The UC-257 is a serial + LPT card, so remove it from this driver.
A patch has been submitted to add it to parport_serial instead.
Additionaly, the UC-431 does not use this card ID, only the UC-420
does. The 431 is a 3-port card and there is no generic 3-port configuration
available, so remove reference to it from this driver.
Change lower bcdDevice value for "Super Top USB 2.0 SATA BRIDGE" to match
1.50. I have such an older device with bcdDevice=1.50 and it will not work
otherwise.
The AMD VanGogh SoC contains a DesignWare USB3 Dual-Role Device that can be
operated as either a USB Host or a USB Device, similar to on the AMD Nolan
platform.
be6646bfbaec ("PCI: Prevent xHCI driver from claiming AMD Nolan USB3 DRD
device") added a quirk to let the dwc3 driver claim the Nolan device since
it provides more specific support.
Extend that quirk to include the VanGogh SoC USB3 device.
The reverted commit completely breaks MMC on the AM33xx/AM437x for
multiple reasons:
- The changed compatible strings ti,am335-sdhci and ti,am437-sdhci
aren't supported on Linux 5.4 at all, so no driver is found
- Even when additionally backporting the support for these compatible
strings in the sdhci-omap driver, I could not the the MMC interfaces
to work on our TQMa335x SoM - the interface would time out during card
initialization for both an eMMC and an SD card.
I did not investigate the cause of the timeouts further, and instead
just reverted the commit - switching to a different MMC driver in a stable
kernel seems like a rather risky change unless it's thoroughly tested,
which has obviously not happened in this case.
The reverted commit is also given as a Stable-dep-of commit 2eb502f496f7
("ARM: dts: am33xx: Fix MMCHS0 dma properties"), however the conflict
resulting when only the one commit is reverted is trivial to resolve,
which leads to working MMC controllers again.
From Alon:
"Due to a logical bug in the NVMe-oF/TCP subsystem in the Linux kernel,
a malicious user can cause a UAF and a double free, which may lead to
RCE (may also lead to an LPE in case the attacker already has local
privileges)."
Hence, when a queue initialization fails after the ahash requests are
allocated, it is guaranteed that the queue removal async work will be
called, hence leave the deallocation to the queue removal.
Also, be extra careful not to continue processing the socket, so set
queue rcv_state to NVMET_TCP_RECV_ERR upon a socket error.
Have routines handle errors and just bail out of the poll loop.
This simplifies the code and will help as we may enhance the poll
loop logic and these are somewhat in the way.
This driver is for fairly obscure hardware, and has only seen random
drive-by changes after the maintainer stopped working on it in 2005
(about a year and a half after it was introduced). It has some
"interesting" block layer interactions, so let's just drop it unless
anyone complains.
Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220721064102.1715460-1-hch@lst.de
[axboe: fix date typo, it was in 2005, not 2015] Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-13 slightly changes the type of constant expressions that are defined
in an enum, which triggers a compile time sanity check in libata:
linux/drivers/ata/libahci.c: In function 'ahci_led_store':
linux/include/linux/compiler_types.h:357:45: error: call to '__compiletime_assert_302' declared with attribute error: BUILD_BUG_ON failed: sizeof(_s) > sizeof(long)
357 | _compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
The new behavior is that sizeof() returns the same value for the
constant as it does for the enum type, which is generally more sensible
and consistent.
The problem in libata is that it contains a single enum definition for
lots of unrelated constants, some of which are large positive (unsigned)
integers like 0xffffffff, while others like (1<<31) are interpreted as
negative integers, and this forces the enum type to become 64 bit wide
even though most constants would still fit into a signed 32-bit 'int'.
Fix this by changing the entire enum definition to use BIT(x) in place
of (1<<x), which results in all values being seen as 'unsigned' and
fitting into an unsigned 32-bit type.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107917 Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405 Reported-by: Luis Machado <luis.machado@arm.com> Cc: linux-ide@vger.kernel.org Cc: Damien Le Moal <damien.lemoal@opensource.wdc.com> Cc: stable@vger.kernel.org Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Tested-by: Luis Machado <luis.machado@arm.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
[Backport to linux-5.4.y] Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit fixes the smatch static checker warning in function
mlxbf_tmfifo_rxtx_word() which complains data not initialized at
line 634 when IS_VRING_DROP() is TRUE.
Before this commit all the NOTIFY_BRNDOWN_MIN - NOTIFY_BRNDOWN_MAX
aka 0x20 - 0x2e events were mapped to 0x20.
This mapping is causing issues on new laptop models which actually
send 0x2b events for printscreen presses and 0x2c events for
capslock presses, which get translated into spurious brightness-down
presses.
The plan is disable the 0x11-0x2e special mapping on laptops
where asus-wmi does not register a backlight-device to avoid
the spurious brightness-down keypresses. New laptops always send
0x2e for brightness-down presses, change the special internal
ASUS_WMI_BRN_DOWN value from 0x20 to 0x2e to match this in
preparation for fixing the spurious brightness-down presses.
This change does not have any functional impact since all
of 0x20 - 0x2e is mapped to ASUS_WMI_BRN_DOWN first and only
then checked against the keymap code and the new 0x2e
value is still in the 0x20 - 0x2e range.
Reported-by: James John <me@donjajo.com> Closes: https://lore.kernel.org/platform-driver-x86/a2c441fe-457e-44cf-a146-0ecd86b037cf@donjajo.com/ Closes: https://bbs.archlinux.org/viewtopic.php?pid=2123716 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20231017090725.38163-2-hdegoede@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
We don't want to use the value of ilog2(0) as dummy.buswidth is 0 when
dummy.nbytes is 0. Since we have no dummy bytes, we don't need to
configure the dummy byte bits per clock register value anyway.
ioremap_uc() is only meaningful on old x86-32 systems with the PAT
extension, and on ia64 with its slightly unconventional ioremap()
behavior, everywhere else this is the same as ioremap() anyway.
Change the only driver that still references ioremap_uc() to only do so
on x86-32/ia64 in order to allow removing that interface at some
point in the future for the other architectures.
On some architectures, ioremap_uc() just returns NULL, changing
the driver to call ioremap() means that they now have a chance
of working correctly.
Touch controllers need some time after receiving reset command for the
firmware to finish re-initializing and be ready to respond to commands
from the host. The driver already had handling for the post-reset delay
for I2C and SPI transports, this change adds the handling to
SMBus-connected devices.
SMBus devices are peculiar because they implement legacy PS/2
compatibility mode, so reset is actually issued by psmouse driver on the
associated serio port, after which the control is passed to the RMI4
driver with SMBus companion device.
Note that originally the delay was added to psmouse driver in 92e24e0e57f7 ("Input: psmouse - add delay when deactivating for SMBus
mode"), but that resulted in an unwanted delay in "fast" reconnect
handler for the serio port, so it was decided to revert the patch and
have the delay being handled in the RMI4 driver, similar to the other
transports.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
We fix it by calling pm_runtime_disable when error returns.
The STM32F4/7 EXTI driver was missing the xlate callback, so IRQ trigger
flags specified in the device tree were being ignored. This was
preventing the RTC alarm interrupt from working, because it must be set
to trigger on the rising edge to function correctly.
In the initial boot stage the integrated keyboard of Fujitsu Lifebook E5411
refuses to work and it's not possible to type for example a dm-crypt
passphrase without the help of an external keyboard.
i8042.nomux kernel parameter resolves this issue but using that a PS/2
mouse is detected. This input device is unused even when the i2c-hid-acpi
kernel module is blacklisted making the integrated ELAN touchpad
(04F3:308A) not working at all.
Since the integrated touchpad is managed by the i2c_designware input
driver in the Linux kernel and you can't find a PS/2 mouse port on the
computer I think it's safe to not use the PS/2 mouse port at all.
Commit in Fixes added the "NOLOAD" attribute to the .brk section as a
"failsafe" measure.
Unfortunately, this leads to the linker no longer covering the .brk
section in a program header, resulting in the kernel loader not knowing
that the memory for the .brk section must be reserved.
This has led to crashes when loading the kernel as PV dom0 under Xen,
but other scenarios could be hit by the same problem (e.g. in case an
uncompressed kernel is used and the initrd is placed directly behind
it).
So drop the "NOLOAD" attribute. This has been verified to correctly
cover the .brk section by a program header of the resulting ELF file.
driver_set_override() helper uses device_lock() so it should not be
called before rpmsg_register_device() (which calls device_register()).
Effect can be seen with CONFIG_DEBUG_MUTEXES:
Refactor the rpmsg_register_device() function to use two-step device
registering (initialization + add) and call driver_set_override() in
proper moment.
This moves the code around, so while at it also NULL-ify the
rpdev->driver_override in error path to be sure it won't be kfree()
second time.
Fixes: 42cd402b8fd4 ("rpmsg: Fix kfree() of static memory on setting driver_override") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20220429195946.1061725-2-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver_override field from platform driver should not be initialized
from static memory (string literal) because the core later kfree() it,
for example when driver_override is set via sysfs.
Use dedicated helper to set driver_override properly.
Fixes: 950a7388f02b ("rpmsg: Turn name service into a stand alone driver") Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface") Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220419113435.246203-13-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several core drivers and buses expect that driver_override is a
dynamically allocated memory thus later they can kfree() it.
However such assumption is not documented, there were in the past and
there are already users setting it to a string literal. This leads to
kfree() of static memory during device release (e.g. in error paths or
during unbind):
kernel BUG at ../mm/slub.c:3960!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
...
(kfree) from [<c058da50>] (platform_device_release+0x88/0xb4)
(platform_device_release) from [<c0585be0>] (device_release+0x2c/0x90)
(device_release) from [<c0a69050>] (kobject_put+0xec/0x20c)
(kobject_put) from [<c0f2f120>] (exynos5_clk_probe+0x154/0x18c)
(exynos5_clk_probe) from [<c058de70>] (platform_drv_probe+0x6c/0xa4)
(platform_drv_probe) from [<c058b7ac>] (really_probe+0x280/0x414)
(really_probe) from [<c058baf4>] (driver_probe_device+0x78/0x1c4)
(driver_probe_device) from [<c0589854>] (bus_for_each_drv+0x74/0xb8)
(bus_for_each_drv) from [<c058b48c>] (__device_attach+0xd4/0x16c)
(__device_attach) from [<c058a638>] (bus_probe_device+0x88/0x90)
(bus_probe_device) from [<c05871fc>] (device_add+0x3dc/0x62c)
(device_add) from [<c075ff10>] (of_platform_device_create_pdata+0x94/0xbc)
(of_platform_device_create_pdata) from [<c07600ec>] (of_platform_bus_create+0x1a8/0x4fc)
(of_platform_bus_create) from [<c0760150>] (of_platform_bus_create+0x20c/0x4fc)
(of_platform_bus_create) from [<c07605f0>] (of_platform_populate+0x84/0x118)
(of_platform_populate) from [<c0f3c964>] (of_platform_default_populate_init+0xa0/0xb8)
(of_platform_default_populate_init) from [<c01031f8>] (do_one_initcall+0x8c/0x404)
Provide a helper which clearly documents the usage of driver_override.
This will allow later to reuse the helper and reduce the amount of
duplicated code.
Convert the platform driver to use a new helper and make the
driver_override field const char (it is not modified by the core).
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220419113435.246203-2-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we calculate the end position of ext4_free_extent, this position may
be exactly where ext4_lblk_t (i.e. uint) overflows. For example, if
ac_g_ex.fe_logical is 4294965248 and ac_orig_goal_len is 2048, then the
computed end is 0x100000000, which is 0. If ac->ac_o_ex.fe_logical is not
the first case of adjusting the best extent, that is, new_bex_end > 0, the
following BUG_ON will be triggered:
We simply refactor the logic for adjusting the best extent by adding
a temporary ext4_free_extent ex and use extent_logical_end() to avoid
overflow, which also simplifies the code.
Cc: stable@kernel.org # 6.4 Fixes: 93cdf49f6eca ("ext4: Fix best extent lstart adjustment logic in ext4_mb_new_inode_pa()") Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com> Link: https://lore.kernel.org/r/20230724121059.11834-3-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's say we want to allocate 2 blocks starting from 4294966386, after
predicting the file size, start is aligned to 4294965248, len is changed
to 2048, then end = start + size = 0x100000000. Since end is of
type ext4_lblk_t, i.e. uint, end is truncated to 0.
This causes (pa->pa_lstart >= end) to always hold when checking if the
current extent to be allocated crosses already preallocated blocks, so the
resulting ac_g_ex may cross already preallocated blocks. Hence we convert
the end type to loff_t and use pa_logical_end() to avoid overflow.
When we use lstart + len to calculate the end of free extent or prealloc
space, it may exceed the maximum value of 4294967295(0xffffffff) supported
by ext4_lblk_t and cause overflow, which may lead to various problems.
Therefore, we add two helper functions, extent_logical_end() and
pa_logical_end(), to limit the type of end to loff_t, and also convert
lstart to loff_t for calculation to avoid overflow.
With binutils 2.26, RESERVE_BRK() causes a build failure:
/tmp/ccnGOKZ5.s: Assembler messages:
/tmp/ccnGOKZ5.s:98: Error: missing ')'
/tmp/ccnGOKZ5.s:98: Error: missing ')'
/tmp/ccnGOKZ5.s:98: Error: missing ')'
/tmp/ccnGOKZ5.s:98: Error: junk at end of line, first unrecognized
character is `U'
The problem is this line:
RESERVE_BRK(early_pgt_alloc, INIT_PGT_BUF_SIZE)
Specifically, the INIT_PGT_BUF_SIZE macro which (via PAGE_SIZE's use
_AC()) has a "1UL", which makes older versions of the assembler unhappy.
Unfortunately the _AC() macro doesn't work for inline asm.
Inline asm was only needed here to convince the toolchain to add the
STT_NOBITS flag. However, if a C variable is placed in a section whose
name is prefixed with ".bss", GCC and Clang automatically set
STT_NOBITS. In fact, ".bss..page_aligned" already relies on this trick.
So fix the build failure (and simplify the macro) by allocating the
variable in C.
Also, add NOLOAD to the ".brk" output section clause in the linker
script. This is a failsafe in case the ".bss" prefix magic trick ever
stops working somehow. If there's a section type mismatch, the GNU
linker will force the ".brk" output section to be STT_NOBITS. The LLVM
linker will fail with a "section type mismatch" error.
Note this also changes the name of the variable from .brk.##name to
__brk_##name. The variable names aren't actually used anywhere, so it's
harmless.
Fixes: a1e2c031ec39 ("x86/mm: Simplify RESERVE_BRK()") Reported-by: Joe Damato <jdamato@fastly.com> Reported-by: Byungchul Park <byungchul.park@lge.com> Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Joe Damato <jdamato@fastly.com> Link: https://lore.kernel.org/r/22d07a44c80d8e8e1e82b9a806ddc8c6bbb2606e.1654759036.git.jpoimboe@kernel.org
[nathan: Fix conflict due to lack of 360db4ace311 and resolve silent
conflict with 360db4ace3117] Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RESERVE_BRK() reserves data in the .brk_reservation section. The data
is initialized to zero, like BSS, so the macro specifies 'nobits' to
prevent the data from taking up space in the vmlinux binary. The only
way to get the compiler to do that (without putting the variable in .bss
proper) is to use inline asm.
The macro also has a hack which encloses the inline asm in a discarded
function, which allows the size to be passed (global inline asm doesn't
allow inputs).
Remove the need for the discarded function hack by just stringifying the
size rather than supplying it as an input to the inline asm.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Borislav Petkov <bp@suse.de> Link: https://lore.kernel.org/r/20220506121631.133110232@infradead.org
[nathan: Fix conflict due to lack of 2b6ff7dea670 and 33def8498fdd] Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
F2FS-fs (loop0): sanity_check_inode: inode (ino=49) extent info [5942, 4294180864, 4] is incorrect, run fsck to fix
F2FS-fs (loop0): f2fs_check_nid_range: out-of-range nid=31340049, run fsck to fix.
BUG: kernel NULL pointer dereference, address: 0000000000000000
folio_mark_dirty+0x33/0x50
move_data_page+0x2dd/0x460 [f2fs]
do_garbage_collect+0xc18/0x16a0 [f2fs]
f2fs_gc+0x1d3/0xd90 [f2fs]
f2fs_balance_fs+0x13a/0x570 [f2fs]
f2fs_create+0x285/0x840 [f2fs]
path_openat+0xe6d/0x1040
do_filp_open+0xc5/0x140
do_sys_openat2+0x23a/0x310
do_sys_open+0x57/0x80
The root cause is for special file: e.g. character, block, fifo or socket file,
f2fs doesn't assign address space operations pointer array for mapping->a_ops field,
so, in a fuzzed image, SSA table indicates a data block belong to special file, when
f2fs tries to migrate that block, it causes NULL pointer access once move_data_page()
calls a_ops->set_dirty_page().
There were two places where we weren't checking for error
(e.g. ERESTARTSYS) while waiting for rdma resolution.
Addresses-Coverity: 1462165 ("Unchecked return value") Reviewed-by: Tom Talpey <tom@talpey.com> Reviewed-by: Long Li <longli@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Anastasia Belova <abelova@astralinux.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In kobject_get_path(), if kobj->name is changed between calls
get_kobj_path_length() and fill_kobj_path() and the length becomes
longer, then fill_kobj_path() will have an out-of-bounds bug.
The actual current problem occurs when the ixgbe probe.
In ixgbe_mii_bus_init(), if the length of netdev->dev.kobj.name
length becomes longer, out-of-bounds will occur.
cpu0 cpu1
ixgbe_probe
register_netdev(netdev)
netdev_register_kobject
device_add
kobject_uevent // Sending ADD events
systemd-udevd // rename netdev
dev_change_name
device_rename
kobject_rename
ixgbe_mii_bus_init |
mdiobus_register |
__mdiobus_register |
device_register |
device_add |
kobject_uevent |
kobject_get_path |
len = get_kobj_path_length // old name |
path = kzalloc(len, gfp_mask); |
kobj->name = name;
/* name length becomes
* longer
*/
fill_kobj_path /* kobj path length is
* longer than path,
* resulting in out of
* bounds when filling path
*/
This is the kasan report:
==================================================================
BUG: KASAN: slab-out-of-bounds in fill_kobj_path+0x50/0xc0
Write of size 7 at addr ff1100090573d1fd by task kworker/28:1/673
Jinjie Ruan [Mon, 30 Oct 2023 06:37:09 +0000 (06:37 +0000)]
arm64: fix a concurrency issue in emulation_proc_handler()
In linux-6.1, the related code is refactored in commit 124c49b1b5d9
("arm64: armv8_deprecated: rework deprected instruction handling") and this
issue was incidentally fixed. I have adapted the patch set to linux stable
5.10. However, 4.19 and 5.10 are too different and the patch set is
hard to adapt to 4.19.
This patch is to solve the problem of repeated addition of linked lists
described below with few changes.
How to reproduce:
CONFIG_ARMV8_DEPRECATED=y, CONFIG_SWP_EMULATION=y, and CONFIG_DEBUG_LIST=y,
then launch two shell executions:
#!/bin/bash
while [ 1 ];
do
echo 1 > /proc/sys/abi/swp
done
or "echo 1 > /proc/sys/abi/swp" and then aunch two shell executions:
#!/bin/bash
while [ 1 ];
do
echo 0 > /proc/sys/abi/swp
done
In emulation_proc_handler(), read and write operations are performed on
insn->current_mode. In the concurrency scenario, mutex only protects
writing insn->current_mode, and not protects the read. Suppose there are
two concurrent tasks, task1 updates insn->current_mode to INSN_EMULATE
in the critical section, the prev_mode of task2 is still the old data
INSN_UNDEF of insn->current_mode. As a result, two tasks call
update_insn_emulation_mode twice with prev_mode = INSN_UNDEF and
current_mode = INSN_EMULATE, then call register_emulation_hooks twice,
resulting in a list_add double problem.
After applying this patch, the following list add or list del double
warnings never occur.
As drm_dp_get_mst_branch_device_by_guid() is called from
drm_dp_get_mst_branch_device_by_guid(), mstb parameter has to be checked,
otherwise NULL dereference may occur in the call to
the memcpy() and cause following:
As get_mst_branch_device_by_guid_helper() is recursive, moving condition
to the first line allow to remove a similar one for step over of NULL elements
inside a loop.
Fixes: 5e93b8208d3c ("drm/dp/mst: move GUID storage from mgr, port to only mst branch") Cc: <stable@vger.kernel.org> # 4.14+ Signed-off-by: Lukasz Majczak <lma@semihalf.com> Reviewed-by: Radoslaw Biernacki <rad@chromium.org> Signed-off-by: Manasi Navare <navaremanasi@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230922063410.23626-1-lma@semihalf.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David and a few others reported that on certain newer systems some legacy
interrupts fail to work correctly.
Debugging revealed that the BIOS of these systems leaves the legacy PIC in
uninitialized state which makes the PIC detection fail and the kernel
switches to a dummy implementation.
Unfortunately this fallback causes quite some code to fail as it depends on
checks for the number of legacy PIC interrupts or the availability of the
real PIC.
In theory there is no reason to use the PIC on any modern system when
IO/APIC is available, but the dependencies on the related checks cannot be
resolved trivially and on short notice. This needs lots of analysis and
rework.
The PIC detection has been added to avoid quirky checks and force selection
of the dummy implementation all over the place, especially in VM guest
scenarios. So it's not an option to revert the relevant commit as that
would break a lot of other scenarios.
One solution would be to try to initialize the PIC on detection fail and
retry the detection, but that puts the burden on everything which does not
have a PIC.
Fortunately the ACPI/MADT table header has a flag field, which advertises
in bit 0 that the system is PCAT compatible, which means it has a legacy
8259 PIC.
Evaluate that bit and if set avoid the detection routine and keep the real
PIC installed, which then gets initialized (for nothing) and makes the rest
of the code with all the dependencies work again.
Fixes: e179f6914152 ("x86, irq, pic: Probe for legacy PIC and set legacy_pic appropriately") Reported-by: David Lazar <dlazar@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: David Lazar <dlazar@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Cc: stable@vger.kernel.org Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218003 Link: https://lore.kernel.org/r/875y2u5s8g.ffs@tglx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The I40E_TXR_FLAGS_WB_ON_ITR is i40e_ring flag and not i40e_pf one.
Fixes: 8e0764b4d6be42 ("i40e/i40evf: Add support for writeback on ITR feature for X722") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20231023212714.178032-1-jacob.e.keller@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the possible_parent_show function, ensure proper handling of the return
value from of_clk_get_parent_name to prevent potential issues arising from
a NULL return.
The current implementation invokes seq_puts directly on the result of
of_clk_get_parent_name without verifying the return value, which can lead
to kernel panic if the function returns NULL.
This patch addresses the concern by introducing a check on the return
value of of_clk_get_parent_name. If the return value is not NULL, the
function proceeds to call seq_puts, providing the returned value as
argument.
However, if of_clk_get_parent_name returns NULL, the function provides a
static string as argument, avoiding the panic.
Fixes: 1ccc0ddf046a ("clk: Use seq_puts() in possible_parent_show()") Reported-by: Philip Daly <pdaly@redhat.com> Signed-off-by: Alessandro Carminati (Red Hat) <alessandro.carminati@gmail.com> Link: https://lore.kernel.org/r/20230921073217.572151-1-alessandro.carminati@gmail.com Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the `CONFIG_I2C_SLAVE` option is enabled and the device operates
as a slave, a situation arises where the master sends a START signal
without the accompanying STOP signal. This action results in a
persistent I2C bus timeout. The core issue stems from the fact that
the i2c controller remains in a slave read state without a timeout
mechanism. As a consequence, the bus perpetually experiences timeouts.
In this case, the i2c bus will be reset, but the slave_state reset is
missing.
Fixes: fee465150b45 ("i2c: aspeed: Reset the i2c controller when timeout occurs") Signed-off-by: Jian Zhang <zhangjian.3032@bytedance.com> Acked-by: Andi Shyti <andi.shyti@kernel.org> Tested-by: Andrew Jeffery <andrew@codeconstruct.com.au> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of SMBUS byte read with PEC enabled, the whole transfer
is split into two commands. A first write command, followed by
a read command. The write command does not have any PEC byte
and a PEC byte is appended at the end of the read command.
(cf Read byte protocol with PEC in SMBUS specification)
Within the STM32 I2C controller, handling (either sending
or receiving) of the PEC byte is done via the PECBYTE bit in
register CR2.
Currently, the PECBYTE is set at the beginning of a transfer,
which lead to sending a PEC byte at the end of the write command
(hence losing the real last byte), and also does not check the
PEC byte received during the read command.
This patch corrects the function stm32f7_i2c_smbus_xfer_msg
in order to only set the PECBYTE during the read command.
i2c-demux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: 50a5ba876908 ("i2c: mux: demux-pinctrl: add driver") Signed-off-by: Herve Codina <herve.codina@bootlin.com> Cc: stable@vger.kernel.org Acked-by: Peter Rosin <peda@axentia.se> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c-mux-gpmux uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: ac8498f0ce53 ("i2c: i2c-mux-gpmux: new driver") Signed-off-by: Herve Codina <herve.codina@bootlin.com> Cc: stable@vger.kernel.org Acked-by: Peter Rosin <peda@axentia.se> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c-mux-pinctrl uses the pair of_find_i2c_adapter_by_node() /
i2c_put_adapter(). These pair alone is not correct to properly lock the
I2C parent adapter.
Indeed, i2c_put_adapter() decrements the module refcount while
of_find_i2c_adapter_by_node() does not increment it. This leads to an
underflow of the parent module refcount.
Use the dedicated function, of_get_i2c_adapter_by_node(), to handle
correctly the module refcount.
Fixes: c4aee3e1b0de ("i2c: mux: pinctrl: remove platform_data") Signed-off-by: Herve Codina <herve.codina@bootlin.com> Cc: stable@vger.kernel.org Acked-by: Peter Rosin <peda@axentia.se> Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Second interrupt is needed only when touchscreen mode is used, so don't
request it unconditionally. This removes the following annoying warning
during boot:
exynos-adc 14d10000.adc: error -ENXIO: IRQ index 1 not found
This commit fix wrong RTO timeout when received SACK reneging.
When an ACK arrived pointing to a SACK reneging, tcp_check_sack_reneging()
will rearm the RTO timer for min(1/2*srtt, 10ms) into to the future.
But since the commit 62d9f1a6945b ("tcp: fix TLP timer not set when
CA_STATE changes from DISORDER to OPEN") merged, the tcp_set_xmit_timer()
is moved after tcp_fastretrans_alert()(which do the SACK reneging check),
so the RTO timeout will be overwrited by tcp_set_xmit_timer() with
icsk_rto instead of 1/2*srtt.
Here is a packetdrill script to check this bug:
0 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
+0 bind(3, ..., ...) = 0
+0 listen(3, 1) = 0
// we expect rto fired in 1/2*srtt (50ms)
+.05 > . 1001:2001(1000) ack 1
This fix remove the FLAG_SET_XMIT_TIMER from ack_flag when
tcp_check_sack_reneging() set RTO timer with 1/2*srtt to avoid
being overwrited later.
Fixes: 62d9f1a6945b ("tcp: fix TLP timer not set when CA_STATE changes from DISORDER to OPEN") Signed-off-by: Fred Chen <fred.chenchen03@gmail.com> Reviewed-by: Neal Cardwell <ncardwell@google.com> Tested-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error handling in rtl8152_probe() is missing a call to cancel the
hw_phy_work. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: a028a9e003f2 ("r8152: move the settings of PHY to a work queue") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b69301c ("net/usb: new driver for RTL8152") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b69301c ("net/usb: new driver for RTL8152") Suggested-by: Hayes Wang <hayeswang@realtek.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
strncat() usage in adf7242_debugfs_init() is wrong.
The size given to strncat() is the maximum number of bytes that can be
written, excluding the trailing NULL.
Here, the size that is passed, DNAME_INLINE_LEN, does not take into account
the size of "adf7242-" that is already in the array.
In order to fix it, use snprintf() instead.
Fixes: 7302b9d90117 ("ieee802154/adf7242: Driver for ADF7242 MAC IEEE802154") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'ethtool_convert_link_mode_to_legacy_u32' method does not allow us to
advertise 2500M speed support and TP (twisted pair) properly. Convert to
'ethtool_link_ksettings_test_link_mode' to advertise supported speed and
eliminate ambiguity.
Add check for return of igb_update_ethtool_nfc_entry so that in case
of any potential errors the memory alocated for input will be freed.
Fixes: 0e71def25281 ("igb: add support of RX network flow classification") Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel) Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
==================================================================
BUG: KCSAN: data-race in rtl8169_poll (drivers/net/ethernet/realtek/r8169_main.c:4430 drivers/net/ethernet/realtek/r8169_main.c:4583) r8169
race at unknown origin, with read to 0xffff888117e43510 of 4 bytes by interrupt on cpu 21:
rtl8169_poll (drivers/net/ethernet/realtek/r8169_main.c:4430 drivers/net/ethernet/realtek/r8169_main.c:4583) r8169
__napi_poll (net/core/dev.c:6527)
net_rx_action (net/core/dev.c:6596 net/core/dev.c:6727)
__do_softirq (kernel/softirq.c:553)
__irq_exit_rcu (kernel/softirq.c:427 kernel/softirq.c:632)
irq_exit_rcu (kernel/softirq.c:647)
sysvec_apic_timer_interrupt (arch/x86/kernel/apic/apic.c:1074 (discriminator 14))
asm_sysvec_apic_timer_interrupt (./arch/x86/include/asm/idtentry.h:645)
cpuidle_enter_state (drivers/cpuidle/cpuidle.c:291)
cpuidle_enter (drivers/cpuidle/cpuidle.c:390)
call_cpuidle (kernel/sched/idle.c:135)
do_idle (kernel/sched/idle.c:219 kernel/sched/idle.c:282)
cpu_startup_entry (kernel/sched/idle.c:378 (discriminator 1))
start_secondary (arch/x86/kernel/smpboot.c:210 arch/x86/kernel/smpboot.c:294)
secondary_startup_64_no_verify (arch/x86/kernel/head_64.S:433)
value changed: 0x80003fff -> 0x3402805f
Reported by Kernel Concurrency Sanitizer on:
CPU: 21 PID: 0 Comm: swapper/21 Tainted: G L 6.6.0-rc2-kcsan-00143-gb5cbe7c00aa0 #41
Hardware name: ASRock X670E PG Lightning/X670E PG Lightning, BIOS 1.21 04/26/2023
==================================================================
drivers/net/ethernet/realtek/r8169_main.c:
==========================================
4429
→ 4430 status = le32_to_cpu(desc->opts1);
4431 if (status & DescOwn)
4432 break;
4433
4434 /* This barrier is needed to keep us from reading
4435 * any other fields out of the Rx descriptor until
4436 * we know the status of DescOwn
4437 */
4438 dma_rmb();
4439
4440 if (unlikely(status & RxRES)) {
4441 if (net_ratelimit())
4442 netdev_warn(dev, "Rx ERROR. status = %08x\n",
Marco Elver explained that dma_rmb() doesn't prevent the compiler to tear up the access to
desc->opts1 which can be written to concurrently. READ_ONCE() should prevent that from
happening:
4429
→ 4430 status = le32_to_cpu(READ_ONCE(desc->opts1));
4431 if (status & DescOwn)
4432 break;
4433
As the consequence of this fix, this KCSAN warning was eliminated.
Fixes: 6202806e7c03a ("r8169: drop member opts1_mask from struct rtl8169_private") Suggested-by: Marco Elver <elver@google.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: nic_swsd@realtek.com Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: netdev@vger.kernel.org Link: https://lore.kernel.org/lkml/dc7fc8fa-4ea4-e9a9-30a6-7c83e6b53188@alu.unizg.hr/ Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Acked-by: Marco Elver <elver@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the recent removal of vm_dev from devres its memory is only freed
via the callback virtio_mmio_release_dev. However, this only takes
effect after device_add is called by register_virtio_device. Until then
it's an unmanaged resource and must be explicitly freed on error exit.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Cc: stable@vger.kernel.org Fixes: 55c91fedd03d ("virtio-mmio: don't break lifecycle of vm_dev") Signed-off-by: Maximilian Heyne <mheyne@amazon.de> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Tested-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Message-Id: <20230911090328.40538-1-mheyne@amazon.de> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
The deflation request to the target, which isn't unaligned to the
guest page size causes endless deflation and inflation actions. For
example, we receive the flooding QMP events for the changes on memory
balloon's size after a deflation request to the unaligned target is
sent for the ARM64 guest, where we have 64KB base page size.
Fix it by aligning the target up to the guest page size, 64KB in this
specific case. With this applied, no flooding QMP events are observed
and the memory balloon's size can be stablizied to 0x3ffe0000 soon
after the deflation request is sent.
mcb-lpc requests a fixed-size memory region to parse the chameleon
table, however, if the chameleon table is smaller that the allocated
region, it could overlap with the IP Cores' memory regions.
After parsing the chameleon table, drop/reallocate the memory region
with the actual chameleon table size.
The function chameleon_parse_cells() returns the number of cells
parsed which has an undetermined size. This return value is only
used for error checking but the number of cells is never used.
Change return value to be number of bytes parsed to allow for
memory management improvements.
If name_show() is non unique, this test will try to install a kprobe on this
function which should fail returning EADDRNOTAVAIL.
On kernel where name_show() is not unique, this test is skipped.
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
There are race conditions that may lead to inet6_dev refcount underflow
in xfrm6_dst_destroy() and rt6_uncached_list_flush_dev().
One of the refcount underflow bugs is shown below:
(cpu 1) | (cpu 2)
xfrm6_dst_destroy() |
... |
in6_dev_put() |
| rt6_uncached_list_flush_dev()
... | ...
| in6_dev_put()
rt6_uncached_list_del() | ...
... |
xfrm6_dst_destroy() calls rt6_uncached_list_del() after in6_dev_put(),
so rt6_uncached_list_flush_dev() has a chance to call in6_dev_put()
again for the same inet6_dev.
Fix it by moving in6_dev_put() after rt6_uncached_list_del() in
xfrm6_dst_destroy().
The code pattern of memcpy(dst, src, strlen(src)) is almost always
wrong. In this case it is wrong because it leaves memory uninitialized
if it is less than sizeof(ni->name), and overflows ni->name when longer.
Normally strtomem_pad() could be used here, but since ni->name is a
trailing array in struct hci_mon_new_index, compilers that don't support
-fstrict-flex-arrays=3 can't tell how large this array is via
__builtin_object_size(). Instead, open-code the helper and use sizeof()
since it will work correctly.
Additionally mark ni->name as __nonstring since it appears to not be a
%NUL terminated C string.
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Edward AD <twuufnxlz@gmail.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: linux-bluetooth@vger.kernel.org Cc: netdev@vger.kernel.org Fixes: 18f547f3fc07 ("Bluetooth: hci_sock: fix slab oob read in create_monitor_event") Link: https://lore.kernel.org/lkml/202310110908.F2639D3276@keescook/ Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like the driver sleep pins configuration is unusable. Adding the
sleep pins causes the usb phy to not respond. We need to use the default
pins in probe, and only set sleep pins at phy_mdm6600_device_power_off().
As the modem can also be booted to a serial port mode for firmware
flashing, let's make the pin changes limited to probe and remove. For
probe, we get the default pins automatically. We only need to set the
sleep pins in phy_mdm6600_device_power_off() to prevent the modem from
waking up because the gpio line glitches.
If it turns out that we need a separate state for phy_mdm6600_power_on()
and phy_mdm6600_power_off(), we can use the pinctrl idle state.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Fixes: 2ad2af081622 ("phy: mapphone-mdm6600: Improve phy related runtime PM calls") Signed-off-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Link: https://lore.kernel.org/r/20230913060433.48373-3-tony@atomide.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit d644e0d79829 ("phy: mapphone-mdm6600: Fix PM error handling in
phy_mdm6600_probe") caused a regression where we now unconditionally
disable runtime PM at the end of the probe while it is only needed on
errors.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Miaoqian Lin <linmq006@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Fixes: d644e0d79829 ("phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe") Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20230913060433.48373-1-tony@atomide.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Free the "priv" pointer before returning the error code.
Fixes: 90eb6b59d311 ("ASoC: pxa-ssp: add support for an external clock in devicetree") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/84ac2313-1420-471a-b2cb-3269a2e12a7c@moroto.mountain Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We found a glitch when configuring the pad as output high. To avoid this
glitch, move the data value setting before direction config in the
function vf610_gpio_direction_output().
Since the fixed commits both zdev->iommu_bitmap and zdev->lazy_bitmap
are allocated as vzalloc(zdev->iommu_pages / 8). The problem is that
zdev->iommu_bitmap is a pointer to unsigned long but the above only
yields an allocation that is a multiple of sizeof(unsigned long) which
is 8 on s390x if the number of IOMMU pages is a multiple of 64.
This in turn is the case only if the effective IOMMU aperture is
a multiple of 64 * 4K = 256K. This is usually the case and so didn't
cause visible issues since both the virt_to_phys(high_memory) reduced
limit and hardware limits use nice numbers.
Under KVM, and in particular with QEMU limiting the IOMMU aperture to
the vfio DMA limit (default 65535), it is possible for the reported
aperture not to be a multiple of 256K however. In this case we end up
with an iommu_bitmap whose allocation is not a multiple of
8 causing bitmap operations to access it out of bounds.
Sadly we can't just fix this in the obvious way and use bitmap_zalloc()
because for large RAM systems (tested on 8 TiB) the zdev->iommu_bitmap
grows too large for kmalloc(). So add our own bitmap_vzalloc() wrapper.
This might be a candidate for common code, but this area of code will
be replaced by the upcoming conversion to use the common code DMA API on
s390 so just add a local routine.
Fixes: 224593215525 ("s390/pci: use virtual memory for iommu bitmap") Fixes: 13954fd6913a ("s390/pci_dma: improve lazy flush for unmap") Cc: stable@vger.kernel.org Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because group consistency is non-atomic between parent (filedesc) and children
(inherited) events, it is possible for PERF_FORMAT_GROUP read() to try and sum
non-matching counter groups -- with non-sensical results.
Add group_generation to distinguish the case where a parent group removes and
adds an event and thus has the same number, but a different configuration of
events as inherited groups.
This became a problem when commit fa8c269353d5 ("perf/core: Invert
perf_read_group() loops") flipped the order of child_list and sibling_list.
Previously it would iterate the group (sibling_list) first, and for each
sibling traverse the child_list. In this order, only the group composition of
the parent is relevant. By flipping the order the group composition of the
child (inherited) events becomes an issue and the mis-match in group
composition becomes evident.
That said; even prior to this commit, while reading of a group that is not
equally inherited was not broken, it still made no sense.
(Ab)use ECHILD as error return to indicate issues with child process group
composition.
acpi_register_gsi() should return a negative value in case of failure.
Currently, it returns the return value from irq_create_fwspec_mapping().
However, irq_create_fwspec_mapping() returns 0 for failure. Fix the
issue by returning -EINVAL if irq_create_fwspec_mapping() returns zero.
Fixes: d44fa3d46079 ("ACPI: Add support for ResourceSource/IRQ domain mapping") Cc: 4.11+ <stable@vger.kernel.org> # 4.11+ Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
[ rjw: Rename a new local variable ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OEMID is an 8-bit binary number rather than 16-bit as the current code
parses for. The OEMID occupies bits [111:104] in the CID register, see the
eMMC spec JESD84-B51 paragraph 7.2.3. It seems that the 16-bit comes from
the legacy MMC specs (v3.31 and before).
Let's fix the parsing by simply move to use 8-bit instead of 16-bit. This
means we ignore the impact on some of those old MMC cards that may be out
there, but on the other hand this shouldn't be a problem as the OEMID seems
not be an important feature for these cards.
tuning only support in 4-bit mode or 8 bit mode, so in 1-bit mode,
need to hold retuning.
Find this issue when use manual tuning method on imx93. When system
resume back, SDIO WIFI try to switch back to 4 bit mode, first will
trigger retuning, and all tuning command failed.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: dfa13ebbe334 ("mmc: host: Add facility to support re-tuning") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230830093922.3095850-1-haibo.chen@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the exact mapping type driver was not available, the old
physmap_of_core driver fell back to mapping the region as ROM.
Unfortunately this feature was lost when the DT and pdata cases were
merged. Revive this useful feature.
memcmp is not consider safe to use with cryptographic secrets:
'Do not use memcmp() to compare security critical data, such as
cryptographic secrets, because the required CPU time depends on the
number of equal bytes.'
While usage of memcmp for ZERO_KEY may not be considered a security
critical data, it can lead to more usage of memcmp with pairing keys
which could introduce more security problems.
Fixes: 455c2ff0a558 ("Bluetooth: Fix BR/EDR out-of-band pairing with only initiator data") Fixes: 33155c4aae52 ("Bluetooth: hci_event: Ignore NULL link key") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Jens reported the following warnings from -Wmaybe-uninitialized recent
Linus' branch.
In file included from ./include/asm-generic/rwonce.h:26,
from ./arch/arm64/include/asm/rwonce.h:71,
from ./include/linux/compiler.h:246,
from ./include/linux/export.h:5,
from ./include/linux/linkage.h:7,
from ./include/linux/kernel.h:17,
from fs/btrfs/ioctl.c:6:
In function ‘instrument_copy_from_user_before’,
inlined from ‘_copy_from_user’ at ./include/linux/uaccess.h:148:3,
inlined from ‘copy_from_user’ at ./include/linux/uaccess.h:183:7,
inlined from ‘btrfs_ioctl_space_info’ at fs/btrfs/ioctl.c:2999:6,
inlined from ‘btrfs_ioctl’ at fs/btrfs/ioctl.c:4616:10:
./include/linux/kasan-checks.h:38:27: warning: ‘space_args’ may be used
uninitialized [-Wmaybe-uninitialized]
38 | #define kasan_check_write __kasan_check_write
./include/linux/instrumented.h:129:9: note: in expansion of macro
‘kasan_check_write’
129 | kasan_check_write(to, n);
| ^~~~~~~~~~~~~~~~~
./include/linux/kasan-checks.h: In function ‘btrfs_ioctl’:
./include/linux/kasan-checks.h:20:6: note: by argument 1 of type ‘const
volatile void *’ to ‘__kasan_check_write’ declared here
20 | bool __kasan_check_write(const volatile void *p, unsigned int
size);
| ^~~~~~~~~~~~~~~~~~~
fs/btrfs/ioctl.c:2981:39: note: ‘space_args’ declared here
2981 | struct btrfs_ioctl_space_args space_args;
| ^~~~~~~~~~
In function ‘instrument_copy_from_user_before’,
inlined from ‘_copy_from_user’ at ./include/linux/uaccess.h:148:3,
inlined from ‘copy_from_user’ at ./include/linux/uaccess.h:183:7,
inlined from ‘_btrfs_ioctl_send’ at fs/btrfs/ioctl.c:4343:9,
inlined from ‘btrfs_ioctl’ at fs/btrfs/ioctl.c:4658:10:
./include/linux/kasan-checks.h:38:27: warning: ‘args32’ may be used
uninitialized [-Wmaybe-uninitialized]
38 | #define kasan_check_write __kasan_check_write
./include/linux/instrumented.h:129:9: note: in expansion of macro
‘kasan_check_write’
129 | kasan_check_write(to, n);
| ^~~~~~~~~~~~~~~~~
./include/linux/kasan-checks.h: In function ‘btrfs_ioctl’:
./include/linux/kasan-checks.h:20:6: note: by argument 1 of type ‘const
volatile void *’ to ‘__kasan_check_write’ declared here
20 | bool __kasan_check_write(const volatile void *p, unsigned int
size);
| ^~~~~~~~~~~~~~~~~~~
fs/btrfs/ioctl.c:4341:49: note: ‘args32’ declared here
4341 | struct btrfs_ioctl_send_args_32 args32;
| ^~~~~~
This was due to his config options and having KASAN turned on,
which adds some extra checks around copy_from_user(), which then
triggered the -Wmaybe-uninitialized checker for these cases.
Fix the warnings by initializing the different structs we're copying
into.
Reported-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The One Mix 2S is a mini laptop with a 1200x1920 portrait screen
mounted in a landscape oriented clamshell case. Because of the too
generic DMI strings this entry is also doing bios-date matching.
projects / linux-stable / log