When backporting 33b8aad21ac1 ("selftests: netfilter: add a
vrf+conntrack testcase") to this stable branch, the executable bits were
not properly set on the
tools/testing/selftests/netfilter/conntrack_vrf.sh file due to quilt not
honoring them.
This commit adds BPF verifier selftests that cover all corner cases by
packet boundary checks. Specifically, 8-byte packet reads are tested at
the beginning of data and at the beginning of data_meta, using all kinds
of boundary checks (all comparison operators: <, >, <=, >=; both
permutations of operands: data + length compared to end, end compared to
data + length). For each case there are three tests:
1. Length is just enough for an 8-byte read. Length is either 7 or 8,
depending on the comparison.
2. Length is increased by 1 - should still pass the verifier. These
cases are useful, because they failed before commit 2fa7d94afc1a
("bpf: Fix the off-by-two error in range markings").
3. Length is decreased by 1 - should be rejected by the verifier.
Some existing tests are just renamed to avoid duplication.
The driver refuses to probe with -EINVAL since the commit 5d9814df0aec
("clocksource/drivers/dw_apb_timer_of: Add error handling if no clock
available").
Before the driver used to probe successfully if either "clock-freq" or
"clock-frequency" properties has been specified in the device tree.
That commit changed
if (A && B)
panic("No clock nor clock-frequency property");
into
if (!A && !B)
return 0;
That's a bug: the reverse of `A && B` is '!A || !B', not '!A && !B'
Signed-off-by: Vadim V. Vlasov <vadim.vlasov@elpitech.ru> Signed-off-by: Alexey Sheplyakov <asheplyakov@basealt.ru> Fixes: 5d9814df0aec56a6 ("clocksource/drivers/dw_apb_timer_of: Add error handling if no clock available"). Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Dinh Nguyen <dinguyen@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vadim V. Vlasov <vadim.vlasov@elpitech.ru> Acked-by: Dinh Nguyen <dinguyen@kernel.org> Link: https://lore.kernel.org/r/20211109153401.157491-1-asheplyakov@basealt.ru Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The buffer list is sorted and this is not being considered while
calculating packet size. This would lead to improper copy length
calculation for non-dmaheap buffers which would eventually cause
sending improper buffers to DSP.
Fixes: c68cfb718c8f ("misc: fastrpc: Add support for context Invoke method") Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by: Jeya R <jeyr@codeaurora.org> Link: https://lore.kernel.org/r/1637771481-4299-1-git-send-email-jeyr@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to ARM(v7M) ARM Interrupt Priority Offsets located at
0xE000E400-0xE000E5EC, while 0xE000E300-0xE000E33C covers read-only
Interrupt Active Bit Registers
Fixes: 292ec080491d ("irqchip: Add support for ARMv7-M NVIC") Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20211201110259.84857-1-vladimir.murzin@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.
Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.
Signed-off-by: Wudi Wang <wangwudi@hisilicon.com> Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Fixes: cc2d3216f53c ("irqchip: GICv3: ITS command queue") Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.
For whatever reason, some devices like QCA6390, WCN6855 using ath11k
are not in M3 state during PM resume, but still functional. The
mhi_pm_resume should then not fail in those cases, and let the higher
level device specific stack continue resuming process.
Add an API mhi_pm_resume_force(), to force resuming irrespective of the
current MHI state. This fixes a regression with non functional ath11k WiFi
after suspend/resume cycle on some machines.
Link: https://lore.kernel.org/regressions/871r5p0x2u.fsf@codeaurora.org/ Fixes: 020d3b26c07a ("bus: mhi: Early MHI resume failure in non M3 state") Cc: stable@vger.kernel.org #5.13 Reported-by: Kalle Valo <kvalo@codeaurora.org> Reported-by: Pengyu Ma <mapengyu@gmail.com> Tested-by: Kalle Valo <kvalo@kernel.org> Acked-by: Kalle Valo <kvalo@kernel.org> Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[mani: Switched to API, added bug report, reported-by tags and CCed stable] Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20211209131633.4168-1-manivannan.sadhasivam@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Foxconn T99W175 device(sdx55 platform) in some host platform,
it would be unavailable once the host execute the err handler.
After checking, it's caused by the delay time too short to
get a successful reset.
Please see my test evidence as bewlow(BTW, I add some extra test logs
in function mhi_pci_reset_prepare and mhi_pci_reset_done):
When MHI_POST_RESET_DELAY_MS equals to 500ms:
Nov 4 14:30:03 jbd-ThinkEdge kernel: [ 146.222477] mhi mhi0: Device MHI is not in valid state
Nov 4 14:30:03 jbd-ThinkEdge kernel: [ 146.222628] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare reset
Nov 4 14:30:03 jbd-ThinkEdge kernel: [ 146.222631] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare mhi_soc_reset
Nov 4 14:30:03 jbd-ThinkEdge kernel: [ 146.222632] mhi mhi0: mhi_soc_reset write soc to reset
Nov 4 14:30:05 jbd-ThinkEdge kernel: [ 147.839993] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_done
Nov 4 14:30:05 jbd-ThinkEdge kernel: [ 147.902063] mhi-pci-generic 0000:2d:00.0: reset failed
When MHI_POST_RESET_DELAY_MS equals to 1000ms or 1500ms:
Nov 4 19:07:26 jbd-ThinkEdge kernel: [ 157.067857] mhi mhi0: Device MHI is not in valid state
Nov 4 19:07:26 jbd-ThinkEdge kernel: [ 157.068029] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare reset
Nov 4 19:07:26 jbd-ThinkEdge kernel: [ 157.068032] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare mhi_soc_reset
Nov 4 19:07:26 jbd-ThinkEdge kernel: [ 157.068034] mhi mhi0: mhi_soc_reset write soc to reset
Nov 4 19:07:29 jbd-ThinkEdge kernel: [ 159.607006] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_done
Nov 4 19:07:29 jbd-ThinkEdge kernel: [ 159.607152] mhi mhi0: Requested to power ON
Nov 4 19:07:51 jbd-ThinkEdge kernel: [ 181.302872] mhi mhi0: Failed to reset MHI due to syserr state
Nov 4 19:07:51 jbd-ThinkEdge kernel: [ 181.303011] mhi-pci-generic 0000:2d:00.0: failed to power up MHI controller
When MHI_POST_RESET_DELAY_MS equals to 2000ms:
Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180527] mhi mhi0: Failed to transition from PM state: Linkdown or Error Fatal Detect to: SYS ERROR Process
Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180535] mhi mhi0: Device MHI is not in valid state
Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180722] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare reset
Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180725] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_prepare mhi_soc_reset
Nov 4 17:51:08 jbd-ThinkEdge kernel: [ 147.180727] mhi mhi0: mhi_soc_reset write soc to reset
Nov 4 17:51:11 jbd-ThinkEdge kernel: [ 150.230787] mhi-pci-generic 0000:2d:00.0: mhi_pci_reset_done
Nov 4 17:51:11 jbd-ThinkEdge kernel: [ 150.230928] mhi mhi0: Requested to power ON
Nov 4 17:51:11 jbd-ThinkEdge kernel: [ 150.231173] mhi mhi0: Power on setup success
Nov 4 17:51:14 jbd-ThinkEdge kernel: [ 153.254747] mhi mhi0: Wait for device to enter SBL or Mission mode
I also tried big data like 3000, and it worked as well. 500ms may not be
enough for all support mhi device. We shall increase it to 2000ms
at least.
Commit fd307a4ad332 ("nvmem: prepare basics for FRAM support") added
support for FRAM devices such as the Cypress FM25V. During testing, it
was found that the FRAM detects properly, however reads and writes fail.
Upon further investigation, two problem were found in at25_probe() routine.
1) In the case of an FRAM device without platform data, eg.
fram == true && spi->dev.platform_data == NULL
the stack local variable "struct spi_eeprom chip" is not initialized
fully, prior to being copied into at25->chip. The chip.flags field in
particular can cause problems.
2) The byte_len of FRAM is computed from its ID register, and is stored
into the stack local "struct spi_eeprom chip" structure. This happens
after the same structure has been copied into at25->chip. As a result,
at25->chip.byte_len does not contain the correct length of the device.
In turn this can cause checks at beginning of at25_ee_read() to fail
(or equally, it could allow reads beyond the end of the device length).
Fix both of these issues by eliminating the on-stack struct spi_eeprom.
Instead use the one inside at25_data structure, which starts of zeroed.
Fixes: fd307a4ad332 ("nvmem: prepare basics for FRAM support") Cc: stable <stable@vger.kernel.org> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> Link: https://lore.kernel.org/r/20211108181627.645638-1-ralph.siemsen@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 5b4258f6721f ("misc: rtsx: rts5249 support runtime PM"), when the
rtsx controller is runtime suspended, bring CPUs offline and back online, the
runtime resume of the controller will fail:
[ 47.319391] smpboot: CPU 1 is now offline
[ 47.414140] x86: Booting SMP configuration:
[ 47.414147] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 47.571334] smpboot: CPU 2 is now offline
[ 47.686055] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 47.808174] smpboot: CPU 3 is now offline
[ 47.878146] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 48.003679] smpboot: CPU 4 is now offline
[ 48.086187] smpboot: Booting Node 0 Processor 4 APIC 0x1
[ 48.239627] smpboot: CPU 5 is now offline
[ 48.326059] smpboot: Booting Node 0 Processor 5 APIC 0x3
[ 48.472193] smpboot: CPU 6 is now offline
[ 48.574181] smpboot: Booting Node 0 Processor 6 APIC 0x5
[ 48.743375] smpboot: CPU 7 is now offline
[ 48.838047] smpboot: Booting Node 0 Processor 7 APIC 0x7
[ 48.965447] __common_interrupt: 1.35 No irq handler for vector
[ 51.174065] mmc0: error -110 doing runtime resume
[ 54.978088] I/O error, dev mmcblk0, sector 21479 op 0x1:(WRITE) flags 0x0 phys_seg 11 prio class 0
[ 54.978108] Buffer I/O error on dev mmcblk0p1, logical block 19431, lost async page write
[ 54.978129] Buffer I/O error on dev mmcblk0p1, logical block 19432, lost async page write
[ 54.978134] Buffer I/O error on dev mmcblk0p1, logical block 19433, lost async page write
[ 54.978137] Buffer I/O error on dev mmcblk0p1, logical block 19434, lost async page write
[ 54.978141] Buffer I/O error on dev mmcblk0p1, logical block 19435, lost async page write
[ 54.978145] Buffer I/O error on dev mmcblk0p1, logical block 19436, lost async page write
[ 54.978148] Buffer I/O error on dev mmcblk0p1, logical block 19437, lost async page write
[ 54.978152] Buffer I/O error on dev mmcblk0p1, logical block 19438, lost async page write
[ 54.978155] Buffer I/O error on dev mmcblk0p1, logical block 19439, lost async page write
[ 54.978160] Buffer I/O error on dev mmcblk0p1, logical block 19440, lost async page write
[ 54.978244] mmc0: card aaaa removed
[ 54.978452] FAT-fs (mmcblk0p1): FAT read failed (blocknr 4257)
There's interrupt immediately raised on rtsx_pci_write_register() in
runtime resume routine, but the IRQ handler hasn't registered yet.
So we can either move rtsx_pci_write_register() after rtsx_pci_acquire_irq(),
or just stop mangling IRQ on runtime PM. Choose the latter to save some
CPU cycles.
When ACPI type is ACPI_SMO8500, the data->dready_trig will not be set, the
memory allocated by iio_triggered_buffer_setup() will not be freed, and cause
memory leak as follows:
Fix it by remove data->dready_trig condition in probe and remove.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: a25691c1f967 ("iio: accel: kxcjk1013: allow using an external trigger") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: <Stable@vger.kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20211025124159.2700301-1-yangyingliang@huawei.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The ad7768-1 driver neglects to call iio_trigger_notify_done() when there
is an error reading the converter data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Both the charging and discharging currents on AXP22x are stored as
12-bit integers, in accordance with the datasheet.
It's also confirmed by vendor BSP (axp20x_adc.c:axp22_icharge_to_mA).
The scale factor of 0.5 is never mentioned in datasheet, nor in the
vendor source code. I think it was here to compensate for
erroneous addition bit in register width.
Tested on custom A40i+AXP221s board with external ammeter as
a reference.
Fixes: 0e34d5de961d ("iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs") Signed-off-by: Evgeny Boger <boger@wirenboard.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Link: https://lore.kernel.org/r/20211116213746.264378-1-boger@wirenboard.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some I/Os are connected to ADC input channels, when the corresponding bit
in PCSEL register are set on STM32H7 and STM32MP15. This is done in the
prepare routine of stm32-adc driver.
There are constraints here, as PCSEL shouldn't be set when VDDA supply
is disabled. Enabling/disabling of VDDA supply in done via stm32-adc-core
runtime PM routines (before/after ADC is enabled/disabled).
Currently, PCSEL remains set when disabling ADC. Later on, PM runtime
can disable the VDDA supply. This creates some conditions on I/Os that
can start to leak current.
So PCSEL needs to be cleared when disabling the ADC.
Fixes: 95e339b6e85d ("iio: adc: stm32: add support for STM32H7") Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com> Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com> Link: https://lore.kernel.org/r/1634905169-23762-1-git-send-email-fabrice.gasnier@foss.st.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Registering a trigger can fail and the return value of
devm_iio_trigger_register() must be checked. Otherwise undefined behavior
can occur when the trigger is used.
Fixes: 7c0299e879dd ("iio: adc: Add support for DLN2 ADC") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Link: https://lore.kernel.org/r/20211101133043.6974-1-lars@metafoo.de Cc: <stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The itg3200 driver neglects to call iio_trigger_notify_done() when there is
an error reading the gyro data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The kxsd9 interrupt handler returns an error code if reading the data
registers fails. In addition when exiting due to an error the trigger
handler does not call `iio_trigger_notify_done()`. Which when not done
keeps the triggered disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Since we can't return the error code make sure to at least log it as part
of the error message.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The ltr501 interrupt handler gets this right for most error paths, but
there is one case where it returns the error code.
In addition for this particular case the trigger handler does not call
`iio_trigger_notify_done()`. Which when not done keeps the triggered
disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
The mma8452 driver directly assigns a trigger to the struct iio_dev. The
IIO core when done using this trigger will call `iio_trigger_put()` to drop
the reference count by 1.
Without the matching `iio_trigger_get()` in the driver the reference count
can reach 0 too early, the trigger gets freed while still in use and a
use-after-free occurs.
Fix this by getting a reference to the trigger before assigning it to the
IIO device.
Fixes: ae6d9ce05691 ("iio: mma8452: Add support for interrupt driven triggers.") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Link: https://lore.kernel.org/r/20211024092700.6844-1-lars@metafoo.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In viio_trigger_alloc() device_initialize() is used to set the initial
reference count of the trigger to 1. Then another get_device() is called on
trigger. This sets the reference count to 2 before the trigger is returned.
iio_trigger_free(), which is the matching API to viio_trigger_alloc(),
calls put_device() which decreases the reference count by 1. But the second
reference count acquired in viio_trigger_alloc() is never dropped.
As a result the iio_trigger_release() function is never called and the
memory associated with the trigger is never freed.
Since there is no reason for the trigger to start its lifetime with two
reference counts just remove the extra get_device() in
viio_trigger_alloc().
Fixes: 5f9c035cae18 ("staging:iio:triggers. Add a reference get to the core for triggers.") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20211024092700.6844-2-lars@metafoo.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
The checks performed by commit aed9d65ac327 ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.
Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors") Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com> Link: https://lore.kernel.org/r/20211210085219.16796-1-pavel.hofman@ivitera.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On sc7180-trogdor class devices with 'fw_devlink=permissive' and KASAN
enabled, you'll see a Use-After-Free reported at bootup.
The root of the problem is that dwc3_qcom_of_register_core() is adding
a devm-allocated "tx-fifo-resize" property to its device tree node
using of_add_property().
The issue is that of_add_property() makes a _permanent_ addition to
the device tree that lasts until reboot. That means allocating memory
for the property using "devm" managed memory is a terrible idea since
that memory will be freed upon probe deferral or device unbinding.
Let's revert the patch since the system is still functional without
it. The fact that of_add_property() makes a permanent change is extra
fodder for those folks who were aruging that the device tree isn't
really the right way to pass information between parts of the
driver. It is an exercise left to the reader to submit a patch
re-adding the new feature in a way that makes everyone happier.
Fixes: cefdd52fa045 ("usb: dwc3: dwc3-qcom: Enable tx-fifo-resize property by default") Cc: stable <stable@vger.kernel.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20211207094327.1.Ie3cde3443039342e2963262a4c3ac36dc2c08b30@changeid Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under some conditions, USB gadget devices can show allocated buffer
contents to a host. Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed. If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
Currently rp_filter tests in fib_tests.sh:fib_rp_filter_test() are
failing. ping sockets are bound to dummy1 using the "-I" option
(SO_BINDTODEVICE), but socket lookup is failing when receiving ping
replies, since the routing table thinks they belong to dummy0.
For example, suppose ping is using a SOCK_RAW socket for ICMP messages.
When receiving ping replies, in __raw_v4_lookup(), sk->sk_bound_dev_if
is 3 (dummy1), but dif (skb_rtable(skb)->rt_iif) says 2 (dummy0), so the
raw_sk_bound_dev_eq() check fails. Similar things happen in
ping_lookup() for SOCK_DGRAM sockets.
These tests used to pass due to a bug [1] in iputils, where "ping -I"
actually did not bind ICMP message sockets to device. The bug has been
fixed by iputils commit f455fee41c07 ("ping: also bind the ICMP socket
to the specific device") in 2016, which is why our rp_filter tests
started to fail. See [2] .
Fixing the tests while keeping everything in one netns turns out to be
nontrivial. Rework the tests and build the following topology:
Consider sending an ICMP_ECHO packet A in ns2. Both source and
destination IP addresses are 192.0.2.1, and we use strict mode rp_filter
in both ns1 and ns2:
1. A is routed to lo since its destination IP address is one of ns2's
local addresses (veth2);
2. A is redirected from lo's egress to veth2's egress using mirred;
3. A arrives at veth1's ingress in ns1;
4. A is redirected from veth1's ingress to lo's ingress, again, using
mirred;
5. In __fib_validate_source(), fib_info_nh_uses_dev() returns false,
since A was received on lo, but reverse path lookup says veth1;
6. However A is not dropped since we have relaxed this check for lo in
commit 66f8209547cc ("fib: relax source validation check for loopback
packets");
Making sure A is not dropped here in this corner case is the whole point
of having this test.
7. As A reaches the ICMP layer, an ICMP_ECHOREPLY packet, B, is
generated;
8. Similarly, B is redirected from lo's egress to veth1's egress (in
ns1), then redirected once again from veth2's ingress to lo's
ingress (in ns2), using mirred.
Also test "ping 127.0.0.1" from ns2. It does not trigger the relaxed
check in __fib_validate_source(), but just to make sure the topology
works with loopback addresses.
Reported-by: Hangbin Liu <liuhangbin@gmail.com> Fixes: adb701d6cfa4 ("selftests: add a test case for rp_filter") Reviewed-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20211201004720.6357-1-yepeilin.cs@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ql_wait_for_drvr_lock() fails and returns false, then this
function should return an error code instead of returning success.
The other problem is that the success path prints an error message
netdev_err(ndev, "Releasing driver lock\n"); Delete that and
re-order the code a little to make it more clear.
Fixes: 5a4faa873782 ("[PATCH] qla3xxx NIC driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211207082416.GA16110@kili Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).
After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.
The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.
Fixes: ed63f1dcd578 (net: fec: clear receive interrupts before processing a packet) Cc: Russell King <rmk+kernel@arm.linux.org.uk> Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com> Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two error paths which accidentally return success instead of
a negative error code.
Fixes: bbd2190ce96d ("Altera TSE: Add main and header file for Altera Ethernet Driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, due to the sequential use of min_t() and clamp_t() macros,
in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is not set, the logic
sets tx_max to 0. This is then used to allocate the data area of the
SKB requested later in cdc_ncm_fill_tx_frame().
This does not cause an issue presently because when memory is
allocated during initialisation phase of SKB creation, more memory
(512b) is allocated than is required for the SKB headers alone (320b),
leaving some space (512b - 320b = 192b) for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
By overriding the max value with the default CDC_NCM_NTB_MAX_SIZE_TX
when not offered through the system provided params, we ensure enough
data space is allocated to handle the CDC data, meaning no crash will
occur.
Cc: Oliver Neukum <oliver@neukum.org> Fixes: 289507d3364f9 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning") Signed-off-by: Lee Jones <lee.jones@linaro.org> Reviewed-by: Bjørn Mork <bjorn@mork.no> Link: https://lore.kernel.org/r/20211202143437.1411410-1-lee.jones@linaro.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 66dfdff03d196e51 ("perf tools: Add Python 3 support") we don't use
the tools/build/feature/test-libpython-version.c version in any Makefile
feature check:
$ find tools/ -type f | xargs grep feature-libpython-version
$
The only place where this was used was removed in 66dfdff03d196e51:
And nowadays we either build with PYTHON=python3 or just install the
python3 devel packages and perf will build against it.
But the leftover feature-libpython-version check made the fast path
feature detection to break in all cases except when python2 devel files
were installed:
As python3 is the norm these days, fix this by just removing the unused
feature-libpython-version feature check, making the test-all fast path
to work with the common case.
This binding was already documented in phy.txt, commit 252ae5330daa
("Documentation: devicetree: Add PHY no lane swap binding"), but got
accidently removed during YAML conversion in commit d8704342c109
("dt-bindings: net: Add a YAML schemas for the generic PHY options").
Note: 'enet-phy-lane-no-swap' and the absence of 'enet-phy-lane-swap' are
not identical, as the former one disable this feature, while the latter
one doesn't change anything.
Fixes: d8704342c109 ("dt-bindings: net: Add a YAML schemas for the generic PHY options") Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20211130082756.713919-1-alexander.stein@ew.tq-group.com Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial implementation of migrate_disable() for mainline was a
wrapper around preempt_disable(). RT kernels substituted this with
a real migrate disable implementation.
Later on mainline gained true migrate disable support, but the
documentation was not updated.
Update the documentation, remove the claims about migrate_disable()
mapping to preempt_disable() on non-PREEMPT_RT kernels.
Fixes: 74d862b682f51 ("sched: Make migrate_disable/enable() independent of RT") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20211127163200.10466-2-bigeasy@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
The HW interrupt gets disabled after S3/S4/reset so we don't receive
notifications for HPD or AUX from DMUB - leading to timeout and
black screen with (or without) DPIA links connected.
[How]
Re-enable the interrupt after S3/S4/reset like we do for the other
DC interrupts.
Guard both instances of the outbox interrupt enable or we'll hang
during restore on ASIC that don't support it.
Fixes: 6eff272dbee7ad ("drm/amd/display: Fix DPIA outbox timeout after GPU reset") Reviewed-by: Jude Shih <Jude.Shih@amd.com> Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
239edf686c14 ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated
bridge") added support for the Type 1 Expansion ROM BAR at config offset
0x38, based on the register being listed in the Marvell Armada A3720 spec.
But the spec doesn't document it at all for RC mode, and there is no ROM in
the SOC, so remove this emulation for now.
The PCI bridge which represents aardvark's PCIe Root Port has an Expansion
ROM Base Address register at offset 0x30, but its meaning is different than
PCI's Expansion ROM BAR register, although the layout is the same. (This
is why we thought it does the same thing.)
First: there is no ROM (or part of BootROM) in the A3720 SOC dedicated for
PCIe Root Port (or controller in RC mode) containing executable code that
would initialize the Root Port, suitable for execution in bootloader (this
is how Expansion ROM BAR is used on x86).
Second: in A3720 spec the register (address 0xD0070030) is not documented
at all for Root Complex mode, but similar to other BAR registers, it has an
"entangled partner" in register 0xD0075920, which does address translation
for the BAR in 0xD0070030:
- the BAR register sets the address from the view of PCIe bus
- the translation register sets the address from the view of the CPU
The other BAR registers also have this entangled partner, and they can be
used to:
- in RC mode: address-checking on the receive side of the RC (they can
define address ranges for memory accesses from remote Endpoints to the
RC)
- in Endpoint mode: allow the remote CPU to access memory on A3720
The Expansion ROM BAR has only the Endpoint part documented, but from the
similarities we think that it can also be used in RC mode in that way.
So either Expansion ROM BAR has different meaning (if the hypothesis above
is true), or we don't know it's meaning (since it is not documented for RC
mode).
Remove the register from the emulated bridge accessing functions.
[bhelgaas: summarize reason for removal (first paragraph)] Fixes: 239edf686c14 ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge") Link: https://lore.kernel.org/r/20211125160148.26029-3-kabel@kernel.org Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Pali Rohár <pali@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When trying to dump VFs VSI RX/TX descriptors
using debugfs there was a crash
due to NULL pointer dereference in i40e_dbg_dump_desc.
Added a check to i40e_dbg_dump_desc that checks if
VSI type is correct for dumping RX/TX descriptors.
When a sock is added to a sock map we evaluate what proto op hooks need to
be used. However, when the program is removed from the sock map we have not
been evaluating if that changes the required program layout.
Before the patch listed in the 'fixes' tag this was not causing failures
because the base program set handles all cases. Specifically, the case with
a stream parser and the case with out a stream parser are both handled. With
the fix below we identified a race when running with a proto op that attempts
to read skbs off both the stream parser and the skb->receive_queue. Namely,
that a race existed where when the stream parser is empty checking the
skb->receive_queue from recvmsg at the precies moment when the parser is
paused and the receive_queue is not empty could result in skipping the stream
parser. This may break a RX policy depending on the parser to run.
The fix tag then loads a specific proto ops that resolved this race. But, we
missed removing that proto ops recv hook when the sock is removed from the
sockmap. The result is the stream parser is stopped so no more skbs will be
aggregated there, but the hook and BPF program continues to be attached on
the psock. User space will then get an EBUSY when trying to read the socket
because the recvmsg() handler is now waiting on a stopped stream parser.
To fix we rerun the proto ops init() function which will look at the new set
of progs attached to the psock and rest the proto ops hook to the correct
handlers. And in the above case where we remove the sock from the sock map
the RX prog will no longer be listed so the proto ops is removed.
Fixes: c5d2177a72a16 ("bpf, sockmap: Fix race in ingress receive verdict with redirect to self") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20211119181418.353932-3-john.fastabend@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
The FSMC NAND controller should apply a delay after the
instruction has been issued on the bus.
The FSMC NAND controller driver did not handle this delay.
Add this waiting delay in the FSMC NAND controller driver.
After setting pre-set combined to 16 queues and reserving 16 queues by
tc qdisc, pre-set maximum combined queues returned to default value
after VF reset being 4 and this generated errors during removing tc.
Fixed by removing clear num_req_queues before reset VF.
Fixes: e284fc280473 (i40e: Add and delete cloud filter) Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Bindushree P <Bindushree.p@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix failed operation code appearing if handling messages from VF.
Implemented by waiting for VF appropriate state if request starts
handle while VF reset.
Without this patch the message handling request while VF is in
a reset state ends with error -5 (I40E_ERR_PARAM).
Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface") Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com> Signed-off-by: Karen Sornek <karen.sornek@intel.com> Tested-by: Tony Brelinski <tony.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the event that the bootloader has configured the Trion PLL as source
for the display clocks, e.g. for the continuous splashscreen, then there
will also be RCGs that are clocked by this instance.
Reconfiguring, and in particular disabling the output of, the PLL will
cause issues for these downstream RCGs and has been shown to prevent
them from being re-parented.
Follow downstream and skip configuration if it's determined that the PLL
is already running.
Fixes: 59128c20a6a9 ("clk: qcom: clk-alpha-pll: Add support for controlling Lucid PLLs") Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Reviewed-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20211123162508.153711-1-bjorn.andersson@linaro.org Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503f3 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Acked-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If hns_roce_cmd_mbox() detects that the hardware is being reset during the
execution of the hns_roce_cmd_mbox(), the driver will not be able to get
the return value from the hardware (the firmware cannot respond to the
driver's mailbox during the hardware reset phase).
The driver needs to wait for the hardware reset to complete before
continuing to execute hns_roce_qp_destroy(), otherwise it may happen that
the driver releases the resources but the hardware is still accessing. In
order to fix this problem, HNS RoCE needs to add a piece of code to wait
for the hardware reset to complete.
The original interface get_hw_reset_stat() is the instantaneous state of
the hardware reset, which cannot accurately reflect whether the hardware
reset is completed, so it needs to be replaced with the ae_dev_reset_cnt
interface.
The sign that the hardware reset is complete is that the return value of
the ae_dev_reset_cnt interface is greater than the original value
reset_cnt recorded by the driver.
Fixes: 6a04aed6afae ("RDMA/hns: Fix the chip hanging caused by sending mailbox&CMQ during reset") Link: https://lore.kernel.org/r/20211123142402.26936-1-liangwenpeng@huawei.com Signed-off-by: Yangyang Li <liyangyang20@huawei.com> Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
is_reset is used to indicate whether the hardware starts to reset. When
hns_roce_hw_v2_reset_notify_down() is called, the hardware has not yet
started to reset. If is_reset is set at this time, all mailbox operations
of resource destroy actions will be intercepted by driver. When the driver
cleans up resources, but the hardware is still accessed, the following
errors will appear:
Currently each channel is added as list to dai channel list, however
there is danger of adding same channel to multiple dai channel list
which endups corrupting the other list where its already added.
This patch ensures that the channel is actually free before adding to
the dai channel list and also ensures that the channel is on the list
before deleting it.
This check was missing previously, and we did not hit this issue as
we were testing very simple usecases with sequence of amixer commands.
wsa881x_set_port() and wsa881x_put_pa_gain() currently returns zero eventhough
it changes the value. Fix this, so that change notifications are sent
correctly.
Move the declaration of temporary arrays to somewhere that won't go out
of scope before the devm_clk_hw_register() call, lest we be at the whim
of the compiler for whether those stack variables get overwritten.
Fixes a crash seen with gcc version 11.2.1 20210728 (Red Hat 11.2.1-1)
Fixes: edbd24ea1e5c ("ASoC: rt5682: Drop usage of __clk_get_name()") Signed-off-by: Rob Clark <robdclark@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20211118010453.843286-1-robdclark@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although it is unlikely that stack could transmit a non LSO
skb with length > MTU, however in some cases or environment such
occurrences actually resulted into firmware asserts due to packet
length being greater than the max supported by the device (~9700B).
This patch adds the safeguard for such odd cases to avoid firmware
asserts.
v2: Added "Fixes" tag with one of the initial driver commit
which enabled the TX traffic actually (as this was probably
day1 issue which was discovered recently by some customer
environment)
Olivia Mackintosh has posted to alsa-devel reporting that
there's a potential bug that could break mixer quirks for Pioneer
devices introduced by 6d27788160362a7ee6c0d317636fe4b1ddbe59a7
"ALSA: usb-audio: Add support for the Pioneer DJM 750MK2
Mixer/Soundcard".
This happened because the DJM 750 MK2 was added last to the Pioneer DJM
device table index and defined as 0x4 but was added to snd_djm_devices[]
just after the DJM 750 (MK1) entry instead of last, after the DJM 900
NXS2. This escaped review.
To prevent that from ever happening again, Takashi Iwai suggested to use
C99 array designators in snd_djm_devices[] instead of simply reordering
the entries.
According to ZBC and SPC specifications, the unit of ALLOCATION LENGTH
field of REPORT ZONES command is byte. However, current scsi_debug
implementation handles it as number of zones to calculate buffer size to
report zones. When the ALLOCATION LENGTH has a large number, this results
in too large buffer size and causes memory allocation failure. Fix the
failure by handling ALLOCATION LENGTH as byte unit.
Link: https://lore.kernel.org/r/20211207010638.124280-1-shinichiro.kawasaki@wdc.com Fixes: f0d1cf9378bd ("scsi: scsi_debug: Add ZBC zone commands") Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20211201041627.1592487-1-ipylypiv@google.com Fixes: 05c6c029a44d ("scsi: pm80xx: Increase number of supported queues") Reviewed-by: Vishakha Channapattan <vishakhavc@google.com> Acked-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Igor Pylypiv <ipylypiv@google.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
do_each_pid_thread(PIDTYPE_PGID) can race with a concurrent
change_pid(PIDTYPE_PGID) that can move the task from one hlist
to another while iterating. Serialize ioprio_get to take
the tasklist_lock in this case, just like it's set counterpart.
Maxime points out that the polling code in mpc_i2c_isr should use the
_atomic API because it is called in an irq context and that the
behaviour of the MCF bit is that it is 1 when the byte transfer is
complete. All of this means the original code was effectively a
udelay(100).
Fix this by using readb_poll_timeout_atomic() and removing the negation
of the break condition.
Fixes: 4a8ac5e45cda ("i2c: mpc: Poll for MCF") Reported-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Tested-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As people have been asking to allow non-root processes to have access to
the tracefs directory, it was considered best to only allow groups to have
access to the directory, where it is easier to just set the tracefs file
system to a specific group (as other would be too dangerous), and that way
the admins could pick which processes would have access to tracefs.
Unfortunately, this broke tooling on Android that expected the other bit
to be set. For some special cases, for non-root tools to trace the system,
tracefs would be mounted and change the permissions of the top level
directory which gave access to all running tasks permission to the
tracing directory. Even though this would be dangerous to do in a
production environment, for testing environments this can be useful.
Now with the new changes to not allow other (which is still the proper
thing to do), it breaks the testing tooling. Now more code needs to be
loaded on the system to change ownership of the tracing directory.
The real solution is to have tracefs honor the gid=xxx option when
mounting. That is,
(tracing group tracing has value 1003)
mount -t tracefs -o gid=1003 tracefs /sys/kernel/tracing
should have it that all files in the tracing directory should be of the
given group.
Copy the logic from d_walk() from dcache.c and simplify it for the mount
case of tracefs if gid is set. All the files in tracefs will be walked and
their group will be set to the value passed in.
Link: https://lkml.kernel.org/r/20211207171729.2a54e1b3@gandalf.local.home Cc: Ingo Molnar <mingo@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: linux-fsdevel@vger.kernel.org Cc: Al Viro <viro@ZenIV.linux.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reported-by: Kalesh Singh <kaleshsingh@google.com> Reported-by: Yabin Cui <yabinc@google.com> Fixes: 49d67e445742 ("tracefs: Have tracefs directories not set OTH permission bits by default") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
signalfd_poll() and binder_poll() are special in that they use a
waitqueue whose lifetime is the current task, rather than the struct
file as is normally the case. This is okay for blocking polls, since a
blocking poll occurs within one task; however, non-blocking polls
require another solution. This solution is for the queue to be cleared
before it is freed, by sending a POLLFREE notification to all waiters.
Unfortunately, only eventpoll handles POLLFREE. A second type of
non-blocking poll, aio poll, was added in kernel v4.18, and it doesn't
handle POLLFREE. This allows a use-after-free to occur if a signalfd or
binder fd is polled with aio poll, and the waitqueue gets freed.
Fix this by making aio poll handle POLLFREE.
A patch by Ramji Jiyani <ramjiyani@google.com>
(https://lore.kernel.org/r/20211027011834.2497484-1-ramjiyani@google.com)
tried to do this by making aio_poll_wake() always complete the request
inline if POLLFREE is seen. However, that solution had two bugs.
First, it introduced a deadlock, as it unconditionally locked the aio
context while holding the waitqueue lock, which inverts the normal
locking order. Second, it didn't consider that POLLFREE notifications
are missed while the request has been temporarily de-queued.
The second problem was solved by my previous patch. This patch then
properly fixes the use-after-free by handling POLLFREE in a
deadlock-free way. It does this by taking advantage of the fact that
freeing of the waitqueue is RCU-delayed, similar to what eventpoll does.
Currently, aio_poll_wake() will always remove the poll request from the
waitqueue. Then, if aio_poll_complete_work() sees that none of the
polled events are ready and the request isn't cancelled, it re-adds the
request to the waitqueue. (This can easily happen when polling a file
that doesn't pass an event mask when waking up its waitqueue.)
This is fundamentally broken for two reasons:
1. If a wakeup occurs between vfs_poll() and the request being
re-added to the waitqueue, it will be missed because the request
wasn't on the waitqueue at the time. Therefore, IOCB_CMD_POLL
might never complete even if the polled file is ready.
2. When the request isn't on the waitqueue, there is no way to be
notified that the waitqueue is being freed (which happens when its
lifetime is shorter than the struct file's). This is supposed to
happen via the waitqueue entries being woken up with POLLFREE.
Therefore, leave the requests on the waitqueue until they are actually
completed (or cancelled). To keep track of when aio_poll_complete_work
needs to be scheduled, use new fields in struct poll_iocb. Remove the
'done' field which is now redundant.
Note that this is consistent with how sys_poll() and eventpoll work;
their wakeup functions do *not* remove the waitqueue entries.
wake_up_poll() uses nr_exclusive=1, so it's not guaranteed to wake up
all exclusive waiters. Yet, POLLFREE *must* wake up all waiters. epoll
and aio poll are fortunately not affected by this, but it's very
fragile. Thus, the new function wake_up_pollfree() has been introduced.
Convert signalfd to use wake_up_pollfree().
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Fixes: d80e731ecab4 ("epoll: introduce POLLFREE to flush ->signalfd_wqh before kfree()") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211209010455.42744-4-ebiggers@kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wake_up_poll() uses nr_exclusive=1, so it's not guaranteed to wake up
all exclusive waiters. Yet, POLLFREE *must* wake up all waiters. epoll
and aio poll are fortunately not affected by this, but it's very
fragile. Thus, the new function wake_up_pollfree() has been introduced.
Several ->poll() implementations are special in that they use a
waitqueue whose lifetime is the current task, rather than the struct
file as is normally the case. This is okay for blocking polls, since a
blocking poll occurs within one task; however, non-blocking polls
require another solution. This solution is for the queue to be cleared
before it is freed, using 'wake_up_poll(wq, EPOLLHUP | POLLFREE);'.
However, that has a bug: wake_up_poll() calls __wake_up() with
nr_exclusive=1. Therefore, if there are multiple "exclusive" waiters,
and the wakeup function for the first one returns a positive value, only
that one will be called. That's *not* what's needed for POLLFREE;
POLLFREE is special in that it really needs to wake up everyone.
Considering the three non-blocking poll systems:
- io_uring poll doesn't handle POLLFREE at all, so it is broken anyway.
- aio poll is unaffected, since it doesn't support exclusive waits.
However, that's fragile, as someone could add this feature later.
- epoll doesn't appear to be broken by this, since its wakeup function
returns 0 when it sees POLLFREE. But this is fragile.
Although there is a workaround (see epoll), it's better to define a
function which always sends POLLFREE to all waiters. Add such a
function. Also make it verify that the queue really becomes empty after
all waiters have been woken up.
If we successfully cancel a work item but that work item needs to be
processed through task_work, then we can be sleeping uninterruptibly
in io_uring_cancel_generic() and never process it. Hence we don't
make forward progress and we end up with an uninterruptible sleep
warning.
While in there, correct a comment that should be IFF, not IIF.
The ASMedia 1092 has a configuration mode which will present a
dummy device; sadly the implementation falsely claims to provide
a device with 100M which doesn't actually exist.
So disable this device to avoid errors during boot.
Cc: stable@vger.kernel.org Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_fence_chain_find_seqno only ever returns the top fence in the
chain or an unsignalled fence. Hence if we request a seqno that
is already signalled it returns a NULL fence. Some callers are
not prepared to handle this, like the syncobj transfer functions
for example.
This behavior is "new" with timeline syncobj and it looks like
not all callers were updated. To fix this behavior make sure
that a successful drm_sync_find_fence always returns a non-NULL
fence.
v2: Move the fix to drm_syncobj_find_fence from the transfer
functions.
Fixes: ea569910cbab ("drm/syncobj: add transition iotcls between binary and timeline v2") Cc: stable@vger.kernel.org Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl> Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com> Signed-off-by: Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20211208023935.17018-1-bas@basnieuwenhuizen.nl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function mux_get_parent() uses qcom_find_src_index() to find the
parent clock index, which is incorrect: qcom_find_src_index() uses src
enum for the lookup, while mux_get_parent() should use cfg field (which
corresponds to the register value). Add qcom_find_cfg_index() function
doing this kind of lookup and use it for mux parent lookup.
Before commit 86585c61972f ("hwmon: (pwm-fan) stop using legacy
PWM functions and some cleanups") pwm_apply_state() was called
unconditionally in pwm_fan_probe(). In this commit this direct
call was replaced by a call to __set_pwm(ct, MAX_PWM) which
however is a noop if ctx->pwm_value already matches the value to
set.
After probe the fan is supposed to run at full speed, and the
internal driver state suggests it does, but this isn't asserted
and depending on bootloader and pwm low-level driver, the fan
might just be off.
So drop setting pwm_value to MAX_PWM to ensure the check in
__set_pwm doesn't make it exit early and the fan goes on as
intended.
Cc: stable@vger.kernel.org Fixes: 86585c61972f ("hwmon: (pwm-fan) stop using legacy PWM functions and some cleanups") Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20211130092212.17783-1-billy_tsai@aspeedtech.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD proceessors define an address range that is reserved by HyperTransport
and causes a failure if used for guest physical addresses. Avoid
selftests failures by reserving those guest physical addresses; the
rules are:
- On parts with <40 bits, its fully hidden from software.
- Before Fam17h, it was always 12G just below 1T, even if there was more
RAM above this location. In this case we just not use any RAM above 1T.
- On Fam17h and later, it is variable based on SME, and is either just
below 2^48 (no encryption) or 2^43 (encryption).
Fixes: ef4c9f4f6546 ("KVM: selftests: Fix 32-bit truncation of vm_get_max_gfn()") Cc: stable@vger.kernel.org Cc: David Matlack <dmatlack@google.com> Reported-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210805105423.412878-1-pbonzini@redhat.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Tested-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If directories in tracefs have their ownership changed, then any new files
and directories that are created under those directories should inherit
the ownership of the director they are created in.
Link: https://lkml.kernel.org/r/20211208075720.4855d180@gandalf.local.home Cc: Kees Cook <keescook@chromium.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Yabin Cui <yabinc@google.com> Cc: Christian Brauner <christian.brauner@ubuntu.com> Cc: stable@vger.kernel.org Fixes: 4282d60689d4f ("tracefs: Add new tracefs file system") Reported-by: Kalesh Singh <kaleshsingh@google.com>
Reported: https://lore.kernel.org/all/CAC_TJve8MMAv+H_NdLSJXZUSoxOEq2zB_pVaJ9p=7H6Bu3X76g@mail.gmail.com/ Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bd5ae9288d64 ("nfsd: register pernet ops last, unregister first")
has re-opened rpc_pipefs_event() race against nfsd_net_id registration
(register_pernet_subsys()) which has been fixed by commit bb7ffbf29e76
("nfsd: fix nsfd startup race triggering BUG_ON").
Restore the order of register_pernet_subsys() vs register_cld_notifier().
Add WARN_ON() to prevent a future regression.
Crash info:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000012
CPU: 8 PID: 345 Comm: mount Not tainted 5.4.144-... #1
pc : rpc_pipefs_event+0x54/0x120 [nfsd]
lr : rpc_pipefs_event+0x48/0x120 [nfsd]
Call trace:
rpc_pipefs_event+0x54/0x120 [nfsd]
blocking_notifier_call_chain
rpc_fill_super
get_tree_keyed
rpc_fs_get_tree
vfs_get_tree
do_mount
ksys_mount
__arm64_sys_mount
el0_svc_handler
el0_svc
Fixes: bd5ae9288d64 ("nfsd: register pernet ops last, unregister first") Cc: stable@vger.kernel.org Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A delegation break could arrive as soon as we've called vfs_setlease. A
delegation break runs a callback which immediately (in
nfsd4_cb_recall_prepare) adds the delegation to del_recall_lru. If we
then exit nfs4_set_delegation without hashing the delegation, it will be
freed as soon as the callback is done with it, without ever being
removed from del_recall_lru.
Symptoms show up later as use-after-free or list corruption warnings,
usually in the laundromat thread.
I suspect aba2072f4523 "nfsd: grant read delegations to clients holding
writes" made this bug easier to hit, but I looked as far back as v3.0
and it looks to me it already had the same problem. So I'm not sure
where the bug was introduced; it may have been there from the beginning.
Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The superblock of version 1.0 doesn't get moved to the new position on a
device size change. This leads to a rdev without a superblock on a known
position, the raid can't be re-assembled.
The line was removed by mistake and is re-added by this patch.
Fixes: d9c0fa509eaf ("md: fix max sectors calculation for super 1.0") Cc: stable@vger.kernel.org Signed-off-by: Markus Hochholdinger <markus@hochholdinger.net> Reviewed-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FUP packets contain IP information, which makes them also an 'instruction'
event in 'hop' mode i.e. the itrace 'q' option. That wasn't happening, so
restructure the logic so that FUP events are added along with appropriate
'instruction' and 'branch' events.
Fixes: 7c1b16ba0e26e6 ("perf intel-pt: Add support for decoding FUP/TIP only") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org # v5.15+ Link: https://lore.kernel.org/r/20211210162303.2288710-7-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An overflow (OVF packet) is treated as an error because it represents a
loss of trace data, but there is no loss of synchronization, so the packet
state should be INTEL_PT_STATE_IN_SYNC not INTEL_PT_STATE_ERR_RESYNC.
To support that, some additional variables must be reset, and the FUP
packet that may follow OVF is treated as an FUP event.
intel_pt_fup_event() assumes it can overwrite the state type if there has
been an FUP event, but this is an unnecessary and unexpected constraint on
callers.
Fix by touching only the state type flags that are affected by an FUP
event.
Fixes: a472e65fc490a ("perf intel-pt: Add decoder support for ptwrite and power event packets") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: stable@vger.kernel.org # v5.15+ Link: https://lore.kernel.org/r/20211210162303.2288710-4-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When syncing, it may be that branch packet generation is not enabled at
that point, in which case there will not immediately be a control-flow
packet, so some packets before a control flow packet turns up, get
ignored. However, the decoder is in sync as soon as a PSB is found, so
the state should be set accordingly.
In case brtfs_qgroup_reserve_data() or btrfs_delalloc_reserve_metadata()
fail the allocated extent_changeset will not be freed.
So in btrfs_check_data_free_space() and btrfs_delalloc_reserve_space()
free the allocated extent_changeset to get rid of the allocated memory.
The issue currently only happens in the direct IO write path, but only
after 65b3c08606e5 ("btrfs: fix ENOSPC failure when attempting direct IO
write into NOCOW range"), and also at defrag_one_locked_target(). Every
other place is always calling extent_changeset_free() even if its call
to btrfs_delalloc_reserve_space() or btrfs_check_data_free_space() has
failed.
CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log