Chip outputs are enabled[1] before actual reset is performed[2] which might
cause pin output value to flip flop if previous pin value was set to 1.
Fix that behavior by making sure chip is fully reset before all outputs are
enabled.
Flip-flop can be noticed when module is removed and inserted again and one of
the pins was changed to 1 before removal. 100 microsecond flipping is
noticeable on oscilloscope (100khz SPI bus).
For a properly reset chip - output is enabled around 100 microseconds (on 100khz
SPI bus) later during probing process hence should be irrelevant behavioral
change.
When configuring a hugetlb filesystem via the fsconfig() syscall, there is
a possible NULL dereference in hugetlbfs_fill_super() caused by assigning
NULL to ctx->hstate in hugetlbfs_parse_param() when the requested pagesize
is non valid.
Put the reference count of cache_cred in cachefiles_daemon_unbind() to
fix the problem. And also put cache_cred in cachefiles_add_cache() error
branch to avoid memory leaks.
Fixes: 9ae326a69004 ("CacheFiles: A cache that backs onto a mounted filesystem") CC: stable@vger.kernel.org Signed-off-by: Baokun Li <libaokun1@huawei.com> Link: https://lore.kernel.org/r/20240217081431.796809-1-libaokun1@huawei.com Acked-by: David Howells <dhowells@redhat.com> Reviewed-by: Jingbo Xu <jefflexu@linux.alibaba.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Baokun Li <libaokun1@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MKTME repurposes the high bit of physical address to key id for encryption
key and, even though MAXPHYADDR in CPUID[0x80000008] remains the same,
the valid bits in the MTRR mask register are based on the reduced number
of physical address bits.
detect_tme() in arch/x86/kernel/cpu/intel.c detects TME and subtracts
it from the total usable physical bits, but it is called too late.
Move the call to early_init_intel() so that it is called in setup_arch(),
before MTRRs are setup.
This fixes boot on TDX-enabled systems, which until now only worked with
"disable_mtrr_cleanup". Without the patch, the values written to the
MTRRs mask registers were 52-bit wide (e.g. 0x000fffff_80000800) and
the writes failed; with the patch, the values are 46-bit wide, which
matches the reduced MAXPHYADDR that is shown in /proc/cpuinfo.
Reported-by: Zixi Chen <zixchen@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org Link: https://lore.kernel.org/all/20240131230902.1867092-3-pbonzini%40redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initializing an eMMC that's connected via a 1-bit bus is current failing,
if the HW (DT) informs that 4-bit bus is supported. In fact this is a
regression, as we were earlier capable of falling back to 1-bit mode, when
switching to 4/8-bit bus failed. Therefore, let's restore the behaviour.
Log for Samsung eMMC 5.1 chip connected via 1bit bus (only D0 pin)
Before patch:
[134509.044225] mmc0: switch to bus width 4 failed
[134509.044509] mmc0: new high speed MMC card at address 0001
[134509.054594] mmcblk0: mmc0:0001 BGUF4R 29.1 GiB
[134509.281602] mmc0: switch to bus width 4 failed
[134509.282638] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.282657] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284598] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.284602] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.284609] ldm_validate_partition_table(): Disk read failed.
[134509.286495] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.286500] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.288303] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.288308] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289540] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.289544] Buffer I/O error on dev mmcblk0, logical block 0, async page read
[134509.289553] mmcblk0: unable to read partition table
[134509.289728] mmcblk0boot0: mmc0:0001 BGUF4R 31.9 MiB
[134509.290283] mmcblk0boot1: mmc0:0001 BGUF4R 31.9 MiB
[134509.294577] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[134509.295835] I/O error, dev mmcblk0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[134509.295841] Buffer I/O error on dev mmcblk0, logical block 0, async page read
Initialize the qDMA irqs after the registers are configured so that
interrupts that may have been pending from a primary kernel don't get
processed by the irq handler before it is ready to and cause panic with
the following trace:
The SoC may hang on 16 byte unaligned read transactions by QDMA.
Unaligned read transactions initiated by QDMA may stall in the NOC
(Network On-Chip), causing a deadlock condition. Stalled transactions will
trigger completion timeouts in PCIe controller.
Workaround:
Enable prefetch by setting the source descriptor prefetchable bit
( SD[PF] = 1 ).
Implement this workaround.
Cc: stable@vger.kernel.org Fixes: b092529e0aa0 ("dmaengine: fsl-qdma: Add qDMA controller driver for Layerscape SoCs") Signed-off-by: Peng Ma <peng.ma@nxp.com> Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20240201215007.439503-1-Frank.Li@nxp.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a syzbot report that device name buffers passed to device
replace are not properly checked for string termination which could lead
to a read out of bounds in getname_kernel().
Add a helper that validates both source and target device name buffers.
For devid as the source initialize the buffer to empty string in case
something tries to read it later.
This was originally analyzed and fixed in a different way by Edward Adam
Davis (see links).
It's currently possible to change the mesh ID when the
interface isn't yet in mesh mode, at the same time as
changing it into mesh mode. This leads to an overwrite
of data in the wdev->u union for the interface type it
currently has, causing cfg80211_change_iface() to do
wrong things when switching.
We could probably allow setting an interface to mesh
while setting the mesh ID at the same time by doing a
different order of operations here, but realistically
there's no userspace that's going to do this, so just
disallow changes in iftype when setting mesh ID.
If a directory has a block with only ".__afsXXXX" files in it (from
uncompleted silly-rename), these .__afsXXXX files are skipped but without
advancing the file position in the dir_context. This leads to
afs_dir_iterate() repeating the block again and again.
Fix this by making the code that skips the .__afsXXXX file also manually
advance the file position.
The bq27xxx i2c-client may not have an IRQ, in which case
client->irq will be 0. bq27xxx_battery_i2c_probe() already has
an if (client->irq) check wrapping the request_threaded_irq().
But bq27xxx_battery_i2c_remove() unconditionally calls
free_irq(client->irq) leading to:
[ 190.310742] ------------[ cut here ]------------
[ 190.310843] Trying to free already-free IRQ 0
[ 190.310861] WARNING: CPU: 2 PID: 1304 at kernel/irq/manage.c:1893 free_irq+0x1b8/0x310
Followed by a backtrace when unbinding the driver. Add
an if (client->irq) to bq27xxx_battery_i2c_remove() mirroring
probe() to fix this.
Fixes: 444ff00734f3 ("power: supply: bq27xxx: Fix I2C IRQ race on remove") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20240215155133.70537-1-hdegoede@redhat.com Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gcc-14 notices that the allocation with sizeof(void) on 32-bit architectures
is not enough for a 64-bit phys_addr_t:
drivers/firmware/efi/capsule-loader.c: In function 'efi_capsule_open':
drivers/firmware/efi/capsule-loader.c:295:24: error: allocation of insufficient size '4' for type 'phys_addr_t' {aka 'long long unsigned int'} with size '8' [-Werror=alloc-size]
295 | cap_info->phys = kzalloc(sizeof(void *), GFP_KERNEL);
| ^
In the commit d73ef2d69c0d ("rtnetlink: let rtnl_bridge_setlink checks
IFLA_BRIDGE_MODE length"), an adjustment was made to the old loop logic
in the function `rtnl_bridge_setlink` to enable the loop to also check
the length of the IFLA_BRIDGE_MODE attribute. However, this adjustment
removed the `break` statement and led to an error logic of the flags
writing back at the end of this function.
if (have_flags)
memcpy(nla_data(attr), &flags, sizeof(flags));
// attr should point to IFLA_BRIDGE_FLAGS NLA !!!
Before the mentioned commit, the `attr` is granted to be IFLA_BRIDGE_FLAGS.
However, this is not necessarily true fow now as the updated loop will let
the attr point to the last NLA, even an invalid NLA which could cause
overflow writes.
This patch introduces a new variable `br_flag` to save the NLA pointer
that points to IFLA_BRIDGE_FLAGS and uses it to resolve the mentioned
error logic.
Fixes: d73ef2d69c0d ("rtnetlink: let rtnl_bridge_setlink checks IFLA_BRIDGE_MODE length") Signed-off-by: Lin Ma <linma@zju.edu.cn> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20240227121128.608110-1-linma@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit d0009effa886 ("netfilter: nf_tables: validate NFPROTO_* family") added
some validation of NFPROTO_* families in the nft_compat module, but it broke
the ability to use legacy iptables modules in dual-stack nftables.
While with legacy iptables one had to independently manage IPv4 and IPv6
tables, with nftables it is possible to have dual-stack tables sharing the
rules. Moreover, it was possible to use rules based on legacy iptables
match/target modules in dual-stack nftables.
As an example, the program from [2] creates an INET dual-stack family table
using an xt_bpf based rule, which looks like the following (the actual output
was generated with a patched nft tool as the current nft tool does not parse
dual stack tables with legacy match rules, so consider it for illustrative
purposes only):
After d0009effa886 ("netfilter: nf_tables: validate NFPROTO_* family") we get
EOPNOTSUPP for the above program.
Fix this by allowing NFPROTO_INET for nft_(match/target)_validate(), but also
restrict the functions to classic iptables hooks.
Changes in v3:
* clarify that upstream nft will not display such configuration properly and
that the output was generated with a patched nft tool
* remove example program from commit description and link to it instead
* no code changes otherwise
Changes in v2:
* restrict nft_(match/target)_validate() to classic iptables hooks
* rewrite example program to use unmodified libnftnl
Right now Linux BT stack cannot pass test case "GAP/CONN/CPUP/BV-05-C
'Connection Parameter Update Procedure Invalid Parameters Central
Responder'" in Bluetooth Test Suite revision GAP.TS.p44. [0]
That was revoled by commit c49a8682fc5d ("Bluetooth: validate BLE
connection interval updates"), but later got reverted due to devices
like keyboards and mice may require low connection interval.
So only validate the max value connection interval to pass the Test
Suite, and let devices to request low connection interval if needed.
If we received HCI_EV_IO_CAPA_REQUEST while
HCI_OP_READ_REMOTE_EXT_FEATURES is yet to be responded assume the remote
does support SSP since otherwise this event shouldn't be generated.
While handling the HCI_EV_HARDWARE_ERROR event, if the underlying
BT controller is not responding, the GPIO reset mechanism would
free the hci_dev and lead to a use-after-free in hci_error_reset.
Here's the call trace observed on a ChromeOS device with Intel AX201:
queue_work_on+0x3e/0x6c
__hci_cmd_sync_sk+0x2ee/0x4c0 [bluetooth <HASH:3b4a6>]
? init_wait_entry+0x31/0x31
__hci_cmd_sync+0x16/0x20 [bluetooth <HASH:3b4a 6>]
hci_error_reset+0x4f/0xa4 [bluetooth <HASH:3b4a 6>]
process_one_work+0x1d8/0x33f
worker_thread+0x21b/0x373
kthread+0x13a/0x152
? pr_cont_work+0x54/0x54
? kthread_blkcg+0x31/0x31
ret_from_fork+0x1f/0x30
This patch holds the reference count on the hci_dev while processing
a HCI_EV_HARDWARE_ERROR event to avoid potential crash.
Fixes: c7741d16a57c ("Bluetooth: Perform a power cycle when receiving hardware error event") Signed-off-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MII code does not check the return value of mdio_read (among
others), and therefore no error code should be sent. A previous fix to
the use of an uninitialized variable propagates negative error codes,
that might lead to wrong operations by the MII library.
An example of such issues is the use of mii_nway_restart by the dm9601
driver. The mii_nway_restart function does not check the value returned
by mdio_read, which in this case might be a negative number which could
contain the exact bit the function checks (BMCR_ANENABLE = 0x1000).
Return zero in case of error, as it is common practice in users of
mdio_read to avoid wrong uses of the return value.
Fixes: 8f8abb863fa5 ("net: usb: dm9601: fix uninitialized variable use in dm9601_mdio_read") Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Peter Korsgaard <peter@korsgaard.com> Link: https://lore.kernel.org/r/20240225-dm9601_ret_err-v1-1-02c1d959ea59@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Same as LAN7800, LAN7850 can be used without EEPROM. If EEPROM is not
present or not flashed, LAN7850 will fail to sync the speed detected by the PHY
with the MAC. In case link speed is 100Mbit, it will accidentally work,
otherwise no data can be transferred.
Better way would be to implement link_up callback, or set auto speed
configuration unconditionally. But this changes would be more intrusive.
So, for now, set it only if no EEPROM is found.
Fixes: e69647a19c87 ("lan78xx: Set ASD in MAC_CR when EEE is enabled.") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/r/20240222123839.2816561-1-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It seems that if userspace provides a correct IFA_TARGET_NETNSID value
but no IFA_ADDRESS and IFA_LOCAL attributes, inet6_rtm_getaddr()
returns -EINVAL with an elevated "struct net" refcount.
Fixes: 6ecf4c37eb3e ("ipv6: enable IFA_TARGET_NETNSID for RTM_GETADDR") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Ahern <dsahern@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The splat occurs because skb->data points past skb->head allocated area.
This is because neigh layer does:
__skb_pull(skb, skb_network_offset(skb));
... but skb_network_offset() returns a negative offset and __skb_pull()
arg is unsigned. IOW, we skb->data gets "adjusted" by a huge value.
The negative value is returned because skb->head and skb->data distance is
more than 64k and skb->network_header (u16) has wrapped around.
The bug is in the ip_tunnel infrastructure, which can cause
dev->needed_headroom to increment ad infinitum.
The syzkaller reproducer consists of packets getting routed via a gre
tunnel, and route of gre encapsulated packets pointing at another (ipip)
tunnel. The ipip encapsulation finds gre0 as next output device.
This results in the following pattern:
1). First packet is to be sent out via gre0.
Route lookup found an output device, ipip0.
2).
ip_tunnel_xmit for gre0 bumps gre0->needed_headroom based on the future
output device, rt.dev->needed_headroom (ipip0).
3).
ip output / start_xmit moves skb on to ipip0. which runs the same
code path again (xmit recursion).
4).
Routing step for the post-gre0-encap packet finds gre0 as output device
to use for ipip0 encapsulated packet.
tunl0->needed_headroom is then incremented based on the (already bumped)
gre0 device headroom.
This repeats for every future packet:
gre0->needed_headroom gets inflated because previous packets' ipip0 step
incremented rt->dev (gre0) headroom, and ipip0 incremented because gre0
needed_headroom was increased.
For each subsequent packet, gre/ipip0->needed_headroom grows until
post-expand-head reallocations result in a skb->head/data distance of
more than 64k.
Once that happens, skb->network_header (u16) wraps around when
pskb_expand_head tries to make sure that skb_network_offset() is unchanged
after the headroom expansion/reallocation.
After this skb_network_offset(skb) returns a different (and negative)
result post headroom expansion.
The next trip to neigh layer (or anything else that would __skb_pull the
network header) makes skb->data point to a memory location outside
skb->head area.
v2: Cap the needed_headroom update to an arbitarily chosen upperlimit to
prevent perpetual increase instead of dropping the headroom increment
completely.
Reported-and-tested-by: syzbot+bfde3bef047a81b8fde6@syzkaller.appspotmail.com Closes: https://groups.google.com/g/syzkaller-bugs/c/fL9G6GtWskY/m/VKk_PR5FBAAJ Fixes: 243aad830e8a ("ip_gre: include route header_len in max_headroom calculation") Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240220135606.4939-1-fw@strlen.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported the following uninit-value access issue [1]:
netlink_to_full_skb() creates a new `skb` and puts the `skb->data`
passed as a 1st arg of netlink_to_full_skb() onto new `skb`. The data
size is specified as `len` and passed to skb_put_data(). This `len`
is based on `skb->end` that is not data offset but buffer offset. The
`skb->end` contains data and tailroom. Since the tailroom is not
initialized when the new `skb` created, KMSAN detects uninitialized
memory area when copying the data.
This patch resolved this issue by correct the len from `skb->end` to
`skb->len`, which is the actual data offset.
When waiting for a syncobj timeline point whose fence has not yet been
submitted with the WAIT_FOR_SUBMIT flag, a callback is registered using
drm_syncobj_fence_add_wait and the thread is put to sleep until the
timeout expires. If the fence is submitted before then,
drm_syncobj_add_point will wake up the sleeping thread immediately which
will proceed to wait for the fence to be signaled.
However, if the WAIT_AVAILABLE flag is used instead,
drm_syncobj_fence_add_wait won't get called, meaning the waiting thread
will always sleep for the full timeout duration, even if the fence gets
submitted earlier. If it turns out that the fence *has* been submitted
by the time it eventually wakes up, it will still indicate to userspace
that the wait completed successfully (it won't return -ETIME), but it
will have taken much longer than it should have.
To fix this, we must call drm_syncobj_fence_add_wait if *either* the
WAIT_FOR_SUBMIT flag or the WAIT_AVAILABLE flag is set. The only
difference being that with WAIT_FOR_SUBMIT we will also wait for the
fence to be signaled after it has been submitted while with
WAIT_AVAILABLE we will return immediately.
IGT test patch: https://lists.freedesktop.org/archives/igt-dev/2024-January/067537.html
Fixes: 01d6c3578379 ("drm/syncobj: add support for timeline point wait v8") Signed-off-by: Erik Kurzinger <ekurzinger@nvidia.com> Signed-off-by: Simon Ser <contact@emersion.fr> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Reviewed-by: Simon Ser <contact@emersion.fr> Link: https://patchwork.freedesktop.org/patch/msgid/20240119163208.3723457-1-ekurzinger@nvidia.com Signed-off-by: Sasha Levin <sashal@kernel.org>
DRM_SYNCOBJ_WAIT_FLAGS_WAIT_FOR_SUBMIT can't be used when we hold locks
since we are basically waiting for userspace to do something.
Holding a lock while doing so can trivial deadlock with page faults
etc...
So make lockdep complain when a driver tries to do this.
v2: Add lockdep_assert_none_held() macro.
v3: Add might_sleep() and also use lockdep_assert_none_held() in the
IOCTL path.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://patchwork.freedesktop.org/patch/414944/
Stable-dep-of: 3c43177ffb54 ("drm/syncobj: call drm_syncobj_fence_add_wait when WAIT_AVAILABLE flag is set") Signed-off-by: Sasha Levin <sashal@kernel.org>
If we have a non-DATA record on the rx_list and another record of the
same type still on the queue, we will end up merging them:
- process_rx_list copies the non-DATA record
- we start the loop and process the first available record since it's
of the same type
- we break out of the loop since the record was not DATA
Just check the record type and jump to the end in case process_rx_list
did some work.
Pointless else branch after goto makes the code harder to refactor
down the line.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fdfbaec5923d ("tls: stop recv() if initial process_rx_list gave us non-DATA") Signed-off-by: Sasha Levin <sashal@kernel.org>
'recv_end:' checks num_async and decrypted, and is then followed
by the 'end' label. Since we know that decrypted and num_async
are 0 at the start we can jump to 'end'.
Move the init of decrypted and num_async to let the compiler
catch if I'm wrong.
Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fdfbaec5923d ("tls: stop recv() if initial process_rx_list gave us non-DATA") Signed-off-by: Sasha Levin <sashal@kernel.org>
The signature for __iowrite64_copy() requires the number of 64 bit
quantities, not bytes. Multiple by 8 to get to a byte length before
invoking zpci_memcpy_toio()
Fixes: 87bc359b9822 ("s390/pci: speed up __iowrite64_copy by using pci store block insn") Acked-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Link: https://lore.kernel.org/r/0-v1-9223d11a7662+1d7785-s390_iowrite64_jgg@nvidia.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
The pernet operations structure for the subsystem must be registered
before registering the generic netlink family.
Fixes: 915d7e5e5930 ("ipv6: sr: add code base for control plane support of SR-IPv6") Signed-off-by: Vasiliy Kovalev <kovalev@altlinux.org> Link: https://lore.kernel.org/r/20240215202717.29815-1-kovalev@altlinux.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
net->dev_base_seq and ipv6.dev_addr_genid are monotonically increasing.
If we XOR their values, we could miss to detect if both values
were changed with the same amount.
Fixes: 63998ac24f83 ("ipv6: provide addr and netconf dump consistency info") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
net->dev_base_seq and ipv4.dev_addr_genid are monotonically increasing.
If we XOR their values, we could miss to detect if both values
were changed with the same amount.
Fixes: 0465277f6b3f ("ipv4: provide addr and netconf dump consistency info") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang-16 warns about casting between incompatible function types:
drivers/gpu/drm/nouveau/nvkm/subdev/bios/shadow.c:161:10: error: cast from 'void (*)(const struct firmware *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
161 | .fini = (void(*)(void *))release_firmware,
This one was done to use the generic shadow_fw_release() function as a
callback for struct nvbios_source. Change it to use the same prototype
as the other five instances, with a trivial helper function that actually
calls release_firmware.
JAZZ_ESP is a bool kconfig symbol that selects SCSI_SPI_ATTRS. When
CONFIG_SCSI=m, this results in SCSI_SPI_ATTRS=m while JAZZ_ESP=y, which
causes many undefined symbol linker errors.
Fix this by only offering to build this driver when CONFIG_SCSI=y.
[mkp: JAZZ_ESP is unique in that it does not support being compiled as a
module unlike the remaining SPI SCSI HBA drivers]
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20240214055953.9612-1-rdunlap@infradead.org Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: linux-mips@vger.kernel.org Cc: Arnd Bergmann <arnd@arndb.de> Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Nicolas Schier <nicolas@fjasle.eu> Cc: James E.J. Bottomley <jejb@linux.ibm.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: linux-scsi@vger.kernel.org Cc: Geert Uytterhoeven <geert@linux-m68k.org> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202402112222.Gl0udKyU-lkp@intel.com/ Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bpf_doc script refers to the GPL as the "GNU Privacy License".
I strongly suspect that the author wanted to refer to the GNU General
Public License, under which the Linux kernel is released, as, to the
best of my knowledge, there is no license named "GNU Privacy License".
This patch corrects the license name in the script accordingly.
Fixes: 56a092c89505 ("bpf: add script and prepare bpf.h for new helpers documentation") Signed-off-by: Gianmarco Lusvardi <glusvardi@posteo.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Quentin Monnet <quentin@isovalent.com> Link: https://lore.kernel.org/bpf/20240213230544.930018-3-glusvardi@posteo.net Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the session name by itself is not sufficient to uniquely identify a
queue pair, include the queue pair number. Show the ASCII channel state
name instead of the numeric value. This change makes the ib_srpt debug
output more consistent.
When dma_alloc_coherent fails to allocate dd->cr_base[i].va,
init_credit_return should deallocate dd->cr_base and
dd->cr_base[i] that allocated before. Or those resources
would be never freed and a memleak is triggered.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn> Link: https://lore.kernel.org/r/20240112085523.3731720-1-alexious@zju.edu.cn Acked-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a possibility that usb_role_switch device is unregistered before
the user put usb_role_switch. In this case, the user may still want to
get/set_role() since the user can't sense the changes of usb_role_switch.
This will add a flag to show if usb_role_switch is already registered and
avoid unwanted behaviors.
Fixes: fde0aa6c175a ("usb: common: Small class for USB role switches")
cc: stable@vger.kernel.org Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20240129093739.2371530-2-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is observed sometimes when tethering is used over NCM with Windows 11
as host, at some instances, the gadget_giveback has one byte appended at
the end of a proper NTB. When the NTB is parsed, unwrap call looks for
any leftover bytes in SKB provided by u_ether and if there are any pending
bytes, it treats them as a separate NTB and parses it. But in case the
second NTB (as per unwrap call) is faulty/corrupt, all the datagrams that
were parsed properly in the first NTB and saved in rx_list are dropped.
In this case, the giveback is of 1025 bytes and block length is 1024.
The rest 1 byte (which is 0x00) won't be parsed resulting in drop of
all datagrams in rx_list.
Same is case with packets of size 2048:
[002] d..1 7828.557948: dwc3_gadget_giveback: ep1out:
req 0000000011dfd96e length 2049/16384 zsI ==> 0
[002] d..1 7828.557949: ncm_unwrap_ntb: K: ncm_unwrap_ntb nth: 1751999342
[002] d..1 7828.557950: ncm_unwrap_ntb: K: ncm_unwrap_ntb blk_len: 0x800
Lecroy shows one byte coming in extra confirming that the byte is coming
in from PC:
According to Windows driver, no ZLP is needed if wBlockLength is non-zero,
because the non-zero wBlockLength has already told the function side the
size of transfer to be expected. However, there are in-market NCM devices
that rely on ZLP as long as the wBlockLength is multiple of wMaxPacketSize.
To deal with such devices, it pads an extra 0 at end so the transfer is no
longer multiple of wMaxPacketSize.
Driver append an additional zero packet request when queue a packet, which
length mod max packet size is 0. When transfer complete, run to line 831,
usb_gadget_giveback_request() will free this requestion. 836 condition is
true, so cdns3_gadget_ep_free_request() free this request again.
Add check at line 829, skip call usb_gadget_giveback_request() if it is
additional zero length packet request. Needn't call
usb_gadget_giveback_request() because it is allocated in this driver.
Cc: stable@vger.kernel.org Fixes: 7733f6c32e36 ("usb: cdns3: Add Cadence USB3 DRD Driver") Signed-off-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Roger Quadros <rogerq@kernel.org> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20240202154217.661867-2-Frank.Li@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without the terminator, if a con_id is passed to gpio_find() that
does not exist in the lookup table the function will not stop looping
correctly, and eventually cause an oops.
Cc: stable@vger.kernel.org Fixes: b2e63555592f ("i2c: gpio: Convert to use descriptors") Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com> Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Link: https://lore.kernel.org/r/20240205102337.439002-1-alexander.sverdlin@gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
l2tp_ip6_sendmsg needs to avoid accounting for the transport header
twice when splicing more data into an already partially-occupied skbuff.
To manage this, we check whether the skbuff contains data using
skb_queue_empty when deciding how much data to append using
ip6_append_data.
However, the code which performed the calculation was incorrect:
ulen = len + skb_queue_empty(&sk->sk_write_queue) ? transhdrlen : 0;
...due to C operator precedence, this ends up setting ulen to
transhdrlen for messages with a non-zero length, which results in
corrupted packets on the wire.
Add parentheses to correct the calculation in line with the original
intent.
Fixes: 9d4c75800f61 ("ipv4, ipv6: Fix handling of transhdrlen in __ip{,6}_append_data()") Cc: David Howells <dhowells@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Tom Parkin <tparkin@katalix.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240220122156.43131-1-tparkin@katalix.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While calculating the hardware interrupt number for a MSI interrupt, the
higher bits (i.e. from bit-5 onwards a.k.a domain_nr >= 32) of the PCI
domain number gets truncated because of the shifted value casting to return
type of pci_domain_nr() which is 'int'. This for example is resulting in
same hardware interrupt number for devices 0019:00:00.0 and 0039:00:00.0.
To address this cast the PCI domain number to 'irq_hw_number_t' before left
shifting it to calculate the hardware interrupt number.
Please note that this fixes the issue only on 64-bit systems and doesn't
change the behavior for 32-bit systems i.e. the 32-bit systems continue to
have the issue. Since the issue surfaces only if there are too many PCIe
controllers in the system which usually is the case in modern server
systems and they don't tend to run 32-bit kernels.
Fixes: 3878eaefb89a ("PCI/MSI: Enhance core to support hierarchy irqdomain") Signed-off-by: Vidya Sagar <vidyas@nvidia.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Shanker Donthineni <sdonthineni@nvidia.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240115135649.708536-1-vidyas@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was said that authenticated encryption could produce invalid tag when
the data that is being encrypted is modified [1]. So, fix this problem by
copying the data into the clone bio first and then encrypt them inside the
clone bio.
This may reduce performance, but it is needed to prevent the user from
corrupting the device by writing data with O_DIRECT and modifying them at
the same time.
Unfortunately the commit `fd8958efe877` introduced another error
causing the `descs` array to overflow. This reults in further crashes
easily reproducible by `sendmsg` system call.
If an SDMA send consists of exactly 6 descriptors and requires dword
padding (in the 7th descriptor), the sdma_txreq descriptor array is not
properly expanded and the packet will overflow into the container
structure. This results in a panic when the send completion runs. The
exact panic varies depending on what elements of the container structure
get corrupted. The fix is to use the correct expression in
_pad_sdma_tx_descs() to test the need to expand the descriptor array.
With this patch the crashes are no longer reproducible and the machine is
stable.
The smem-state properties for the pronto node were incorrectly labelled,
reading `qcom,state*` rather than `qcom,smem-state*`. Fix that, allowing
the stop state to be used.
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
For filesystems with block size < page size, we need to set all the
per-block uptodate bits if the page was already uptodate at the time
we create the per-block metadata. This can happen if the page is
invalidated (eg by a write to drop_caches) but ultimately not removed
from the page cache.
This is a data corruption issue as page writeback skips blocks which
are marked !uptodate.
Fixes: 9dc55f1389f9 ("iomap: add support for sub-pagesize buffered I/O without buffer heads") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reported-by: Qian Cai <cai@redhat.com> Cc: Brian Foster <bfoster@redhat.com> Reviewed-by: Gao Xiang <hsiangkao@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
__bio_for_each_segment assumes that the first struct bio_vec argument
doesn't change - it calls "bio_advance_iter_single((bio), &(iter),
(bvl).bv_len)" to advance the iterator. Unfortunately, the dm-integrity
code changes the bio_vec with "bv.bv_len -= pos". When this code path
is taken, the iterator would be out of sync and dm-integrity would
report errors. This happens if the machine is out of memory and
"kmalloc" fails.
Fix this bug by making a copy of "bv" and changing the copy instead.
Fei has reported that KASAN triggers during apply_alternatives() on
a 5-level paging machine:
BUG: KASAN: out-of-bounds in rcu_is_watching()
Read of size 4 at addr ff110003ee6419a0 by task swapper/0/0
...
__asan_load4()
rcu_is_watching()
trace_hardirqs_on()
text_poke_early()
apply_alternatives()
...
On machines with 5-level paging, cpu_feature_enabled(X86_FEATURE_LA57)
gets patched. It includes KASAN code, where KASAN_SHADOW_START depends on
__VIRTUAL_MASK_SHIFT, which is defined with cpu_feature_enabled().
KASAN gets confused when apply_alternatives() patches the
KASAN_SHADOW_START users. A test patch that makes KASAN_SHADOW_START
static, by replacing __VIRTUAL_MASK_SHIFT with 56, works around the issue.
Fix it for real by disabling KASAN while the kernel is patching alternatives.
[ mingo: updated the changelog ]
Fixes: 6657fca06e3f ("x86/mm: Allow to boot without LA57 if CONFIG_X86_5LEVEL=y") Reported-by: Fei Yang <fei.yang@intel.com> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20231012100424.1456-1-kirill.shutemov@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not try to allocate any amount of memory requested by the user.
Instead limit it to 128 registers. Actually the longest series of
consecutive allowed registers are 48, mmGB_TILE_MODE0-31 and
mmGB_MACROTILE_MODE0-15 (0x2644-0x2673).
The original commit adds a start parameter to the calculation of the
start delay according to some old BSP versions from Allwinner. However,
there're two ways to add this delay -- add it in DSI controller or add
it in the TCON. Add it in both controllers won't work.
The code before this commit is picked from new versions of BSP kernel,
which has a comment for the 1 that says "put start_delay to tcon". By
checking the sun4i_tcon0_mode_set_cpu() in sun4i_tcon driver, it has
already added this delay, so we shouldn't repeat to add the delay in DSI
controller, otherwise the timing won't match.
Some architectures have strict alignment requirements. In that case,
the BPF verifier detects if a program has unaligned accesses and
rejects them. A user can pass BPF_F_ANY_ALIGNMENT to a program to
override this check. That, however, will only work when a privileged
user loads a program. An unprivileged user loading a program with this
flag will be rejected prior entering the verifier.
Hence, it does not make sense to load unprivileged programs without
strict alignment when testing the verifier. This patch avoids exactly
that.
We need to clear all of the bridge private skb variables as they can be
stale due to the packet being recirculated through the stack and then
transmitted through the bridge device. Similar memset is already done on
bridge's input. We've seen cases where proxyarp_replied was 1 on routed
multicast packets transmitted through the bridge to ports with neigh
suppress which were getting dropped. Same thing can in theory happen with
the port isolation bit as well.
Fixes: 821f1b21cabb ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
'status' is known to be 0 at this point. The expected error code is
PTR_ERR(clk).
Switch to dev_err_probe() in order to display the expected error code (in a
human readable way).
This also filters -EPROBE_DEFER cases, should it happen.
of_find_node_by_phandle() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak.
Demote headers which are clearly not kerneldoc, provide titles for
struct definition blocks, fix API slip (bitrot) misspellings and
provide some missing entries.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/pinctrl-rockchip.c:82: warning: cannot understand function prototype: 'struct rockchip_iomux '
drivers/pinctrl/pinctrl-rockchip.c:97: warning: Enum value 'DRV_TYPE_IO_DEFAULT' not described in enum 'rockchip_pin_drv_type'
drivers/pinctrl/pinctrl-rockchip.c:97: warning: Enum value 'DRV_TYPE_IO_1V8_OR_3V0' not described in enum 'rockchip_pin_drv_type'
drivers/pinctrl/pinctrl-rockchip.c:97: warning: Enum value 'DRV_TYPE_IO_1V8_ONLY' not described in enum 'rockchip_pin_drv_type'
drivers/pinctrl/pinctrl-rockchip.c:97: warning: Enum value 'DRV_TYPE_IO_1V8_3V0_AUTO' not described in enum 'rockchip_pin_drv_type'
drivers/pinctrl/pinctrl-rockchip.c:97: warning: Enum value 'DRV_TYPE_IO_3V3_ONLY' not described in enum 'rockchip_pin_drv_type'
drivers/pinctrl/pinctrl-rockchip.c:97: warning: Enum value 'DRV_TYPE_MAX' not described in enum 'rockchip_pin_drv_type'
drivers/pinctrl/pinctrl-rockchip.c:106: warning: Enum value 'PULL_TYPE_IO_DEFAULT' not described in enum 'rockchip_pin_pull_type'
drivers/pinctrl/pinctrl-rockchip.c:106: warning: Enum value 'PULL_TYPE_IO_1V8_ONLY' not described in enum 'rockchip_pin_pull_type'
drivers/pinctrl/pinctrl-rockchip.c:106: warning: Enum value 'PULL_TYPE_MAX' not described in enum 'rockchip_pin_pull_type'
drivers/pinctrl/pinctrl-rockchip.c:109: warning: Cannot understand * @drv_type: drive strength variant using rockchip_perpin_drv_type
on line 109 - I thought it was a doc line
drivers/pinctrl/pinctrl-rockchip.c:122: warning: Cannot understand * @reg_base: register base of the gpio bank
on line 109 - I thought it was a doc line
drivers/pinctrl/pinctrl-rockchip.c:325: warning: Function parameter or member 'route_location' not described in 'rockchip_mux_route_data'
drivers/pinctrl/pinctrl-rockchip.c:328: warning: Cannot understand */
on line 109 - I thought it was a doc line
drivers/pinctrl/pinctrl-rockchip.c:375: warning: Function parameter or member 'data' not described in 'rockchip_pin_group'
drivers/pinctrl/pinctrl-rockchip.c:387: warning: Function parameter or member 'ngroups' not described in 'rockchip_pmx_func'
Now sk->sk_shutdown is no longer a bitfield, we can add
standard READ_ONCE()/WRITE_ONCE() annotations to silence
KCSAN reports like the following:
BUG: KCSAN: data-race in tcp_disconnect / tcp_poll
write to 0xffff88814588582c of 1 bytes by task 3404 on cpu 1:
tcp_disconnect+0x4d6/0xdb0 net/ipv4/tcp.c:3121
__inet_stream_connect+0x5dd/0x6e0 net/ipv4/af_inet.c:715
inet_stream_connect+0x48/0x70 net/ipv4/af_inet.c:727
__sys_connect_file net/socket.c:2001 [inline]
__sys_connect+0x19b/0x1b0 net/socket.c:2018
__do_sys_connect net/socket.c:2028 [inline]
__se_sys_connect net/socket.c:2025 [inline]
__x64_sys_connect+0x41/0x50 net/socket.c:2025
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
read to 0xffff88814588582c of 1 bytes by task 3374 on cpu 0:
tcp_poll+0x2e6/0x7d0 net/ipv4/tcp.c:562
sock_poll+0x253/0x270 net/socket.c:1383
vfs_poll include/linux/poll.h:88 [inline]
io_poll_check_events io_uring/poll.c:281 [inline]
io_poll_task_func+0x15a/0x820 io_uring/poll.c:333
handle_tw_list io_uring/io_uring.c:1184 [inline]
tctx_task_work+0x1fe/0x4d0 io_uring/io_uring.c:1246
task_work_run+0x123/0x160 kernel/task_work.c:179
get_signal+0xe64/0xff0 kernel/signal.c:2635
arch_do_signal_or_restart+0x89/0x2a0 arch/x86/kernel/signal.c:306
exit_to_user_mode_loop+0x6f/0xe0 kernel/entry/common.c:168
exit_to_user_mode_prepare+0x6c/0xb0 kernel/entry/common.c:204
__syscall_exit_to_user_mode_work kernel/entry/common.c:286 [inline]
syscall_exit_to_user_mode+0x26/0x140 kernel/entry/common.c:297
do_syscall_64+0x4d/0xc0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x03 -> 0x00
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If there was any event available on the TCP socket, tcp_poll()
will be called to retrieve all the events. In tcp_poll(), we call
sk_stream_is_writeable() which returns true as long as we are at least
one byte below notsent_lowat. This will result in quite a few
spurious EPLLOUT and frequent tiny sendmsg() calls as a result.
Similar to sk_stream_write_space(), use __sk_stream_is_writeable
with a wake value of 1, so that we set EPOLLOUT only if half the
space is available for write.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The power domain containing the Cortex-R7 CPU core on the R-Car V3H SoC
must always be in power-on state, unlike on other SoCs in the R-Car Gen3
family. See Table 9.4 "Power domains" in the R-Car Series, 3rd
Generation Hardware User’s Manual Rev.1.00 and later.
Fix this by marking the domain as a CPU domain without control
registers, so the driver will not touch it.
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834df ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Cc: stable@vger.kernel.org Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure no remaining requests in virtqueues before resetting vdev and
deleting virtqueues. Otherwise these requests will never be completed.
It may cause the system to become unresponsive.
Function blk_mq_quiesce_queue() can ensure that requests have become
in_flight status, but it cannot guarantee that requests have been
processed by the device. Virtqueues should never be deleted before
all requests become complete status.
Function blk_mq_freeze_queue() ensure that all requests in virtqueues
become complete status. And no requests can enter in virtqueues.
If we are bus manager and the bus has inconsistent gap counts, send a
bus reset immediately instead of trying to read the root node's config
ROM first. Otherwise, we could spend a lot of time trying to read the
config ROM but never succeeding.
This eliminates a 50+ second delay before the FireWire bus is usable after
a newly connected device is powered on in certain circumstances.
The delay occurs if a gap count inconsistency occurs, we are not the root
node, and we become bus manager. One scenario that causes this is with a TI
XIO2213B OHCI, the first time a Sony DSR-25 is powered on after being
connected to the FireWire cable. In this configuration, the Linux box will
not receive the initial PHY configuration packet sent by the DSR-25 as IRM,
resulting in the DSR-25 having a gap count of 44 while the Linux box has a
gap count of 63.
FireWire devices have a gap count parameter, which is set to 63 on power-up
and can be changed with a PHY configuration packet. This determines the
duration of the subaction and arbitration gaps. For reliable communication,
all nodes on a FireWire bus must have the same gap count.
A node may have zero or more of the following roles: root node, bus manager
(BM), isochronous resource manager (IRM), and cycle master. Unless a root
node was forced with a PHY configuration packet, any node might become root
node after a bus reset. Only the root node can become cycle master. If the
root node is not cycle master capable, the BM or IRM should force a change
of root node.
After a bus reset, each node sends a self-ID packet, which contains its
current gap count. A single bus reset does not change the gap count, but
two bus resets in a row will set the gap count to 63. Because a consistent
gap count is required for reliable communication, IEEE 1394a-2000 requires
that the bus manager generate a bus reset if it detects that the gap count
is inconsistent.
When the gap count is inconsistent, build_tree() will notice this after the
self identification process. It will set card->gap_count to the invalid
value 0. If we become bus master, this will force bm_work() to send a bus
reset when it performs gap count optimization.
After a bus reset, there is no bus manager. We will almost always try to
become bus manager. Once we become bus manager, we will first determine
whether the root node is cycle master capable. Then, we will determine if
the gap count should be changed. If either the root node or the gap count
should be changed, we will generate a bus reset.
To determine if the root node is cycle master capable, we read its
configuration ROM. bm_work() will wait until we have finished trying to
read the configuration ROM.
However, an inconsistent gap count can make this take a long time.
read_config_rom() will read the first few quadlets from the config ROM. Due
to the gap count inconsistency, eventually one of the reads will time out.
When read_config_rom() fails, fw_device_init() calls it again until
MAX_RETRIES is reached. This takes 50+ seconds.
Once we give up trying to read the configuration ROM, bm_work() will wake
up, assume that the root node is not cycle master capable, and do a bus
reset. Hopefully, this will resolve the gap count inconsistency.
This change makes bm_work() check for an inconsistent gap count before
waiting for the root node's configuration ROM. If the gap count is
inconsistent, bm_work() will immediately do a bus reset. This eliminates
the 50+ second delay and rapidly brings the bus to a working state.
I considered that if the gap count is inconsistent, a PHY configuration
packet might not be successful, so it could be desirable to skip the PHY
configuration packet before the bus reset in this case. However, IEEE
1394a-2000 and IEEE 1394-2008 say that the bus manager may transmit a PHY
configuration packet before a bus reset when correcting a gap count error.
Since the standard endorses this, I decided it's safe to retain the PHY
configuration packet transmission.
Normally, after a topology change, we will reset the bus a maximum of 5
times to change the root node and perform gap count optimization. However,
if there is a gap count inconsistency, we must always generate a bus reset.
Otherwise the gap count inconsistency will persist and communication will
be unreliable. For that reason, if there is a gap count inconstency, we
generate a bus reset even if we already reached the 5 reset limit.
LUNs going into "failed ready running" state observed on >1T and on even
numbers of size (2T, 4T, 6T, 8T and 10T). The issue occurs when DIF is
enabled at the host.
The kernel logs:
Cannot setup S/G List for HBAIO segs 1/1 SGL 512 SCSI 256: 3 0
The host lpfc driver is failing to setup scatter/gather list (protection
data) for the I/Os.
The return type lpfc_bg_setup_sgl()/lpfc_bg_setup_sgl_prot() causes the
compiler to remove the most significant bit. Use an unsigned type instead.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[dwagner: added commit message] Signed-off-by: Daniel Wagner <dwagner@suse.de> Link: https://lore.kernel.org/r/20231220162658.12392-1-dwagner@suse.de Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, coretemp driver supports only 128 cores per package.
This loses some core temperature information on systems that have more
than 128 cores per package.
[ 58.685033] coretemp coretemp.0: Adding Core 128 failed
[ 58.692009] coretemp coretemp.0: Adding Core 129 failed
...
Enlarge the limitation to 512 because there are platforms with more than
256 cores per package.
When the target port has not active port binding, there is no point in
trying to process the command as it has to fail anyway. Instead adding
checks to all commands abort the command early.
Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The annotation says in sctp_new(): "If it is a shutdown ack OOTB packet, we
expect a return shutdown complete, otherwise an ABORT Sec 8.4 (5) and (8)".
However, it does not check SCTP_CID_SHUTDOWN_ACK before setting vtag[REPLY]
in the conntrack entry(ct).
Because of that, if the ct in Router disappears for some reason in [1]
with the packet sequence like below:
when processing HB ACK packet in Router it calls sctp_new() to initialize
the new ct with vtag[REPLY] set to HB_ACK packet's vtag.
Later when sending DATA from Client, all the SACKs from Server will get
dropped in Router, as the SACK packet's vtag does not match vtag[REPLY]
in the ct. The worst thing is the vtag in this ct will never get fixed
by the upcoming packets from Server.
This patch fixes it by checking SCTP_CID_SHUTDOWN_ACK before setting
vtag[REPLY] in the ct in sctp_new() as the annotation says. With this
fix, it will leave vtag[REPLY] in ct to 0 in the case above, and the
next HB REQ/ACK from Server is able to fix the vtag as its value is 0
in nf_conntrack_sctp_packet().
Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Continuous regulators can be configured to operate only in a certain
duty cycle range (for example from 0..91%). Add a check to error out if
the duty cycle translates to an unsupported (or out of range) voltage.
Places the logic for checking if the group's block bitmap is corrupt under
the protection of the group lock to avoid allocating blocks from the group
with a corrupted block bitmap.
Determine if the group block bitmap is corrupted before using ac_b_ex in
ext4_mb_try_best_found() to avoid allocating blocks from a group with a
corrupted block bitmap in the following concurrency and making the
situation worse.
ext4_mb_regular_allocator
ext4_lock_group(sb, group)
ext4_mb_good_group
// check if the group bbitmap is corrupted
ext4_mb_complex_scan_group
// Scan group gets ac_b_ex but doesn't use it
ext4_unlock_group(sb, group)
ext4_mark_group_bitmap_corrupted(group)
// The block bitmap was corrupted during
// the group unlock gap.
ext4_mb_try_best_found
ext4_lock_group(ac->ac_sb, group)
ext4_mb_use_best_found
mb_mark_used
// Allocating blocks in block bitmap corrupted group
With one of the on-board ASM1061 AHCI controllers (1b21:0612) on an
ASUSTeK Pro WS WRX80E-SAGE SE WIFI mainboard, a controller hang was
observed that was immediately preceded by the following kernel
messages:
The first message is produced by code in drivers/iommu/dma-iommu.c
which is accompanied by the following comment that seems to apply:
/*
* Try to use all the 32-bit PCI addresses first. The original SAC vs.
* DAC reasoning loses relevance with PCIe, but enough hardware and
* firmware bugs are still lurking out there that it's safest not to
* venture into the 64-bit space until necessary.
*
* If your device goes wrong after seeing the notice then likely either
* its driver is not setting DMA masks accurately, the hardware has
* some inherent bug in handling >32-bit addresses, or not all the
* expected address bits are wired up between the device and the IOMMU.
*/
Asking the ASM1061 on a discrete PCIe card to DMA from I/O virtual
address 0xffffffff00000000 produces the following I/O page faults:
Note that the upper 21 bits of the logged DMA address are zero. (When
asking a different PCIe device in the same PCIe slot to DMA to the
same I/O virtual address, we do see all the upper 32 bits of the DMA
address as 1, so this is not an issue with the chipset or IOMMU
configuration on the test system.)
Also, hacking libahci to always set the upper 21 bits of all DMA
addresses to 1 produces no discernible effect on the behavior of the
ASM1061, and mkfs/mount/scrub/etc work as without this hack.
This all strongly suggests that the ASM1061 has a 43 bit DMA address
limit, and this commit therefore adds a quirk to deal with this limit.
This issue probably applies to (some of) the other supported ASMedia
parts as well, but we limit it to the PCI IDs known to refer to
ASM1061 parts, as that's the only part we know for sure to be affected
by this issue at this point.
Link: https://lore.kernel.org/linux-ide/ZaZ2PIpEId-rl6jv@wantstofly.org/ Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: drop date from error messages in commit log] Signed-off-by: Niklas Cassel <cassel@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of pixclock,
it may cause divide-by-zero error.
In sisfb_check_var(), var->pixclock is used as a divisor to caculate
drate before it is checked against zero. Fix this by checking it
at the beginning.
This is similar to CVE-2022-3061 in i740fb which was fixed by
commit 15cf0b8.
The userspace program could pass any values to the driver through
ioctl() interface. If the driver doesn't check the value of pixclock,
it may cause divide-by-zero error.
Although pixclock is checked in savagefb_decode_var(), but it is not
checked properly in savagefb_probe(). Fix this by checking whether
pixclock is zero in the function savagefb_check_var() before
info->var.pixclock is used as the divisor.
This is similar to CVE-2022-3061 in i740fb which was fixed by
commit 15cf0b8.
fast-xmit must only be enabled after the sta has been uploaded to the driver,
otherwise it could end up passing the not-yet-uploaded sta via drv_tx calls
to the driver, leading to potential crashes because of uninitialized drv_priv
data.
Add a missing sta->uploaded check and re-check fast xmit after inserting a sta.
dump(cb=[0, 1]):
if_start=cb[1] (=1)
send rdev0.wdev1 -> ok
// since if_start=1 the rdev0.wdev0 got skipped
// through if_idx < if_start
send rdev1.wdev1 -> ok
The if_start needs to be reset back to 0 upon wdev
loop end.
The problem is actually hard to hit on a desktop,
and even on most routers. The prerequisites for
this manifesting was:
- more than 1 wiphy
- a few handful of interfaces
- dump without rdev or wdev filter
I was seeing this with 4 wiphys 9 interfaces each.
It'd miss 6 interfaces from the last wiphy
reported to userspace.
We seem to have hit warnings of 'output may be truncated' which is fixed
by increasing the size of 'irq_name'
drivers/dma/fsl-qdma.c: In function ‘fsl_qdma_irq_init’:
drivers/dma/fsl-qdma.c:824:46: error: ‘%d’ directive writing between 1 and 11 bytes into a region of size 10 [-Werror=format-overflow=]
824 | sprintf(irq_name, "qdma-queue%d", i);
| ^~
drivers/dma/fsl-qdma.c:824:35: note: directive argument in the range [-2147483641, 2147483646]
824 | sprintf(irq_name, "qdma-queue%d", i);
| ^~~~~~~~~~~~~~
drivers/dma/fsl-qdma.c:824:17: note: ‘sprintf’ output between 12 and 22 bytes into a destination of size 20
824 | sprintf(irq_name, "qdma-queue%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We seem to have hit warnings of 'output may be truncated' which is fixed
by increasing the size of 'dev_id'
drivers/dma/sh/shdmac.c: In function ‘sh_dmae_probe’:
drivers/dma/sh/shdmac.c:541:34: error: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 9 [-Werror=format-truncation=]
541 | "sh-dmae%d.%d", pdev->id, id);
| ^~
In function ‘sh_dmae_chan_probe’,
inlined from ‘sh_dmae_probe’ at drivers/dma/sh/shdmac.c:845:9:
drivers/dma/sh/shdmac.c:541:26: note: directive argument in the range [0, 2147483647]
541 | "sh-dmae%d.%d", pdev->id, id);
| ^~~~~~~~~~~~~~
drivers/dma/sh/shdmac.c:541:26: note: directive argument in the range [0, 19]
drivers/dma/sh/shdmac.c:540:17: note: ‘snprintf’ output between 11 and 21 bytes into a destination of size 16
540 | snprintf(sh_chan->dev_id, sizeof(sh_chan->dev_id),
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
541 | "sh-dmae%d.%d", pdev->id, id);
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
An abort that is responded to by iSCSI itself is added to tmr_list but does
not go to target core. A LUN_RESET that goes through tmr_list takes a
refcounter on the abort and waits for completion. However, the abort will
be never complete because it was not started in target core.
Unable to locate ITT: 0x05000000 on CID: 0
Unable to locate RefTaskTag: 0x05000000 on CID: 0.
wait_for_tasks: Stopping tmf LUN_RESET with tag 0x0 ref_task_tag 0x0 i_state 34 t_state ISTATE_PROCESSING refcnt 2 transport_state active,stop,fabric_stop
wait for tasks: tmf LUN_RESET with tag 0x0 ref_task_tag 0x0 i_state 34 t_state ISTATE_PROCESSING refcnt 2 transport_state active,stop,fabric_stop
...
INFO: task kworker/0:2:49 blocked for more than 491 seconds.
task:kworker/0:2 state:D stack: 0 pid: 49 ppid: 2 flags:0x00000800
Workqueue: events target_tmr_work [target_core_mod]
Call Trace:
__switch_to+0x2c4/0x470
_schedule+0x314/0x1730
schedule+0x64/0x130
schedule_timeout+0x168/0x430
wait_for_completion+0x140/0x270
target_put_cmd_and_wait+0x64/0xb0 [target_core_mod]
core_tmr_lun_reset+0x30/0xa0 [target_core_mod]
target_tmr_work+0xc8/0x1b0 [target_core_mod]
process_one_work+0x2d4/0x5d0
worker_thread+0x78/0x6c0
To fix this, only add abort to tmr_list if it will be handled by target
core.
Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com> Link: https://lore.kernel.org/r/20240111125941.8688-1-d.bogdanov@yadro.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The validation of the value written to sched_rt_period_us was broken
because:
- the sysclt_sched_rt_period is declared as unsigned int
- parsed by proc_do_intvec()
- the range is asserted after the value parsed by proc_do_intvec()
Because of this negative values written to the file were written into a
unsigned integer that were later on interpreted as large positive
integers which did passed the check:
if (sysclt_sched_rt_period <= 0)
return EINVAL;
This commit fixes the parsing by setting explicit range for both
perid_us and runtime_us into the sched_rt_sysctls table and processes
the values with proc_dointvec_minmax() instead.
Alternatively if we wanted to use full range of unsigned int for the
period value we would have to split the proc_handler and use
proc_douintvec() for it however even the
Documentation/scheduller/sched-rt-group.rst describes the range as 1 to
INT_MAX.
As far as I can tell the only problem this causes is that the sysctl
file allows writing negative values which when read back may confuse
userspace.
There is also a LTP test being submitted for these sysctl files at:
projects / linux-stable / log