On some systems amd_pinconf_set() is called with parameters
0x8 (PIN_CONFIG_DRIVE_PUSH_PULL) or 0x14 (PIN_CONFIG_PERSIST_STATE)
which are not supported by pinctrl-amd.
Don't show an err message when called with an invalid parameter,
downgrade this to debug instead.
Cc: stable@vger.kernel.org # 6.1 Fixes: 635a750d958e1 ("pinctrl: amd: Use amd_pinconf_set() for all config options") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20230717201652.17168-1-mario.limonciello@amd.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According the "USB Type-C Port Controller Interface Specification v2.0"
the TCPC sets the fault status register bit-7
(AllRegistersResetToDefault) once the registers have been reset to
their default values.
This triggers an alert(-irq) on PTN5110 devices albeit we do mask the
fault-irq, which may cause a kernel hang. Fix this generically by writing
a one to the corresponding bit-7.
A syzbot stress test using a corrupted disk image reported that
mark_buffer_dirty() called from __nilfs_mark_inode_dirty() or
nilfs_palloc_commit_alloc_entry() may output a kernel warning, and can
panic if the kernel is booted with panic_on_warn.
This is because nilfs2 keeps buffer pointers in local structures for some
metadata and reuses them, but such buffers may be forcibly discarded by
nilfs_clear_dirty_page() in some critical situations.
This issue is reported to appear after commit 28a65b49eb53 ("nilfs2: do
not write dirty data after degenerating to read-only"), but the issue has
potentially existed before.
Fix this issue by checking the uptodate flag when attempting to reuse an
internally held buffer, and reloading the metadata instead of reusing the
buffer if the flag was lost.
Link: https://lkml.kernel.org/r/20230818131804.7758-1-konishi.ryusuke@gmail.com Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+cdfcae656bac88ba0e2d@syzkaller.appspotmail.com Closes: https://lkml.kernel.org/r/0000000000003da75f05fdeffd12@google.com Fixes: 8c26c4e2694a ("nilfs2: fix issue with flush kernel thread after remount in RO mode because of driver's internal error or metadata corruption") Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> # 3.10+ Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pipe cpumask used to serialize opens between the main and percpu
trace pipes is not zeroed or initialized. This can result in
spurious -EBUSY returns if underlying memory is not fully zeroed.
This has been observed by immediate failure to read the main
trace_pipe file on an otherwise newly booted and idle system:
# cat /sys/kernel/debug/tracing/trace_pipe
cat: /sys/kernel/debug/tracing/trace_pipe: Device or resource busy
Zero the allocation of pipe_cpumask to avoid the problem.
Link: https://lore.kernel.org/linux-trace-kernel/20230831125500.986862-1-bfoster@redhat.com Cc: stable@vger.kernel.org Fixes: c2489bb7e6be ("tracing: Introduce pipe_cpumask to avoid race on trace_pipes") Reviewed-by: Zheng Yejian <zhengyejian1@huawei.com> Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Brian Foster <bfoster@redhat.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When partner does not support get_status message, tcpm right now
responds with soft reset message. This causes PD renegotiation to
happen and resets PPS link. Avoid soft resetting the link when
partner does not support get_status message to mitigate PPS resets.
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
The operating-performance-point vote needs to be dropped when shutting
down the port to avoid wasting power by keeping resources like power
domains in an unnecessarily high performance state (e.g. when a UART
connected Bluetooth controller is not in use).
Fixes: a5819b548af0 ("tty: serial: qcom_geni_serial: Use OPP API to set clk/perf state") Cc: stable@vger.kernel.org # 5.9 Cc: Rajendra Nayak <quic_rjendra@quicinc.com> Cc: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org> Link: https://lore.kernel.org/r/20230714130214.14552-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a function is using functions from mac80211 to free an skb then it
should do it consistently and not switch to the generic dev_kfree_skb_any
(or similar functions). Otherwise (like in the error handlers), mac80211
will will not be aware of the freed skb and thus not clean up related
information in its internal data structures.
Not doing so lead in the past to filled up structure which then prevented
new clients to connect.
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Fixes: 6257c702264c ("wifi: ath11k: fix tx status reporting in encap offload mode") Cc: stable@vger.kernel.org Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230802-ath11k-ack_status_leak-v2-2-c0af729d6229@narfation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a station idles for a long time, hostapd will try to send a QoS Null
frame to the station as "poll". NL80211_CMD_PROBE_CLIENT is used for this
purpose. And the skb will be added to ack_status_frame - waiting for a
completion via ieee80211_report_ack_skb().
But when the peer was already removed before the tx_complete arrives, the
peer will be missing. And when using dev_kfree_skb_any (instead of going
through mac80211), the entry will stay inside ack_status_frames. This IDR
will therefore run full after 8K request were generated for such clients.
At this point, the access point will then just stall and not allow any new
clients because idr_alloc() for ack_status_frame will fail.
ieee80211_free_txskb() on the other hand will (when required) call
ieee80211_report_ack_skb() and make sure that (when required) remove the
entry from the ack_status_frame.
Fixes: 6257c702264c ("wifi: ath11k: fix tx status reporting in encap offload mode") Fixes: 94739d45c388 ("ath11k: switch to using ieee80211_tx_status_ext()") Cc: stable@vger.kernel.org Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230802-ath11k-ack_status_leak-v2-1-c0af729d6229@narfation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After rtw_usb_alloc_rx_bufs() has been called rx urbs have been
allocated and must be freed in the error path. After rtw_usb_init_rx()
has been called they are submitted, so they also must be killed.
Add these forgotten steps to the probe error path.
Besides the lost memory this also fixes a problem when the driver
fails to download the firmware in rtw_chip_info_setup(). In this
case it can happen that the completion of the rx urbs handler runs
at a time when we already freed our data structures resulting in
a kernel crash.
Fixes: a82dfd33d123 ("wifi: rtw88: Add common USB chip support") Cc: stable@vger.kernel.org Reported-by: Ilgaz Öcal <ilgaz@ilgaz.gen.tr> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230823075021.588596-1-s.hauer@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
txs may be dropped if the frame is aggregated in AMSDU. When the problem
shows up, some SKBs would be hold in driver to cause network stopped
temporarily. Even if the problem can be recovered by txs timeout handling,
mt7921 still need to disable txs in AMSDU to avoid this issue.
Cc: stable@vger.kernel.org Fixes: 163f4d22c118 ("mt76: mt7921: add MAC support") Reviewed-by: Shayne Chen <shayne.chen@mediatek.com> Signed-off-by: Deren Wu <deren.wu@mediatek.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In probe function, request_firmware_nowait() is called to load firmware
asynchronously. At completion of firmware loading, register_netdev() is
called. However, a mutex needed by netdev is initialized after the call
to request_firmware_nowait(). Consequently, it can happen that
register_netdev() is called before the driver is ready.
Move the mutex initialization into r8712_init_drv_sw(), which is called
before request_firmware_nowait().
Reported-by: syzbot+b08315e8cf5a78eed03c@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-staging/000000000000d9d4560601b8e0d7@google.com/T/#u Fixes: 8c213fa59199 ("staging: r8712u: Use asynchronous firmware loading") Cc: stable <stable@kernel.org> Signed-off-by: Nam Cao <namcaov@gmail.com> Link: https://lore.kernel.org/r/20230731110620.116562-1-namcaov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the EKR battery remains even after we stop getting information
from the device. This can lead to a stale battery persisting indefinitely
in userspace.
The remote sends a heartbeat every 10 seconds. Delete the battery if we
miss two heartbeats (after 21 seconds). Restore the battery once we see
a heartbeat again.
Signed-off-by: Aaron Skomra <skomra@gmail.com> Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com> Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com> Fixes: 9f1015d45f62 ("HID: wacom: EKR: attach the power_supply on first connection") CC: stable@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current driver, the value of tuning parameter will not take effect
if samsung,picophy-* is assigned as 0. Because 0 is also a valid value
acccording to the description of USB_PHY_CFG1 register, this will improve
the logic to let it work.
Fixes: 58a3cefb3840 ("usb: chipidea: imx: add two samsung picophy parameters tuning implementation")
cc: <stable@vger.kernel.org> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20230627112126.1882666-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device connected to usb otg port of GXL-based boards can not be
recognised after resumption, doesn't recover even if disconnect and
reconnect the device. dmesg shows it disconnects during resumption.
[ 41.492911] usb 1-2: USB disconnect, device number 3
[ 41.499346] usb 1-2: unregistering device
[ 41.511939] usb 1-2: unregistering interface 1-2:1.0
Calling usb_post_init() will fix this issue, and it's tested and
verified on libretech's aml-s905x-cc board.
Cc: stable@vger.kernel.org # v5.8+ Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue") Signed-off-by: Luke Lu <luke.lu@libre.computer> Acked-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20230809212911.18903-1-luke.lu@libre.computer Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been reports of USB-audio driver spewing errors at the
probe time on a few devices like Jabra and Logitech. The suggested
fix there couldn't be applied as is, unfortunately, because it'll
likely break other devices.
But, the patch suggested an interesting point: looking at the current
init code in stream.c, one may notice that it does initialize
differently from the device setup in endpoint.c. Namely, for UAC1, we
should call snd_usb_init_pitch() and snd_usb_init_sample_rate() after
setting the interface, while the init sequence at parsing calls them
before setting the interface blindly.
This patch changes the init sequence at parsing for UAC1 (and other
devices that need a similar behavior) to be aligned with the rest of
the code, setting the interface at first. And, this fixes the
long-standing problems on a few UAC1 devices like Jabra / Logitech,
as reported, too.
It has recently come to my attention that nvidia is circumventing the
protection added in 262e6ae7081d ("modules: inherit
TAINT_PROPRIETARY_MODULE") by importing exports from their proprietary
modules into an allegedly GPL licensed module and then rexporting them.
Given that symbol_get was only ever intended for tightly cooperating
modules using very internal symbols it is logical to restrict it to
being used on EXPORT_SYMBOL_GPL and prevent nvidia from costly DMCA
Circumvention of Access Controls law suites.
All symbols except for four used through symbol_get were already exported
as EXPORT_SYMBOL_GPL, and the remaining four ones were switched over in
the preparation patches.
ds1685_rtc_poweroff is only used externally via symbol_get, which was
only ever intended for very internal symbols like this one. Use
EXPORT_SYMBOL_GPL for it so that symbol_get can enforce only being used
on EXPORT_SYMBOL_GPL symbols.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Joshua Kinard <kumba@gentoo.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
enetc_phc_index is only used via symbol_get, which was only ever
intended for very internal symbols like this one. Use EXPORT_SYMBOL_GPL
for it so that symbol_get can enforce only being used on
EXPORT_SYMBOL_GPL symbols.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
au1xmmc is split somewhat awkwardly into the main mmc subsystem driver,
and callbacks in platform_data that sit under arch/mips/ and are
always built in. The latter than call mmc_detect_change through
symbol_get. Remove the use of symbol_get by requiring the driver
to be built in. In the future the interrupt handlers for card
insert/eject detection should probably be moved into the main driver,
and which point it can be built modular again.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Manuel Lauss <manuel.lauss@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
[mcgrof: squashed in depends on MMC=y suggested by Arnd] Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spitz board file uses the obscure symbol_get() function
to optionally call a function from sharpsl_pm.c if that is
built. However, the two files are always built together
these days, and have been for a long time, so this can
be changed to a normal function call.
Link: https://lore.kernel.org/lkml/20230731162639.GA9441@lst.de/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If authblob->SessionKey.Length is bigger than session key
size(CIFS_KEY_SIZE), slub overflow can happen in key exchange codes.
cifs_arc4_crypt copy to session key array from SessionKey from client.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21940 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ->DataOffset of create context is 0, DataBuffer size is not correctly
validated. This patch change wrong validation code and consider tag
length in request.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21824 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was accidentally fixed up in commit e4c1cf523d82 but we can't
take the full change due to other dependancy issues, so here is just
the actual bugfix that is needed.
[Background]
keltargw reported an issue [1] that with mmaped I/Os, sometimes the
tail of the last page (after file ends) is not filled with zeroes.
The root cause is that such tail page could be wrongly selected for
inplace I/Os so the zeroed part will then be filled with compressed
data instead of zeroes.
A simple fix is to avoid doing inplace I/Os for such tail parts,
actually that was already fixed upstream in commit e4c1cf523d82
("erofs: tidy up z_erofs_do_read_page()") by accident.
Kernel test robot reported a kallsyms_test failure when clang lto is
enabled (thin or full) and CONFIG_KALLSYMS_SELFTEST is also enabled.
I can reproduce in my local environment with the following error message
with thin lto:
[ 1.877897] kallsyms_selftest: Test for 1750th symbol failed: (tsc_cs_mark_unstable) addr=ffffffff81038090
[ 1.877901] kallsyms_selftest: abort
It appears that commit 8cc32a9bbf29 ("kallsyms: strip LTO-only suffixes
from promoted global functions") caused the failure. Commit 8cc32a9bbf29
changed cleanup_symbol_name() based on ".llvm." instead of '.' where
".llvm." is appended to a before-lto-optimization local symbol name.
We need to propagate such knowledge in kallsyms_selftest.c as well.
Further more, compare_symbol_name() in kallsyms.c needs change as well.
In scripts/kallsyms.c, kallsyms_names and kallsyms_seqs_of_names are used
to record symbol names themselves and index to symbol names respectively.
For example:
kallsyms_names:
...
__amd_smn_rw._entry <== seq 1000
__amd_smn_rw._entry.5 <== seq 1001
__amd_smn_rw.llvm.<hash> <== seq 1002
...
kallsyms_seqs_of_names are sorted based on cleanup_symbol_name() through, so
the order in kallsyms_seqs_of_names actually has
index 1000: seq 1002 <== __amd_smn_rw.llvm.<hash> (actual symbol comparison using '__amd_smn_rw')
index 1001: seq 1000 <== __amd_smn_rw._entry
index 1002: seq 1001 <== __amd_smn_rw._entry.5
Let us say at a particular point, at index 1000, symbol '__amd_smn_rw.llvm.<hash>'
is comparing to '__amd_smn_rw._entry' where '__amd_smn_rw._entry' is the one to
search e.g., with function kallsyms_on_each_match_symbol(). The current implementation
will find out '__amd_smn_rw._entry' is less than '__amd_smn_rw.llvm.<hash>' and
then continue to search e.g., index 999 and never found a match although the actual
index 1001 is a match.
To fix this issue, let us do cleanup_symbol_name() first and then do comparison.
In the above case, comparing '__amd_smn_rw' vs '__amd_smn_rw._entry' and
'__amd_smn_rw._entry' being greater than '__amd_smn_rw', the next comparison will
be > index 1000 and eventually index 1001 will be hit an a match is found.
For any symbols not having '.llvm.' substr, there is no functionality change
for compare_symbol_name().
Fixes: 8cc32a9bbf29 ("kallsyms: strip LTO-only suffixes from promoted global functions") Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202308232200.1c932a90-oliver.sang@intel.com Signed-off-by: Yonghong Song <yonghong.song@linux.dev> Reviewed-by: Song Liu <song@kernel.org> Reviewed-by: Zhen Lei <thunder.leizhen@huawei.com> Link: https://lore.kernel.org/r/20230825034659.1037627-1-yonghong.song@linux.dev Cc: stable@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the parisc architecture, lockdep reports for all static objects which
are in the __initdata section (e.g. "setup_done" in devtmpfs,
"kthreadd_done" in init/main.c) this warning:
INFO: trying to register non-static key.
The warning itself is wrong, because those objects are in the __initdata
section, but the section itself is on parisc outside of range from
_stext to _end, which is why the static_obj() functions returns a wrong
answer.
While fixing this issue, I noticed that the whole existing check can
be simplified a lot.
Instead of checking against the _stext and _end symbols (which include
code areas too) just check for the .data and .bss segments (since we check a
data object). This can be done with the existing is_kernel_core_data()
macro.
In addition objects in the __initdata section can be checked with
init_section_contains(), and is_kernel_rodata() allows keys to be in the
_ro_after_init section.
This partly reverts and simplifies commit bac59d18c701 ("x86/setup: Fix static
memory detection").
IPv6 inet sockets are supposed to have a "struct ipv6_pinfo"
field at the end of their definition, so that inet6_sk_generic()
can derive from socket size the offset of the "struct ipv6_pinfo".
This is very fragile, and prevents adding bigger alignment
in sockets, because inet6_sk_generic() does not work
if the compiler adds padding after the ipv6_pinfo component.
We are currently working on a patch series to reorganize
TCP structures for better data locality and found issues
similar to the one fixed in commit f5d547676ca0
("tcp: fix tcp_inet6_sk() for 32bit kernels")
Alternative would be to force an alignment on "struct ipv6_pinfo",
greater or equal to __alignof__(any ipv6 sock) to ensure there is
no padding. This does not look great.
v2: fix typo in mptcp_proto_v6_init() (Paolo)
Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Chao Wu <wwchao@google.com> Cc: Wei Wang <weiwan@google.com> Cc: Coco Li <lixiaoyan@google.com> Cc: YiFei Zhu <zhuyifei@google.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
However, continuous physical memory does not seem to be required in
module_zstd_decompress(), so use vmalloc() instead, to prevent the
warning and avoid potential failures at loading compressed modules.
Fixes: 169a58ad824d ("module/decompress: Support zstd in-kernel decompression") Signed-off-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today module_frob_arch_sections() spots init sections from their
'init' prefix, and uses this to keep the init PLTs separate from the rest.
get_module_plt() uses within_module_init() to determine if a
location is in the init text or not, but this depends on whether
core code thought this was an init section.
Naturally the logic is different.
module_init_layout_section() groups the init and exit text together if
module unloading is disabled, as the exit code will never run. The result
is kernels with this configuration can't load all their modules because
there are not enough PLTs for the combined init+exit section.
A previous patch exposed module_init_layout_section(), use that so the
logic is the same.
Fixes: 055f23b74b20 ("module: check for exit sections in layout_sections() instead of module_init_section()") Cc: stable@vger.kernel.org Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today module_frob_arch_sections() spots init sections from their
'init' prefix, and uses this to keep the init PLTs separate from the rest.
module_emit_plt_entry() uses within_module_init() to determine if a
location is in the init text or not, but this depends on whether
core code thought this was an init section.
Naturally the logic is different.
module_init_layout_section() groups the init and exit text together if
module unloading is disabled, as the exit code will never run. The result
is kernels with this configuration can't load all their modules because
there are not enough PLTs for the combined init+exit section.
module_init_layout_section() choses whether the core module loader
considers a section as init or not. This affects the placement of the
exit section when module unloading is disabled. This code will never run,
so it can be free()d once the module has been initialised.
arm and arm64 need to count the number of PLTs they need before applying
relocations based on the section name. The init PLTs are stored separately
so they can be free()d. arm and arm64 both use within_module_init() to
decide which list of PLTs to use when applying the relocation.
Because within_module_init()'s behaviour changes when module unloading
is disabled, both architecture would need to take this into account when
counting the PLTs.
Today neither architecture does this, meaning when module unloading is
disabled there are insufficient PLTs in the init section to load some
modules, resulting in warnings:
| WARNING: CPU: 2 PID: 51 at arch/arm64/kernel/module-plts.c:99 module_emit_plt_entry+0x184/0x1cc
| Modules linked in: crct10dif_common
| CPU: 2 PID: 51 Comm: modprobe Not tainted 6.5.0-rc4-yocto-standard-dirty #15208
| Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
| pstate: 20400005 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
| pc : module_emit_plt_entry+0x184/0x1cc
| lr : module_emit_plt_entry+0x94/0x1cc
| sp : ffffffc0803bba60
[...]
| Call trace:
| module_emit_plt_entry+0x184/0x1cc
| apply_relocate_add+0x2bc/0x8e4
| load_module+0xe34/0x1bd4
| init_module_from_file+0x84/0xc0
| __arm64_sys_finit_module+0x1b8/0x27c
| invoke_syscall.constprop.0+0x5c/0x104
| do_el0_svc+0x58/0x160
| el0_svc+0x38/0x110
| el0t_64_sync_handler+0xc0/0xc4
| el0t_64_sync+0x190/0x194
Instead of duplicating module_init_layout_section()s logic, expose it.
Reported-by: Adam Johnston <adam.johnston@arm.com> Fixes: 055f23b74b20 ("module: check for exit sections in layout_sections() instead of module_init_section()") Cc: stable@vger.kernel.org Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `nocrt` module parameter has no code associated with it and does
nothing. As `crt=-1` has same functionality as what nocrt should be
doing drop `nocrt` and associated documentation.
This should fix a quirk for Gigabyte GA-7ZX that used `nocrt` and
thus didn't function properly.
Fixes: 8c99fdce3078 ("ACPI: thermal: set "thermal.nocrt" via DMI on Gigabyte GA-7ZX") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 27 Aug 2023 14:33:54 +0000 (07:33 -0700)]
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small driver fixes and one larger unused function set removal in
the raid class (so no external impact)"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: snic: Fix double free in snic_tgt_create()
scsi: core: raid_class: Remove raid_component_add()
scsi: ufs: ufs-qcom: Clear qunipro_g4_sel for HW major version > 5
scsi: ufs: mcq: Fix the search/wrap around logic
Linus Torvalds [Sat, 26 Aug 2023 17:57:29 +0000 (10:57 -0700)]
Merge tag 'x86-urgent-2023-08-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Fix an FPU invalidation bug on exec(), and fix a performance
regression due to a missing setting of X86_FEATURE_OSXSAVE"
* tag 'x86-urgent-2023-08-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Set X86_FEATURE_OSXSAVE feature after enabling OSXSAVE in CR4
x86/fpu: Invalidate FPU state correctly on exec()
Linus Torvalds [Sat, 26 Aug 2023 17:34:29 +0000 (10:34 -0700)]
Merge tag 'irq-urgent-2023-08-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A last minute fix for a regression introduced in the v6.5 merge
window.
The conversion of the software based interrupt resend mechanism to
hlist missed to add a check whether the descriptor is already enqueued
and dropped the interrupt descriptor lookup for nested interrupts.
The missing check whether the descriptor is already queued causes
hlist corruption and can be observed in the wild. The dropped parent
descriptor lookup has not yet caused problems, but it would result in
stale interrupt line in the worst case.
Add the missing enqueued check and bring the descriptor lookup back to
cure this"
* tag 'irq-urgent-2023-08-26' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix software resend lockup and nested resend
Linus Torvalds [Sat, 26 Aug 2023 17:28:52 +0000 (10:28 -0700)]
Merge tag 'loongarch-fixes-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix a ptrace bug, a hw_breakpoint bug, some build errors/warnings and
some trivial cleanups"
* tag 'loongarch-fixes-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: Fix hw_breakpoint_control() for watchpoints
LoongArch: Ensure FP/SIMD registers in the core dump file is up to date
LoongArch: Put the body of play_dead() into arch_cpu_idle_dead()
LoongArch: Add identifier names to arguments of die() declaration
LoongArch: Return earlier in die() if notify_die() returns NOTIFY_STOP
LoongArch: Do not kill the task in die() if notify_die() returns NOTIFY_STOP
LoongArch: Remove <asm/export.h>
LoongArch: Replace #include <asm/export.h> with #include <linux/export.h>
LoongArch: Remove unneeded #include <asm/export.h>
LoongArch: Replace -ffreestanding with finer-grained -fno-builtin's
LoongArch: Remove redundant "source drivers/firmware/Kconfig"
Johan Hovold [Sat, 26 Aug 2023 15:40:04 +0000 (17:40 +0200)]
genirq: Fix software resend lockup and nested resend
The switch to using hlist for managing software resend of interrupts
broke resend in at least two ways:
First, unconditionally adding interrupt descriptors to the resend list can
corrupt the list when the descriptor in question has already been
added. This causes the resend tasklet to loop indefinitely with interrupts
disabled as was recently reported with the Lenovo ThinkPad X13s after
threaded NAPI was disabled in the ath11k WiFi driver.
This bug is easily fixed by restoring the old semantics of irq_sw_resend()
so that it can be called also for descriptors that have already been marked
for resend.
Second, the offending commit also broke software resend of nested
interrupts by simply discarding the code that made sure that such
interrupts are retriggered using the parent interrupt.
Add back the corresponding code that adds the parent descriptor to the
resend list.
Huacai Chen [Sat, 26 Aug 2023 14:21:57 +0000 (22:21 +0800)]
LoongArch: Fix hw_breakpoint_control() for watchpoints
In hw_breakpoint_control(), encode_ctrl_reg() has already encoded the
MWPnCFG3_LoadEn/MWPnCFG3_StoreEn bits in info->ctrl. We don't need to
add (1 << MWPnCFG3_LoadEn | 1 << MWPnCFG3_StoreEn) unconditionally.
Otherwise we can't set read watchpoint and write watchpoint separately.
Huacai Chen [Sat, 26 Aug 2023 14:21:57 +0000 (22:21 +0800)]
LoongArch: Ensure FP/SIMD registers in the core dump file is up to date
This is a port of commit 379eb01c21795edb4c ("riscv: Ensure the value
of FP registers in the core dump file is up to date").
The values of FP/SIMD registers in the core dump file come from the
thread.fpu. However, kernel saves the FP/SIMD registers only before
scheduling out the process. If no process switch happens during the
exception handling, kernel will not have a chance to save the latest
values of FP/SIMD registers. So it may cause their values in the core
dump file incorrect. To solve this problem, force fpr_get()/simd_get()
to save the FP/SIMD registers into the thread.fpu if the target task
equals the current task.
Helge Deller [Fri, 25 Aug 2023 19:50:33 +0000 (21:50 +0200)]
lib/clz_ctz.c: Fix __clzdi2() and __ctzdi2() for 32-bit kernels
The gcc compiler translates on some architectures the 64-bit
__builtin_clzll() function to a call to the libgcc function __clzdi2(),
which should take a 64-bit parameter on 32- and 64-bit platforms.
But in the current kernel code, the built-in __clzdi2() function is
defined to operate (wrongly) on 32-bit parameters if BITS_PER_LONG ==
32, thus the return values on 32-bit kernels are in the range from
[0..31] instead of the expected [0..63] range.
This patch fixes the in-kernel functions __clzdi2() and __ctzdi2() to
take a 64-bit parameter on 32-bit kernels as well, thus it makes the
functions identical for 32- and 64-bit kernels.
This bug went unnoticed since kernel 3.11 for over 10 years, and here
are some possible reasons for that:
a) Some architectures have assembly instructions to count the bits and
which are used instead of calling __clzdi2(), e.g. on x86 the bsr
instruction and on ppc cntlz is used. On such architectures the
wrong __clzdi2() implementation isn't used and as such the bug has
no effect and won't be noticed.
b) Some architectures link to libgcc.a, and the in-kernel weak
functions get replaced by the correct 64-bit variants from libgcc.a.
c) __builtin_clzll() and __clzdi2() doesn't seem to be used in many
places in the kernel, and most likely only in uncritical functions,
e.g. when printing hex values via seq_put_hex_ll(). The wrong return
value will still print the correct number, but just in a wrong
formatting (e.g. with too many leading zeroes).
d) 32-bit kernels aren't used that much any longer, so they are less
tested.
A trivial testcase to verify if the currently running 32-bit kernel is
affected by the bug is to look at the output of /proc/self/maps:
Here the kernel uses a correct implementation of __clzdi2():
Linus Torvalds [Fri, 25 Aug 2023 18:44:43 +0000 (11:44 -0700)]
Merge tag 'mm-hotfixes-stable-2023-08-25-11-07' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"18 hotfixes. 13 are cc:stable and the remainder pertain to post-6.4
issues or aren't considered suitable for a -stable backport"
* tag 'mm-hotfixes-stable-2023-08-25-11-07' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
shmem: fix smaps BUG sleeping while atomic
selftests: cachestat: catch failing fsync test on tmpfs
selftests: cachestat: test for cachestat availability
maple_tree: disable mas_wr_append() when other readers are possible
madvise:madvise_free_pte_range(): don't use mapcount() against large folio for sharing check
madvise:madvise_free_huge_pmd(): don't use mapcount() against large folio for sharing check
madvise:madvise_cold_or_pageout_pte_range(): don't use mapcount() against large folio for sharing check
mm: multi-gen LRU: don't spin during memcg release
mm: memory-failure: fix unexpected return value in soft_offline_page()
radix tree: remove unused variable
mm: add a call to flush_cache_vmap() in vmap_pfn()
selftests/mm: FOLL_LONGTERM need to be updated to 0x100
nilfs2: fix general protection fault in nilfs_lookup_dirty_data_buffers()
mm/gup: handle cont-PTE hugetlb pages correctly in gup_must_unshare() via GUP-fast
selftests: cgroup: fix test_kmem_basic less than error
mm: enable page walking API to lock vmas during the walk
smaps: use vm_normal_page_pmd() instead of follow_trans_huge_pmd()
mm/gup: reintroduce FOLL_NUMA as FOLL_HONOR_NUMA_FAULT
Linus Torvalds [Fri, 25 Aug 2023 16:29:47 +0000 (09:29 -0700)]
Merge tag 'riscv-for-linus-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"This is obviously not ideal, particularly for something this late in
the cycle.
Unfortunately we found some uABI issues in the vector support while
reviewing the GDB port, which has triggered a revert -- probably a
good sign we should have reviewed GDB before merging this, I guess I
just dropped the ball because I was so worried about the context
extension and libc suff I forgot. Hence the late revert.
There's some risk here as we're still exposing the vector context for
signal handlers, but changing that would have meant reverting all of
the vector support. The issues we've found so far have been fixed
already and they weren't absolute showstoppers, so we're essentially
just playing it safe by holding ptrace support for another release (or
until we get through a proper userspace code review).
Summary:
- The vector ucontext extension has been extended with vlenb
- The vector registers ELF core dump note type has been changed to
avoid aliasing with the CSR type used in embedded systems
- Support for accessing vector registers via ptrace() has been
reverted
- Another build fix for the ISA spec changes around Zifencei/Zicsr
that manifests on some systems built with binutils-2.37 and
gcc-11.2"
* tag 'riscv-for-linus-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix build errors using binutils2.37 toolchains
RISC-V: vector: export VLENB csr in __sc_riscv_v_state
RISC-V: Remove ptrace support for vectors
Linus Torvalds [Fri, 25 Aug 2023 16:18:22 +0000 (09:18 -0700)]
Merge tag 'gpio-fixes-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- fix an irq mapping leak in gpio-sim
- associate the GPIO device's software node with the irq domain in
gpio-sim
* tag 'gpio-fixes-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: sim: pass the GPIO device's software node to irq domain
gpio: sim: dispose of irq mappings before destroying the irq_sim domain
Linus Torvalds [Fri, 25 Aug 2023 16:10:16 +0000 (09:10 -0700)]
Merge tag 'pinctrl-v6.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are some Renesas and AMD driver fixes, the AMD fix affects
important laptops in the wild so this one is pretty important. It
seems a bit tough to get this right.
- Fix DT parsing and related locking in the Renesas driver.
- Fix wakeup IRQs in the AMD driver once again. Really tricky this
one"
* tag 'pinctrl-v6.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: amd: Mask wake bits on probe again
pinctrl: renesas: rza2: Add lock around pinctrl_generic{{add,remove}_group,{add,remove}_function}
pinctrl: renesas: rzv2m: Fix NULL pointer dereference in rzv2m_dt_subnode_to_map()
pinctrl: renesas: rzg2l: Fix NULL pointer dereference in rzg2l_dt_subnode_to_map()
Linus Torvalds [Fri, 25 Aug 2023 15:48:14 +0000 (08:48 -0700)]
Merge tag 'sound-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the last bits for 6.5. It's slightly higher LOCs than
wished, but it doesn't look scary.
The biggest change is MAINTAINERS update for TI; it's good to have the
update before the final release, so that people can contact to the
right persons for bug reports (which shouldn't happen of course!)
The rest are all device-specific fixes and quirks, most for various
ASoC platforms"
* tag 'sound-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: amd: yc: Fix a non-functional mic on Lenovo 82SJ
ALSA: ymfpci: Fix the missing snd_card_free() call at probe error
ASoC: cs35l41: Correct amp_gain_tlv values
ASoC: amd: yc: Add VivoBook Pro 15 to quirks list for acp6x
ASoC: tas2781: fixed register access error when switching to other chips
ASoC: cs35l56: Add an ACPI match table
ASoC: cs35l56: Read firmware uuid from a device property instead of _SUB
ASoC: SOF: ipc4-pcm: fix possible null pointer deference
MAINTAINERS: Add entries for TEXAS INSTRUMENTS ASoC DRIVERS
Tiezhu Yang [Fri, 25 Aug 2023 15:40:38 +0000 (23:40 +0800)]
LoongArch: Put the body of play_dead() into arch_cpu_idle_dead()
The initial aim is to silence the following objtool warning:
arch/loongarch/kernel/process.o: warning: objtool: arch_cpu_idle_dead() falls through to next function start_thread()
According to tools/objtool/Documentation/objtool.txt, this is because
the last instruction of arch_cpu_idle_dead() is a call to a noreturn
function play_dead(). In order to silence the warning, one simple way
is to add the noreturn function play_dead() to objtool's hard-coded
global_noreturns array, that is to say, just put "NORETURN(play_dead)"
into tools/objtool/noreturns.h, it works well.
But I noticed that play_dead() is only defined once and only called by
arch_cpu_idle_dead(), so put the body of play_dead() into the caller
arch_cpu_idle_dead(), then remove the noreturn function play_dead() is
an alternative way which can reduce the overhead of the function call
at the same time.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Tiezhu Yang [Fri, 25 Aug 2023 15:40:26 +0000 (23:40 +0800)]
LoongArch: Add identifier names to arguments of die() declaration
Add identifier names to arguments of die() declaration in ptrace.h
to fix the following checkpatch warnings:
WARNING: function definition argument 'const char *' should also have an identifier name
WARNING: function definition argument 'struct pt_regs *' should also have an identifier name
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Tiezhu Yang [Fri, 25 Aug 2023 15:40:26 +0000 (23:40 +0800)]
LoongArch: Return earlier in die() if notify_die() returns NOTIFY_STOP
After the call to oops_exit(), it should not panic or execute
the crash kernel if the oops is to be suppressed.
Suggested-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Tiezhu Yang [Fri, 25 Aug 2023 15:40:26 +0000 (23:40 +0800)]
LoongArch: Do not kill the task in die() if notify_die() returns NOTIFY_STOP
If notify_die() returns NOTIFY_STOP, honor the return value from the
handler chain invocation in die() and return without killing the task
as, through a debugger, the fault may have been fixed. It makes sense
even if ignoring the event will make the system unstable: by allowing
access through a debugger it has been compromised already anyway. It
makes our port consistent with x86, arm64, riscv and csky.
Commit 20c0d2d44029 ("[PATCH] i386: pass proper trap numbers to die
chain handlers") may be the earliest of similar changes.
WANG Xuerui [Fri, 25 Aug 2023 15:40:26 +0000 (23:40 +0800)]
LoongArch: Replace -ffreestanding with finer-grained -fno-builtin's
As explained by Nick in the original issue: the kernel usually does a
good job of providing library helpers that have similar semantics as
their ordinary userspace libc equivalents, but -ffreestanding disables
such libcall optimization and other related features in the compiler,
which can lead to unexpected things such as CONFIG_FORTIFY_SOURCE not
working (!).
However, due to the desire for better control over unaligned accesses
with respect to CONFIG_ARCH_STRICT_ALIGN, and also for avoiding the
GCC bug https://gcc.gnu.org/PR109465, we do want to still disable
optimizations for the memory libcalls (memcpy, memmove and memset for
now). Use finer-grained -fno-builtin-* toggles to achieve this without
losing source fortification and other libcall optimizations.
Closes: https://github.com/ClangBuiltLinux/linux/issues/1897 Reported-by: Nathan Chancellor <nathan@kernel.org> Suggested-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: WANG Xuerui <git@xen0n.name> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
In drivers/Kconfig, drivers/firmware/Kconfig is sourced for all ports so
there is no need to source it in the port-specific Kconfig file. And
sourcing it here also caused the "Firmware Drivers" menu appeared two
times: one in the "Device Drivers" menu, another in the toplevel menu.
This is really puzzling so remove it.
Reviewed-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Xi Ruoyao <xry111@xry111.site> Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Linus Torvalds [Fri, 25 Aug 2023 15:38:40 +0000 (08:38 -0700)]
Merge tag 'drm-fixes-2023-08-25' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"A bit bigger than I'd care for, but it's mostly a single vmwgfx fix
and a fix for an i915 hotplug probing. Otherwise misc i915, bridge,
panfrost and dma-buf fixes.
core:
- add a HPD poll helper
i915:
- fix regression in i915 polling
- fix docs build warning
- fix DG2 idle power consumption
* tag 'drm-fixes-2023-08-25' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Fix HPD polling, reenabling the output poll work as needed
drm: Add an HPD poll helper to reschedule the poll work
drm/vmwgfx: Fix possible invalid drm gem put calls
drm/vmwgfx: Fix shader stage validation
dma-buf/sw_sync: Avoid recursive lock during fence signal
drm/i915: fix Sphinx indentation warning
drm/i915/dgfx: Enable d3cold at s2idle
drm/display/dp: Fix the DP DSC Receiver cap size
drm/panfrost: Skip speed binning on EOPNOTSUPP
drm: bridge: samsung-dsim: Fix init during host transfer
Linus Torvalds [Fri, 25 Aug 2023 02:39:20 +0000 (19:39 -0700)]
Merge tag 'trace-v6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix ring buffer being permanently disabled due to missed
record_disabled()
Changing the trace cpu mask will disable the ring buffers for the
CPUs no longer in the mask. But it fails to update the snapshot
buffer. If a snapshot takes place, the accounting for the ring buffer
being disabled is corrupted and this can lead to the ring buffer
being permanently disabled.
- Add test case for snapshot and cpu mask working together
- Fix memleak by the function graph tracer not getting closed properly.
The iterator is used to read the ring buffer. When it opens, it calls
the open function of a tracer, and when it is closed, it calls the
close iteration. While a trace is being read, it is still possible to
change the tracer.
If this happens between the function graph tracer and the wakeup
tracer (which uses function graph tracing), the tracers are not
closed properly during when the iterator sees the switch, and the
wakeup function did not initialize its private pointer to NULL, which
is used to know if the function graph tracer was the last tracer. It
could be fooled in thinking it is, but then on exit it does not call
the close function of the function graph tracer to clean up its data.
- Fix synthetic events on big endian machines, by introducing a union
that does the conversions properly.
- Fix synthetic events from printing out the number of elements in the
stacktrace when it shouldn't.
- Fix synthetic events stacktrace to not print a bogus value at the
end.
- Introduce a pipe_cpumask that prevents the trace_pipe files from
being opened by more than one task (file descriptor).
There was a race found where if splice is called, the iter->ent could
become stale and events could be missed. There's no point reading a
producer/consumer file by more than one task as they will corrupt
each other anyway. Add a cpumask that keeps track of the per_cpu
trace_pipe files as well as the global trace_pipe file that prevents
more than one open of a trace_pipe file that represents the same ring
buffer. This prevents the race from happening.
- Fix ftrace samples for arm64 to work with older compilers.
* tag 'trace-v6.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
samples: ftrace: Replace bti assembly with hint for older compiler
tracing: Introduce pipe_cpumask to avoid race on trace_pipes
tracing: Fix memleak due to race between current_tracer and trace
tracing/synthetic: Allocate one additional element for size
tracing/synthetic: Skip first entry for stack traces
tracing/synthetic: Use union instead of casts
selftests/ftrace: Add a basic testcase for snapshot
tracing: Fix cpu buffers unavailable due to 'record_disabled' missed
Zhu Wang [Sat, 19 Aug 2023 08:39:41 +0000 (08:39 +0000)]
scsi: snic: Fix double free in snic_tgt_create()
Commit 41320b18a0e0 ("scsi: snic: Fix possible memory leak if device_add()
fails") fixed the memory leak caused by dev_set_name() when device_add()
failed. However, it did not consider that 'tgt' has already been released
when put_device(&tgt->dev) is called. Remove kfree(tgt) in the error path
to avoid double free of 'tgt' and move put_device(&tgt->dev) after the
removed kfree(tgt) to avoid a use-after-free.
Linus Torvalds [Fri, 25 Aug 2023 02:10:53 +0000 (19:10 -0700)]
Merge tag 'media/v6.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"Fix a potential array out-of-bounds in the mediatek vcodec driver"
* tag 'media/v6.5-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: vcodec: Fix potential array out-of-bounds in encoder queue_setup
The raid_component_add() function was added to the kernel tree via patch
"[SCSI] embryonic RAID class" (2005). Remove this function since it never
has had any callers in the Linux kernel. And also raid_component_release()
is only used in raid_component_add(), so it is also removed.
Signed-off-by: Zhu Wang <wangzhu9@huawei.com> Link: https://lore.kernel.org/r/20230822015254.184270-1-wangzhu9@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Fixes: 04b5b5cb0136 ("scsi: core: Fix possible memory leak if device_add() fails") Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hugh Dickins [Wed, 23 Aug 2023 05:14:47 +0000 (22:14 -0700)]
shmem: fix smaps BUG sleeping while atomic
smaps_pte_hole_lookup() is calling shmem_partial_swap_usage() with page
table lock held: but shmem_partial_swap_usage() does cond_resched_rcu() if
need_resched(): "BUG: sleeping function called from invalid context".
Since shmem_partial_swap_usage() is designed to count across a range, but
smaps_pte_hole_lookup() only calls it for a single page slot, just break
out of the loop on the last or only page, before checking need_resched().
Link: https://lkml.kernel.org/r/6fe3b3ec-abdf-332f-5c23-6a3b3a3b11a9@google.com Fixes: 230100321518 ("mm/smaps: simplify shmem handling of pte holes") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: <stable@vger.kernel.org> [5.16+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Andre Przywara [Mon, 21 Aug 2023 16:05:34 +0000 (17:05 +0100)]
selftests: cachestat: catch failing fsync test on tmpfs
The cachestat kselftest runs a test on a normal file, which is created
temporarily in the current directory. Among the tests it runs there is a
call to fsync(), which is expected to clean all dirty pages used by the
file.
However the tmpfs filesystem implements fsync() as noop_fsync(), so the
call will not even attempt to clean anything when this test file happens
to live on a tmpfs instance. This happens in an initramfs, or when the
current directory is in /dev/shm or sometimes /tmp.
To avoid this test failing wrongly, use statfs() to check which filesystem
the test file lives on. If that is "tmpfs", we skip the fsync() test.
Since the fsync test is only one part of the "normal file" test, we now
execute this twice, skipping the fsync part on the first call. This way
only the second test, including the fsync part, would be skipped.
Link: https://lkml.kernel.org/r/20230821160534.3414911-3-andre.przywara@arm.com Signed-off-by: Andre Przywara <andre.przywara@arm.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Nhat Pham <nphamcs@gmail.com> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Andre Przywara [Mon, 21 Aug 2023 16:05:33 +0000 (17:05 +0100)]
selftests: cachestat: test for cachestat availability
Patch series "selftests: cachestat: fix run on older kernels", v2.
I ran all kernel selftests on some test machine, and stumbled upon
cachestat failing (among others). These patches fix the run on older
kernels and when the current directory is on a tmpfs instance.
This patch (of 2):
As cachestat is a new syscall, it won't be available on older kernels, for
instance those running on a development machine. At the moment the test
reports all tests as "not ok" in this case.
Test for the cachestat syscall availability first, before doing further
tests, and bail out early with a TAP SKIP comment.
This also uses the opportunity to add the proper TAP headers, and add one
check for proper error handling (illegal file descriptor).
Liam R. Howlett [Sat, 19 Aug 2023 00:43:55 +0000 (20:43 -0400)]
maple_tree: disable mas_wr_append() when other readers are possible
The current implementation of append may cause duplicate data and/or
incorrect ranges to be returned to a reader during an update. Although
this has not been reported or seen, disable the append write operation
while the tree is in rcu mode out of an abundance of caution.
During the analysis of the mas_next_slot() the following was
artificially created by separating the writer and reader code:
Writer: reader:
mas_wr_append
set end pivot
updates end metata
Detects write to last slot
last slot write is to start of slot
store current contents in slot
overwrite old end pivot
mas_next_slot():
read end metadata
read old end pivot
return with incorrect range
store new value
Alternatively:
Writer: reader:
mas_wr_append
set end pivot
updates end metata
Detects write to last slot
last lost write to end of slot
store value
mas_next_slot():
read end metadata
read old end pivot
read new end pivot
return with incorrect range
set old end pivot
There may be other accesses that are not safe since we are now updating
both metadata and pointers, so disabling append if there could be rcu
readers is the safest action.
Yin Fengwei [Tue, 8 Aug 2023 02:09:17 +0000 (10:09 +0800)]
madvise:madvise_free_pte_range(): don't use mapcount() against large folio for sharing check
Commit 98b211d6415f ("madvise: convert madvise_free_pte_range() to use a
folio") replaced the page_mapcount() with folio_mapcount() to check
whether the folio is shared by other mapping.
It's not correct for large folios. folio_mapcount() returns the total
mapcount of large folio which is not suitable to detect whether the folio
is shared.
Use folio_estimated_sharers() which returns a estimated number of shares.
That means it's not 100% correct. It should be OK for madvise case here.
User-visible effects is that the THP is skipped when user call madvise.
But the correct behavior is THP should be split and processed then.
NOTE: this change is a temporary fix to reduce the user-visible effects
before the long term fix from David is ready.
Link: https://lkml.kernel.org/r/20230808020917.2230692-4-fengwei.yin@intel.com Fixes: 98b211d6415f ("madvise: convert madvise_free_pte_range() to use a folio") Signed-off-by: Yin Fengwei <fengwei.yin@intel.com> Reviewed-by: Yu Zhao <yuzhao@google.com> Reviewed-by: Ryan Roberts <ryan.roberts@arm.com> Cc: David Hildenbrand <david@redhat.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Yin Fengwei [Tue, 8 Aug 2023 02:09:16 +0000 (10:09 +0800)]
madvise:madvise_free_huge_pmd(): don't use mapcount() against large folio for sharing check
Commit fc986a38b670 ("mm: huge_memory: convert madvise_free_huge_pmd to
use a folio") replaced the page_mapcount() with folio_mapcount() to check
whether the folio is shared by other mapping.
It's not correct for large folios. folio_mapcount() returns the total
mapcount of large folio which is not suitable to detect whether the folio
is shared.
Use folio_estimated_sharers() which returns a estimated number of shares.
That means it's not 100% correct. It should be OK for madvise case here.
User-visible effects is that the THP is skipped when user call madvise.
But the correct behavior is THP should be split and processed then.
NOTE: this change is a temporary fix to reduce the user-visible effects
before the long term fix from David is ready.
Link: https://lkml.kernel.org/r/20230808020917.2230692-3-fengwei.yin@intel.com Fixes: fc986a38b670 ("mm: huge_memory: convert madvise_free_huge_pmd to use a folio") Signed-off-by: Yin Fengwei <fengwei.yin@intel.com> Reviewed-by: Yu Zhao <yuzhao@google.com> Reviewed-by: Ryan Roberts <ryan.roberts@arm.com> Cc: David Hildenbrand <david@redhat.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com> Cc: Yang Shi <shy828301@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Yin Fengwei [Tue, 8 Aug 2023 02:09:15 +0000 (10:09 +0800)]
madvise:madvise_cold_or_pageout_pte_range(): don't use mapcount() against large folio for sharing check
Patch series "don't use mapcount() to check large folio sharing", v2.
In madvise_cold_or_pageout_pte_range() and madvise_free_pte_range(),
folio_mapcount() is used to check whether the folio is shared. But it's
not correct as folio_mapcount() returns total mapcount of large folio.
Use folio_estimated_sharers() here as the estimated number is enough.
This patchset will fix the cases:
User space application call madvise() with MADV_FREE, MADV_COLD and
MADV_PAGEOUT for specific address range. There are THP mapped to the
range. Without the patchset, the THP is skipped. With the patch, the
THP will be split and handled accordingly.
David reported the cow self test skip some cases because of MADV_PAGEOUT
skip THP:
https://lore.kernel.org/linux-mm/9e92e42d-488f-47db-ac9d-75b24cd0d037@intel.com/T/#mbf0f2ec7fbe45da47526de1d7036183981691e81
and I confirmed this patchset make it work again.
This patch (of 3):
Commit 07e8c82b5eff ("madvise: convert madvise_cold_or_pageout_pte_range()
to use folios") replaced the page_mapcount() with folio_mapcount() to
check whether the folio is shared by other mapping.
It's not correct for large folio. folio_mapcount() returns the total
mapcount of large folio which is not suitable to detect whether the folio
is shared.
Use folio_estimated_sharers() which returns a estimated number of shares.
That means it's not 100% correct. It should be OK for madvise case here.
User-visible effects is that the THP is skipped when user call madvise.
But the correct behavior is THP should be split and processed then.
NOTE: this change is a temporary fix to reduce the user-visible effects
before the long term fix from David is ready.
Link: https://lkml.kernel.org/r/20230808020917.2230692-1-fengwei.yin@intel.com Link: https://lkml.kernel.org/r/20230808020917.2230692-2-fengwei.yin@intel.com Fixes: 07e8c82b5eff ("madvise: convert madvise_cold_or_pageout_pte_range() to use folios") Signed-off-by: Yin Fengwei <fengwei.yin@intel.com> Reviewed-by: Yu Zhao <yuzhao@google.com> Reviewed-by: Ryan Roberts <ryan.roberts@arm.com> Cc: David Hildenbrand <david@redhat.com> Cc: Kefeng Wang <wangkefeng.wang@huawei.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Linus Torvalds [Thu, 24 Aug 2023 21:30:47 +0000 (14:30 -0700)]
Merge tag 'nfsd-6.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
"Two last-minute one-liners for v6.5-rc. One got lost in the shuffle,
and the other was reported just this morning"
- Close race window when handling FREE_STATEID operations
- Fix regression in /proc/fs/nfsd/v4_end_grace introduced in v6.5-rc"
* tag 'nfsd-6.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
NFSD: Fix a thinko introduced by recent trace point changes
nfsd: Fix race to FREE_STATEID and cl_revoked
Linus Torvalds [Thu, 24 Aug 2023 20:55:35 +0000 (13:55 -0700)]
Merge tag 'spi-fix-v6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple more small driver specific fixes for v6.5.
The device mode for Cadence had been broken by some recent updates
done for host mode and large transfers for multi-byte words on stm32
had been broken by an API update in what I think was a rebasing
incident"
* tag 'spi-fix-v6.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-cadence: Fix data corruption issues in slave mode
spi: stm32: fix accidential revert to byte-sized transfer splitting
Mingzheng Xing [Thu, 24 Aug 2023 19:08:52 +0000 (03:08 +0800)]
riscv: Fix build errors using binutils2.37 toolchains
When building the kernel with binutils 2.37 and GCC-11.1.0/GCC-11.2.0,
the following error occurs:
Assembler messages:
Error: cannot find default versions of the ISA extension `zicsr'
Error: cannot find default versions of the ISA extension `zifencei'
The above error originated from this commit of binutils[0], which has been
resolved and backported by GCC-12.1.0[1] and GCC-11.3.0[2].
So fix this by change the GCC version in
CONFIG_TOOLCHAIN_NEEDS_OLD_ISA_SPEC to GCC-11.3.0.
Dave Airlie [Thu, 24 Aug 2023 19:15:54 +0000 (05:15 +1000)]
Merge tag 'drm-misc-fixes-2023-08-24' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
A samsung-dsim initialization fix, a devfreq fix for panfrost, a DP DSC
define fix, a recursive lock fix for dma-buf, a shader validation fix
and a reference counting fix for vmwgfx
- wifi: mac80211: limit reorder_buf_filtered to avoid UBSAN warning
- batman:
- do not get eth header before batadv_check_management_packet
- fix batadv_v_ogm_aggr_send memory leak
- bonding: fix macvlan over alb bond support
- mlxsw: set time stamp fields also when its type is MIRROR_UTC"
* tag 'net-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
selftests: bonding: add macvlan over bond testing
selftest: bond: add new topo bond_topo_2d1c.sh
bonding: fix macvlan over alb bond support
rtnetlink: Reject negative ifindexes in RTM_NEWLINK
netfilter: nf_tables: defer gc run if previous batch is still pending
netfilter: nf_tables: fix out of memory error handling
netfilter: nf_tables: use correct lock to protect gc_list
netfilter: nf_tables: GC transaction race with abort path
netfilter: nf_tables: flush pending destroy work before netlink notifier
netfilter: nf_tables: validate all pending tables
ibmveth: Use dcbf rather than dcbfl
i40e: fix potential NULL pointer dereferencing of pf->vf i40e_sync_vsi_filters()
net/sched: fix a qdisc modification with ambiguous command request
igc: Fix the typo in the PTM Control macro
batman-adv: Hold rtnl lock during MTU update via netlink
igb: Avoid starting unnecessary workqueues
can: raw: add missing refcount for memory leak fix
can: isotp: fix support for transmission of SF without flow control
bnx2x: new flag for track HW resource allocation
sfc: allocate a big enough SKB for loopback selftest packet
...
ASoC: amd: yc: Fix a non-functional mic on Lenovo 82SJ
Lenovo 82SJ doesn't have DMIC connected like 82V2 does. Narrow
the match down to only cover 82V2.
Reported-by: prosenfeld@Yuhsbstudents.org Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217063 Fixes: 2232b2dd8cd4 ("ASoC: amd: yc: Add Lenovo Yoga Slim 7 Pro X to quirks table") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com Link: https://lore.kernel.org/r/20230824011149.1395-1-mario.limonciello@amd.com Signed-off-by: Mark Brown <broonie@kernel.org
Feng Tang [Wed, 23 Aug 2023 06:57:47 +0000 (14:57 +0800)]
x86/fpu: Set X86_FEATURE_OSXSAVE feature after enabling OSXSAVE in CR4
0-Day found a 34.6% regression in stress-ng's 'af-alg' test case, and
bisected it to commit b81fac906a8f ("x86/fpu: Move FPU initialization into
arch_cpu_finalize_init()"), which optimizes the FPU init order, and moves
the CR4_OSXSAVE enabling into a later place:
As the FPU is not yet initialized the CPU capability setup fails to set
X86_FEATURE_OSXSAVE. Many security module like 'camellia_aesni_avx_x86_64'
depend on this feature and therefore fail to load, causing the regression.
Cure this by setting X86_FEATURE_OSXSAVE feature right after OSXSAVE
enabling.
[ tglx: Moved it into the actual BSP FPU initialization code and added a comment ]
Rick Edgecombe [Fri, 18 Aug 2023 17:03:05 +0000 (10:03 -0700)]
x86/fpu: Invalidate FPU state correctly on exec()
The thread flag TIF_NEED_FPU_LOAD indicates that the FPU saved state is
valid and should be reloaded when returning to userspace. However, the
kernel will skip doing this if the FPU registers are already valid as
determined by fpregs_state_valid(). The logic embedded there considers
the state valid if two cases are both true:
1: fpu_fpregs_owner_ctx points to the current tasks FPU state
2: the last CPU the registers were live in was the current CPU.
This is usually correct logic. A CPU’s fpu_fpregs_owner_ctx is set to
the current FPU during the fpregs_restore_userregs() operation, so it
indicates that the registers have been restored on this CPU. But this
alone doesn’t preclude that the task hasn’t been rescheduled to a
different CPU, where the registers were modified, and then back to the
current CPU. To verify that this was not the case the logic relies on the
second condition. So the assumption is that if the registers have been
restored, AND they haven’t had the chance to be modified (by being
loaded on another CPU), then they MUST be valid on the current CPU.
Besides the lazy FPU optimizations, the other cases where the FPU
registers might not be valid are when the kernel modifies the FPU register
state or the FPU saved buffer. In this case the operation modifying the
FPU state needs to let the kernel know the correspondence has been
broken. The comment in “arch/x86/kernel/fpu/context.h” has:
/*
...
* If the FPU register state is valid, the kernel can skip restoring the
* FPU state from memory.
*
* Any code that clobbers the FPU registers or updates the in-memory
* FPU state for a task MUST let the rest of the kernel know that the
* FPU registers are no longer valid for this task.
*
* Either one of these invalidation functions is enough. Invalidate
* a resource you control: CPU if using the CPU for something else
* (with preemption disabled), FPU for the current task, or a task that
* is prevented from running by the current task.
*/
However, this is not completely true. When the kernel modifies the
registers or saved FPU state, it can only rely on
__fpu_invalidate_fpregs_state(), which wipes the FPU’s last_cpu
tracking. The exec path instead relies on fpregs_deactivate(), which sets
the CPU’s FPU context to NULL. This was observed to fail to restore the
reset FPU state to the registers when returning to userspace in the
following scenario:
1. A task is executing in userspace on CPU0
- CPU0’s FPU context points to tasks
- fpu->last_cpu=CPU0
2. The task exec()’s
3. While in the kernel the task is preempted
- CPU0 gets a thread executing in the kernel (such that no other
FPU context is activated)
- Scheduler sets task’s fpu->last_cpu=CPU0 when scheduling out
4. Task is migrated to CPU1
5. Continuing the exec(), the task gets to
fpu_flush_thread()->fpu_reset_fpregs()
- Sets CPU1’s fpu context to NULL
- Copies the init state to the task’s FPU buffer
- Sets TIF_NEED_FPU_LOAD on the task
6. The task reschedules back to CPU0 before completing the exec() and
returning to userspace
- During the reschedule, scheduler finds TIF_NEED_FPU_LOAD is set
- Skips saving the registers and updating task’s fpu→last_cpu,
because TIF_NEED_FPU_LOAD is the canonical source.
7. Now CPU0’s FPU context is still pointing to the task’s, and
fpu->last_cpu is still CPU0. So fpregs_state_valid() returns true even
though the reset FPU state has not been restored.
So the root cause is that exec() is doing the wrong kind of invalidate. It
should reset fpu->last_cpu via __fpu_invalidate_fpregs_state(). Further,
fpu__drop() doesn't really seem appropriate as the task (and FPU) are not
going away, they are just getting reset as part of an exec. So switch to
__fpu_invalidate_fpregs_state().
Also, delete the misleading comment that says that either kind of
invalidate will be enough, because it’s not always the case.
Fixes: 33344368cb08 ("x86/fpu: Clean up the fpu__clear() variants") Reported-by: Lei Wang <lei4.wang@intel.com> Signed-off-by: Rick Edgecombe <rick.p.edgecombe@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Lijun Pan <lijun.pan@intel.com> Reviewed-by: Sohil Mehta <sohil.mehta@intel.com> Acked-by: Lijun Pan <lijun.pan@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230818170305.502891-1-rick.p.edgecombe@intel.com
Paolo Abeni [Thu, 24 Aug 2023 08:33:22 +0000 (10:33 +0200)]
Merge tag 'nf-23-08-23' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/netfilter/nf
Florian Westphal says:
====================
netfilter updates for net
This PR contains nf_tables updates for your *net* tree.
First patch fixes table validation, I broke this in 6.4 when tracking
validation state per table, reported by Pablo, fixup from myself.
Second patch makes sure objects waiting for memory release have been
released, this was broken in 6.1, patch from Pablo Neira Ayuso.
Patch three is a fix-for-fix from previous PR: In case a transaction
gets aborted, gc sequence counter needs to be incremented so pending
gc requests are invalidated, from Pablo.
Same for patch 4: gc list needs to use gc list lock, not destroy lock,
also from Pablo.
Patch 5 fixes a UaF in a set backend, but this should only occur when
failslab is enabled for GFP_KERNEL allocations, broken since feature
was added in 5.6, from myself.
Patch 6 fixes a double-free bug that was also added via previous PR:
We must not schedule gc work if the previous batch is still queued.
netfilter pull request 2023-08-23
* tag 'nf-23-08-23' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: defer gc run if previous batch is still pending
netfilter: nf_tables: fix out of memory error handling
netfilter: nf_tables: use correct lock to protect gc_list
netfilter: nf_tables: GC transaction race with abort path
netfilter: nf_tables: flush pending destroy work before netlink notifier
netfilter: nf_tables: validate all pending tables
====================
Paolo Abeni [Thu, 24 Aug 2023 08:07:16 +0000 (10:07 +0200)]
Merge branch 'fix-macvlan-over-alb-bond-support'
Hangbin Liu says:
====================
fix macvlan over alb bond support
Currently, the macvlan over alb bond is broken after commit 14af9963ba1e ("bonding: Support macvlans on top of tlb/rlb mode bonds").
Fix this and add relate tests.
====================
Hangbin Liu [Wed, 23 Aug 2023 07:19:04 +0000 (15:19 +0800)]
bonding: fix macvlan over alb bond support
The commit 14af9963ba1e ("bonding: Support macvlans on top of tlb/rlb mode
bonds") aims to enable the use of macvlans on top of rlb bond mode. However,
the current rlb bond mode only handles ARP packets to update remote neighbor
entries. This causes an issue when a macvlan is on top of the bond, and
remote devices send packets to the macvlan using the bond's MAC address
as the destination. After delivering the packets to the macvlan, the macvlan
will rejects them as the MAC address is incorrect. Consequently, this commit
makes macvlan over bond non-functional.
To address this problem, one potential solution is to check for the presence
of a macvlan port on the bond device using netif_is_macvlan_port(bond->dev)
and return NULL in the rlb_arp_xmit() function. However, this approach
doesn't fully resolve the situation when a VLAN exists between the bond and
macvlan.
So let's just do a partial revert for commit 14af9963ba1e in rlb_arp_xmit().
As the comment said, Don't modify or load balance ARPs that do not originate
locally.
Fixes: 14af9963ba1e ("bonding: Support macvlans on top of tlb/rlb mode bonds") Reported-by: susan.zheng@veritas.com Closes: https://bugzilla.redhat.com/show_bug.cgi?id=2117816 Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Ido Schimmel [Wed, 23 Aug 2023 06:43:48 +0000 (09:43 +0300)]
rtnetlink: Reject negative ifindexes in RTM_NEWLINK
Negative ifindexes are illegal, but the kernel does not validate the
ifindex in the ancillary header of RTM_NEWLINK messages, resulting in
the kernel generating a warning [1] when such an ifindex is specified.
Takashi Iwai [Thu, 24 Aug 2023 07:20:36 +0000 (09:20 +0200)]
Merge tag 'asoc-fix-v6.5-rc7' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v6.5
A relatively large but generally not super urgent set of fixes for ASoC,
including some quirks and a MAINTAINERS update. There's also an update
to cs35l56 to change the firmware ABI, there are no current shipping
systems which use the current interface and the sooner we get the new
interface in the less likely it is that something will start.
It'd be nice if these landed for v6.5 but not the end of the world if
they wait till v6.6.
Linus Torvalds [Wed, 23 Aug 2023 21:28:19 +0000 (14:28 -0700)]
Merge tag 'acpi-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Make an existing ACPI IRQ override quirk for PCSpecialist Elimina Pro
16 M work as intended (Hans de Goede)"
* tag 'acpi-6.5-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: resource: Fix IRQ override quirk for PCSpecialist Elimina Pro 16 M
Imre Deak [Tue, 22 Aug 2023 11:30:15 +0000 (14:30 +0300)]
drm/i915: Fix HPD polling, reenabling the output poll work as needed
After the commit in the Fixes: line below, HPD polling stopped working
on i915, since after that change calling drm_kms_helper_poll_enable()
doesn't restart drm_mode_config::output_poll_work if the work was
stopped (no connectors needing polling) and enabling polling for a
connector (during runtime suspend or detecting an HPD IRQ storm).
After the above change calling drm_kms_helper_poll_enable() is a nop
after it's been called already and polling for some connectors was
disabled/re-enabled.
Fix this by calling drm_kms_helper_poll_reschedule() added in the
previous patch instead, which reschedules the work whenever expected.
Fixes: d33a54e3991d ("drm/probe_helper: sort out poll_running vs poll_enabled") CC: stable@vger.kernel.org # 6.4+ Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Cc: dri-devel@lists.freedesktop.org Reviewed-by: Jouni Högander <jouni.hogander@intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-2-imre.deak@intel.com
(cherry picked from commit 50452f2f76852322620b63e62922b85e955abe94) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
projects / linux-stable / log