Commit eeca7d46217c ("arm64: dts: qcom: pm8350c: Drop PWM reg declaration")
dropped PWM reg declaration for pm8350c pwm(s), but there is a leftover
'reg' entry inside the lpg/pwm node in sc8280xp dts file. Remove the same.
While at it, also remove the unused unit address in the node
label.
Also, since dt-bindings expect LPG/PWM node name to be "pwm",
use correct node name as well, to fix the following
error reported by 'make dtbs_check':
There is an outstanding binutils issue to support a non-constant operand
to .sleb128 and .uleb128 in GAS for RISC-V but there does not appear to
be any movement on it, due to concerns over how it would work with
linker relaxation.
To avoid these build errors, prevent DWARF5 from being selected when
using clang and an assembler that does not have support for these symbol
deltas, which can be easily checked in Kconfig with as-instr plus the
small test program from the dwz test suite from the binutils issue.
CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT does not give explicit
-gdwarf-* flag. The actual DWARF version is up to the toolchain.
The combination of GCC and GAS works fine, and Clang with the integrated
assembler is good too.
The combination of Clang and GAS is tricky, but at least, the -g flag
works for Clang <=13, which defaults to DWARF v4.
Clang 14 switched its default to DWARF v5.
Now, CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT has the same issue as
addressed by commit 98cd6f521f10 ("Kconfig: allow explicit opt in to
DWARF v5").
CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y for Clang >= 14 and
GAS < 2.35 produces a ton of errors like follows:
/tmp/main-c2741c.s: Assembler messages:
/tmp/main-c2741c.s:109: Error: junk at end of line, first unrecognized character is `"'
/tmp/main-c2741c.s:109: Error: file number less than one
A previous commit moved the notifications and end-write handling, but
it is now missing a few spots where we also want to call both of those.
Without that, we can potentially be missing file notifications, and
more importantly, have an imbalance in the super_block writers sem
accounting.
After commit 8799c0be89eb ("drm/amd/display: Fix vblank refcount in vrr
transition"), a build with CONFIG_DEBUG_FS=n is broken due to a
misplaced brace, along the lines of:
In file included from drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_trace.h:39,
from drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:41:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c: At top level:
./include/drm/drm_atomic.h:864:9: error: expected identifier or ‘(’ before ‘for’
864 | for ((__i) = 0; \
| ^~~
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:8317:9: note: in expansion of macro ‘for_each_new_crtc_in_state’
8317 | for_each_new_crtc_in_state(state, crtc, new_crtc_state, j)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Move the brace within the #ifdef so that the file can be built with or
without CONFIG_DEBUG_FS.
It's possible for an interrupt returning to an irqs-disabled context to
lose a pending soft-masked irq because it branches to part of the exit
code for irqs-enabled contexts, which is meant to clear only the
PACA_IRQS_HARD_DIS flag from PACAIRQHAPPENED by zeroing the byte. This
just looks like a simple thinko from a recent commit (if there was no
hard mask pending, there would be no reason to clear it anyway).
This also adds comment to the code that actually does need to clear the
flag.
Fixes: e485f6c751e0a ("powerpc/64/interrupt: Fix return to masked context after hard-mask irq becomes pending") Reported-by: Sachin Sant <sachinp@linux.ibm.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20221013064418.1311104-1-npiggin@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is hitting skb_assert_len() warning at __dev_queue_xmit() [1],
for PF_IEEE802154 socket's zero-sized raw_sendmsg() request is hitting
__dev_queue_xmit() with skb->len == 0.
Since PF_IEEE802154 socket's zero-sized raw_sendmsg() request was
able to return 0, don't call __dev_queue_xmit() if packet length is 0.
Note that this might be a sign that commit fd1894224407c484 ("bpf: Don't
redirect packets with invalid pkt_len") should be reverted, for
skb->len == 0 was acceptable for at least PF_IEEE802154 socket.
davinci_mdio.c uses mdio bitbang APIs, so it should select
MDIO_BITBANG to prevent build errors.
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_remove':
drivers/net/ethernet/ti/davinci_mdio.c:649: undefined reference to `free_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_probe':
drivers/net/ethernet/ti/davinci_mdio.c:545: undefined reference to `alloc_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_read':
drivers/net/ethernet/ti/davinci_mdio.c:236: undefined reference to `mdiobb_read'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_write':
drivers/net/ethernet/ti/davinci_mdio.c:253: undefined reference to `mdiobb_write'
Fixes: d04807b80691 ("net: ethernet: ti: davinci_mdio: Add workaround for errata i2329") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Ravi Gunasekaran <r-gunasekaran@ti.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Naresh Kamboju <naresh.kamboju@linaro.org> Cc: Sudip Mukherjee (Codethink) <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20220824024216.4939-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c5035dfbb94 ("blk-wbt: call rq_qos_add() after wb_normal is
initialized") moves wbt_set_write_cache() before rq_qos_add(), which
is wrong because wbt_rq_qos() is still NULL.
Fix the problem by removing wbt_set_write_cache() and setting 'rwb->wc'
directly. Noted that this patch also remove the redundant setting of
'rab->wc'.
The recent fix in commit 6392dcd1d0c7 ("ALSA: usb-audio: Register card
at the last interface") tried to delay the card registration until the
last found interface is probed. It assumed that the probe callback
gets called for those later interfaces, but it's not always true; as
the driver loops over the descriptor and probes the matching ones,
it's not separately called via multiple probe calls. This results in
the missing card registration, i.e. no sound device.
For addressing this problem, replace the check whether the last
interface is processed with usb_interface_claimed() instead of the
comparison with the probe interface number.
Fixes: 6392dcd1d0c7 ("ALSA: usb-audio: Register card at the last interface") Link: https://lore.kernel.org/r/20220915085947.7922-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds handling to return -EINVAL for an unknown addr type. The
current behaviour is to return 0 as successful but the size of an
unknown addr type is not defined and should return an error like -EINVAL.
Fixes: 94160108a70c ("net/ieee802154: fix uninit value bug in dgram_sendmsg") Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vma_lock and hugetlb_fault_mutex are dropped before handling userfault
and reacquire them again after handle_userfault(), but reacquire the
vma_lock could lead to UAF[1,2] due to the following race,
Since the vma_lock will unlock immediately after
hugetlb_handle_userfault(), let's drop the unneeded lock and unlock in
hugetlb_handle_userfault() to fix the issue.
[1] https://lore.kernel.org/linux-mm/000000000000d5e00a05e834962e@google.com/
[2] https://lore.kernel.org/linux-mm/20220921014457.1668-1-liuzixian4@huawei.com/ Link: https://lkml.kernel.org/r/20220923042113.137273-1-liushixin2@huawei.com Fixes: 1a1aad8a9b7b ("userfaultfd: hugetlbfs: add userfaultfd hugetlb hook") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: syzbot+193f9cee8638750b23cf@syzkaller.appspotmail.com Reported-by: Liu Zixian <liuzixian4@huawei.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: David Hildenbrand <david@redhat.com> Cc: John Hubbard <jhubbard@nvidia.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Sidhartha Kumar <sidhartha.kumar@oracle.com> Cc: <stable@vger.kernel.org> [4.14+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
send zc is not restricted to !IO_URING_F_UNLOCKED anymore and so
we can't use task-tw ordering trick to order notification cqes
with requests completions. In this case leave it alone and let
io_send_zc_cleanup() flush it.
We currently only add a notification CQE when the send succeded, i.e.
cqe.res >= 0. However, it'd be more robust to do buffer notifications
for failed requests as well in case drivers decide do something fanky.
Always return a buffer notification after initial prep, don't hide it.
This behaviour is better aligned with documentation and the patch also
helps the userspace to respect it.
Partial zc send may end up in io_req_complete_failed(), which not only
would return invalid result but also mask out the notification leading
to lifetime issues.
In preparation for using struct io_sr_msg for zerocopy sends, clean up
types. First, flags can be u16 as it's provided by the userspace in u16
ioprio, as well as addr_len. This saves us 4 bytes. Also use unsigned
for size and done_io, both are as well limited to u32.
User space tasks can migrate between CPUs, so when tracing selected CPUs,
system-wide sideband is still needed, however evlist->core.has_user_cpus
is not set in the hybrid case, so check the target cpu_list instead.
Fixes: 7d189cadbeebc778 ("perf intel-pt: Track sideband system-wide when needed") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221012082259.22394-3-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the kernel exposes a new perf_event_attr field in a format attr, perf
will return an error stating the specified PMU can't be found. For
example, a format attr with 'config3:0-63' causes an error as config3 is
unknown to perf. This causes a compatibility issue between a newer
kernel with older perf tool.
Before this change with a kernel adding 'config3' I get:
$ perf record -e arm_spe// -- true
event syntax error: 'arm_spe//'
\___ Cannot find PMU `arm_spe'. Missing kernel support?
Run 'perf list' for a list of valid events
Usage: perf record [<options>] [<command>]
or: perf record [<options>] -- <command> [<options>]
-e, --event <event> event selector. use 'perf list' to list
available events
After this change, I get:
$ perf record -e arm_spe// -- true
WARNING: 'arm_spe_0' format 'inv_event_filter' requires 'perf_event_attr::config3' which is not supported by this version of perf!
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.091 MB perf.data ]
To support unknown configN formats, rework the YACC implementation to
pass any config[0-9]+ format to perf_pmu__new_format() to handle with a
warning.
Reviewed-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Tested-by: Leo Yan <leo.yan@linaro.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: James Clark <james.clark@arm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220914-arm-perf-tool-spe1-2-v2-v4-1-83c098e6212e@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported that RPi3[1] and RPi Zero 2W boards have issues with
the Bluetooth. It turns out that when switching from initial to
operation speed host and device no longer can talk each other because
host uses incorrect UART baud rate.
The UART driver used in this case is amba-pl011. Original fix, see
below Github link[2], was inside pl011 module, but somehow it didn't
look as the right place to fix. Beside that this original rounding
function is not exactly perfect for all possible clock values. So I
deiced to move the hack to the platform which actually need it.
The UART clock is initialised to be as close to the requested
frequency as possible without exceeding it. Now that there is a
clock manager that returns the actual frequencies, an expected
48MHz clock is reported as 47999625. If the requested baud rate
== requested clock/16, there is no headroom and the slight
reduction in actual clock rate results in failure.
If increasing a clock by less than 0.1% changes it from ..999..
to ..000.., round it up.
Cc: Phil Elwell <phil@raspberrypi.com> Signed-off-by: Ivan T. Ivanov <iivanov@suse.de> Reviewed-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220912081306.24662-1-iivanov@suse.de Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Deferred probe is an expected return value for fwnode_usb_role_switch_get().
Given that the driver deals with it properly, there's no need to output a
warning that may potentially confuse users.
--
V2 -> V3: remove the Fixes and Cc
V1 -> V2: adjust the coding style for better reading format.
drivers/usb/typec/ucsi/ucsi.c | 8 +++-----
1 file changed, 3 insertions(+), 5 deletions(-)
Signed-off-by: Wayne Chang <waynec@nvidia.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20220927134512.2651067-1-waynec@nvidia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the dw-edma driver enables the runtime_pm for parent device
(chip->dev) and increments/decrements the refcount during alloc/free
chan resources callbacks.
This leads to a problem when the eDMA driver has been probed, but the
channels were not used. This scenario can happen when the DW PCIe driver
probes eDMA driver successfully, but the PCI EPF driver decides not to
use eDMA channels and use iATU instead for PCI transfers.
In this case, the underlying device would be runtime suspended due to
pm_runtime_enable() in dw_edma_probe() and the PCI EPF driver would have
no knowledge of it.
Ideally, the eDMA driver should not be the one doing the runtime PM of
the parent device. The responsibility should instead belong to the client
drivers like PCI EPF.
So let's remove the runtime PM support from eDMA driver.
Use get_device and put_device in the open and close functions to
make sure the device doesn't get freed while a file descriptor is
open.
Also, lock around the freeing of the device buffer and check the
buffer before using it in the submit function.
Due to the OCC communication design with a shared SRAM area,
checkum errors are expected due to corrupted buffer from OCC
communications with other system components. Therefore, retry
the command twice in the event of a checksum failure.
The hctx's run_work may be racing with the elevator switch when
reinitializing hardware queues. The queue is merely frozen in this
context, but that only prevents requests from allocating and doesn't
stop the hctx work from running. The work may get an elevator pointer
that's being torn down, and can result in use-after-free errors and
kernel panics (example below). Use the quiesced elevator switch instead,
and make the previous one static since it is now only used locally.
In idmouse_create_image, if any ftip_command fails, it will
go to the reset label. However, this leads to the data in
bulk_in_buffer[HEADER..IMGSIZE] uninitialized. And the check
for valid image incurs an uninitialized dereference.
Fix this by moving the check before reset label since this
check only be valid if the data after bulk_in_buffer[HEADER]
has concrete data.
Note that this is found by KMSAN, so only kernel compilation
is tested.
The firmware revision can change on after a reset so copy the most
recent info each time instead of just the first time, otherwise the
sysfs firmware_rev entry may contain stale data.
Reported-by: Jeff Lien <jeff.lien@wdc.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Chao Leng <lengchao@huawei.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a reset occurs after the scan work attempts to issue a command, the
reset may quisce the admin queue, which blocks the scan work's command
from dispatching. The scan work will not be able to complete while the
queue is quiesced.
Meanwhile, the reset work will cancel all outstanding admin tags and
wait until all requests have transitioned to idle, which includes the
passthrough request. But the passthrough request won't be set to idle
until after the scan_work flushes, so we're deadlocked.
Fix this by handling the end effects after the request has been freed.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216354 Reported-by: Jonathan Derrick <Jonathan.Derrick@solidigm.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Chao Leng <lengchao@huawei.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Array of group descriptor block buffers can get rather large. In theory
in can reach 1MB for perfectly valid filesystem and even more for
maliciously crafted ones. Use kvmalloc() to allocate the array to avoid
straining memory allocator with large order allocations unnecessarily.
Reported-by: syzbot+0f2f7e65a3007d39539f@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix this compilation error seen when CONFIG_TRACING is not enabled:
drivers/scsi/qla2xxx/qla_os.c: In function 'qla_trace_init':
drivers/scsi/qla2xxx/qla_os.c:2854:25: error: implicit declaration of function
'trace_array_get_by_name'; did you mean 'trace_array_set_clr_event'?
[-Werror=implicit-function-declaration]
2854 | qla_trc_array = trace_array_get_by_name("qla2xxx");
| ^~~~~~~~~~~~~~~~~~~~~~~
| trace_array_set_clr_event
drivers/scsi/qla2xxx/qla_os.c: In function 'qla_trace_uninit':
drivers/scsi/qla2xxx/qla_os.c:2869:9: error: implicit declaration of function
'trace_array_put' [-Werror=implicit-function-declaration]
2869 | trace_array_put(qla_trc_array);
| ^~~~~~~~~~~~~~~
Link: https://lore.kernel.org/r/20220907233308.4153-2-aeasi@marvell.com Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Arun Easi <aeasi@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In rtw_init_cmd_priv(), if `pcmdpriv->rsp_allocated_buf` is allocated
in failure, then `pcmdpriv->cmd_allocated_buf` will be not properly
released. Besides, considering there are only two error paths and the
first one can directly return, so we do not need implicitly jump to the
`exit` tag to execute the error handler.
So this patch added `kfree(pcmdpriv->cmd_allocated_buf);` on the error
path to release the resource and simplified the return logic of
rtw_init_cmd_priv(). As there is no proper device to test with, no runtime
testing was performed.
In rtw_init_drv_sw(), there are various init functions are called to
populate the padapter structure and some checks for their return value.
However, except for the first one error path, the other five error paths
do not properly release the previous allocated resources, which leads to
various memory leaks.
This patch fixes them and keeps the success and error separate.
Note that these changes keep the form of `rtw_init_drv_sw()` in
"drivers/staging/r8188eu/os_dep/os_intfs.c". As there is no proper device
to test with, no runtime testing was performed.
Overflowing CQEs may result in reordering, which is buggy in case of
links, F_MORE and so on. If we guarantee that we don't reorder for
the unlikely event of a CQ ring overflow, then we can further extend
this to not have to terminate multishot requests if it happens. For
other operations, like zerocopy sends, we have no choice but to honor
CQE ordering.
But the commit affects not only "Samsung Fit Flash" but also other usb
storages that use the same controller and causes severe performance
regression.
# hdparm -t /dev/sda (without the quirk)
Timing buffered disk reads: 622 MB in 3.01 seconds = 206.66 MB/sec
# hdparm -t /dev/sda (with the quirk)
Timing buffered disk reads: 220 MB in 3.00 seconds = 73.32 MB/sec
The commit author mentioned that "Issue was reproduced after device has
bad block", so this quirk should be applied when we have the timeout
issue with a device that has bad blocks.
We revert the commit so that we apply this quirk by adding kernel
paramters using a bootloader or other ways when we really need it,
without the performance regression with devices that don't have the
issue.
When configured in HOST mode, after issuing U3/L2 exit controller fails
to send proper CRC checksum in CRC5 field. Because of this behavior
Transaction Error is generated, resulting in reset and re-enumeration of
usb device attached. Enabling chicken bit 10 of GUCTL1 will correct this
problem.
When this bit is set to '1', the UTMI/ULPI opmode will be changed to
"normal" along with HS terminations, term, and xcvr signals after EOR.
This option is to support certain legacy UTMI/ULPI PHYs.
Added "snps,resume-hs-terminations" quirk to resolved the above issue.
With this set the SOF/ITP counter is based on ref_clk when 2.0 ports are
suspended.
snps,dis-u2-freeclk-exists-quirk can be removed as
snps,gfladj-refclk-lpm-sel also clears the free running clock configuration
bit.
The usb function device call musb_gadget_queue() adds the passed
request to musb_ep::req_list,If the (request->length > musb_ep->packet_sz)
and (is_buffer_mapped(req) return false),the rxstate() will copy all data
in fifo to request->buf which may cause request->buf out of bounds.
Fix it by add the length check :
fifocnt = min_t(unsigned, request->length - request->actual, fifocnt);
xhci_alloc_stream_info() allocates stream context array for stream_info
->stream_ctx_array with xhci_alloc_stream_ctx(). When some error occurs,
stream_info->stream_ctx_array is not released, which will lead to a
memory leak.
We can fix it by releasing the stream_info->stream_ctx_array with
xhci_free_stream_ctx() on the error path to avoid the potential memory
leak.
A complicated deadlock exists when using the journal and an elevated
group_thrtead_cnt. It was found with loop devices, but its not clear
whether it can be seen with real disks. The deadlock can occur simply
by writing data with an fio script.
When the deadlock occurs, multiple threads will hang in different ways:
1) The group threads will hang in the blk-wbt code with bios waiting to
be submitted to the block layer:
However, before hanging, the MD_SB_CHANGE_PENDING flag will be
set for sb_flags in r5l_write_super_and_discard_space(). This
flag will never be cleared because the submit_bio() call never
returns.
3) Due to the MD_SB_CHANGE_PENDING flag being set, handle_stripe()
will do no processing on any pending stripes and re-set
STRIPE_HANDLE. This will cause the raid5d thread to enter an
infinite loop, constantly trying to handle the same stripes
stuck in the queue.
The raid5d thread has a blk_plug that holds a number of bios
that are also stuck waiting seeing the thread is in a loop
that never schedules. These bios have been accounted for by
blk-wbt thus preventing the other threads above from
continuing when they try to submit bios. --Deadlock.
To fix this, add the same wait_event() that is used in raid5_do_work()
to raid5d() such that if MD_SB_CHANGE_PENDING is set, the thread will
schedule and wait until the flag is cleared. The schedule action will
flush the plug which will allow the r5l_reclaim thread to continue,
thus preventing the deadlock.
However, md_check_recovery() calls can also clear MD_SB_CHANGE_PENDING
from the same thread and can thus deadlock if the thread is put to
sleep. So avoid waiting if md_check_recovery() is being called in the
loop.
It's not clear when the deadlock was introduced, but the similar
wait_event() call in raid5_do_work() was added in 2017 by this
commit:
16d997b78b15 ("md/raid5: simplfy delaying of writes while metadata
is updated.")
Arne Wendt writes:
Cheap clone controllers may (falsely) report as having a user
calibration for the analog sticks in place, but return
wrong/impossible values for the actual calibration data.
In the present case at mine, the controller reports having a
user calibration in place and successfully executes the read
commands. The reported user calibration however is
min = center = max = 0.
This pull request addresses problems of this kind by checking the
provided user calibration-data for plausibility (min < center < max)
and falling back to the default values if implausible.
I'll note that I was experiencing a crash because of this bug when using
the GuliKit KingKong 2 controller. The crash manifests as a divide by
zero error in the kernel logs:
kernel: divide error: 0000 [#1] PREEMPT SMP NOPTI
ssip_pn_open() claims the HSI client's port with hsi_claim_port(). When
hsi_register_port_event() gets some error and returns a negetive value,
the HSI client's port should be released with hsi_release_port().
Fix it by calling hsi_release_port() when hsi_register_port_event() fails.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
new_value = kmemdup(data, device->report_size, GFP_ATOMIC);
if (!new_value)
return -ENOMEM;
report = &device->cbuf[device->cbuf_end];
/* passing NULL is safe */
kfree(report->value);
...
The registered report is stored in the struct roccat_device member
"struct roccat_report cbuf[ROCCAT_CBUF_SIZE];".
If more reports are received than the "ROCCAT_CBUF_SIZE" value,
kfree() the saved report from cbuf[0] and allocates a new reprot.
Since there is no lock when this kfree() is performed,
kfree() can be performed even while reading the saved report.
report = &device->cbuf[reader->cbuf_start];
/*
* If report is larger than requested amount of data, rest of report
* is lost!
*/
len = device->report_size > count ? count : device->report_size;
The roccat_read() function receives the device->cbuf report and
delivers it to the user through copy_to_user().
If the N+ROCCAT_CBUF_SIZE th report is received while copying of
the Nth report->value is in progress, the pointer that copy_to_user()
is working on is kfree()ed and UAF read may occur. (race condition)
Since the device node of this driver does not set separate permissions,
this is not a security vulnerability, but because it is used for
requesting screen display of profile or dpi settings,
a user using the roccat device can apply udev to this device node or
There is a possibility to use it by giving.
The Topre REALFORCE R2 firmware incorrectly reports that interface
descriptor number 1, input report descriptor 2's events are array events
rather than variable events. That particular report descriptor is used
to report keypresses when there are more than 6 keys held at a time.
This bug prevents events from this interface from being registered
properly, so only 6 keypresses (from a different interface) can be
registered at once, rather than full n-key rollover.
This commit fixes the bug by setting the correct value in a report_fixup
function.
The call to intel_register_dai() may fail because of memory allocation
issues or problems reported by the ASoC core. In all cases, when a
error is thrown the component is not registered, it's invalid to
unregister it.
The buf passed in struct sdw_msg must only be written for a READ,
in that case the RDATA part of the response is the data value of the
register.
For a write command there is no RDATA, and buf should be assumed to
be const and unmodifable. The original caller should not expect its data
buffer to be corrupted by an sdw_nwrite().
Inside set_at_max_writeback_rate() the calculation in following if()
check is wrong,
if (atomic_inc_return(&c->idle_counter) <
atomic_read(&c->attached_dev_nr) * 6)
Because each attached backing device has its own writeback thread
running and increasing c->idle_counter, the counter increates much
faster than expected. The correct calculation should be,
(counter / dev_nr) < dev_nr * 6
which equals to,
counter < dev_nr * dev_nr * 6
This patch fixes the above mistake with correct calculation, and helper
routine idle_counter_exceeded() is added to make code be more clear.
Reported-by: Mingzhe Zou <mingzhe.zou@easystack.cn> Signed-off-by: Coly Li <colyli@suse.de> Acked-by: Mingzhe Zou <mingzhe.zou@easystack.cn> Link: https://lore.kernel.org/r/20220919161647.81238-6-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Having greater than AHCI_MAX_PORTS (32) ports detected isn't that critical
from the further AHCI-platform initialization point of view since
exceeding the ports upper limit will cause allocating more resources than
will be used afterwards. But detecting too many child DT-nodes doesn't
seem right since it's very unlikely to have it on an ordinary platform. In
accordance with the AHCI specification there can't be more than 32 ports
implemented at least due to having the CAP.NP field of 5 bits wide and the
PI register of dword size. Thus if such situation is found the DTB must
have been corrupted and the data read from it shouldn't be reliable. Let's
consider that as an erroneous situation and halt further resources
allocation.
Note it's logically more correct to have the nports set only after the
initialization value is checked for being sane. So while at it let's make
sure nports is assigned with a correct value.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a problem found by code review in tg_with_in_bps_limit() that
'bps_limit * jiffy_elapsed_rnd' might overflow. Fix the problem by
calling mul_u64_u64_div_u64() instead.
In function device_init_td0_ring, memory is allocated for member
td_info of priv->apTD0Rings[i], with i increasing from 0. In case of
allocation failure, the memory is freed in reversed order, with i
decreasing to 0. However, the case i=0 is left out and thus memory is
leaked.
Modify the memory freeing loop to include the case i=0.
Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Signed-off-by: Nam Cao <namcaov@gmail.com> Link: https://lore.kernel.org/r/20220909141338.19343-1-namcaov@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ADP5061_CHG_STATUS_1_CHG_STATUS is masked with 0x07, which means a length
of 8, but adp5061_chg_type array size is 4, may end up reading 4 elements
beyond the end of the adp5061_chg_type[] array.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch is changing the simple workqueue in the gadget driver to be
allocated as async_wq with a higher priority. The pump worker, that is
filling the usb requests, will have a higher priority and will not be
scheduled away so often while the video stream is handled. This will
lead to fewer streaming underruns.
The DMA operations of HiSilicon PTT device can only work properly with
identical mappings. So add a quirk for the device to force the domain
as passthrough.
Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Reviewed-by: John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/r/20220816114414.4092-2-yangyicong@huawei.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported hung task [1]. The following program is a simplified
version of the reproducer:
int main(void)
{
int sv[2], fd;
if (socketpair(AF_UNIX, SOCK_STREAM, 0, sv) < 0)
return 1;
if ((fd = open("/dev/nbd0", 0)) < 0)
return 1;
if (ioctl(fd, NBD_SET_SIZE_BLOCKS, 0x81) < 0)
return 1;
if (ioctl(fd, NBD_SET_SOCK, sv[0]) < 0)
return 1;
if (ioctl(fd, NBD_DO_IT) < 0)
return 1;
return 0;
}
When signal interrupt nbd_start_device_ioctl() waiting the condition
atomic_read(&config->recv_threads) == 0, the task can hung because it
waits the completion of the inflight IOs.
This patch fixes the issue by clearing queue, not just shutdown, when
signal interrupt nbd_start_device_ioctl().
The original code will "goto out_disable_device" and call
pci_disable_device() if pci_enable_device() fails. The kernel will generate
a warning message like "3w-9xxx 0000:00:05.0: disabling already-disabled
device".
We shouldn't disable a device that failed to be enabled. A simple return is
fine.
Link: https://lore.kernel.org/r/20220829110115.38789-1-fantasquex@gmail.com Reported-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Letu Ren <fantasquex@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
UDMA_CHAN_RT_*BCNT_REG stores the real-time channel bytecount statistics.
These registers are 32-bit hardware counters and the driver uses these
counters to monitor the operational progress status for a channel, when
transferring more than 4GB of data it was observed that these counters
overflow and completion calculation of a operation gets affected and the
transfer hangs indefinitely.
This commit adds changes to decrease the byte count for every complete
transaction so that these registers never overflow and the proper byte
count statistics is maintained for ongoing transaction by the RT counters.
Earlier uc->bcnt used to maintain a count of the completed bytes at driver
side, since the RT counters maintain the statistics of current transaction
now, the maintenance of uc->bcnt is not necessary.
An error case exit from lpfc_cmpl_ct_cmd_gft_id() results in a call to
lpfc_nlp_put() with a null pointer to a nodelist structure.
Changed lpfc_cmpl_ct_cmd_gft_id() to initialize nodelist pointer upon
entry.
Link: https://lore.kernel.org/r/20220819011736.14141-3-jsmart2021@gmail.com Co-developed-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: Justin Tee <justin.tee@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The xhci_plat_brcm xhci block can enter suspend with clock disabled to save
power and re-enable them on resume. Make use of the XHCI_SUSPEND_RESUME_CLKS
quirk to do so.
Introduce XHCI_SUSPEND_RESUME_CLKS quirk as a means to suspend and resume
clocks if the hardware is capable of doing so. We assume that clocks will
be needed if the device may wake.
An incoming Read request causes multiple Read responses. If a user MR to
copy data from is unavailable or responder cannot send a reply, then the
error messages can be printed for each response attempt, resulting in
message overflow.
The function zynqmp_pll_round_rate is used to find a most appropriate
PLL frequency which the hardware can generate according to the desired
frequency. For example, if the desired frequency is 297MHz, considering
the limited range from PS_PLL_VCO_MIN (1.5GHz) to PS_PLL_VCO_MAX (3.0GHz)
of PLL, zynqmp_pll_round_rate should return 1.872GHz (297MHz * 5).
There are two problems with the current code of zynqmp_pll_round_rate:
1) When the rate is below PS_PLL_VCO_MIN, it can't find a correct rate
when the parameter "rate" is an integer multiple of *prate, in other words,
if "f" is zero, zynqmp_pll_round_rate won't return a valid frequency which
is from PS_PLL_VCO_MIN to PS_PLL_VCO_MAX. For example, *prate is 33MHz
and the rate is 660MHz, zynqmp_pll_round_rate will not boost up rate and
just return 660MHz, and this will cause clk_calc_new_rates failure since
zynqmp_pll_round_rate returns an invalid rate out of its boundaries.
2) Even if the rate is higher than PS_PLL_VCO_MIN, there is still a risk
that zynqmp_pll_round_rate returns an invalid rate because the function
DIV_ROUND_CLOSEST makes some loss in the fractional part. If the parent
clock *prate is 33333333Hz and we want to set the PLL rate to 1.5GHz,
this function will return 1499999985Hz by using the formula below:
value = *prate * DIV_ROUND_CLOSEST(rate, *prate)).
This value is also invalid since it's slightly smaller than PS_PLL_VCO_MIN.
because DIV_ROUND_CLOSEST makes some loss in the fractional part.
When the driver calls cx88_risc_buffer() to prepare the buffer, the
function call may fail, resulting in a empty buffer and null-ptr-deref
later in buffer_queue().
"BUG: KASAN: stack-out-of-bounds in strncpy+0x30/0x68"
Linux-ATF interface is using 16 bytes of SMC payload. In case clock name is
longer than 15 bytes, string terminated NULL character will not be received
by Linux. Add explicit NULL character at last byte to fix issues when clock
name is longer.
This fixes below bug reported by KASAN:
==================================================================
BUG: KASAN: stack-out-of-bounds in strncpy+0x30/0x68
Read of size 1 at addr ffff0008c89a7410 by task swapper/0/1
In case CONFIG_KASAN_VMALLOC=y kasan_populate_vmalloc() allocates the
shadow pages dynamically. But even worse is that kasan_release_vmalloc()
releases them, which is not compatible with create_mapping() of
MODULES_VADDR..MODULES_END range:
BUG: Bad page state in process kworker/9:1 pfn:2068b
page:e5e06160 refcount:0 mapcount:0 mapping:00000000 index:0x0
flags: 0x1000(reserved)
raw: 00001000e5e06164e5e06164000000000000000000000000ffffffff00000000
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags: 0x1000(reserved)
Modules linked in: ip_tables
CPU: 9 PID: 154 Comm: kworker/9:1 Not tainted 5.4.188-... #1
Hardware name: LSI Axxia AXM55XX
Workqueue: events do_free_init
unwind_backtrace
show_stack
dump_stack
bad_page
free_pcp_prepare
free_unref_page
kasan_depopulate_vmalloc_pte
__apply_to_page_range
apply_to_existing_page_range
kasan_release_vmalloc
__purge_vmap_area_lazy
_vm_unmap_aliases.part.0
__vunmap
do_free_init
process_one_work
worker_thread
kthread
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because an exception stack frame is not created in the exception entry,
save_trace() does special handling for the exception PC, but this is
only needed when CONFIG_FRAME_POINTER_UNWIND=y. When
CONFIG_ARM_UNWIND=y, unwind annotations have been added to the exception
entry and save_trace() will repeatedly save the exception PC:
When using the frame pointer unwinder, it was found that the stack trace
output of stack_trace_save() is incomplete if the stack contains
call_with_stack():
For the frame pointer unwinder, unwind_frame() checks stackframe::fp by
stackframe::sp. Since call_with_stack() switches the SP from one stack
to another, stackframe::fp and stackframe: :sp will point to different
stacks, so we can no longer check stackframe::fp by stackframe::sp. Skip
checking stackframe::fp at this point to avoid this problem.
Signed-off-by: Li Huafei <lihuafei1@huawei.com> Reviewed-by: Linus Waleij <linus.walleij@linaro.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We have a temporary free space ctl for loading the free space cache in
order to avoid having allocations happening while we're loading the
cache. When we hit an error we free it all up, however this also calls
btrfs_discard_update_discardable, which requires
block_group->free_space_ctl->tree_lock to be held. However this is our
temporary ctl so this lock isn't held. Fix this by calling
__btrfs_remove_free_space_cache_locked instead so that we only clean up
the entries and do not mess with the discardable stats.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
btrfs currently prints information about space cache or free space tree
being in use on every remount, regardless whether such remount actually
enabled or disabled one of these features.
This is actually unnecessary since providing remount options changing the
state of these features will explicitly print the appropriate notice.
Let's instead print such unconditional information just on an initial mount
to avoid filling the kernel log when, for example, laptop-mode-tools
remount the fs on some events.
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The first scrub reports the super error correctly:
scrub done for f3289218-abd3-41ac-a630-202f766c0859
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
But the second read-only scrub still reports the same super error:
Scrub started: Tue Aug 2 14:44:11 2022
Status: finished
Duration: 0:00:00
Total to scrub: 1.26GiB
Rate: 0.00B/s
Error summary: super=1
Corrected: 0
Uncorrectable: 0
Unverified: 0
[CAUSE]
The comments already shows that super block can be easily fixed by
committing a transaction:
/*
* If we find an error in a super block, we just report it.
* They will get written with the next transaction commit
* anyway
*/
But the truth is, such assumption is not always true, and since scrub
should try to repair every error it found (except for read-only scrub),
we should really actively commit a transaction to fix this.
[FIX]
Just commit a transaction if we found any super block errors, after
everything else is done.
We cannot do this just after scrub_supers(), as
btrfs_commit_transaction() will try to pause and wait for the running
scrub, thus we can not call it with scrub_lock hold.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike data/metadata corruption, if scrub detected some error in the
super block, the only error message is from the updated device status:
BTRFS info (device dm-1): scrub: started on devid 2
BTRFS error (device dm-1): bdev /dev/mapper/test-scratch2 errs: wr 0, rd 0, flush 0, corrupt 1, gen 0
BTRFS info (device dm-1): scrub: finished on devid 2 with status: 0
This is not helpful at all.
[CAUSE]
Unlike data/metadata error reporting, there is no visible report in
kernel dmesg to report supper block errors.
In fact, return value of scrub_checksum_super() is intentionally
skipped, thus scrub_handle_errored_block() will never be called for
super blocks.
[FIX]
Make super block errors to output an error message, now the full
dmesg would looks like this:
BTRFS info (device dm-1): scrub: started on devid 2
BTRFS warning (device dm-1): super block error on device /dev/mapper/test-scratch2, physical 67108864
BTRFS error (device dm-1): bdev /dev/mapper/test-scratch2 errs: wr 0, rd 0, flush 0, corrupt 1, gen 0
BTRFS info (device dm-1): scrub: finished on devid 2 with status: 0
BTRFS info (device dm-1): scrub: started on devid 2
This fix involves:
- Move the super_errors reporting to scrub_handle_errored_block()
This allows the device status message to show after the super block
error message.
But now we no longer distinguish super block corruption and generation
mismatch, now all counted as corruption.
- Properly check the return value from scrub_checksum_super()
- Add extra super block error reporting for scrub_print_warning().
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is an internal report on hitting the following ASSERT() in
recalculate_thresholds():
ASSERT(ctl->total_bitmaps <= max_bitmaps);
Above @max_bitmaps is calculated using the following variables:
- bytes_per_bg
8 * 4096 * 4096 (128M) for x86_64/x86.
- block_group->length
The length of the block group.
@max_bitmaps is the rounded up value of block_group->length / 128M.
Normally one free space cache should not have more bitmaps than above
value, but when it happens the ASSERT() can be triggered if
CONFIG_BTRFS_ASSERT is also enabled.
But the ASSERT() itself won't provide enough info to know which is going
wrong.
Is the bg too small thus it only allows one bitmap?
Or is there something else wrong?
So although I haven't found extra reports or crash dump to do further
investigation, add the extra info to make it more helpful to debug.
Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This allows the userspace to notice that there's not enough
current provided to charge the battery, and also fixes issues
with 0% SOC values being considered invalid.
Signed-off-by: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm> Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turns out that it is not necessary to declare the VSELECT signal as
GPIO and let the PMIC driver set it to a fixed high level. This switches
the voltage between 3.3V and 1.8V by setting the PMIC register for LDO5
accordingly.
Instead we can do it like other boards already do and simply mux the
VSELECT signal of the USDHC interface to the pin. This makes sure that
the correct voltage is selected by setting the PMIC's SD_VSEL input
to high or low accordingly.
When arm64 signal context data overflows the base struct sigcontext it gets
placed in an extra buffer pointed to by a record of type EXTRA_CONTEXT in
the base struct sigcontext which is required to be the last record in the
base struct sigframe. The current validation code attempts to check this
by using GET_RESV_NEXT_HEAD() to step forward from the current record to
the next but that is a macro which assumes it is being provided with a
struct _aarch64_ctx and uses the size there to skip forward to the next
record. Instead validate_extra_context() passes it a struct extra_context
which has a separate size field. This compiles but results in us trying
to validate a termination record in completely the wrong place, at best
failing validation and at worst just segfaulting. Fix this by passing
the struct _aarch64_ctx we meant to into the macro.
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property
Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,
[17:19:39.183] event1 - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1 - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1 - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1 - not using input device '/dev/input/event1'
This will then cause the APP weston-touch-calibrator can't list touch devices.
root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.
And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.
In most cases this is related to fsl,err006687-workaround-present, which
requires a GPIO interrupt next a GIC interrupt.
This fixes the dtbs_check warning:
imx6dl-mba6a.dtb: ethernet@2188000: More than one condition true in oneOf schema:
{'$filename': 'Documentation/devicetree/bindings/net/fsl,fec.yaml',
[...]
This was fixed in initialize_cpsch before, but not in initialize_nocpsch.
Factor sdma bitmap initialization into a helper function to apply the
correct implementation in both cases without duplicating it.
v2: Added a range check
Reported-by: Ellis Michael <ellis@ellismichael.com> Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Graham Sider <Graham.Sider@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
vid stream control is double bufferred, if we don't wait for video
stream enable set to 0, we may get temporary image corruption
showing on the stream when setting PIXEL_TO_SYMBOL_FIFO_ENABLE to 0.
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com> Acked-by: Jasdeep Dhillon <jdhillon@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sequence for Source DP PHY CTS automation is [2][1]:
1- Emulate successful Link Training(LT)
2- Short HPD and change link rates and number of lanes by LT.
(This is same flow for Link Layer CTS)
3- Short HPD and change PHY test pattern and swing/pre-emphasis
levels (This step should not trigger LT)
The problem is with DP PHY compliance setup as follow:
At step 3, before writing TRAINING_LANEx_SET/LINK_QUAL_PATTERN_SET
to declare the pattern/swing requested by scope, we write link
config in LINK_BW_SET/LANE_COUNT_SET on a port that has LTTPR.
As LTTPR snoops aux transaction, LINK_BW_SET/LANE_COUNT_SET writes
indicate a LT will start [Check DP 2.0 E11 -Sec 3.6.8.2 & 3.6.8.6.3],
and LTTPR will reset the link and stop sending DP signals to
DPTX/Scope causing the measurements to fail. Note that step 3 will
not trigger LT and DP link will never recovered by the
Aux Emulator/Scope.
The reset of link can be tested with a monitor connected to LTTPR
port simply by writing to LINK_BW_SET or LANE_COUNT_SET as follow
This single aux write causes the screen to blank, sending short HPD to
DPTX, setting LINK_STATUS_UPDATE = 1 in DPCD 0x204, and triggering LT.
As stated in [1]:
"Before any TX electrical testing can be performed, the link between a
DPTX and DPRX (in this case, a piece of test equipment), including all
LTTPRs within the path, shall be trained as defined in this Standard."
In addition, changing Phy pattern/Swing/Pre-emphasis (Step 3) uses the
same link rate and lane count applied on step 2, so no need to redo LT.
The fix is to not rewrite link config in step 3, and just writes
TRAINING_LANEx_SET and LINK_QUAL_PATTERN_SET