Current MMC driver doesn't handle generic error (bit19 of device
status) in write sequence. As a result, write data gets lost when
generic error occurs. For example, a generic error when updating a
filesystem management information causes a loss of write data and
corrupts the filesystem. In the worst case, the system will never
boot.
This patch includes the following functionality:
1. To enable error checking for the response of CMD12 and CMD13
in write command sequence
2. To retry write sequence when a generic error occurs
Messages are added for v2 to show what occurs.
[Backported to 3.4-stable]
Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp> Signed-off-by: Chris Ball <cjb@laptop.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 8c4f3c3fa9681 "ftrace: Check module functions being traced on reload"
fixed module loading and unloading with respect to function tracing, but
it missed the function graph tracer. If you perform the following
The above mentioned commit didn't go far enough. Well, it covered the
function tracer by adding checks in __register_ftrace_function(). The
problem is that the function graph tracer circumvents that (for a slight
efficiency gain when function graph trace is running with a function
tracer. The gain was not worth this).
The problem came with ftrace_startup() which should always be called after
__register_ftrace_function(), if you want this bug to be completely fixed.
Anyway, this solution moves __register_ftrace_function() inside of
ftrace_startup() and removes the need to call them both.
Reported-by: Dave Wysochanski <dwysocha@redhat.com> Fixes: ed926f9b35cd ("ftrace: Use counters to enable functions to trace") Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It was finally narrowed down to unloading a module that was being traced.
It was actually more than that. When functions are being traced, there's
a table of all functions that have a ref count of the number of active
tracers attached to that function. When a function trace callback is
registered to a function, the function's record ref count is incremented.
When it is unregistered, the function's record ref count is decremented.
If an inconsistency is detected (ref count goes below zero) the above
warning is shown and the function tracing is permanently disabled until
reboot.
The ftrace callback ops holds a hash of functions that it filters on
(and/or filters off). If the hash is empty, the default means to filter
all functions (for the filter_hash) or to disable no functions (for the
notrace_hash).
When a module is unloaded, it frees the function records that represent
the module functions. These records exist on their own pages, that is
function records for one module will not exist on the same page as
function records for other modules or even the core kernel.
Now when a module unloads, the records that represents its functions are
freed. When the module is loaded again, the records are recreated with
a default ref count of zero (unless there's a callback that traces all
functions, then they will also be traced, and the ref count will be
incremented).
The problem is that if an ftrace callback hash includes functions of the
module being unloaded, those hash entries will not be removed. If the
module is reloaded in the same location, the hash entries still point
to the functions of the module but the module's ref counts do not reflect
that.
With the help of Steve and Joern, we found a reproducer:
Using uinput module and uinput_release function.
cd /sys/kernel/debug/tracing
modprobe uinput
echo uinput_release > set_ftrace_filter
echo function > current_tracer
rmmod uinput
modprobe uinput
# check /proc/modules to see if loaded in same addr, otherwise try again
echo nop > current_tracer
[BOOM]
The above loads the uinput module, which creates a table of functions that
can be traced within the module.
We add uinput_release to the filter_hash to trace just that function.
Enable function tracincg, which increments the ref count of the record
associated to uinput_release.
Remove uinput, which frees the records including the one that represents
uinput_release.
Load the uinput module again (and make sure it's at the same address).
This recreates the function records all with a ref count of zero,
including uinput_release.
Disable function tracing, which will decrement the ref count for uinput_release
which is now zero because of the module removal and reload, and we have
a mismatch (below zero ref count).
The solution is to check all currently tracing ftrace callbacks to see if any
are tracing any of the module's functions when a module is loaded (it already does
that with callbacks that trace all functions). If a callback happens to have
a module function being traced, it increments that records ref count and starts
tracing that function.
There may be a strange side effect with this, where tracing module functions
on unload and then reloading a new module may have that new module's functions
being traced. This may be something that confuses the user, but it's not
a big deal. Another approach is to disable all callback hashes on module unload,
but this leaves some ftrace callbacks that may not be registered, but can
still have hashes tracing the module's function where ftrace doesn't know about
it. That situation can cause the same bug. This solution solves that case too.
Another benefit of this solution, is it is possible to trace a module's
function on unload and load.
Link: http://lkml.kernel.org/r/20130705142629.GA325@redhat.com Reported-by: Jörn Engel <joern@logfs.org> Reported-by: Dave Jones <davej@redhat.com> Reported-by: Steve Hodgson <steve@purestorage.com> Tested-by: Steve Hodgson <steve@purestorage.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
[bwh: Backported to 3.2: adjust context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There are two types of hashes in the ftrace_ops; one type
is the filter_hash and the other is the notrace_hash. Either
one may be null, meaning it has no elements. But when elements
are added, the hash is allocated.
Throughout the code, a check needs to be made to see if a hash
exists or the hash has elements, but the check if the hash exists
is usually missing causing the possible "NULL pointer dereference bug".
Add a helper routine called "ftrace_hash_empty()" that returns
true if the hash doesn't exist or its count is zero. As they mean
the same thing.
Last-bug-reported-by: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When disabling the "notrace" records, that means we want to trace them.
If the notrace_hash is zero, it means that we want to trace all
records. But to disable a zero notrace_hash means nothing.
The check for the notrace_hash count was incorrect with:
if (hash && !hash->count)
return
With the correct comment above it that states that we do nothing
if the notrace_hash has zero count. But !hash also means that
the notrace hash has zero count. I think this was done to
protect against dereferencing NULL. But if !hash is true, then
we go through the following loop without doing a single thing.
Fix it to:
if (!hash || !hash->count)
return;
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We don't validate iph->ihl which may lead a dead loop if we meet a IPIP
skb whose iph->ihl is zero. Fix this by failing immediately when iph->ihl
is evil (less than 5).
Cc: Eric Dumazet <edumazet@google.com> Cc: Petr Matousek <pmatouse@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: the affected code is in __skb_get_rxhash()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
It appears that driver runs into a problem here if fibsize is too small
because we allocate user_srbcmd with fibsize size only but later we
access it until user_srbcmd->sg.count to copy it over to srbcmd.
It is not correct to test (fibsize < sizeof(*user_srbcmd)) because this
structure already includes one sg element and this is not needed for
commands without data. So, we would recommend to add the following
(instead of test for fibsize == 0).
If we do a zero size allocation then it will oops. Also we can't be
sure the user passes us a NUL terminated string so I've added a
terminator.
This code can only be triggered by root.
Reported-by: Nico Golde <nico@ngolde.de> Reported-by: Fabian Yamaguchi <fabs@goesec.de> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The {get,put}_user macros don't perform range checking on the provided
__user address when !CPU_HAS_DOMAINS.
This patch reworks the out-of-line assembly accessors to check the user
address against a specified limit, returning -EFAULT if is is out of
range.
[will: changed get_user register allocation to match put_user]
[rmk: fixed building on older ARM architectures]
Reported-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[bwh: Backported to 3.2: TUSER() was called T()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The iommu integration into memory slots expects memory slots to be
added or removed and doesn't handle the move case. We can unmap
slots from the iommu after we mark them invalid and map them before
installing the final memslot array. Also re-order the kmemdup vs
map so we don't leave iommu mappings if we get ENOMEM.
Reviewed-by: Gleb Natapov <gleb@redhat.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Stephan Mueller reported to me recently a error in random number generation in
the ansi cprng. If several small requests are made that are less than the
instances block size, the remainder for loop code doesn't increment
rand_data_valid in the last iteration, meaning that the last bytes in the
rand_data buffer gets reused on the subsequent smaller-than-a-block request for
random data.
The fix is pretty easy, just re-code the for loop to make sure that
rand_data_valid gets incremented appropriately
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Reported-by: Stephan Mueller <stephan.mueller@atsec.com> CC: Stephan Mueller <stephan.mueller@atsec.com> CC: Petr Matousek <pmatouse@redhat.com> CC: Herbert Xu <herbert@gondor.apana.org.au> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When working on report indexes, always validate that they are in bounds.
Without this, a HID device could report a malicious feature report that
could trick the driver into a heap overflow:
[ 634.885003] usb 1-1: New USB device found, idVendor=0596, idProduct=0500
...
[ 676.469629] BUG kmalloc-192 (Tainted: G W ): Redzone overwritten
Note that we need to change the indexes from s8 to s16 as they can
be between -1 and 255.
CVE-2013-2897
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[bwh: Backported to 3.2: mt_device::{cc,cc_value,inputmode}_index do not
exist and the corresponding indices do not need to be validated.
mt_device::maxcontact_report_id does not exist either. So all we need
to do is to widen mt_device::inputmode.] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
commit a553e4a6317b2cfc7659542c10fe43184ffe53da ("[PKTGEN]: IPSEC support")
tried to support IPsec ESP transport transformation for pktgen, but acctually
this doesn't work at all for two reasons(The orignal transformed packet has
bad IPv4 checksum value, as well as wrong auth value, reported by wireshark)
- After transpormation, IPv4 header total length needs update,
because encrypted payload's length is NOT same as that of plain text.
- After transformation, IPv4 checksum needs re-caculate because of payload
has been changed.
With this patch, armmed pktgen with below cofiguration, Wireshark is able to
decrypted ESP packet generated by pktgen without any IPv4 checksum error or
auth value error.
pgset "flag IPSEC"
pgset "flows 1"
Signed-off-by: Fan Du <fan.du@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
IPv6 stats are 64 bits and thus are protected with a seqlock. By not
disabling bottom-half we could deadlock here if we don't disable bh and
a softirq reentrantly updates the same mib.
Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently we're using plain spin_lock() in prb_shutdown_retire_blk_timer(),
however the timer might fire right in the middle and thus try to re-aquire
the same spinlock, leaving us in a endless loop.
To fix that, use the spin_lock_bh() to block it.
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.") CC: "David S. Miller" <davem@davemloft.net> CC: Daniel Borkmann <dborkman@redhat.com> CC: Willem de Bruijn <willemb@google.com> CC: Phil Sutter <phil@nwl.cc> CC: Eric Dumazet <edumazet@google.com> Reported-by: Jan Stancek <jstancek@redhat.com> Tested-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Acked-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Salam reported a use after free bug in PF_PACKET that occurs when
we're sending out frames on a socket bound device and suddenly the
net device is being unregistered. It appears that commit 827d9780
introduced a possible race condition between {t,}packet_snd() and
packet_notifier(). In the case of a bound socket, packet_notifier()
can drop the last reference to the net_device and {t,}packet_snd()
might end up suddenly sending a packet over a freed net_device.
To avoid reverting 827d9780 and thus introducing a performance
regression compared to the current state of things, we decided to
hold a cached RCU protected pointer to the net device and maintain
it on write side via bind spin_lock protected register_prot_hook()
and __unregister_prot_hook() calls.
In {t,}packet_snd() path, we access this pointer under rcu_read_lock
through packet_cached_dev_get() that holds reference to the device
to prevent it from being freed through packet_notifier() while
we're in send path. This is okay to do as dev_put()/dev_hold() are
per-cpu counters, so this should not be a performance issue. Also,
the code simplifies a bit as we don't need need_rls_dev anymore.
Fixes: 827d978037d7 ("af-packet: Use existing netdev reference for bound sockets.") Reported-by: Salam Noureddine <noureddine@aristanetworks.com> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com> Cc: Ben Greear <greearb@candelatech.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
--------------------------- cut here -------------------------------
The reason is that when the bridge dev's address is changed, the
br_fdb_change_mac_address() will add new address in fdb, but when
the bridge was removed, the address entry in the fdb did not free,
the bridge_fdb_cache still has objects when destroy the cache, Fix
this by flushing the bridge address entry when removing the bridge.
v2: according to the Toshiaki Makita and Vlad's suggestion, I only
delete the vlan0 entry, it still have a leak here if the vlan id
is other number, so I need to call fdb_delete_by_port(br, NULL, 1)
to flush all entries whose dst is NULL for the bridge.
Suggested-by: Toshiaki Makita <toshiaki.makita1@gmail.com> Suggested-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: Ding Tianhong <dingtianhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
tried to fix a problem with VLAN devices and promiscuouse flag setting.
The issue was that VLAN device was setting a flag on an interface that
was down, thus resulting in bad promiscuity count.
This commit blocked flag propagation to any device that is currently
down.
fixed VLAN code to only propagate flags when the VLAN interface is up,
thus fixing the same issue as above, only localized to VLAN.
The problem we have now is that if we have create a complex stack
involving multiple software devices like bridges, bonds, and vlans,
then it is possible that the flags would not propagate properly to
the physical devices. A simple examle of the scenario is the
following:
eth0----> bond0 ----> bridge0 ---> vlan50
If bond0 or eth0 happen to be down at the time bond0 is added to
the bridge, then eth0 will never have promisc mode set which is
currently required for operation as part of the bridge. As a
result, packets with vlan50 will be dropped by the interface.
The only 2 devices that implement the special flag handling are
VLAN and DSA and they both have required code to prevent incorrect
flag propagation. As a result we can remove the generic solution
introduced in b6c40d68ff6498b7f63ddf97cf0aa818d748dee7 and leave
it to the individual devices to decide whether they will block
flag propagation or not.
Reported-by: Stefan Priebe <s.priebe@profihost.ag> Suggested-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
init_card() calls dev_get_by_name() to get a network deceive. But it
doesn't decrease network device reference count after the device is
used.
Signed-off-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Offenders don't have port numbers, so set it to 0.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If kmsg->msg_namelen > sizeof(struct sockaddr_storage) then in the
original code that would lead to memory corruption in the kernel if you
had audit configured. If you didn't have audit configured it was
harmless.
There are some programs such as beta versions of Ruby which use too
large of a buffer and returning an error code breaks them. We should
clamp the ->msg_namelen value instead.
Fixes: 1661bf364ae9 ("net: heap overflow in __audit_sockaddr()") Reported-by: Eric Wong <normalperson@yhbt.net> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Tested-by: Eric Wong <normalperson@yhbt.net> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit bceaa90240b6019ed73b49965eac7d167610be69 ("inet: prevent leakage
of uninitialized memory to user in recv syscalls") conditionally updated
addr_len if the msg_name is written to. The recv_error and rxpmtu
functions relied on the recvmsg functions to set up addr_len before.
As this does not happen any more we have to pass addr_len to those
functions as well and set it to the size of the corresponding sockaddr
length.
This broke traceroute and such.
Fixes: bceaa90240b6 ("inet: prevent leakage of uninitialized memory to user in recv syscalls") Reported-by: Brad Spengler <spender@grsecurity.net> Reported-by: Tom Labanowski Cc: mpb <mpb.mail@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In that case it is probable that kernel code overwrote part of the
stack. So we should bail out loudly here.
The BUG_ON may be removed in future if we are sure all protocols are
conformant.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Only update *addr_len when we actually fill in sockaddr, otherwise we
can return uninitialized memory from the stack to the caller in the
recvfrom, recvmmsg and recvmsg syscalls. Drop the the (addr_len == NULL)
checks because we only get called with a valid addr_len pointer either
from sock_common_recvmsg or inet_recvmsg.
If a blocking read waits on a socket which is concurrently shut down we
now return zero and set msg_msgnamelen to 0.
Reported-by: mpb <mpb.mail@gmail.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
ip4_datagram_connect() being called from process context,
it should use IP_INC_STATS() instead of IP_INC_STATS_BH()
otherwise we can deadlock on 32bit arches, or get corruptions of
SNMP counters.
Fixes: 584bdf8cbdf6 ("[IPV4]: Fix "ipOutNoRoutes" counter error for TCP and UDP") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dave Jones <davej@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In af3e095a1fb4, Erik Jacobsen fixed one type of unaligned access
bug for ia64 by converting a 64-bit write to use put_unaligned().
Unfortunately, since gcc will convert a short memset() to a series
of appropriately-aligned stores, the problem is now visible again
on tilegx, where the memset that zeros out proc_event is converted
to three 64-bit stores, causing an unaligned access panic.
A better fix for the original problem is to ensure that proc_event
is aligned to 8 bytes here. We can do that relatively easily by
arranging to start the struct cn_msg aligned to 8 bytes and then
offset by 4 bytes. Doing so means that the immediately following
proc_event structure is then correctly aligned to 8 bytes.
The result is that the memset() stores are now aligned, and as an
added benefit, we can remove the put_unaligned() calls in the code.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
These strings come from a copy_from_user() and there is no way to be
sure they are NUL terminated.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes two race conditions between bond_store_updelay/downdelay
and bond_store_miimon which could lead to division by zero as miimon can
be set to 0 while either updelay/downdelay are being set and thus miss the
zero check in the beginning, the zero div happens because updelay/downdelay
are stored as new_value / bond->params.miimon. Use rtnl to synchronize with
miimon setting.
CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com> Acked-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If priority/traffic class field in IPv6 header is set (seen when
using ssh), the uncompression sets the TC and Flow fields incorrectly.
Example:
This is IPv6 header of a sent packet. Note the priority/TC (=1) in
the first byte.
00000000: 61 00 00 00 00 2c 06 40 fe 80 00 00 00 00 00 00 00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00 00000020: 02 1e ab ff fe 4c 52 57
This gets compressed like this in the sending side
00000000: 72 31 04 06 02 1e ab ff fe 4c 52 57 ec c2 00 16 00000010: aa 2d fe 92 86 4e be c6 ....
In the receiving end, the packet gets uncompressed to this
IPv6 header
00000000: 60 06 06 02 00 2a 1e 40 fe 80 00 00 00 00 00 00 00000010: 02 02 72 ff fe c6 42 10 fe 80 00 00 00 00 00 00 00000020: ab ff fe 4c 52 57 ec c2
First four bytes are set incorrectly and we have also lost
two bytes from destination address.
The fix is to switch the case values in switch statement
when checking the TC field.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently the ARP monitoring is not supported with 802.3ad, and it's
prohibited to use it via the module params.
However we still can set it afterwards via sysfs, cause we only check for
*LB modes there.
To fix this - add a check for 802.3ad mode in bonding_store_arp_interval.
CC: Jay Vosburgh <fubar@us.ibm.com> CC: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Veaceslav Falico <vfalico@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For properly initialising the Tausworthe generator [1], we have
a strict seeding requirement, that is, s1 > 1, s2 > 7, s3 > 15.
Commit 697f8d0348 ("random32: seeding improvement") introduced
a __seed() function that imposes boundary checks proposed by the
errata paper [2] to properly ensure above conditions.
However, we're off by one, as the function is implemented as:
"return (x < m) ? x + m : x;", and called with __seed(X, 1),
__seed(X, 7), __seed(X, 15). Thus, an unwanted seed of 1, 7, 15
would be possible, whereas the lower boundary should actually
be of at least 2, 8, 16, just as GSL does. Fix this, as otherwise
an initialization with an unwanted seed could have the effect
that Tausworthe's PRNG properties cannot not be ensured.
Note that this PRNG is *not* used for cryptography in the kernel.
Fixes: 697f8d0348a6 ("random32: seeding improvement") Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Florian Weimer <fweimer@redhat.com> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As the rfc 4191 said, the Router Preference and Lifetime values in a
::/0 Route Information Option should override the preference and lifetime
values in the Router Advertisement header. But when the kernel deals with
a ::/0 Route Information Option, the rt6_get_route_info() always return
NULL, that means that overriding will not happen, because those default
routers were added without flag RTF_ROUTEINFO in rt6_add_dflt_router().
In order to deal with that condition, we should call rt6_get_dflt_router
when the prefix length is 0.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When trying to delete a table >= 256 using iproute2 the local table
will be deleted.
The table id is specified as a netlink attribute when it needs more then
8 bits and iproute2 then sets the table field to RT_TABLE_UNSPEC (0).
Preconditions to matching the table id in the rule delete code
doesn't seem to take the "table id in netlink attribute" into condition
so the frh_get_table helper function never gets to do its job when
matching against current rule.
Use the helper function twice instead of peaking at the table value directly.
Originally reported at: http://bugs.debian.org/724783
Reported-by: Nicolas HICHER <nhicher@avencall.com> Signed-off-by: Andreas Henriksson <andreas@fatal.se> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
arch/um/os-Linux/start_up.c: In function 'check_coredump_limit':
arch/um/os-Linux/start_up.c:338:16: error: storage size of 'lim' isn't known
arch/um/os-Linux/start_up.c:339:2: error: implicit declaration of function 'getrlimit' [-Werror=implicit-function-declaration]
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org> CC: Jeff Dike <jdike@addtoit.com> CC: Richard Weinberger <richard@nod.at> CC: Al Viro <viro@zeniv.linux.org.uk> CC: user-mode-linux-devel@lists.sourceforge.net CC: user-mode-linux-user@lists.sourceforge.net CC: linux-kernel@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
throttle_cfs_rq() doesn't check to make sure that period_timer is running,
and while update_curr/assign_cfs_runtime does, a concurrently running
period_timer on another cpu could cancel itself between this cpu's
update_curr and throttle_cfs_rq(). If there are no other cfs_rqs running
in the tg to restart the timer, this causes the cfs_rq to be stranded
forever.
Fix this by calling __start_cfs_bandwidth() in throttle if the timer is
inactive.
(Also add some sched_debug lines for cfs_bandwidth.)
Tested: make a run/sleep task in a cgroup, loop switching the cgroup
between 1ms/100ms quota and unlimited, checking for timer_active=0 and
throttled=1 as a failure. With the throttle_cfs_rq() change commented out
this fails, with the full patch it passes.
In selinux_ip_postroute() we perform access checks based on the
packet's security label. For locally generated traffic we get the
packet's security label from the associated socket; this works in all
cases except for TCP SYN-ACK packets. In the case of SYN-ACK packet's
the correct security label is stored in the connection's request_sock,
not the server's socket. Unfortunately, at the point in time when
selinux_ip_postroute() is called we can't query the request_sock
directly, we need to recreate the label using the same logic that
originally labeled the associated request_sock.
See the inline comments for more explanation.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Tested-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In selinux_ip_output() we always label packets based on the parent
socket. While this approach works in almost all cases, it doesn't
work in the case of TCP SYN-ACK packets when the correct label is not
the label of the parent socket, but rather the label of the larval
socket represented by the request_sock struct.
Unfortunately, since the request_sock isn't queued on the parent
socket until *after* the SYN-ACK packet is sent, we can't lookup the
request_sock to determine the correct label for the packet; at this
point in time the best we can do is simply pass/NF_ACCEPT the packet.
It must be said that simply passing the packet without any explicit
labeling action, while far from ideal, is not terrible as the SYN-ACK
packet will inherit any IP option based labeling from the initial
connection request so the label *should* be correct and all our
access controls remain in place so we shouldn't have to worry about
information leaks.
Reported-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Tested-by: Janak Desai <Janak.Desai@gtri.gatech.edu> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Under guest controllable circumstances apic_get_tmcct will execute a
divide by zero and cause a crash. If the guest cpuid support
tsc deadline timers and performs the following sequence of requests
the host will crash.
- Set the mode to periodic
- Set the TMICT to 0
- Set the mode bits to 11 (neither periodic, nor one shot, nor tsc deadline)
- Set the TMICT to non-zero.
Then the lapic_timer.period will be 0, but the TMICT will not be. If the
guest then reads from the TMCCT then the host will perform a divide by 0.
This patch ensures that if the lapic_timer.period is 0, then the division
does not occur.
Reported-by: Andrew Honig <ahonig@google.com> Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.2: s/kvm_apic_get_reg/apic_get_reg/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In multiple functions the vcpu_id is used as an offset into a bitfield. Ag
malicious user could specify a vcpu_id greater than 255 in order to set or
clear bits in kernel memory. This could be used to elevate priveges in the
kernel. This patch verifies that the vcpu_id provided is less than 255.
The api documentation already specifies that the vcpu_id must be less than
max_vcpus, but this is currently not checked.
Reported-by: Andrew Honig <ahonig@google.com> Signed-off-by: Andrew Honig <ahonig@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The hugepage code had the exact same bug that regular pages had in
commit 7485d0d3758e ("futexes: Remove rw parameter from
get_futex_key()").
The regular page case was fixed by commit 9ea71503a8ed ("futex: Fix
regression with read only mappings"), but the transparent hugepage case
(added in a5b338f2b0b1: "thp: update futex compound knowledge") case
remained broken.
Found by Dave Jones and his trinity tool.
Reported-and-tested-by: Dave Jones <davej@fedoraproject.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mel Gorman <mgorman@suse.de> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The "rpm * div" operations can overflow here, so this patch adds an
upper limit to rpm to prevent that. Jean Delvare helped me with this
patch.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Roger Lucas <vt8231@hiddenengine.co.uk> Signed-off-by: Jean Delvare <khali@linux-fr.org>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The W83L786NG stores the fan speed on 4 bits while the sysfs interface
uses a 0-255 range. Thus the driver should scale the user input down
to map it to the device range, and scale up the value read from the
device before presenting it to the user. The reserved register nibble
should be left unchanged.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.
If SDRAM is not reset, it causes memory bus congestion and
the device hangs. We put SDRAM in selfresh mode before watchdog
reset, removing potential freezes.
Without this patch PXA270-based ICP DAS LP-8x4x hangs after up to 40
reboots. With this patch it has successfully rebooted 500 times.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com> Tested-by: Marek Vasut <marex@denx.de> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When converting from tosa-keyboard driver to matrix keyboard, tosa keys
received extra 1 column shift. Replace that with correct values to make
keyboard work again.
Fixes: f69a6548c9d5 ('[ARM] pxa/tosa: make use of the matrix keypad driver') Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some module parameters in dm-bufio are read-only. These parameters
inform the user about memory consumption. They are not supposed to be
changed by the user.
However, despite being read-only, these parameters can be set on
modprobe or insmod command line, for example:
modprobe dm-bufio current_allocated_bytes=12345
The kernel doesn't expect that these variables can be non-zero at module
initialization and if the user sets them, it results in BUG.
This patch initializes the variables in the module init routine, so that
user-supplied values are ignored.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
UEFI time services are often broken once we're in virtual mode. We were
already refusing to use them on 64-bit systems, but it turns out that
they're also broken on some 32-bit firmware, including the Dell Venue.
Disable them for now, we can revisit once we have the 1:1 mappings code
incorporated.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com> Link: http://lkml.kernel.org/r/1385754283-2464-1-git-send-email-matthew.garrett@nebula.com Cc: Matt Fleming <matt.fleming@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
[bwh: Backported to 3.2: deleted code is slightly different] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When compiling with icc, <linux/compiler-gcc.h> ends up included
because the icc environment defines __GNUC__. Thus, we neither need
nor want to have this macro defined in both compiler-gcc.h and
compiler-intel.h, and the fact that they are inconsistent just makes
the compiler spew warnings.
Reported-by: Sunil K. Pandey <sunil.k.pandey@intel.com> Cc: Kevin B. Smith <kevin.b.smith@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Link: http://lkml.kernel.org/n/tip-0mbwou1zt7pafij09b897lg3@git.kernel.org
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The dm_round_up function may overflow to zero. In this case,
dm_table_create() must fail rather than go on to allocate an empty array
with alloc_targets().
This fixes a possible memory corruption that could be caused by passing
too large a number in "param->target_count".
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There is a possible leak of snapshot space in case of crash.
The reason for space leaking is that chunks in the snapshot device are
allocated sequentially, but they are finished (and stored in the metadata)
out of order, depending on the order in which copying finished.
For example, supposed that the metadata contains the following records
SUPERBLOCK
METADATA (blocks 0 ... 250)
DATA 0
DATA 1
DATA 2
...
DATA 250
Now suppose that you allocate 10 new data blocks 251-260. Suppose that
copying of these blocks finish out of order (block 260 finished first
and the block 251 finished last). Now, the snapshot device looks like
this:
SUPERBLOCK
METADATA (blocks 0 ... 250, 260, 259, 258, 257, 256)
DATA 0
DATA 1
DATA 2
...
DATA 250
DATA 251
DATA 252
DATA 253
DATA 254
DATA 255
METADATA (blocks 255, 254, 253, 252, 251)
DATA 256
DATA 257
DATA 258
DATA 259
DATA 260
Now, if the machine crashes after writing the first metadata block but
before writing the second metadata block, the space for areas DATA 250-255
is leaked, it contains no valid data and it will never be used in the
future.
This patch makes dm-snapshot complete exceptions in the same order they
were allocated, thus fixing this bug.
Note: when backporting this patch to the stable kernel, change the version
field in the following way:
* if version in the stable kernel is {1, 11, 1}, change it to {1, 12, 0}
* if version in the stable kernel is {1, 10, 0} or {1, 10, 1}, change it
to {1, 10, 2}
Userspace reads the version to determine if the bug was fixed, so the
version change is needed.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When running a 32bit kernel the hda_intel driver is still reporting
a 64bit dma_mask if the HW supports it.
From sound/pci/hda/hda_intel.c:
/* allow 64bit DMA address if supported by H/W */
if ((gcap & ICH6_GCAP_64OK) && !pci_set_dma_mask(pci, DMA_BIT_MASK(64)))
pci_set_consistent_dma_mask(pci, DMA_BIT_MASK(64));
else {
pci_set_dma_mask(pci, DMA_BIT_MASK(32));
pci_set_consistent_dma_mask(pci, DMA_BIT_MASK(32));
}
which means when there is a call to dma_alloc_coherent from
snd_malloc_dev_pages a machine address bigger than 32bit can be returned.
This can be true in particular if running the 32bit kernel as a pv dom0
under the Xen Hypervisor or PAE on bare metal.
The problem is that when calling setup_bdle to program the BLE the
dma_addr_t returned from the dma_alloc_coherent is wrongly truncated
from snd_sgbuf_get_addr if running a 32bit kernel:
where PAGE_MASK in a 32bit kernel is zeroing the upper 32bit af addr.
Without this patch the HW will fetch the 32bit truncated address,
which is not the one obtained from dma_alloc_coherent and will result
to a non working audio but can corrupt host memory at a random location.
5551a34e5aea x86-64, build: Always pass in -mno-sse
we unconditionally added -mno-sse to the main build, to keep newer
compilers from generating SSE instructions from autovectorization.
However, this did not extend to the special environments
(arch/x86/boot, arch/x86/boot/compressed, and arch/x86/realmode/rm).
Add -mno-sse to the compiler command line for these environments, and
add -mno-mmx to all the environments as well, as we don't want a
compiler to generate MMX code either.
This patch also removes a $(cc-option) call for -m32, since we have
long since stopped supporting compilers too old for the -m32 option,
and in fact hardcode it in other places in the Makefiles.
Reported-by: Kevin B. Smith <kevin.b.smith@intel.com> Cc: Sunil K. Pandey <sunil.k.pandey@intel.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Cc: H. J. Lu <hjl.tools@gmail.com> Link: http://lkml.kernel.org/n/tip-j21wzqv790q834n7yc6g80j1@git.kernel.org
[bwh: Backported to 3.2:
- Drop changes to arch/x86/Makefile, which sets these flags earlier
- Adjust context
- Drop changes to arch/x86/realmode/rm/Makefile which doesn't exist] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes corner case when (fp + 4) overflows unsigned long,
for example: fp = 0xFFFFFFFF -> fp + 4 == 3.
Signed-off-by: Konstantin Khlebnikov <k.khlebnikov@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
get_wchan() is lockless. Task may wakeup at any time and change its own stack,
thus each next stack frame may be overwritten and filled with random stuff.
/proc/$pid/stack interface had been disabled for non-current tasks, see [1]
But 'wchan' still allows to trigger stack frame unwinding on volatile stack.
This patch fixes oops in unwind_frame() by adding stack pointer validation on
each step (as x86 code do), unwind_frame() already checks frame pointer.
Also I've found another report of this oops on stackoverflow (irony).
Now that scatterwalk_sg_chain sets the chain pointer bit the sg_page
call in scatterwalk_sg_next hits a BUG_ON when CONFIG_DEBUG_SG is
enabled. Use sg_chain_ptr instead of sg_page on a chain entry.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Alan Cox <alan@linux.intel.com> Reported-by: Leho Kraav <leho@kraav.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch adds a check for USB_STATE_NOTATTACHED to the
hub_port_warm_reset_required() workaround for ports that end up in
Compliance Mode in hub_events() when trying to decide which reset
function to use. Trying to call usb_reset_device() with a NOTATTACHED
device will just fail and leave the port broken.
Signed-off-by: Julius Werner <jwerner@chromium.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
According to WM8731 "PD, Rev 4.9 October 2012" datasheet, when it
works in DSP mode A, LRP = 1, while works in DSP mode B, LRP = 0.
So, fix LRP for DSP mode as the datesheet specification.
Signed-off-by: Bo Shen <voice.shen@atmel.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For MPC8572/MPC8536, the status of GPIOs defined as output
cannot be determined by reading GPDAT register, so the code
use shadow data register instead. But the code may give the
wrong status of GPIOs defined as input under some scenarios:
1. If some pins were configured as inputs and were asserted
high before booting the kernel, the shadow data has been
initialized with those pin values.
2. Some pins have been configured as output first and have
been set to the high value, then reconfigured as input.
The above cases will make the shadow data for those input
pins to be set to high. Then reading the pin status will
always return high even if the actual pin status is low.
The code should eliminate the effects of the shadow data to
the input pins, and the status of those pins should be
read directly from GPDAT.
Acked-by: Scott Wood <scottwood@freescale.com> Acked-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes the CS5 setting on the PL2303 USB-to-serial devices. CS5 has a
value of 0 and the CSIZE setting has been skipped altogether by the enclosing
if. Tested on 3.11.6 and the scope shows the correct output after the fix has
been applied.
Tagged to be added to stable, because it fixes a user visible driver bug and is
simple enough to backport easily.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Old code is cosmetically different] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
FTDI UARTs support only 7 or 8 data bits. Until now the ftdi_sio driver would
only report this limitation for CS6 to dmesg and fail to reflect this fact to
tcgetattr.
This patch reverts the unsupported CSIZE setting and reports the fact with less
severance to dmesg for both CS5 and CS6.
To test the patch it's sufficient to call
stty -F /dev/ttyUSB0 cs5
which will succeed without the patch and report an error with the patch
applied.
As an additional fix this patch ensures that the control request will always
include a data bit size.
Signed-off-by: Colin Leitner <colin.leitner@gmail.com> Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2:
- Old code is cosmetically different
- s/ddev/\&port->dev/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The issue is happened in dual controller configuration. We got the
sysfs warnings when rmmod the ipr module.
enclosure_unregister() in drivers/msic/enclosure.c, call device_unregister()
for each componment deivce, device_unregister() ->device_del()->kobject_del()
->sysfs_remove_dir(). In sysfs_remove_dir(), set kobj->sd = NULL.
For each componment device,
enclosure_component_release()->enclosure_remove_links()->sysfs_remove_link()
in which checking kobj->sd again, it has been set as NULL when doing
device_unregister. So we saw all these sysfs WARNING.
Tested-by: wenxiong@linux.vnet.ibm.com Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
A return value of 1 is interpreted as an error. See pci_driver.
in local_pci_probe(). If you're wondering how this ever could
have worked, it's because it used to be the case that only return
values less than zero were interpreted as failure. But even in
the current kernel if the driver registers its various entry
points with the kernel, and then returns a value which is
interpreted as failure, those registrations aren't undone, so
the driver still mostly works. However, the driver's remove
function wouldn't be called on rmmod, and pci power management
functions wouldn't work. In the case of Smart Array, since it
has a battery backed cache (or else no cache) even if the driver
is not shut down properly as long as there is no outstanding
i/o, nothing too bad happens, which is why it took so long to
notice.
Requesting backport to stable because the change to pci-driver.c
which requires driver probe functions to return 0 occurred between
2.6.35 and 2.6.36 (the pci power management breakage) and again
between 3.7 and 3.8 (pci_dev->driver getting set to NULL in
local_pci_probe() preventing driver remove function from being
called on rmmod.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We inadvertantly discarded the scsi status for aborted commands.
For some commands (e.g. reads from tape drives) these can't be retried,
and if we discarded the scsi status, the scsi mid layer couldn't notice
anything was wrong and the error was not reported.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
which is an access to the 0xb8000 without the PCI offset required to
make it work.
Fixes: cc22b4c18540 ("ARM: set vga memory base at run-time") Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Commit 35f9c09fe (tcp: tcp_sendpages() should call tcp_push() once)
added an internal flag MSG_SENDPAGE_NOTLAST, similar to
MSG_MORE.
algif_hash, algif_skcipher, and udp used MSG_MORE from tcp_sendpages()
and need to see the new flag as identical to MSG_MORE.
This fixes sendfile() on AF_ALG.
v3: also fix udp
Cc: Tom Herbert <therbert@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David S. Miller <davem@davemloft.net> Reported-and-tested-by: Shawn Landden <shawnlandden@gmail.com>
Original-patch: Richard Weinberger <richard@nod.at> Signed-off-by: Shawn Landden <shawn@churchofgit.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
After commit e9e4ea74f06635f2ffc1dffe5ef40c854faa0a90
"net: smc91x: dont't use SMC_outw for fixing up halfword-aligned data"
The Versatile SMSC LAN91C111 is crashing like this:
This is because the macro operations in smc91x.h defined
for Versatile are missing SMC_outsw() as used in this
commit.
The Versatile needs and uses the same accessors as the other
platforms in the first if(...) clause, just switch it to using
that and we have one problem less to worry about.
This includes a hunk of a patch from Will Deacon fixin
the other 32bit platforms as well: Innokom, Ramses, PXA,
PCM027.
Checkpatch complains about spacing, but I have opted to
follow the style of this .h-file.
Cc: Russell King <linux@arm.linux.org.uk> Cc: Nicolas Pitre <nico@fluxnic.net> Cc: Eric Miao <eric.y.miao@gmail.com> Cc: Jonathan Cameron <jic23@cam.ac.uk> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In case of error, the function kthread_run() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
There are cases when cryptlen can be zero in crypto_ccm_auth():
-encryptiom: input scatterlist length is zero (no plaintext)
-decryption: input scatterlist contains only the mac
plus the condition of having different source and destination buffers
(or else scatterlist length = max(plaintext_len, ciphertext_len)).
These are not handled correctly, leading to crashes like:
Some s390 crypto algorithms incorrectly use the crypto_tfm structure to
store private data. As the tfm can be shared among multiple threads, this
can result in data corruption.
This patch fixes aes-xts by moving the xts and pcc parameter blocks from
the tfm onto the stack (48 + 96 bytes).
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
[bwh: Backported to 3.2: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The scatterwalk_crypto_chain function invokes the scatterwalk_sg_chain
function to chain two scatterlists, but the chain pointer indication
bit is not set. When the resulting scatterlist is used, for example,
by sg_nents to count the number of scatterlist entries, a segfault occurs
because sg_nents does not follow the chain pointer to the chained scatterlist.
Update scatterwalk_sg_chain to set the chain pointer indication bit as is
done by the sg_chain function.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When performing an asynchronous ablkcipher operation the authenc
completion callback routine is invoked, but it does not locate and use
the proper IV.
The callback routine, crypto_authenc_encrypt_done, is updated to use
the same method of calculating the address of the IV as is done in
crypto_authenc_encrypt function which sets up the callback.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Which reports that we take mems_allowed_seq with interrupts enabled. A
little digging found that this can only be from
cpuset_change_task_nodemask().
This is an actual deadlock because an interrupt doing an allocation will
hit get_mems_allowed()->...->__read_seqcount_begin(), which will spin
forever waiting for the write side to complete.
Cc: John Stultz <john.stultz@linaro.org> Cc: Mel Gorman <mgorman@suse.de> Reported-by: Juri Lelli <juri.lelli@gmail.com> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Tested-by: Juri Lelli <juri.lelli@gmail.com> Acked-by: Li Zefan <lizefan@huawei.com> Acked-by: Mel Gorman <mgorman@suse.de> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Since commit 110dd8f19df5 "[SCSI] libsas: fix scr_read/write users and
update the libata documentation" we have been passing pmp=1 and is_cmd=0
to ata_tf_to_fis(). Praveen reports that eSATA attached drives do not
discover correctly. His investigation found that the BIOS was passing
pmp=0 while Linux was passing pmp=1 and failing to discover the drives.
Update libsas to follow the libata example of pulling the pmp setting
from the ata_link and correct is_cmd to be 1 since all tf's submitted
through ->qc_issue are commands. Presumably libsas lldds do not care
about is_cmd as they have sideband mechanisms to perform link
management.
New tracepoints have been added that have allowed for NULL pointers
being assigned to strings. To fix this, change the TRACE_EVENT() code
to check for NULL and if it is, it will assign "(null)" to it instead
(similar to what glibc printf does).
When the system enters suspend, it disables all interrupts in
suspend_device_irqs(), including the interrupts marked EARLY_RESUME.
On the resume side things are different. The EARLY_RESUME interrupts
are reenabled in sys_core_ops->resume and the non EARLY_RESUME
interrupts are reenabled in the normal system resume path.
When suspend_noirq() failed or suspend is aborted for any other
reason, we might omit the resume side call to sys_core_ops->resume()
and therefor the interrupts marked EARLY_RESUME are not reenabled and
stay disabled forever.
To solve this, enable all irqs unconditionally in irq_resume()
regardless whether interrupts marked EARLY_RESUMEhave been already
enabled or not.
This might try to reenable already enabled interrupts in the non
failure case, but the only affected platform is XEN and it has been
confirmed that it does not cause any side effects.
[ tglx: Massaged changelog. ]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Acked-by-and-tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Pavel Machek <pavel@ucw.cz> Cc: <ian.campbell@citrix.com> Cc: <rjw@rjwysocki.net> Cc: <len.brown@intel.com> Cc: <gregkh@linuxfoundation.org> Link: http://lkml.kernel.org/r/1385388587-16442-1-git-send-email-ldewangan@nvidia.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes the issue that the sja1000_interrupt() function may have
returned IRQ_NONE without processing the optional pre_irq() and post_irq()
function before. Further the irq processing counter 'n' is moved to the end of
the while statement to return correct IRQ_[NONE|HANDLED] values at error
conditions.
Reported-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[bwh: Backported to 3.2: s/SJA1000_IER/REG_IER/; s/SJA1000_IR/REG_IR/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As suggested by Minchan Kim and Jerome Marchand "The code in reset_store
get the block device (bdget_disk()) but it does not put it (bdput()) when
it's done using it. The usage count is therefore incremented but never
decremented."
This patch also puts bdput() for all error cases.
Acked-by: Minchan Kim <minchan@kernel.org> Acked-by: Jerome Marchand <jmarchan@redhat.com> Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch fixes the bug in reset_store caused by accessing NULL pointer.
The bdev gets its value from bdget_disk() which could fail when memory
pressure is severe and hence can return NULL because allocation of
inode in bdget could fail.
Hence, this patch introduces a check for bdev to prevent reference to a
NULL pointer in the later part of the code. It also removes unnecessary
check of bdev for fsync_bdev().
Acked-by: Jerome Marchand <jmarchan@redhat.com> Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com> Acked-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The dwc3 UDC driver doesn't implement endpoint wedging correctly.
When an endpoint is wedged, the gadget driver should be allowed to
clear the wedge by calling usb_ep_clear_halt(). Only the host is
prevented from resetting the endpoint.
This patch fixes the implementation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The delayed_status value is used to keep track of status response
packets on ep0. It needs to be reset or the set_config function would
still delay the answer, if the usb device got unplugged while waiting
for setup_continue to be called.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fix race in generic write implementation, which could lead to
temporarily degraded throughput.
The current generic write implementation introduced by commit 27c7acf22047 ("USB: serial: reimplement generic fifo-based writes") has
always had this bug, although it's fairly hard to trigger and the
consequences are not likely to be noticed.
Specifically, a write() on one CPU while the completion handler is
running on another could result in only one of the two write urbs being
utilised to empty the remainder of the write fifo (unless there is a
second write() that doesn't race during that time).
Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: deleted code is a bit different] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Multicast frames can't be transmitted as part of an aggregation
session (such a session couldn't even be set up) so don't try to
reorder them. Trying to do so would cause the reorder to stop
working correctly since multicast QoS frames (as transmitted by
the Aruba APs this was found with) would cause sequence number
confusion in the buffer.
Reported-by: Blaise Gassend <blaise@suitabletech.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In a recent patch:
commit c13f20ac48328b05cd3b8c19e31ed6c132b44b42
Author: Michael Neuling <mikey@neuling.org>
powerpc/signals: Mark VSX not saved with small contexts
We fixed an issue but an improved solution was later discussed after the patch
was merged.
Firstly, this patch doesn't handle the 64bit signals case, which could also hit
this issue (but has never been reported).
Secondly, the original patch isn't clear what MSR VSX should be set to. The
new approach below always clears the MSR VSX bit (to indicate no VSX is in the
context) and sets it only in the specific case where VSX is available (ie. when
VSX has been used and the signal context passed has space to provide the
state).
This reverts the original patch and replaces it with the improved solution. It
also adds a 64 bit version.
Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>