The variable temp is incorrectly being updated, instead it should
be offset otherwise the loop just reads the same capability value
and loops forever. Thanks to Alan Stern for pointing out the
correct fix to my original fix. Fix also cleans up clang warning:
drivers/usb/host/ehci-dbg.c:840:4: warning: Value stored to 'temp'
is never read
Fixes: d49d43174400 ("USB: misc ehci updates") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There used to be an integer overflow check in proc_do_submiturb() but
we removed it. It turns out that it's still required. The
uurb->buffer_length variable is a signed integer and it's controlled by
the user. It can lead to an integer overflow when we do:
Promote a variable keeping track of USB transfer memory usage to a
wider data type and allow for higher bandwidth transfers from a large
number of USB devices connected to a single host.
Sometimes the USB device gets confused about the state of the initialization and
the connection fails. In particular, the device thinks that it's already set up
and running while the host thinks the device still needs to be configured. To
work around this issue, power-cycle the hub's output to issue a sort of "reset"
to the device. This makes the device restart its state machine and then the
initialization succeeds.
This fixes problems where the kernel reports a list of errors like this:
usb 1-1.3: device not accepting address 19, error -71
The end result is a non-functioning device. After this patch, the sequence
becomes like this:
usb 1-1.3: new high-speed USB device number 18 using ci_hdrc
usb 1-1.3: device not accepting address 18, error -71
usb 1-1.3: new high-speed USB device number 19 using ci_hdrc
usb 1-1.3: device not accepting address 19, error -71
usb 1-1-port3: attempt power cycle
usb 1-1.3: new high-speed USB device number 21 using ci_hdrc
usb-storage 1-1.3:1.2: USB Mass Storage device detected
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device will be used in future Amazon EC2 instances as the primary
serial port (i.e., data sent to this port will be available via the
GetConsoleOuput [1] EC2 API).
We've been adding this as a quirk on a per device basis hoping that
newer disk enclosures would do better, but that has not happened,
so simply apply this quirk to all Seagate devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hash_setup function always sets the hash_setup_done flag, even
when the hash algorithm is invalid. This prevents the default hash
algorithm defined as CONFIG_IMA_DEFAULT_HASH from being used.
This patch sets hash_setup_done flag only for valid hash algorithms.
Fixes: e7a2ad7eb6f4 "ima: enable support for larger default filedata hash algorithms" Signed-off-by: Boshi Wang <wangboshi@huawei.com> Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com> Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some ->page_mkwrite handlers may return VM_FAULT_RETRY as its return
code (GFS2 or Lustre can definitely do this). However VM_FAULT_RETRY
from ->page_mkwrite is completely unhandled by the mm code and results
in locking and writeably mapping the page which definitely is not what
the caller wanted.
Fix Lustre and block_page_mkwrite_ret() used by other filesystems
(notably GFS2) to return VM_FAULT_NOPAGE instead which results in
bailing out from the fault code, the CPU then retries the access, and we
fault again effectively doing what the handler wanted.
Link: http://lkml.kernel.org/r/20170203150729.15863-1-jack@suse.cz Signed-off-by: Jan Kara <jack@suse.cz> Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Reviewed-by: Jinshan Xiong <jinshan.xiong@intel.com> Cc: Matthew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tipc_server_stop(), we iterate over the connections with limiting
factor as server's idr_in_use. We ignore the fact that this variable
is decremented in tipc_close_conn(), leading to premature exit.
In this commit, we iterate until the we have no connections left.
Acked-by: Ying Xue <ying.xue@windriver.com> Acked-by: Jon Maloy <jon.maloy@ericsson.com> Tested-by: John Thompson <thompa.atl@gmail.com> Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison on the timeout can lead to an array overrun
read on sctp_timer_tbl because of an off-by-one error. Fix
this by using < instead of <= and also compare to the array
size rather than SCTP_EVENT_TIMEOUT_MAX.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the server reboots multiple times, the client should rely on the
server to tell it that it cannot reclaim state as per section 9.6.3.4
in RFC7530 and section 8.4.2.1 in RFC5661.
Currently, the client is being to conservative, and is assuming that
if the server reboots while state recovery is in progress, then it must
ignore state that was not recovered before the reboot.
ipddp_route structs contain alignment padding so kernel heap memory
is leaked when they are copied to user space in
ipddp_ioctl(SIOCFINDIPDDPRT). Change kmalloc() to kzalloc() to clear
that memory.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vti6 interface is registered before the rtnl_link_ops block
is attached. As a result the resulting RTM_NEWLINK is missing
IFLA_INFO_KIND. Re-order attachment of rtnl_link_ops block to fix.
Signed-off-by: Dave Forster <dforster@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP1510, OMAP5910 and OMAP310 have only 9 logical channels.
OMAP1610, OMAP5912, OMAP1710, OMAP730, and OMAP850 have 16 logical channels
available.
The wired 17 for the lch_count must have been used to cover the 16 + 1
dedicated LCD channel, in reality we can only use 9 or 16 channels.
The d->chan_count is not used by the omap-dma stack, so we can skip the
setup. chan_count was configured to the number of logical channels and not
the actual number of physical channels anyways.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Command perf test -v 16 (Setup struct perf_event_attr test) always
reports success even if the test case fails. It works correctly if you
also specify -F (for don't fork).
root@s35lp76 perf]# ./perf test -v 16
15: Setup struct perf_event_attr :
--- start ---
running './tests/attr/test-record-no-delay'
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB /tmp/tmp4E1h7R/perf.data
(1 samples) ]
expected task=0, got 1
expected precise_ip=0, got 3
expected wakeup_events=1, got 0
FAILED './tests/attr/test-record-no-delay' - match failure
test child finished with 0
---- end ----
Setup struct perf_event_attr: Ok
The reason for the wrong error reporting is the return value of the
system() library call. It is called in run_dir() file tests/attr.c and
returns the exit status, in above case 0xff00.
This value is given as parameter to the exit() function which can only
handle values 0-0xff.
The child process terminates with exit value of 0 and the parent does
not detect any error.
This patch corrects the error reporting and prints the correct test
result.
When kernel configuration SMP,PREEMPT and DEBUG_PREEMPT are enabled,
echo 1 >/proc/sys/kernel/sysrq
echo p >/proc/sysrq-trigger
kernel will print call trace as below:
This can be seen on a common board like an r-pi3.
This happens because when echo p >/proc/sysrq-trigger,
get_irq_regs() is called outside of IRQ context,
if preemption is enabled in this situation,kernel will
print the call trace. Since many prior discussions on
the mailing lists have made it clear that get_irq_regs
either just returns NULL or stale data when used outside
of IRQ context,we simply avoid calling it outside of
IRQ context.
This driver's ->rs485_config callback checks if SER_RS485_RTS_ON_SEND
and SER_RS485_RTS_AFTER_SEND have the same value. If they do, it means
the user has passed in invalid data with the TIOCSRS485 ioctl()
since RTS must have a different polarity when sending and when not
sending. In this case, rs485 mode is not enabled (the RS485_URA bit
is not set in the RS485 Enable Register) and this is supposed to be
signaled back to the user by clearing the SER_RS485_ENABLED bit in
struct serial_rs485 ... except a missing tilde character is preventing
that from happening.
Fixes: 28e3fb6c4dce ("serial: Add support for Fintek F81216A LPC to 4 UART") Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Cc: "Ji-Ze Hong (Peter Hong)" <hpeter@gmail.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we send a read request and hit the clean data in cache device, there
is a situation called cache read race in bcache(see the commit in the tail
of cache_look_up(), the following explaination just copy from there):
The bucket we're reading from might be reused while our bio is in flight,
and we could then end up reading the wrong data. We guard against this
by checking (in bch_cache_read_endio()) if the pointer is stale again;
if so, we treat it as an error (s->iop.error = -EINTR) and reread from
the backing device (but we don't pass that error up anywhere)
It should be noted that cache read race happened under normal
circumstances, not the circumstance when SSD failed, it was counted
and shown in /sys/fs/bcache/XXX/internal/cache_read_races.
Without this patch, when we use writeback mode, we will never reread from
the backing device when cache read race happened, until the whole cache
device is clean, because the condition
(s->recoverable && (dc && !atomic_read(&dc->has_dirty))) is false in
cached_dev_read_error(). In this situation, the s->iop.error(= -EINTR)
will be passed up, at last, user will receive -EINTR when it's bio end,
this is not suitable, and wield to up-application.
In this patch, we use s->read_dirty_data to judge whether the read
request hit dirty data in cache device, it is safe to reread data from
the backing device when the read request hit clean data. This can not
only handle cache read race, but also recover data when failed read
request from cache device.
[edited by mlyle to fix up whitespace, commit log title, comment
spelling]
Fixes: d59b23795933 ("bcache: only permit to recovery read error when cache device is clean") Signed-off-by: Hua Rui <huarui.dev@gmail.com> Reviewed-by: Michael Lyle <mlyle@lyle.org> Reviewed-by: Coly Li <colyli@suse.de> Signed-off-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When bcache does read I/Os, for example in writeback or writethrough mode,
if a read request on cache device is failed, bcache will try to recovery
the request by reading from cached device. If the data on cached device is
not synced with cache device, then requester will get a stale data.
For critical storage system like database, providing stale data from
recovery may result an application level data corruption, which is
unacceptible.
With this patch, for a failed read request in writeback or writethrough
mode, recovery a recoverable read request only happens when cache device
is clean. That is to say, all data on cached device is up to update.
For other cache modes in bcache, read request will never hit
cached_dev_read_error(), they don't need this patch.
Please note, because cache mode can be switched arbitrarily in run time, a
writethrough mode might be switched from a writeback mode. Therefore
checking dc->has_data in writethrough mode still makes sense.
Changelog:
V4: Fix parens error pointed by Michael Lyle.
v3: By response from Kent Oversteet, he thinks recovering stale data is a
bug to fix, and option to permit it is unnecessary. So this version
the sysfs file is removed.
v2: rename sysfs entry from allow_stale_data_on_failure to
allow_stale_data_on_failure, and fix the confusing commit log.
v1: initial patch posted.
[small change to patch comment spelling by mlyle]
Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Michael Lyle <mlyle@lyle.org> Reported-by: Arne Wolf <awolf@lenovo.com> Reviewed-by: Michael Lyle <mlyle@lyle.org> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: Nix <nix@esperi.org.uk> Cc: Kai Krakow <hurikhan77@gmail.com> Cc: Eric Wheeler <bcache@lists.ewheeler.net> Cc: Junhui Tang <tang.junhui@zte.com.cn> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hardware always writes one or two bytes in the index portion of
an indexed transfer. Make sure the message we send as the index
doesn't have a zero length.
Cc: Daniel Kurtz <djkurtz@chromium.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Fixes: 56f9eac05489 ("drm/i915/intel_i2c: use INDEX cycles for i2c read transactions") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171123194157.25367-3-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit bb9e0d4bca50f429152e74a459160b41f3d60fb2) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can only specify the one slave address to indexed reads/writes.
Make sure the messages we check are destined to the same slave
address before deciding to do an indexed transfer.
Cc: Daniel Kurtz <djkurtz@chromium.org> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sean Paul <seanpaul@chromium.org> Fixes: 56f9eac05489 ("drm/i915/intel_i2c: use INDEX cycles for i2c read transactions") Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20171123194157.25367-2-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit c4deb62d7821672265b87952bcd1c808f3bf3e8f) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For correct close-to-open semantics, NFS must validate
the change attribute of a directory (or file) on open.
Since commit ecf3d1f1aa74 ("vfs: kill FS_REVAL_DOT by adding a
d_weak_revalidate dentry op"), open() of "." or a path ending ".." is
not revalidated reliably (except when that direct is a mount point).
Prior to that commit, "." was revalidated using nfs_lookup_revalidate()
which checks the LOOKUP_OPEN flag and forces revalidation if the flag is
set.
Since that commit, nfs_weak_revalidate() is used for NFSv3 (which
ignores the flags) and nothing is used for NFSv4.
This is fixed by using nfs_lookup_verify_inode() in
nfs_weak_revalidate(). This does the revalidation exactly when needed.
Also, add a definition of .d_weak_revalidate for NFSv4.
The incorrect behavior is easily demonstrated by running "echo *" in
some non-mountpoint NFS directory while watching network traffic.
Without this patch, "echo *" sometimes doesn't produce any traffic.
With the patch it always does.
Fixes: ecf3d1f1aa74 ("vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op")
cc: stable@vger.kernel.org (3.9+) Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During panel removal or system shutdown panel_simple_disable() is called
which disables the panel backlight but the panel is still powered due to
missing calls to panel_simple_unprepare().
Sometimes, a processor might execute an instruction while another
processor is updating the page tables for that instruction's code page,
but before the TLB shootdown completes. The interesting case happens
if the page is in the TLB.
In general, the processor will succeed in executing the instruction and
nothing bad happens. However, what if the instruction is an MMIO access?
If *that* happens, KVM invokes the emulator, and the emulator gets the
updated page tables. If the update side had marked the code page as non
present, the page table walk then will fail and so will x86_decode_insn.
Unfortunately, even though kvm_fetch_guest_virt is correctly returning
X86EMUL_PROPAGATE_FAULT, x86_decode_insn's caller treats the failure as
a fatal error if the instruction cannot simply be reexecuted (as is the
case for MMIO). And this in fact happened sometimes when rebooting
Windows 2012r2 guests. Just checking ctxt->have_exception and injecting
the exception if true is enough to fix the case.
Thanks to Eduardo Habkost for helping in the debugging of this issue.
Reported-by: Yanan Fu <yfu@redhat.com> Cc: Eduardo Habkost <ehabkost@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instruction emulation after trapping a #UD exception can result in an
MMIO access, for example when emulating a MOVBE on a processor that
doesn't support the instruction. In this case, the #UD vmexit handler
must exit to user mode, but there wasn't any code to do so. Add it for
both VMX and SVM.
Signed-off-by: Liran Alon <liran.alon@oracle.com> Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Wanpeng Li <wanpeng.li@hotmail.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We discovered a box that had double allocations, and suspected the space
cache may be to blame. While auditing the write out path I noticed that
if we've already setup the space cache we will just carry on. This
means that any error we hit after cache_save_setup before we go to
actually write the cache out we won't reset the inode generation, so
whatever was already written will be considered correct, except it'll be
stale. Fix this by _always_ resetting the generation on the block group
inode, this way we only ever have valid or invalid cache.
With this patch I was no longer able to reproduce cache corruption with
dm-log-writes and my bpf error injection tool.
Signed-off-by: Josef Bacik <jbacik@fb.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MADVISE_WILLNEED has always been a noop for DAX (formerly XIP) mappings.
Unfortunately madvise_willneed() doesn't communicate this information
properly to the generic madvise syscall implementation. The calling
convention is quite subtle there. madvise_vma() is supposed to either
return an error or update &prev otherwise the main loop will never
advance to the next vma and it will keep looping for ever without a way
to get out of the kernel.
It seems this has been broken since introduction. Nobody has noticed
because nobody seems to be using MADVISE_WILLNEED on these DAX mappings.
[mhocko@suse.com: rewrite changelog] Link: http://lkml.kernel.org/r/20171127115318.911-1-guoxuenan@huawei.com Fixes: fe77ba6f4f97 ("[PATCH] xip: madvice/fadvice: execute in place") Signed-off-by: chenjie <chenjie6@huawei.com> Signed-off-by: guoxuenan <guoxuenan@huawei.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Minchan Kim <minchan@kernel.org> Cc: zhangyi (F) <yi.zhang@huawei.com> Cc: Miao Xie <miaoxie@huawei.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: Shaohua Li <shli@fb.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: David Rientjes <rientjes@google.com> Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Cc: Carsten Otte <cotte@de.ibm.com> Cc: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we unconditionally make page table dirty in touch_pmd().
It may result in false-positive can_follow_write_pmd().
We may avoid the situation, if we would only make the page table entry
dirty if caller asks for write access -- FOLL_WRITE.
The patch also changes touch_pud() in the same way.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[Salvatore Bonaccorso: backport for 3.16:
- Adjust context
- Drop specific part for PUD-sized transparent hugepages. Support
for PUD-sized transparent hugepages was added in v4.11-rc1
] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An independent security researcher, Mohamed Ghannam, has reported
this vulnerability to Beyond Security's SecuriTeam Secure Disclosure
program.
The xfrm_dump_policy_done function expects xfrm_dump_policy to
have been called at least once or it will crash. This can be
triggered if a dump fails because the target socket's receive
buffer is full.
This patch fixes it by using the cb->start mechanism to ensure that
the initialisation is always done regardless of the buffer situation.
Fixes: 12a169e7d8f4 ("ipsec: Put dumpers on the dump list") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The start callback allows the caller to set up a context for the
dump callbacks. Presumably, the context can then be destroyed in
the done callback.
Signed-off-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When accessing Xenstore in a transaction the user is specifying a
transaction id which he normally obtained from Xenstore when starting
the transaction. Xenstore is validating a transaction id against all
known transaction ids of the connection the request came in. As all
requests of a domain not being the one where Xenstore lives share
one connection, validation of transaction ids of different users of
Xenstore in that domain should be done by the kernel of that domain
being the multiplexer between the Xenstore users in that domain and
Xenstore.
In order to prohibit one Xenstore user "hijacking" a transaction from
another user the xenbus driver has to verify a given transaction id
against all known transaction ids of the user before forwarding it to
Xenstore.
s390 version of commit 334bb7738764 ("x86/kbuild: enable modversions
for symbols exported from asm") so we get also rid of all these
warnings:
WARNING: EXPORT symbol "_mcount" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "memcpy" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "memmove" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "memset" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "save_fpu_regs" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "sie64a" [vmlinux] version generation failed, symbol will not be versioned.
WARNING: EXPORT symbol "sie_exit" [vmlinux] version generation failed, symbol will not be versioned.
Protect against corrupt firmware files by ensuring that the length we
get for the data in a region actually lies within the available firmware
file data buffer.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In function btrfs_uuid_tree_iterate(), errno is assigned to variable ret
on errors. However, it directly returns 0. It may be better to return
ret. This patch also removes the warning, because the caller already
prints a warning.
At the end of function ad7150_write_event_config(), directly returns 0.
As a result, the errors will be ignored by the callers. It may be better
to return variable "ret".
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, kernel sends NEW_PEER_CANDIDATE event to user land even if
the found peer does not have any room to accept other peer. This causes
continuous connection trials.
mesh_sync_offset_adjust_tbtt() implements Extensible synchronization
framework ([1] 13.13.2 Extensible synchronization framework). It shall
not operate the flag "TBTT Adjusting subfield" ([1] 8.4.2.100.8 Mesh
Capability), since it is used only for MBCA ([1] 13.13.4 Mesh beacon
collision avoidance, see 13.13.4.4.3 TBTT scanning and adjustment
procedures for detail). So this patch remove the flag operations.
[1] IEEE Std 802.11 2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[remove adjusting_tbtt entirely, since it's now unused] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting shutup when the action is HDA_FIXUP_ACT_PRE_PROBE might
not have the desired effect since it could be overridden by
another more generic shutup function. Prevent this by setting
the more specific shutup function on HDA_FIXUP_ACT_PROBE.
I reported the include issue for tracepoints a while ago, but nothing
seems to have happened. Now it bit us, since the drm_mm_print
conversion was broken for armada. Fix it, so I can re-enable armada
in the drm-misc build configs.
v2: Rebase just the compile fix on top of Chris' build fix.
Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1483115932-19584-1-git-send-email-daniel.vetter@ffwll.ch Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a few cases the err-variable is not set to a negative error code if a
function call in typhoon_init_one() fails and thus 0 is returned
instead.
It may be better to set err to the appropriate negative error
code before returning.
Reported-by: Pan Bian <bianpan2016@163.com> Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de> Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases the return value of a failing function is not being used
and the function typhoon_init_one() returns another negative error code
instead.
Signed-off-by: Thomas Preisner <thomas.preisner+linux@fau.de> Signed-off-by: Milan Stephan <milan.stephan+linux@fau.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously we didn't check the type of device before trying to apply Type 1
(PCI-X) or Type 2 (PCIe) Setting Records from _HPX.
We don't support PCI-X Setting Records, so this was harmless, but the
warning was useless.
We do support PCIe Setting Records, and we didn't check whether a device
was PCIe before applying settings. I don't think anything bad happened on
non-PCIe devices because pcie_capability_clear_and_set_word(),
pcie_cap_has_lnkctl(), etc., would fail before doing any harm. But it's
ugly to depend on those internals.
Check the device type before attempting to apply Type 1 and Type 2 Setting
Records (Type 0 records are applicable to PCI, PCI-X, and PCIe devices).
A side benefit is that this prevents useless "not supported" warnings when
a BIOS supplies a Type 1 (PCI-X) Setting Record and we try to apply it to
every single device:
pci 0000:00:00.0: PCI-X settings not supported
After this patch, we'll get the warning only when a BIOS supplies a Type 1
record and we have a PCI-X device to which it should be applied.
The first message to a remote node should prompt a new
connection even if it is RDMA operation. For RDMA operation
the MR mapping can fail because connections is not yet up.
Since the connection establishment is asynchronous,
we make sure the map failure because of unavailable
connection reach to the user by appropriate error code.
Before returning to the user, lets trigger the connection
so that its ready for the next retry.
link_active = !hw->mac.get_link_status
/* link_active is false, wrongly */
This problem arises because the single flag get_link_status is used to
signal two different states: link status needs checking and link status is
down.
Avoid the problem by using the return value of .check_for_link to signal
the link status to e1000e_has_link().
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca> Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error from e1e_rphy(), the loop will exit early and "success"
will be set to true erroneously.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is based on upstream commit 10e840dfb0b7, which did not touch the
iio-trig-periodic-rtc driver because it has been removed upstream.
The following explanation comes from that commit:
These stand-alone trigger drivers were using iio_trigger_put()
where they should have been using iio_trigger_free(). The
iio_trigger_put() adds a module_put which is bad since they
never did a module_get.
In the sysfs driver, module_get/put's are used as triggers are
added & removed. This extra module_put() occurs on an error path
in the probe routine (probably rare).
In the bfin-timer & interrupt trigger drivers, the module resources
are not explicitly managed, so it's doing a put on something that
was never get'd. It occurs on the probe error path and on the
remove path (not so rare).
Tested with the sysfs trigger driver.
The bfin & interrupt drivers were build tested & inspected only.
This was build tested only.
Cc: Alison Schofield <amsfield22@gmail.com> Cc: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Thu, 23 Nov 2017 15:20:05 +0000 (16:20 +0100)]
USB: fix buffer overflows with parsing CDC headers
Parsing CDC headers a buffer overflow cannot just be prevented
by checking that the remainder of the buffer is longer than minimum
length. The size of the fields to be parsed must be figured in, too.
In newer kernels this issue has been fixed at a central location with
When mtdoops calls mtd_panic_write(), it eventually calls
panic_nand_write() in nand_base.c. In order to properly wait for the
nand chip to be ready in panic_nand_wait(), the chip must first be
selected.
When using the atmel nand flash controller, a panic would occur due to
a NULL pointer exception.
Fixes: 2af7c6539931 ("mtd: Add panic_write for NAND flashes") Signed-off-by: Brent Taylor <motobud@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because userspace gets Very Unhappy when calls like stat() and execve()
return -EINTR on 9p filesystem mounts. For instance, when bash is
looking in PATH for things to execute and some SIGCHLD interrupts
stat(), bash can throw a spurious 'command not found' since it doesn't
retry the stat().
In practice, hitting the problem is rare and needs a really
slow/bogged down 9p server.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VIDIOC_DQEVENT and VIDIOC_QUERY_EXT_CTRL should give the same output for
the control flags field.
This patch creates a new function user_flags(), that calculates the user
exported flags value (which is different than the kernel internal flags
structure). This function is then used by all the code that exports the
internal flags to userspace.
Let's allocate the the structure dynamically so we can get the firmware
loaded correctly:
[ 14.243057] as10x_usb: firmware: as102_data1_st.hex loaded with success
[ 14.500777] as10x_usb: firmware: as102_data2_st.hex loaded with success
When a uprobe is installed on an instruction that we currently do not
emulate, we copy the instruction into a xol buffer and single step
that instruction. If that instruction generates a fault, we abort the
single stepping before invoking the signal handler. Once the signal
handler is done, the uprobe trap is hit again since the instruction is
retried and the process repeats.
We use uprobe_deny_signal() to detect if the xol instruction triggered
a signal. If so, we clear TIF_SIGPENDING and set TIF_UPROBE so that the
signal is not handled until after the single stepping is aborted. In
this case, uprobe_deny_signal() returns true and get_signal() ends up
returning 0. However, in do_signal(), we are not looking at the return
value, but depending on ksig.sig for further action, all with an
uninitialized ksig that is not touched in this scenario. Fix the same
by initializing ksig.sig to 0.
Fixes: 129b69df9c90 ("powerpc: Use get_signal() signal_setup_done()") Reported-by: Anton Blanchard <anton@samba.org> Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As noted by Christoph Biedl, passing a pointer size of 4 in the new CAS
implementation causes a kernel crash. The attached patch corrects the
off by one error in the argument validity check.
In reviewing the code, I noticed that we only perform word operations
with the pointer size argument. The subi instruction intentionally uses
a word condition on 64-bit kernels. Nullification was used instead of a
cmpib instruction as the branch should never be taken. The shlw
pseudo-operation generates a depw,z instruction and it clears the target
before doing a shift left word deposit. Thus, we don't need to clip the
upper 32 bits of this argument on 64-bit kernels.
Tested with a gcc testsuite run with a 64-bit kernel. The gcc atomic
code in libgcc is the only direct user of the new CAS implementation
that I am aware of.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes an issue seen on Power systems with ixgbe which results
in skb list corruption and an eventual kernel oops. The following is what
was observed:
CPU 1 CPU2
============================ ============================
1: ixgbe_xmit_frame_ring ixgbe_clean_tx_irq
2: first->skb = skb eop_desc = tx_buffer->next_to_watch
3: ixgbe_tx_map read_barrier_depends()
4: wmb check adapter written status bit
5: first->next_to_watch = tx_desc napi_consume_skb(tx_buffer->skb ..);
6: writel(i, tx_ring->tail);
The read_barrier_depends is insufficient to ensure that tx_buffer->skb does not
get loaded prior to tx_buffer->next_to_watch, which then results in loading
a stale skb pointer. This patch replaces the read_barrier_depends with
smp_rmb to ensure loads are ordered with respect to the load of
tx_buffer->next_to_watch.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with fm10k as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40evf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with ixgbevf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igbvf as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with igb as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original issue being fixed in this patch was seen with the ixgbe
driver, but the same issue exists with i40e as well, as the code is
very similar. read_barrier_depends is not sufficient to ensure
loads following it are not speculatively loaded out of order
by the CPU, which can result in stale data being loaded, causing
potential system crashes.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two issues were found on an IMX6 development board without an
enabled RTC device(resulting in the boot time and monotonic
time being initialized to 0).
Issue 1:exportfs -a generate:
"exportfs: /opt/nfs/arm does not support NFS export"
Issue 2:cat /proc/stat:
"btime 4294967236"
The same issues can be reproduced on x86 after running the
following code:
int main(void)
{
struct timeval val;
int ret;
Two issues are different symptoms of same problem:
The reason is a positive wall_to_monotonic pushes boot time back
to the time before Epoch, and getboottime will return negative
value.
In symptom 1:
negative boot time cause get_expiry() to overflow time_t
when input expire time is 2147483647, then cache_flush()
always clears entries just added in ip_map_parse.
In symptom 2:
show_stat() uses "unsigned long" to print negative btime
value returned by getboottime.
This patch fix the problem by prohibiting time from being set to a value which
would cause a negative boot time. As a result one can't set the CLOCK_REALTIME
time prior to (1970 + system uptime).
Cc: Prarit Bhargava <prarit@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Wang YanQing <udknight@gmail.com>
[jstultz: reworded commit message]
[msfjarvis: Backport to 3.18 as we are missing the do_settimeofday64
function the upstream commit patches, so we apply the changes to
do_settimeofday] Signed-off-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Harsh Shandilya <msfjarvis@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A recent change fixing NFC device allocation itself introduced an
error-handling bug by returning an error pointer in case device-id
allocation failed. This is clearly broken as the callers still expected
NULL to be returned on errors as detected by Dan's static checker.
Fix this up by returning NULL in the event that we've run out of memory
when allocating a new device id.
Note that the offending commit is marked for stable (3.8) so this fix
needs to be backported along with it.
Fixes: 20777bc57c34 ("NFC: fix broken device allocation") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix child node-lookup during probe, which ended up searching the whole
device tree depth-first starting at parent rather than just matching on
its children.
Note that the original premature free of the parent node has already
been fixed separately, but that fix was apparently never backported to
stable.
Fixes: 9ac33b0ce81f ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)") Fixes: 660e15519399 ("clk: ti: dra7-atl-clock: Fix of_node reference counting") Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_find_node_by_name() will call of_node_put() on the node so we need to
get it first to avoid warnings.
The cfg_node needs to be put after we have finished processing the
properties.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Nishanth Menon <nm@ti.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For many years some users of assigned devices have reported worse
performance on AMD processors with NPT than on AMD without NPT,
Intel or bare metal.
The reason turned out to be that SVM is discarding the guest PAT
setting and uses the default (PA0=PA4=WB, PA1=PA5=WT, PA2=PA6=UC-,
PA3=UC). The guest might be using a different setting, and
especially might want write combining but isn't getting it
(instead getting slow UC or UC- accesses).
Thanks a lot to geoff@hostfission.com for noticing the relation
to the g_pat setting. The patch has been tested also by a bunch
of people on VFIO users forums.
Fixes: 709ddebf81cb40e3c36c6109a7892e8b93a09464 Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=196409 Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: David Hildenbrand <david@redhat.com> Tested-by: Nick Sarnie <commendsarnex@gmail.com> Signed-off-by: Radim Krčmář <rkrcmar@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a se_cmd->cmd_kref reference leak that can
occur when a non immediate TMR is proceeded our of command
sequence number order, and CMDSN_LOWER_THAN_EXP is returned
by iscsit_sequence_cmd().
To address this bug, call target_put_sess_cmd() during this
special case following what iscsit_process_scsi_cmd() does
upon CMDSN_LOWER_THAN_EXP.
Cc: Mike Christie <mchristi@redhat.com> Cc: Hannes Reinecke <hare@suse.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fd2421f54423 ("fs/9p: When doing inode lookup compare qid details
and inode mode bits.") transformed v9fs_qid_iget() to use iget5_locked()
instead of iget_locked(). However, the test() callback is not checking
fid.path at all, which means that a lookup in the inode cache can now
accidentally locate a completely wrong inode from the same inode hash
bucket if the other fields (qid.type and qid.version) match.
Fixes: fd2421f54423 ("fs/9p: When doing inode lookup compare qid details and inode mode bits.") Reviewed-by: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some timer compat ioctls have NULL checks of timer instance with
snd_BUG_ON() that bring up WARN_ON() when the debug option is set.
Actually the condition can be met in the normal situation and it's
confusing and bad to spew kernel warnings with stack trace there.
Let's remove snd_BUG_ON() invocation and replace with the simple
checks. Also, correct the error code to EBADFD to follow the native
ioctl error handling.
The helper functions to parse and look for the clock source, selector
and multiplier unit may return the descriptor with a too short length
than required, while there is no sanity check in the caller side.
Add some sanity checks in the parsers, at least, to guarantee the
given descriptor size, for avoiding the potential crashes.
The usb-audio driver may trigger an out-of-bound access at parsing a
malformed selector unit, as it checks the header length only after
evaluating bNrInPins field, which can be already above the given
length. Fix it by adding the length check beforehand.
When the usb-audio descriptor contains the malformed feature unit
description with a too short length, the driver may access
out-of-bounds. Add a sanity check of the header size at the beginning
of parse_audio_feature_unit().
Fixes: 23caaf19b11e ("ALSA: usb-mixer: Add support for Audio Class v2.0") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there are pending writes subject to delayed allocation, then i_size
will show size after the writes have completed, while i_disksize
contains the value of i_size on the disk (since the writes have not
been persisted to disk).
If fallocate(2) is called with the FALLOC_FL_KEEP_SIZE flag, either
with or without the FALLOC_FL_ZERO_RANGE flag set, and the new size
after the fallocate(2) is between i_size and i_disksize, then after a
crash, if a journal commit has resulted in the changes made by the
fallocate() call to be persisted after a crash, but the delayed
allocation write has not resolved itself, i_size would not be updated,
and this would cause the following e2fsck complaint:
Inode 12, end of extent exceeds allowed value
(logical block 33, physical block 33441, len 7)
This can only take place on a sparse file, where the fallocate(2) call
is allocating blocks in a range which is before a pending delayed
allocation write which is extending i_size. Since this situation is
quite rare, and the window in which the crash must take place is
typically < 30 seconds, in practice this condition will rarely happen.
Nevertheless, it can be triggered in testing, and in particular by
xfstests generic/456.
If a delegation has been revoked by the server, operations using that
delegation should error out with NFS4ERR_DELEG_REVOKED in the >4.1
case, and NFS4ERR_BAD_STATEID otherwise.
The server needs NFSv4.1 clients to explicitly free revoked delegations.
If the server returns NFS4ERR_DELEG_REVOKED, the client will do that;
otherwise it may just forget about the delegation and be unable to
recover when it later sees SEQ4_STATUS_RECALLABLE_STATE_REVOKED set on a
SEQUENCE reply. That can cause the Linux 4.1 client to loop in its
stage manager.
Signed-off-by: Andrew Elble <aweits@rit.edu> Reviewed-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nfs4_get_referral is wiping out any cached attributes with what was
returned via GETATTR(fs_locations), but the bit mask for that
operation does not request any file attributes.
Retrieve owner and timestamp information so that the memcpy in
nfs4_get_referral fills in more attributes.
Changes since v1:
- Don't request attributes that the client unconditionally replaces
- Request only MOUNTED_ON_FILEID or FILEID attribute, not both
- encode_fs_locations() doesn't use the third bitmask word
Fixes: 6b97fd3da1ea ("NFSv4: Follow a referral") Suggested-by: Pradeep Thomas <pradeepthomas@gmail.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isofs uses a 'char' variable to load the number of years since
1900 for an inode timestamp. On architectures that use a signed
char type by default, this results in an invalid date for
anything beyond 2027.
This changes the function argument to a 'u8' array, which
is defined the same way on all architectures, and unambiguously
lets us use years until 2155.
This should be backported to all kernels that might still be
in use by that date.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In bcache code, sysfs entries are created before all resources get
allocated, e.g. allocation thread of a cache set.
There is posibility for NULL pointer deference if a resource is accessed
but which is not initialized yet. Indeed Jorg Bornschein catches one on
cache set allocation thread and gets a kernel oops.
The reason for this bug is, when bch_bucket_alloc() is called during
cache set registration and attaching, ca->alloc_thread is not properly
allocated and initialized yet, call wake_up_process() on ca->alloc_thread
triggers NULL pointer deference failure. A simple and fast fix is, before
waking up ca->alloc_thread, checking whether it is allocated, and only
wake up ca->alloc_thread when it is not NULL.
Signed-off-by: Coly Li <colyli@suse.de> Reported-by: Jorg Bornschein <jb@capsec.org> Cc: Kent Overstreet <kent.overstreet@gmail.com> Reviewed-by: Michael Lyle <mlyle@lyle.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition between nilfs_dirty_inode() and
nilfs_set_file_dirty().
When a file is opened, nilfs_dirty_inode() is called to update the
access timestamp in the inode. It calls __nilfs_mark_inode_dirty() in a
separate transaction. __nilfs_mark_inode_dirty() caches the ifile
buffer_head in the i_bh field of the inode info structure and marks it
as dirty.
After some data was written to the file in another transaction, the
function nilfs_set_file_dirty() is called, which adds the inode to the
ns_dirty_files list.
Then the segment construction calls nilfs_segctor_collect_dirty_files(),
which goes through the ns_dirty_files list and checks the i_bh field.
If there is a cached buffer_head in i_bh it is not marked as dirty
again.
Since nilfs_dirty_inode() and nilfs_set_file_dirty() use separate
transactions, it is possible that a segment construction that writes out
the ifile occurs in-between the two. If this happens the inode is not
on the ns_dirty_files list, but its ifile block is still marked as dirty
and written out.
In the next segment construction, the data for the file is written out
and nilfs_bmap_propagate() updates the b-tree. Eventually the bmap root
is written into the i_bh block, which is not dirty, because it was
written out in another segment construction.
As a result the bmap update can be lost, which leads to file system
corruption. Either the virtual block address points to an unallocated
DAT block, or the DAT entry will be reused for something different.
The error can remain undetected for a long time. A typical error
message would be one of the "bad btree" errors or a warning that a DAT
entry could not be found.
This bug can be reproduced reliably by a simple benchmark that creates
and overwrites millions of 4k files.
Link: http://lkml.kernel.org/r/1509367935-3086-2-git-send-email-konishi.ryusuke@lab.ntt.co.jp Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net> Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Tested-by: Andreas Rohner <andreas.rohner@gmx.net> Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently if the autofs kernel module gets an error when writing to the
pipe which links to the daemon, then it marks the whole moutpoint as
catatonic, and it will stop working.
It is possible that the error is transient. This can happen if the
daemon is slow and more than 16 requests queue up. If a subsequent
process tries to queue a request, and is then signalled, the write to
the pipe will return -ERESTARTSYS and autofs will take that as total
failure.
So change the code to assess -ERESTARTSYS and -ENOMEM as transient
failures which only abort the current request, not the whole mountpoint.
It isn't a crash or a data corruption, but having autofs mountpoints
suddenly stop working is rather inconvenient.
Ian said:
: And given the problems with a half dozen (or so) user space applications
: consuming large amounts of CPU under heavy mount and umount activity this
: could happen more easily than we expect.
Link: http://lkml.kernel.org/r/87y3norvgp.fsf@notabene.neil.brown.name Signed-off-by: NeilBrown <neilb@suse.com> Acked-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a commit 7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
regression, then activated by commit 6a9c001b7ec3 ("MIPS: Switch ELF
core dumper to use regsets.)", that caused n32 processes to dump o32
core files by failing to set the EF_MIPS_ABI2 flag in the ELF core file
header's `e_flags' member:
statement placed in arch/mips/kernel/binfmt_elfn32.c, however in the
regset case, i.e. when CORE_DUMP_USE_REGSET is set, ELF_CORE_EFLAGS is
no longer used by `fill_note_info' in fs/binfmt_elf.c, and instead the
`->e_flags' member of the regset view chosen is. We have the views
defined in arch/mips/kernel/ptrace.c, however only an o32 and an n64
one, and the latter is used for n32 as well. Consequently an o32 core
file is incorrectly dumped from n32 processes (the ELF32 vs ELF64 class
is chosen elsewhere, and the 32-bit one is correctly selected for n32).
Correct the issue then by defining an n32 regset view and using it as
appropriate. Issue discovered in GDB testing.
Fixes: 7aeb753b5353 ("MIPS: Implement task_user_regset_view.") Signed-off-by: Maciej W. Rozycki <macro@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Djordje Todorovic <djordje.todorovic@rt-rk.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/17617/ Signed-off-by: James Hogan <jhogan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug can be easily triggered, if an extra delay (e.g. 10ms) is added
between the test of DMF_FREEING & DMF_DELETING and dm_get() in
dm_get_from_kobject().
To fix it, we need to ensure the test of DMF_FREEING & DMF_DELETING and
dm_get() are done in an atomic way, so _minor_lock is used.
The other callers of dm_get() have also been checked to be OK: some
callers invoke dm_get() under _minor_lock, some callers invoke it under
_hash_lock, and dm_start_request() invoke it after increasing
md->open_count.
Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The default max_cache_size_bytes for dm-bufio is meant to be the lesser
of 25% of the size of the vmalloc area and 2% of the size of lowmem.
However, on 32-bit systems the intermediate result in the expression
overflows, causing the wrong result to be computed. For example, on a
32-bit system where the vmalloc area is 520093696 bytes, the result is 1174405 rather than the expected 130023424, which makes the maximum
cache size much too small (far less than 2% of lowmem). This causes
severe performance problems for dm-verity users on affected systems.
Fix this by using mult_frac() to correctly multiply by a percentage. Do
this for all places in dm-bufio that multiply by a percentage. Also
replace (VMALLOC_END - VMALLOC_START) with VMALLOC_TOTAL, which contrary
to the comment is now defined in include/linux/vmalloc.h.
Depends-on: 9993bc635 ("sched/x86: Fix overflow in cyc2ns_offset") Fixes: 95d402f057f2 ("dm: add bufio") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log