ASMedia have confirmed that all ASM106x parts currently listed in
ahci_pci_tbl[] suffer from the 43-bit DMA address limitation that we ran
into on the ASM1061, and therefore, we need to apply the quirk added by
commit 20730e9b2778 ("ahci: add 43-bit DMA address quirk for ASMedia
ASM1061 controllers") to the other supported ASM106x parts as well.
This patch adds the ability to send RM_ADDR for local ID 0. Check
whether id 0 address is removed, if not, put id 0 into a removing
list, pass it to mptcp_pm_remove_addr() to remove id 0 address.
There is no reason not to allow the userspace to remove the initial
address (ID 0). This special case was not taken into account not
letting the userspace to delete all addresses as announced.
To avoid duplicated code in different MPTCP selftests, we can add
and use helpers defined in mptcp_lib.sh.
The helper get_counter() in mptcp_join.sh and get_mib_counter() in
mptcp_connect.sh have the same functionality, export get_counter() into
mptcp_lib.sh and rename it as mptcp_lib_get_counter(). Use this new
helper instead of get_counter() and get_mib_counter().
Use this helper in test_prio() in userspace_pm.sh too instead of
open-coding.
Since the "Fixes" commits mentioned below, the newly added "userspace
pm" subtests of mptcp_join selftests are launching the whole transfer in
the background, do the required checks, then wait for the end of
transfer.
There is no need to wait longer, especially because the checks at the
end of the transfer are ignored (which is fine). This saves quite a few
seconds on slow environments.
While at it, use 'mptcp_lib_kill_wait()' helper everywhere, instead of
on a specific one with 'kill_tests_wait()'.
In zswap_writeback_entry(), after we get a folio from
__read_swap_cache_async(), we grab the tree lock again to check that the
swap entry was not invalidated and recycled. If it was, we delete the
folio we just added to the swap cache and exit.
However, __read_swap_cache_async() returns the folio locked when it is
newly allocated, which is always true for this path, and the folio is
ref'd. Make sure to unlock and put the folio before returning.
This was discovered by code inspection, probably because this path handles
a race condition that should not happen often, and the bug would not crash
the system, it will only strand the folio indefinitely.
We have to invalidate any duplicate entry even when !zswap_enabled since
zswap can be disabled anytime. If the folio store success before, then
got dirtied again but zswap disabled, we won't invalidate the old
duplicate entry in the zswap_store(). So later lru writeback may
overwrite the new data in swapfile.
Since the "Fixes" commit mentioned below, "userspace pm" subtests of
mptcp_join selftests introduced in v6.5 are launching the whole transfer
in the background, do the required checks, then wait for the end of
transfer.
There is no need to wait longer, especially because the checks at the
end of the transfer are ignored (which is fine). This saves quite a few
seconds in slow environments.
Note that old versions will need commit bdbef0a6ff10 ("selftests: mptcp:
add mptcp_lib_kill_wait") as well to get 'mptcp_lib_kill_wait()' helper.
When being a target, NAK from the controller means that all bytes have
been transferred. So, the last byte needs also to be marked as
'processed'. Otherwise index registers of backends may not increase.
Fixes: f7414cd6923f ("i2c: imx: support slave mode for imx I2C driver") Signed-off-by: Corey Minyard <minyard@acm.org> Tested-by: Andrew Manley <andrew.manley@sealingtech.com> Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
[wsa: fixed comment and commit message to properly describe the case] Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 743b9786b14a ("drm/amd/display: Hook up the DMUB service in DM") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The config fragment doesn't follow the correct format to enable those
config options which make the config options getting missed while
merging with other configs.
➜ merge_config.sh -m .config tools/testing/selftests/iommu/config
Using .config as base
Merging tools/testing/selftests/iommu/config
➜ make olddefconfig
.config:5295:warning: unexpected data: CONFIG_IOMMUFD
.config:5296:warning: unexpected data: CONFIG_IOMMUFD_TEST
While at it, add CONFIG_FAULT_INJECTION as well which is needed for
CONFIG_IOMMUFD_TEST. If CONFIG_FAULT_INJECTION isn't present in base
config (such as x86 defconfig), CONFIG_IOMMUFD_TEST doesn't get enabled.
During syncobj_eventfd_entry_func, dma_fence_chain_find_seqno may set
the fence to NULL if the given seqno is signaled and a later seqno has
already been submitted. In that case, the eventfd should be signaled
immediately which currently does not happen.
This is a similar issue to the one addressed by commit b19926d4f3a6
("drm/syncobj: Deal with signalled fences in drm_syncobj_find_fence.").
As a fix, if the return value of dma_fence_chain_find_seqno indicates
success but it sets the fence to NULL, we will assign a stub fence to
ensure the following code still signals the eventfd.
v1 -> v2: assign a stub fence instead of signaling the eventfd
When waiting for a syncobj timeline point whose fence has not yet been
submitted with the WAIT_FOR_SUBMIT flag, a callback is registered using
drm_syncobj_fence_add_wait and the thread is put to sleep until the
timeout expires. If the fence is submitted before then,
drm_syncobj_add_point will wake up the sleeping thread immediately which
will proceed to wait for the fence to be signaled.
However, if the WAIT_AVAILABLE flag is used instead,
drm_syncobj_fence_add_wait won't get called, meaning the waiting thread
will always sleep for the full timeout duration, even if the fence gets
submitted earlier. If it turns out that the fence *has* been submitted
by the time it eventually wakes up, it will still indicate to userspace
that the wait completed successfully (it won't return -ETIME), but it
will have taken much longer than it should have.
To fix this, we must call drm_syncobj_fence_add_wait if *either* the
WAIT_FOR_SUBMIT flag or the WAIT_AVAILABLE flag is set. The only
difference being that with WAIT_FOR_SUBMIT we will also wait for the
fence to be signaled after it has been submitted while with
WAIT_AVAILABLE we will return immediately.
IGT test patch: https://lists.freedesktop.org/archives/igt-dev/2024-January/067537.html
Fixes: 01d6c3578379 ("drm/syncobj: add support for timeline point wait v8") Signed-off-by: Erik Kurzinger <ekurzinger@nvidia.com> Signed-off-by: Simon Ser <contact@emersion.fr> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Simon Ser <contact@emersion.fr> Link: https://patchwork.freedesktop.org/patch/msgid/20240119163208.3723457-1-ekurzinger@nvidia.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit bb726b753f75 ("net: phy: realtek: add support for
RTL8211F(D)(I)-VD-CG") extended support of the driver from the existing
support for RTL8211F(D)(I)-CG PHY to the newer RTL8211F(D)(I)-VD-CG PHY.
While that commit indicated that the RTL8211F_PHYCR2 register is not
supported by the "VD-CG" PHY model and therefore updated the corresponding
section in rtl8211f_config_init() to be invoked conditionally, the call to
"genphy_soft_reset()" was left as-is, when it should have also been invoked
conditionally. This is because the call to "genphy_soft_reset()" was first
introduced by the commit 0a4355c2b7f8 ("net: phy: realtek: add dt property
to disable CLKOUT clock") since the RTL8211F guide indicates that a PHY
reset should be issued after setting bits in the PHYCR2 register.
As the PHYCR2 register is not applicable to the "VD-CG" PHY model, fix the
rtl8211f_config_init() function by invoking "genphy_soft_reset()"
conditionally based on the presence of the "PHYCR2" register.
Fixes: bb726b753f75 ("net: phy: realtek: add support for RTL8211F(D)(I)-VD-CG") Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240220070007.968762-1-s-vadapalli@ti.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ioam6_fill_trace_data() writes inside the skb payload without ensuring
it's writeable (e.g., not cloned). This function is called both from the
input and output path. The output path (ioam6_iptunnel) already does the
check. This commit provides a fix for the input path, inside
ipv6_hop_ioam(). It also updates ip6_parse_tlv() to refresh the network
header pointer ("nh") when returning from ipv6_hop_ioam().
Fixes: 9ee11f0fff20 ("ipv6: ioam: Data plane support for Pre-allocated Trace") Reported-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Justin Iurman <justin.iurman@uliege.be> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The receive queues are protected by their respective spin-lock, not
the socket lock. This could lead to skb_peek() unexpectedly
returning NULL or a pointer to an already dequeued socket buffer.
Fixes: 9641458d3ec4 ("Phonet: Pipe End Point for Phonet Pipes protocol") Signed-off-by: Rémi Denis-Courmont <courmisch@gmail.com> Link: https://lore.kernel.org/r/20240218081214.4806-2-remi@remlab.net Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both registers used when doing manual injection or fdma injection are
shared between all the net devices of the switch. It was noticed that
when having two process which each of them trying to inject frames on
different ethernet ports, that the HW started to behave strange, by
sending out more frames then expected. When doing fdma injection it is
required to set the frame in the DCB and then make sure that the next
pointer of the last DCB is invalid. But because there is no locks for
this, then easily this pointer between the DCB can be broken and then it
would create a loop of DCBs. And that means that the HW will
continuously transmit these frames in a loop. Until the SW will break
this loop.
Therefore to fix this issue, add a spin lock for when accessing the
registers for manual or fdma injection.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Machon <daniel.machon@microchip.com> Fixes: f3cad2611a77 ("net: sparx5: add hostmode with phylink support") Link: https://lore.kernel.org/r/20240219080043.1561014-1-horatiu.vultur@microchip.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike other commands, due to a c&p error, port dump fills-up cmd with
wrong value, different from port-get request cmd, port-get doit reply
and port notification.
Fix it by filling cmd with value DEVLINK_CMD_PORT_NEW.
Skimmed through devlink userspace implementations, none of them cares
about this cmd value. Only ynl, for which, this is actually a fix, as it
expects doit and dumpit ops rsp_value to be the same.
Omit the fixes tag, even thought this is fix, better to target this for
next release.
Fixes: bfcd3a466172 ("Introduce devlink infrastructure") Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/r/20240220075245.75416-1-jiri@resnulli.us Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure to free the already-parsed mcast_groups if
we don't get an ack from the kernel when reading family info.
This is part of the ynl_sock_create() error path, so we won't
get a call to ynl_sock_destroy() to free them later.
Fixes: 86878f14d71a ("tools: ynl: user space helpers") Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Link: https://lore.kernel.org/r/20240220161112.2735195-3-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is one common error handler in ynl - ynl_cb_error().
It expects priv to be a pointer to struct ynl_parse_arg AKA yarg.
To avoid potential crashes if we encounter a stray NLMSG_ERROR
always pass yarg as priv (or a struct which has it as the first
member).
ynl_cb_null() has a similar problem directly - it expects yarg
but priv passed by the caller is ys.
Found by code inspection.
Fixes: 86878f14d71a ("tools: ynl: user space helpers") Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Link: https://lore.kernel.org/r/20240220161112.2735195-2-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We may hold an extra reference on a socket if a tag allocation fails: we
optimistically allocate the sk_key, and take a ref there, but do not
drop if we end up not using the allocated key.
Ensure we're dropping the sock on this failure by doing a proper unref
rather than directly kfree()ing.
Register hooks last when adding chain/flowtable to ensure that packets do
not walk over datastructure that is being released in the error path
without waiting for the rcu grace period.
Fixes: 91c7b38dc9f0 ("netfilter: nf_tables: use new transaction infrastructure to handle chain") Fixes: 3b49e2e94e6e ("netfilter: nf_tables: add flow table netlink frontend") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dst is transferred to the flow object, route object does not own it
anymore. Reset dst in route object, otherwise if flow_offload_add()
fails, error path releases dst twice, leading to a refcount underflow.
If we queue 3 records:
- record 1, type DATA
- record 2, some other type
- record 3, type DATA
and do a recv(PEEK), the rx_list will contain the first two records.
The next large recv will walk through the rx_list and copy data from
record 1, then stop because record 2 is a different type. Since we
haven't filled up our buffer, we will process the next available
record. It's also DATA, so we can merge it with the current read.
We shouldn't do that, since there was a record in between that we
ignored.
Add a flag to let process_rx_list inform tls_sw_recvmsg that it had
more data available.
If we have a non-DATA record on the rx_list and another record of the
same type still on the queue, we will end up merging them:
- process_rx_list copies the non-DATA record
- we start the loop and process the first available record since it's
of the same type
- we break out of the loop since the record was not DATA
Just check the record type and jump to the end in case process_rx_list
did some work.
PEEK needs to leave decrypted records on the rx_list so that we can
receive them later on, so it jumps back into the async code that
queues the skb. Unfortunately that makes us skip the
TLS_RECORD_TYPE_DATA check at the bottom of the main loop, so if two
records of the same (non-DATA) type are queued, we end up merging
them.
Add the same record type check, and make it unlikely to not penalize
the async fastpath. Async decrypt only applies to data record, so this
check is only needed for PEEK.
The number of temperature configuration registers does
not always match the total number of temperature registers.
This can result in access errors reported if KASAN is enabled.
BUG: KASAN: global-out-of-bounds in nct6775_probe+0x5654/0x6fe9 nct6775_core
If sk_psock_verdict_data_ready() and sk_psock_stop_verdict() are called
concurrently, psock->saved_data_ready can be NULL, causing the above issue.
This patch fixes this issue by calling the appropriate data ready function
using the sk_psock_data_ready() helper and protecting it from concurrency
with sk->sk_callback_lock.
Fixes: 6df7f764cd3c ("bpf, sockmap: Wake up polling after data copy") Reported-by: syzbot+fd7b34375c1c8ce29c93@syzkaller.appspotmail.com Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: syzbot+fd7b34375c1c8ce29c93@syzkaller.appspotmail.com Acked-by: John Fastabend <john.fastabend@gmail.com> Closes: https://syzkaller.appspot.com/bug?extid=fd7b34375c1c8ce29c93 [1] Link: https://lore.kernel.org/bpf/20240218150933.6004-1-syoshida@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The signature for __iowrite64_copy() requires the number of 64 bit
quantities, not bytes. Multiple by 8 to get to a byte length before
invoking zpci_memcpy_toio()
Fixes: 87bc359b9822 ("s390/pci: speed up __iowrite64_copy by using pci store block insn") Acked-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Link: https://lore.kernel.org/r/0-v1-9223d11a7662+1d7785-s390_iowrite64_jgg@nvidia.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In newer hardware, IPA supports more than 32 endpoints. Some
registers--such as IPA interrupt registers--represent endpoints
as bits in a 4-byte register, and such registers are repeated as
needed to represent endpoints beyond the first 32.
In ipa_interrupt_suspend_clear_all(), we clear all pending IPA
suspend interrupts by reading all status register(s) and writing
corresponding registers to clear interrupt conditions.
Unfortunately the number of registers to read/write is calculated
incorrectly, and as a result we access *many* more registers than
intended. This bug occurs only when the IPA hardware signals a
SUSPEND interrupt, which happens when a packet is received for an
endpoint (or its underlying GSI channel) that is suspended. This
situation is difficult to reproduce, but possible.
Fix this by correctly computing the number of interrupt registers to
read and write. This is the only place in the code where registers
that map endpoints or channels this way perform this calculation.
Fixes: f298ba785e2d ("net: ipa: add a parameter to suspend registers") Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
AF reserves MCAM entries for each PF, VF present in the
system and populates the entry with DMAC and action with
default RSS so that basic packet I/O works. Since PF/VF is
not aware of the RSS action installed by AF, AF only fixup
the actions of the rules installed by PF/VF with corresponding
default RSS action. This worked well for rules installed by
PF/VF for features like RX VLAN offload and DMAC filters but
rules involving action like drop/forward to queue are also
getting modified by AF. Hence fix it by setting the default
RSS action only if requested by PF/VF.
Fixes: 967db3529eca ("octeontx2-af: add support for multicast/promisc packet replication feature") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 1fd4a5a36f9f ("drm/connector: Rename legacy TV property") failed
to update all the users of the struct drm_tv_connector_state mode field,
which resulted in a build failure in i915.
However, a subsequent commit in the same series reintroduced a mode
field in that structure, with a different semantic but the same type,
with the assumption that all previous users were updated.
Since that didn't happen, the i915 driver now compiles, but mixes
accesses to the legacy_mode field and the newer mode field, but with the
previous semantics.
This obviously doesn't work very well, so we need to update the accesses
that weren't in the legacy renaming commit.
Fixes: 1fd4a5a36f9f ("drm/connector: Rename legacy TV property") Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Maxime Ripard <mripard@kernel.org> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240220131251.453060-1-mripard@kernel.org
(cherry picked from commit bf7626f19d6ff14b9722273e23700400cc4d78ba) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Randomly a Lenovo Z13 will trigger a kernel warning traceback from this
condition:
```
if (WARN_ON((profile < 0) || (profile >= ARRAY_SIZE(profile_names))))
```
This happens because thinkpad-acpi always assumes that
convert_dytc_to_profile() successfully updated the profile. On the
contrary a condition can occur that when dytc_profile_refresh() is called
the profile doesn't get updated as there is a -EOPNOTSUPP branch.
Catch this situation and avoid updating the profile. Also log this into
dynamic debugging in case any other modes should be added in the future.
Fixes: c3bfcd4c6762 ("platform/x86: thinkpad_acpi: Add platform profile support") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20240217022311.113879-1-mario.limonciello@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fields in SMCR_EL1 reset to an architecturally UNKNOWN value. Since we
do not otherwise manage the traps configured in this register at runtime we
need to reconfigure them after a suspend in case nothing else was kind
enough to preserve them for us. Do so for SMCR_EL1.EZT0.
Fixes: d4913eee152d ("arm64/sme: Add basic enumeration for SME2") Reported-by: Jackson Cooper-Driver <Jackson.Cooper-Driver@arm.com> Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20240213-arm64-sme-resume-v3-2-17e05e493471@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fields in SMCR_EL1 and SMPRI_EL1 reset to an architecturally UNKNOWN
value. Since we do not otherwise manage the traps configured in this
register at runtime we need to reconfigure them after a suspend in case
nothing else was kind enough to preserve them for us.
The vector length will be restored as part of restoring the SME state for
the next SME using task.
Fixes: a1f4ccd25cc2 ("arm64/sme: Provide Kconfig for SME") Reported-by: Jackson Cooper-Driver <Jackson.Cooper-Driver@arm.com> Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20240213-arm64-sme-resume-v3-1-17e05e493471@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzkaller reported an overflown write in arp_req_get(). [0]
When ioctl(SIOCGARP) is issued, arp_req_get() looks up an neighbour
entry and copies neigh->ha to struct arpreq.arp_ha.sa_data.
The arp_ha here is struct sockaddr, not struct sockaddr_storage, so
the sa_data buffer is just 14 bytes.
In the splat below, 2 bytes are overflown to the next int field,
arp_flags. We initialise the field just after the memcpy(), so it's
not a problem.
However, when dev->addr_len is greater than 22 (e.g. MAX_ADDR_LEN),
arp_netmask is overwritten, which could be set as htonl(0xFFFFFFFFUL)
in arp_ioctl() before calling arp_req_get().
To avoid the overflow, let's limit the max length of memcpy().
Note that commit b5f0de6df6dc ("net: dev: Convert sa_data to flexible
array in struct sockaddr") just silenced syzkaller.
The pernet operations structure for the subsystem must be registered
before registering the generic netlink family.
Fixes: 915d7e5e5930 ("ipv6: sr: add code base for control plane support of SR-IPv6") Signed-off-by: Vasiliy Kovalev <kovalev@altlinux.org> Link: https://lore.kernel.org/r/20240215202717.29815-1-kovalev@altlinux.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Debugging shows a large number of unaligned access traps in the unwinder
code. Code analysis reveals a number of issues with this code:
- handle_interruption is passed twice through
dereference_kernel_function_descriptor()
- ret_from_kernel_thread, syscall_exit, intr_return,
_switch_to_ret, and _call_on_stack are passed through
dereference_kernel_function_descriptor() even though they are
not declared as function pointers.
To fix the problems, drop one of the calls to
dereference_kernel_function_descriptor() for handle_interruption,
and compare the other pointers directly.
Fixes: 6414b30b39f9 ("parisc: unwind: Avoid missing prototype warning for handle_interruption()") Fixes: 8e0ba125c2bf ("parisc/unwind: fix unwinder when CONFIG_64BIT is enabled") Cc: Helge Deller <deller@gmx.de> Cc: Sven Schnelle <svens@stackframe.org> Cc: John David Anglin <dave.anglin@bell.net> Cc: Charlie Jenkins <charlie@rivosinc.com> Cc: David Laight <David.Laight@ACULAB.COM> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In bpf_timer_cancel_and_free, this patch frees the timer->timer
after a rcu grace period. This requires a rcu_head addition
to the "struct bpf_hrtimer". Another kfree(t) happens in bpf_timer_init,
this does not need a kfree_rcu because it is still under the
spin_lock and timer->timer has not been visible by others yet.
In bpf_timer_cancel, rcu_read_lock() is added because this helper
can be used in a non rcu critical section context (e.g. from
a sleepable bpf prog). Other timer->timer usages in helpers.c
have been audited, bpf_timer_cancel() is the only place where
timer->timer is used outside of the spin_lock.
Another solution considered is to mark a t->flag in bpf_timer_cancel
and clear it after hrtimer_cancel() is done. In bpf_timer_cancel_and_free,
it busy waits for the flag to be cleared before kfree(t). This patch
goes with a straight forward solution and frees timer->timer after
a rcu grace period.
Fixes: b00628b1c7d5 ("bpf: Introduce bpf timers.") Suggested-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Hou Tao <houtao1@huawei.com> Link: https://lore.kernel.org/bpf/20240215211218.990808-1-martin.lau@linux.dev Signed-off-by: Sasha Levin <sashal@kernel.org>
Platform clock and phy error resources are not cleaned up in Xilinx GT PHY
error path.
To fix introduce the function ceva_ahci_platform_enable_resources() which
is a customized version of ahci_platform_enable_resources() and inline with
SATA IP programming sequence it does:
- Assert SATA reset
- Program PS GTR phy
- Bring SATA by de-asserting the reset
- Wait for GT lane PLL to be locked
ceva_ahci_platform_enable_resources() is also used in the resume path
as the same SATA programming sequence (as in probe) should be followed.
Also cleanup the mixed usage of ahci_platform_enable_resources() and custom
implementation in the probe function as both are not required.
Fixes: 9a9d3abe24bb ("ata: ahci: ceva: Update the driver to support xilinx GT phy") Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In bond priority testing, we set the primary interface to eth1 and add
eth0,1,2 to bond in serial. This is OK in normal times. But when in
debug kernel, the bridge port that eth0,1,2 connected would start
slowly (enter blocking, forwarding state), which caused the primary
interface down for a while after enslaving and active slave changed.
Here is a test log from Jakub's debug test[1].
[ 400.399070][ T50] br0: port 1(s0) entered disabled state
[ 400.400168][ T50] br0: port 4(s2) entered disabled state
[ 400.941504][ T2791] bond0: (slave eth0): making interface the new active one
[ 400.942603][ T2791] bond0: (slave eth0): Enslaving as an active interface with an up link
[ 400.943633][ T2766] br0: port 1(s0) entered blocking state
[ 400.944119][ T2766] br0: port 1(s0) entered forwarding state
[ 401.128792][ T2792] bond0: (slave eth1): making interface the new active one
[ 401.130771][ T2792] bond0: (slave eth1): Enslaving as an active interface with an up link
[ 401.131643][ T69] br0: port 2(s1) entered blocking state
[ 401.132067][ T69] br0: port 2(s1) entered forwarding state
[ 401.346201][ T2793] bond0: (slave eth2): Enslaving as a backup interface with an up link
[ 401.348414][ T50] br0: port 4(s2) entered blocking state
[ 401.348857][ T50] br0: port 4(s2) entered forwarding state
[ 401.519669][ T250] bond0: (slave eth0): link status definitely down, disabling slave
[ 401.526522][ T250] bond0: (slave eth1): link status definitely down, disabling slave
[ 401.526986][ T250] bond0: (slave eth2): making interface the new active one
[ 401.629470][ T250] bond0: (slave eth0): link status definitely up
[ 401.630089][ T250] bond0: (slave eth1): link status definitely up
[...]
# TEST: prio (active-backup ns_ip6_target primary_reselect 1) [FAIL]
# Current active slave is eth2 but not eth1
Fix it by setting active slave to primary slave specifically before
testing.
Fixes: 481b56e0391e ("selftests: bonding: re-format bond option tests") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit a940904443e4 ("powerpc/iommu: Add iommu_ops to report capabilities
and allow blocking domains") broke DLPAR add of PCI devices.
The above added iommu_device structure to pci_controller. During
system boot, PCI devices are discovered and this newly added iommu_device
structure is initialized by a call to iommu_device_register().
During DLPAR add of a PCI device, a new pci_controller structure is
allocated but there are no calls made to iommu_device_register()
interface.
Fix is to register the iommu device during DLPAR add as well.
Fixes: a940904443e4 ("powerpc/iommu: Add iommu_ops to report capabilities and allow blocking domains") Signed-off-by: Gaurav Batra <gbatra@linux.ibm.com> Reviewed-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20240215221833.4817-1-gbatra@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Avoid the PHY library call unnecessarily into the suspend/resume
functions by setting phydev->mac_managed_pm to true. The ASP driver
essentially does exactly what mdio_bus_phy_resume() does.
Fixes: 490cb412007d ("net: bcmasp: Add support for ASP2.0 Ethernet controller") Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Justin Chen <justin.chen@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
net->dev_base_seq and ipv6.dev_addr_genid are monotonically increasing.
If we XOR their values, we could miss to detect if both values
were changed with the same amount.
Fixes: 63998ac24f83 ("ipv6: provide addr and netconf dump consistency info") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
net->dev_base_seq and ipv4.dev_addr_genid are monotonically increasing.
If we XOR their values, we could miss to detect if both values
were changed with the same amount.
Fixes: 0465277f6b3f ("ipv4: provide addr and netconf dump consistency info") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If 'dev' or 'data' is NULL, the 'priv' variable has an incorrect address
when dereferencing calling netdev_err().
Since we get as 'dev_id' or 'data' what was passed as the 'dev' argument
to request_irq() during interrupt initialization (that is, the net_device
and rx/tx queue pointers initialized at the time of the call) and since
there are usually no checks for the 'dev_id' argument in such handlers
in other drivers, remove these checks from the handlers in stmmac driver.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 8532f613bc78 ("net: stmmac: introduce MSI Interrupt routines for mac, safety, RX & TX") Signed-off-by: Pavel Sakharov <p.sakharov@ispras.ru> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The compare function used to sort memblks into starting address
order fails when the result of its u64 address subtraction gets
truncated to an int upon return.
The impact of the bad sort is that memblks will be filled out
incorrectly. Depending on the set of memblks, a user may see no
errors at all but still have a bad fill, or see messages reporting
a node overlap that leads to numa init failure:
[] node 0 [mem: ] overlaps with node 1 [mem: ]
[] No NUMA configuration found
Replace with a comparison that can only result in: 1, 0, -1.
Fixes: 8f012db27c95 ("x86/numa: Introduce numa_fill_memblks()") Signed-off-by: Alison Schofield <alison.schofield@intel.com> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Link: https://lore.kernel.org/r/99dcb3ae87e04995e9f293f6158dc8fa0749a487.1705085543.git.alison.schofield@intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
numa_fill_memblks() fills in the gaps in numa_meminfo memblks over a
physical address range. To do so, it first creates a list of existing
memblks that overlap that address range. The issue is that it is off
by one when comparing to the end of the address range, so memblks
that do not overlap are selected.
The impact of selecting a memblk that does not actually overlap is
that an existing memblk may be filled when the expected action is to
do nothing and return NUMA_NO_MEMBLK to the caller. The caller can
then add a new NUMA node and memblk.
Replace the broken open-coded search for address overlap with the
memblock helper memblock_addrs_overlap(). Update the kernel doc
and in code comments.
clang-16 warns about casting between incompatible function types:
drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadow.c:161:10: error: cast from 'void (*)(const struct firmware *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
161 | .fini = (void(*)(void *))release_firmware,
This one was done to use the generic shadow_fw_release() function as a
callback for struct nvbios_source. Change it to use the same prototype
as the other five instances, with a trivial helper function that actually
calls release_firmware.
If we're redirecting the skb, and haven't called tcf_mirred_forward(),
yet, we need to tell the core to drop the skb by setting the retcode
to SHOT. If we have called tcf_mirred_forward(), however, the skb
is out of our hands and returning SHOT will lead to UaF.
Move the retval override to the error path which actually need it.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Fixes: e5cf1baf92cb ("act_mirred: use TC_ACT_REINSERT when possible") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The test Davide added in commit ca22da2fbd69 ("act_mirred: use the backlog
for nested calls to mirred ingress") hangs our testing VMs every 10 or so
runs, with the familiar tcp_v4_rcv -> tcp_v4_rcv deadlock reported by
lockdep.
The problem as previously described by Davide (see Link) is that
if we reverse flow of traffic with the redirect (egress -> ingress)
we may reach the same socket which generated the packet. And we may
still be holding its socket lock. The common solution to such deadlocks
is to put the packet in the Rx backlog, rather than run the Rx path
inline. Do that for all egress -> ingress reversals, not just once
we started to nest mirred calls.
In the past there was a concern that the backlog indirection will
lead to loss of error reporting / less accurate stats. But the current
workaround does not seem to address the issue.
Fixes: 53592b364001 ("net/sched: act_mirred: Implement ingress actions") Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Suggested-by: Davide Caratti <dcaratti@redhat.com> Link: https://lore.kernel.org/netdev/33dc43f587ec1388ba456b4915c75f02a8aae226.1663945716.git.dcaratti@redhat.com/ Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As a preparation for adding block ID to mirred, separate the part of
mirred that redirect/mirrors to a dev into a specific function so that it
can be called by blockcast for each dev.
Also improve readability. Eg. rename use_reinsert to dont_clone and skb2
to skb_to_send.
Co-developed-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Co-developed-by: Pedro Tammela <pctammela@mojatatu.com> Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Signed-off-by: Victor Nogueira <victor@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 52f671db1882 ("net/sched: act_mirred: use the backlog for mirred ingress") Signed-off-by: Sasha Levin <sashal@kernel.org>
However, the syzkaller's log hinted that connect() failed just before
the warning due to FAULT_INJECTION. [1]
When connect() is called for an unbound socket, we search for an
available ephemeral port. If a bhash bucket exists for the port, we
call __inet_check_established() or __inet6_check_established() to check
if the bucket is reusable.
If reusable, we add the socket into ehash and set inet_sk(sk)->inet_num.
Later, we look up the corresponding bhash2 bucket and try to allocate
it if it does not exist.
Although it rarely occurs in real use, if the allocation fails, we must
revert the changes by check_established(). Otherwise, an unconnected
socket could illegally occupy an ehash entry.
Note that we do not put tw back into ehash because sk might have
already responded to a packet for tw and it would be better to free
tw earlier under such memory presure.
Reported-by: syzkaller <syzkaller@googlegroups.com> Fixes: 28044fc1d495 ("net: Add a bhash2 table hashed by port and address") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When unoffloading a device, it is important to ensure that all
relevant deferred events are delivered to it before it disassociates
itself from the bridge.
Before this change, this was true for the normal case when a device
maps 1:1 to a net_bridge_port, i.e.
br0
/
swp0
When swp0 leaves br0, the call to switchdev_deferred_process() in
del_nbp() makes sure to process any outstanding events while the
device is still associated with the bridge.
In the case when the association is indirect though, i.e. when the
device is attached to the bridge via an intermediate device, like a
LAG...
br0
/
lag0
/
swp0
...then detaching swp0 from lag0 does not cause any net_bridge_port to
be deleted, so there was no guarantee that all events had been
processed before the device disassociated itself from the bridge.
Fix this by always synchronously processing all deferred events before
signaling completion of unoffloading back to the driver.
Fixes: 4e51bf44a03a ("net: bridge: move the switchdev object replay helpers to "push" mode") Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Before this change, generation of the list of MDB events to replay
would race against the creation of new group memberships, either from
the IGMP/MLD snooping logic or from user configuration.
While new memberships are immediately visible to walkers of
br->mdb_list, the notification of their existence to switchdev event
subscribers is deferred until a later point in time. So if a replay
list was generated during a time that overlapped with such a window,
it would also contain a replay of the not-yet-delivered event.
The driver would thus receive two copies of what the bridge internally
considered to be one single event. On destruction of the bridge, only
a single membership deletion event was therefore sent. As a
consequence of this, drivers which reference count memberships (at
least DSA), would be left with orphan groups in their hardware
database when the bridge was destroyed.
This is only an issue when replaying additions. While deletion events
may still be pending on the deferred queue, they will already have
been removed from br->mdb_list, so no duplicates can be generated in
that scenario.
To a user this meant that old group memberships, from a bridge in
which a port was previously attached, could be reanimated (in
hardware) when the port joined a new bridge, without the new bridge's
knowledge.
For example, on an mv88e6xxx system, create a snooping bridge and
immediately add a port to it:
root@infix-06-0b-00:~$ ip link add dev br0 up type bridge mcast_snooping 1 && \
> ip link set dev x3 up master br0
And then destroy the bridge:
root@infix-06-0b-00:~$ ip link del dev br0
root@infix-06-0b-00:~$ mvls atu
ADDRESS FID STATE Q F 0 1 2 3 4 5 6 7 8 9 a
DEV:0 Marvell 88E6393X
33:33:00:00:00:6a 1 static - - 0 . . . . . . . . . .
33:33:ff:87:e4:3f 1 static - - 0 . . . . . . . . . .
ff:ff:ff:ff:ff:ff 1 static - - 0 1 2 3 4 5 6 7 8 9 a
root@infix-06-0b-00:~$
The two IPv6 groups remain in the hardware database because the
port (x3) is notified of the host's membership twice: once via the
original event and once via a replay. Since only a single delete
notification is sent, the count remains at 1 when the bridge is
destroyed.
Then add the same port (or another port belonging to the same hardware
domain) to a new bridge, this time with snooping disabled:
root@infix-06-0b-00:~$ ip link add dev br1 up type bridge mcast_snooping 0 && \
> ip link set dev x3 up master br1
All multicast, including the two IPv6 groups from br0, should now be
flooded, according to the policy of br1. But instead the old
memberships are still active in the hardware database, causing the
switch to only forward traffic to those groups towards the CPU (port
0).
Eliminate the race in two steps:
1. Grab the write-side lock of the MDB while generating the replay
list.
This prevents new memberships from showing up while we are generating
the replay list. But it leaves the scenario in which a deferred event
was already generated, but not delivered, before we grabbed the
lock. Therefore:
2. Make sure that no deferred version of a replay event is already
enqueued to the switchdev deferred queue, before adding it to the
replay list, when replaying additions.
Fixes: 4f2673b3a2b6 ("net: bridge: add helper to replay port and host-joined mdb entries") Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
JAZZ_ESP is a bool kconfig symbol that selects SCSI_SPI_ATTRS. When
CONFIG_SCSI=m, this results in SCSI_SPI_ATTRS=m while JAZZ_ESP=y, which
causes many undefined symbol linker errors.
Fix this by only offering to build this driver when CONFIG_SCSI=y.
[mkp: JAZZ_ESP is unique in that it does not support being compiled as a
module unlike the remaining SPI SCSI HBA drivers]
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20240214055953.9612-1-rdunlap@infradead.org Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: linux-mips@vger.kernel.org Cc: Arnd Bergmann <arnd@arndb.de> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Nicolas Schier <nicolas@fjasle.eu> Cc: James E.J. Bottomley <jejb@linux.ibm.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: linux-scsi@vger.kernel.org Cc: Geert Uytterhoeven <geert@linux-m68k.org> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402112222.Gl0udKyU-lkp@intel.com/ Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Correct blk-mq registration issue with module parameter
disable_managed_interrupts enabled.
When we turn off the default PCI_IRQ_AFFINITY flag, the driver needs to
register with blk-mq using blk_mq_map_queues(). The driver is currently
calling blk_mq_pci_map_queues() which results in a stack trace and possibly
undefined behavior.
The bpf_doc script refers to the GPL as the "GNU Privacy License".
I strongly suspect that the author wanted to refer to the GNU General
Public License, under which the Linux kernel is released, as, to the
best of my knowledge, there is no license named "GNU Privacy License".
This patch corrects the license name in the script accordingly.
Fixes: 56a092c89505 ("bpf: add script and prepare bpf.h for new helpers documentation") Signed-off-by: Gianmarco Lusvardi <glusvardi@posteo.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Quentin Monnet <quentin@isovalent.com> Link: https://lore.kernel.org/bpf/20240213230544.930018-3-glusvardi@posteo.net Signed-off-by: Sasha Levin <sashal@kernel.org>
xsk_build_skb() allocates a page and adds it to the skb via
skb_add_rx_frag() and specifies 0 for truesize. This leads to a warning
in skb_add_rx_frag() with CONFIG_DEBUG_NET enabled because size is
larger than truesize.
Increasing truesize requires to add the same amount to socket's
sk_wmem_alloc counter in order not to underflow the counter during
release in the destructor (sock_wfree()).
Pass the size of the allocated page as truesize to skb_add_rx_frag().
Add this mount to socket's sk_wmem_alloc counter.
Fixes: cf24f5a5feea ("xsk: add support for AF_XDP multi-buffer on Tx path") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Link: https://lore.kernel.org/bpf/20240202163221.2488589-1-bigeasy@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
Correct the names given to a few of the GPIO pins. The original names
were unknowingly based on the header from a pre-production board. The
production board has a slightly different pin assignment for the 40-pin
GPIO header.
Fixes: 3900160e164b ("arm64: dts: rockchip: Add Indiedroid Nova board") Signed-off-by: Chris Morgan <macromorgan@hotmail.com> Link: https://lore.kernel.org/r/20240125201943.90476-2-macroalpha82@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The px30 has two spi controllers with two chip-selects each.
The num-cs property is specified as the total number of chip
selects a controllers has and is used since 2020 to find uses
of chipselects outside that range in the Rockchip spi driver.
Without the property set, the default is 1, so spi devices
using the second chipselect will not be created.
For small bitmaps that aren't PAGE_SIZE aligned *and* that are less than
512 pages in bitmap length, use an extra page to be able to cover the
entire range e.g. [1M..3G] which would be iterated more efficiently in a
single iteration, rather than two.
iova_bitmap_mapped_length() don't deal correctly with the small bitmaps
(< 2M bitmaps) when the starting address isn't u64 aligned, leading to
skipping a tiny part of the IOVA range. This is materialized as not
marking data dirty that should otherwise have been.
Fix that by using a u8 * in the internal state of IOVA bitmap. Most of the
data structures use the type of the bitmap to adjust its indexes, thus
changing the type of the bitmap decreases the granularity of the bitmap
indexes.
Dirty IOMMU hugepages reported on a base page page-size granularity can
lead to an attempt to set dirty pages in the bitmap beyond the limits that
are pinned.
Bounds check the page index of the array we are trying to access is within
the limits before we kmap() and return otherwise.
While it is also a defensive check, this is also in preparation to defer
setting bits (outside the mapped range) to the next iteration(s) when the
pages become available.
When the range parsing was open-coded the number of u32 entries to
parse had to be a multiple of 4 and the driver checks this. With
the range parsing converted to the range parser the counting changes
from individual u32 entries to a complete range, so the check must
not reject counts not divisible by 4.
Make loading ib_srpt with this parameter set work. The current behavior is
that setting that parameter while loading the ib_srpt kernel module
triggers the following kernel crash:
The CQ shadow read threshold is currently not set for GEN 2. This could
cause an invalid CQ overflow condition, so remove the GEN check that
exclused GEN 1.
UART4 is used as CM7 coprocessor debug UART and may not be accessible from
Linux in case it is protected by RDC. The RDC protection is set up by the
platform firmware. UART4 is not used on this platform by Linux. Disable
UART4 by default to prevent boot hangs, which occur when the RDC protection
is in place.
Fixes: 562d222f23f0 ("arm64: dts: imx8mp: Add support for Data Modul i.MX8M Plus eDM SBC") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
debugfs entries for RRoCE general CC parameters must be exposed only when
they are supported, otherwise when accessing them there may be a syndrome
error in kernel log, for example:
When dma_alloc_coherent fails to allocate dd->cr_base[i].va,
init_credit_return should deallocate dd->cr_base and
dd->cr_base[i] that allocated before. Or those resources
would be never freed and a memleak is triggered.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Link: https://lore.kernel.org/r/20240112085523.3731720-1-alexious@zju.edu.cn Acked-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Extend the bpf_fib_lookup() helper by making it to return the source
IPv4/IPv6 address if the BPF_FIB_LOOKUP_SRC flag is set.
For example, the following snippet can be used to derive the desired
source IP address:
struct bpf_fib_lookup p = { .ipv4_dst = ip4->daddr };
ret = bpf_skb_fib_lookup(skb, p, sizeof(p),
BPF_FIB_LOOKUP_SRC | BPF_FIB_LOOKUP_SKIP_NEIGH);
if (ret != BPF_FIB_LKUP_RET_SUCCESS)
return TC_ACT_SHOT;
/* the p.ipv4_src now contains the source address */
The inability to derive the proper source address may cause malfunctions
in BPF-based dataplanes for hosts containing netdevs with more than one
routable IP address or for multi-homed hosts.
For example, Cilium implements packet masquerading in BPF. If an
egressing netdev to which the Cilium's BPF prog is attached has
multiple IP addresses, then only one [hardcoded] IP address can be used for
masquerading. This breaks connectivity if any other IP address should have
been selected instead, for example, when a public and private addresses
are attached to the same egress interface.
The change was tested with Cilium [1].
Nikolay Aleksandrov helped to figure out the IPv6 addr selection.
[1]: https://github.com/cilium/cilium/pull/28283
Signed-off-by: Martynas Pumputis <m@lambda.lt> Link: https://lore.kernel.org/r/20231007081415.33502-2-m@lambda.lt Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Cc: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error message buffer overflow 'dc->links' 12 <= 12 suggests that the
code is trying to access an element of the dc->links array that is
beyond its bounds. In C, arrays are zero-indexed, so an array with 12
elements has valid indices from 0 to 11. Trying to access dc->links[12]
would be an attempt to access the 13th element of a 12-element array,
which is a buffer overflow.
To fix this, ensure that the loop does not go beyond the last valid
index when accessing dc->links[i + 1] by subtracting 1 from the loop
condition.
This would ensure that i + 1 is always a valid index in the array.
In this case, there is not a problem because the enumerated types are
basically treated as '#define' values. Add an explicit cast to an
integral type to silence the warning.
Address static checker warning in cifs_ses_get_chan_index():
warn: variable dereferenced before check 'server'
To be consistent, and reduce risk, we should add another check
for null server pointer.
Fixes: 88675b22d34e ("cifs: do not search for channel if server is terminating") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Shyam Prasad N <sprasad@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is important to have a unique (sub)test name in TAP, because some CI
environments drop tests with duplicated name.
Some 'cestab' subtests from the diag selftest had the same names, e.g.:
....chk 0 cestab
Now the previous value is taken, to have different names, e.g.:
....chk 2->0 cestab after flush
While at it, the 'after flush' info is added, similar to what is done
with the 'in use' subtests. Also inspired by these 'in use' subtests,
'many' is displayed instead of a large number:
many msk socket present [ ok ]
....chk many msk in use [ ok ]
....chk many cestab [ ok ]
....chk many->0 msk in use after flush [ ok ]
....chk many->0 cestab after flush [ ok ]
Fixes: 81ab772819da ("selftests: mptcp: diag: check CURRESTAB counters") Cc: stable@vger.kernel.org Reviewed-by: Geliang Tang <geliang@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the 'Fixes' commit mentioned below, the command that is executed
in __chk_nr() helper can return nothing if the feature is not supported.
This is the case when the MPTCP CURRESTAB counter is not supported.
To avoid this warning ...
./diag.sh: line 65: [: !=: unary operator expected
... we just need to surround '$nr' with double quotes, to support an
empty string when the feature is not supported.
Fixes: 81ab772819da ("selftests: mptcp: diag: check CURRESTAB counters") Cc: stable@vger.kernel.org Reviewed-by: Geliang Tang <geliang@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a new helper chk_msk_cestab() to check the current
established connections counter MIB_CURRESTAB in diag.sh. Invoke it
to check the counter during the connection after every chk_msk_inuse().
Signed-off-by: Geliang Tang <geliang.tang@linux.dev> Reviewed-by: Matthieu Baerts <matttbe@kernel.org> Signed-off-by: Matthieu Baerts <matttbe@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the 'Fixes' commit mentioned below, and if the kernel being tested
doesn't support the 'fullmesh' flag, this error will be printed:
netlink error -22 (Invalid argument)
./pm_nl_ctl: bailing out due to netlink error[s]
But that can be normal if the kernel doesn't support the feature, no
need to print this worrying error message while everything else looks
OK. So we can mute stderr. Failures will still be detected if any.
Fixes: 1dc88d241f92 ("selftests: mptcp: pm_nl_ctl: always look for errors") Cc: stable@vger.kernel.org Reviewed-by: Geliang Tang <geliang@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>