The size of the buffers for storing context's and sessions can vary from
arch to arch as PAGE_SIZE can be anything between 4 kB and 256 kB (the
maximum for PPC64). Define a fixed buffer size set to 16 kB. This should be
enough for most use with three handles (that is how many we allow at the
moment). Parametrize the buffer size while doing this, so that it is easier
to revisit this later on if required.
Cc: stable@vger.kernel.org Reported-by: Stefan Berger <stefanb@linux.ibm.com> Fixes: 745b361e989a ("tpm: infrastructure for TPM spaces") Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Tested-by: Stefan Berger <stefanb@linux.ibm.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The usb_request->zero doesn't apply for isoc. Also, if we prepare a
0-length (ZLP) TRB for the OUT direction, we need to prepare an extra
TRB to pad up to the MPS alignment. Use the same bounce buffer for the
ZLP TRB and the extra pad TRB.
The SG list may be set up with entry size more than the requested
length. Check the usb_request->length and make sure that we don't setup
the TRBs to send/receive more than requested. This case may occur when
the SG entry is allocated up to a certain minimum size, but the request
length is less than that. It can also occur when the request is reused
for a different request length.
With my new locking code dbench is so much faster that I tripped over a
transaction abort from ENOSPC. This turned out to be because
btrfs_del_dir_entries_in_log was checking for ret == -ENOSPC, but this
function sets err on error, and returns err. So instead of properly
marking the inode as needing a full commit, we were returning -ENOSPC
and aborting in __btrfs_unlink_inode. Fix this by checking the proper
variable so that we return the correct thing in the case of ENOSPC.
The ENOENT needs to be checked, because btrfs_lookup_dir_item_index()
can return -ENOENT if the dir item isn't in the tree log (which would
happen if we hadn't fsync'ed this guy). We actually handle that case in
__btrfs_unlink_inode, so it's an expected error to get back.
Fixes: 4a500fd178c8 ("Btrfs: Metadata ENOSPC handling for tree log") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ add note and comment about ENOENT ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PSZ-HA* family of USB disk drives from Sony can't handle the
REPORT OPCODES command when using the UAS protocol. This patch adds
an appropriate quirks entry.
Reported-and-tested-by: Till Dörges <doerges@pre-sense.de> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200826143229.GB400430@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdc-acm.c:409:3: warning: Use of memory after it is freed
acm_process_notification(acm, (unsigned char *)dr);
There are three problems, the first one is that dr is not reset
The variable dr is set with
if (acm->nb_index)
dr = (struct usb_cdc_notification *)acm->notification_buffer;
But if the notification_buffer is too small it is resized with
if (acm->nb_size) {
kfree(acm->notification_buffer);
acm->nb_size = 0;
}
alloc_size = roundup_pow_of_two(expected_size);
/*
* kmalloc ensures a valid notification_buffer after a
* use of kfree in case the previous allocation was too
* small. Final freeing is done on disconnect.
*/
acm->notification_buffer =
kmalloc(alloc_size, GFP_ATOMIC);
dr should point to the new acm->notification_buffer.
The second problem is any data in the notification_buffer is lost
when the pointer is freed. In the normal case, the current data
is accumulated in the notification_buffer here.
Inadvertently the commit b1cd1b65afba ("USB: gadget: u_f: add overflow checks
to VLA macros") makes VLA macros to always return 0 due to different scope of
two variables of the same name. Obviously we need to have only one.
Fixes: b1cd1b65afba ("USB: gadget: u_f: add overflow checks to VLA macros") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Brooke Basile <brookebasile@gmail.com> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20200826192119.56450-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some values extracted by ncm_unwrap_ntb() could possibly lead to several
different out of bounds reads of memory. Specifically the values passed
to netdev_alloc_skb_ip_align() need to be checked so that memory is not
overflowed.
Resolve this by applying bounds checking to a number of different
indexes and lengths of the structure parsing logic.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Brooke Basile <brookebasile@gmail.com> Acked-by: Felipe Balbi <balbi@kernel.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
size can potentially hold an overflowed value if its assigned expression
is left unchecked, leading to a smaller than needed allocation when
vla_group_size() is used by callers to allocate memory.
To fix this, add a test for saturation before declaring variables and an
overflow check to (n) * sizeof(type).
If the expression results in overflow, vla_group_size() will return SIZE_MAX.
If the function platform_get_irq() failed, the negative value
returned will not be detected here. So fix error handling in
exynos_ohci_probe(). And when get irq failed, the function
platform_get_irq() logs an error message, so remove redundant
message here.
This device does not support UAS properly and a similar entry already
exists in drivers/usb/storage/unusual_uas.h. Without this patch,
storage_probe() defers the handling of this device to UAS, which cannot
handle it either.
Tested-by: Brice Goglin <brice.goglin@gmail.com> Fixes: bc3bdb12bbb3 ("usb-storage: Disable UAS on JMicron SATA enclosure") Acked-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Cyril Roelandt <tipecaml@gmail.com> Link: https://lore.kernel.org/r/20200825212231.46309-1-tipecaml@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Sound Devices MixPre-D audio card suffers from the same defect
as the Sound Devices USBPre2: an endpoint shared between a normal
audio interface and a vendor-specific interface, in violation of the
USB spec. Since the USB core now treats duplicated endpoints as bugs
and ignores them, the audio endpoint isn't available and the card
can't be used for audio capture.
Along the same lines as commit bdd1b147b802 ("USB: quirks: blacklist
duplicate ep on Sound Devices USBPre2"), this patch adds a quirks
entry saying to ignore ep5in for interface 1, leaving it available for
use with standard audio interface 2.
There's another Raydium touchscreen needs the no-lpm quirk:
[ 1.339149] usb 1-9: New USB device found, idVendor=2386, idProduct=350e, bcdDevice= 0.00
[ 1.339150] usb 1-9: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.339151] usb 1-9: Product: Raydium Touch System
[ 1.339152] usb 1-9: Manufacturer: Raydium Corporation
...
[ 6.450497] usb 1-9: can't set config #1, error -110
PNY Pro Elite USB 3.1 Gen 2 device (SSD) doesn't respond to ATA_12
pass-through command (i.e. it just hangs). If it doesn't support this
command, it should respond properly to the host. Let's just add a quirk
to be able to move forward with other operations.
The syzbot fuzzer identified a bug in the yurex driver: It passes
GFP_KERNEL as a memory-allocation flag to usb_submit_urb() at a time
when its state is TASK_INTERRUPTIBLE, not TASK_RUNNING:
The values for "se_num" and "sh_num" come from the user in the ioctl.
They can be in the 0-255 range but if they're more than
AMDGPU_GFX_MAX_SE (4) or AMDGPU_GFX_MAX_SH_PER_SE (2) then it results in
an out of bounds read.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code, when the eoi callback of the exti clears the pending
bit of the current interrupt, it will first read the values of fpr and
rpr, then logically OR the corresponding bit of the interrupt number,
and finally write back to fpr and rpr.
We found through experiments that if two exti interrupts,
we call them int1/int2, arrive almost at the same time. in our scenario,
the time difference is 30 microseconds, assuming int1 is triggered first.
there will be an extreme scenario: both int's pending bit are set to 1,
the irq handle of int1 is executed first, and eoi handle is then executed,
at this moment, all pending bits are cleared, but the int 2 has not
finally been reported to the cpu yet, which eventually lost int2.
According to stm32's TRM description about rpr and fpr: Writing a 1 to this
bit will trigger a rising edge event on event x, Writing 0 has no
effect.
Therefore, when clearing the pending bit, we only need to clear the
pending bit of the irq.
Fixes: 927abfc4461e7 ("irqchip/stm32: Add stm32mp1 support with hierarchy domain") Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org # v4.18+ Link: https://lore.kernel.org/r/20200820031629.15582-1-qiuguorui1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the CPU mask operations behave the same way, but for_each_cpu() and
it's variants ignore the cpumask argument and claim that CPU0 is always in
the mask. This is historical, inconsistent and annoying behaviour.
The matrix allocator uses for_each_cpu() and can be called on UP with an
empty cpumask. The calling code does not expect that this succeeds but
until commit e027fffff799 ("x86/irq: Unbreak interrupt affinity setting")
this went unnoticed. That commit added a WARN_ON() to catch cases which
move an interrupt from one vector to another on the same CPU. The warning
triggers on UP.
Add a check for the cpumask being empty to prevent this.
When the primary firmware node pointer is removed from a
device (set to NULL) the secondary firmware node pointer,
when it exists, is made the primary node for the device.
However, the secondary firmware node pointer of the original
primary firmware node is never cleared (set to NULL).
To avoid situation where the secondary firmware node pointer
is pointing to a non-existing object, clearing it properly
when the primary node is removed from a device in
set_primary_fwnode().
Fixes: 97badf873ab6 ("device property: Make it possible to use secondary firmware nodes") Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been reported that system-wide suspend may be aborted in the
absence of any wakeup events due to unforseen interactions of it with
the runtume PM framework.
One failing scenario is when there are multiple devices sharing an
ACPI power resource and runtime-resume needs to be carried out for
one of them during system-wide suspend (for example, because it needs
to be reconfigured before the whole system goes to sleep). In that
case, the runtime-resume of that device involves turning the ACPI
power resource "on" which in turn causes runtime-resume requests
to be queued up for all of the other devices sharing it. Those
requests go to the runtime PM workqueue which is frozen during
system-wide suspend, so they are not actually taken care of until
the resume of the whole system, but the pm_runtime_barrier()
call in __device_suspend() sees them and triggers system wakeup
events for them which then cause the system-wide suspend to be
aborted if wakeup source objects are in active use.
Of course, the logic that leads to triggering those wakeup events is
questionable in the first place, because clearly there are cases in
which a pending runtime resume request for a device is not connected
to any real wakeup events in any way (like the one above). Moreover,
it is racy, because the device may be resuming already by the time
the pm_runtime_barrier() runs and so if the driver doesn't take care
of signaling the wakeup event as appropriate, it will be lost.
However, if the driver does take care of that, the extra
pm_wakeup_event() call in the core is redundant.
Accordingly, drop the conditional pm_wakeup_event() call fron
__device_suspend() and make the latter call pm_runtime_barrier()
alone. Also modify the comment next to that call to reflect the new
code and extend it to mention the need to avoid unwanted interactions
between runtime PM and system-wide device suspend callbacks.
Fixes: 1e2ef05bb8cf8 ("PM: Limit race conditions between runtime PM and system sleep (v2)") Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com> Tested-by: Utkarsh H Patel <utkarsh.h.patel@intel.com> Tested-by: Pengfei Xu <pengfei.xu@intel.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes re-plugging a USB device during system sleep renders the device
useless:
[ 173.418345] xhci_hcd 0000:00:14.0: Get port status 2-4 read: 0x14203e2, return 0x10262
...
[ 176.496485] usb 2-4: Waited 2000ms for CONNECT
[ 176.496781] usb usb2-port4: status 0000.0262 after resume, -19
[ 176.497103] usb 2-4: can't resume, status -19
[ 176.497438] usb usb2-port4: logical disconnect
Because PLS equals to XDEV_RESUME, xHCI driver reports U3 to usbcore,
despite of CAS bit is flagged.
So proritize CAS over XDEV_RESUME to let usbcore handle warm-reset for
the port.
handler data is meant for interrupt handlers and not for storing irq chip
specific information as some devices require handler data to store internal
per interrupt information, e.g. pinctrl/GPIO chained interrupt handlers.
This obviously creates a conflict of interests and crashes the machine
because the XEN pointer is overwritten by the driver pointer.
As the XEN data is not handler specific it should be stored in
irqdesc::irq_data::chip_data instead.
A simple sed s/irq_[sg]et_handler_data/irq_[sg]et_chip_data/ cures that.
Cc: stable@vger.kernel.org Reported-by: Roman Shaposhnik <roman@zededa.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Roman Shaposhnik <roman@zededa.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/87lfi2yckt.fsf@nanos.tec.linutronix.de Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we are processing writeback for sync(2), move_expired_inodes()
didn't set any inode expiry value (older_than_this). This can result in
writeback never completing if there's steady stream of inodes added to
b_dirty_time list as writeback rechecks dirty lists after each writeback
round whether there's more work to be done. Fix the problem by using
sync(2) start time is inode expiry value when processing b_dirty_time
list similarly as for ordinarily dirtied inodes. This requires some
refactoring of older_than_this handling which simplifies the code
noticeably as a bonus.
Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option") CC: stable@vger.kernel.org Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inode's i_io_list list head is used to attach inode to several different
lists - wb->{b_dirty, b_dirty_time, b_io, b_more_io}. When flush worker
prepares a list of inodes to writeback e.g. for sync(2), it moves inodes
to b_io list. Thus it is critical for sync(2) data integrity guarantees
that inode is not requeued to any other writeback list when inode is
queued for processing by flush worker. That's the reason why
writeback_single_inode() does not touch i_io_list (unless the inode is
completely clean) and why __mark_inode_dirty() does not touch i_io_list
if I_SYNC flag is set.
However there are two flaws in the current logic:
1) When inode has only I_DIRTY_TIME set but it is already queued in b_io
list due to sync(2), concurrent __mark_inode_dirty(inode, I_DIRTY_SYNC)
can still move inode back to b_dirty list resulting in skipping
writeback of inode time stamps during sync(2).
2) When inode is on b_dirty_time list and writeback_single_inode() races
with __mark_inode_dirty() like:
writeback_single_inode() __mark_inode_dirty(inode, I_DIRTY_PAGES)
inode->i_state |= I_SYNC
__writeback_single_inode()
inode->i_state |= I_DIRTY_PAGES;
if (inode->i_state & I_SYNC)
bail
if (!(inode->i_state & I_DIRTY_ALL))
- not true so nothing done
We end up with I_DIRTY_PAGES inode on b_dirty_time list and thus
standard background writeback will not writeback this inode leading to
possible dirty throttling stalls etc. (thanks to Martijn Coenen for this
analysis).
Fix these problems by tracking whether inode is queued in b_io or
b_more_io lists in a new I_SYNC_QUEUED flag. When this flag is set, we
know flush worker has queued inode and we should not touch i_io_list.
On the other hand we also know that once flush worker is done with the
inode it will requeue the inode to appropriate dirty list. When
I_SYNC_QUEUED is not set, __mark_inode_dirty() can (and must) move inode
to appropriate dirty list.
Reported-by: Martijn Coenen <maco@android.com> Reviewed-by: Martijn Coenen <maco@android.com> Tested-by: Martijn Coenen <maco@android.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option") CC: stable@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, operations on inode->i_io_list are protected by
wb->list_lock. In the following patches we'll need to maintain
consistency between inode->i_state and inode->i_io_list so change the
code so that inode->i_lock protects also all inode's i_io_list handling.
Reviewed-by: Martijn Coenen <maco@android.com> Reviewed-by: Christoph Hellwig <hch@lst.de> CC: stable@vger.kernel.org # Prerequisite for "writeback: Avoid skipping inode writeback" Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a number of "uart.port->desc.lock vs desc.lock->uart.port"
lockdep reports coming from 8250 driver; this causes a bit of trouble
to people, so let's fix it.
The problem is reverse lock order in two different call paths:
Fix this by changing the order of locks in serial8250_do_startup():
do disable_irq_nosync() first, which grabs desc->lock, and grab
uart->port after that, so that chain #1 and chain #2 have same lock
order.
Full lockdep splat:
======================================================
WARNING: possible circular locking dependency detected
5.4.39 #55 Not tainted
======================================================
swapper/0/0 is trying to acquire lock: ffffffffab65b6c0 (console_owner){-...}, at: console_lock_spinning_enable+0x31/0x57
but task is already holding lock: ffff88810a8e34c0 (&irq_desc_lock_class){-.-.}, at: __report_bad_irq+0x5b/0xba
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci") Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f12e ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f12e ("serial: pl011: add console matching function") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.10+ Cc: Aleksey Makarov <amakarov@marvell.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: Russell King <linux@armlinux.org.uk> Cc: Christopher Covington <cov@codeaurora.org> Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Tamseel Shams <m.shams@samsung.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vc_resize() can return with an error after failure. Change VT_RESIZEX ioctl
to save struct vc_data values that are modified and restore the original
values in case of error.
syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for
vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin().
Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access
vc->vc_pos when scroll is involved in order to manipulate cursor, but
vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets
updated based on the result of vc->vc_sw->con_set_origin().
Preserving old buffer and tolerating outdated vc members until set_origin()
completes would be easier than preventing vc->vc_sw->con_set_origin() from
accessing outdated vc members.
lvs_rh_probe() can return some nonnegative value from usb_control_msg()
when it is less than "USB_DT_HUB_NONVAR_SIZE + 2" that is considered as
a failure. Make lvs_rh_probe() return -EINVAL in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Add a check to fbcon_resize() to ensure that a possible change to user font
height or user font width will not allow a font data out-of-bounds access.
NOTE: must use original charcount in calculation as font charcount can
change and cannot be used to determine the font data allocated size.
If a transaction aborts it can cause a memory leak of the pages array of
a block group's io_ctl structure. The following steps explain how that can
happen:
1) Transaction N is committing, currently in state TRANS_STATE_UNBLOCKED
and it's about to start writing out dirty extent buffers;
2) Transaction N + 1 already started and another task, task A, just called
btrfs_commit_transaction() on it;
3) Block group B was dirtied (extents allocated from it) by transaction
N + 1, so when task A calls btrfs_start_dirty_block_groups(), at the
very beginning of the transaction commit, it starts writeback for the
block group's space cache by calling btrfs_write_out_cache(), which
allocates the pages array for the block group's io_ctl with a call to
io_ctl_init(). Block group A is added to the io_list of transaction
N + 1 by btrfs_start_dirty_block_groups();
4) While transaction N's commit is writing out the extent buffers, it gets
an IO error and aborts transaction N, also setting the file system to
RO mode;
5) Task A has already returned from btrfs_start_dirty_block_groups(), is at
btrfs_commit_transaction() and has set transaction N + 1 state to
TRANS_STATE_COMMIT_START. Immediately after that it checks that the
filesystem was turned to RO mode, due to transaction N's abort, and
jumps to the "cleanup_transaction" label. After that we end up at
btrfs_cleanup_one_transaction() which calls btrfs_cleanup_dirty_bgs().
That helper finds block group B in the transaction's io_list but it
never releases the pages array of the block group's io_ctl, resulting in
a memory leak.
In fact at the point when we are at btrfs_cleanup_dirty_bgs(), the pages
array points to pages that were already released by us at
__btrfs_write_out_cache() through the call to io_ctl_drop_pages(). We end
up freeing the pages array only after waiting for the ordered extent to
complete through btrfs_wait_cache_io(), which calls io_ctl_free() to do
that. But in the transaction abort case we don't wait for the space cache's
ordered extent to complete through a call to btrfs_wait_cache_io(), so
that's why we end up with a memory leak - we wait for the ordered extent
to complete indirectly by shutting down the work queues and waiting for
any jobs in them to complete before returning from close_ctree().
We can solve the leak simply by freeing the pages array right after
releasing the pages (with the call to io_ctl_drop_pages()) at
__btrfs_write_out_cache(), since we will never use it anymore after that
and the pages array points to already released pages at that point, which
is currently not a problem since no one will use it after that, but not a
good practice anyway since it can easily lead to use-after-free issues.
So fix this by freeing the pages array right after releasing the pages at
__btrfs_write_out_cache().
This issue can often be reproduced with test case generic/475 from fstests
and kmemleak can detect it and reports it with the following trace:
SCHED_RESTART code path is relied to re-run queue for dispatch requests
in hctx->dispatch. Meantime the SCHED_RSTART flag is checked when adding
requests to hctx->dispatch.
memory barriers have to be used for ordering the following two pair of OPs:
1) adding requests to hctx->dispatch and checking SCHED_RESTART in
blk_mq_dispatch_rq_list()
2) clearing SCHED_RESTART and checking if there is request in hctx->dispatch
in blk_mq_sched_restart().
Without the added memory barrier, either:
1) blk_mq_sched_restart() may miss requests added to hctx->dispatch meantime
blk_mq_dispatch_rq_list() observes SCHED_RESTART, and not run queue in
dispatch side
or
2) blk_mq_dispatch_rq_list still sees SCHED_RESTART, and not run queue
in dispatch side, meantime checking if there is request in
hctx->dispatch from blk_mq_sched_restart() is missed.
IO hang in ltp/fs_fill test is reported by kernel test robot:
https://lkml.org/lkml/2020/7/26/77
Turns out it is caused by the above out-of-order OPs. And the IO hang
can't be observed any more after applying this patch.
Fixes: bd166ef183c2 ("blk-mq-sched: add framework for MQ capable IO schedulers") Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Bart Van Assche <bvanassche@acm.org> Cc: Christoph Hellwig <hch@lst.de> Cc: David Jeffery <djeffery@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this commit i2c_hid_parse() consists of the following steps:
1. Send power on cmd
2. usleep_range(1000, 5000)
3. Send reset cmd
4. Wait for reset to complete (device interrupt, or msleep(100))
5. Send power on cmd
6. Try to read HID descriptor
Notice how there is an usleep_range(1000, 5000) after the first power-on
command, but not after the second power-on command.
Testing has shown that at least on the BMAX Y13 laptop's i2c-hid touchpad,
not having a delay after the second power-on command causes the HID
descriptor to read as all zeros.
In case we hit this on other devices too, the descriptor being all zeros
can be recognized by the following message being logged many, many times:
hid-generic 0018:0911:5288.0002: unknown main item tag 0x0
At the same time as the BMAX Y13's touchpad issue was debugged,
Kai-Heng was working on debugging some issues with Goodix i2c-hid
touchpads. It turns out that these need a delay after a PWR_ON command
too, otherwise they stop working after a suspend/resume cycle.
According to Goodix a delay of minimal 60ms is needed.
Having multiple cases where we need a delay after sending the power-on
command, seems to indicate that we should always sleep after the power-on
command.
This commit fixes the mentioned issues by moving the existing 1ms sleep to
the i2c_hid_set_power() function and changing it to a 60ms sleep.
Cc: stable@vger.kernel.org BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208247 Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reported-and-tested-by: Andrea Borgia <andrea@borgia.bo.it> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of block device backend, if the backend supports write zeros, the
loop device will set queue flag of QUEUE_FLAG_DISCARD. However,
limits.discard_granularity isn't setup, and this way is wrong,
see the following description in Documentation/ABI/testing/sysfs-block:
A discard_granularity of 0 means that the device does not support
discard functionality.
Especially 9b15d109a6b2 ("block: improve discard bio alignment in
__blkdev_issue_discard()") starts to take q->limits.discard_granularity
for computing max discard sectors. And zero discard granularity may cause
kernel oops, or fail discard request even though the loop queue claims
discard support via QUEUE_FLAG_DISCARD.
Fix the issue by setup discard granularity and alignment.
Fixes: c52abf563049 ("loop: Better discard support for block devices") Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Coly Li <colyli@suse.de> Cc: Hannes Reinecke <hare@suse.com> Cc: Xiao Ni <xni@redhat.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Evan Green <evgreen@chromium.org> Cc: Gwendal Grignou <gwendal@chromium.org> Cc: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com> Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com> Cc: Christoph Hellwig <hch@lst.de> Cc: <stable@vger.kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Performance monitor interrupt handler checks if any counter has
overflown and calls record_and_restart() in core-book3s which invokes
perf_event_overflow() to record the sample information. Apart from
creating sample, perf_event_overflow() also does the interrupt and
period checks via perf_event_account_interrupt().
Currently we record information only if the SIAR (Sampled Instruction
Address Register) valid bit is set (using siar_valid() check) and
hence the interrupt check.
But it is possible that we do sampling for some events that are not
generating valid SIAR, and hence there is no chance to disable the
event if interrupts are more than max_samples_per_tick. This leads to
soft lockup.
Fix this by adding perf_event_account_interrupt() in the invalid SIAR
code path for a sampling event. ie if SIAR is invalid, just do
interrupt check and don't record the sample information.
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Remote source MAC addresses can be set on a 'source mode' macvlan
interface via the IFLA_MACVLAN_MACADDR_DATA attribute. This commit
tightens the validation of these MAC addresses to match the validation
already performed when setting or adding a single MAC address via the
IFLA_MACVLAN_MACADDR attribute.
iproute2 uses IFLA_MACVLAN_MACADDR_DATA for its 'macvlan macaddr set'
command, and IFLA_MACVLAN_MACADDR for its 'macvlan macaddr add' command,
which demonstrates the inconsistent behaviour that this commit
addresses:
# ip link add link eth0 name macvlan0 type macvlan mode source
# ip link set link dev macvlan0 type macvlan macaddr add 01:00:00:00:00:00
RTNETLINK answers: Cannot assign requested address
# ip link set link dev macvlan0 type macvlan macaddr set 01:00:00:00:00:00
# ip -d link show macvlan0
5: macvlan0@eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 ...
link/ether 2e:ac:fd:2d:69:f8 brd ff:ff:ff:ff:ff:ff promiscuity 0
macvlan mode source remotes (1) 01:00:00:00:00:00 numtxqueues 1 ...
With this change, the 'set' command will (rightly) fail in the same way
as the 'add' command.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
FCoE adapter initialization failed for ISP8021 with the following patch
applied. In addition, reproduction of the issue the patch originally tried
to address has been unsuccessful.
NVMEAsync command is being submitted to QLA while the same NVMe controller
is in the middle of reset. The reset path has deleted the association and
freed aen_op->fcp_req.private. Add a check for this private pointer before
issuing the command.
OS boot during Boot from SAN was stuck at dracut emergency shell after
enabling NVMe driver parameter. For non-MQ support the driver was enabling
MQ. Add a check to confirm if FW supports MQ.
If somehow no interrupt notification is raised for a completed request and
its doorbell bit is cleared by host, UFS driver needs to cleanup its
outstanding bit in ufshcd_abort(). Otherwise, system may behave abnormally
in the following scenario:
After ufshcd_abort() returns, this request will be requeued by SCSI layer
with its outstanding bit set. Any future completed request will trigger
ufshcd_transfer_req_compl() to handle all "completed outstanding bits". At
this time the "abnormal outstanding bit" will be detected and the "requeued
request" will be chosen to execute request post-processing flow. This is
wrong because this request is still "alive".
Link: https://lore.kernel.org/r/20200811141859.27399-2-huobean@gmail.com Reviewed-by: Can Guo <cang@codeaurora.org> Acked-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Bean Huo <beanhuo@micron.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In ufshcd_suspend(), after clk-gating is suspended and link is set
as Hibern8 state, ufshcd_hold() is still possibly invoked before
ufshcd_suspend() returns. For example, MediaTek's suspend vops may
issue UIC commands which would call ufshcd_hold() during the command
issuing flow.
Now if UFSHCD_CAP_HIBERN8_WITH_CLK_GATING capability is enabled,
then ufshcd_hold() may enter infinite loops because there is no
clk-ungating work scheduled or pending. In this case, ufshcd_hold()
shall just bypass, and keep the link as Hibern8 state.
Link: https://lore.kernel.org/r/20200809050734.18740-1-stanley.chu@mediatek.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Co-developed-by: Andy Teng <andy.teng@mediatek.com> Signed-off-by: Andy Teng <andy.teng@mediatek.com> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ixgbe_fcoe_ddp_setup() can be called from the main I/O path and is called
with a spin_lock held, so we have to use GFP_ATOMIC allocation instead of
GFP_KERNEL.
The driver supports WM1811, WM8994, WM8958 devices but according to
documentation and the regmap definitions the WM8958_DSP2_* registers
are only available on WM8958. In current code these registers are
being accessed as if they were available on all the three chips.
When starting playback on WM1811 CODEC multiple errors like:
"wm8994-codec wm8994-codec: ASoC: error at soc_component_read_no_lock on wm8994-codec: -5"
can be seen, which is caused by attempts to read an unavailable
WM8958_DSP2_PROGRAM register. The issue has been uncovered by recent
commit "e2329ee ASoC: soc-component: add soc_component_err()".
This patch adds a check in wm8958_aif_ev() callback so the DSP2 handling
is only done for WM8958.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/20200731173834.23832-1-s.nawrocki@samsung.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The scanning through subchannels during the time of an event could
take significant amount of time in case of platforms with lots of
known subchannels. This might result in higher scheduling latencies
for other tasks especially on systems with a single CPU. Add
cond_resched() call, as the loop in slow_eval_known_fn() can be
executed for a longer duration.
If a device is hot-removed --- for example, when a physical device is
unplugged from pcie slot or a nbd device's network is shutdown ---
this can result in a BUG_ON() crash in submit_bh_wbc(). This is
because the when the block device dies, the buffer heads will have
their Buffer_Mapped flag get cleared, leading to the crash in
submit_bh_wbc.
We had attempted to work around this problem in commit a17712c8
("ext4: check superblock mapped prior to committing"). Unfortunately,
it's still possible to hit the BUG_ON(!buffer_mapped(bh)) if the
device dies between when the work-around check in ext4_commit_super()
and when submit_bh_wbh() is finally called:
Code path:
ext4_commit_super
judge if 'buffer_mapped(sbh)' is false, return <== commit a17712c8
lock_buffer(sbh)
...
unlock_buffer(sbh)
__sync_dirty_buffer(sbh,...
lock_buffer(sbh)
judge if 'buffer_mapped(sbh))' is false, return <== added by this patch
submit_bh(...,sbh)
submit_bh_wbc(...,sbh,...)
When remounting filesystem fails late during remount handling and
block_validity mount option is also changed during the remount, we fail
to restore system zone information to a state matching the mount option.
This is mostly harmless, just the block validity checking will not match
the situation described by the mount option. Make sure these two are always
consistent.
Fix it by applying the SB_LAZYTIME and SB_I_VERSION flags from *flags to
s_flags before we parse the option and use the resulting state of the
same flags in *flags at the end of successful remount.
If we free a metadata buffer which has been failed to async write out
in the background, the jbd2 checkpoint procedure will not detect this
failure in jbd2_log_do_checkpoint(), so it may lead to filesystem
inconsistency after cleanup journal tail. This patch abort the journal
if free a buffer has write_io_error flag to prevent potential further
inconsistency.
Ext4 uses blkdev_get_by_dev() to get the block_device for journal device
which does check to see if the read-only block device was opened
read-only.
As a result ext4 will hapily proceed mounting the file system with
external journal on read-only device. This is bad as we would not be
able to use the journal leading to errors later on.
Instead of simply failing to mount file system in this case, treat it in
a similar way we treat internal journal on read-only device. Allow to
mount with -o noload in read-only mode.
A customer has reported a BUG_ON in ext4_clear_journal_err() hitting
during an LTP testing. Either this has been caused by a test setup
issue where the filesystem was being overwritten while LTP was mounting
it or the journal replay has overwritten the superblock with invalid
data. In either case it is preferable we don't take the machine down
with a BUG_ON. So handle the situation of unexpectedly missing
has_journal feature more gracefully. We issue warning and fail the mount
in the cases where the race window is narrow and the failed check is
most likely a programming error. In cases where fs corruption is more
likely, we do full ext4_error() handling before failing mount / remount.
Reviewed-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20200710140759.18031-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
Callers of __jbd2_journal_unfile_buffer() and
__jbd2_journal_refile_buffer() assume that the b_transaction is set. In
fact if it's not, we can end up with journal_head refcounting errors
leading to crash much later that might be very hard to track down. Add
asserts to make sure that is the case.
We also make sure that b_next_transaction is NULL in
__jbd2_journal_unfile_buffer() since the callers expect that as well and
we should not get into that stage in this state anyway, leading to
problems later on if we do.
Currently, a NACK in slave mode is set/cleared when SCL is held low by
the IP core right before the bit is about to be pushed out. This is too
late for clearing and then a NACK from the previous byte is still used
for the current one. Now, let's clear the NACK right after we detected
the STOP condition following the NACK.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to set it to the most recent completed fence, not the most
recent submitted. Otherwise we have races where we think we can retire
submits that the GPU is not finished with, if the GPU doesn't manage to
overwrite the seqno before we look at it.
This can show up with hang recovery if one of the submits after the
crashing submit also hangs after it is replayed.
Fixes: f97decac5f4c ("drm/msm: Support multiple ringbuffers") Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
usleep_range() may take longer than the max argument due to scheduling,
especially under load. This is causing random errors in the transmitted
IR. Remove the usleep_range() in favour of busy-looping with udelay().
Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 76d164f582150fd0259ec0fcbc485470bcd8033e.
PCIe hung issue was observed on multiple platforms. The issue was reproduced
when DUT was configured as AP and associated with 50+ STAs.
For QCA9984/QCA9888, the DMA_BURST_SIZE register controls the AXI burst size
of the RD/WR access to the HOST MEM.
0 - No split , RAW read/write transfer size from MAC is put out on bus
as burst length
1 - Split at 256 byte boundary
2,3 - Reserved
With PCIe protocol analyzer, we can see DMA Read crossing 4KB boundary when
issue happened. It broke PCIe spec and caused PCIe stuck. So revert
the default value from 0 to 1.
Tested: IPQ8064 + QCA9984 with firmware 10.4-3.10-00047
QCS404 + QCA9984 with firmware 10.4-3.9.0.2--00044
Synaptics AS370 + QCA9888 with firmware 10.4-3.9.0.2--00040
Signed-off-by: Zhi Chen <zhichen@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_EFI is not enabled, we might get an undefined reference to
efi_enter_virtual_mode() error, if this efi_enabled() call isn't inlined
into start_kernel(). This happens in particular, if start_kernel() is
annodated with __no_sanitize_address.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Elena Petrova <lenaptr@google.com> Cc: Marco Elver <elver@google.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: Walter Wu <walter-zh.wu@mediatek.com> Link: http://lkml.kernel.org/r/6514652d3a32d3ed33d6eb5c91d0af63bf0d1a0c.1596544734.git.andreyknvl@google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The char buffer buf, receives data directly from user space,
so its content might be negative and its elements are left
shifted to form an unsigned integer.
Since left shifting a negative value is undefined behavior, thus
change the char to u8 to elimintate this UB.
The kernel test robot pointed out a slightly different error message
after recent commit 5456ffdee666 ("powerpc/spufs: simplify spufs core
dumping") to spufs for a configuration that never worked:
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_proxydma_info_dump':
>> file.c:(.text+0x4c68): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_dma_info_dump':
file.c:(.text+0x4d70): undefined reference to `.dump_emit'
powerpc64-linux-ld: arch/powerpc/platforms/cell/spufs/file.o: in function `.spufs_wbox_info_dump':
file.c:(.text+0x4df4): undefined reference to `.dump_emit'
Add a Kconfig dependency to prevent this from happening again.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200706132302.3885935-1-arnd@arndb.de Signed-off-by: Sasha Levin <sashal@kernel.org>
__hyp_call_panic_nvhe contains inline assembly which did not declare
its dependency on the __hyp_panic_string symbol.
The static-declared string has previously been kept alive because of a use in
__hyp_call_panic_vhe. Fix this in preparation for separating the source files
between VHE and nVHE when the two users land in two different compilation
units. The static variable otherwise gets dropped when compiling the nVHE
source file, causing an undefined symbol linker error later.
The Intel uncore driver may claim some of the pci ids from ie31200 which
means that the ie31200 edac driver will not initialize them as part of
pci_register_driver().
Let's add a fallback for this case to 'pci_get_device()' to get a
reference on the device such that it can still be configured. This is
similar in approach to other edac drivers.
Make sure the delayed work stopped before releasing the resources.
cancel_delayed_work_sync() will only guarantee that the work finishes
executing if the work is already in the ->worklist. That means after
the cancel_delayed_work_sync() returns, it will leave the work requeued
if it was rearmed at the end. That can lead to a use after free once the
work struct is freed.
Fix it by flushing the delayed work instead of trying to cancel it, and
ensure that the work doesn't rearm if the mdsc is stopping.
URL: https://tracker.ceph.com/issues/46293 Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The incoming qgroup reserved space timing will move the data reservation
to ordered extent completely.
However in btrfs_punch_hole_lock_range() will call
btrfs_invalidate_page(), which will clear QGROUP_RESERVED bit for the
range.
In current stage it's OK, but if we're making ordered extents handle the
reserved space, then btrfs_punch_hole_lock_range() can clear the
QGROUP_RESERVED bit before we submit ordered extent, leading to qgroup
reserved space leakage.
So here change the timing to make reserve data space after
btrfs_punch_hole_lock_range().
The new timing is fine for either current code or the new code.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Though the number of lock-acquisitions is tracked as unsigned long, this
is passed as the divisor to div_s64() which interprets it as a s32,
giving nonsense values with more than 2 billion acquisitons. E.g.
nouveau_connector_detect() calls pm_runtime_get_sync and in turn
increments the reference count. In case of failure, decrement the
ref count before returning the error.
nv50_disp_atomic_commit() calls calls pm_runtime_get_sync and in turn
increments the reference count. In case of failure, decrement the
ref count before returning the error.
nouveau_fbcon_open() calls calls pm_runtime_get_sync() that
increments the reference count. In case of failure, decrement the
ref count before returning the error.
During umount, f2fs_put_super() unregisters procfs entries after
f2fs_destroy_segment_manager(), it may cause use-after-free
issue when umount races with procfs accessing, fix it by relocating
f2fs_unregister_sysfs().
[Chao Yu: change commit title/message a bit]
Signed-off-by: Li Guifu <bluce.liguifu@huawei.com> Reviewed-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Logitech GROUP is a compound with camera and audio.
When the HID interface in an audio device is requested to get
specific report id, all following control transfers are stalled
and never be restored back.
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse.
To use the TMR_FIPER register to generate desired periodic
pulses. The value should programmed is,
desired_period - tclk_period
Current tmr-fiper2 value is to generate 100us periodic pulses.
(But the value should have been 99995, not 99990. The tclk_period is 5.)
This patch is to generate 1 second periodic pulses with value 999999995 programmed which is more desired by user.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
kobject_init_and_add() takes a reference even when it fails. If it returns
an error, kobject_put() must be called to clean up the memory associated
with the object.
When kobject_init_and_add() fails, call kobject_put() instead of kfree().
b8eb718348b8 ("net-sysfs: Fix reference count leak in
rx|netdev_queue_add_kobject") fixed a similar problem.
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
- don't panic kernel if f2fs_get_node_page() fails in
f2fs_recover_inline_data() or f2fs_recover_inline_xattr();
- return error number of f2fs_truncate_blocks() to
f2fs_recover_inline_data()'s caller;
An extra count on ebb_state.stats.pmc_count[PMC_INDEX(pmc)] is being per-
formed when count_pmc() is used to reset PMCs on a few selftests. This
extra pmc_count can occasionally invalidate results, such as the ones from
cycles_test shown hereafter. The ebb_check_count() failed with an above
the upper limit error due to the extra value on ebb_state.stats.pmc_count.
Furthermore, this extra count is also indicated by extra PMC1 trace_log on
the output of the cycle test (as well as on pmc56_overflow_test):
In tracking down a problem in this patchset, I discovered we are
reclaiming dirty stale inodes. This wasn't discovered until inodes
were always attached to the cluster buffer and then the rcu callback
that freed inodes was assert failing because the inode still had an
active pointer to the cluster buffer after it had been reclaimed.
Debugging the issue indicated that this was a pre-existing issue
resulting from the way the inodes are handled in xfs_inactive_ifree.
When we free a cluster buffer from xfs_ifree_cluster, all the inodes
in cache are marked XFS_ISTALE. Those that are clean have nothing
else done to them and so eventually get cleaned up by background
reclaim. i.e. it is assumed we'll never dirty/relog an inode marked
XFS_ISTALE.
On journal commit dirty stale inodes as are handled by both
buffer and inode log items to run though xfs_istale_done() and
removed from the AIL (buffer log item commit) or the log item will
simply unpin it because the buffer log item will clean it. What happens
to any specific inode is entirely dependent on which log item wins
the commit race, but the result is the same - stale inodes are
clean, not attached to the cluster buffer, and not in the AIL. Hence
inode reclaim can just free these inodes without further care.
However, if the stale inode is relogged, it gets dirtied again and
relogged into the CIL. Most of the time this isn't an issue, because
relogging simply changes the inode's location in the current
checkpoint. Problems arise, however, when the CIL checkpoints
between two transactions in the xfs_inactive_ifree() deferops
processing. This results in the XFS_ISTALE inode being redirtied
and inserted into the CIL without any of the other stale cluster
buffer infrastructure being in place.
Hence on journal commit, it simply gets unpinned, so it remains
dirty in memory. Everything in inode writeback avoids XFS_ISTALE
inodes so it can't be written back, and it is not tracked in the AIL
so there's not even a trigger to attempt to clean the inode. Hence
the inode just sits dirty in memory until inode reclaim comes along,
sees that it is XFS_ISTALE, and goes to reclaim it. This reclaiming
of a dirty inode caused use after free, list corruptions and other
nasty issues later in this patchset.
Hence this patch addresses a violation of the "never log XFS_ISTALE
inodes" caused by the deferops processing rolling a transaction
and relogging a stale inode in xfs_inactive_free. It also adds a
bunch of asserts to catch this problem in debug kernels so that
we don't reintroduce this problem in future.
Reproducer for this issue was generic/558 on a v4 filesystem.
Signed-off-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When vports are deleted, it is observed that there is memory/kthread
leakage as the vport isn't fully being released.
There is a shost reference taken in scsi_add_host_dma that is not released
during scsi_remove_host. It was noticed that other drivers resolve this by
doing a scsi_host_put after calling scsi_remove_host.
The vport_delete routine is taking two references one that corresponds to
an access to the scsi_host in the vport_delete routine and another that is
released after the adapter mailbox command completes that destroys the VPI
that corresponds to the vport.
Remove one of the references taken such that the second reference that is
put will complete the missing scsi_add_host_dma reference and the shost
will be terminated.
Link: https://lore.kernel.org/r/20200630215001.70793-8-jsmart2021@gmail.com Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log