Ilja reported that, simply putting it, nothing was validating that
from_addr_param functions were operating on initialized memory. That is,
the parameter itself was being validated by sctp_walk_params, but it
doesn't check for types and their specific sizes and it could be a 0-length
one, causing from_addr_param to potentially work over the next parameter or
even uninitialized memory.
The fix here is to, in all calls to from_addr_param, check if enough space
is there for the wanted IP address type.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c: In function 'nvkm_control_mthd_pstate_info':
drivers/gpu/drm/nouveau/nvkm/engine/device/ctrl.c:60:35: error: overflow in conversion from 'int' to '__s8' {aka 'signed char'} changes value from '-251' to '5'
The code builds on most architectures, but fails on parisc where ENOSYS
is defined as 251.
Replace the error code with -ENODEV (-19). The actual error code does
not really matter and is not passed to userspace - it just has to be
negative.
Fixes: 7238eca4cf18 ("drm/nouveau: expose pstate selection per-power source in sysfs") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Cc: Ben Skeggs <bskeggs@redhat.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pending timer has been set up in blk_throtl_init(). However, the
timer is not deleted in blk_throtl_exit(). This means that the timer
handler may still be running after freeing the timer, which would
result in a use-after-free.
Fix by calling del_timer_sync() to delete the timer in blk_throtl_exit().
kobject_put() should be used to cleanup the memory associated with the
kobject instead of kobject_del(). See the section "Kobject removal" of
"Documentation/core-api/kobject.rst".
If kobject_init_and_add returns with error, kobject_put() is needed here
to avoid memory leak, because kobject_init_and_add may return error
without freeing the memory associated with the kobject it allocated.
The kobject_put() should be used to cleanup the memory associated with the
kobject instead of kobject_del. See the section "Kobject removal" of
"Documentation/core-api/kobject.rst".
If kobject_init_and_add return with error, kobject_put() is needed here to
avoid memory leak, because kobject_init_and_add may return error without
freeing the memory associated with the kobject it allocated.
In nilfs_##name##_attr_release, kobj->parent should not be referenced
because it is a NULL pointer. The release() method of kobject is always
called in kobject_put(kobj), in the implementation of kobject_put(), the
kobj->parent will be assigned as NULL before call the release() method.
So just use kobj to get the subgroups, which is more efficient and can fix
a NULL pointer reference problem.
Patch series "nilfs2: fix incorrect usage of kobject".
This patchset from Nanyong Sun fixes memory leak issues and a NULL
pointer dereference issue caused by incorrect usage of kboject in nilfs2
sysfs implementation.
If kobject_init_and_add return with error, then the cleanup of kobject
is needed because memory may be allocated in kobject_init_and_add
without freeing.
And the place of cleanup_dev_kobject should use kobject_put to free the
memory associated with the kobject. As the section "Kobject removal" of
"Documentation/core-api/kobject.rst" says, kobject_del() just makes the
kobject "invisible", but it is not cleaned up. And no more cleanup will
do after cleanup_dev_kobject, so kobject_put is needed here.
Currently the CRST parsing relies on the fact that on most of x86 devices
the IRQ mapping is 1:1 with Linux vIRQ. However, it may be not true for
some. Fix this by converting GSI to Linux vIRQ before checking it.
Syzbot reported shift-out-of-bounds bug in profile_init().
The problem was in incorrect prof_shift. Since prof_shift value comes from
userspace we need to clamp this value into [0, BITS_PER_LONG -1]
boundaries.
Second possible shiht-out-of-bounds was found by Tetsuo:
sample_step local variable in read_profile() had "unsigned int" type,
but prof_shift allows to make a BITS_PER_LONG shift. So, to prevent
possible shiht-out-of-bounds sample_step type was changed to
"unsigned long".
Also, "unsigned short int" will be sufficient for storing
[0, BITS_PER_LONG] value, that's why there is no need for
"unsigned long" prof_shift.
Link: https://lkml.kernel.org/r/20210813140022.5011-1-paskripkin@gmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-and-tested-by: syzbot+e68c89a9510c159d9684@syzkaller.appspotmail.com Suggested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keno Fischer reported that when a binray loaded via ld-linux-x the
prctl(PR_SET_MM_MAP) doesn't allow to setup brk value because it lays
before mm:end_data.
This of course prevent criu from restoring such programs. Looking into
how kernel operates with brk/start_brk inside brk() syscall I don't see
any problem if we allow to setup brk/start_brk without checking for
end_data. Even if someone pass some weird address here on a purpose then
the worst possible result will be an unexpected unmapping of existing vma
(own vma, since prctl works with the callers memory) but test for
RLIMIT_DATA is still valid and a user won't be able to gain more memory in
case of expanding VMAs via new values shipped with prctl call.
Link: https://lkml.kernel.org/r/20210121221207.GB2174@grain Fixes: bbdc6076d2e5 ("binfmt_elf: move brk out of mmap when doing direct loader exec") Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com> Reported-by: Keno Fischer <keno@juliacomputing.com> Acked-by: Andrey Vagin <avagin@gmail.com> Tested-by: Andrey Vagin <avagin@gmail.com> Cc: Dmitry Safonov <0x7f454c46@gmail.com> Cc: Kirill Tkhai <ktkhai@virtuozzo.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Cc: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When SCTP handles an INIT chunk, it calls for example:
sctp_sf_do_5_1B_init
sctp_verify_init
sctp_verify_param
sctp_process_init
sctp_process_param
handling of SCTP_PARAM_SET_PRIMARY
sctp_verify_init() wasn't doing proper size validation and neither the
later handling, allowing it to work over the chunk itself, possibly being
uninitialized memory.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In one of the fallbacks that SCTP has for identifying an association for an
incoming packet, it looks for AddIp chunk (from ASCONF) and take a peek.
Thing is, at this stage nothing was validating that the chunk actually had
enough content for that, allowing the peek to happen over uninitialized
memory.
Similar check already exists in actual asconf handling in
sctp_verify_asconf().
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device is runtime PM suspended when we enter suspend and has
a dedicated wake IRQ, we can get the following warning:
WARNING: CPU: 0 PID: 108 at kernel/irq/manage.c:526 enable_irq+0x40/0x94
[ 102.087860] Unbalanced enable for IRQ 147
...
(enable_irq) from [<c06117a8>] (dev_pm_arm_wake_irq+0x4c/0x60)
(dev_pm_arm_wake_irq) from [<c0618360>]
(device_wakeup_arm_wake_irqs+0x58/0x9c)
(device_wakeup_arm_wake_irqs) from [<c0615948>]
(dpm_suspend_noirq+0x10/0x48)
(dpm_suspend_noirq) from [<c01ac7ac>]
(suspend_devices_and_enter+0x30c/0xf14)
(suspend_devices_and_enter) from [<c01adf20>]
(enter_state+0xad4/0xbd8)
(enter_state) from [<c01ad3ec>] (pm_suspend+0x38/0x98)
(pm_suspend) from [<c01ab3e8>] (state_store+0x68/0xc8)
This is because the dedicated wake IRQ for the device may have been
already enabled earlier by dev_pm_enable_wake_irq_check(). Fix the
issue by checking for runtime PM suspended status.
This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. On resume, dmesg will have the warning above.
The reason why I have not run into this issue earlier has been that I
typically run my PM test cases from on a serial console instead over ssh.
Fixes: c84345597558 (PM / wakeirq: Enable dedicated wakeirq for suspend) Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the JIT completely removes things like `reg32 += 0`,
however, the BPF_ALU semantics requires the target register to be
zero-extended in such cases.
Fix by optimizing out only the arithmetic operation, but not the
subsequent zero-extension.
The JIT uses agfi for subtracting constants, but -(-0x80000000) cannot
be represented as a 32-bit signed binary integer. Fix by using algfi in
this particular case.
The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a7a ("net: sh_eth: add support for Renesas SuperH Ethernet") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previous commit 68233c583ab4 removes the qlcnic_rom_lock()
in qlcnic_pinit_from_rom(), but remains its corresponding
unlock function, which is odd. I'm not very sure whether the
lock is missing, or the unlock is redundant. This bug is
suggested by a static analysis tool, please advise.
Fixes: 68233c583ab4 ("qlcnic: updated reset sequence") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
0day bot reports a build error:
ERROR: modpost: "clear_user_page" [drivers/media/v4l2-core/videobuf-dma-sg.ko] undefined!
so export it in arch/arc/ to fix the build error.
In most ARCHes, clear_user_page() is a macro. OTOH, in a few
ARCHes it is a function and needs to be exported.
PowerPC exported it in 2004. It looks like nds32 and nios2
still need to have it exported.
A successful 'init_rs_non_canonical()' call should be balanced by a
corresponding 'free_rs()' call in the error handling path of the probe, as
already done in the remove function.
Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
"PAGESIZE / 512" is the number of ECC chunks.
"ECC_BYTES" is the number of bytes needed to store a single ECC code.
"2" is the space reserved by the bad block marker.
"2 + (PAGESIZE / 512) * ECC_BYTES" should of course be lower or equal
than the total number of OOB bytes, otherwise it won't fit.
The fault happens because kern_addr_valid() dereferences existent but not
present PMD in the high kernel mappings.
Such PMDs are created when free_kernel_image_pages() frees regions larger
than 2Mb. In this case, a part of the freed memory is mapped with PMDs and
the set_memory_np_noalias() -> ... -> __change_page_attr() sequence will
mark the PMD as not present rather than wipe it completely.
Have kern_addr_valid() check whether higher level page table entries are
present before trying to dereference them to fix this issue and to avoid
similar issues in the future.
Stable backporting note:
------------------------
Note that the stable marking is for all active stable branches because
there could be cases where pagetable entries exist but are not valid -
see 9a14aefc1d28 ("x86: cpa, fix lookup_address"), for example. So make
sure to be on the safe side here and use pXY_present() accessors rather
than pXY_none() which could #GP when accessing pages in the direct map.
Also see:
c40a56a7818c ("x86/mm/init: Remove freed kernel image areas from alias mapping")
for more info.
Reported-by: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: David Hildenbrand <david@redhat.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Tested-by: Jiri Olsa <jolsa@redhat.com> Cc: <stable@vger.kernel.org> # 4.4+ Link: https://lkml.kernel.org/r/20210819132717.19358-1-rppt@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
read to 0xffff88814eeb24e0 of 4 bytes by task 25834 on cpu 1:
skb_queue_len include/linux/skbuff.h:1869 [inline]
unix_recvq_full net/unix/af_unix.c:194 [inline]
unix_dgram_poll+0x2bc/0x3e0 net/unix/af_unix.c:2777
sock_poll+0x23e/0x260 net/socket.c:1288
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll fs/eventpoll.c:846 [inline]
ep_send_events fs/eventpoll.c:1683 [inline]
ep_poll fs/eventpoll.c:1798 [inline]
do_epoll_wait+0x6ad/0xf00 fs/eventpoll.c:2226
__do_sys_epoll_wait fs/eventpoll.c:2238 [inline]
__se_sys_epoll_wait fs/eventpoll.c:2233 [inline]
__x64_sys_epoll_wait+0xf6/0x120 fs/eventpoll.c:2233
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0x0000001b -> 0x00000001
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 25834 Comm: syz-executor.1 Tainted: G W 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 86b18aaa2b5b ("skbuff: fix a data race in skb_queue_len()") Cc: Qian Cai <cai@lca.pw> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In tipc_sk_enqueue() we use hardcoded 2 jiffies to extract
socket buffer from generic queue to particular socket.
The 2 jiffies is too short in case there are other high priority
tasks get CPU cycles for multiple jiffies update. As result, no
buffer could be enqueued to particular socket.
To solve this, we switch to use constant timeout 20msecs.
Then, the function will be expired between 2 jiffies (CONFIG_100HZ)
and 20 jiffies (CONFIG_1000HZ).
Fixes: c637c1035534 ("tipc: resolve race problem at unicast message reception") Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Le <hoang.h.le@dektech.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of users have reported that they were not able to get the PHY
to successfully link up, especially after commit c36757eb9dee ("net:
phy: consider AN_RESTART status when reading link status") where we
stopped reading just BMSR, but we also read BMCR to determine the link
status.
Andrius at NetBSD did a wonderful job at debugging the problem
and found out that the MDIO bus clock frequency would be incorrectly set
back to its default value which would prevent the MDIO bus controller
from reading PHY registers properly. Back when we only read BMSR, if we
read all 1s, we could falsely indicate a link status, though in general
there is a cable plugged in, so this went unnoticed. After a second read
of BMCR was added, a wrong read will lead to the inability to determine
a link UP condition which is when it started to be visibly broken, even
if it was long before that.
The fix consists in restoring the value of the MD_CSR register that was
set prior to the MAC reset.
Link: http://gnats.netbsd.org/cgi-bin/query-pr-single.pl?number=53494 Fixes: 90f750a81a29 ("r6040: consolidate MAC reset to its own function") Reported-by: Andrius V <vezhlys@gmail.com> Reported-by: Darek Strugacz <darek.strugacz@op.pl> Tested-by: Darek Strugacz <darek.strugacz@op.pl> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reference count leak issue may take place in an error handling
path. If both conditions of tunnel->version == L2TP_HDR_VER_3 and the
return value of l2tp_v3_ensure_opt_in_linear is nonzero, the function
would directly jump to label invalid, without decrementing the reference
count of the l2tp_session object session increased earlier by
l2tp_tunnel_get_session(). This may result in refcount leaks.
Fix this issue by decrease the reference count before jumping to the
label invalid.
Fixes: 4522a70db7aa ("l2tp: fix reading optional fields of L2TPv3") Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2677d2067731 ("dccp: don't free ccid2_hc_tx_sock ...") fixed
a UAF but reintroduced CVE-2017-6074.
When the sock is cloned, two dccps_hc_tx_ccid will reference to the
same ccid. So one can free the ccid object twice from two socks after
cloning.
This issue was found by "Hadar Manor" as well and assigned with
CVE-2020-16119, which was fixed in Ubuntu's kernel. So here I port
the patch from Ubuntu to fix it.
The patch prevents cloned socks from referencing the same ccid.
Fixes: 2677d2067731410 ("dccp: don't free ccid2_hc_tx_sock ...") Signed-off-by: Zhenpeng Lin <zplin@psu.edu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building dp83640.c on arch/parisc/ produces a build warning for
PAGE0 being redefined. Since the macro is not used in the dp83640
driver, just make it a comment for documentation purposes.
In file included from ../drivers/net/phy/dp83640.c:23:
../drivers/net/phy/dp83640_reg.h:8: warning: "PAGE0" redefined
8 | #define PAGE0 0x0000
from ../drivers/net/phy/dp83640.c:11:
../arch/parisc/include/asm/page.h:187: note: this is the location of the previous definition
187 | #define PAGE0 ((struct zeropage *)__PAGE_OFFSET)
Fixes: cb646e2b02b2 ("ptp: Added a clock driver for the National Semiconductor PHYTER.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Richard Cochran <richard.cochran@omicron.at> Cc: John Stultz <john.stultz@linaro.org> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210913220605.19682-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: cc36a070b590 ("net-caif: add CAIF netdevice") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes kernel is trying to probe Fingerprint MCU (FPMCU) when it
hasn't initialized SPI yet. This can happen because FPMCU is restarted
during system boot and kernel can send message in short window
eg. between sysjump to RW and SPI initialization.
I was debugging some crashes on parisc and I found out that there is a
crash possibility if a function using alloca is interrupted by a signal.
The reason for the crash is that the gcc alloca implementation leaves
garbage in the upper 32 bits of the sp register. This normally doesn't
matter (the upper bits are ignored because the PSW W-bit is clear),
however the signal delivery routine in the kernel uses full 64 bits of sp
and it fails with -EFAULT if the upper 32 bits are not zero.
I created this program that demonstrates the problem:
This is because in cipso_v4_doi_free() there is no check
on 'doi_def->map.std' when 'doi_def->type' equal 1, which
is possibe, since netlbl_cipsov4_add_std() haven't initialize
it before alloc 'doi_def->map.std'.
This patch just add the check to prevent panic happen for similar
cases.
Reported-by: Abaci <abaci@linux.alibaba.com> Signed-off-by: Michael Wang <yun.wang@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bad header can have large length field which can cause OOB.
cptr is the last bytes for read, and the eeprom is parsed
from high to low address. The OOB, triggered by the condition
length > cptr could cause memory error with a read on
negative index.
There are some sanity check around length, but it is not
compared with cptr (the remaining bytes). Here, the
corrupted/bad EEPROM can cause panic.
I was able to reproduce the crash, but I cannot find the
log and the reproducer now. After I applied the patch, the
bug is no longer reproducible.
The check for count appears to be incorrect since a non-zero count
check occurs a couple of statements earlier. Currently the check is
always false and the dev->port->irq != PARPORT_IRQ_NONE part of the
check is never tested and the if statement is dead-code. Fix this
by removing the check on count.
Note that this code is pre-git history, so I can't find a sha for
it.
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Logically dead code") Link: https://lore.kernel.org/r/20210730100710.27405-1-colin.king@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
smb_buf is allocated by small_smb_init_no_tc(), and buf type is
CIFS_SMALL_BUFFER, so we should use cifs_small_buf_release() to
release it in failed path.
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For unexplained reasons, the prescaler register for this device needs to
be cleared (set to 1) while performing a data read or else the command
will hang. This does not appear to affect the real clock rate sent out
on the bus, so I assume it's purely to work around a hardware bug.
During normal operation, the prescaler is already set to 1, so nothing
needs to be done. However, in "initial mode" (which is used for sub-MHz
clock speeds, like the core sets while enumerating cards), it's set to
128 and so we need to reset it during data reads. We currently fail to
do this for long reads.
This has no functional affect on the driver's operation currently
written, as the MMC core always sets a clock above 1MHz before
attempting any long reads. However, the core could conceivably set any
clock speed at any time and the driver should still work, so I think
this fix is worthwhile.
I personally encountered this issue while performing data recovery on an
external chip. My connections had poor signal integrity, so I modified
the core code to reduce the clock speed. Without this change, I saw the
card enumerate but was unable to actually read any data.
Writes don't seem to work in the situation described above even with
this change (and even if the workaround is extended to encompass data
write commands). I was not able to find a way to get them working.
In the gfs2 withdraw sequence, the dlm protocol is unmounted with a call
to lm_unmount. After a withdraw, users are allowed to unmount the
withdrawn file system. But at that point we may still have glocks left
over that we need to free via unmount's call to gfs2_gl_hash_clear.
These glocks may have never been completed because of whatever problem
caused the withdraw (IO errors or whatever).
Before this patch, function gdlm_put_lock would still try to call into
dlm to unlock these leftover glocks, which resulted in dlm returning
-EINVAL because the lock space was abandoned. These glocks were never
freed because there was no mechanism after that to free them.
This patch adds a check to gdlm_put_lock to see if the locking protocol
was inactive (DFL_UNMOUNT flag) and if so, free the glock and not
make the invalid call into dlm.
I could have combined this "if" with the one that follows, related to
leftover glock LVBs, but I felt the code was more readable with its own
if clause.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The variable val is declared without initialization, and its address is
passed to amdgpu_i2c_get_byte(). In this function, the value of val is
accessed in:
DRM_DEBUG("i2c 0x%02x 0x%02x read failed\n",
addr, *val);
Also, when amdgpu_i2c_get_byte() returns, val may remain uninitialized,
but it is accessed in:
val &= ~amdgpu_connector->router.ddc_mux_control_pin;
To fix this possible uninitialized-variable access, initialize val to 0 in
amdgpu_i2c_router_select_ddc_port().
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzbot reported a corrupted list in kobject_add_internal [1]. This
happens when multiple HCI_EV_SYNC_CONN_COMPLETE event packets with
status 0 are sent for the same HCI connection. This causes us to
register the device more than once which corrupts the kset list.
As this is forbidden behavior, we add a check for whether we're
trying to process the same HCI_EV_SYNC_CONN_COMPLETE event multiple
times for one connection. If that's the case, the event is invalid, so
we report an error that the device is misbehaving, and ignore the
packet.
The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.
The alloc_tty_driver failure is handled gracefully in hvsi_init. But
tty_register_driver is not. panic is called if that one fails.
So handle the failure of tty_register_driver gracefully too. This will
keep at least the console functional as it was enabled earlier by
console_initcall in hvsi_console_init. Instead of shooting down the
whole system.
This means, we disable interrupts and restore hvsi_wait back to
poll_for_state().
While alloc_tty_driver failure in rs_init would mean we have much bigger
problem, there is no reason to panic when tty_register_driver fails
there. It can fail for various reasons.
So handle the failure gracefully. Actually handle them both while at it.
This will make at least the console functional as it was enabled earlier
by console_initcall in iss_console_init. Instead of shooting down the
whole system.
We move tty_port_init() after alloc_tty_driver(), so that we don't need
to destroy the port in case the latter function fails.
Cc: Chris Zankel <chris@zankel.net> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: linux-xtensa@linux-xtensa.org Acked-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20210723074317.32690-2-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
In case of a jump label print the real address of the piece of code
where a mismatch was detected. This is right before the system panics,
so there is nothing revealed.
In function 'ip_copy_addrs',
inlined from '__ip_queue_xmit' at net/ipv4/ip_output.c:517:2:
net/ipv4/ip_output.c:449:2: warning: 'memcpy' offset [40, 43] from the object at 'fl' is out of the bounds of referenced subobject 'saddr' with type 'unsigned int' at offset 36 [-Warray-bounds]
449 | memcpy(&iph->saddr, &fl4->saddr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
450 | sizeof(fl4->saddr) + sizeof(fl4->daddr));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The problem is that the original code is trying to copy data into a
couple of struct members adjacent to each other in a single call to
memcpy(). This causes a legitimate compiler warning because memcpy()
overruns the length of &iph->saddr and &fl4->saddr. As these are just
a couple of struct members, fix this by using direct assignments,
instead of memcpy().
This helps with the ongoing efforts to globally enable -Warray-bounds
and get us closer to being able to tighten the FORTIFY_SOURCE routines
on memcpy().
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of 'pixclock',
it may cause divide error.
Fix this by checking whether 'pixclock' is zero first.
The userspace program could pass any values to the driver through
ioctl() interface. if the driver doesn't check the value of 'pixclock',
it may cause divide error because the value of 'lineclock' and
'frameclock' will be zero.
Fix this by checking whether 'pixclock' is zero in kyrofb_check_var().
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of 'pixclock',
it may cause divide error.
Fix this by checking whether 'pixclock' is zero first.
Each test case can have a set of sub-tests, where each sub-test can
run the cBPF/eBPF test snippet with its own data_size and expected
result. Before, the end of the sub-test array was indicated by both
data_size and result being zero. However, most or all of the internal
eBPF tests has a data_size of zero already. When such a test also had
an expected value of zero, the test was never run but reported as
PASS anyway.
Now the test runner always runs the first sub-test, regardless of the
data_size and result values. The sub-test array zero-termination only
applies for any additional sub-tests.
There are other ways fix it of course, but this solution at least
removes the surprise of eBPF tests with a zero result always succeeding.
f_ncm tx timeout can call us with null skb to flush
a pending frame. In this case skb is NULL to begin
with but ceases to be null after dev->wrap() completes.
In such a case in->maxpacket will be read, even though
we've failed to check that 'in' is not NULL.
Though I've never observed this fail in practice,
however the 'flush operation' simply does not make sense with
a null usb IN endpoint - there's nowhere to flush to...
(note that we're the gadget/device, and IN is from the point
of view of the host, so here IN actually means outbound...)
In the smk_access_entry() function, if no matching rule is found
in the rust_list, a negative error code will be used to perform bit
operations with the MAY_ enumeration value. This is semantically
wrong. This patch fixes this issue.
The naming of the regulator is problematic. VCC is usually a supply
voltage whereas these devices have a separate VREF pin.
Secondly, the regulator core might have provided a stub regulator if
a real regulator wasn't provided. That would in turn have failed to
provide a voltage when queried. So reality was that there was no way
to use the internal reference.
In order to avoid breaking any dts out in the wild, make sure to fallback
to the original vcc naming if vref is not available.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reported-by: kernel test robot <lkp@intel.com> Acked-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20210627163244.1090296-9-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Updating the current_state field of struct pci_dev the way it is done
in pci_enable_device_flags() before calling do_pci_enable_device() may
not work. For example, if the given PCI device depends on an ACPI
power resource whose _STA method initially returns 0 ("off"), but the
config space of the PCI device is accessible and the power state
retrieved from the PCI_PM_CTRL register is D0, the current_state
field in the struct pci_dev representing that device will get out of
sync with the power.state of its ACPI companion object and that will
lead to power management issues going forward.
To avoid such issues, make pci_enable_device_flags() call
pci_update_current_state() which takes ACPI device power management
into account, if present, to retrieve the current power state of the
device.
Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't call printk() when CONFIG_PRINTK is not set.
Fixes the following build errors:
or1k-linux-ld: arch/openrisc/kernel/entry.o: in function `_external_irq_handler':
(.text+0x804): undefined reference to `printk'
(.text+0x804): relocation truncated to fit: R_OR1K_INSN_REL_26 against undefined symbol `printk'
Fixes: 9d02a4283e9c ("OpenRISC: Boot code") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Jonas Bonn <jonas@southpole.se> Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Cc: Stafford Horne <shorne@gmail.com> Cc: openrisc@lists.librecores.org Signed-off-by: Stafford Horne <shorne@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pciconfig_read() syscall reads PCI configuration space using
hardware-dependent config accessors.
If the read fails on PCI, most accessors don't return an error; they
pretend the read was successful and got ~0 data from the device, so the
syscall returns success with ~0 data in the buffer.
When the accessor does return an error, pciconfig_read() normally fills the
user's buffer with ~0 and returns an error in errno. But after e4585da22ad0 ("pci syscall.c: Switch to refcounting API"), we don't fill
the buffer with ~0 for the EPERM "user lacks CAP_SYS_ADMIN" error.
Userspace may rely on the ~0 data to detect errors, but after e4585da22ad0,
that would not detect CAP_SYS_ADMIN errors.
Restore the original behaviour of filling the buffer with ~0 when the
CAP_SYS_ADMIN check fails.
The ASMedia ASM1062 SATA controller advertises Max_Payload_Size_Supported
of 512, but in fact it cannot handle incoming TLPs with payload size of
512.
We discovered this issue on PCIe controllers capable of MPS = 512 (Aardvark
and DesignWare), where the issue presents itself as an External Abort.
Bjorn Helgaas says:
Probably ASM1062 reports a Malformed TLP error when it receives a data
payload of 512 bytes, and Aardvark, DesignWare, etc convert this to an
arm64 External Abort. [1]
To avoid this problem, limit the ASM1062 Max Payload Size Supported to 256
bytes, so we set the Max Payload Size of devices that may send TLPs to the
ASM1062 to 256 or less.
The merge_fdt_bootargs() function by definition consumes more than 1024
bytes of stack because it has a 1024 byte command line on the stack,
meaning that we always get a warning when building this file:
arch/arm/boot/compressed/atags_to_fdt.c: In function 'merge_fdt_bootargs':
arch/arm/boot/compressed/atags_to_fdt.c:98:1: warning: the frame size of 1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
However, as this is the decompressor and we know that it has a very shallow
call chain, and we do not actually risk overflowing the kernel stack
at runtime here.
This just shuts up the warning by disabling the warning flag for this
file.
Tested on Nexus 7 2012 builds.
Acked-by: Nicolas Pitre <nico@fluxnic.net> Signed-off-by: David Heidelberg <david@ixit.cz> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: <stable@vger.kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ca6bfcb2f6d9 ("libata: Enable queued TRIM for Samsung SSD 860")
limited the existing ATA_HORKAGE_NO_NCQ_TRIM quirk from "Samsung SSD 8*",
covering all Samsung 800 series SSDs, to only apply to "Samsung SSD 840*"
and "Samsung SSD 850*" series based on information from Samsung.
But there is a large number of users which is still reporting issues
with the Samsung 860 and 870 SSDs combined with Intel, ASmedia or
Marvell SATA controllers and all reporters also report these problems
going away when disabling queued trims.
Note that with AMD SATA controllers users are reporting even worse
issues and only completely disabling NCQ helps there, this will be
addressed in a separate patch.
Fixes: ca6bfcb2f6d9 ("libata: Enable queued TRIM for Samsung SSD 860") BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=203475 Cc: stable@vger.kernel.org Cc: Kate Hsuan <hpa@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20210823095220.30157-1-hdegoede@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As warned by smatch:
drivers/media/usb/uvc/uvc_v4l2.c:911 uvc_ioctl_g_input() error: doing dma on the stack (&i)
drivers/media/usb/uvc/uvc_v4l2.c:943 uvc_ioctl_s_input() error: doing dma on the stack (&i)
those two functions call uvc_query_ctrl passing a pointer to
a data at the DMA stack. those are used to send URBs via
usb_control_msg(). Using DMA stack is not supported and should
not work anymore on modern Linux versions.
When a queue pair is created by the following call, it will not
register the user memory if the page_store is NULL, and the
entry->state will be set to VMCIQPB_CREATED_NO_MEM.
vmci_host_unlocked_ioctl
vmci_host_do_alloc_queuepair
vmci_qp_broker_alloc
qp_broker_alloc
qp_broker_create // set entry->state = VMCIQPB_CREATED_NO_MEM;
When unmapping this queue pair, qp_host_unregister_user_memory() will
be called to unregister the non-existent user memory, which will
result in a null pointer reference. It will also change
VMCIQPB_CREATED_NO_MEM to VMCIQPB_CREATED_MEM, which should not be
present in this operation.
Only when the qp broker has mem, it can unregister the user
memory when unmapping the qp broker.
Only when the qp broker has no mem, it can register the user
memory when mapping the qp broker.
Fixes: 06164d2b72aa ("VMCI: queue pairs implementation.") Cc: stable <stable@vger.kernel.org> Reported-by: Hulk Robot <hulkci@huawei.com> Reviewed-by: Jorgen Hansen <jhansen@vmware.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Link: https://lore.kernel.org/r/20210818124845.488312-1-wanghai38@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reading status register can fail in the interrupt handler. In such
case, the regmap_read() will not store anything useful under passed
'val' variable and random stack value will be used to determine type of
interrupt.
Handle the regmap_read() failure to avoid handling interrupt type and
triggering changed power supply event based on random stack value.
Fixes: 39e7213edc4f ("max17042_battery: Support regmap to access device's registers") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xen PV guests are specifying the highest used PFN via the max_pfn
field in shared_info. This value is used by the Xen tools when saving
or migrating the guest.
Unfortunately this field is misnamed, as in reality it is specifying
the number of pages (including any memory holes) of the guest, so it
is the highest used PFN + 1. Renaming isn't possible, as this is a
public Xen hypervisor interface which needs to be kept stable.
The kernel will set the value correctly initially at boot time, but
when adding more pages (e.g. due to memory hotplug or ballooning) a
real PFN number is stored in max_pfn. This is done when expanding the
p2m array, and the PFN stored there is even possibly wrong, as it
should be the last possible PFN of the just added P2M frame, and not
one which led to the P2M expansion.
Fix that by setting shared_info->max_pfn to the last possible PFN + 1.
Fixes: 98dd166ea3a3c3 ("x86/xen/p2m: hint at the last populated P2M entry") Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Link: https://lore.kernel.org/r/20210730092622.9973-2-jgross@suse.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When running as Xen PV guest, masking MSI-X is a responsibility of the
hypervisor. The guest has no write access to the relevant BAR at all - when
it tries to, it results in a crash like this:
BUG: unable to handle page fault for address: ffffc9004069100c
#PF: supervisor write access in kernel mode
#PF: error_code(0x0003) - permissions violation
RIP: e030:__pci_enable_msix_range.part.0+0x26b/0x5f0
e1000e_set_interrupt_capability+0xbf/0xd0 [e1000e]
e1000_probe+0x41f/0xdb0 [e1000e]
local_pci_probe+0x42/0x80
(...)
The recently introduced function msix_mask_all() does not check the global
variable pci_msi_ignore_mask which is set by XEN PV to bypass the masking
of MSI[-X] interrupts.
Add the check to make this function XEN PV compatible.
Fixes: 7d5ec3d36123 ("PCI/MSI: Mask all unused MSI-X entries") Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210826170342.135172-1-marmarek@invisiblethingslab.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MSR_IA32_TSC_ADJUST is written by guest due to TSC ADJUST feature
especially there's a big tsc warp (like a new vCPU is hot-added into VM
which has been up for a long time), tsc_offset is added by a large value
then go back to guest. This causes system time jump as tsc_timestamp is
not adjusted in the meantime and pvclock monotonic character.
To fix this, just notify kvm to update vCPU's guest time before back to
guest.
Cc: stable@vger.kernel.org Signed-off-by: Zelin Deng <zelin.deng@linux.alibaba.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1619576521-81399-2-git-send-email-zelin.deng@linux.alibaba.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ops->receive_buf() may be accessed concurrently from these two
functions. If the driver flushes data to the line discipline
receive_buf() method while tiocsti() is waiting for the
ops->receive_buf() to finish its work, the data race will happen.
Even after commit 6457378fe796 ("ipv4: use siphash instead of Jenkins in
fnhe_hashfun()"), an attacker can still use brute force to learn
some secrets from a victim linux host.
One way to defeat these attacks is to make the max depth of the hash
table bucket a random value.
Before this patch, each bucket of the hash table used to store exceptions
could contain 6 items under attack.
After the patch, each bucket would contains a random number of items,
between 6 and 10. The attacker can no longer infer secrets.
This is slightly increasing memory size used by the hash table,
by 50% in average, we do not expect this to be a problem.
This patch is more complex than the prior one (IPv6 equivalent),
because IPv4 was reusing the oldest entry.
Since we need to be able to evict more than one entry per
update_or_create_fnhe() call, I had to replace
fnhe_oldest() with fnhe_remove_oldest().
Also note that we will queue extra kfree_rcu() calls under stress,
which hopefully wont be a too big issue.
Fixes: 4895c771c7f0 ("ipv4: Add FIB nexthop exceptions.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Keyu Man <kman001@ucr.edu> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Reviewed-by: David Ahern <dsahern@kernel.org> Tested-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
kmemleak reported that dev_name() of internally-handled cores were leaked
on driver unbinding. Let's use device_initialize() to take refcounts for
them and put_device() to properly free the related stuff.
While looking at it, there's another potential issue for those which should
be *registered* into driver core. If device_register() failed, we put
device once and freed bcma_device structures. In bcma_unregister_cores(),
they're treated as unregistered and we hit both UAF and double-free. That
smells not good and has also been fixed now.
Fixes: ab54bc8460b5 ("bcma: fill core details for every device") Signed-off-by: Zenghui Yu <yuzenghui@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210727025232.663-2-yuzenghui@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This error path is unlikely because of it checked for NULL and
returned -ENOMEM earlier in the function. But it should return
an error code here as well if we ever do hit it because of a
race condition or something.
Fixes: bdcd81707973 ("Add ath6kl cleaned up driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20210813113438.GB30697@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
ehci_orion_drv_probe() did not account for possible errors of
clk_prepare_enable() that in particular could cause invocation of
clk_disable_unprepare() on clocks that were not prepared/enabled yet,
e.g. in remove or on handling errors of usb_add_hcd() in probe. Though,
there were several patches fixing different issues with clocks in this
driver, they did not solve this problem.
Add handling of errors of clk_prepare_enable() in ehci_orion_drv_probe()
to avoid calls of clk_disable_unprepare() without previous successful
invocation of clk_prepare_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 8c869edaee07 ("ARM: Orion: EHCI: Add support for enabling clocks") Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Evgeny Novikov <novikov@ispras.ru> Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com> Link: https://lore.kernel.org/r/20210825170902.11234-1-novikov@ispras.ru Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: ce38815d39ea ("I2C: mediatek: Add driver for MediaTek I2C controller") Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru> Reviewed-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated.
Also, the strnlen() call does not avoid the read overflow in the strlcpy
function when a not NUL-terminated string is passed.
So, replace this block by a call to kstrndup() that avoids this type of
overflow and does the same.
Fixes: 066ce6899484d ("cifs: rename cifs_strlcpy_to_host and make it use new functions") Signed-off-by: Len Baker <len.baker@gmx.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For moxart, this is probably not currently an issue but is still good to
fix though.
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver") Cc: Jonas Jensen <jonas.jensen@gmail.com> Cc: Vinod Koul <vkoul@kernel.org> Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210810081644.19353-3-tony@atomide.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Depending on the DMA driver being used, the struct dma_slave_config may
need to be initialized to zero for the unused data.
For example, we have three DMA drivers using src_port_window_size and
dst_port_window_size. If these are left uninitialized, it can cause DMA
failures.
For dw_mmc, this is probably not currently an issue but is still good to
fix though.
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec97853f ("i2c-s3c2410: Change IRQ to be plain integer.") Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log