The return value of hga_card_detect() is not properly handled causing
the probe to succeed even though hga_card_detect() failed. Since probe
succeeds, hgafb_open() can be called which will end up operating on an
unmapped hga_vram. This results in an out-of-bounds access as reported
by kernel test robot [1].
To fix this, correctly detect failure of hga_card_detect() by checking
for a non-zero error code.
syzbot is reporting OOB write at vga16fb_imageblit() [1], for
resize_screen() from ioctl(VT_RESIZE) returns 0 without checking whether
requested rows/columns fit the amount of memory reserved for the graphical
screen if current mode is KD_GRAPHICS.
Restore the original intent of the VT_RESIZEX ioctl's `v_clin' parameter
which is the number of pixel rows per character (cell) rather than the
height of the font used.
For framebuffer devices the two values are always the same, because the
former is inferred from the latter one. For VGA used as a true text
mode device these two parameters are independent from each other: the
number of pixel rows per character is set in the CRT controller, while
font height is in fact hardwired to 32 pixel rows and fonts of heights
below that value are handled by padding their data with blanks when
loaded to hardware for use by the character generator. One can change
the setting in the CRT controller and it will update the screen contents
accordingly regardless of the font loaded.
The `v_clin' parameter is used by the `vgacon' driver to set the height
of the character cell and then the cursor position within. Make the
parameter explicit then, by defining a new `vc_cell_height' struct
member of `vc_data', set it instead of `vc_font.height' from `v_clin' in
the VT_RESIZEX ioctl, and then use it throughout the `vgacon' driver
except where actual font data is accessed which as noted above is
independent from the CRTC setting.
This way the framebuffer console driver is free to ignore the `v_clin'
parameter as irrelevant, as it always should have, avoiding any issues
attempts to give the parameter a meaning there could have caused, such
as one that has led to commit 988d0763361b ("vt_ioctl: make VT_RESIZEX
behave like VT_RESIZE"):
"syzbot is reporting UAF/OOB read at bit_putcs()/soft_cursor() [1][2],
for vt_resizex() from ioctl(VT_RESIZEX) allows setting font height
larger than actual font height calculated by con_font_set() from
ioctl(PIO_FONT). Since fbcon_set_font() from con_font_set() allocates
minimal amount of memory based on actual font height calculated by
con_font_set(), use of vt_resizex() can cause UAF/OOB read for font
data."
The problem first appeared around Linux 2.5.66 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit 9736a3546de7 ("Merge with Linux 2.5.66."), where VT_RESIZEX
code in `vt_ioctl' was updated as follows:
if (clin)
- video_font_height = clin;
+ vc->vc_font.height = clin;
making the parameter apply to framebuffer devices as well, perhaps due
to the use of "font" in the name of the original `video_font_height'
variable. Use "cell" in the new struct member then to avoid ambiguity.
Fix an issue with VGA console font size changes made after the initial
video text mode has been changed with a user tool like `svgatextmode'
calling the VT_RESIZEX ioctl. As it stands in that case the original
screen geometry continues being used to validate further VT resizing.
Consequently when the video adapter is firstly reprogrammed from the
original say 80x25 text mode using a 9x16 character cell (720x400 pixel
resolution) to say 80x37 text mode and the same character cell (720x592
pixel resolution), and secondly the CRTC character cell updated to 9x8
(by loading a suitable font with the KD_FONT_OP_SET request of the
KDFONTOP ioctl), the VT geometry does not get further updated from 80x37
and only upper half of the screen is used for the VT, with the lower
half showing rubbish corresponding to whatever happens to be there in
the video memory that maps to that part of the screen. Of course the
proportions change according to text mode geometries and font sizes
chosen.
Address the problem then, by updating the text mode geometry defaults
rather than checking against them whenever the VT is resized via a user
ioctl.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: e400b6ec4ede ("vt/vgacon: Check if screen resize request comes from userspace") Cc: stable@vger.kernel.org # v2.6.24+ Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function qlcnic_dl_lb_test() currently calls netdev_alloc_skb()
without checking afterwards that the allocation succeeded. Fix this by
checking if the skb is NULL and returning an error in such a case.
Breaking out of the loop if the skb is NULL is not correct as no error
would be reported to the caller and no message would be printed for the
user.
Check return value of lp5xx_read and if non-zero, jump to code at end of
the function, causing lp5523_stop_all_engines to be executed before
returning the error value up the call chain. This fixes the original
commit (248b57015f35) which was reverted due to the University of Minnesota
problems.
If alloc_workqueue() fails, properly catch this and propagate the error
to the calling functions, so that the devuce initialization will
properly error out.
In case clk_prepare() fails, capture and propagate the error code up the
stack. If regulator_enable() was called earlier, properly unwind it by
calling regulator_disable().
niu_pci_eeprom_read() may fail, so add checks to its return value and
propagate the error up the callstack.
An examination of the callstack up to niu_pci_eeprom_read shows that:
niu_pci_eeprom_read() // returns int
niu_pci_vpd_scan_props() // returns int
niu_pci_vpd_fetch() // returns *void*
niu_get_invariants() // returns int
since niu_pci_vpd_fetch() returns void which breaks the bubbling up,
change its return type to int so that error is propagated upwards.
Signed-off-by: Du Cheng <ducheng2@gmail.com> Cc: Shannon Nelson <shannon.lee.nelson@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-24-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The change here was incorrect. While it is nice to check if
niu_pci_eeprom_read() succeeded or not when using the data, any error
that might have happened was not propagated upwards properly, causing
the kernel to assume that these reads were successful, which results in
invalid data in the buffer that was to contain the successfully read
data.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Shannon Nelson <shannon.lee.nelson@gmail.com> Cc: David S. Miller <davem@davemloft.net> Fixes: 26fd962bde0b ("niu: fix missing checks of niu_pci_eeprom_read") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-23-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit does not properly detect if an error happens because the
logic after this loop will not detect that there was a failed
allocation.
Cc: Aditya Pakki <pakki001@umn.edu> Cc: David S. Miller <davem@davemloft.net> Fixes: 5bf7295fe34a ("qlcnic: Avoid potential NULL pointer dereference") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-25-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This commit is not correct, it should not have used unlikely() and is
not propagating the error properly to the calling function, so it should
be reverted at this point in time. Also, if the check failed, the
work queue was still assumed to be allocated, so further accesses would
have continued to fail, meaning this patch does nothing to solve the
root issues at all.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: Bryan Brattlof <hello@bryanbrattlof.com> Fixes: 765976285a8c ("rtlwifi: fix a potential NULL pointer dereference") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-13-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Peter points out, if we were to disconnect and then reconnect this
driver from a device, the "global" state of the device would contain odd
values and could cause problems. Fix this up by just initializing the
whole thing to 0 at probe() time.
Ideally this would be a per-device variable, but given the age and the
total lack of users of it, that would require a lot of s/./->/g changes
for really no good reason.
Reported-by: Peter Rosin <peda@axentia.se> Cc: Jens Axboe <axboe@kernel.dk> Reviewed-by: Peter Rosin <peda@axentia.se> Link: https://lore.kernel.org/r/YJP2j6AU82MqEY2M@kroah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fields, "toc" and "cd_info", of "struct gdrom_unit gd" are allocated
in "probe_gdrom()". Prevent a memory leak by making sure "gd.cd_info" is
deallocated in the "remove_gdrom()" function.
Also prevent double free of the field "gd.toc" by moving it from the
module's exit function to "remove_gdrom()". This is because, in
"probe_gdrom()", the function makes sure to deallocate "gd.toc" in case
of any errors, so the exit function invoked later would again free
"gd.toc".
The patch also maintains consistency by deallocating the above mentioned
fields in "remove_gdrom()" along with another memory allocated field
"gd.disk".
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
Because of this, all submissions from this group must be reverted from
the kernel tree and will need to be re-reviewed again to determine if
they actually are a valid fix. Until that work is complete, remove this
change to ensure that no problems are being introduced into the
codebase.
Cc: Wenwen Wang <wang6495@umn.edu> Cc: Peter Rosin <peda@axentia.se> Cc: Jens Axboe <axboe@kernel.dk> Fixes: 093c48213ee3 ("gdrom: fix a memory leak bug") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-27-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit log for this change was incorrect, no "error
handling code" was added, things will blow up just as badly as before if
any of these cases ever were true. As this BUG_ON() never fired, and
most of these checks are "obviously" never going to be true, let's just
revert to the original code for now until this gets unwound to be done
correctly in the future.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit here, while technically correct, did not fully
handle all of the reported issues that the commit stated it was fixing,
so revert it until it can be "fixed" fully.
Note, ioremap() probably will never fail for old hardware like this, and
if anyone actually used this hardware (a PowerMac era PCI display card),
they would not be using fbdev anymore.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, it was determined that this commit is not needed at all so
just revert it. Also, the call to lm80_init_client() was not properly
handled, so if error handling is needed in the lm80_probe() function,
then it should be done properly, not half-baked like the commit being
reverted here did.
Cc: Kangjie Lu <kjlu@umn.edu> Fixes: 9aa3aa15f4c2 ("hwmon: (lm80) fix a missing check of bus read in lm80 probe") Cc: stable <stable@vger.kernel.org> Acked-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20210503115736.2104747-5-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit does not properly unwind if there is an error
condition so it needs to be reverted at this point in time.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: Jacek Anaszewski <jacek.anaszewski@gmail.com> Cc: stable <stable@vger.kernel.org> Fixes: 248b57015f35 ("leds: lp5523: fix a missing check of return value of lp55xx_read") Link: https://lore.kernel.org/r/20210503115736.2104747-9-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit causes a memory leak when it is trying to claim it
is properly handling errors. Revert this change and fix it up properly
in a follow-on commit.
Cc: Kangjie Lu <kjlu@umn.edu> Cc: David S. Miller <davem@davemloft.net> Fixes: f86a3b83833e ("net: stmicro: fix a missing check of clk_prepare") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-21-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This patch "looks" correct, but the driver keeps on running and will
fail horribly right afterward if this error condition ever trips.
So points for trying to resolve an issue, but a huge NEGATIVE value for
providing a "fake" fix for the problem as nothing actually got resolved
at all. I'll go fix this up properly...
modprobe brd rd_size=1048576
dmsetup create o --table "0 `blockdev --getsize /dev/ram0` snapshot-origin /dev/ram0"
dmsetup create s --table "0 `blockdev --getsize /dev/ram0` snapshot /dev/ram0 /dev/ram1 N 0"
The reason is that when we test for zero chunk size, we jump to the label
bad_read_metadata without setting the "r" variable. The function
snapshot_ctr destroys all the structures and then exits with "r == 0". The
kernel then crashes because it falsely believes that snapshot_ctr
succeeded.
In order to fix the bug, we set the variable "r" to -EINVAL.
When multiple PCI devices get assigned to a guest right at boot, libxl
incrementally populates the backend tree. The writes for the first of
the devices trigger the backend watch. In turn xen_pcibk_setup_backend()
will set the XenBus state to Initialised, at which point no further
reconfigures would happen unless a device got hotplugged. Arrange for
reconfigure to also get triggered from the backend watch handler.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Cc: stable@vger.kernel.org Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/r/2337cbd6-94b9-4187-9862-c03ea12e0c61@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit message for this change was incorrect as the code
path can never result in a NULL dereference, alluding to the fact that
whatever tool was used to "find this" is broken. It's just an optional
resource reservation, so removing this check is fine.
Cc: Kangjie Lu <kjlu@umn.edu> Acked-by: Takashi Iwai <tiwai@suse.de> Fixes: dcd0feac9bab ("ALSA: sb8: add a check for request_region") Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210503115736.2104747-35-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mackie d.2 has an extension card for IEEE 1394 communication, which uses
BridgeCo DM1000 ASIC. On the other hand, Mackie d.4 Pro has built-in
function for IEEE 1394 communication by Oxford Semiconductor OXFW971,
according to schematic diagram available in Mackie website. Although I
misunderstood that Mackie d.2 Pro would be also a model with OXFW971,
it's wrong. Mackie d.2 Pro is a model which includes the extension card
as factory settings.
This commit fixes entries in Kconfig and comment in ALSA OXFW driver.
Cc: <stable@vger.kernel.org> Fixes: fd6f4b0dc167 ("ALSA: bebob: Add skelton for BeBoB based devices") Fixes: ec4dba5053e1 ("ALSA: oxfw: Add support for Behringer/Mackie devices") Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20210513125652.110249-3-o-takashi@sakamocchi.jp Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
snd_usbmidi_get_ms_info() may access beyond the border when a
malformed descriptor is passed. This patch adds the sanity checks of
the given MS endpoint descriptors, and skips invalid ones.
When using smb2_copychunk_range() for large ranges we will
run through several iterations of a loop calling SMB2_ioctl()
but never actually free the returned buffer except for the final
iteration.
This leads to memory leaks everytime a large copychunk is requested.
Fixes: 9bf0c9cd4314 ("CIFS: Fix SMB2/SMB3 Copy offload support (refcopy) for large files") Cc: <stable@vger.kernel.org> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suppose we have 2 threads, the group-leader L and a sub-theread T,
both parked in ptrace_stop(). Debugger tries to resume both threads
and does
ptrace(PTRACE_CONT, T);
ptrace(PTRACE_CONT, L);
If the sub-thread T execs in between, the 2nd PTRACE_CONT doesn not
resume the old leader L, it resumes the post-exec thread T which was
actually now stopped in PTHREAD_EVENT_EXEC. In this case the
PTHREAD_EVENT_EXEC event is lost, and the tracer can't know that the
tracee changed its pid.
This patch makes ptrace() fail in this case until debugger does wait()
and consumes PTHREAD_EVENT_EXEC which reports old_pid. This affects all
ptrace requests except the "asynchronous" PTRACE_INTERRUPT/KILL.
The patch doesn't add the new PTRACE_ option to not complicate the API,
and I _hope_ this won't cause any noticeable regression:
- If debugger uses PTRACE_O_TRACEEXEC and the thread did an exec
and the tracer does a ptrace request without having consumed
the exec event, it's 100% sure that the thread the ptracer
thinks it is targeting does not exist anymore, or isn't the
same as the one it thinks it is targeting.
- To some degree this patch adds nothing new. In the scenario
above ptrace(L) can fail with -ESRCH if it is called after the
execing sub-thread wakes the leader up and before it "steals"
the leader's pid.
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0aeff ("xhci: Use command structures when queuing commands on the command ring") Cc: <stable@vger.kernel.org> Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com
[iwamatsu: Adjust context] Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Same reasons than for the previous commits : 6289a98f0817 ("sit: proper dev_{hold|put} in ndo_[un]init methods") 40cb881b5aaa ("ip6_vti: proper dev_{hold|put} in ndo_[un]init methods") 7f700334be9a ("ip6_gre: proper dev_{hold|put} in ndo_[un]init methods")
After adopting CONFIG_PCPU_DEV_REFCNT=n option, syzbot was able to trigger
a warning [1]
Issue here is that:
- all dev_put() should be paired with a corresponding prior dev_hold().
- A driver doing a dev_put() in its ndo_uninit() MUST also
do a dev_hold() in its ndo_init(), only when ndo_init()
is returning 0.
Otherwise, register_netdevice() would call ndo_uninit()
in its error path and release a refcount too soon.
Without this change, the DAC ctl's name could be changed only when
the machine has both Speaker and Headphone, but we met some machines
which only has Lineout and Headhpone, and the Lineout and Headphone
share the Audio Mixer0 and DAC0, the ctl's name is set to "Front".
On most of machines, the "Front" is used for Speaker only or Lineout
only, but on this machine it is shared by Lineout and Headphone,
This introduces an issue in the pipewire and pulseaudio, suppose users
want the Headphone to be on and the Speaker/Lineout to be off, they
could turn off the "Front", this works on most of the machines, but on
this machine, the "Front" couldn't be turned off otherwise the
headphone will be off too. Here we do some change to let the ctl's
name change to "Headphone+LO" on this machine, and pipewire and
pulseaudio already could handle "Headphone+LO" and "Speaker+LO".
(https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/747)
Ritesh reported a bug [1] against UML, noting that it crashed on
startup. The backtrace shows the following (heavily redacted):
(gdb) bt
...
#26 0x0000000060015b5d in sem_init () at ipc/sem.c:268
#27 0x00007f89906d92f7 in ?? () from /lib/x86_64-linux-gnu/libcom_err.so.2
#28 0x00007f8990ab8fb2 in call_init (...) at dl-init.c:72
...
#40 0x00007f89909bf3a6 in nss_load_library (...) at nsswitch.c:359
...
#44 0x00007f8990895e35 in _nss_compat_getgrnam_r (...) at nss_compat/compat-grp.c:486
#45 0x00007f8990968b85 in __getgrnam_r [...]
#46 0x00007f89909d6b77 in grantpt [...]
#47 0x00007f8990a9394e in __GI_openpty [...]
#48 0x00000000604a1f65 in openpty_cb (...) at arch/um/os-Linux/sigio.c:407
#49 0x00000000604a58d0 in start_idle_thread (...) at arch/um/os-Linux/skas/process.c:598
#50 0x0000000060004a3d in start_uml () at arch/um/kernel/skas/process.c:45
#51 0x00000000600047b2 in linux_main (...) at arch/um/kernel/um_arch.c:334
#52 0x000000006000574f in main (...) at arch/um/os-Linux/main.c:144
indicating that the UML function openpty_cb() calls openpty(),
which internally calls __getgrnam_r(), which causes the nsswitch
machinery to get started.
This loads, through lots of indirection that I snipped, the
libcom_err.so.2 library, which (in an unknown function, "??")
calls sem_init().
Now, of course it wants to get libpthread's sem_init(), since
it's linked against libpthread. However, the dynamic linker
looks up that symbol against the binary first, and gets the
kernel's sem_init().
Hajime Tazaki noted that "objcopy -L" can localize a symbol,
so the dynamic linker wouldn't do the lookup this way. I tried,
but for some reason that didn't seem to work.
Doing the same thing in the linker script instead does seem to
work, though I cannot entirely explain - it *also* works if I
just add "VERSION { { global: *; }; }" instead, indicating that
something else is happening that I don't really understand. It
may be that explicitly doing that marks them with some kind of
empty version, and that's different from the default.
Explicitly marking them with a version breaks kallsyms, so that
doesn't seem to be possible.
Marking all the symbols as local seems correct, and does seem
to address the issue, so do that. Also do it for static link,
nsswitch libraries could still be loaded there.
[1] https://bugs.debian.org/983379
Reported-by: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-By: Anton Ivanov <anton.ivanov@cambridgegreys.com> Tested-By: Ritesh Raj Sarraf <rrs@debian.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
In enable_slot(), if pci_get_slot() returns NULL, we clear the SLOT_ENABLED
flag. When pci_get_slot() finds a device, it increments the device's
reference count. In this case, we did not call pci_dev_put() to decrement
the reference count, so the memory of the device (struct pci_dev type) will
eventually leak.
Call pci_dev_put() to decrement its reference count when pci_get_slot()
returns a PCI device.
Link: https://lore.kernel.org/r/b411af88-5049-a1c6-83ac-d104a1f429be@huawei.com Signed-off-by: Feilong Lin <linfeilong@huawei.com> Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gcc-11 complains about a prototype declaration that is different
from the function definition:
drivers/isdn/capi/kcapi.c:724:44: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
724 | u16 capi20_get_manufacturer(u32 contr, u8 *buf)
| ~~~~^~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:62:43: note: previously declared as an array ‘u8[64]’ {aka ‘unsigned char[64]’}
62 | u16 capi20_get_manufacturer(u32 contr, u8 buf[CAPI_MANUFACTURER_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/isdn/capi/kcapi.c:790:38: error: argument 2 of type ‘u8 *’ {aka ‘unsigned char *’} declared as a pointer [-Werror=array-parameter=]
790 | u16 capi20_get_serial(u32 contr, u8 *serial)
| ~~~~^~~~~~
In file included from drivers/isdn/capi/kcapi.c:13:
drivers/isdn/capi/kcapi.h:64:37: note: previously declared as an array ‘u8[8]’ {aka ‘unsigned char[8]’}
64 | u16 capi20_get_serial(u32 contr, u8 serial[CAPI_SERIAL_LEN]);
| ~~~^~~~~~~~~~~~~~~~~~~~~~~
Change the definition to make them match.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:2673:9: warning: this 'for' clause does not guard... [-Wmisleading-indentation]
2673 | for (i = 0; i < n; ++i) \
gcc-11 now warns about a confusingly indented code block:
drivers/usb/host/sl811-hcd.c: In function ‘sl811h_hub_control’:
drivers/usb/host/sl811-hcd.c:1291:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
1291 | if (*(u16*)(buf+2)) /* only if wPortChange is interesting */
| ^~
drivers/usb/host/sl811-hcd.c:1295:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
1295 | break;
Rewrite this to use a single if() block with the __is_defined() macro.
gcc-11 starts warning about misleading indentation inside of macros:
drivers/misc/kgdbts.c: In function ‘kgdbts_break_test’:
drivers/misc/kgdbts.c:103:9: error: this ‘if’ clause does not guard... [-Werror=misleading-indentation]
103 | if (verbose > 1) \
| ^~
drivers/misc/kgdbts.c:200:9: note: in expansion of macro ‘v2printk’
200 | v2printk("kgdbts: breakpoint complete\n");
| ^~~~~~~~
drivers/misc/kgdbts.c:105:17: note: ...this statement, but the latter is misleadingly indented as if it were guarded by the ‘if’
105 | touch_nmi_watchdog(); \
| ^~~~~~~~~~~~~~~~~~
The code looks correct to me, so just reindent it for readability.
arch/x86/lib/msr-smp.c:255:51: error: argument 2 of type ‘u32 *’ {aka ‘unsigned int *’} declared as a pointer [-Werror=array-parameter=]
255 | int rdmsr_safe_regs_on_cpu(unsigned int cpu, u32 *regs)
| ~~~~~^~~~
arch/x86/include/asm/msr.h:347:50: note: previously declared as an array ‘u32[8]’ {aka ‘unsigned int[8]’}
syzbot can trigger the WARN() in init_uevent_argv() which isn't the
nicest as the code does properly recover and handle the error. So
change the WARN() call to pr_warn() and provide some more information on
what the buffer size that was needed.
If there are not any dm devices, we need to zero the "dev" argument in
the first structure dm_name_list. However, this can cause out of
bounds write, because the "needed" variable is zero and len may be
less than eight.
Fix this bug by reporting DM_BUFFER_FULL_FLAG if the result buffer is
too small to hold the "nl->dev" value.
The tz->lock must be hold during the looping over the instances in that
thermal zone. This lock was missing in the governor code since the
beginning, so it's hard to point into a particular commit.
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210422153624.6074-2-lukasz.luba@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent versions of the PCI Express specification have deprecated support
for I/O transactions and actually some PCIe host bridges, such as Power
Systems Host Bridge 4 (PHB4), do not implement them.
The default kernel configuration choice for the defxx driver is the use
of I/O ports rather than MMIO for PCI and EISA systems. It may have
made sense as a conservative backwards compatible choice back when MMIO
operation support was added to the driver as a part of TURBOchannel bus
support. However nowadays this configuration choice makes the driver
unusable with systems that do not implement I/O transactions for PCIe.
Make DEFXX_MMIO the configuration default then, except where configured
for EISA. This exception is because an EISA adapter can have its MMIO
decoding disabled with ECU (EISA Configuration Utility) and therefore
not available with the resource allocation infrastructure we implement,
while port I/O is always readily available as it uses slot-specific
addressing, directly mapped to the slot an option card has been placed
in and handled with our EISA bus support core. Conversely a kernel that
supports modern systems which may not have I/O transactions implemented
for PCIe will usually not be expected to handle legacy EISA systems.
The change of the default will make it easier for people, including but
not limited to distribution packagers, to make a working choice for the
driver.
Update the option description accordingly and while at it replace the
potentially ambiguous PIO acronym with IOP for "port I/O" vs "I/O ports"
according to our nomenclature used elsewhere.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: e89a2cfb7d7b ("[TC] defxx: TURBOchannel support") Cc: stable@vger.kernel.org # v2.6.21+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This may happen if the port becomes resume status exactly
when usb_port_resume() gets port status, it still need provide
a TRSMCRY time before access the device.
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcdf6 ("usb: dwc2: gadget: manage ep0 state in software") Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Phil Elwell <phil@raspberrypi.com> Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some devices (specifically the SC8180x based Surface Pro X with
QCOM04A6) HC halt / xhci_halt() times out during boot. Manually binding
the xhci-hcd driver at some point later does not exhibit this behavior.
To work around this, double XHCI_MAX_HALT_USEC, which also resolves this
issue.
'retval' is known to be -ENODEV here.
This is a hard-coded default error code which is not useful in the error
message. Moreover, another error message is printed at the end of the
error handling path. The corresponding error code (-ENOMEM) is more
informative.
So remove simplify the first error message.
While at it, also remove the useless initialization of 'retval'.
Sysbot has reported a "divide error" which has been identified as being
caused by a corrupted file_size value within the file inode. This value
has been corrupted to a much larger value than expected.
Calculate_skip() is passed i_size_read(inode) >> msblk->block_log. Due to
the file_size value corruption this overflows the int argument/variable in
that function, leading to the divide error.
This patch changes the function to use u64. This will accommodate any
unexpectedly large values due to corruption.
The value returned from calculate_skip() is clamped to be never more than
SQUASHFS_CACHED_BLKS - 1, or 7. So file_size corruption does not lead to
an unexpectedly large return result here.
The entry flush mitigation can be enabled/disabled at runtime via a
debugfs file (entry_flush), which causes the kernel to patch itself to
enable/disable the relevant mitigations.
However depending on which mitigation we're using, it may not be safe to
do that patching while other CPUs are active. For example the following
crash:
Shows that we returned to userspace with a corrupted LR that points into
the kernel, due to executing the partially patched call to the fallback
entry flush (ie. we missed the LR restore).
Fix it by doing the patching under stop machine. The CPUs that aren't
doing the patching will be spinning in the core of the stop machine
logic. That is currently sufficient for our purposes, because none of
the patching we do is to that code or anywhere in the vicinity.
We have NR_syscall syscalls from [0 .. NR_syscall-1].
However the check for invalid syscall number is "> NR_syscall" as
opposed to >=. This off-by-one error erronesously allows "NR_syscall"
to be treated as valid syscall causeing out-of-bounds access into
syscall-call table ensuing a crash (holes within syscall table have a
invalid-entry handler but this is beyond the array implementing the
table).
This problem showed up on v5.6 kernel when testing glibc 2.33 (v5.10
kernel capable, includng faccessat2 syscall 439). The v5.6 kernel has
NR_syscalls=439 (0 to 438). Due to the bug, 439 passed by glibc was
not handled as -ENOSYS but processed leading to a crash.
When vzalloc() returns NULL to sha_regions, no error return code of
kexec_calculate_store_digests() is assigned. To fix this bug, ret is
assigned with -ENOMEM in this case.
Link: https://lkml.kernel.org/r/20210309083904.24321-1-baijiaju1990@gmail.com Fixes: a43cac0d9dc2 ("kexec: split kexec_file syscall code to kexec_file.c") Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Acked-by: Baoquan He <bhe@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing rmap_item from stable tree, STABLE_FLAG of rmap_item is
cleared with head reserved. So the following scenario might happen: For
ksm page with rmap_item1:
cmp_and_merge_page
stable_node->head = &migrate_nodes;
remove_rmap_item_from_tree, but head still equal to stable_node;
try_to_merge_with_ksm_page failed;
return;
For the same ksm page with rmap_item2, stable node migration succeed this
time. The stable_node->head does not equal to migrate_nodes now. For ksm
page with rmap_item1 again:
We would miss the rmap_item for stable_node and might result in failed
rmap_walk_ksm(). Fix this by set rmap_item->head to NULL when rmap_item
is removed from stable tree.
Link: https://lkml.kernel.org/r/20210330140228.45635-5-linmiaohe@huawei.com Fixes: 4146d2d673e8 ("ksm: make !merge_across_nodes migration safe") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
An out of bounds write happens when setting the default power state.
KASAN sees this as:
[drm] radeon: 512M of GTT memory ready.
[drm] GART: num cpu pages 131072, num gpu pages 131072
==================================================================
BUG: KASAN: slab-out-of-bounds in
radeon_atombios_parse_power_table_1_3+0x1837/0x1998 [radeon]
Write of size 4 at addr ffff88810178d858 by task systemd-udevd/157
Without KASAN, this will manifest later when the kernel attempts to
allocate memory that was stomped, since it collides with the inline slab
freelist pointer:
Normally SCTP_MIB_CURRESTAB is always incremented once asoc enter into
ESTABLISHED from the state < ESTABLISHED and decremented when the asoc
is being deleted.
However, in sctp_sf_do_dupcook_b(), the asoc's state can be changed to
ESTABLISHED from the state >= ESTABLISHED where it shouldn't increment
SCTP_MIB_CURRESTAB. Otherwise, one asoc may increment MIB_CURRESTAB
multiple times but only decrement once at the end.
I was able to reproduce it by using scapy to do the 4-way shakehands,
after that I replayed the COOKIE-ECHO chunk with 'peer_vtag' field
changed to different values, and SCTP_MIB_CURRESTAB was incremented
multiple times and never went back to 0 even when the asoc was freed.
This patch is to fix it by only incrementing SCTP_MIB_CURRESTAB when
the state < ESTABLISHED in sctp_sf_do_dupcook_b().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the client ignores the value of the sr_eof of the SEEK
operation. According to the spec, if the server didn't find the
requested extent and reached the end of the file, the server
would return sr_eof=true. In case the request for DATA and no
data was found (ie in the middle of the hole), then the lseek
expects that ENXIO would be returned.
We (adam zabrocki, alexander matrosov, alexander tereshkin, maksym
bazalii) observed the check:
if (fh->size > sizeof(struct nfs_fh))
should not use the size of the nfs_fh struct which includes an extra two
bytes from the size field.
struct nfs_fh {
unsigned short size;
unsigned char data[NFS_MAXFHSIZE];
}
but should determine the size from data[NFS_MAXFHSIZE] so the memcpy
will not write 2 bytes beyond destination. The proposed fix is to
compare against the NFS_MAXFHSIZE directly, as is done elsewhere in fs
code base.
Fixes: d67ae825a59d ("pnfs/flexfiles: Add the FlexFile Layout Driver") Signed-off-by: Nikola Livic <nlivic@gmail.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to use unsigned long subtraction and then convert to signed in
order to deal correcly with C overflow rules.
Fixes: f5062003465c ("NFS: Set an attribute barrier on all updates") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pci_scan_device(), if pci_setup_device() fails for any reason, the code
will not release device's of_node by calling pci_release_of_node(). Fix
that by calling the release function.
Fixes: 98d9f30c820d ("pci/of: Match PCI devices to OF nodes dynamically") Link: https://lore.kernel.org/r/20210124232826.1879-1-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The IOMMU table is divided into pools for concurrent mappings and each
pool has a separate spinlock. When taking the ownership of an IOMMU group
to pass through a device to a VM, we lock these spinlocks which triggers
a false negative warning in lockdep (below).
This fixes it by annotating the large pool's spinlock as a nest lock
which makes lockdep not complaining when locking nested locks if
the nest lock is locked already.
===
WARNING: possible recursive locking detected
5.11.0-le_syzkaller_a+fstn1 #100 Not tainted
--------------------------------------------
qemu-system-ppc/4129 is trying to acquire lock: c0000000119bddb0 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
but task is already holding lock: c0000000119bdd30 (&(p->lock)/1){....}-{2:2}, at: iommu_take_ownership+0xac/0x1e0
other info that might help us debug this:
Possible unsafe locking scenario:
Fix the following out-of-bounds warnings by adding a new structure
wl3501_req instead of duplicating the same members in structure
wl3501_join_req and wl3501_scan_confirm:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [39, 108] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 36 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [25, 95] from the object at 'sig' is out of the bounds of referenced subobject 'beacon_period' with type 'short unsigned int' at offset 22 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
bunch of struct members adjacent to each other in a single call to
memcpy(). Now that a new struct wl3501_req enclosing all those adjacent
members is introduced, memcpy() doesn't overrun the length of
&sig.beacon_period and &this->bss_set[i].beacon_period, because the
address of the new struct object _req_ is used as the destination,
instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Fix the following out-of-bounds warnings by enclosing structure members
daddr and saddr into new struct addr, in structures wl3501_md_req and
wl3501_md_ind:
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
arch/x86/include/asm/string_32.h:182:25: warning: '__builtin_memcpy' offset [18, 23] from the object at 'sig' is out of the bounds of referenced subobject 'daddr' with type 'u8[6]' {aka 'unsigned char[6]'} at offset 11 [-Warray-bounds]
The problem is that the original code is trying to copy data into a
couple of arrays adjacent to each other in a single call to memcpy().
Now that a new struct _addr_ enclosing those two adjacent arrays
is introduced, memcpy() doesn't overrun the length of &sig.daddr[0]
and &sig.daddr, because the address of the new struct object _addr_
is used, instead.
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
The ALC3263 codec on the XPS 13 9343 is also found on the Latitude 13 7350
and Venue 11 Pro 7140. They require the same handling for the combo jack to
work with a headset: GPIO pin 6 must be set.
The HDA driver always sets this pin on the ALC3263, which it distinguishes
by the codec vendor/device ID 0x10ec0288 and PCI subsystem vendor ID 0x1028
(Dell). The ASoC driver does not use PCI, so adapt this check to use DMI to
determine if Dell is the system vendor.
net/sctp/sm_make_chunk.c:3150:4: warning: 'memcpy' offset [17, 28] from the object at 'addr' is out of the bounds of referenced subobject 'v4' with type 'struct sockaddr_in' at offset 0 [-Warray-bounds]
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
Link: https://github.com/KSPP/linux/issues/109 Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the user selects the very first entry in a page and performs a
search-up operation, or selects the very last entry in a page and
performs a search-down operation that will not succeed (e.g., via
[/]asdfzzz[Up Arrow]), nconf will never terminate searching the page.
The reason is that in this case, the starting point will be set to -1
or n, which is then translated into (n - 1) (i.e., the last entry of
the page) or 0 (i.e., the first entry of the page) and finally the
search begins. This continues to work fine until the index reaches 0 or
(n - 1), at which point it will be decremented to -1 or incremented to
n, but not checked against the starting point right away. Instead, it's
wrapped around to the bottom or top again, after which the starting
point check occurs... and naturally fails.
My original implementation added another check for -1 before wrapping
the running index variable around, but Masahiro Yamada pointed out that
the actual issue is that the comparison point (starting point) exceeds
bounds (i.e., the [0,n-1] interval) in the first place and that,
instead, the starting point should be fixed.
This has the welcome side-effect of also fixing the case where the
starting point was n while searching down, which also lead to an
infinite loop.
OTOH, this code is now essentially all his work.
Amazingly, nobody seems to have been hit by this for 11 years - or at
the very least nobody bothered to debug and fix this.
selftests/bpf/Makefile includes lib.mk. With the following command
make -j60 LLVM=1 LLVM_IAS=1 <=== compile kernel
make -j60 -C tools/testing/selftests/bpf LLVM=1 LLVM_IAS=1 V=1
some files are still compiled with gcc. This patch
fixed lib.mk issue which sets CC to gcc in all cases.
After channel switch, we should consider any beacon with a
CSA IE as a new switch. If the CSA IE is a leftover from
before the switch that the AP forgot to remove, we'll get
a CSA-to-Self.
This caused issues in iwlwifi where the firmware saw a beacon
with a CSA-to-Self with mode = 1 on the new channel after a
switch. The firmware considered this a new switch and closed
its queues. Since the beacon didn't change between before and
after the switch, we wouldn't handle it (the CRC is the same)
and we wouldn't let the firmware open its queues again or
disconnect if the CSA IE stays for too long.
Clear the CRC valid state after we switch to make sure that
we handle the beacon and handle the CSA IE as required.
syzbot is hitting "INFO: trying to register non-static key." message [1],
for "struct l2cap_chan"->tx_q.lock spinlock is not yet initialized when
l2cap_chan_del() is called due to e.g. timeout.
Since "struct l2cap_chan"->lock mutex is initialized at l2cap_chan_create()
immediately after "struct l2cap_chan" is allocated using kzalloc(), let's
as well initialize "struct l2cap_chan"->{tx_q,srej_q}.lock spinlocks there.
Currently l2cap_chan_set_defaults() reset chan->conf_state to zero.
However, there is a flag CONF_NOT_COMPLETE which is set when
creating the l2cap_chan. It is suggested that the flag should be
cleared when l2cap_chan is ready, but when l2cap_chan_set_defaults()
is called, l2cap_chan is not yet ready. Therefore, we must set this
flag as the default.
Commit eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver. This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.
(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)
Signed-off-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
(struct tipc_link_info)->dest is in network order (__be32), so we must
convert the value to network order before assigning. The problem detected
by sparse:
net/tipc/netlink_compat.c:699:24: warning: incorrect type in assignment (different base types)
net/tipc/netlink_compat.c:699:24: expected restricted __be32 [usertype] dest
net/tipc/netlink_compat.c:699:24: got int
Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes the following message which randomly pops up during
glocktop call:
seq_file: buggy .next function table_seq_next did not update position index
The issue is that seq_read_iter() in fs/seq_file.c also needs an
increment of the index in an non next record case as well which this
patch fixes otherwise seq_read_iter() will print out the above message.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If sctp_destroy_sock is called without sock_net(sk)->sctp.addr_wq_lock
held and sp->do_auto_asconf is true, then an element is removed
from the auto_asconf_splist without any proper locking.
This can happen in the following functions:
1. In sctp_accept, if sctp_sock_migrate fails.
2. In inet_create or inet6_create, if there is a bpf program
attached to BPF_CGROUP_INET_SOCK_CREATE which denies
creation of the sctp socket.
This patch is to fix it by moving the auto_asconf init out of
sctp_init_sock(), by which inet_create()/inet6_create() won't
need to operate it in sctp_destroy_sock() when calling
sk_common_release().
It also makes more sense to do auto_asconf init while binding the
first addr, as auto_asconf actually requires an ANY addr bind,
see it in sctp_addr_wq_timeout_handler().
This addresses CVE-2021-23133.
Fixes: 610236587600 ("bpf: Add new cgroup attach type to enable sock modifications") Reported-by: Or Cohen <orcohen@paloaltonetworks.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPU0 is the thread of sctp_addr_wq_timeout_handler(), and CPU1
is that of sctp_close().
The original issue this commit fixed will be fixed in the next
patch.
Reported-by: syzbot+959223586843e69a2674@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intent with this code was to return negative error codes but instead
it returns positives.
The problem is how type promotion works with ternary operations. These
functions return long, "ret" is an int and "copied" is a u32. The
negative error code is first cast to u32 so it becomes a high positive and
then cast to long where it's still a positive.
We could fix this by declaring "ret" as a ssize_t but let's just get rid
of the ternaries instead.
Link: https://lkml.kernel.org/r/YIE+/cK1tBzSuQPU@mwanda Fixes: 5bf2b19320ec ("kfifo: add example files to the kernel sample directory") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Stefani Seibold <stefani@seibold.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In digital_tg_recv_dep_req, it calls nfc_tm_data_received(..,resp).
If nfc_tm_data_received() failed, the callee will free the resp via
kfree_skb() and return error. But in the exit branch, the resp
will be freed again.
My patch sets resp to NULL if nfc_tm_data_received() failed, to
avoid the double free.
Fixes: 1c7a4c24fbfd9 ("NFC Digital: Add target NFC-DEP support") Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the error check in ath9k_hw_read_revisions() was added, it checked for
-EIO which is what ath9k_regread() in the ath9k_htc driver uses. However,
for plain ath9k, the register read function uses ioread32(), which just
returns -1 on error. So if such a read fails, it still gets passed through
and ends up as a weird mac revision in the log output.
Fix this by changing ath9k_regread() to return -1 on error like ioread32()
does, and fix the error check to look for that instead of -EIO.
Fixes: 2f90c7e5d094 ("ath9k: Check for errors when reading SREV register") Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210326180819.142480-1-toke@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result") Fixes: a6286ee630f6 ("net: Add TI DaVinci EMAC driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
VMCI feature is not supported in conjunction with the vSphere Fault
Tolerance (FT) feature.
VMware Tools can repeatedly try to create a vsock connection. If FT is
enabled the kernel logs is flooded with the following messages:
qp_alloc_hypercall result = -20
Could not attach to queue pair with -20
"qp_alloc_hypercall result = -20" was hidden by commit e8266c4c3307
("VMCI: Stop log spew when qp allocation isn't possible"), but "Could
not attach to queue pair with -20" is still there flooding the log.
Since the error message can be useful in some cases, print it only once.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets") Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
While adding the invalid IRQ check after calling platform_get_irq(),
I managed to overlook that the driver has a complex error path in its
probe() method, thus a simple *return* couldn't be used. Use a proper
*goto* instead!
The pci_bus->bridge reference may no longer be valid after
pci_bus_remove() resulting in passing a bad value to device_unregister()
for the associated bridge device.
Store the host_bridge reference in a separate variable prior to
pci_bus_remove().
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.
Fixes: ba92222ed63a ("i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which
takes *unsigned* IRQ #), causing it to fail with -EINVAL, overriding
an original error code. Stop calling devm_request_irq() with invalid
IRQ #s.