[Why]
ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk
according to bandwidth requirement. call stack: rv1_update_clocks -->
update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth
--> prepare_bandwidth / optimize_bandwidth. before change dcn hw,
prepare_bandwidth will be called first to allow enough clock,
watermark for change, after end of dcn hw change, optimize_bandwidth
is executed to lower clock to save power for new dcn hw settings.
below is sequence of commit_planes_for_stream:
step 1: prepare_bandwidth - raise clock to have enough bandwidth
step 2: lock_doublebuffer_enable
step 3: pipe_control_lock(true) - make dchubp register change will
not take effect right way
step 4: apply_ctx_for_surface - program dchubp
step 5: pipe_control_lock(false) - dchubp register change take effect
step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream
for full_date, optimize clock to save power
at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be
changed for new dchubp configuration. but real dcn hub dchubps are
still running with old configuration until end of step 5. this need
clocks settings at step 1 should not less than that before step 1.
this is checked by two conditions: 1. if (should_set_clock(safe_to_lower
, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) ||
new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz)
2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz
the second condition is based on new dchubp configuration. dppclk
for new dchubp may be different from dppclk before step 1.
for example, before step 1, dchubps are as below:
pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979)
pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080)
for dppclk for pipe0 need dppclk = dispclk
new dchubp pipe split configuration:
pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080)
pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080)
dppclk only needs dppclk = dispclk /2.
dispclk, dppclk are not lock by otg master lock. they take effect
after step 1. during this transition, dispclk are the same, but
dppclk is changed to half of previous clock for old dchubp
configuration between step 1 and step 6. This may cause p-state
warning intermittently.
[How]
for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we
need make sure dppclk are not changed to less between step 1 and 6.
for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz,
new display clock is raised, but we do not know ratio of
new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz,
new_clocks->dispclk_khz /2 does not guarantee equal or higher than
old dppclk. we could ignore power saving different between
dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6.
as long as safe_to_lower = false, set dpclk = dispclk to simplify
condition check.
Reproducing bug report here:
After hibernating and resuming, DPM is not enabled. This remains the case
even if you test hibernate using the steps here:
https://www.kernel.org/doc/html/latest/power/basic-pm-debugging.html
I debugged the problem, and figured out that in the file hardwaremanager.c,
in the function, phm_enable_dynamic_state_management(), the check
'if (!hwmgr->pp_one_vf && smum_is_dpm_running(hwmgr) && !amdgpu_passthrough(adev) && adev->in_suspend)'
returns true for the hibernate case, and false for the suspend case.
This means that for the hibernate case, the AMDGPU driver doesn't enable DPM
(even though it should) and simply returns from that function.
In the suspend case, it goes ahead and enables DPM, even though it doesn't need to.
I debugged further, and found out that in the case of suspend, for the
CIK/Hawaii GPUs, smum_is_dpm_running(hwmgr) returns false, while in the case of
hibernate, smum_is_dpm_running(hwmgr) returns true.
For CIK, the ci_is_dpm_running() function calls the ci_is_smc_ram_running() function,
which is ultimately used to determine if DPM is currently enabled or not,
and this seems to provide the wrong answer.
I've changed the ci_is_dpm_running() function to instead use the same method that
some other AMD GPU chips do (e.g Fiji), which seems to read the voltage controller.
I've tested on my R9 390 and it seems to work correctly for both suspend and
hibernate use cases, and has been stable so far.
drm_dp_mst_allocate_vcpi() invokes
drm_dp_mst_topology_get_port_validated(), which increases the refcount
of the "port".
These reference counting issues take place in two exception handling
paths separately. Either when “slots” is less than 0 or when
drm_dp_init_vcpi() returns a negative value, the function forgets to
reduce the refcnt increased drm_dp_mst_topology_get_port_validated(),
which results in a refcount leak.
Fix these issues by pulling up the error handling when "slots" is less
than 0, and calling drm_dp_mst_topology_put_port() before termination
when drm_dp_init_vcpi() returns a negative value.
Fixes: 1e797f556c61 ("drm/dp: Split drm_dp_mst_allocate_vcpi") Cc: <stable@vger.kernel.org> # v4.12+ Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200719154545.GA41231@xin-virtual-machine Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The connector type for DISPC's DPI videoport was set the LVDS instead of
DPI. This causes any DPI panel setup to fail with tidss, making all DPI
panels unusable.
Fix this by using correct connector type.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Fixes: 32a1795f57eecc39749017 ("drm/tidss: New driver for TI Keystone platform Display SubSystem") Cc: stable@vger.kernel.org # v5.7+ Link: https://patchwork.freedesktop.org/patch/msgid/20200604080214.107159-1-tomi.valkeinen@ti.com Reviewed-by: Jyri Sarha <jsarha@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use SET_LATE_SYSTEM_SLEEP_PM_OPS in DSS submodules to force runtime PM
suspend and resume.
We use suspend late version so that omapdrm's system suspend callback is
called first, as that will disable all the display outputs after which
it's safe to force DSS into suspend.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200618095153.611071-1-tomi.valkeinen@ti.com Acked-by: Tony Lindgren <tony@atomide.com> Fixes: cef766300353 ("drm/omap: Prepare DSS for probing without legacy platform data") Cc: stable@vger.kernel.org # v5.7+ Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Thu, 6 Aug 2020 14:49:39 +0000 (10:49 -0400)]
drm/amdgpu: fix ordering of psp suspend
The ordering of psp_tmr_terminate() and psp_asd_unload()
got reversed when the patches were applied to stable.
This patch does not exist in Linus' tree because the ordering
is correct there. It got reversed when the patches were applied
to stable. This patch is for stable only.
Fixes: 22ff658396b446 ("drm/amdgpu: asd function needs to be unloaded in suspend phase") Fixes: 2c41c968c6f648 ("drm/amdgpu: add TMR destory function for psp") Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org # 5.7.x Cc: Huang Rui <ray.huang@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the initial MST probing an MST port's I2C device will be
registered using the kdev of the DRM device as a parent. Later after MST
Connection Status Notifications this I2C device will be re-registered
with the kdev of the port's connector. This will also move
inconsistently the I2C device's sysfs entry from the DRM device's sysfs
dir to the connector's dir.
Fix the above by keeping the DRM kdev as the parent of the I2C device.
Ideally the connector's kdev would be used as a parent, similarly to
non-MST connectors, however that needs some more refactoring to ensure
the connector's kdev is already available early enough. So keep the
existing (initial) behavior for now.
Before we return control to the system, and letting it reuse all the
pages being accessed by HW, we must disable the HW. At the moment, we
dare not reset the GPU if it will clobber the display, but once we know
the display has been disabled, we can proceed with the reset as we
shutdown the module. We know the next user must reinitialise the HW for
their purpose.
Tegra PMC clock clk_out_1 is dedicated for audio mclk from Tegra30
through Tegra210 and currently Tegra clock driver keeps the audio mclk
enabled.
With the move of PMC clocks from clock driver into pmc driver, audio
mclk enable from clock driver is removed and this should be taken care
of by the audio driver.
tegra_asoc_utils_init() calls tegra_asoc_utils_set_rate() and audio mclk
rate configuration is not needed during init and the rate is actually
set during the ->hw_params() callback.
So, this patch removes tegra_asoc_utils_set_rate() call and just leaves
the audio mclk enabled.
Tegra PMC clock clk_out_1 is dedicated for audio mclk from Tegra30
through Tegra210 and currently Tegra clock driver does the initial
parent configuration for audio mclk and keeps it enabled by default.
With the move of PMC clocks from clock driver into PMC driver, audio
clocks parent configuration can be specified through the device tree
using assigned-clock-parents property and audio mclk control should be
taken care of by the audio driver.
This patch has implementation for parent configuration when default
parent configuration through assigned-clock-parents property is not
specified in the device tree.
tegra_asoc_utils uses clk_get() to get the clock and clk_put() to free
them explicitly.
This patch updates it to use device managed resource API devm_clk_get()
so the clock will be automatically released and freed when the device is
unbound and removes tegra_asoc_utils_fini() as its no longer needed.
Only once have I seen this scenario (and forgot even to notice what forced
the eventual crash): a sequence of "BUG: Bad page map" alerts from
vm_normal_page(), from zap_pte_range() servicing exit_mmap();
pmd:00000000, pte values corresponding to data in physical page 0.
The pte mappings being zapped in this case were supposed to be from a huge
page of ext4 text (but could as well have been shmem): my belief is that
it was racing with collapse_file()'s retract_page_tables(), found *pmd
pointing to a page table, locked it, but *pmd had become 0 by the time
start_pte was decided.
In most cases, that possibility is excluded by holding mmap lock; but
exit_mmap() proceeds without mmap lock. Most of what's run by khugepaged
checks khugepaged_test_exit() after acquiring mmap lock:
khugepaged_collapse_pte_mapped_thps() and hugepage_vma_revalidate() do so,
for example. But retract_page_tables() did not: fix that.
The fix is for retract_page_tables() to check khugepaged_test_exit(),
after acquiring mmap lock, before doing anything to the page table.
Getting the mmap lock serializes with __mmput(), which briefly takes and
drops it in __khugepaged_exit(); then the khugepaged_test_exit() check on
mm_users makes sure we don't touch the page table once exit_mmap() might
reach it, since exit_mmap() will be proceeding without mmap lock, not
expecting anyone to be racing with it.
Fixes: f3f0e1d2150b ("khugepaged: add support of collapse for tmpfs/shmem pages") Signed-off-by: Hugh Dickins <hughd@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Song Liu <songliubraving@fb.com> Cc: <stable@vger.kernel.org> [4.8+] Link: http://lkml.kernel.org/r/alpine.LSU.2.11.2008021215400.27773@eggly.anvils Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Landisk setup code maps the CF IDE area using ioremap_prot(), and
passes the resulting virtual addresses to the pata_platform driver,
disguising them as I/O port addresses. Hence the pata_platform driver
translates them again using ioport_map().
As CONFIG_GENERIC_IOMAP=n, and CONFIG_HAS_IOPORT_MAP=y, the
SuperH-specific mapping code in arch/sh/kernel/ioport.c translates
I/O port addresses to virtual addresses by adding sh_io_port_base, which
defaults to -1, thus breaking the assumption of an identity mapping.
When using a cross-compilation environment, such as OpenEmbedded,
the CC an CXX variables are set to something more than just a
command: there are arguments (such as --sysroot) that need to be
passed on to the compiler so that the right set of headers and
libraries are used.
For the particular case that our systems detected, CC is set to
the following:
Auto-detecting system features:
... dwarf: [ OFF ]
... dwarf_getlocations: [ OFF ]
... glibc: [ OFF ]
... gtk2: [ OFF ]
... libbfd: [ OFF ]
... libcap: [ OFF ]
... libelf: [ OFF ]
... libnuma: [ OFF ]
... numa_num_possible_cpus: [ OFF ]
... libperl: [ OFF ]
... libpython: [ OFF ]
... libcrypto: [ OFF ]
... libunwind: [ OFF ]
... libdw-dwarf-unwind: [ OFF ]
... zlib: [ OFF ]
... lzma: [ OFF ]
... get_cpuid: [ OFF ]
... bpf: [ OFF ]
... libaio: [ OFF ]
... libzstd: [ OFF ]
... disassembler-four-args: [ OFF ]
With CC and CXX quoted, some of those features are now detected.
Fixes: e3232c2f39ac ("tools build feature: Use CC and CXX from parent") Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org> Reviewed-by: Thomas Hebb <tommyhebb@gmail.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Andrii Nakryiko <andriin@fb.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Jiri Olsa <jolsa@kernel.org> Cc: John Fastabend <john.fastabend@gmail.com> Cc: KP Singh <kpsingh@chromium.org> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Cc: Yonghong Song <yhs@fb.com> Link: http://lore.kernel.org/lkml/20200812221518.2869003-1-daniel.diaz@linaro.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For memcpy, the source pages are memset to zero only when --cycles is
used. This leads to wildly different results with or without --cycles,
since all sources pages are likely to be mapped to the same zero page
without explicit writes.
Before this fix:
$ export cmd="./perf stat -e LLC-loads -- ./perf bench \
mem memcpy -s 1024MB -l 100 -f default"
$ $cmd
2,935,826 LLC-loads
3.821677452 seconds time elapsed
$ $cmd --cycles
217,533,436 LLC-loads
8.616725985 seconds time elapsed
After this fix:
$ $cmd
214,459,686 LLC-loads
8.674301124 seconds time elapsed
$ $cmd --cycles
214,758,651 LLC-loads
8.644480006 seconds time elapsed
Fixes: 47b5757bac03c338 ("perf bench mem: Move boilerplate memory allocation to the infrastructure") Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: kernel@axis.com Link: http://lore.kernel.org/lkml/20200810133404.30829-1-vincent.whitchurch@axis.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In skcipher_accept_parent_nokey() the whole af_alg_ctx structure is
cleared by memset() after allocation, so add such memset() also to
aead_accept_parent_nokey() so that the new "init" field is also
initialized to zero. Without that the initial ctx->init checks might
randomly return true and cause errors.
While there, also remove the redundant zero assignments in both
functions.
Found via libkcapi testsuite.
Cc: Stephan Mueller <smueller@chronox.de> Fixes: f3c802a1f300 ("crypto: algif_aead - Only wake up when ctx->more is zero") Suggested-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Recently xHCI driver switched to tasklets in the commit 36dc01657b49
("usb: host: xhci: Support running urb giveback in tasklet context").
The handle_irq_event_* functions are expected to be called with interrupts
disabled and they rightfully complain here because we run in tasklet context
with interrupts enabled.
Use a event spinlock to protect event handler from being interrupted.
Note, that there are only two users of this GPIO and ADC drivers and both of
them are using generic_handle_irq() which makes above happen.
Fixes: 338a12814297 ("mfd: Add support for Diolan DLN-2 devices") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When i2c client unregisters, synchronize irq before setting
iproc_i2c->slave to NULL.
(1) disable_irq()
(2) Mask event enable bits in control reg
(3) Erase slave address (avoid further writes to rx fifo)
(4) Flush tx and rx FIFOs
(5) Clear pending event (interrupt) bits in status reg
(6) enable_irq()
(7) Set client pointer to NULL
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000318
Reset the member "test_fs" of the test configuration after a call of the
function "kfree_const" to a null pointer so that a double memory release
will not be performed.
Fixes: d9c6a72d6fa2 ("kmod: add test driver to stress test the module loader") Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christian Brauner <christian.brauner@ubuntu.com> Cc: Chuck Lever <chuck.lever@oracle.com> Cc: David Howells <dhowells@redhat.com> Cc: David S. Miller <davem@davemloft.net> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jakub Kicinski <kuba@kernel.org> Cc: James Morris <jmorris@namei.org> Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Cc: J. Bruce Fields <bfields@fieldses.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Kees Cook <keescook@chromium.org> Cc: Lars Ellenberg <lars.ellenberg@linbit.com> Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: Philipp Reisner <philipp.reisner@linbit.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: "Serge E. Hallyn" <serge@hallyn.com> Cc: Sergei Trofimovich <slyfox@gentoo.org> Cc: Sergey Kvachonok <ravenexp@gmail.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Tony Vroon <chainsaw@gentoo.org> Cc: Christoph Hellwig <hch@infradead.org> Link: http://lkml.kernel.org/r/20200610154923.27510-4-mcgrof@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 64 bit ino is being compared to the product of two u32 values,
however, the multiplication is being performed using a 32 bit multiply so
there is a potential of an overflow. To be fully safe, cast uspi->s_ncg
to a u64 to ensure a 64 bit multiplication occurs to avoid any chance of
overflow.
Fixes: f3e2a520f5fb ("ufs: NFS support") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Evgeniy Dushistov <dushistov@mail.ru> Cc: Alexey Dobriyan <adobriyan@gmail.com> Link: http://lkml.kernel.org/r/20200715170355.1081713-1-colin.king@canonical.com
Addresses-Coverity: ("Unintentional integer overflow") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When truncating a file to a size within the last allowed logical block,
block_to_path() is called with the *next* block. This exceeds the limit,
causing the "block %ld too big" error message to be printed.
This case isn't actually an error; there are just no more blocks past that
point. So, remove this error message.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Qiujun Huang <anenbupt@gmail.com> Link: http://lkml.kernel.org/r/20200628060846.682158-7-ebiggers@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The minix filesystem reads its maximum file size from its on-disk
superblock. This value isn't necessarily a multiple of the block size.
When it's not, the V1 block mapping code doesn't allow mapping the last
possible block. Commit 6ed6a722f9ab ("minixfs: fix block limit check")
fixed this in the V2 mapping code. Fix it in the V1 mapping code too.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Qiujun Huang <anenbupt@gmail.com> Link: http://lkml.kernel.org/r/20200628060846.682158-6-ebiggers@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The minix filesystem leaves super_block::s_maxbytes at MAX_NON_LFS rather
than setting it to the actual filesystem-specific limit. This is broken
because it means userspace doesn't see the standard behavior like getting
EFBIG and SIGXFSZ when exceeding the maximum file size.
Fix this by setting s_maxbytes correctly.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Qiujun Huang <anenbupt@gmail.com> Link: http://lkml.kernel.org/r/20200628060846.682158-5-ebiggers@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since filp_open() returns an error pointer, we should use IS_ERR() to
check the return value and then return PTR_ERR() if failed to get the
actual return value instead of always -EINVAL.
E.g. without this patch:
[root@localhost loongson]# ls no_such_file
ls: cannot access no_such_file: No such file or directory
[root@localhost loongson]# modprobe test_lockup file_path=no_such_file lock_sb_umount time_secs=60 state=S
modprobe: ERROR: could not insert 'test_lockup': Invalid argument
[root@localhost loongson]# dmesg | tail -1
[ 126.100596] test_lockup: cannot find file_path
With this patch:
[root@localhost loongson]# ls no_such_file
ls: cannot access no_such_file: No such file or directory
[root@localhost loongson]# modprobe test_lockup file_path=no_such_file lock_sb_umount time_secs=60 state=S
modprobe: ERROR: could not insert 'test_lockup': Unknown symbol in module, or unknown parameter (see dmesg)
[root@localhost loongson]# dmesg | tail -1
[ 95.134362] test_lockup: failed to open no_such_file: -2
Fixes: aecd42df6d39 ("lib/test_lockup.c: add parameters for locking generic vfs locks") Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Kees Cook <keescook@chromium.org> Link: http://lkml.kernel.org/r/1595555407-29875-2-git-send-email-yangtiezhu@loongson.cn Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current mirrored read failover code is correctly resetting the mirror
index between failed reads, however it is not able to actually flip the
RPC call over to the next RPC client.
The end result is that we keep resending the RPC call to the same client
over and over.
The fix is to use the pnfs_read_resend_pnfs() mechanism to schedule a
new RPC call, but we need to add the ability to pass in a mirror
index so that we always retry the next mirror in the list.
Fix the missing clk_disable_unprepare() before return
from emac_clks_phase1_init() in the error handling case.
Fixes: b9b17debc69d ("net: emac: emac gigabit ethernet controller driver") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Acked-by: Timur Tabi <timur@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The VFIO_AP uses ap_driver_register() (and deregister) functions
implemented in ap_bus.c (compiled into ap.o). However the ap.o will be
built only if CONFIG_ZCRYPT is selected.
This was not visible before commit e93a1695d7fb ("iommu: Enable compile
testing for some of drivers") because the CONFIG_VFIO_AP depends on
CONFIG_S390_AP_IOMMU which depends on the missing CONFIG_ZCRYPT. After
adding COMPILE_TEST, it is possible to select a configuration with
VFIO_AP and S390_AP_IOMMU but without the ZCRYPT.
Add proper dependency to the VFIO_AP to fix build errors:
These if statements are supposed to be true if we ended the
list_for_each_entry() loops without hitting a break statement but they
don't work.
In the first loop, we increment "i" after the "if (i == unit)" condition
so we don't necessarily know that "i" is not equal to unit at the end of
the loop.
In the second loop we exit when mode is not pointing to a valid
drm_display_mode struct so it doesn't make sense to check "mode->type".
Fixes: a278724aa23c ("drm/vmwgfx: Implement fbdev on kms v2") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Roland Scheidegger <sroland@vmware.com> Signed-off-by: Roland Scheidegger <sroland@vmware.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "entry" pointer is an offset from the list head and it doesn't
point to a valid vmw_legacy_display_unit struct. Presumably the
intent was to point to the last entry.
Also the "i++" wasn't used so I have removed that as well.
Fixes: d7e1958dbe4a ("drm/vmwgfx: Support older hardware.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Roland Scheidegger <sroland@vmware.com> Signed-off-by: Roland Scheidegger <sroland@vmware.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If "offset" is non-zero then we end up copying from beyond the end of
the config because of pointer math. We can fix this by casting the
struct to a u8 pointer.
Fixes: 2c53d0f64c06 ("vdpasim: vDPA device simulator") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20200406144552.GF68494@mwanda Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit ea0eada45632 leads to the following build failure on powerpc:
HOSTCC scripts/recordmcount
scripts/recordmcount.c: In function 'arm64_is_fake_mcount':
scripts/recordmcount.c:440: error: 'R_AARCH64_CALL26' undeclared (first use in this function)
scripts/recordmcount.c:440: error: (Each undeclared identifier is reported only once
scripts/recordmcount.c:440: error: for each function it appears in.)
make[2]: *** [scripts/recordmcount] Error 1
Make sure R_AARCH64_CALL26 is always defined.
Fixes: ea0eada45632 ("recordmcount: only record relocation of type R_AARCH64_CALL26 on arm64.") Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by: Gregory Herrero <gregory.herrero@oracle.com> Cc: Gregory Herrero <gregory.herrero@oracle.com> Link: https://lore.kernel.org/r/5ca1be21fa6ebf73203b45fd9aadd2bafb5e6b15.1597049145.git.christophe.leroy@csgroup.eu Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently when the call to fsp_reg_write fails -EIO is not being returned
because the count is being returned instead of the return value in retval.
Fix this by returning the value in retval instead of count.
Addresses-Coverity: ("Unused value") Fixes: fc69f4a6af49 ("Input: add new driver for Sentelic Finger Sensing Pad") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20200603141218.131663-1-colin.king@canonical.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
runqslower's Makefile is building/installing bpftool into
$(OUTPUT)/sbin/bpftool, which coincides with $(DEFAULT_BPFTOOL). In practice
this means that often when building selftests from scratch (after `make
clean`), selftests are racing with runqslower to simultaneously build bpftool
and one of the two processes fail due to file being busy. Prevent this race by
explicitly order-depending on $(BPFTOOL_DEFAULT).
Fixes: a2c9652f751e ("selftests: Refactor build to remove tools/lib/bpf from include path") Signed-off-by: Andrii Nakryiko <andriin@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20200805004757.2960750-1-andriin@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org>
System is not vulnerable to DoS attack from a rogue guest when
virtualization is disabled or unsupported in the hardware. Change the
mitigation reporting for these cases.
Fixes: b8e8c8303ff2 ("kvm: mmu: ITLB_MULTIHIT mitigation") Reported-by: Nelson Dsouza <nelson.dsouza@linux.intel.com> Co-developed-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Tony Luck <tony.luck@intel.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/0ba029932a816179b9d14a30db38f0f11ef1f166.1594925782.git.pawan.kumar.gupta@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Frequency descriptor of Lightning Mountain SoC doesn't have all the
frequency entries so resulting in the below failure causing a kernel hang:
Error MSR_FSB_FREQ index 15 is unknown
tsc: Fast TSC calibration failed
So, add all the frequency entries in the Lightning Mountain SoC frequency
descriptor.
Fixes: 0cc5359d8fd45 ("x86/cpu: Update init data for new Airmont CPU model") Fixes: 812c2d7506fd ("x86/tsc_msr: Use named struct initializers") Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/211c643ae217604b46cbec43a2c0423946dc7d2d.1596440057.git.eswara.kota@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The error handling calls md_bitmap_free(bitmap) which checks for NULL
but will Oops if we pass an error pointer. Let's set "bitmap" to NULL
on this error path.
Fixes: afd756286083 ("md-cluster/raid10: resize all the bitmaps before start reshape") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When watchdog device is being registered, it calls misc_register that
makes watchdog available for systemd to open. This is a data race
scenario, because when device is open it may still have device struct
not initialized - this in turn causes a crash. This patch moves
device initialization before misc_register call and it solves the
problem printed below.
------------[ cut here ]------------
WARNING: CPU: 3 PID: 1 at lib/kobject.c:612 kobject_get+0x50/0x54
kobject: '(null)' ((ptrval)): is not initialized, yet kobject_get() is being called.
Modules linked in: k2_reset_status(O) davinci_wdt(+) sfn_platform_hwbcn(O) fsmddg_sfn(O) clk_misc_mmap(O) clk_sw_bcn(O) fsp_reset(O) cma_mod(O) slave_sup_notif(O) fpga_master(O) latency(O+) evnotify(O) enable_arm_pmu(O) xge(O) rio_mport_cdev br_netfilter bridge stp llc nvrd_checksum(O) ipv6
CPU: 3 PID: 1 Comm: systemd Tainted: G O 4.19.113-g2579778-fsm4_k2 #1
Hardware name: Keystone
[<c02126c4>] (unwind_backtrace) from [<c020da94>] (show_stack+0x18/0x1c)
[<c020da94>] (show_stack) from [<c07f87d8>] (dump_stack+0xb4/0xe8)
[<c07f87d8>] (dump_stack) from [<c0221f70>] (__warn+0xfc/0x114)
[<c0221f70>] (__warn) from [<c0221fd8>] (warn_slowpath_fmt+0x50/0x74)
[<c0221fd8>] (warn_slowpath_fmt) from [<c07fd394>] (kobject_get+0x50/0x54)
[<c07fd394>] (kobject_get) from [<c0602ce8>] (get_device+0x1c/0x24)
[<c0602ce8>] (get_device) from [<c06961e0>] (watchdog_open+0x90/0xf0)
[<c06961e0>] (watchdog_open) from [<c06001dc>] (misc_open+0x130/0x17c)
[<c06001dc>] (misc_open) from [<c0388228>] (chrdev_open+0xec/0x1a8)
[<c0388228>] (chrdev_open) from [<c037fa98>] (do_dentry_open+0x204/0x3cc)
[<c037fa98>] (do_dentry_open) from [<c0391e2c>] (path_openat+0x330/0x1148)
[<c0391e2c>] (path_openat) from [<c0394518>] (do_filp_open+0x78/0xec)
[<c0394518>] (do_filp_open) from [<c0381100>] (do_sys_open+0x130/0x1f4)
[<c0381100>] (do_sys_open) from [<c0201000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xd2ceffa8 to 0xd2cefff0)
ffa0: b6f6996800000000ffffff9cb6ebd210000a000100000000
ffc0: b6f69968000000000000000000000142fffffffdffffffff00b65530bed7bb78
ffe0: 00000142bed7ba70b6cc2503b6cc41d6
---[ end trace 7b16eb105513974f ]---
------------[ cut here ]------------
WARNING: CPU: 3 PID: 1 at lib/refcount.c:153 kobject_get+0x24/0x54
refcount_t: increment on 0; use-after-free.
Modules linked in: k2_reset_status(O) davinci_wdt(+) sfn_platform_hwbcn(O) fsmddg_sfn(O) clk_misc_mmap(O) clk_sw_bcn(O) fsp_reset(O) cma_mod(O) slave_sup_notif(O) fpga_master(O) latency(O+) evnotify(O) enable_arm_pmu(O) xge(O) rio_mport_cdev br_netfilter bridge stp llc nvrd_checksum(O) ipv6
CPU: 3 PID: 1 Comm: systemd Tainted: G W O 4.19.113-g2579778-fsm4_k2 #1
Hardware name: Keystone
[<c02126c4>] (unwind_backtrace) from [<c020da94>] (show_stack+0x18/0x1c)
[<c020da94>] (show_stack) from [<c07f87d8>] (dump_stack+0xb4/0xe8)
[<c07f87d8>] (dump_stack) from [<c0221f70>] (__warn+0xfc/0x114)
[<c0221f70>] (__warn) from [<c0221fd8>] (warn_slowpath_fmt+0x50/0x74)
[<c0221fd8>] (warn_slowpath_fmt) from [<c07fd368>] (kobject_get+0x24/0x54)
[<c07fd368>] (kobject_get) from [<c0602ce8>] (get_device+0x1c/0x24)
[<c0602ce8>] (get_device) from [<c06961e0>] (watchdog_open+0x90/0xf0)
[<c06961e0>] (watchdog_open) from [<c06001dc>] (misc_open+0x130/0x17c)
[<c06001dc>] (misc_open) from [<c0388228>] (chrdev_open+0xec/0x1a8)
[<c0388228>] (chrdev_open) from [<c037fa98>] (do_dentry_open+0x204/0x3cc)
[<c037fa98>] (do_dentry_open) from [<c0391e2c>] (path_openat+0x330/0x1148)
[<c0391e2c>] (path_openat) from [<c0394518>] (do_filp_open+0x78/0xec)
[<c0394518>] (do_filp_open) from [<c0381100>] (do_sys_open+0x130/0x1f4)
[<c0381100>] (do_sys_open) from [<c0201000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xd2ceffa8 to 0xd2cefff0)
ffa0: b6f6996800000000ffffff9cb6ebd210000a000100000000
ffc0: b6f69968000000000000000000000142fffffffdffffffff00b65530bed7bb78
ffe0: 00000142bed7ba70b6cc2503b6cc41d6
---[ end trace 7b16eb1055139750 ]---
Fixes: 72139dfa2464 ("watchdog: Fix the race between the release of watchdog_core_data and cdev") Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Krzysztof Sobota <krzysztof.sobota@nokia.com> Link: https://lore.kernel.org/r/20200717103109.14660-1-krzysztof.sobota@nokia.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The NFS_CONTEXT_ERROR_WRITE flag (as well as the check of said flag) was
removed by commit 6fbda89b257f. The absence of an error check allows
writes to be continually queued up for a server that may no longer be
able to handle them. Fix it by adding an error check using the generic
error reporting functions.
We cannot wait on a completion object in the lpfc_nvme_targetport structure
in the _destroy_targetport() code path because the NVMe/fc transport will
free that structure immediately after the .targetport_delete() callback.
This results in a use-after-free, and a crash if slub_debug=FZPU is
enabled.
An earlier fix put put the completion on the stack, but commit 2a0fb340fcc8
("scsi: lpfc: Correct localport timeout duration error") subsequently
changed the code to reference the completion through a pointer in the
object rather than the local stack variable. Fix this by using the stack
variable directly.
Link: https://lore.kernel.org/r/20200729231011.13240-1-emilne@redhat.com Fixes: 2a0fb340fcc8 ("scsi: lpfc: Correct localport timeout duration error") Reviewed-by: James Smart <james.smart@broadcom.com> Signed-off-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This was caused by the stack trace code in save_stack_trace_tsk using
the wrong stack pointer. It was using the user stack pointer instead of
the kernel stack pointer. Fix this by using the right stack.
Also for good measure we add try_get_task_stack/put_task_stack to ensure
the task is not lost while we are walking it's stack.
Fixes: eecac38b0423a ("openrisc: support framepointers and STACKTRACE_SUPPORT") Signed-off-by: Stafford Horne <shorne@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7d988097c546 ("acpi/nfit, libnvdimm/security: Add security DSM overwrite support")
adds a sysfs_notify_dirent() to wake up userspace poll thread when the "overwrite"
operation has completed. But the notification is issued before the internal
dimm security state and flags have been updated, so the userspace poll thread
wakes up and fetches the not-yet-updated attr and falls back to sleep, forever.
But if user from another terminal issue "ndctl wait-overwrite nmemX" again,
the command returns instantly.
Link: https://lore.kernel.org/r/1596494499-9852-3-git-send-email-jane.chu@oracle.com Fixes: 7d988097c546 ("acpi/nfit, libnvdimm/security: Add security DSM overwrite support") Cc: Dave Jiang <dave.jiang@intel.com> Cc: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jane Chu <jane.chu@oracle.com> Signed-off-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d78c620a2e82 ("libnvdimm/security: Introduce a 'frozen' attribute")
introduced a typo, causing a 'nvdimm->sec.flags' update being overwritten
by the subsequent update meant for 'nvdimm->sec.ext_flags'.
Link: https://lore.kernel.org/r/1596494499-9852-1-git-send-email-jane.chu@oracle.com Fixes: d78c620a2e82 ("libnvdimm/security: Introduce a 'frozen' attribute") Cc: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Jane Chu <jane.chu@oracle.com> Signed-off-by: Vishal Verma <vishal.l.verma@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Contrary to previous SoCs, bcm2711 doesn't have a prescaler in the PLL
feedback loop. Bypass it by zeroing fb_prediv_mask when running on
bcm2711.
Note that, since the prediv configuration bits were re-purposed, this
was triggering miscalculations on all clocks hanging from the VPU clock,
notably the aux UART, making its output unintelligible.
nfs_wb_all() calls filemap_write_and_wait(), which uses
filemap_check_errors() to determine the error to return.
filemap_check_errors() only looks at the mapping->flags and will
therefore only return either -ENOSPC or -EIO. To ensure that the
correct error is returned on close(), nfs{,4}_file_flush() should call
filemap_check_wb_err() which looks at the errseq value in
mapping->wb_err without consuming it.
Due to the lockless design of the driver, it is theoretically possible
to access a NULL pointer, if a slave interrupt was running while we were
unregistering the slave. To make this rock solid, disable the interrupt
for a short time while we are clearing the interrupt_enable register.
This patch is purely based on code inspection. The OOPS is super-hard to
trigger because clearing SAR (the address) makes interrupts even more
unlikely to happen as well. While here, reinit SCR to SDBS because this
bit should always be set according to documentation. There is no effect,
though, because the interface is disabled.
Fixes: 7b814d852af6 ("i2c: rcar: avoid race when unregistering slave client") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c8c188679ccf ("tools build: Use the same CC for feature detection
and actual build") changed these assignments from unconditional (:=) to
conditional (?=) so that they wouldn't clobber values from the
environment. However, conditional assignment does not work properly for
variables that Make implicitly sets, among which are CC and CXX. To
quote tools/scripts/Makefile.include, which handles this properly:
# Makefiles suck: This macro sets a default value of $(2) for the
# variable named by $(1), unless the variable has been set by
# environment or command line. This is necessary for CC and AR
# because make sets default values, so the simpler ?= approach
# won't work as expected.
In other words, the conditional assignments will not run even if the
variables are not overridden in the environment; Make will set CC to
"cc" and CXX to "g++" when it starts[1], meaning the variables are not
empty by the time the conditional assignments are evaluated. This breaks
cross-compilation when CROSS_COMPILE is set but CC isn't, since "cc"
gets used for feature detection instead of the cross compiler (and
likewise for CXX).
To fix the issue, just pass down the values of CC and CXX computed by
the parent Makefile, which gets included by the Makefile that actually
builds whatever we're detecting features for and so is guaranteed to
have good values. This is a better solution anyway, since it means we
aren't trying to replicate the logic of the parent build system and so
don't risk it getting out of sync.
Leave PKG_CONFIG alone, since 1) there's no common logic to compute it
in Makefile.include, and 2) it's not an implicit variable, so
conditional assignment works properly.
Fixes: c8c188679ccf ("tools build: Use the same CC for feature detection and actual build") Signed-off-by: Thomas Hebb <tommyhebb@gmail.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: David Carrillo-Cisneros <davidcc@google.com> Cc: Ian Rogers <irogers@google.com> Cc: Igor Lubashev <ilubashe@akamai.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Quentin Monnet <quentin@isovalent.com> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Cc: thomas hebb <tommyhebb@gmail.com> Link: http://lore.kernel.org/lkml/0a6e69d1736b0fa231a648f50b0cce5d8a6734ef.1595822871.git.tommyhebb@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A deadlock happens in the following scenario with multipath:
1) scan_work(nvme0) detects a new nsid while nvme0
is an optimized path to it, path nvme1 happens to be
inaccessible.
2) Before scan_work is complete nvme0 disconnect is initiated
nvme_delete_ctrl_sync() sets nvme0 state to NVME_CTRL_DELETING
3) scan_work(1) attempts to submit IO,
but nvme_path_is_optimized() observes nvme0 is not LIVE.
Since nvme1 is a possible path IO is requeued and scan_work hangs.
4) Delete also hangs in flush_work(ctrl->scan_work)
from nvme_remove_namespaces().
Similiarly a deadlock with ana_work may happen: if ana_work has started
and calls nvme_mpath_set_live and device_add_disk, it will
trigger I/O. When we trigger disconnect I/O will block because
our accessible (optimized) path is disconnecting, but the alternate
path is inaccessible, so I/O blocks. Then disconnect tries to flush
the ana_work and hangs.
Fix this by introducing a new state: NVME_CTRL_DELETE_NOIO, which will
indicate the phase of controller deletion where I/O cannot be allowed
to access the namespace. NVME_CTRL_DELETING still allows mpath I/O to
be issued to the bottom device, and only after we flush the ana_work
and scan_work (after nvme_stop_ctrl and nvme_prep_remove_namespaces)
we change the state to NVME_CTRL_DELETING_NOIO. Also we prevent ana_work
from re-firing by aborting early if we are not LIVE, so we should be safe
here.
In addition, change the transport drivers to follow the updated state
machine.
Fixes: 0d0b660f214d ("nvme: add ANA support") Reported-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function clk_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Xu Wang <vulab@iscas.ac.cn> Link: https://lore.kernel.org/r/20200713032143.21362-1-vulab@iscas.ac.cn Acked-by: Barry Song <baohua@kernel.org> Fixes: 7bf21bc81f28 ("clk: sirf: re-arch to make the codes support both prima2 and atlas6") Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the SSR interrupt is activated, it will detect every STOP condition
on the bus, not only the ones after we have been addressed. So, enable
this interrupt only after we have been addressed, and disable it
otherwise.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support") Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set proper masks to avoid invalid input spillover to reserved bits.
Signed-off-by: Liu Yi L <yi.l.liu@intel.com> Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Link: https://lore.kernel.org/r/20200724014925.15523-2-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the parents and set BRANCH_HALT_SKIP. From the downstream driver it
should be a 500us delay and not skip, however this matches what was done
for other clocks that had 500us delay in downstream.
Fixes: f73a4230d5bb ("clk: qcom: gcc: Add GPU and NPU clocks for SM8150") Signed-off-by: Jonathan Marek <jonathan@marek.ca> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Link: https://lore.kernel.org/r/20200709135251.643-2-jonathan@marek.ca Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible for the call to omap_iommu_dump_ctx to return
a negative error number, so check for the failure and return
the error number rather than pass the negative value to
simple_read_from_buffer.
Fixes: 14e0e6796a0d ("OMAP: iommu: add initial debugfs support") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20200714192211.744776-1-colin.king@canonical.com
Addresses-Coverity: ("Improper use of negative value") Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
With commit 4a4a5e5d2aad ("powerpc/pkeys: key allocation/deallocation
must not change pkey registers") we are not updating UAMOR on key
allocation. So don't update the expected uamor value in the test.
Fixes: 4a4a5e5d2aad ("powerpc/pkeys: key allocation/deallocation must not change pkey registers") Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200709032946.881753-23-aneesh.kumar@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory allocated for storing compressed pages' poitner should be
released after f2fs_write_compressed_pages(), otherwise it will
cause memory leak issue.
Signed-off-by: Chao Yu <yuchao0@huawei.com> Fixes: 4c8ff7095bef ("f2fs: support data compression") Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Verifying that a file hash is not blacklisted is currently only
supported for files with appended signatures (modsig). In the future,
this might change.
For now, the "appraise_flag" option is only appropriate for appraise
actions and its "blacklist" value is only appropriate when
CONFIG_IMA_APPRAISE_MODSIG is enabled and "appraise_flag=blacklist" is
only appropriate when "appraise_type=imasig|modsig" is also present.
Make this clear at policy load so that IMA policy authors don't assume
that other uses of "appraise_flag=blacklist" are supported.
dm_stop_queue() only uses blk_mq_quiesce_queue() so it doesn't
formally stop the blk-mq queue; therefore there is no point making the
blk_mq_queue_stopped() check -- it will never be stopped.
In addition, even though dm_stop_queue() actually tries to quiesce hw
queues via blk_mq_quiesce_queue(), checking with blk_queue_quiesced()
to avoid unnecessary queue quiesce isn't reliable because: the
QUEUE_FLAG_QUIESCED flag is set before synchronize_rcu() and
dm_stop_queue() may be called when synchronize_rcu() from another
blk_mq_quiesce_queue() is in-progress.
Fixes: 7b17c2f7292ba ("dm: Fix a race condition related to stopping and starting queues") Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use a bit-mask of EOF irqs to determine when all required idmac
channel EOFs have been received for a tile conversion, and only do
tile completion processing after all EOFs have been received. Otherwise
it was found that a conversion would stall after the completion of a
tile and the start of the next tile, because the input/read idmac
channel had not completed and entered idle state, thus locking up the
channel when attempting to re-start it for the next tile.
Fixes: 0537db801bb01 ("gpu: ipu-v3: image-convert: reconfigure IC per tile") Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The arc4 algorithm requires storing state in the request context
in order to allow more than one encrypt/decrypt operation. As this
driver does not seem to do that, it means that using it for more
than one operation is broken.
Commit c8ff5841a90b ("rtc: pl031: switch to rtc_time64_to_tm/rtc_tm_to_time64")
seemed to have accidentally removed the call to pl031_alarm_irq_enable
from pl031_set_alarm while switching to 64-bit apis.
Let us add back the same to get the set alarm functionality back.
Some platforms cannot read the DBI register successfully for the
ASPM settings. After the read failed, the bus could be unstable,
and the device just became unavailable [1]. For those platforms,
the ASPM should be disabled. But as the ASPM can help the driver
to save the power consumption in power save mode, the ASPM is still
needed. So, add a module parameter for them to disable it, then
the device can still work, while others can benefit from the less
power consumption that brings by ASPM enabled.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=206411
[2] Note that my lenovo T430 is the same.
Fixes: 3dff7c6e3749 ("rtw88: allows to enable/disable HCI link PS mechanism") Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200605074703.32726-1-yhchuang@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In manual mode allow bind user QPs with different pids to same counter,
since this is allowed in auto mode.
Bind kernel QPs and user QPs to the same counter are not allowed.
Fixes: 1bd8e0a9d0fd ("RDMA/counter: Allow manual mode configuration support") Link: https://lore.kernel.org/r/20200702082933.424537-4-leon@kernel.org Signed-off-by: Mark Zhang <markz@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In auto mode only bind user QPs to a dynamic counter, since this feature
is mainly used for system statistic and diagnostic purpose, while there's
no need to counter kernel QPs so far.
Fixes: 99fa331dc862 ("RDMA/counter: Add "auto" configuration mode support") Link: https://lore.kernel.org/r/20200702082933.424537-3-leon@kernel.org Signed-off-by: Mark Zhang <markz@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sometimes debugging a device is easiest using devmem on its register
map, and that can be seen with /proc/iomem. But some device drivers have
many memory regions. Take for example a networking switch. Its memory
map used to look like this in /proc/iomem:
That patch made a fair comment that /proc/iomem might be confusing when
it shows resources without an associated device, but we can do better
than just hide the resource name altogether. Namely, we can print the
device name _and_ the resource name. Like this:
Some user-space programs rely on crypto requests that have no
control metadata. This broke when a check was added to require
the presence of control metadata with the ctx->init flag.
This patch fixes the regression by setting ctx->init as long as
one sendmsg(2) has been made, with or without a control message.
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com> Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Fixes: f3c802a1f300 ("crypto: algif_aead - Only wake up when...") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are a number of places in test_progs that use minus-1 as the argument
to exit(). This is confusing as a process exit status is masked to be a
number between 0 and 255 as defined in man exit(3). Thus, users will see
status 255 instead of minus-1.
This patch use positive exit code 3 instead of minus-1. These cases are put
in the same group of infrastructure setup errors.
Fixes: fd27b1835e70 ("selftests/bpf: Reset process and thread affinity after each test/sub-test") Fixes: 811d7e375d08 ("bpf: selftests: Restore netns after each test") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/159410594499.1093222.11080787853132708654.stgit@firesoul Signed-off-by: Sasha Levin <sashal@kernel.org>
This is a follow up adjustment to commit 6c92bd5cd465 ("selftests/bpf:
Test_progs indicate to shell on non-actions"), that returns shell exit
indication EXIT_FAILURE (value 1) when user selects a non-existing test.
The problem with using EXIT_FAILURE is that a shell script cannot tell
the difference between a non-existing test and the test failing.
This patch uses value 2 as shell exit indication.
(Aside note unrecognized option parameters use value 64).
Fixes: 6c92bd5cd465 ("selftests/bpf: Test_progs indicate to shell on non-actions") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/159410593992.1093222.90072558386094370.stgit@firesoul Signed-off-by: Sasha Levin <sashal@kernel.org>
It is common for networking tests creating its netns and making its own
setting under this new netns (e.g. changing tcp sysctl). If the test
forgot to restore to the original netns, it would affect the
result of other tests.
This patch saves the original netns at the beginning and then restores it
after every test. Since the restore "setns()" is not expensive, it does it
on all tests without tracking if a test has created a new netns or not.
The new restore_netns() could also be done in test__end_subtest() such
that each subtest will get an automatic netns reset. However,
the individual test would lose flexibility to have total control
on netns for its own subtests. In some cases, forcing a test to do
unnecessary netns re-configure for each subtest is time consuming.
e.g. In my vm, forcing netns re-configure on each subtest in sk_assign.c
increased the runtime from 1s to 8s. On top of that, test_progs.c
is also doing per-test (instead of per-subtest) cleanup for cgroup.
Thus, this patch also does per-test restore_netns(). The only existing
per-subtest cleanup is reset_affinity() and no test is depending on this.
Thus, it is removed from test__end_subtest() to give a consistent
expectation to the individual tests. test_progs.c only ensures
any affinity/netns/cgroup change made by an earlier test does not
affect the following tests.
Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/20200702004858.2103728-1-kafai@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When a user selects a non-existing test the summary is printed with
indication 0 for all info types, and shell "success" (EXIT_SUCCESS) is
indicated. This can be understood by a human end-user, but for shell
scripting is it useful to indicate a shell failure (EXIT_FAILURE).
While investigating the root cause, there were no sign that the uclamp
code is doing anything particularly expensive but could suffer from bad
cache behavior under certain circumstances that are yet to be
understood.
To reduce the pressure on the fast path anyway, add a static key that is
by default will skip executing uclamp logic in the
enqueue/dequeue_task() fast path until it's needed.
As soon as the user start using util clamp by:
1. Changing uclamp value of a task with sched_setattr()
2. Modifying the default sysctl_sched_util_clamp_{min, max}
3. Modifying the default cpu.uclamp.{min, max} value in cgroup
We flip the static key now that the user has opted to use util clamp.
Effectively re-introducing uclamp logic in the enqueue/dequeue_task()
fast path. It stays on from that point forward until the next reboot.
This should help minimize the effect of util clamp on workloads that
don't need it but still allow distros to ship their kernels with uclamp
compiled in by default.
SCHED_WARN_ON() in uclamp_rq_dec_id() was removed since now we can end
up with unbalanced call to uclamp_rq_dec_id() if we flip the key while
a task is running in the rq. Since we know it is harmless we just
quietly return if we attempt a uclamp_rq_dec_id() when
rq->uclamp[].bucket[].tasks is 0.
In schedutil, we introduce a new uclamp_is_enabled() helper which takes
the static key into account to ensure RT boosting behavior is retained.
The following results demonstrates how this helps on 2 Sockets Xeon E5
2x10-Cores system.
Set IOVA on IB MR in uverbs layer to let all drivers have it, this
includes both reg/rereg MR flows.
As part of this change cleaned-up this setting from the drivers that
already did it by themselves in their user flows.
Fixes: e6f0330106f4 ("mlx4_ib: set user mr attributes in struct ib_mr") Link: https://lore.kernel.org/r/20200630093916.332097-3-leon@kernel.org Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting the output CSC mode is required for a YUV output, but must not
be set when the input is also YUV. Doing this (as tested with a YUV420P
to YUV420P conversion) results in wrong colors.
Adapt the logic to only set the output CSC mode when the output is YUV and
the input is RGB. Also add a comment to clarify the rationale.
This introduces two macros: RGA_COLOR_FMT_IS_YUV and RGA_COLOR_FMT_IS_RGB
which allow quick checking of the colorspace familily of a RGA color format.
These macros are then used to refactor the logic for CSC mode selection.
The two nested tests for input colorspace are simplified into a single one,
with a logical and, making the whole more readable.
The macro RKISP1_DIR_SINK_SRC is a mask of two flags.
The macro hides the fact that it's a mask and the code
is actually more clear if we replace it the with bitwise-or explicitly.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com> Acked-by: Helen Koike <helen.koike@collabora.com> Reviewed-by: Tomasz Figa <tfiga@chromium.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unbreak CPCAP driver, which has one more bit in the day counter
increasing the max. range from 2014 to 2058. The original commit
introducing the range limit was obviously wrong, since the driver
has only been written in 2017 (3 years after 14 bits would have
run out).
Fixes: d2377f8cc5a7 ("rtc: cpcap: set range") Reported-by: Sicelo A. Mhlongo <absicsz@gmail.com> Reported-by: Dev Null <devnull@uvos.xyz> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Tested-by: Merlijn Wajer <merlijn@wizzup.org> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Merlijn Wajer <merlijn@wizzup.org> Link: https://lore.kernel.org/r/20200629114123.27956-1-sebastian.reichel@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
ipoib_mcast_carrier_on_task() insanely open codes a rtnl_lock() such that
the only time flush_workqueue() can be called is if it also clears
IPOIB_FLAG_OPER_UP.
Thus the flush inside ipoib_flush_ah() will deadlock if it gets unlucky
enough, and lockdep doesn't help us to find it early:
ipoib_mcast_carrier_on_task()
while (!rtnl_trylock())
msleep(20);
ipoib_flush_ah()
flush_workqueue(priv->wq)
Clean up the ah_reaper related functions and lifecycle to make sense:
- Start/Stop of the reaper should only be done in open/stop NDOs, not in
any other places
- cancel and flush of the reaper should only happen in the stop NDO.
cancel is only functional when combined with IPOIB_STOP_REAPER.
- Non-stop places were flushing the AH's just need to flush out dead AH's
synchronously and ignore the background task completely. It is fully
locked and harmless to leave running.
Which ultimately fixes the ABBA deadlock by removing the unnecessary
flush_workqueue() from the problematic place under the vlan_rwsem.
Fixes: efc82eeeae4e ("IB/ipoib: No longer use flush as a parameter") Link: https://lore.kernel.org/r/20200625174219.290842-1-kamalheib1@gmail.com Reported-by: Kamal Heib <kheib@redhat.com> Tested-by: Kamal Heib <kheib@redhat.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In function cros_ec_ishtp_probe(), "up_write" is already called
before function "cros_ec_dev_init". But "up_write" will be called
again after the calling of the function "cros_ec_dev_init" failed.
Thus add a call of the function “down_write” in this if branch
for the completion of the exception handling.
projects / linux-stable / log