Since commit dfeae1073583("mtd: cfi_cmdset_0002: Change write buffer to
check correct value") buffered writes fail on S29GL064N. This is
because, on S29GL064N, reads return 0xFF at the end of DQ polling for
write completion, where as, chip_good() check expects actual data
written to the last location to be returned post DQ polling completion.
Fix is to revert to using chip_good() for S29GL064N which only checks
for DQ lines to settle down to determine write completion.
The RAID0 layout is irrelevant if all members have the same size so the
array has only one zone. It is *also* irrelevant if the array has two
zones and the second zone has only one device, for example if the array
has two members of different sizes.
So in that case it makes sense to allow assembly even when the layout is
undefined, like what is done when the array has only one zone.
Reviewed-by: NeilBrown <neilb@suse.de> Signed-off-by: Pascal Hambourg <pascal@plouf.fr.eu.org> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ptrace PEEKUSR/POKEUSR (aka PEEKUSER/POKEUSER) API allows a process
to read/write registers of another process.
To get/set a register, the API takes an index into an imaginary address
space called the "USER area", where the registers of the process are
laid out in some fashion.
The kernel then maps that index to a particular register in its own data
structures and gets/sets the value.
The API only allows a single machine-word to be read/written at a time.
So 4 bytes on 32-bit kernels and 8 bytes on 64-bit kernels.
The way floating point registers (FPRs) are addressed is somewhat
complicated, because double precision float values are 64-bit even on
32-bit CPUs. That means on 32-bit kernels each FPR occupies two
word-sized locations in the USER area. On 64-bit kernels each FPR
occupies one word-sized location in the USER area.
Internally the kernel stores the FPRs in an array of u64s, or if VSX is
enabled, an array of pairs of u64s where one half of each pair stores
the FPR. Which half of the pair stores the FPR depends on the kernel's
endianness.
To handle the different layouts of the FPRs depending on VSX/no-VSX and
big/little endian, the TS_FPR() macro was introduced.
Unfortunately the TS_FPR() macro does not take into account the fact
that the addressing of each FPR differs between 32-bit and 64-bit
kernels. It just takes the index into the "USER area" passed from
userspace and indexes into the fp_state.fpr array.
On 32-bit there are 64 indexes that address FPRs, but only 32 entries in
the fp_state.fpr array, meaning the user can read/write 256 bytes past
the end of the array. Because the fp_state sits in the middle of the
thread_struct there are various fields than can be overwritten,
including some pointers. As such it may be exploitable.
It has also been observed to cause systems to hang or otherwise
misbehave when using gdbserver, and is probably the root cause of this
report which could not be easily reproduced:
https://lore.kernel.org/linuxppc-dev/dc38afe9-6b78-f3f5-666b-986939e40fc6@keymile.com/
Rather than trying to make the TS_FPR() macro even more complicated to
fix the bug, or add more macros, instead add a special-case for 32-bit
kernels. This is more obvious and hopefully avoids a similar bug
happening again in future.
Note that because 32-bit kernels never have VSX enabled the code doesn't
need to consider TS_FPRWIDTH/OFFSET at all. Add a BUILD_BUG_ON() to
ensure that 32-bit && VSX is never enabled.
Fixes: 87fec0514f61 ("powerpc: PTRACE_PEEKUSR/PTRACE_POKEUSER of FPR registers in little endian builds") Cc: stable@vger.kernel.org # v3.13+ Reported-by: Ariel Miculas <ariel.miculas@belden.com> Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220609133245.573565-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm5974 driver does the allocation and dma mapping of the usb urb
data buffer, but driver does not set the URB_NO_TRANSFER_DMA_MAP flag
to let usb core know the buffer is already mapped.
usb core tries to map the already mapped buffer, causing a warning:
"xhci_hcd 0000:00:14.0: rejecting DMA map of vmalloc memory"
Fix this by setting the URB_NO_TRANSFER_DMA_MAP, letting usb core
know buffer is already mapped by bcm5974 driver
When the promiscuous mode is enabled on a VF, the IXGBE_VMOLR_VPE
bit (VLAN Promiscuous Enable) is set. This means that the VF will
receive packets whose VLAN is not the same than the VLAN of the VF.
If we tcpdump on VF3, we see all the packets, even those transmitted
on vlan 1000.
This behavior prevents to bridge VF1 and VF2 in VM2, because it will
create a loop: packets transmitted on VF1 will be received by VF2 and
vice-versa, and bridged again through the software bridge.
This patch remove the activation of VLAN Promiscuous when a VF enables
the promiscuous mode. However, the IXGBE_VMOLR_UPE bit (Unicast
Promiscuous) is kept, so that a VF receives all packets that has the
same VLAN, whatever the destination MAC address.
Fixes: 8443c1a4b192 ("ixgbe, ixgbevf: Add new mbox API xcast mode") Cc: stable@vger.kernel.org Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a VF requested to remove the promiscuous flag on an interface, the
broadcast packets are not received anymore. This breaks some protocols
like ARP.
In ixgbe_update_vf_xcast_mode(), we should keep the IXGBE_VMOLR_BAM
bit (Broadcast Accept) on promiscuous removal.
This flag is already set by default in ixgbe_set_vmolr() on VF reset.
Fixes: 8443c1a4b192 ("ixgbe, ixgbevf: Add new mbox API xcast mode") Cc: stable@vger.kernel.org Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Olivier Matz <olivier.matz@6wind.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first validation check for EVT_TRANSACTION has two different checks
tied together with logical AND. One is a check for minimum packet length,
and the other is for a valid aid_tag. If either condition is true (fails),
then an error should be triggered. The fix is to change && to ||.
The intention of the use of mmc_blk_reset_success() in
mmc_blk_cqe_recovery() was to prevent repeated resets when retrying and
getting the same error. However, that may not be the case - any amount
of time and I/O may pass before another recovery is needed, in which
case there would be no reason to deny it the opportunity to recover via
a reset if necessary. CQE recovery is expected seldom and failure to
recover (if the clear tasks command fails), even more seldom, so it is
better to allow the reset always, which can be done by calling
mmc_blk_reset_success() always.
The {dma|pio}_mode sysfs files are incorrectly documented as having a
list of the supported DMA/PIO transfer modes, while the corresponding
fields of the *struct* ata_device hold the transfer mode IDs, not masks.
To match these docs, the {dma|pio}_mode (and even xfer_mode!) sysfs
files are handled by the ata_bitfield_name_match() macro which leads to
reading such kind of nonsense from them:
While fixing the file documentation, somewhat reword the {dma|pio}_mode
file doc and add a note about being mostly useful for PATA devices to
the xfer_mode file doc...
Fixes: d9027470b886 ("[libata] Add ATA transport class") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During reconnects, we check the return value from
cifs_negotiate_protocol, and have handlers for both success
and failures. But if that passes, and cifs_setup_session
returns any errors other than -EACCES, we do not handle
that. This fix adds a handler for that, so that we don't
go ahead and try a tree_connect on a failed session.
Signed-off-by: Shyam Prasad N <sprasad@microsoft.com> Reviewed-by: Enzo Matsumiya <ematsumiya@suse.de> Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should use size of descriptor chain to test loop condition
in the indirect case. And another statistical count is also introduced
for indirect descriptors to avoid conflict with the statistical count
of direct descriptors.
Fixes: f87d0fbb5798 ("vringh: host-side implementation of virtio rings.") Signed-off-by: Xie Yongji <xieyongji@bytedance.com> Signed-off-by: Fam Zheng <fam.zheng@bytedance.com>
Message-Id: <20220505100910.137-1-xieyongji@bytedance.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The nodemask routines had mixed return values that provided potentially
signed return values that could never happen. This was leading to the
compiler getting confusing about the range of possible return values
(it was thinking things could be negative where they could not be). Fix
all the nodemask routines that should be returning unsigned
(or bool) values. Silences:
mm/swapfile.c: In function ‘setup_swap_info’:
mm/swapfile.c:2291:47: error: array subscript -1 is below array bounds of ‘struct plist_node[]’ [-Werror=array-bounds]
2291 | p->avail_lists[i].prio = 1;
| ~~~~~~~~~~~~~~^~~
In file included from mm/swapfile.c:16:
./include/linux/swap.h:292:27: note: while referencing ‘avail_lists’
292 | struct plist_node avail_lists[]; /*
| ^~~~~~~~~~~
"qemu-ndb -d" will call ioctl 'NBD_DISCONNECT' first, however, following
message was found:
block nbd0: Send disconnect failed -32
Which indicate that something is wrong with the server. Then,
"qemu-nbd -d" will call ioctl 'NBD_CLEAR_SOCK', however ioctl can't clear
requests after commit 2516ab1543fd("nbd: only clear the queue on device
teardown"). And in the meantime, request can't complete through timeout
because nbd_xmit_timeout() will always return 'BLK_EH_RESET_TIMER', which
means such request will never be completed in this situation.
Now that the flag 'NBD_CMD_INFLIGHT' can make sure requests won't
complete multiple times, switch back to call nbd_clear_sock() in
nbd_clear_sock_ioctl(), so that inflight requests can be cleared.
When nbd module is being removing, nbd_alloc_config() may be
called concurrently by nbd_genl_connect(), although try_module_get()
will return false, but nbd_alloc_config() doesn't handle it.
The race may lead to the leak of nbd_config and its related
resources (e.g, recv_workq) and oops in nbd_read_stat() due
to the unload of nbd module as shown below:
Fixing it by checking the return value of try_module_get()
in nbd_alloc_config(). As nbd_alloc_config() may return ERR_PTR(-ENODEV),
assign nbd->config only when nbd_alloc_config() succeeds to ensure
the value of nbd->config is binary (valid or NULL).
Also adding a debug message to check the reference counter
of nbd_config during module removal.
The return value of is_arm_mapping_symbol() is unpredictable when "$"
is passed in.
strchr(3) says:
The strchr() and strrchr() functions return a pointer to the matched
character or NULL if the character is not found. The terminating null
byte is considered part of the string, so that if c is specified as
'\0', these functions return a pointer to the terminator.
When str[1] is '\0', strchr("axtd", str[1]) is not NULL, and str[2] is
referenced (i.e. buffer overrun).
In radeon_fp_native_mode(), the return value of drm_mode_duplicate()
is assigned to mode, which will lead to a NULL pointer dereference
on failure of drm_mode_duplicate(). Add a check to avoid npd.
The failure status of drm_cvt_mode() on the other path is checked too.
Signed-off-by: Gong Yuanjun <ruc_gongyuanjun@163.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
`rctime' has been a pain point in cephfs due to its buggy
nature - inconsistent values reported and those sorts.
Fixing rctime is non-trivial needing an overall redesign
of the entire nested statistics infrastructure.
As a workaround, PR
http://github.com/ceph/ceph/pull/37938
allows this extended attribute to be manually set. This allows
users to "fixup" inconsistent rctime values. While this sounds
messy, its probably the wisest approach allowing users/scripts
to workaround buggy rctime values.
The above PR enables Ceph MDS to allow manually setting
rctime extended attribute with the corresponding user-land
changes. We may as well allow the same to be done via kclient
for parity.
A non-zero return value from pfkey_broadcast() does not necessarily mean
an error occurred as this function returns -ESRCH when no registered
listener received the message. In particular, a call with
BROADCAST_PROMISC_ONLY flag and null one_sk argument can never return
zero so that this commit in fact prevents processing any PF_KEY message.
One visible effect is that racoon daemon fails to find encryption
algorithms like aes and refuses to start.
Excluding -ESRCH return value would fix this but it's not obvious that
we really want to bail out here and most other callers of
pfkey_broadcast() also ignore the return value. Also, as pointed out by
Steffen Klassert, PF_KEY is kind of deprecated and newer userspace code
should use netlink instead so that we should only disturb the code for
really important fixes.
v2: add a comment explaining why is the return value ignored
Generally, the md_unregister_thread is called with reconfig_mutex, but
raid_message in dm-raid doesn't hold reconfig_mutex to unregister thread,
so md_unregister_thread can be called simulitaneously from two call sites
in theory.
Then after previous commit which remove the protection of reconfig_mutex
for md_unregister_thread completely, the potential issue could be worse
than before.
Let's take pers_lock at the beginning of function to ensure reentrancy.
Reported-by: Donald Buczek <buczek@molgen.mpg.de> Signed-off-by: Guoqing Jiang <guoqing.jiang@linux.dev> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously the protection of kernfs_pr_cont_buf was piggy backed by
rename_lock, which means that pr_cont() needs to be protected under
rename_lock. This can cause potential circular lock dependencies.
If there is an OOM, we have the following call hierarchy:
pr_cont_kernfs_name() will grab rename_lock and call printk. So we have
the following lock dependencies:
kernfs_rename_lock -> console_sem
Sometimes, printk does a wakeup before releasing console_sem, which has
the dependence chain:
console_sem -> p->pi_lock -> rq->lock
Now, imagine one wants to read cgroup_name under rq->lock, for example,
printing cgroup_name in a tracepoint in the scheduler code. They will
be holding rq->lock and take rename_lock:
rq->lock -> kernfs_rename_lock
Now they will deadlock.
A prevention to this circular lock dependency is to separate the
protection of pr_cont_buf from rename_lock. In principle, rename_lock
is to protect the integrity of cgroup name when copying to buf. Once
pr_cont_buf has got its content, rename_lock can be dropped. So it's
safe to drop rename_lock after kernfs_name_locked (and
kernfs_path_from_node_locked) and rely on a dedicated pr_cont_lock
to protect pr_cont_buf.
__msm_console_write() assumes that interrupts are disabled, but
with threaded console printers it is possible that the write()
callback of the console is called with interrupts enabled.
Explicitly disable interrupts using local_irq_save() to preserve
the assumed context.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Signed-off-by: John Ogness <john.ogness@linutronix.de> Link: https://lore.kernel.org/r/20220506213324.470461-1-john.ogness@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Local variable mac created at:
r871xu_drv_init+0x1771/0x3070 drivers/staging/rtl8712/usb_intf.c:394
usb_probe_interface+0xf19/0x1600 drivers/usb/core/driver.c:396
When a machine sports more than one SP804 timer instance, we only bring
up the first one, since multiple timers of the same kind are not useful
to Linux. As this is intentional behaviour, we should not return an
error message, as we do today:
===============
[ 0.000800] Failed to initialize '/bus@8000000/motherboard-bus@8000000/iofpga-bus@300000000/timer@120000': -22
===============
Replace the -EINVAL return with a debug message and return 0 instead.
Also we do not reach the init function anymore if the DT node is
disabled (as this is now handled by OF_DECLARE), so remove the explicit
check for that case.
This fixes a long standing bogus error when booting ARM's fastmodels.
Currently, someone can invoke the sysfs such as state_show()
intermittently before dev_set_drvdata() is done.
And it can be a cause of kernel Oops because of edev is Null at that time.
So modified the driver registration to after setting drviver data.
rtsx_usb_probe() doesn't call usb_set_intfdata() to null out the
interface pointer when probe fails. This leaves a stale pointer.
Noticed the missing usb_set_intfdata() while debugging an unrelated
invalid DMA mapping problem.
Fix it with a call to usb_set_intfdata(..., NULL).
UDC driver should not touch gadget's driver internals, especially it
should not reset driver->bus. This wasn't harmful so far, but since
commit fc274c1e9973 ("USB: gadget: Add a new bus for gadgets") gadget
subsystem got it's own bus and messing with ->bus triggers the
following NULL pointer dereference:
dwc2 12480000.hsotg: bound driver g_ether
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in: ...
CPU: 0 PID: 620 Comm: modprobe Not tainted 5.18.0-rc5-next-20220504 #11862
Hardware name: Samsung Exynos (Flattened Device Tree)
PC is at module_add_driver+0x44/0xe8
LR is at sysfs_do_create_link_sd+0x84/0xe0
...
Process modprobe (pid: 620, stack limit = 0x(ptrval))
...
module_add_driver from bus_add_driver+0xf4/0x1e4
bus_add_driver from driver_register+0x78/0x10c
driver_register from usb_gadget_register_driver_owner+0x40/0xb4
usb_gadget_register_driver_owner from do_one_initcall+0x44/0x1e0
do_one_initcall from do_init_module+0x44/0x1c8
do_init_module from load_module+0x19b8/0x1b9c
load_module from sys_finit_module+0xdc/0xfc
sys_finit_module from ret_fast_syscall+0x0/0x54
Exception stack(0xf1771fa8 to 0xf1771ff0)
...
dwc2 12480000.hsotg: new device is high-speed
---[ end trace 0000000000000000 ]---
The documentation for the freeze() method says that it "should quiesce
the device so that it doesn't generate IRQs or DMA". The unspoken
consequence of not doing this is that MSIs aimed at non-boot CPUs may
get fully lost if they're sent during the period where the target CPU is
offline.
The current callbacks for USB HCD do not fully quiesce interrupts,
specifically on XHCI. Change to use the full suspend/resume flow for
freeze/thaw to ensure interrupts are fully quiesced. This fixes issues
where USB devices fail to thaw during hibernation because XHCI misses
its interrupt and cannot recover.
We hold oxu->lock in position (1) of thread 1, and use
del_timer_sync() to wait timer to stop, but timer handler
also need oxu->lock in position (2) of thread 2. As a result,
oxu_bus_suspend() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irq(), which could let timer handler to obtain
the needed lock.
We hold sport->port.lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need sport->port.lock in position (2) of thread 2. As a result,
sa1100_set_termios() will block forever.
This patch moves del_timer_sync() before spin_lock_irqsave()
in order to prevent the deadlock.
We hold ieee->beacon_lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need ieee->beacon_lock in position (2) of thread 2.
As a result, rtllib_beacons_stop() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
We hold ieee->beacon_lock in position (1) of thread 1 and use
del_timer_sync() to wait timer to stop, but timer handler
also need ieee->beacon_lock in position (2) of thread 2.
As a result, ieee80211_beacons_stop() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
To be sufficiently out of range for the usercopy test to see the lifetime
mismatch, expand the size of the "bad" buffer, which will let it be
beyond current_stack_pointer regardless of stack growth direction.
Paired with the recent addition of stack depth checking under
CONFIG_HARDENED_USERCOPY=y, this will correctly start tripping again.
kstrdup() is also a memory allocation-related function, it returns NULL
when some memory errors happen. So it is better to check the return
value of it so to catch the memory error in time. Besides, there should
have a kfree() to clear up the allocation if we get a failure later in
this function to prevent memory leak.
Gcc-12 correctly warned about this code using a non-NULL pointer as a
truth value:
drivers/gpu/drm/imx/ipuv3-crtc.c: In function ‘ipu_crtc_disable_planes’:
drivers/gpu/drm/imx/ipuv3-crtc.c:72:21: error: the comparison will always evaluate as ‘true’ for the address of ‘plane’ will never be NULL [-Werror=address]
72 | if (&ipu_crtc->plane[1] && plane == &ipu_crtc->plane[1]->base)
| ^
due to the extraneous '&' address-of operator.
Philipp Zabel points out that The mistake had no adverse effect since
the following condition doesn't actually dereference the NULL pointer,
but the intent of the code was obviously to check for it, not to take
the address of the member.
Every iteration of for_each_child_of_node() decrements
the reference count of the previous node.
When break from a for_each_child_of_node() loop,
we need to explicitly call of_node_put() on the child node when
not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: bbd2190ce96d ("Altera TSE: Add main and header file for Altera Ethernet Driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220607041144.7553-1-linmq006@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
But was eventually revised more thoroughly:
- restrict the check to the only branch where needed, in an
uncommon GRE path that uses header_ops and calls skb_pull.
- test skb_transport_header, which is set along with csum_start
in skb_partial_csum_set in the normal header_ops datapath.
Turns out skbs can arrive in this branch without the transport
header set, e.g., through BPF redirection.
Revise the check back to check csum_start directly, and only if
CHECKSUM_PARTIAL. Do leave the check in the updated location.
Check field regardless of whether TUNNEL_CSUM is configured.
The current design does not arm the tracer if traces are available before
the tracer string database is fully loaded, leading to an unfunctional tracer.
This fix will rearm the tracer every time the FW triggers tracer event
regardless of the tracer strings database status.
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the caller (net/ipv6/seg6.c)
and the callee (net/ipv6/seg6_hmac.c) belong to the same module.
It seems an internal function call in ipv6.ko.
Fixes: bf355b8d2c30 ("ipv6: sr: add core files for SR HMAC support") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
net/ipv4/xfrm4_policy.c is never compiled as modular.
(CONFIG_XFRM is boolean)
Fixes: 2f32b51b609f ("xfrm: Introduce xfrm_input_afinfo to access the the callbacks properly") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Acked-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
EXPORT_SYMBOL and __init is a bad combination because the .init.text
section is freed up after the initialization. Hence, modules cannot
use symbols annotated __init. The access to a freed symbol may end up
with kernel panic.
modpost used to detect it, but it has been broken for a decade.
Recently, I fixed modpost so it started to warn it again, then this
showed up in linux-next builds.
There are two ways to fix it:
- Remove __init
- Remove EXPORT_SYMBOL
I chose the latter for this case because the only in-tree call-site,
drivers/net/phy/phy_device.c is never compiled as modular.
(CONFIG_PHYLIB is boolean)
Fixes: 90eff9096c01 ("net: phy: Allow splitting MDIO bus/device support from PHYs") Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
I found that NFSD's new NFSv3 READDIRPLUS XDR encoder was screwing up
right at the end of the page array. xdr_get_next_encode_buffer() does
not compute the value of xdr->end correctly:
* The check to see if we're on the final available page in xdr->buf
needs to account for the space consumed by @nbytes.
* The new xdr->end value needs to account for the portion of @nbytes
that is to be encoded into the previous buffer.
Fixes: 2825a7f90753 ("nfsd4: allow encoding across page boundaries") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Reviewed-by: NeilBrown <neilb@suse.de> Reviewed-by: J. Bruce Fields <bfields@fieldses.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported an illegal copy_to_user() attempt
from bpf_prog_get_info_by_fd() [1]
There was no repro yet on this bug, but I think
that commit 0aef499f3172 ("mm/usercopy: Detect vmalloc overruns")
is exposing a prior bug in bpf arm64.
bpf_prog_get_info_by_fd() looks at prog->jited_len
to determine if the JIT image can be copied out to user space.
My theory is that syzbot managed to get a prog where prog->jited_len
has been set to 43, while prog->bpf_func has ben cleared.
It is not clear why copy_to_user(uinsns, NULL, ulen) is triggering
this particular warning.
I thought find_vma_area(NULL) would not find a vm_struct.
As we do not hold vmap_area_lock spinlock, it might be possible
that the found vm_struct was garbage.
unix_dgram_poll() calls unix_dgram_peer_wake_me() without `other`'s
lock held and check if its receive queue is full. Here we need to
use unix_recvq_full_lockless() instead of unix_recvq_full(), otherwise
KCSAN will report a data-race.
of_find_device_by_node() takes reference, we should use put_device()
to release it when not need anymore.
Add missing put_device() to avoid refcount leak.
Fixes: 43f01da0f279 ("MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pxa3xx_gcu_probe(), the sequence of error lable is wrong, it will
leads some resource leaked, so adjust the sequence to handle the error
correctly, and if pxa3xx_gcu_add_buffer() fails, pxa3xx_gcu_free_buffers()
need be called.
In pxa3xx_gcu_remove(), add missing clk_disable_unpreprare().
When doing layoutget as part of the open() compound, we have to be
careful to release the layout locks before we can call any further RPC
calls, such as setattr(). The reason is that those calls could trigger
a recall, which could deadlock.
When configuring a nommu classic m68k system enabling the uboot parameter
passing support (CONFIG_UBOOT) will produce the following compile error:
m68k-linux-ld: arch/m68k/kernel/uboot.o: in function `process_uboot_commandline':
uboot.c:(.init.text+0x32): undefined reference to `_init_sp'
The logic to support this option is only used on ColdFire based platforms
(in its head.S startup code). So make the selection of this option
depend on building for a ColdFire based platform.
The non-MMU m68k pagetable ZERO_PAGE() macro is being set to the
somewhat non-sensical value of "virt_to_page(0)". The zeroth page
is not in any way guaranteed to be a page full of "0". So the result
is that ZERO_PAGE() will almost certainly contain random values.
We already allocate a real "empty_zero_page" in the mm setup code shared
between MMU m68k and non-MMU m68k. It is just not hooked up to the
ZERO_PAGE() macro for the non-MMU m68k case.
Fix ZERO_PAGE() to use the allocated "empty_zero_page" pointer.
I am not aware of any specific issues caused by the old code.
Timeout as 1 second sets an upper limit on the length
of the transfer executed, but there is no maximum length
of a write or read message set in i2c_adapter_quirks for
this controller.
This upper limit affects devices that require sending
large firmware blobs over I2C.
To remove that limitation, calculate the minimal time
necessary, plus some wiggle room, for every message and
use it instead of the default one second, if more than
one second.
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com> Acked-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
To prepare for support asynchronous tracer_init_tracefs initcall,
avoid calling create_trace_option_files before __update_tracer_options.
Otherwise, create_trace_option_files will show warning because
some tracers in trace_types list are already in tr->topts.
For example, hwlat_tracer call register_tracer in late_initcall,
and global_trace.dir is already created in tracing_init_dentry,
hwlat_tracer will be put into tr->topts.
Then if the __update_tracer_options is executed after hwlat_tracer
registered, create_trace_option_files find that hwlat_tracer is
already in tr->topts.
When setting bootparams="trace_event=initcall:initcall_start tp_printk=1" in the
cmdline, the output_printk() was called, and the spin_lock_irqsave() was called in the
atomic and irq disable interrupt context suitation. On the PREEMPT_RT kernel,
these locks are replaced with sleepable rt-spinlock, so the stack calltrace will
be triggered.
Fix it by raw_spin_lock_irqsave when PREEMPT_RT and "trace_event=initcall:initcall_start
tp_printk=1" enabled.
The function percent_rmt_hitm_cmp() wrongly uses local HITMs for
sorting remote HITMs.
Since this function is to sort cache lines for remote HITMs, this patch
changes to use 'rmt_hitm' field for correct sorting.
Fixes: 9cb3500afc0980c5 ("perf c2c report: Add hitm/store percent related sort keys") Signed-off-by: Leo Yan <leo.yan@linaro.org> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Joe Mario <jmario@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20220530084253.750190-1-leo.yan@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In AFS, a directory is handled as a file that the client downloads and
parses locally for the purposes of performing lookup and getdents
operations. The in-kernel afs filesystem has a number of functions that
do this.
A directory file is arranged as a series of 2K blocks divided into
32-byte slots, where a directory entry occupies one or more slots, plus
each block starts with one or more metadata blocks.
When parsing a block, if the last slots are occupied by a dirent that
occupies more than a single slot and the file position points at a slot
that's not the initial one, the logic in afs_dir_iterate_block() that
skips over it won't advance the file pointer to the end of it. This
will cause an infinite loop in getdents() as it will keep retrying that
block and failing to advance beyond the final entry.
Fix this by advancing the file pointer if the next entry will be beyond
it when we skip a block.
This was found by the generic/676 xfstest but can also be triggered with
something like:
1) A new passive FastOpen TCP socket is created.
This FO socket waits for an ACK coming from client to be a complete
ESTABLISHED one.
2) A socket operation on this socket goes through lock_sock()
release_sock() dance.
3) While the socket is owned by the user in step 2),
a retransmit of the SYN is received and stored in socket backlog.
4) At release_sock() time, the socket backlog is processed while
in process context.
5) A SYNACK packet is cooked in response of the SYN retransmit.
6) -> tcp_rtx_synack() is called in process context.
Before blamed commit, tcp_rtx_synack() was always called from BH handler,
from a timer handler.
Fix this by using TCP_INC_STATS() & NET_INC_STATS()
which do not assume caller is in non preemptible context.
Some features (LRO, HW GRO) conflict with XDP. If there is an attempt to
enable such features while XDP is active, they will be set to `off
[requested on]`. In order to activate these features after XDP is turned
off, the driver needs to call netdev_update_features(). This commit adds
this missing call after XDP state changes.
Fixes: cf6e34c8c22f ("net/mlx5e: Properly block LRO when XDP is enabled") Fixes: b0617e7b3500 ("net/mlx5e: Properly block HW GRO when XDP is enabled") Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the `-z unique-symbol` linker flag or any similar mechanism,
it is possible to trigger the following:
ERROR: modpost: "param_set_uint.0" [vmlinux] is a static EXPORT_SYMBOL
The reason is that for now the condition from remove_dot():
if (m && (s[n + m] == '.' || s[n + m] == 0))
which was designed to test if it's a dot or a '\0' after the suffix
is never satisfied.
This is due to that `s[n + m]` always points to the last digit of a
numeric suffix, not on the symbol next to it (from a custom debug
print added to modpost):
param_set_uint.0, s[n + m] is '0', s[n + m + 1] is '\0'
So it's off-by-one and was like that since 2014.
Fix this for the sake of any potential upcoming features, but don't
bother stable-backporting, as it's well hidden -- apart from that
LD flag, it can be triggered only with GCC LTO which never landed
upstream.
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
mv88e6xxx_mdio_register() pass the device node to of_mdiobus_register().
We don't need the device node after it.
Add missing of_node_put() to avoid refcount leak.
Fixes: a3c53be55c95 ("net: dsa: mv88e6xxx: Support multiple MDIO busses") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Marek Behún <kabel@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "fsp->location" variable comes from user via ethtool_get_rxnfc().
Check that it is valid to prevent an out of bounds read.
Fixes: 7aab747e5563 ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The argument of scatterwalk_unmap() is supposed to be the void* that was
returned by the previous scatterwalk_map() call.
The s390 AES-GCM implementation was instead passing the pointer to the
struct scatter_walk.
This doesn't actually break anything because scatterwalk_unmap() only uses
its argument under CONFIG_HIGHMEM and ARCH_HAS_FLUSH_ON_KUNMAP.
We can get "failed to disable" clock_unprepare warnings on unbind at least
for the serial console device if the unbind is done before the device has
been idled.
As some devices are using deferred idle, we must check the status for
pending idle work to idle the device.
Add CSIZE sanitization for unsupported CSIZE configurations. In
addition, if parity is asked for but CSx was unsupported, the sensible
result is CS8+parity which requires setting USART_CR1_M0 like with 9
bits.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: c8a9d043947b (serial: stm32: fix word length configuration) Cc: Erwan Le Ray <erwan.leray@st.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220519081808.3776-9-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only CS7 and CS8 seem supported but CSIZE is not sanitized from CS5 or
CS6 to CS8. In addition, ASC_CTL_MODE_7BIT_PAR suggests that CS7 has
to have parity, thus add PARENB.
Incorrect CSIZE results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS7 and CS8 seem supported but CSIZE is not sanitized from
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS7 and CS8 are supported but CSIZE is not sanitized with
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Only CS7 and CS8 seem supported but CSIZE is not sanitized to CS8 in
the default: block.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
SER_RS485_RTS_ON_SEND and SER_RS485_RTS_AFTER_SEND relate to behavior
within RS485 operation. The driver checks if they have the same value
which is not possible to realize with the hardware. The check is taken
regardless of SER_RS485_ENABLED flag and -EINVAL is returned when the
check fails, which creates problems.
This check makes it unnecessarily complicated to turn RS485 mode off as
simple zeroed serial_rs485 struct will trigger that equal values check.
In addition, the driver itself memsets its rs485 structure to zero when
RS485 is disabled but if userspace would try to make an TIOCSRS485
ioctl() call with the very same struct, it would end up failing with
-EINVAL which doesn't make much sense.
Resolve the problem by moving the check inside SER_RS485_ENABLED block.
The uart_ops startup() callback is called without interrupts
disabled and without port->lock locked, relatively late during the
boot process (from the call path of console_on_rootfs()). If the
device is a console, it was already previously registered and could
be actively printing messages.
Since the startup() callback is reading/writing registers used by
the console write() callback (AML_UART_CONTROL), its access must
be synchronized using the port->lock. Currently it is not.
The startup() callback is the only function that explicitly enables
interrupts. Without the synchronization, it is possible that
interrupts become accidentally permanently disabled.
Some implementations of the SBI time extension depend on hart-local
state (for example, CSRs) that are lost or hardware that is powered
down when a CPU is suspended. To be safe, the clockevents driver
cannot assume that timer IRQs will be received during CPU suspend.
Fixes: 62b019436814 ("clocksource: new RISC-V SBI timer driver") Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Anup Patel <anup@brainfault.org> Link: https://lore.kernel.org/r/20220509012121.40031-1-samuel@sholland.org Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_matching_node_and_match returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
The panic notifier infrastructure executes registered callbacks when
a panic event happens - such callbacks are executed in atomic context,
with interrupts and preemption disabled in the running CPU and all other
CPUs disabled. That said, mutexes in such context are not a good idea.
This patch replaces a regular mutex with a mutex_trylock safer approach;
given the nature of the mutex used in the driver, it should be pretty
uncommon being unable to acquire such mutex in the panic path, hence
no functional change should be observed (and if it is, that would be
likely a deadlock with the regular mutex).
Fixes: 2227b7c74634 ("coresight: add support for CPU debug module") Cc: Leo Yan <leo.yan@linaro.org> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20220427224924.592546-10-gpiccoli@igalia.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
The function documentation of usb_set_configuration says that its
callers should hold the device lock. This lock is held for all
callsites except tweak_set_configuration_cmd. The code path can be
executed for example when attaching a remote USB device.
The solution is to surround the call by the device lock.
This bug was found using my experimental own-developed static analysis
tool, which reported the missing lock on v5.17.2. I manually verified
this bug report by doing code review as well. I runtime checked that
the required lock is not held. I compiled and runtime tested this on
x86_64 with a USB mouse. After applying this patch, my analyser no
longer reports this potential bug.
In goldfish_tty_probe(), the port initialized through tty_port_init()
should be destroyed in error paths.In goldfish_tty_remove(), qtty->port
also should be destroyed or else might leak resources.
If the list does not exit early then data == NULL and 'module' does not
point to a valid list element.
Using 'module' in such a case is not valid and was therefore removed.
Fixes: 6dd67645f22c ("greybus: audio: Use single codec driver registration") Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Vaibhav Agarwal <vaibhav.sr@gmail.com> Reviewed-by: Mark Greer <mgreer@animalcreek.com> Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com> Link: https://lore.kernel.org/r/20220321123626.3068639-1-jakobkoschel@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>