According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.
This fixes an issue we saw with DMA transfers.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
commit dd4b487b32a35 ("ARM: dts: imx6: Use correct SDMA script
for SPI cores") is fixing the same issue but only for SPI1 - 4.
When the P4D page table layer is folded at runtime, the p4d_free()
should do nothing, the same as in <asm-generic/pgtable-nop4d.h>.
It seems this bug should cause double-free in efi_call_phys_epilog(),
but I don't know how to trigger that code path, so I can't confirm that
by testing.
Like LibreTech-CC, the USB0 needs the 5V regulator to be enabled to power the
devices on the P212 Reference Design based boards.
Fixes: b9f07cb4f41f ("ARM64: dts: meson-gxl-s905x-p212: enable the USB controller") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This needs to use xt_unregister_targets, else new revision is left
on the list which then causes list to point to a target struct that has been free'd.
Fixes: 472a73e00757 ("netfilter: xt_conntrack: Support bit-shifting for CONNMARK & MARK targets.") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 47b7e7f82802, this bit was removed at the same time the
RT6_LOOKUP_F_IFACE flag was removed. However, it is needed when
link-local addresses are used, which is a very common case: when
packets are routed, neighbor solicitations are done using link-local
addresses. For example, the following neighbor solicitation is not
matched by "-m rpfilter":
IP6 fe80::5254:33ff:fe00:1 > ff02::1:ff00:3: ICMP6, neighbor
solicitation, who has 2001:db8::5254:33ff:fe00:3, length 32
Commit 47b7e7f82802 doesn't quite explain why we shouldn't use
RT6_LOOKUP_F_IFACE in the rpfilter case. I suppose the interface check
later in the function would make it redundant. However, the remaining
of the routing code is using RT6_LOOKUP_F_IFACE when there is no
source address (which matches rpfilter's case with a non-unicast
destination, like with neighbor solicitation).
Signed-off-by: Vincent Bernat <vincent@bernat.im> Fixes: 47b7e7f82802 ("netfilter: don't set F_IFACE on ipv6 fib lookups") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SF and clipper units mishandle the provoking vertex in some cases,
which can cause misrendering with shaders that use flat shaded inputs.
There are chicken bits in 3D_CHICKEN3 (for SF) and FF_SLICE_CHICKEN
(for the clipper) that work around the issue. These registers are
unfortunately not part of the logical context (even the power context),
and so we must reload them every time we start executing in a context.
While Bspec doesn't list a specific sequence for turning off the DP port
on g4x we are getting an underrun if the port is disabled in the
.disable() hook. Looks like the pipe stops when the port stops, and by
that time the plane disable may not have completed yet. Also the plane(s)
seem to end up in some wonky state when this happens as they also signal
another underrun immediately after we turn them back on during the next
enable sequence.
We could add a vblank wait in .disable() to avoid wedging the planes,
but I assume we're still tripping up the pipe in some way. So it seems
better to me to just follow the ILK+ sequence and turn off the DP port
in .post_disable() instead. This sequence doesn't seem to suffer from
this problem. Could be it was always the intended sequence for DP and
the gen4 bspec was just never updated to include it.
Originally we used the bad sequence even on ilk+, but I changed that
in commit 08aff3fe26ae ("drm/i915: Move DP port disable to post_disable
for pch platforms") as it was causing issues on those platforms as well.
I left out g4x then only because I didn't have the hardware to test it.
Now that I do it's fairly clear that the ilk+ sequence is also the
right choice for g4x.
v2: Fix whitespace fail (Jani)
Mention the ilk+ commit (Jani)
Looks like interlaced DP output doesn't work on g4x either. Not all
that surprising considering we already established that interlaced
DP output is busted on VLV/CHV.
On i965/g4x IIR is edge triggered. So in order for IIR to notice that
there is still a pending interrupt we have to force and edge in ISR.
For the ISR/IIR pipe event bits we can do that by temporarily
clearing all the PIPESTAT enable bits when we ack the status bits.
This will force the ISR pipe event bit low, and it can then go back
high when we restore the PIPESTAT enable bits.
This avoids the following race:
1. stat = read(PIPESTAT)
2. an enabled PIPESTAT status bit goes high
3. write(PIPESTAT, enable|stat);
4. write(IIR, PIPE_EVENT)
The end result is IIR==0 and ISR!=0. This can lead to nasty
vblank wait/flip_done timeouts if another interrupt source
doesn't trick us into looking at the PIPESTAT status bits despite
the IIR PIPE_EVENT bit being low.
Before i965 IIR was level triggered so this problem can't actually
happen there. And curiously VLV/CHV went back to the level triggered
scheme as well. But for simplicity we'll use the same i965/g4x
compatible code for all platforms.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106033
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105225
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106030 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180611200258.27121-1-ville.syrjala@linux.intel.com Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 132c27c97cb958f637dc05adc35a61b47779bcd8) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When encountering a connector with the scaling mode property both
intel and modesetting ddxs sometimes add tons of DBLSCAN modes
to the output's mode list. The idea presumably being that since the
output will be going through the panel fitter anyway we can pretend
to use any kind of mode.
Sadly that means we can't reject user modes with the DBLSCAN flag
until we know whether we're going to be using the panel's native
mode or the user mode directly. Doing otherwise means X clients using
xf86vidmode/xrandr will get a protocol error (and often self
terminate as a result) when the kernel refuses to use the requested
mode with the DBLSCAN flag.
To undo the regression we'll move the DBLSCAN checks into the
connector->mode_valid() and encoder->compute_config() hooks.
Cc: stable@vger.kernel.org Cc: Vito Caputo <vcaputo@pengaru.com> Reported-by: Vito Caputo <vcaputo@pengaru.com> Fixes: e995ca0b8139 ("drm/i915: Provide a device level .mode_valid() hook")
References: https://lkml.org/lkml/2018/5/21/715 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180524125403.23445-1-ville.syrjala@linux.intel.com Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106804 Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
(cherry picked from commit e4dd27aadd205417a2e9ea9902b698a0252ec3a0) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, amdgpu_do_flip() spinlocks crtc->dev->event_lock and
releases it only after committing updates to the stream.
dc_commit_updates_for_stream() should be moved out of
spinlock for the below reasons:
1. event_lock is supposed to protect access to acrct->pflip_status _only_
2. dc_commit_updates_for_stream() has potential sleep's
and also its not appropriate to be in an atomic state
for such long sequences of code.
Signed-off-by: Shirish S <shirish.s@amd.com> Suggested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a regression I accidentally reduced that was picked up by
kasan, where we were checking the CRTC atomic states after DRM's helpers
had already freed them. Example:
==================================================================
BUG: KASAN: use-after-free in amdgpu_dm_atomic_commit_tail.cold.50+0x13d/0x15a [amdgpu]
Read of size 1 at addr ffff8803a697b071 by task kworker/u16:0/7
Memory state around the buggy address: ffff8803a697af00: fb fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8803a697af80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff8803a697b000: fc fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb
^ ffff8803a697b080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8803a697b100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
So, we fix this by counting the number of CRTCs this atomic commit disabled
early on in the function before their atomic states have been freed, then use
that count later to do the appropriate number of RPM puts at the end of the
function.
Acked-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Cc: stable@vger.kernel.org Fixes: 97028037a38ae ("drm/amdgpu: Grab/put runtime PM references in atomic_commit_tail()") Signed-off-by: Lyude Paul <lyude@redhat.com> Cc: Michel Dänzer <michel@daenzer.net> Reported-by: Michel Dänzer <michel@daenzer.net> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
start / last / max_entries are numbers of GPU pages, pfn / count are
numbers of CPU pages. Convert between them accordingly.
Fixes badness on systems with > 4K page size.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/106258 Reported-by: Matt Corallo <freedesktop@bluematt.me> Tested-by: foxbat@ruin.net Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least in theory, ttm_bo_validate may move the BO, in which case the
pin_size accounting would be inconsistent with when the BO was pinned.
Cc: stable@vger.kernel.org Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even BOs with AMDGPU_GEM_CREATE_NO_CPU_ACCESS may end up at least
partially in CPU visible VRAM, in particular when all VRAM is visible.
v2:
* Don't take VRAM mgr spinlock, not needed (Christian König)
* Make loop logic simpler and clearer.
Cc: stable@vger.kernel.org Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preparation for the following fix, no functional change intended.
Cc: stable@vger.kernel.org Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can be quite big, and there's no need for it to be physically
contiguous. This is less likely to fail under memory pressure (has
actually happened while running piglit).
Cc: stable@vger.kernel.org Signed-off-by: Michel Dänzer <michel.daenzer@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've had a number of users report failures to detect and light up
display with DC with LVDS and VGA. These connector types are not
currently supported with DC. I'd like to add support but unfortunately
don't have a system with LVDS or VGA available.
In order not to cause regressions we should probably fallback to the
non-DC driver for ASICs that support VGA and LVDS.
The offending commit triggers a run-time fault when accessing the panel
element of the sun4i_tcon structure when no such panel is attached.
It was apparently assumed in said commit that a panel is always used with
the TCON. Although it is often the case, this is not always true.
For instance a bridge might be used instead of a panel.
This issue was discovered using an A13-OLinuXino, that uses the TCON
in RGB mode for a simple DAC-based VGA bridge.
The statement always evaluates to true since the struct fields
are arrays. This has shown up as a warning when compiling with
clang:
warning: address of array 'desc->layout.xstride' will always
evaluate to 'true' [-Wpointer-bool-conversion]
"qxl_bo_unref" may sleep, but calling "qxl_release_map" causes
"preempt_disable()" to be called and "preempt_enable()" isn't called
until "qxl_release_unmap" is used. Move the call to "qxl_bo_unref" out
from in between the two to avoid sleeping from an atomic context.
This issue can be demonstrated on a kernel with CONFIG_LOCKDEP=y by
creating a VM using QXL, using a desktop environment using Xorg, then
moving the cursor on or off a window.
When doing a modeset where the sink is transitioning from D3 to D0 , it
would sometimes be possible for the initial power_up_phy() to start
timing out. This would only be observed in the last action before the
sink went into D3 mode was intel_dp_sink_dpms(DRM_MODE_DPMS_OFF). We
originally thought this might be an issue with us accidentally shutting
off the aux block when putting the sink into D3, but since the DP spec
mandates that sinks must wake up within 1ms while we have 100ms to
respond to an ESI irq, this didn't really add up. Turns out that the
problem is more subtle then that:
It turns out that the timeout is from us not enabling DPMS on the MST
hub before actually trying to initiate sideband communications. This
would cause the first sideband communication (power_up_phy()), to start
timing out because the sink wasn't ready to respond. Afterwards, we
would call intel_dp_sink_dpms(DRM_MODE_DPMS_ON) in
intel_ddi_pre_enable_dp(), which would actually result in waking up the
sink so that sideband requests would work again.
Since DPMS is what lets us actually bring the hub up into a state where
sideband communications become functional again, we just need to make
sure to enable DPMS on the display before attempting to perform sideband
communications.
Changes since v1:
- Remove comment above if (!intel_dp->is_mst) - vsryjala
- Move intel_dp_sink_dpms() for MST into intel_dp_post_disable_mst() to
keep enable/disable paths symmetrical
- Improve commit message - dhnkrn
Changes since v2:
- Only send DPMS off when we're disabling the last sink, and only send
DPMS on when we're enabling the first sink - dhnkrn
Changes since v3:
- Check against is_mst, not intel_dp->is_mst - dhnkrn/vsyrjala
Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Laura Abbott <labbott@redhat.com> Cc: stable@vger.kernel.org Fixes: ad260ab32a4d9 ("drm/i915/dp: Write to SET_POWER dpcd to enable MST hub.") Link: https://patchwork.freedesktop.org/patch/msgid/20180407011053.22437-1-lyude@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cc6b741c6f63 ("drm: sti: remove useless fields from vtg
structure") reworked some code inside of this driver and made it select
CONFIG_OF. This results in the entire OF layer being enabled when
building an allmodconfig on ia64. OF on ia64 is completely unsupported
so this isn't a great state of affairs.
The 0day robot noticed a link-time failure on ia64 caused by
using of_node_to_nid() in an otherwise unrelated driver. The
generic fallback for of_node_to_nid() only exists when:
Since CONFIG_NUMA is usually selected for IA64 we get the link failure.
Fix this by making the driver depend on OF rather than selecting it,
odds are that was the original intent.
Link: https://lists.01.org/pipermail/kbuild-all/2018-March/045172.html Fixes: cc6b741c6f63 ("drm: sti: remove useless fields from vtg structure") Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org> Cc: Vincent Abriou <vincent.abriou@st.com> Cc: David Airlie <airlied@linux.ie> Cc: dri-devel@lists.freedesktop.org Cc: linux-ia64@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org> Signed-off-by: Philippe Cornu <philippe.cornu@st.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180403053401.30045-1-oohall@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So, unfortunately I recently made the discovery that in the upstream
kernel, the only reason that amdgpu is not currently suffering from
issues with runtime PM putting the GPU into suspend while it's driving
displays is due to the fact that on most prime systems, we have sound
devices associated with the GPU that hold their own runtime PM ref for
the GPU.
What this means however, is that in the event that there isn't any kind
of sound device active (which can easily be reproduced by building a
kernel with sound drivers disabled), the GPU will fall asleep even when
there's displays active. This appears to be in part due to the fact that
amdgpu has not actually ever relied on it's rpm_idle() function to be
the only thing keeping it running, and normally grabs it's own power
references whenever there are displays active (as can be seen with the
original pre-DC codepath in amdgpu_display_crtc_set_config() in
amdgpu_display.c). This means it's very likely that this bug was
introduced during the switch over the DC.
So to fix this, we start grabbing runtime PM references every time we
enable a previously disabled CRTC in atomic_commit_tail(). This appears
to be the correct solution, as it matches up with what i915 does in
i915/intel_runtime_pm.c.
The one sideaffect of this is that we ignore the variable that the
pre-DC code used to use for tracking when it needed runtime PM refs,
adev->have_disp_power_ref. This is mainly because there's no way for a
driver to tell whether or not all of it's CRTCs are enabled or disabled
when we've begun committing an atomic state, as there may be CRTC
commits happening in parallel that aren't contained within the atomic
state being committed. So, it's safer to just get/put a reference for
each CRTC being enabled or disabled in the new atomic state.
Signed-off-by: Lyude Paul <lyude@redhat.com> Acked-by: Christian König <christian.koenig@amd.com>. Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. fix set vce clocks failed on Cz/St
which lead 1s delay when boot up.
2. remove the workaround in vce_v3_0.c
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Shirish S <shirish.s@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fix the issue set uvd clock failed on CZ/ST
which lead 1s delay when boot up.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Huang Rui <ray.huang@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Acked-by: Shirish S <shirish.s@amd.com> Signed-off-by: Rex Zhu <Rex.Zhu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to free all resources associated with the ida on module
exit.
Fixes: cd6484e1830b ("serdev: Introduce new bus for serial attached devices") Cc: stable <stable@vger.kernel.org> # 4.11 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
7d8905d06405 ("serial: 8250_pci: Enable device after we check black list")
pure serial multi-port cards, such as CH355, got blacklisted and thus
not being enumerated anymore. Previously, it seems, blacklisting them
was on purpose to shut up pciserial_init_one() about record duplication.
So, remove the entries from blacklist in order to get cards enumerated.
Fixes: 7d8905d06405 ("serial: 8250_pci: Enable device after we check black list") Reported-by: Matt Turner <mattst88@gmail.com> Cc: Sergej Pupykin <ml@sergej.pp.ru> Cc: Alexandr Petrenko <petrenkoas83@gmail.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupts are ignored if no event bit is set in the status status
register and this breaks the buffer interface. No data is shown when
running "iio_generic_buffer -n mma8451 -a" and interrupt counts go
crazy.
Fix by not returning IRQ_NONE if DRDY is set.
Fixes: 605f72de137a ("iio: accel: mma8452: improvements to handle
multiple events")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The expected return value from ion_map_kernel is an ERR_PTR. The error
path for a vmalloc failure currently just returns NULL, triggering
a warning in ion_buffer_kmap_get. Encode the vmalloc failure as an ERR_PTR.
syzbot is reporting stalls at __process_echoes() [1]. This is because
since ldata->echo_commit < ldata->echo_tail becomes true for some reason,
the discard loop is serving as almost infinite loop. This patch tries to
avoid falling into ldata->echo_commit < ldata->echo_tail situation by
making access to echo_* variables more carefully.
Since reset_buffer_flags() is called without output_lock held, it should
not touch echo_* variables. And omit a call to reset_buffer_flags() from
n_tty_open() by using vzalloc().
Since add_echo_byte() is called without output_lock held, it needs memory
barrier between storing into echo_buf[] and incrementing echo_head counter.
echo_buf() needs corresponding memory barrier before reading echo_buf[].
Lack of handling the possibility of not-yet-stored multi-byte operation
might be the reason of falling into ldata->echo_commit < ldata->echo_tail
situation, for if I do WARN_ON(ldata->echo_commit == tail + 1) prior to
echo_buf(ldata, tail + 1), the WARN_ON() fires.
Also, explicitly masking with buffer for the former "while" loop, and
use ldata->echo_commit > tail for the latter "while" loop.
syzbot is reporting stalls at n_tty_receive_char_special() [1]. This is
because comparison is not working as expected since ldata->read_head can
change at any moment. Mitigate this by explicitly masking with buffer size
when checking condition for "while" loops.
commit 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device")
set dev->udev pointer to NULL in xhci_free_dev(), it will cause kernel
panic in trace_xhci_free_virt_device. This patch reimplement the trace
function trace_xhci_free_virt_device, remove dev->udev dereference and
added more useful parameters to show in the trace function,it also makes
sure dev->udev is not NULL before calling trace_xhci_free_virt_device.
This issue happened when xhci-hcd trace is enabled and USB devices hot
plug test. Original use-after-free patch went to stable so this needs so
be applied there as well.
According to UCSI Specification, Connector Change Event only
means a change in the Connector Status and Operation Mode
fields of the STATUS data structure. So any other change
should create another event.
Unfortunately on some platforms the firmware acting as PPM
(platform policy manager - usually embedded controller
firmware) still does not report any other status changes if
there is a connector change event. So if the connector power
or data role was changed when a device was plugged to the
connector, the driver does not get any indication about
that. The port will show wrong roles if that happens.
To fix the issue, always checking the data and power role
together with a connector change event.
Fixes: c1b0bc2dabfa ("usb: typec: Add support for UCSI interface") Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an issue where the driver fails with an error:
ioremap error for 0x3f799000-0x3f79a000, requested 0x2, got 0x0
On some platforms the UCSI ACPI mailbox SystemMemory
Operation Region may be setup before the driver has been
loaded. That will lead into the driver failing to map the
mailbox region, as it has been already marked as write-back
memory. acpi_os_ioremap() for x86 uses ioremap_cache()
unconditionally.
When the issue happens, the embedded controller has a
pending query event for the UCSI notification right after
boot-up which causes the operation region to be setup before
UCSI driver has been loaded.
The fix is to notify acpi core that the driver is about to
access memory region which potentially overlaps with an
operation region right before mapping it.
acpi_release_memory() will check if the memory has already
been setup (mapped) by acpi core, and deactivate it (unmap)
if it has. The driver is then able to map the memory with
ioremap_nocache() and set the memtype to uncached for the
region.
Sometimes memory resource may be overlapping with
SystemMemory Operation Region by design, for example if the
memory region is used as a mailbox for communication with a
firmware in the system. One occasion of such mailboxes is
USB Type-C Connector System Software Interface (UCSI).
With regions like that, it is important that the driver is
able to map the memory with the requirements it has. For
example, the driver should be allowed to map the memory as
non-cached memory. However, if the operation region has been
accessed before the driver has mapped the memory, the memory
has been marked as write-back by the time the driver is
loaded. That means the driver will fail to map the memory
if it expects non-cached memory.
To work around the problem, introducing helper that the
drivers can use to temporarily deactivate (unmap)
SystemMemory Operation Regions that overlap with their
IO memory.
Fixes: 8243edf44152 ("usb: typec: ucsi: Add ACPI driver") Cc: stable@vger.kernel.org Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The port->logbuffer_head may be wrong if the two processes enters
_tcpm_log at the mostly same time. The 2nd process enters _tcpm_log
before the 1st process update the index, then the 2nd process will
not allocate logbuffer, when the 2nd process tries to use log buffer,
the index has already updated by the 1st process, so it will get
NULL pointer for updated logbuffer, the error message like below:
tcpci 0-0050: Log buffer index 6 is NULL
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jun Li <jun.li@nxp.com> Signed-off-by: Peter Chen <peter.chen@nxp.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: stable <stable@vger.kernel.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2_get_ls_map() use ttport to reference into the
bitmap if we're on a multi_tt hub. But the bitmaps index
from 0 to (hub->maxchild - 1), while the ttport index from
1 to hub->maxchild. This will cause invalid memory access
when the number of ttport is hub->maxchild.
Without this patch, I can easily meet a Kernel panic issue
if connect a low-speed USB mouse with the max port of FE2.1
multi-tt hub (1a40:0201) on rk3288 platform.
Fixes: 9f9f09b048f5 ("usb: dwc2: host: Totally redo the microframe scheduler") Cc: <stable@vger.kernel.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Acked-by: Minas Harutyunyan hminas@synopsys.com> Signed-off-by: William Wu <william.wu@rock-chips.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silicon Labs defines alternative VID/PID pairs for some chips that when
used will automatically install drivers for Windows users without manual
intervention. Unfortunately, these IDs are not recognized by the Linux
module, so using these IDs improves user experience on one platform but
degrades it on Linux. This patch addresses this problem.
Uniden UBC125 radio scanner has USB interface which fails to work
with cdc_acm driver:
usb 1-1.5: new full-speed USB device number 4 using xhci_hcd
cdc_acm 1-1.5:1.0: Zero length descriptor references
cdc_acm: probe of 1-1.5:1.0 failed with error -22
Adding the NO_UNION_NORMAL quirk for the device fixes the issue:
usb 1-4: new full-speed USB device number 15 using xhci_hcd
usb 1-4: New USB device found, idVendor=1965, idProduct=0018
usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-4: Product: UBC125XLT
usb 1-4: Manufacturer: Uniden Corp.
usb 1-4: SerialNumber: 0001
cdc_acm 1-4:1.0: ttyACM0: USB ACM device
`lsusb -v` of the device:
Bus 001 Device 015: ID 1965:0018 Uniden Corporation
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1965 Uniden Corporation
idProduct 0x0018
bcdDevice 0.01
iManufacturer 1 Uniden Corp.
iProduct 2 UBC125XLT
iSerial 3 0001
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 48
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0 None
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x87 EP 7 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 10
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
In vbg_misc_device_ioctl(), the header of the ioctl argument is copied from
the userspace pointer 'arg' and saved to the kernel object 'hdr'. Then the
'version', 'size_in', and 'size_out' fields of 'hdr' are verified.
Before this commit, after the checks a buffer for the entire request would
be allocated and then all data including the verified header would be
copied from the userspace 'arg' pointer again.
Given that the 'arg' pointer resides in userspace, a malicious userspace
process can race to change the data pointed to by 'arg' between the two
copies. By doing so, the user can bypass the verifications on the ioctl
argument.
This commit fixes this by using the already checked copy of the header
to fill the header part of the allocated buffer and only copying the
remainder of the data from userspace.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Cc: Justin Forbes <jmforbes@linuxtx.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Discards issued to a DM thin device can complete to userspace (via
fstrim) _before_ the metadata changes associated with the discards is
reflected in the thinp superblock (e.g. free blocks). As such, if a
user constructs a test that loops repeatedly over these steps, block
allocation can fail due to discards not having completed yet:
1) fill thin device via filesystem file
2) remove file
3) fstrim
From initial report, here:
https://www.redhat.com/archives/dm-devel/2018-April/msg00022.html
"The root cause of this issue is that dm-thin will first remove
mapping and increase corresponding blocks' reference count to prevent
them from being reused before DISCARD bios get processed by the
underlying layers. However. increasing blocks' reference count could
also increase the nr_allocated_this_transaction in struct sm_disk
which makes smd->old_ll.nr_allocated +
smd->nr_allocated_this_transaction bigger than smd->old_ll.nr_blocks.
In this case, alloc_data_block() will never commit metadata to reset
the begin pointer of struct sm_disk, because sm_disk_get_nr_free()
always return an underflow value."
While there is room for improvement to the space-map accounting that
thinp is making use of: the reality is this test is inherently racey and
will result in the previous iteration's fstrim's discard(s) completing
vs concurrent block allocation, via dd, in the next iteration of the
loop.
No amount of space map accounting improvements will be able to allow
user's to use a block before a discard of that block has completed.
So the best we can really do is allow DM thinp to gracefully handle such
aggressive use of all the pool's data by degrading the pool into
out-of-data-space (OODS) mode. We _should_ get that behaviour already
(if space map accounting didn't falsely cause alloc_data_block() to
believe free space was available).. but short of that we handle the
current reality that dm_pool_alloc_data_block() can return -ENOSPC.
Reported-by: Dennis Yang <dennisyang@qnap.com> Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Open-coded page table entry checks don't work correctly when we fold the
page table level at runtime.
pgd_present() on 4-level paging machine always returns true, but
open-coded version of the check may return false-negative result and
we silently skip the rest of the loop body in efi_call_phys_epilog().
Replace open-coded checks with proper helpers.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Baoquan He <bhe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org # v4.12+ Fixes: 94133e46a0f5 ("x86/efi: Correct EFI identity mapping under 'efi=old_map' when KASLR is enabled") Link: http://lkml.kernel.org/r/20180625120852.18300-1-kirill.shutemov@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8bb2610bc496 ("x86/entry/64/compat: Preserve r8-r11 in int $0x80")
was busted: my original patch had a minor conflict with
some of the nospec changes, but "git apply" is very clever
and silently accepted the patch by making the same changes
to a different function in the same file. There was obviously
a huge offset, but "git apply" for some reason doesn't feel
any need to say so.
Move the changes to the correct function. Now the
test_syscall_vdso_32 selftests passes.
If anyone cares to observe the original problem, try applying the
patch at:
If a user is accessing a file in selinuxfs with a pointer to a userspace
buffer that is backed by e.g. a userfaultfd, the userspace access can
stall indefinitely, which can block fsi->mutex if it is held.
For sel_read_policy(), remove the locking, since this method doesn't seem
to access anything that requires locking.
For sel_read_bool(), move the user access below the locked region.
For sel_write_bool() and sel_commit_bools_write(), move the user access
up above the locked region.
Cc: stable@vger.kernel.org Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Jann Horn <jannh@google.com> Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
[PM: removed an unused variable in sel_read_policy()] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to kernel bisection, this problem became visible due to commit f7f99100d8d9 ("mm: stop zeroing memory during allocation in vmemmap")
which changes how struct pages are initialized.
Memblock layout affects the pfn ranges covered by node/zone. Consider
that we have a VM with 2 NUMA nodes and each node has 4GB memory, and
the default (no memmap= given) memblock layout is like below:
This causes shrinking node 0's pfn range because it is calculated by the
address range of memblock.memory. So some of struct pages in the gap
range are left uninitialized.
We have a function zero_resv_unavail() which does zeroing the struct pages
within the reserved unavailable range (i.e. memblock.memory &&
!memblock.reserved). This patch utilizes it to cover all unavailable
ranges by putting them into memblock.reserved.
Link: http://lkml.kernel.org/r/20180615072947.GB23273@hori1.linux.bs1.fc.nec.co.jp Fixes: f7f99100d8d9 ("mm: stop zeroing memory during allocation in vmemmap") Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Tested-by: Oscar Salvador <osalvador@suse.de> Tested-by: "Herton R. Krzesinski" <herton@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com> Cc: Steven Sistare <steven.sistare@oracle.com> Cc: Daniel Jordan <daniel.m.jordan@oracle.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: f9d03f96b988 ("block: improve handling of the magic discard payload") Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Hannes Reinecke <hare@suse.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A device may have boundary restrictions where the number of sectors
between boundaries exceeds its max transfer size. In this case, we need
to cap the max size to the smaller of the two limits.
Reported-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Tested-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Cc: <stable@vger.kernel.org> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
QUEUE_FLAG_DAX is an indication that a given block device supports
filesystem DAX and should not be set for PMEM namespaces which are in "raw"
mode. These namespaces lack struct page and are prevented from
participating in filesystem DAX as of commit 569d0365f571 ("dax: require
'struct page' by default for filesystem dax").
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com> Suggested-by: Mike Snitzer <snitzer@redhat.com> Fixes: 569d0365f571 ("dax: require 'struct page' by default for filesystem dax") Cc: stable@vger.kernel.org Acked-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Toshi Kani <toshi.kani@hpe.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of bio_clone_bioset() is inefficient if there is no need to clone
the original bio's bio_vec array. Best to use the bio_clone_fast()
variant. Also, just using bio_advance() is only part of what is needed
to properly setup the clone -- it doesn't account for the various
bio_integrity() related work that also needs to be performed (see
bio_split).
Address both of these issues by switching from bio_clone_bioset() to
bio_split().
Fixes: 18a25da8 ("dm: ensure bio submission follows a depth-first tree walk") Cc: stable@vger.kernel.org # 4.15+, requires removal of '&' before md->queue->bio_split Reported-by: Christoph Hellwig <hch@lst.de> Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN depends on having access to some of the accounting that SLUB_DEBUG
does; without it, there are immediate crashes [1]. So, the natural
thing to do is to make KASAN select SLUB_DEBUG.
In kernel 4.17 I removed some code from dm-bufio that did slab cache
merging (commit 21bb13276768: "dm bufio: remove code that merges slab
caches") - both slab and slub support merging caches with identical
attributes, so dm-bufio now just calls kmem_cache_create and relies on
implicit merging.
This uncovered a bug in the slub subsystem - if we delete a cache and
immediatelly create another cache with the same attributes, it fails
because of duplicate filename in /sys/kernel/slab/. The slub subsystem
offloads freeing the cache to a workqueue - and if we create the new
cache before the workqueue runs, it complains because of duplicate
filename in sysfs.
This patch fixes the bug by moving the call of kobject_del from
sysfs_slab_remove_workfn to shutdown_cache. kobject_del must be called
while we hold slab_mutex - so that the sysfs entry is deleted before a
cache with the same attributes could be created.
Running device-mapper-test-suite with:
dmtest run --suite thin-provisioning -n /commit_failure_causes_fallback/
triggered:
Buffer I/O error on dev dm-0, logical block 1572848, async page read
device-mapper: thin: 253:1: metadata operation 'dm_pool_alloc_data_block' failed: error = -5
device-mapper: thin: 253:1: aborting current metadata transaction
sysfs: cannot create duplicate filename '/kernel/slab/:a-0000144'
CPU: 2 PID: 1037 Comm: kworker/u48:1 Not tainted 4.17.0.snitm+ #25
Hardware name: Supermicro SYS-1029P-WTR/X11DDW-L, BIOS 2.0a 12/06/2017
Workqueue: dm-thin do_worker [dm_thin_pool]
Call Trace:
dump_stack+0x5a/0x73
sysfs_warn_dup+0x58/0x70
sysfs_create_dir_ns+0x77/0x80
kobject_add_internal+0xba/0x2e0
kobject_init_and_add+0x70/0xb0
sysfs_slab_add+0xb1/0x250
__kmem_cache_create+0x116/0x150
create_cache+0xd9/0x1f0
kmem_cache_create_usercopy+0x1c1/0x250
kmem_cache_create+0x18/0x20
dm_bufio_client_create+0x1ae/0x410 [dm_bufio]
dm_block_manager_create+0x5e/0x90 [dm_persistent_data]
__create_persistent_data_objects+0x38/0x940 [dm_thin_pool]
dm_pool_abort_metadata+0x64/0x90 [dm_thin_pool]
metadata_operation_failed+0x59/0x100 [dm_thin_pool]
alloc_data_block.isra.53+0x86/0x180 [dm_thin_pool]
process_cell+0x2a3/0x550 [dm_thin_pool]
do_worker+0x28d/0x8f0 [dm_thin_pool]
process_one_work+0x171/0x370
worker_thread+0x49/0x3f0
kthread+0xf8/0x130
ret_from_fork+0x35/0x40
kobject_add_internal failed for :a-0000144 with -EEXIST, don't try to register things with the same name in the same directory.
kmem_cache_create(dm_bufio_buffer-16) failed with error -17
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1806151817130.6333@file01.intranet.prod.int.rdu2.redhat.com Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reported-by: Mike Snitzer <snitzer@redhat.com> Tested-by: Mike Snitzer <snitzer@redhat.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 3e5f06bed72fe72166a6778f630241a893f67799. As per
bugzilla #200045, this caused a regression. I don't really see a way to
fix it without having the hardware. So, revert the patch and I will fix
the issue I was seeing originally in the i2c-gpio driver itself. I
couldn't find new users of this algorithm since, so there should be no
one depending on the new behaviour.
Reported-by: Sergey Larin <cerg2010cerg2010@mail.ru> Fixes: 3e5f06bed72f ("i2c: algo-bit: init the bus to a known state") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Tested-by: Sergey Larin <cerg2010cerg2010@mail.ru> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have 3 more Lenovo machines, they all have 2 front mics on them,
so they need the fixup to change the location for one of two mics.
Among these 3 Lenovo machines, one of them has the same pin cfg as the
machine with subid 0x17aa3138, so use the pin cfg table to apply fixup
for them. The rest machines don't share the same pin cfg, so far use
the subid to apply fixup for them.
Fixes: a3dafb2200bf ("ALSA: hda/realtek - adjust the location of one mic") Cc: <stable@vger.kernel.org> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Lenovo laptops, e.g. Lenovo P50, showed the pop noise at resume
or runtime resume. It turned out to be reduced by applying
alc_no_shutup() just like TPT440 quirk does.
Since there are many Lenovo models showing the same behavior, put this
workaround in ALC269_FIXUP_THINKPAD_ACPI entry so that it's applied
commonly to all such Lenovo machines.
Reported-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Benjamin Berg <bberg@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Henning Kühn reported that the discrete AMD GPU on his hybrid graphics
laptop no longer runtime-suspends due to the recent commit 07f4f97d7b4b ("vga_switcheroo: Use device link for HDA controller").
The root cause is that the HDMI codec on AMD GPU doesn't support
CLKSTOP and EPSS, which are currently mandatory for powering down the
HD-audio link at runtime suspend. Because the HD-audio link is still
up, HD-audio controller driver blocks the transition to D3.
For addressing the regression, this patch adds a new flag to indicate
the forced link-down, and sets it for AMD HDMI codecs appropriately
in the codec driver.
The kernel may spew a WARNING about UBSAN undefined behavior at
handling ALSA timer ioctl SNDRV_TIMER_IOCTL_NEXT_DEVICE:
UBSAN: Undefined behaviour in sound/core/timer.c:1524:19
signed integer overflow: 2147483647 + 1 cannot be represented in type 'int'
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x122/0x1c8 lib/dump_stack.c:113
ubsan_epilogue+0x12/0x86 lib/ubsan.c:159
handle_overflow+0x1c2/0x21f lib/ubsan.c:190
__ubsan_handle_add_overflow+0x2a/0x31 lib/ubsan.c:198
snd_timer_user_next_device sound/core/timer.c:1524 [inline]
__snd_timer_user_ioctl+0x204d/0x2520 sound/core/timer.c:1939
snd_timer_user_ioctl+0x67/0x95 sound/core/timer.c:1994
....
It happens only when a value with INT_MAX is passed, as we're
incrementing it unconditionally. So the fix is trivial, check the
value with INT_MAX. Although the bug itself is fairly harmless, it's
better to fix it so that fuzzers won't hit this again later.
Commit 40f7090bb1b4 ("Input: elan_i2c_smbus - fix corrupted stack")
fixed most of the functions using i2c_smbus_read_block_data() to
allocate a buffer with the maximum block size. However three
functions were left unchanged:
* In elan_smbus_initialize(), increase the buffer size in the same
way.
* In elan_smbus_calibrate_result(), the buffer is provided by the
caller (calibrate_store()), so introduce a bounce buffer. Also
name the result buffer size.
* In elan_smbus_get_report(), the buffer is provided by the caller
but happens to be the right length. Add a compile-time assertion
to ensure this remains the case.
Cc: <stable@vger.kernel.org> # 3.19+ Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit ba667650c568 ("Input: psmouse - clean up code") was pretty
brain-dead and broke extra buttons reporting for variety of PS/2 mice:
Genius, Thinkmouse and Intellimouse Explorer. We need to actually inspect
the data coming from the device when reporting events.
SDL2 has a naive algorithm to apply the correct settings to a controller.
For X-Box compatible controllers it expects that the controller name
contains a variation of a 'XBOX'-string.
This patch changes the identifier to contain "X-Box" as substring. Tested
with Steam and C-Dogs-SDL which both detect the controller properly after
adding this patch.
Detect when a directory entry is (possibly partially) beyond directory
size and return EIO in that case since it means the filesystem is
corrupted. Otherwise directory operations can further corrupt the
directory and possibly also oops the kernel.
CC: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> CC: stable@vger.kernel.org Reported-and-tested-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts commit 3243ff2a05ec ("net: ethernet: davinci_emac:
Deduplicate bus_find_device() by name matching") and adds a comment
which should stop anyone from reintroducing the same "fix" in the future.
We can't use bus_find_device_by_name() here because the device name is
not guaranteed to be 'davinci_mdio'. On some systems it can be
'davinci_mdio.0' so we need to use strncmp() against the first part of
the string to correctly match it.
Fixes: 3243ff2a05ec ("net: ethernet: davinci_emac: Deduplicate bus_find_device() by name matching") Cc: stable@vger.kernel.org Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 910f8befdf5b ("xen/pirq: fix error path cleanup when binding
MSIs") fixed a couple of errors in error cleanup path of
xen_bind_pirq_msi_to_irq(). This cleanup allowed a call to
__unbind_from_irq() with an unbound irq, which would result in
triggering the BUG_ON there.
Since there is really no reason for the BUG_ON (xen_free_irq() can
operate on unbound irqs) we can remove it.
As that's the first reference to a "N-1" index, it appears that the code got
here with N = 0, which means the filter parser found no filter to parse
(which shouldn't ever happen, but apparently it did).
Add a new error to the parsing code that will check to make sure that N is
not zero before going into this part of the code. If N = 0, then -EINVAL is
returned, and a error message is added to the filter.
Cc: stable@vger.kernel.org Fixes: 80765597bc587 ("tracing: Rewrite filter logic to be simpler and faster") Reported-by: air icy <icytxw@gmail.com>
bugzilla url: https://bugzilla.kernel.org/show_bug.cgi?id=200019 Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I was poking around and for no real reason, I did cat /dev/mem and
strings /dev/mem. Then I saw the following warning in dmesg. I saved it
and rebooted immediately.
memremap attempted on mixed range 0x000000000009c000 size: 0x1000
------------[ cut here ]------------
WARNING: CPU: 0 PID: 11810 at kernel/memremap.c:98 memremap+0x104/0x170
[..]
Call Trace:
xlate_dev_mem_ptr+0x25/0x40
read_mem+0x89/0x1a0
__vfs_read+0x36/0x170
The memremap() implementation checks for attempts to remap System RAM
with MEMREMAP_WB and instead redirects those mapping attempts to the
linear map. However, that only works if the physical address range
being remapped is page aligned. In low memory we have situations like
the following:
...where System RAM intersects Reserved ranges on a sub-page page
granularity.
Given that devmem_is_allowed() special cases any attempt to map System
RAM in the first 1MB of memory, replace page_is_ram() with the more
precise region_intersects() to trap attempts to map disallowed ranges.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199999 Link: http://lkml.kernel.org/r/152856436164.18127.2847888121707136898.stgit@dwillia2-desk3.amr.corp.intel.com Fixes: 92281dee825f ("arch: introduce memremap()") Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reported-by: Hussam Al-Tayeb <me@hussam.eu.org> Tested-by: Hussam Al-Tayeb <me@hussam.eu.org> Cc: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In our armv8a server(QDF2400), I noticed lots of WARN_ON caused by
PAGE_SIZE unaligned for rmap_item->address under memory pressure
tests(start 20 guests and run memhog in the host).
In rmap_walk_ksm, the rmap_item->address might still have the
STABLE_FLAG, then the start and end in handle_hva_to_gpa might not be
PAGE_SIZE aligned. Thus it will cause exceptions in handle_hva_to_gpa
on arm64.
This patch fixes it by ignoring (not removing) the low bits of address
when doing rmap_walk_ksm.
IMO, it should be backported to stable tree. the storm of WARN_ONs is
very easy for me to reproduce. More than that, I watched a panic (not
reproducible) as follows:
I even injected a fault on purpose in kvm_unmap_hva_range by seting
size=size-0x200, the call trace is similar as above. So I thought the
panic is similarly caused by the root cause of WARN_ON.
Andrea said:
: It looks a straightforward safe fix, on x86 hva_to_gfn_memslot would
: zap those bits and hide the misalignment caused by the low metadata
: bits being erroneously left set in the address, but the arm code
: notices when that's the last page in the memslot and the hva_end is
: getting aligned and the size is below one page.
:
: I think the problem triggers in the addr += PAGE_SIZE of
: unmap_stage2_ptes that never matches end because end is aligned but
: addr is not.
:
: } while (pte++, addr += PAGE_SIZE, addr != end);
:
: x86 again only works on hva_start/hva_end after converting it to
: gfn_start/end and that being in pfn units the bits are zapped before
: they risk to cause trouble.
Jia He said:
: I've tested by myself in arm64 server (QDF2400,46 cpus,96G mem) Without
: this patch, the WARN_ON is very easy for reproducing. After this patch, I
: have run the same benchmarch for a whole day without any WARN_ONs
Link: http://lkml.kernel.org/r/1525403506-6750-1-git-send-email-hejianet@gmail.com Signed-off-by: Jia He <jia.he@hxt-semitech.com> Reviewed-by: Andrea Arcangeli <aarcange@redhat.com> Tested-by: Jia He <hejianet@gmail.com> Cc: Suzuki K Poulose <Suzuki.Poulose@arm.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> Cc: Arvind Yadav <arvind.yadav.cs@gmail.com> Cc: Mike Rapoport <rppt@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Move rbd_dev->watch_dwork cancellation so that rbd_reregister_watch()
either bails out early because the watch is UNREGISTERED at that point
or just gets cancelled. ]
On some devices the contents of the ctrl register get lost over a
suspend/resume and the PWM comes back up disabled after the resume.
This is seen on some Bay Trail devices with the PWM in ACPI enumerated
mode, so it shows up as a platform device instead of a PCI device.
If we still think it is enabled and then try to change the duty-cycle
after this, we end up with a "PWM_SW_UPDATE was not cleared" error and
the PWM is stuck in that state from then on.
This commit adds suspend and resume pm callbacks to the pwm-lpss-platform
code, which save/restore the ctrl register over a suspend/resume, fixing
this.
Note that:
1) There is no need to do this over a runtime suspend, since we
only runtime suspend when disabled and then we properly set the enable
bit and reprogram the timings when we re-enable the PWM.
2) This may be happening on more systems then we realize, but has been
covered up sofar by a bug in the acpi-lpss.c code which was save/restoring
the regular device registers instead of the lpss private registers due to
lpss_device_desc.prv_offset not being set. This is fixed by a later patch
in this series.
Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPSS PWM device on on Bay Trail and Cherry Trail devices has a set
of private registers at offset 0x800, the current lpss_device_desc for
them already sets the LPSS_SAVE_CTX flag to have these saved/restored
over device-suspend, but the current lpss_device_desc was not setting
the prv_offset field, leading to the regular device registers getting
saved/restored instead.
This is causing the PWM controller to no longer work, resulting in a black
screen, after a suspend/resume on systems where the firmware clears the
APB clock and reset bits at offset 0x804.
This commit fixes this by properly setting prv_offset to 0x800 for
the PWM devices.
The correct behaviour for NFSv4 sequence IDs is to wrap around
to the value 0 after 0xffffffff.
See https://tools.ietf.org/html/rfc5661#section-2.10.6.1
In nfs_idmap_read_and_verify_message there is an incorrect sprintf '%d'
that converts the __u32 'im_id' from struct idmap_msg to 'id_str', which
is a stack char array variable of length NFS_UINT_MAXLEN == 11.
If a uid or gid value is > 2147483647 = 0x7fffffff, the conversion
overflows into a negative value, for example:
crash> p (unsigned) (0x80000000)
$1 = 2147483648
crash> p (signed) (0x80000000)
$2 = -2147483648
The '-' sign is written to the buffer and this causes a 1 byte overflow
when the NULL byte is written, which corrupts kernel stack memory. If
CONFIG_CC_STACKPROTECTOR_STRONG is set we see a stack-protector panic:
Fix this by calling the internally defined nfs_map_numeric_to_string()
function which properly uses '%u' to convert this __u32. For consistency,
also replace the one other place where snprintf is called.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com> Reported-by: Stephen Johnston <sjohnsto@redhat.com> Fixes: cf4ab538f1516 ("NFSv4: Fix the string length returned by the idmapper") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nfsd4_readdir_rsize restricts rd_maxcount to svc_max_payload when
estimating the size of the readdir reply, but nfsd_encode_readdir
restricts it to INT_MAX when encoding the reply. This can result in log
messages like "kernel: RPC request reserved 32896 but used 1049444".
Restrict rd_dircount similarly (no reason it should be larger than
svc_max_payload).
Signed-off-by: Scott Mayhew <smayhew@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As warned by smatch:
drivers/media/dvb-core/dvb_frontend.c:314 dvb_frontend_get_event() warn: inconsistent returns 'sem:&fepriv->sem'.
Locked on: line 288
line 295
line 306
line 314
Unlocked on: line 303
The lock implementation for get event is wrong, as, if an
interrupt occurs, down_interruptible() will fail, and the
routine will call up() twice when userspace calls the ioctl
again.
The bad code is there since when Linux migrated to git, in
2005.
The MCE Remote sends a 0 scancode when keys are released. If this is not
received or decoded, then keys can get "stuck"; the keyup event is not
sent since the input_sync() is missing from the timeout handler.
Cc: stable@vger.kernel.org Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
media: uvcvideo: Support UVC 1.5 video probe & commit controls
The length of UVC 1.5 video control is 48, and it is 34 for UVC 1.1.
Change it to 48 for UVC 1.5 device, and the UVC 1.5 device can be
recognized.
More changes to the driver are needed for full UVC 1.5 compatibility.
However, at least the UVC 1.5 Realtek RTS5847/RTS5852 cameras have been
reported to work well.
[laurent.pinchart@ideasonboard.com: Factor out code to helper function, update size checks]
Commit 372b2b0399fc ("media: v4l: vsp1: Release buffers in
start_streaming error path") introduced a helper to clean up buffers on
error paths, but inadvertently changed the code such that only the
output WPF buffers were cleaned, rather than the video node being
operated on.
Since then vsp1_video_cleanup_pipeline() has grown to perform both video
node cleanup, as well as pipeline cleanup. Split the implementation into
two distinct functions that perform the required work, so that each
video node can release its buffers correctly on streamoff. The pipe
cleanup that was performed in the vsp1_video_stop_streaming() (releasing
the pipe->dl) is moved to the function for clarity.
Some Atom CPUs can produce FUP packets that contain NLIP (next linear
instruction pointer) instead of CLIP (current linear instruction
pointer). That will result in "Unexpected indirect branch" errors. Fix
by comparing IP to NLIP in that case.
On some platforms, overflows will clear before MTC wraparound, and there
is no following TSC/TMA packet. In that case the previous TMA is valid.
Since there will be a valid TMA either way, stop setting 'have_tma' to
false upon overflow.
projects / linux-stable / log