'dspi_request_dma()' should be undone by a 'dspi_release_dma()' call in the
error handling path of the probe function, as already done in the remove
function
Fixes: 90ba37033cb9 ("spi: spi-fsl-dspi: Add DMA support for Vybrid") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/d51caaac747277a1099ba8dea07acd85435b857e.1620587472.git.christophe.jaillet@wanadoo.fr Signed-off-by: Mark Brown <broonie@kernel.org>
[sudip: adjust context] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early check if we should attempt compression does not take into
account the number of input pages. It can happen that there's only one
page, eg. a tail page after some ranges of the BTRFS_MAX_UNCOMPRESSED
have been processed, or an isolated page that won't be converted to an
inline extent.
The single page would be compressed but a later check would drop it
again because the result size must be at least one block shorter than
the input. That can never work with just one page.
According to the BMA253 datasheet [1] and BMA250 datasheet [2] the
bandwidth value for BMA25x should be set as 01xxx:
"Settings 00xxx result in a bandwidth of 7.81 Hz; [...]
It is recommended [...] to use the range from ´01000b´ to ´01111b´
only in order to be compatible with future products."
However, at the moment the drivers sets bandwidth values from 0 to 6,
which is not recommended and always results into 7.81 Hz bandwidth
according to the datasheet.
Fix this by introducing a bw_offset = 8 = 01000b for BMA25x,
so the additional bit is always set for BMA25x.
This uses the C99 explicit .member assignment for the
variant data in struct bma180_part_info. This makes it
easier to understand and add new variants.
Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.
Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This test passes pointers obtained from anon_allocate_area to the
userfaultfd and mremap APIs. This causes a problem if the system
allocator returns tagged pointers because with the tagged address ABI
the kernel rejects tagged addresses passed to these APIs, which would
end up causing the test to fail. To make this test compatible with such
system allocators, stop using the system allocator to allocate memory in
anon_allocate_area, and instead just use mmap.
When receiving a packet with multiple fragments, hardware may still
touch the first fragment until the entire packet has been received. The
driver therefore keeps the first fragment mapped for DMA until end of
packet has been asserted, and delays its dma_sync call until then.
The driver tries to fit multiple receive buffers on one page. When using
3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned
off/build_skb is being used) on an architecture with 4K pages, the
driver allocates an order 1 compound page and uses one page per receive
buffer. To determine the correct offset for a delayed DMA sync of the
first fragment of a multi-fragment packet, the driver then cannot just
use PAGE_MASK on the DMA address but has to construct a mask based on
the actual size of the backing page.
Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration
will always sync the first page of a compound page. With the SWIOTLB
enabled this can lead to corrupted packets (zeroed out first fragment,
re-used garbage from another packet) and various consequences, such as
slow/stalling data transfers and connection resets. For example, testing
on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled
(e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle
out without this patch.
Cc: stable@vger.kernel.org Fixes: 0c5661ecc5dd7 ("ixgbe: fix crash in build_skb Rx code path") Signed-off-by: Markus Boehme <markubo@amazon.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix an 11-year old bug in ngene_command_config_free_buf() while
addressing the following warnings caught with -Warray-bounds:
arch/alpha/include/asm/string.h:22:16: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [12, 16] from the object at 'com' is out of the bounds of referenced subobject 'config' with type 'unsigned char' at offset 10 [-Warray-bounds]
The problem is that the original code is trying to copy 6 bytes of
data into a one-byte size member _config_ of the wrong structue
FW_CONFIGURE_BUFFERS, in a single call to memcpy(). This causes a
legitimate compiler warning because memcpy() overruns the length
of &com.cmd.ConfigureBuffers.config. It seems that the right
structure is FW_CONFIGURE_FREE_BUFFERS, instead, because it contains
6 more members apart from the header _hdr_. Also, the name of
the function ngene_command_config_free_buf() suggests that the actual
intention is to ConfigureFreeBuffers, instead of ConfigureBuffers
(which takes place in the function ngene_command_config_buf(), above).
Fix this by enclosing those 6 members of struct FW_CONFIGURE_FREE_BUFFERS
into new struct config, and use &com.cmd.ConfigureFreeBuffers.config as
the destination address, instead of &com.cmd.ConfigureBuffers.config,
when calling memcpy().
This also helps with the ongoing efforts to globally enable
-Warray-bounds and get us closer to being able to tighten the
FORTIFY_SOURCE routines on memcpy().
The "rb_per_cpu_empty()" misinterpret the condition (as not-empty) when
"head_page" and "commit_page" of "struct ring_buffer_per_cpu" points to
the same buffer page, whose "buffer_data_page" is empty and "read" field
is non-zero.
An error scenario could be constructed as followed (kernel perspective):
1. All pages in the buffer has been accessed by reader(s) so that all of
them will have non-zero "read" field.
2. Read and clear all buffer pages so that "rb_num_of_entries()" will
return 0 rendering there's no more data to read. It is also required
that the "read_page", "commit_page" and "tail_page" points to the same
page, while "head_page" is the next page of them.
3. Invoke "ring_buffer_lock_reserve()" with large enough "length"
so that it shot pass the end of current tail buffer page. Now the
"head_page", "commit_page" and "tail_page" points to the same page.
4. Discard current event with "ring_buffer_discard_commit()", so that
"head_page", "commit_page" and "tail_page" points to a page whose buffer
data page is now empty.
When the error scenario has been constructed, "tracing_read_pipe" will
be trapped inside a deadloop: "trace_empty()" returns 0 since
"rb_per_cpu_empty()" returns 0 when it hits the CPU containing such
constructed ring buffer. Then "trace_find_next_entry_inc()" always
return NULL since "rb_num_of_entries()" reports there's no more entry
to read. Finally "trace_seq_to_user()" returns "-EBUSY" spanking
"tracing_read_pipe" back to the start of the "waitagain" loop.
I've also written a proof-of-concept script to construct the scenario
and trigger the bug automatically, you can use it to trace and validate
my reasoning above:
Tests has been carried out on linux kernel 5.14-rc2
(2734d6c1b1a089fb593ef6a23d4b70903526fe0c), my fixed version
of kernel (for testing whether my update fixes the bug) and
some older kernels (for range of affected kernels). Test result is
also attached to the proof-of-concept repository.
Fix comments for GE CS1000 CP210x USB ID assignments.
Fixes: 42213a0190b5 ("USB: serial: cp210x: add some more GE USB IDs") Signed-off-by: Ian Ray <ian.ray@ge.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch is meant to support LARA-R6 Cat 1 module family.
Module USB ID:
Vendor ID: 0x05c6
Product ID: 0x90fA
Interface layout:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: QMI wwan (not available in all versions)
Signed-off-by: Marco De Marco <marco.demarco@posteo.net> Link: https://lore.kernel.org/r/49260184.kfMIbaSn9k@mars Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has a potential issue which this driver is possible to
cause superfluous irqs after usb_pkt_pop() is called. So, after
the commit 3af32605289e ("usb: renesas_usbhs: fix error return
code of usbhsf_pkt_handler()") had been applied, we could observe
the following error happened when we used g_audio.
The MAX-3421 USB driver remembers the state of the USB toggles for a
device/endpoint. To save SPI writes, this was only done when a new
device/endpoint was being used. Unfortunately, if the old device was
removed, this would cause writes to freed memory.
To fix this, a simpler scheme is used. The toggles are read from
hardware when a URB is completed, and the toggles are always written to
hardware when any URB transaction is started. This will cause a few more
SPI transactions, but no causes kernel panics.
Fixes: 2d53139f3162 ("Add support for using a MAX3421E chip as a host driver.") Cc: stable <stable@vger.kernel.org> Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz> Link: https://lore.kernel.org/r/20210625031456.8632-1-mark.tomlinson@alliedtelesis.co.nz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device initiated link power management U1/U2 states should not be
enabled in case the system exit latency plus one bus interval (125us) is
greater than the shortest service interval of any periodic endpoint.
This is the case for both U1 and U2 sytstem exit latencies and link states.
See USB 3.2 section 9.4.9 "Set Feature" for more details
Note, before this patch the host and device initiated U1/U2 lpm states
were both enabled with lpm. After this patch it's possible to end up with
only host inititated U1/U2 lpm in case the exit latencies won't allow
device initiated lpm.
If this case we still want to set the udev->usb3_lpm_ux_enabled flag so
that sysfs users can see the link may go to U1/U2.
The kvmppc_rtas_hcall() sets the host rtas_args.rets pointer based on
the rtas_args.nargs that was provided by the guest. That guest nargs
value is not range checked, so the guest can cause the host rets pointer
to be pointed outside the args array. The individual rtas function
handlers check the nargs and nrets values to ensure they are correct,
but if they are not, the handlers store a -3 (0xfffffffd) failure
indication in rets[0] which corrupts host memory.
Fix this by testing up front whether the guest supplied nargs and nret
would exceed the array size, and fail the hcall directly without storing
a failure indication to rets[0].
Also expand on a comment about why we kill the guest and try not to
return errors directly if we have a valid rets[0] pointer.
There's a small window where a USB 2 remote wake may be left unhandled
due to a race between hub thread and xhci port event interrupt handler.
When the resume event is detected in the xhci interrupt handler it kicks
the hub timer, which should move the port from resume to U0 once resume
has been signalled for long enough.
To keep the hub "thread" running we set a bus_state->resuming_ports flag.
This flag makes sure hub timer function kicks itself.
checking this flag was not properly protected by the spinlock. Flag was
copied to a local variable before lock was taken. The local variable was
then checked later with spinlock held.
If interrupt is handled right after copying the flag to the local variable
we end up stopping the hub thread before it can handle the USB 2 resume.
CPU0 CPU1
(hub thread) (xhci event handler)
xhci_hub_status_data()
status = bus_state->resuming_ports;
<Interrupt>
handle_port_status()
spin_lock()
bus_state->resuming_ports = 1
set_flag(HCD_FLAG_POLL_RH)
spin_unlock()
spin_lock()
if (!status)
clear_flag(HCD_FLAG_POLL_RH)
spin_unlock()
Fix this by taking the lock a bit earlier so that it covers
the resuming_ports flag copy in the hub thread
SB16 CSP driver may hit potentially a typical ABBA deadlock in two
code paths:
In snd_sb_csp_stop():
spin_lock_irqsave(&p->chip->mixer_lock, flags);
spin_lock(&p->chip->reg_lock);
In snd_sb_csp_load():
spin_lock_irqsave(&p->chip->reg_lock, flags);
spin_lock(&p->chip->mixer_lock);
Also the similar pattern is seen in snd_sb_csp_start().
Although the practical impact is very small (those states aren't
triggered in the same running state and this happens only on a real
hardware, decades old ISA sound boards -- which must be very difficult
to find nowadays), it's a real scenario and has to be fixed.
This patch addresses those deadlocks by splitting the locks in
snd_sb_csp_start() and snd_sb_csp_stop() for avoiding the nested
locks.
s390 enforces DYNAMIC_FTRACE if FUNCTION_TRACER is selected.
At the same time implementation of ftrace_caller is not compliant with
HAVE_DYNAMIC_FTRACE since it doesn't provide implementation of
ftrace_update_ftrace_func() and calls ftrace_trace_function() directly.
The subtle difference is that during ftrace code patching ftrace
replaces function tracer via ftrace_update_ftrace_func() and activates
it back afterwards. Unexpected direct calls to ftrace_trace_function()
during ftrace code patching leads to nullptr-dereferences when tracing
is activated for one of functions which are used during code patching.
Those function currently are:
copy_from_kernel_nofault()
copy_from_kernel_nofault_allowed()
preempt_count_sub() [with debug_defconfig]
preempt_count_add() [with debug_defconfig]
Corresponding KASAN report:
BUG: KASAN: nullptr-dereference in function_trace_call+0x316/0x3b0
Read of size 4 at addr 0000000000001e08 by task migration/0/15
Commit b2b29d6d011944 (mm: account PMD tables like PTE tables) is
introduced between v5.9 and v5.10, so this fix (commit 002d8b395fa1)
should NOT apply to any pre-5.10 branch.
Use size_t when capping the count argument received by mem_rw(). Since
count is size_t, using min_t(int, ...) can lead to a negative value
that will later be passed to access_remote_vm(), which can cause
unexpected behavior.
Since we are capping the value to at maximum PAGE_SIZE, the conversion
from size_t to int when passing it to access_remote_vm() as "len"
shouldn't be a problem.
Link: https://lkml.kernel.org/r/20210512125215.3348316-1-marcelo.cerri@canonical.com Reviewed-by: David Disseldorp <ddiss@suse.de> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by: Marcelo Henrique Cerri <marcelo.cerri@canonical.com> Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Souza Cascardo <cascardo@canonical.com> Cc: Christian Brauner <christian.brauner@ubuntu.com> Cc: Michel Lespinasse <walken@google.com> Cc: Helge Deller <deller@gmx.de> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Lorenzo Stoakes <lstoakes@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the patch was working as stated,ie preventing the L850-GL LTE modem
from crashing on some U3 wake-ups due to a race condition between the
host wake-up and the modem-side wake-up, when using the MBIM interface,
this would force disabling the USB runtime PM on the device.
The increased power consumption is significant for LTE laptops,
and given that with decently recent modem firmwares, when the modem hits
the bug, it automatically recovers (ie it drops from the bus, but
automatically re-enumerates after less than half a second, rather than being
stuck until a power cycle as it was doing with ancient firmware), for
most people, the trade-off now seems in favor of re-enabling it by
default.
For people with access to the platform code, the bug can also be worked-around
successfully by changing the USB3 LFPM polling off-time for the XHCI
controller in the BIOS code.
The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8bf98 ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.
Undo 734882a8bf98 ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.
Fixes: 734882a8bf98 ("spi: cadence: Correct initialisation of runtime PM") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Charles Keepax <ckeepax@opensource.cirrus.com> Cc: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A ISCSI_IFACE_PARAM can have the same value as a ISCSI_NET_PARAM so when
iscsi_iface_attr_is_visible tries to figure out the type by just checking
the value, we can collide and return the wrong type. When we call into the
driver we might not match and return that we don't want attr visible in
sysfs. The patch fixes this by setting the type when we figure out what the
param is.
Link: https://lore.kernel.org/r/20210701002559.89533-1-michael.christie@oracle.com Fixes: 3e0f65b34cc9 ("[SCSI] iscsi_transport: Additional parameters for network settings") Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 63346650c1a9 ("netrom: switch to sock timer API") switched to use
sock timer API. It replaces mod_timer() by sk_reset_timer(), and
del_timer() by sk_stop_timer().
Function sk_reset_timer() will increase the refcount of sock if it is
called on an inactive timer, hence, in case the timer expires, we need to
decrease the refcount ourselves in the handler, otherwise, the sock
refcount will be unbalanced and the sock will never be freed.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com> Reported-by: syzbot+10f1194569953b72f1ae@syzkaller.appspotmail.com Fixes: 63346650c1a9 ("netrom: switch to sock timer API") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The release_sock() is blocking function, it would change the state
after sleeping. use wait_woken() instead.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When nr_segs equal to zero in iovec_from_user, the object
msg->msg_iter.iov is uninit stack memory in caif_seqpkt_sendmsg
which is defined in ___sys_sendmsg. So we cann't just judge
msg->msg_iter.iov->base directlly. We can use nr_segs to judge
msg in caif_seqpkt_sendmsg whether has data buffers.
Currently array jit->seen_reg[r1] is being accessed before the range
checking of index r1. The range changing on r1 should be performed
first since it will avoid any potential out-of-range accesses on the
array seen_reg[] and also it is more optimal to perform checks on r1
before fetching data from the array. Fix this by swapping the order
of the checks before the array access.
Fixes: 054623105728 ("s390/bpf: Add s390x eBPF JIT compiler backend") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Ilya Leoshkevich <iii@linux.ibm.com> Acked-by: Ilya Leoshkevich <iii@linux.ibm.com> Link: https://lore.kernel.org/bpf/20210715125712.24690-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Shifting the u16 integer oct->pcie_port by CN23XX_PKT_INPUT_CTL_MAC_NUM_POS
(29) bits will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the cases where oct->pcie_port where bit 2 is set (e.g. 3..7)
the shifted value will be sign extended and the top 32 bits of the result
will be set.
Fix this by casting the u16 values to a u64 before the 29 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 3451b97cce2d ("liquidio: CN23XX register setup") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In FIFO mode were two problems:
- RX mode was never handled and
- in this case the tx_buf pointer was NULL and caused an exception
fix this by handling RX mode in mtk_spi_fifo_transfer
Fixes: a568231f4632 ("spi: mediatek: Add spi bus for Mediatek MT8173") Signed-off-by: Peter Hess <peter.hess@ph-home.de> Signed-off-by: Frank Wunderlich <frank-w@public-files.de> Link: https://lore.kernel.org/r/20210706121609.680534-1-linux@fw-web.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that the adapter->q_vector[MAX_Q_VECTORS] array isn't accessed
beyond its size. It was fixed by using a local variable num_q_vectors
as a limit for loop index, and ensure that num_q_vectors is not bigger
than MAX_Q_VECTORS.
Fixes: 047e0030f1e6 ("igb: add new data structure for handling interrupts and NAPI") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Reviewed-by: Grzegorz Siwik <grzegorz.siwik@intel.com> Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Reviewed-by: Slawomir Laba <slawomirx.laba@intel.com> Reviewed-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Reviewed-by: Mateusz Palczewski <mateusz.placzewski@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 5eae00c57f5e ("i40evf: main driver core") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 19ae1b3fb99c ("fm10k: Add support for PCI power management and error handling") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Fixes: 40a914fa72ab ("igb: Add support for pci-e Advanced Error Reporting") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.
Cleans the next descriptor to watch (next_to_watch) when cleaning the
TX ring.
Failure to do so can cause invalid memory accesses. If igb_poll() runs
while the controller is reset this can lead to the driver try to free
a skb that was already freed.
(The crash is harder to reproduce with the igb driver, but the same
potential problem exists as the code is identical to igc)
Fixes: 7cc6fd4c60f2 ("igb: Don't bother clearing Tx buffer_info in igb_clean_tx_ring") Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Reported-by: Erez Geva <erez.geva.ext@siemens.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While TCP stack scales reasonably well, there is still one part that
can be used to DDOS it.
IPv6 Packet too big messages have to lookup/insert a new route,
and if abused by attackers, can easily put hosts under high stress,
with many cpus contending on a spinlock while one is stuck in fib6_run_gc()
Some of our servers have been hit by malicious ICMPv6 packets
trying to _increase_ the MTU/MSS of TCP flows.
We believe these ICMPv6 packets are a result of a bug in one ISP stack,
since they were blindly sent back for _every_ (small) packet sent to them.
These packets are for one TCP flow:
09:24:36.266491 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.266509 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316688 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.316704 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
09:24:36.608151 IP6 Addr1 > Victim ICMP6, packet too big, mtu 1460, length 1240
TCP stack can filter some silly requests :
1) MTU below IPV6_MIN_MTU can be filtered early in tcp_v6_err()
2) tcp_v6_mtu_reduced() can drop requests trying to increase current MSS.
This tests happen before the IPv6 routing stack is entered, thus
removing the potential contention and route exhaustion.
Note that IPv6 stack was performing these checks, but too late
(ie : after the route has been added, and after the potential
garbage collect war)
v2: fix typo caught by Martin, thanks !
v3: exports tcp_mtu_to_mss(), caught by David, thanks !
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Maciej Żenczykowski <maze@google.com> Cc: Martin KaFai Lau <kafai@fb.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While tp->mtu_info is read while socket is owned, the write
sides happen from err handlers (tcp_v[46]_mtu_reduced)
which only own the socket spinlock.
Fixes: 563d34d05786 ("tcp: dont drop MTU reduction indications") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each add_fence() call does a dma_fence_get() on the relevant fence. In
the error path, we weren't calling dma_fence_put() so all those fences
got leaked. Also, in the krealloc_array failure case, we weren't
freeing the fences array. Instead, ensure that i and fences are always
zero-initialized and dma_fence_put() all the fences and kfree(fences) on
every error path.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net> Reviewed-by: Christian König <christian.koenig@amd.com> Fixes: a02b9dc90d84 ("dma-buf/sync_file: refactor fence storage in struct sync_file") Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Cc: Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210624174732.1754546-1-jason@jlekstrand.net Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb_tunnel_info() returns pointer of lwtstate->data as ip_tunnel_info
type without validation. lwtstate->data can have various types such as
mpls_iptunnel_encap, etc and these are not compatible.
So skb_tunnel_info() should validate before returning that pointer.
Splat looks like:
BUG: KASAN: slab-out-of-bounds in vxlan_get_route+0x418/0x4b0 [vxlan]
Read of size 2 at addr ffff888106ec2698 by task ping/811
Fixes: 61adedf3e3f1 ("route: move lwtunnel state to dst_entry") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e05a90ec9e16 ("net: reflect mark on tcp syn ack packets")
fixed IPv4 only.
This part is for the IPv6 side.
Fixes: e05a90ec9e16 ("net: reflect mark on tcp syn ack packets") Signed-off-by: Alexander Ovechkin <ovov@yandex-team.ru> Acked-by: Dmitry Yakunin <zeil@yandex-team.ru> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
priv is netdev private data and it cannot be
used after free_netdev() call. Using priv after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 1e0a8b13d355 ("tlan: cancel work at remove path") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
adpt is netdev private data and it cannot be
used after free_netdev() call. Using adpt after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 54e19bc74f33 ("net: qcom/emac: do not use devm on internal phy pdev") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So, there is no need to call free_netdev() before jumping
to error handling path, since it can cause UAF or double-free
bug.
Fixes: 6c821bd9edc9 ("net: Add MOXA ART SoCs ethernet driver") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.
Tested-by: Maxime Ripard <maxime@cerno.tech> Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 2796d0c648c9 ("bridge: Automatically manage
port promiscuous mode.")
bridges with `vlan_filtering 1` and only 1 auto-port don't
set IFF_PROMISC for unicast-filtering-capable ports.
Normally on port changes `br_manage_promisc` is called to
update the promisc flags and unicast filters if necessary,
but it cannot distinguish between *new* ports and ones
losing their promisc flag, and new ports end up not
receiving the MAC address list.
Fix this by calling `br_fdb_sync_static` in `br_add_if`
after the port promisc flags are updated and the unicast
filter was supposed to have been filled.
Fixes: 2796d0c648c9 ("bridge: Automatically manage port promiscuous mode.") Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two patches listed below removed ctnetlink_dump_helpinfo call from under
rcu_read_lock. Now its rcu_dereference generates following warning:
=============================
WARNING: suspicious RCU usage
5.13.0+ #5 Not tainted
-----------------------------
net/netfilter/nf_conntrack_netlink.c:221 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
stack backtrace:
CPU: 1 PID: 2251 Comm: conntrack Not tainted 5.13.0+ #5
Call Trace:
dump_stack+0x7f/0xa1
ctnetlink_dump_helpinfo+0x134/0x150 [nf_conntrack_netlink]
ctnetlink_fill_info+0x2c2/0x390 [nf_conntrack_netlink]
ctnetlink_dump_table+0x13f/0x370 [nf_conntrack_netlink]
netlink_dump+0x10c/0x370
__netlink_dump_start+0x1a7/0x260
ctnetlink_get_conntrack+0x1e5/0x250 [nf_conntrack_netlink]
nfnetlink_rcv_msg+0x613/0x993 [nfnetlink]
netlink_rcv_skb+0x50/0x100
nfnetlink_rcv+0x55/0x120 [nfnetlink]
netlink_unicast+0x181/0x260
netlink_sendmsg+0x23f/0x460
sock_sendmsg+0x5b/0x60
__sys_sendto+0xf1/0x160
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x36/0x70
entry_SYSCALL_64_after_hwframe+0x44/0xae
Commit 628a5c561890 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE") introduced
ip6_skb_dst_mtu with return value of signed int which is inconsistent
with actually returned values. Also 2 users of this function actually
assign its value to unsigned int variable and only __xfrm6_output
assigns result of this function to signed variable but actually uses
as unsigned in further comparisons and calls. Change this function
to return unsigned int value.
Fixes: 628a5c561890 ("[INET]: Add IP(V6)_PMTUDISC_RPOBE") Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The time remaining until expiry of the refresh_timer can be negative.
Casting the type to an unsigned 64-bit value will cause integer
underflow, making the runtime_refresh_within return false instead of
true. These situations are rare, but they do happen.
This does not cause user-facing issues or errors; other than
possibly unthrottling cfs_rq's using runtime from the previous period(s),
making the CFS bandwidth enforcement less strict in those (special)
situations.
Signed-off-by: Odin Ugedal <odin@uged.al> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Ben Segall <bsegall@google.com> Link: https://lore.kernel.org/r/20210629121452.18429-1-odin@uged.al Signed-off-by: Sasha Levin <sashal@kernel.org>
The shifting of the u8 integer returned fom ahc_inb(ahc, port+3) by 24 bits
to the left will be promoted to a 32 bit signed int and then sign-extended
to a u64. In the event that the top bit of the u8 is set then all then all
the upper 32 bits of the u64 end up as also being set because of the
sign-extension. Fix this by casting the u8 values to a u64 before the 24
bit left shift.
[ This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit f58eb66c0b0a ("Update aic7xxx driver to 6.2.10...") ]
Link: https://lore.kernel.org/r/20210621151727.20667-1-colin.king@canonical.com Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Addresses-Coverity: ("Unintended sign extension") Signed-off-by: Sasha Levin <sashal@kernel.org>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77686 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
To avoid unnecessary recompilations, mkcompile_h does not regenerate
compile.h if just the timestamp changed.
Though, if KBUILD_BUILD_TIMESTAMP is set, an explicit timestamp for the
build was requested, in which case we should not ignore it.
If a user follows the documentation for reproducible builds [1] and
defines KBUILD_BUILD_TIMESTAMP as the git commit timestamp, a clean
build will have the correct timestamp. A subsequent cherry-pick (or
amend) changes the commit timestamp and if an incremental build is done
with a different KBUILD_BUILD_TIMESTAMP now, that new value is not taken
into consideration. But it should for reproducibility.
Hence, whenever KBUILD_BUILD_TIMESTAMP is explicitly set, do not ignore
UTS_VERSION when making a decision about whether the regenerated version
of compile.h should be moved into place.
drivers/thermal/thermal_core.c:1376: warning: expecting prototype for thermal_device_unregister(). Prototype was for thermal_zone_device_unregister() instead
On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:
[ 10.471363] couldn't get idr
[ 10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[ 10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[ 10.471708] fsl-dspi: probe of 2100000.spi failed with error -16
Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c33c ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.
Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.
Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.
When a PIM hello packet is received on a bridge port with multicast
snooping enabled, we mark it as a router port automatically, that
includes adding that port the router port list. The multicast lock
protects that list, but it is not acquired in the PIM message case
leading to a race condition, we need to take it to fix the race.
Cc: stable@vger.kernel.org Fixes: 91b02d3d133b ("bridge: mcast: add router port on PIM hello message") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing raw timers (currently only CLOCK_MONOTONIC_RAW) through VDSO
doesn't return the correct time when using the GIC as clock source.
The address of the GIC mapped page is in this case not calculated
correctly. The GIC mapped page is calculated from the VDSO data by
subtracting PAGE_SIZE:
However, the data pointer is not page aligned for raw clock sources.
This is because the VDSO data for raw clock sources (CS_RAW = 1) is
stored after the VDSO data for coarse clock sources (CS_HRES_COARSE = 0).
Therefore, only the VDSO data for CS_HRES_COARSE is page aligned:
When __arch_get_hw_counter() is called with &vd[CS_RAW], get_gic returns
the wrong address (somewhere inside the GIC mapped page). The GIC counter
values are not returned which results in an invalid time.
Fixes: a7f4df4e21dd ("MIPS: VDSO: Add implementations of gettimeofday() and clock_gettime()") Signed-off-by: Martin Fäcknitz <faecknitz@hotsplots.de> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use DISABLE_BRANCH_PROFILING for arch/mips/boot/compressed/decompress.o
to prevent linkage errors.
mips64-linux-ld: arch/mips/boot/compressed/decompress.o: in function `LZ4_decompress_fast_extDict':
decompress.c:(.text+0x8c): undefined reference to `ftrace_likely_update'
mips64-linux-ld: decompress.c:(.text+0xf4): undefined reference to `ftrace_likely_update'
mips64-linux-ld: decompress.c:(.text+0x200): undefined reference to `ftrace_likely_update'
mips64-linux-ld: decompress.c:(.text+0x230): undefined reference to `ftrace_likely_update'
mips64-linux-ld: decompress.c:(.text+0x320): undefined reference to `ftrace_likely_update'
mips64-linux-ld: arch/mips/boot/compressed/decompress.o:decompress.c:(.text+0x3f4): more undefined references to `ftrace_likely_update' follow
Fixes: e76e1fdfa8f8 ("lib: add support for LZ4-compressed kernel") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: linux-mips@vger.kernel.org Cc: Kyungsik Lee <kyungsik.lee@lge.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
My series to clean up the unaligned access implementation
across architectures caused some mips randconfig builds to
fail with:
mips64-linux-ld: arch/mips/boot/compressed/decompress.o: in function `decompress_kernel':
decompress.c:(.text.decompress_kernel+0x54): undefined reference to `__bswapsi2'
It turns out that this problem has already been fixed for the XZ
decompressor but now it also shows up in (at least) LZO and LZ4. From my
analysis I concluded that the compiler could always have emitted those
calls, but the different implementation allowed it to make otherwise
better decisions about not inlining the byteswap, which results in the
link error when the out-of-line code is missing.
While it could be addressed by adding it to the two decompressor
implementations that are known to be affected, but as this only adds
112 bytes to the kernel, the safer choice is to always add them.
If an error occurs after a pci_enable_pcie_error_reporting() call, it must
be undone by a corresponding pci_disable_pcie_error_reporting() call, as
already done in the remove function.
This fixes:
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dt.yaml: spi@18029200: interrupt-names: 'oneOf' conditional failed, one must be fixed:
['spi_lr_fullness_reached', 'spi_lr_session_aborted', 'spi_lr_impatient', 'spi_lr_session_done', 'spi_lr_overhead', 'mspi_done', 'mspi_halted'] is too long
Additional items are not allowed ('spi_lr_session_aborted', 'spi_lr_impatient', 'spi_lr_session_done', 'spi_lr_overhead', 'mspi_done', 'mspi_halted' were unexpected)
'mspi_done' was expected
'spi_l1_intr' was expected
'mspi_halted' was expected
'spi_lr_fullness_reached' was expected
'spi_lr_session_aborted' was expected
'spi_lr_impatient' was expected
'spi_lr_session_done' was expected
'spi_lr_overread' was expected
From schema: Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.yaml
arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dt.yaml: spi-nor@0: $nodename:0: 'spi-nor@0' does not match '^flash(@.*)?$'
From schema: Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
arch/arm/boot/dts/r8a7779-marzen.dt.yaml: display@fff80000: clock-names:0: 'du.0' was expected
Change the first clock name to match the DT bindings.
This has no effect on actual operation, as the Display Unit driver in
Linux does not use the first clock name on R-Car H1, but just grabs the
first clock.
The scnprintf() function silently truncates the printf() and returns
the number bytes that it was able to copy (not counting the NUL
terminator). Thus, the highest value it can return here is
"NAME_SIZE - 1" and the overflow check is dead code. Fix this by
using the snprintf() function which returns the number of bytes that
would have been copied if there was enough space and changing the
condition from "> NAME_SIZE" to ">= NAME_SIZE".
Fixes: 92589c986b33 ("rtc-proc: permit the /proc/driver/rtc device to use other devices") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/YJov/pcGmhLi2pEl@mwanda Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log