, then there is another call to send login.
The send login function makes a call to the login buffer release
function. In the past, this freed the buffers but did not DMA unmap.
Therefore, the VIOS could still write to the old login (now freed)
buffer. It is for this reason that it is a good idea to leave the DMA
unmap call to the login buffers release function.
Since the login buffer release functions now handle DMA unmapping,
remove the duplicate DMA unmapping in handle_login_rsp().
Fixes: dff515a3e71d ("ibmvnic: Harden device login requests") Signed-off-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230809221038.51296-3-nnac123@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the LOGIN CRQ fails to send then we must DMA unmap the response
buffer. Previously, if the CRQ failed then the memory was freed without
DMA unmapping.
Fixes: c98d9cc4170d ("ibmvnic: send_login should check for crq errors") Signed-off-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230809221038.51296-2-nnac123@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that all offsets in a login response buffer are within the size
of the allocated response buffer. Any offsets or lengths that surpass
the allocation are likely the result of an incomplete response buffer.
In these cases, a full reset is necessary.
When attempting to login, the ibmvnic device will allocate a response
buffer and pass a reference to the VIOS. The VIOS will then send the
ibmvnic device a LOGIN_RSP CRQ to signal that the buffer has been filled
with data. If the ibmvnic device does not get a response in 20 seconds,
the old buffer is freed and a new login request is sent. With 2
outstanding requests, any LOGIN_RSP CRQ's could be for the older
login request. If this is the case then the login response buffer (which
is for the newer login request) could be incomplete and contain invalid
data. Therefore, we must enforce strict sanity checks on the response
buffer values.
Testing has shown that the `off_rxadd_buff_size` value is filled in last
by the VIOS and will be the smoking gun for these circumstances.
Until VIOS can implement a mechanism for tracking outstanding response
buffers and a method for mapping a LOGIN_RSP CRQ to a particular login
response buffer, the best ibmvnic can do in this situation is perform a
full reset.
Fixes: dff515a3e71d ("ibmvnic: Harden device login requests") Signed-off-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230809221038.51296-1-nnac123@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device is in error state, marked by the flag
MLX5_DEVICE_STATE_INTERNAL_ERROR, the HW and PCI may not be accessible
and so clock update work should be skipped. Furthermore, such access
through PCI in error state, after calling mlx5_pci_disable_device() can
result in failing to recover from pci errors.
action order 2: tunnel_key set
src_ip 192.168.1.25
dst_ip 192.168.1.26
key_id 4
dst_port 4789
csum pipe
index 3 ref 1 bind 1 installed 3807 sec used 3779 sec firstused 3800 sec
Action statistics:
Sent 120 bytes 2 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
action order 3: mirred (Egress Redirect to device vxlan1) stolen
index 9 ref 1 bind 1 installed 3807 sec used 3779 sec firstused 3800 sec
Action statistics:
Sent 120 bytes 2 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
used_hw_stats delayed
When handling FIB events, the rule in post act will not be deleted.
And because the post act rule has packet reformat and modify header
actions, also will hit the following syndromes:
mlx5_core 0000:08:00.0: mlx5_cmd_out_err:829:(pid 11613): DEALLOC_MODIFY_HEADER_CONTEXT(0x941) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x1ab444), err(-22)
mlx5_core 0000:08:00.0: mlx5_cmd_out_err:829:(pid 11613): DEALLOC_PACKET_REFORMAT_CONTEXT(0x93e) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x179e84), err(-22)
Fix it by unoffloading post act rule when handling FIB events.
Fixes: 314e1105831b ("net/mlx5e: Add post act offload/unoffload API") Signed-off-by: Chris Mi <cmi@nvidia.com> Reviewed-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When querying eswitch functions 0 is a valid number of host VFs. After
introducing ARM SRIOV falling through to getting the max value from PCI
results in using the total VFs allowed on the ARM for the host.
Fixes: 86eec50beaf3 ("net/mlx5: Support querying max VFs from device"); Signed-off-by: Daniel Jurgens <danielj@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing wrong calculation of the modify hdr pattern size,
where the previously calculated number would not be enough
to accommodate the required number of actions.
The flow rule can be splited, and the extra post_act rules are added
to post_act table. It's possible to trigger memleak when the rule
forwards packets from internal port and over tunnel, in the case that,
for example, CT 'new' state offload is allowed. As int_port object is
assigned to the flow attribute of post_act rule, and its refcnt is
incremented by mlx5e_tc_int_port_get(), but mlx5e_tc_int_port_put() is
not called, the refcnt is never decremented, then int_port is never
freed.
Hold RTNL lock when calling xdp_set_features() with a registered netdev,
as the call triggers the netdev notifiers. This could happen when
switching from uplink rep to nic profile for example.
drivers/dma/owl-dma.c:208: warning: expecting prototype for struct owl_dma_pchan. Prototype was for struct owl_dma_vchan instead HDRTEST usr/include/sound/asequencer.h
Disabling IDXD device doesn't reset Page Request Service (PRS)
disable flag to its initial value 0. This may cause user confusion
because once PRS is disabled user will see PRS still remains the
previous setting (i.e. disabled) via sysfs interface even after the
device is disabled.
To eliminate user confusion, reset PRS disable flag to ensure that
the PRS flag bit reflects correct state after the device is disabled.
Additionally, simplify the code by setting wq->flags to 0, which clears
all flag bits, including any future additions.
When 'mcf_edma' is allocated, some space is allocated for a
flexible array at the end of the struct. 'chans' item are allocated, that is
to say 'pdata->dma_channels'.
Then, this number of item is stored in 'mcf_edma->n_chans'.
A few lines later, if 'mcf_edma->n_chans' is 0, then a default value of 64
is set.
This ends to no space allocated by devm_kzalloc() because chans was 0, but
64 items are read and/or written in some not allocated memory.
Change the logic to define a default value before allocating the memory.
hns3_dbg_fill_content()/hclge_dbg_fill_content() is aim to integrate some
items to a string for content, and we add '\n' and '\0' in the last
two bytes of content.
strscpy() will add '\0' in the last byte of destination buffer(one of
items), it result in finishing content print ahead of schedule and some
dump content truncation.
One Error log shows as below:
cat mac_list/uc
UC MAC_LIST:
Expected:
UC MAC_LIST:
FUNC_ID MAC_ADDR STATE
pf 00:2b:19:05:03:00 ACTIVE
The destination buffer is length-bounded and not required to be
NUL-terminated, so just change strscpy() to memcpy() to fix it.
Fixes: 1cf3d5567f27 ("net: hns3: fix strncpy() not using dest-buf length as length issue") Signed-off-by: Hao Chen <chenhao418@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Link: https://lore.kernel.org/r/20230809020902.1941471-1-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A netlink dump callback can return a positive number to signal that more
information needs to be dumped or zero to signal that the dump is
complete. In the second case, the core netlink code will append the
NLMSG_DONE message to the skb in order to indicate to user space that
the dump is complete.
The nexthop bucket dump callback always returns a positive number if
nexthop buckets were filled in the provided skb, even if the dump is
complete. This means that a dump will span at least two recvmsg() calls
as long as nexthop buckets are present. In the last recvmsg() call the
dump callback will not fill in any nexthop buckets because the previous
call indicated that the dump should restart from the last dumped nexthop
ID plus one.
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id 10 group 1 type resilient buckets 2
# strace -e sendto,recvmsg -s 5 ip nexthop bucket
sendto(3, [[{nlmsg_len=24, nlmsg_type=RTM_GETNEXTHOPBUCKET, nlmsg_flags=NLM_F_REQUEST|NLM_F_DUMP, nlmsg_seq=1691396980, nlmsg_pid=0}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], {nlmsg_len=0, nlmsg_type=0 /* NLMSG_??? */, nlmsg_flags=0, nlmsg_seq=0, nlmsg_pid=0}], 152, 0, NULL, 0) = 152
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 128
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[[{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396980, nlmsg_pid=347}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], [{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396980, nlmsg_pid=347}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}]], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 128
id 10 index 0 idle_time 6.66 nhid 1
id 10 index 1 idle_time 6.66 nhid 1
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 20
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[{nlmsg_len=20, nlmsg_type=NLMSG_DONE, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396980, nlmsg_pid=347}, 0], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 20
+++ exited with 0 +++
This behavior is both inefficient and buggy. If the last nexthop to be
dumped had the maximum ID of 0xffffffff, then the dump will restart from
0 (0xffffffff + 1) and never end:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id $((2**32-1)) group 1 type resilient buckets 2
# ip nexthop bucket
id 4294967295 index 0 idle_time 5.55 nhid 1
id 4294967295 index 1 idle_time 5.55 nhid 1
id 4294967295 index 0 idle_time 5.55 nhid 1
id 4294967295 index 1 idle_time 5.55 nhid 1
[...]
Fix by adjusting the dump callback to return zero when the dump is
complete. After the fix only one recvmsg() call is made and the
NLMSG_DONE message is appended to the RTM_NEWNEXTHOPBUCKET responses:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id $((2**32-1)) group 1 type resilient buckets 2
# strace -e sendto,recvmsg -s 5 ip nexthop bucket
sendto(3, [[{nlmsg_len=24, nlmsg_type=RTM_GETNEXTHOPBUCKET, nlmsg_flags=NLM_F_REQUEST|NLM_F_DUMP, nlmsg_seq=1691396737, nlmsg_pid=0}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], {nlmsg_len=0, nlmsg_type=0 /* NLMSG_??? */, nlmsg_flags=0, nlmsg_seq=0, nlmsg_pid=0}], 152, 0, NULL, 0) = 152
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 148
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[[{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396737, nlmsg_pid=350}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], [{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396737, nlmsg_pid=350}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], [{nlmsg_len=20, nlmsg_type=NLMSG_DONE, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396737, nlmsg_pid=350}, 0]], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 148
id 4294967295 index 0 idle_time 6.61 nhid 1
id 4294967295 index 1 idle_time 6.61 nhid 1
+++ exited with 0 +++
Note that if the NLMSG_DONE message cannot be appended because of size
limitations, then another recvmsg() will be needed, but the core netlink
code will not invoke the dump callback and simply reply with a
NLMSG_DONE message since it knows that the callback previously returned
zero.
Add a test that fails before the fix:
# ./fib_nexthops.sh -t basic_res
[...]
TEST: Maximum nexthop ID dump [FAIL]
[...]
And passes after it:
# ./fib_nexthops.sh -t basic_res
[...]
TEST: Maximum nexthop ID dump [ OK ]
[...]
Fixes: 8a1bbabb034d ("nexthop: Add netlink handlers for bucket dump") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230808075233.3337922-4-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtm_dump_nexthop_bucket_nh() is used to dump nexthop buckets belonging
to a specific resilient nexthop group. The function returns a positive
return code (the skb length) upon both success and failure.
The above behavior is problematic. When a complete nexthop bucket dump
is requested, the function that walks the different nexthops treats the
non-zero return code as an error. This causes buckets belonging to
different resilient nexthop groups to be dumped using different buffers
even if they can all fit in the same buffer:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id 10 group 1 type resilient buckets 1
# ip nexthop add id 20 group 1 type resilient buckets 1
# strace -e recvmsg -s 0 ip nexthop bucket
[...]
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[...], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 64
id 10 index 0 idle_time 10.27 nhid 1
[...]
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[...], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 64
id 20 index 0 idle_time 6.44 nhid 1
[...]
Fix by only returning a non-zero return code when an error occurred and
restarting the dump from the bucket index we failed to fill in. This
allows buckets belonging to different resilient nexthop groups to be
dumped using the same buffer:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id 10 group 1 type resilient buckets 1
# ip nexthop add id 20 group 1 type resilient buckets 1
# strace -e recvmsg -s 0 ip nexthop bucket
[...]
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[...], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 128
id 10 index 0 idle_time 30.21 nhid 1
id 20 index 0 idle_time 26.7 nhid 1
[...]
While this change is more of a performance improvement change than an
actual bug fix, it is a prerequisite for a subsequent patch that does
fix a bug.
Fixes: 8a1bbabb034d ("nexthop: Add netlink handlers for bucket dump") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230808075233.3337922-3-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A netlink dump callback can return a positive number to signal that more
information needs to be dumped or zero to signal that the dump is
complete. In the second case, the core netlink code will append the
NLMSG_DONE message to the skb in order to indicate to user space that
the dump is complete.
The nexthop dump callback always returns a positive number if nexthops
were filled in the provided skb, even if the dump is complete. This
means that a dump will span at least two recvmsg() calls as long as
nexthops are present. In the last recvmsg() call the dump callback will
not fill in any nexthops because the previous call indicated that the
dump should restart from the last dumped nexthop ID plus one.
This behavior is both inefficient and buggy. If the last nexthop to be
dumped had the maximum ID of 0xffffffff, then the dump will restart from
0 (0xffffffff + 1) and never end:
# ip nexthop add id $((2**32-1)) blackhole
# ip nexthop
id 4294967295 blackhole
id 4294967295 blackhole
[...]
Fix by adjusting the dump callback to return zero when the dump is
complete. After the fix only one recvmsg() call is made and the
NLMSG_DONE message is appended to the RTM_NEWNEXTHOP response:
Note that if the NLMSG_DONE message cannot be appended because of size
limitations, then another recvmsg() will be needed, but the core netlink
code will not invoke the dump callback and simply reply with a
NLMSG_DONE message since it knows that the callback previously returned
zero.
Add a test that fails before the fix:
# ./fib_nexthops.sh -t basic
[...]
TEST: Maximum nexthop ID dump [FAIL]
[...]
And passes after it:
# ./fib_nexthops.sh -t basic
[...]
TEST: Maximum nexthop ID dump [ OK ]
[...]
Fixes: ab84be7e54fc ("net: Initial nexthop code") Reported-by: Petr Machata <petrm@nvidia.com> Closes: https://lore.kernel.org/netdev/87sf91enuf.fsf@nvidia.com/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230808075233.3337922-2-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The workaround implemented in commit 3222b5b613db ("net: enetc:
initialize RFS/RSS memories for unused ports too") is no longer
effective after commit 6fffbc7ae137 ("PCI: Honor firmware's device
disabled status"). Thus, it has introduced a regression and we see AER
errors being reported again:
$ ip link set sw2p0 up && dhclient -i sw2p0 && ip addr show sw2p0
fsl_enetc 0000:00:00.2 eno2: configuring for fixed/internal link mode
fsl_enetc 0000:00:00.2 eno2: Link is Up - 2.5Gbps/Full - flow control rx/tx
mscc_felix 0000:00:00.5 swp2: configuring for fixed/sgmii link mode
mscc_felix 0000:00:00.5 swp2: Link is Up - 1Gbps/Full - flow control off
sja1105 spi2.2 sw2p0: configuring for phy/rgmii-id link mode
sja1105 spi2.2 sw2p0: Link is Up - 1Gbps/Full - flow control off
pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
pcieport 0000:00:1f.0: AER: can't find device of ID0000
Rob's suggestion is to reimplement the enetc driver workaround as a
PCI fixup, and to modify the PCI core to run the fixups for all PCI
functions. This change handles the first part.
We refactor the common code in enetc_psi_create() and enetc_psi_destroy(),
and use the PCI fixup only for those functions for which enetc_pf_probe()
won't get called. This avoids some work being done twice for the PFs
which are enabled.
In externel_lb process, the hns3 driver call napi_disable()
first, then the reset happen, then the restore process of the
externel_lb will fail, and will not call napi_enable(). When
doing externel_lb again, napi_disable() will be double call,
cause a deadlock of rtnl_lock().
This patch use the HNS3_NIC_STATE_DOWN state to protect the
calling of napi_disable() and napi_enable() in externel_lb
process, just as the usage in ndo_stop() and ndo_start().
Fixes: 04b6ba143521 ("net: hns3: add support for external loopback test") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230807113452.474224-5-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some configure flow of hns3 driver, for example, change mtu, it will
disable MAC through firmware before configuration. But firmware disables
MAC asynchronously. The rx traffic may be not stopped in this case.
So fixes it by waiting until mac link is down.
Fixes: a9775bb64aa7 ("net: hns3: fix set and get link ksettings issue") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230807113452.474224-4-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the tagging protocol in current use is "ocelot-8021q" and we unbind
the driver, we see this splat:
$ echo '0000:00:00.2' > /sys/bus/pci/drivers/fsl_enetc/unbind
mscc_felix 0000:00:00.5 swp0: left promiscuous mode
sja1105 spi2.0: Link is Down
DSA: tree 1 torn down
mscc_felix 0000:00:00.5 swp2: left promiscuous mode
sja1105 spi2.2: Link is Down
DSA: tree 3 torn down
fsl_enetc 0000:00:00.2 eno2: left promiscuous mode
mscc_felix 0000:00:00.5: Link is Down
------------[ cut here ]------------
RTNL: assertion failed at net/dsa/tag_8021q.c (409)
WARNING: CPU: 1 PID: 329 at net/dsa/tag_8021q.c:409 dsa_tag_8021q_unregister+0x12c/0x1a0
Modules linked in:
CPU: 1 PID: 329 Comm: bash Not tainted 6.5.0-rc3+ #771
pc : dsa_tag_8021q_unregister+0x12c/0x1a0
lr : dsa_tag_8021q_unregister+0x12c/0x1a0
Call trace:
dsa_tag_8021q_unregister+0x12c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
RTNL: assertion failed at net/8021q/vlan_core.c (376)
WARNING: CPU: 1 PID: 329 at net/8021q/vlan_core.c:376 vlan_vid_del+0x1b8/0x1f0
CPU: 1 PID: 329 Comm: bash Tainted: G W 6.5.0-rc3+ #771
pc : vlan_vid_del+0x1b8/0x1f0
lr : vlan_vid_del+0x1b8/0x1f0
dsa_tag_8021q_unregister+0x8c/0x1a0
felix_tag_8021q_teardown+0x130/0x150
felix_teardown+0x3c/0xd8
dsa_tree_teardown_switches+0xbc/0xe0
dsa_unregister_switch+0x168/0x260
felix_pci_remove+0x30/0x60
pci_device_remove+0x4c/0x100
device_release_driver_internal+0x188/0x288
device_links_unbind_consumers+0xfc/0x138
device_release_driver_internal+0xe0/0x288
device_driver_detach+0x24/0x38
unbind_store+0xd8/0x108
drv_attr_store+0x30/0x50
DSA: tree 0 torn down
This was somewhat not so easy to spot, because "ocelot-8021q" is not the
default tagging protocol, and thus, not everyone who tests the unbinding
path may have switched to it beforehand. The default
felix_tag_npi_teardown() does not require rtnl_lock() to be held.
Fixes: 7c83a7c539ab ("net: dsa: add a second tagger for Ocelot switches based on tag_8021q") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20230803134253.2711124-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the AR8032 part does not support wol, remove related callbacks
from it.
Fixes: 5800091a2061 ("net: phy: at803x: add support for AR8032 PHY") Signed-off-by: Li Yang <leoyang.li@nxp.com> Cc: David Bauer <mail@david-bauer.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
$ ip route
10.0.0.0/24 dev swp5 proto kernel scope link src 10.0.0.1 rt_trap
10.0.1.0/24 nhid 20 via 10.0.0.2 dev swp5 rt_trap
When creating a route referencing a nexthop via its ID, the nexthop will
be stored in a separate nh pointer instead of the array of nexthops in
the fib_info struct. This causes issues since fib_info_nh() only handles
the nexthops array, but not the separate nh pointer, and will loudly
WARN about it.
In contrast fib_info_nhc() handles both, but returns a fib_nh_common
pointer instead of a fib_nh pointer. Luckily we only ever access fields
from the fib_nh_common parts, so we can just replace all instances of
fib_info_nh() with fib_info_nhc() and access the fields via their
fib_nh_common names.
This allows handling IPv4 routes with an external nexthop, and they now
get offloaded as expected:
$ ip route
10.0.0.0/24 dev swp5 proto kernel scope link src 10.0.0.1 rt_trap
10.0.1.0/24 nhid 20 via 10.0.0.2 dev swp5 offload rt_offload
TLS records end with a 16B tag. For TLS device offload we only
need to make space for this tag in the stream, the device will
generate and replace it with the actual calculated tag.
Long time ago the code would just re-reference the head frag
which mostly worked but was suboptimal because it prevented TCP
from combining the record into a single skb frag. I'm not sure
if it was correct as the first frag may be shorter than the tag.
The commit under fixes tried to replace that with using the page
frag and if the allocation failed rolling back the data, if record
was long enough. It achieves better fragment coalescing but is
also buggy.
We don't roll back the iterator, so unless we're at the end of
send we'll skip the data we designated as tag and start the
next record as if the rollback never happened.
There's also the possibility that the record was constructed
with MSG_MORE and the data came from a different syscall and
we already told the user space that we "got it".
Allocate a single dummy page and use it as fallback.
Found by code inspection, and proven by forcing allocation
failures.
Fixes: e7b159a48ba6 ("net/tls: remove the record tail optimization") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing the ODP registration flow to set the iova correctly.
The calculation in ib_umem_num_dma_blocks() function assumes the iova of
the umem is set correctly.
When iova is not set, the calculation in ib_umem_num_dma_blocks() is
equivalent to length/page_size, which is true only when memory is aligned.
For unaligned memory, iova must be set for the ALIGN() in the
ib_umem_num_dma_blocks() to take effect and return a correct value.
mlx5_ib uses ib_umem_num_dma_blocks() to decide the mkey size to use for
the MR. Without this fix, when registering unaligned ODP MR, a wrong
size mkey might be chosen and this might cause the UMR to fail.
Userspace should not be able to trigger DRM_ERROR messages to spam the
logs; especially not through atomic commit parameters which are
completely legitimate for userspace to attempt.
On system resume, the driver might call it6505_poweron directly if the
runtime PM hasn't been enabled. In such case, pm_runtime_get_if_in_use
will always return 0 because dev->power.runtime_status stays at
RPM_SUSPENDED, and the IRQ will never be handled.
Use it6505->powered from the driver struct fixes this because it always
gets updated when it6505_poweron is called.
Fixes: 5eb9a4314053 ("drm/bridge: it6505: Guard bridge power in IRQ handler") Signed-off-by: Pin-yen Lin <treapking@chromium.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230727100131.2338127-1-treapking@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some systems are only connected by HDMI or DP, so warning related to
missing eDP is unnecessary. Downgrade to debug instead.
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com> Fixes: 6d9b6dceaa51 ("drm/amd/display: only warn once in dce110_edp_wait_for_hpd_ready()") Reported-by: Mastan.Katragadda@amd.com Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During hotplug remove it is possible that the update counters work
might be pending, and may run after memory has been freed.
Cancel the update counters work before freeing memory.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Signed-off-by: Douglas Miller <doug.miller@cornelisnetworks.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Link: https://lore.kernel.org/r/169099756100.3927190.15284930454106475280.stgit@awfm-02.cornelisnetworks.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change in iavf_fdir_is_dup_fltr adds a spinlock around a loop which
iterates over all filters and looks for a duplicate. The filter can be
removed from list and freed from memory at the same time it's being
compared. All other places where filters are deleted are already
protected with spinlock.
The remaining changes protect adapter->fdir_active_fltr variable so now
all its uses are under a spinlock.
Fixes: 527691bf0682 ("iavf: Support IPv4 Flow Director filters") Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230807205011.3129224-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using the syzkaller repro with reduced packet size it was discovered
that XDP_PACKET_HEADROOM is not checked in tun_can_build_skb(),
although pad may be incremented in tun_build_skb(). This may end up
with exceeding the PAGE_SIZE limit in tun_build_skb().
Jason Wang <jasowang@redhat.com> proposed to count XDP_PACKET_HEADROOM
always (e.g. without rcu_access_pointer(tun->xdp_prog)) in
tun_can_build_skb() since there's a window during which XDP program
might be attached between tun_can_build_skb() and tun_build_skb().
BUG_ON(!vlan_info) is triggered in unregister_vlan_dev() with
following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add bond0 type bond mode 0
# ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
# ip netns exec ns1 ip link set bond_slave_1 master bond0
# ip netns exec ns1 ip link add link bond_slave_1 name vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link bond0 name bond0_vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set bond_slave_1 nomaster
# ip netns del ns1
The logical analysis of the problem is as follows:
1. create ETH_P_8021AD protocol vlan10 for bond_slave_1:
register_vlan_dev()
vlan_vid_add()
vlan_info_alloc()
__vlan_vid_add() // add [ETH_P_8021AD, 10] vid to bond_slave_1
2. create ETH_P_8021AD protocol bond0_vlan10 for bond0:
register_vlan_dev()
vlan_vid_add()
__vlan_vid_add()
vlan_add_rx_filter_info()
if (!vlan_hw_filter_capable(dev, proto)) // condition established because bond0 without NETIF_F_HW_VLAN_STAG_FILTER
return 0;
if (netif_device_present(dev))
return dev->netdev_ops->ndo_vlan_rx_add_vid(dev, proto, vid); // will be never called
// The slaves of bond0 will not refer to the [ETH_P_8021AD, 10] vid.
3. detach bond_slave_1 from bond0:
__bond_release_one()
vlan_vids_del_by_dev()
list_for_each_entry(vid_info, &vlan_info->vid_list, list)
vlan_vid_del(dev, vid_info->proto, vid_info->vid);
// bond_slave_1 [ETH_P_8021AD, 10] vid will be deleted.
// bond_slave_1->vlan_info will be assigned NULL.
4. delete vlan10 during delete ns1:
default_device_exit_batch()
dev->rtnl_link_ops->dellink() // unregister_vlan_dev() for vlan10
vlan_info = rtnl_dereference(real_dev->vlan_info); // real_dev of vlan10 is bond_slave_1
BUG_ON(!vlan_info); // bond_slave_1->vlan_info is NULL now, bug is triggered!!!
Add S-VLAN tag related features support to bond driver. So the bond driver
will always propagate the VLAN info to its slaves.
Fix a refcount underflow problem reported by syzbot that can happen
when a system is running out of memory. If xp_alloc_tx_descs() fails,
and it can only fail due to not having enough memory, then the error
path is triggered. In this error path, the refcount of the pool is
decremented as it has incremented before. However, the reference to
the pool in the socket was not nulled. This means that when the socket
is closed later, the socket teardown logic will think that there is a
pool attached to the socket and try to decrease the refcount again,
leading to a refcount underflow.
I chose this fix as it involved adding just a single line. Another
option would have been to move xp_get_pool() and the assignment of
xs->pool to after the if-statement and using xs_umem->pool instead of
xs->pool in the whole if-statement resulting in somewhat simpler code,
but this would have led to much more churn in the code base perhaps
making it harder to backport.
Fixes: ba3beec2ec1d ("xsk: Fix possible crash when multiple sockets are created") Reported-by: syzbot+8ada0057e69293a05fd4@syzkaller.appspotmail.com Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/r/20230809142843.13944-1-magnus.karlsson@gmail.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The blamed commit has broken probing on
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi when &enetc_port0
(PCI function 0) has status = "disabled".
Background: pci_scan_slot() has logic to say that if the function 0 of a
device is absent, the entire device is absent and we can skip the other
functions entirely. Traditionally, this has meant that
pci_bus_read_dev_vendor_id() returns an error code for that function.
However, since the blamed commit, there is an extra confounding
condition: function 0 of the device exists and has a valid vendor id,
but it is disabled in the device tree. In that case, pci_scan_slot()
would incorrectly skip the entire device instead of just that function.
In the case of NXP LS1028A, status = "disabled" does not mean that the
PCI function's config space is not available for reading. It is, but the
Ethernet port is just not functionally useful with a particular SerDes
protocol configuration (0x9999) due to pinmuxing constraints of the Soc.
So, pci_scan_slot() skips all other functions on the ENETC ECAM
(enetc_port1, enetc_port2, enetc_mdio_pf3 etc) when just enetc_port0 had
to not be probed.
There is an additional regression introduced by the change, caused by
its fundamental premise. The enetc driver needs to run code for all PCI
functions, regardless of whether they're enabled or not in the device
tree. That is no longer possible if the driver's probe function is no
longer called. But Rob recommends that we move the of_device_is_available()
detection to dev->match_driver, and this makes the PCI fixups still run
on all functions, while just probing drivers for those functions that
are enabled. So, a separate change in the enetc driver will have to move
the workarounds to a PCI fixup.
Tuning of the effective buffer size through setsockopts was working for
SMC traffic only but not for TCP fall-back connections even before
commit 0227f058aa29 ("net/smc: Unbind r/w buffer size from clcsock and
make them tunable"). That change made it apparent that TCP fall-back
connections would use net.smc.[rw]mem as buffer size instead of
net.ipv4_tcp_[rw]mem.
Amend the code that copies attributes between the (TCP) clcsock and the
SMC socket and adjust buffer sizes appropriately:
- Copy over sk_userlocks so that both sockets agree on whether tuning
via setsockopt is active.
- When falling back to TCP use sk_sndbuf or sk_rcvbuf as specified with
setsockopt. Otherwise, use the sysctl value for TCP/IPv4.
- Likewise, use either values from setsockopt or from sysctl for SMC
(duplicated) on successful SMC connect.
In smc_tcp_listen_work() drop the explicit copy of buffer sizes as that
is taken care of by the attribute copy.
Fixes: 0227f058aa29 ("net/smc: Unbind r/w buffer size from clcsock and make them tunable") Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0227f058aa29 ("net/smc: Unbind r/w buffer size from clcsock
and make them tunable") introduced the net.smc.rmem and net.smc.wmem
sysctls to specify the size of buffers to be used for SMC type
connections. This created a regression for users that specified the
buffer size via setsockopt() as the effective buffer size was now
doubled.
Re-introduce the division by 2 in the SMC buffer create code and level
this out by duplicating the net.smc.[rw]mem values used for initializing
sk_rcvbuf/sk_sndbuf at socket creation time. This gives users of both
methods (setsockopt or sysctl) the effective buffer size that they
expect.
Initialize net.smc.[rw]mem from its own constant of 64kB, respectively.
Internal performance tests show that this value is a good compromise
between throughput/latency and memory consumption. Also, this decouples
it from any tuning that was done to net.ipv4.tcp_[rw]mem[1] before the
module for SMC protocol was loaded. Check that no more than INT_MAX / 2
is assigned to net.smc.[rw]mem, in order to avoid any overflow condition
when that is doubled for use in sk_sndbuf or sk_rcvbuf.
While at it, drop the confusing sk_buf_size variable from
__smc_buf_create and name "compressed" buffer size variables more
consistently.
Background:
Before the commit mentioned above, SMC's buffer allocator in
__smc_buf_create() always used half of the sockets' sk_rcvbuf/sk_sndbuf
value as initial value to search for appropriate buffers. If the search
resorted to using a bigger buffer when all buffers of the specified
size were busy, the duplicate of the used effective buffer size is
stored back to sk_rcvbuf/sk_sndbuf.
When available, buffers of exactly the size that a user had specified as
input to setsockopt() were used, despite setsockopt()'s documentation in
"man 7 socket" talking of a mandatory duplication:
[...]
SO_SNDBUF
Sets or gets the maximum socket send buffer in bytes.
The kernel doubles this value (to allow space for book‐
keeping overhead) when it is set using setsockopt(2),
and this doubled value is returned by getsockopt(2).
The default value is set by the
/proc/sys/net/core/wmem_default file and the maximum
allowed value is set by the /proc/sys/net/core/wmem_max
file. The minimum (doubled) value for this option is
2048.
[...]
Fixes: 0227f058aa29 ("net/smc: Unbind r/w buffer size from clcsock and make them tunable") Co-developed-by: Jan Karcher <jaka@linux.ibm.com> Signed-off-by: Jan Karcher <jaka@linux.ibm.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
value changed: 0x0000000000000000 -> 0x0000000020000081
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 6.4.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023
Fixes: 69e3c75f4d54 ("net: TX_RING and packet mmap") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230803145600.2937518-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ionic_start_queues_reconfig returns an error code if txrx_init fails.
Handle this error code in the relevant places.
This fixes a corner case where the device could get left in a detached
state if the CMB reconfig fails and the attempt to clean up the mess
also fails. Note that calling netif_device_attach when the netdev is
already attached does not lead to unexpected behavior.
Change goto name "errout" to "err_out" to maintain consistency across
goto statements.
Fixes: 40bc471dc714 ("ionic: add tx/rx-push support with device Component Memory Buffers") Fixes: 6f7d6f0fd7a3 ("ionic: pull reset_queues into tx_timeout handler") Signed-off-by: Nitya Sunkad <nitya.sunkad@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Access to shared variables through hrtimer requires locking in order
to protect the variables because actions to write into these variables
(oper_gate_closed, admin_gate_closed, and qbv_transition) might potentially
occur simultaneously. This patch provides a locking mechanisms to avoid
such scenarios.
Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed") Suggested-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Tested-by: Naama Meir <naamax.meir@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20230807205129.3129346-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coccicheck reports the error below:
net/mptcp/protocol.c:3330:15-28: ERROR: test of a variable/field address
Since the address of msk->cb_flags is used in __test_and_clear_bit, the
address should not be NULL. The judgment for if (unlikely(msk->cb_flags))
will always be true, we should check the real value of msk->cb_flags here.
Fixes: 65a569b03ca8 ("mptcp: optimize release_cb for the common case") Signed-off-by: Xiang Yang <xiangyang3@huawei.com> Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net> Link: https://lore.kernel.org/r/20230803072438.1847500-1-xiangyang3@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a kernel with CONFIG_MISDN_DSP=y and CONFIG_CFI_CLANG=y,
there is a failure when dsp_cmx_send() is called indirectly from
call_timer_fn():
The function pointer prototype that call_timer_fn() expects is
void (*fn)(struct timer_list *)
whereas dsp_cmx_send() has a parameter type of 'void *', which causes
the control flow integrity checks to fail because the parameter types do
not match.
Change dsp_cmx_send()'s parameter type to be 'struct timer_list' to
match the expected prototype. The argument is unused anyways, so this
has no functional change, aside from avoiding the CFI failure.
Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202308020936.58787e6c-oliver.sang@intel.com Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Fixes: e313ac12eb13 ("mISDN: Convert timers to use timer_setup()") Link: https://lore.kernel.org/r/20230802-fix-dsp_cmx_send-cfi-failure-v1-1-2f2e79b0178d@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a 200ms delay after sending a ctrl report to Quadro,
Octo, D5 Next and Aquaero to give them enough time to
process the request and save the data to memory. Otherwise,
under heavier userspace loads where multiple sysfs entries
are usually set in quick succession, a new ctrl report could
be requested from the device while it's still processing the
previous one and fail with -EPIPE. The delay is only applied
if two ctrl report operations are near each other in time.
Reported by a user on Github [1] and tested by both of us.
strp_done is only called when psock->progs.stream_parser is not NULL,
but stream_parser was set to NULL by sk_psock_stop_strp(), called
by sk_psock_drop() earlier. So, strp_done can never be called.
Introduce SK_PSOCK_RX_ENABLED to mark whether there is strp on psock.
Change the condition for calling strp_done from judging whether
stream_parser is set to judging whether this flag is set. This flag is
only set once when strp_init() succeeds, and will never be cleared later.
Fixes: c0d95d3380ee ("bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap") Signed-off-by: Xu Kuohai <xukuohai@huawei.com> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/r/20230804073740.194770-3-xukuohai@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sock_map_del_link() operates on both SOCKMAP and SOCKHASH, although
both types have member named "progs", the offset of "progs" member in
these two types is different, so "progs" should be accessed with the
real map type.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Xu Kuohai <xukuohai@huawei.com> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/r/20230804073740.194770-2-xukuohai@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xdp->frame_sz > PAGE_SIZE check was introduced in commit c8741e2bfe87
("xdp: Allow bpf_xdp_adjust_tail() to grow packet size"). But Jesper
Dangaard Brouer <jbrouer@redhat.com> noted that after introducing the
xdp_init_buff() which all XDP driver use - it's safe to remove this
check. The original intend was to catch cases where XDP drivers have
not been updated to use xdp.frame_sz, but that is not longer a concern
(since xdp_init_buff).
Running the initial syzkaller repro it was discovered that the
contiguous physical memory allocation is used for both xdp paths in
tun_get_user(), e.g. tun_build_skb() and tun_alloc_skb(). It was also
stated by Jesper Dangaard Brouer <jbrouer@redhat.com> that XDP can
work on higher order pages, as long as this is contiguous physical
memory (e.g. a page).
Some test cases check that the group timer is (or isn't) 0. Instead of
grepping for "0.00" grep for " 0.00" as the former can also match
"260.00" which is the default group membership interval.
As explained in commit 8bcfb4ae4d97 ("selftests: forwarding: Fix failing
tests with old libnet"), old versions of libnet (used by mausezahn) do
not use the "SO_BINDTODEVICE" socket option. For IP unicast packets,
this can be solved by prefixing mausezahn invocations with "ip vrf
exec". However, IP multicast packets do not perform routing and simply
egress the bound device, which does not exist in this case.
Fix by specifying the source and destination MAC of the packet which
will cause mausezahn to use a packet socket instead of an IP socket.
As explained in commit 8bcfb4ae4d97 ("selftests: forwarding: Fix failing
tests with old libnet"), old versions of libnet (used by mausezahn) do
not use the "SO_BINDTODEVICE" socket option. For IP unicast packets,
this can be solved by prefixing mausezahn invocations with "ip vrf
exec". However, IP multicast packets do not perform routing and simply
egress the bound device, which does not exist in this case.
Fix by specifying the source and destination MAC of the packet which
will cause mausezahn to use a packet socket instead of an IP socket.
Fixes: 3446dcd7df05 ("selftests: forwarding: bridge_mdb_max: Add a new selftest") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-17-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The test checks that filters that match on source or destination MAC
were only hit once. A host can send more than one packet with a given
source or destination MAC, resulting in failures.
Fix by relaxing the success criterion and instead check that the filters
were not hit zero times. Using tc_check_at_least_x_packets() is also an
option, but it is not available in older kernels.
The test relies on 'nc' being the netcat version from the nmap project.
While this seems to be the case on Fedora, it is not the case on Ubuntu,
resulting in failures such as [1].
Fix by explicitly using the 'ncat' utility from the nmap project and the
skip the test in case it is not installed.
The default timeout for selftests is 45 seconds, but it is not enough
for forwarding selftests which can takes minutes to finish depending on
the number of tests cases:
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# TEST: IGMPv2 report 239.10.10.10 [ OK ]
# TEST: IGMPv2 leave 239.10.10.10 [ OK ]
# TEST: IGMPv3 report 239.10.10.10 is_include [ OK ]
# TEST: IGMPv3 report 239.10.10.10 include -> allow [ OK ]
#
not ok 1 selftests: net/forwarding: bridge_igmp.sh # TIMEOUT 45 seconds
Fix by switching off the timeout and setting it to 0. A similar change
was done for BPF selftests in commit 6fc5916cc256 ("selftests: bpf:
Switch off timeout").
Fixes: 81573b18f26d ("selftests/net/forwarding: add Makefile to install tests") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/8d149f8c-818e-d141-a0ce-a6bae606bc22@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-3-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As explained in [1], the forwarding selftests are meant to be run with
either physical loopbacks or veth pairs. The interfaces are expected to
be specified in a user-provided forwarding.config file or as command
line arguments. By default, this file is not present and the tests fail:
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
[...]
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# Command line is not complete. Try option "help"
# Failed to create netif
not ok 1 selftests: net/forwarding: bridge_igmp.sh # exit=1
[...]
Fix by skipping a test if interfaces are not provided either via the
configuration file or command line arguments.
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
[...]
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# SKIP: Cannot create interface. Name not specified
ok 1 selftests: net/forwarding: bridge_igmp.sh # SKIP
[1] tools/testing/selftests/net/forwarding/README
Fixes: 81573b18f26d ("selftests/net/forwarding: add Makefile to install tests") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/856d454e-f83c-20cf-e166-6dc06cbc1543@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-2-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Layer 3 hardware stats cannot be used when the underlying interfaces are
veth pairs, resulting in failures:
# ./hw_stats_l3_gre.sh
TEST: ping gre flat [ OK ]
TEST: Test rx packets: [FAIL]
Traffic not reflected in the counter: 0 -> 0
TEST: Test tx packets: [FAIL]
Traffic not reflected in the counter: 0 -> 0
Fix by skipping the test when used with veth pairs.
Fixes: 813f97a26860 ("selftests: forwarding: Add a tunnel-based test for L3 HW stats") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/adc5e40d-d040-a65e-eb26-edf47dac5b02@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-10-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A handful of tests require physical loopbacks to be used instead of veth
pairs. Add a helper that these tests will invoke in order to be skipped
when executed with veth pairs.
Fixes: 64916b57c0b1 ("selftests: forwarding: Add speed and auto-negotiation test") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-7-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3bcbc20942db ("selftests/rseq: Play nice with binaries statically
linked against glibc 2.35+") which is now in Linus' tree introduced uses
of __weak but did nothing to ensure that a definition is provided for it
resulting in build failures for the rseq tests:
rseq.c:41:1: error: unknown type name '__weak'
__weak ptrdiff_t __rseq_offset;
^
rseq.c:41:17: error: expected ';' after top level declarator
__weak ptrdiff_t __rseq_offset;
^
;
rseq.c:42:1: error: unknown type name '__weak'
__weak unsigned int __rseq_size;
^
rseq.c:43:1: error: unknown type name '__weak'
__weak unsigned int __rseq_flags;
Fix this by using the definition from tools/include compiler.h.
Fixes: 3bcbc20942db ("selftests/rseq: Play nice with binaries statically linked against glibc 2.35+") Signed-off-by: Mark Brown <broonie@kernel.org>
Message-Id: <20230804-kselftest-rseq-build-v1-1-015830b66aa9@kernel.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error: #200/79 sockmap_listen/sockmap VSOCK test_vsock_redir
Error: #200/79 sockmap_listen/sockmap VSOCK test_vsock_redir
./test_progs:vsock_unix_redir_connectible:1506: egress: write: Transport endpoint is not connected
vsock_unix_redir_connectible:FAIL:1506
./test_progs:vsock_unix_redir_connectible:1506: ingress: write: Transport endpoint is not connected
vsock_unix_redir_connectible:FAIL:1506
./test_progs:vsock_unix_redir_connectible:1506: egress: write: Transport endpoint is not connected
vsock_unix_redir_connectible:FAIL:1506
./test_progs:vsock_unix_redir_connectible:1514: ingress: recv() err, errno=11
vsock_unix_redir_connectible:FAIL:1514
./test_progs:vsock_unix_redir_connectible:1518: ingress: vsock socket map failed, a != b
vsock_unix_redir_connectible:FAIL:1518
./test_progs:vsock_unix_redir_connectible:1525: ingress: want pass count 1, have 0
It’s because the recv(... MSG_DONTWAIT) syscall in the test case is
called before the queued work sk_psock_backlog() in the kernel finishes
executing. So the data to be read is still queued in psock->ingress_skb
and cannot be read by the user program. Therefore, the non-blocking
recv() reads nothing and reports an EAGAIN error.
So replace recv(... MSG_DONTWAIT) with xrecv_nonblock(), which calls
select() to wait for data to be readable or timeout before calls recv().
Fixes: d61bd8c1fd02 ("selftests/bpf: add a test case for vsock sockmap") Signed-off-by: Xu Kuohai <xukuohai@huawei.com> Link: https://lore.kernel.org/r/20230804073740.194770-4-xukuohai@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log