The commit 855a40cd8ccc ("spi: cadence: Add SPI transfer delays") adds a
delay after each transfer into the driver's transfer_one(). However,
the delay is already done in SPI core. So this commit unnecessarily
doubles the delay amount. Revert this commit.
Chris reported that a Dell PowerEdge T340 system stopped to boot when upgrading
to a kernel which contains the parallel hotplug changes. Disabling parallel
hotplug on the kernel command line makes it boot again.
It turns out that the Dell BIOS has x2APIC enabled and the boot CPU comes up in
X2APIC mode, but the APs come up inconsistently in xAPIC mode.
Parallel hotplug requires that the upcoming CPU reads out its APIC ID from the
local APIC in order to map it to the Linux CPU number.
In this particular case the readout on the APs uses the MMIO mapped registers
because the BIOS failed to enable x2APIC mode. That readout results in a page
fault because the kernel does not have the APIC MMIO space mapped when X2APIC
mode was enabled by the BIOS on the boot CPU and the kernel switched to X2APIC
mode early. That page fault can't be handled on the upcoming CPU that early and
results in a silent boot failure.
If parallel hotplug is disabled the system boots because in that case the APIC
ID read is not required as the Linux CPU number is provided to the AP in the
smpboot control word. When the kernel uses x2APIC mode then the APs are
switched to x2APIC mode too slightly later in the bringup process, but there is
no reason to do it that late.
Cure the BIOS bogosity by checking in the parallel bootup path whether the
kernel uses x2APIC mode and if so switching over the APs to x2APIC mode before
the APIC ID readout.
Fixes: 0c7ffa32dbd6 ("x86/smpboot/64: Implement arch_cpuhp_init_parallel_bringup() and enable it") Reported-by: Chris Lindee <chris.lindee@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Reviewed-by: Ashok Raj <ashok.raj@intel.com> Tested-by: Chris Lindee <chris.lindee@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/CA%2B2tU59853R49EaU_tyvOZuOTDdcU0RshGyydccp9R1NX9bEeQ@mail.gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
apply_alternatives() treats alternatives with the ALT_FLAG_NOT flag set
special as it optimizes the existing NOPs in place.
Unfortunately, this happens with interrupts enabled and does not provide any
form of core synchronization.
So an interrupt hitting in the middle of the update and using the affected code
path will observe a half updated NOP and crash and burn. The following
3 NOP sequence was observed to expose this crash halfway reliably under QEMU
32bit:
That's not really correct because the synchronization should happen before
interrupts are re-enabled to ensure that a pending interrupt observes the
complete update of the opcodes.
It's not entirely clear whether the interrupt entry provides enough
serialization already, but moving the sync_core() invocation into interrupt
disabled region does no harm and is obviously correct.
Fixes: 6fffacb30349 ("x86/alternatives, jumplabel: Use text_poke_early() before mm_init()") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: <stable@kernel.org> Link: https://lore.kernel.org/r/ZT6narvE%2BLxX%2B7Be@windriver.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When failing to create a vcpu because (for example) it has a
duplicate vcpu_id, we destroy the vcpu. Amusingly, this leaves
the redistributor registered with the KVM_MMIO bus.
This is no good, and we should properly clean the mess. Force
a teardown of the vgic vcpu interface, including the RD device
before returning to the caller.
As we are going to need to call into kvm_vgic_vcpu_destroy() without
prior holding of the slots_lock, introduce __kvm_vgic_vcpu_destroy()
as a non-locking primitive of kvm_vgic_vcpu_destroy().
When destroying a vgic, we have rather cumbersome rules about
when slots_lock and config_lock are held, resulting in fun
buglets.
The first port of call is to simplify kvm_vgic_map_resources()
so that there is only one call to kvm_vgic_destroy() instead of
two, with the second only holding half of the locks.
For that, we kill the non-locking primitive and move the call
outside of the locking altogether. This doesn't change anything
(we re-acquire the locks and teardown the whole vgic), and
simplifies the code significantly.
The dentry returned by debugfs_lookup() needs to be released by calling
dput() which is missing in margining_port_remove(). Fix this by calling
debugfs_lookup_and_remove() that combines both and avoids the memory leak.
Fixes: d0f1e0c2a699 ("thunderbolt: Add support for receiver lane margining") Cc: stable@vger.kernel.org Signed-off-by: Yaxiong Tian <tianyaxiong@kylinos.cn> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A refcount issue can appeared in __fwnode_link_del() due to the
pr_debug() call:
WARNING: CPU: 0 PID: 901 at lib/refcount.c:25 refcount_warn_saturate+0xe5/0x110
Call Trace:
<TASK>
...
of_node_get+0x1e/0x30
of_fwnode_get+0x28/0x40
fwnode_full_name_string+0x34/0x90
fwnode_string+0xdb/0x140
...
vsnprintf+0x17b/0x630
...
__fwnode_link_del+0x25/0xa0
fwnode_links_purge+0x39/0xb0
of_node_release+0xd9/0x180
...
Indeed, an fwnode (of_node) is being destroyed and so, of_node_release()
is called because the of_node refcount reached 0.
From of_node_release() several function calls are done and lead to
a pr_debug() calls with %pfwf to print the fwnode full name.
The issue is not present if we change %pfwf to %pfwP.
To print the full name, %pfwf iterates over the current node and its
parents and obtain/drop a reference to all nodes involved.
In order to allow to print the full name (%pfwf) of a node while it is
being destroyed, do not obtain/drop a reference to this current node.
Fixes: a92eb7621b9f ("lib/vsprintf: Make use of fwnode API to obtain node names and separators") Cc: stable@vger.kernel.org Signed-off-by: Herve Codina <herve.codina@bootlin.com> Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Petr Mladek <pmladek@suse.com> Link: https://lore.kernel.org/r/20231114152655.409331-1-herve.codina@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the hardware implementation of the I2C HID driver based on DesignWare
GPIO IRQ chip, when the user continues to use the I2C HID device in the
suspend process, the I2C HID interrupt will be masked after the resume
process is finished.
This is because the disable_irq()/enable_irq() of the DesignWare GPIO
driver does not synchronize the IRQ mask register state. In normal use
of the I2C HID procedure, the GPIO IRQ irq_mask()/irq_unmask() functions
are called in pairs. In case of an exception, i2c_hid_core_suspend()
calls disable_irq() to disable the GPIO IRQ. With low probability, this
causes irq_unmask() to not be called, which causes the GPIO IRQ to be
masked and not unmasked in enable_irq(), raising an exception.
Add synchronization to the masked register state in the
dwapb_irq_enable()/dwapb_irq_disable() function. mask the GPIO IRQ
before disabling it. After enabling the GPIO IRQ, unmask the IRQ.
Fixes: 7779b3455697 ("gpio: add a driver for the Synopsys DesignWare APB GPIO block") Cc: stable@kernel.org Co-developed-by: Riwen Lu <luriwen@kylinos.cn> Signed-off-by: Riwen Lu <luriwen@kylinos.cn> Signed-off-by: xiongxin <xiongxin@kylinos.cn> Acked-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 34539b442b3b ("bus: ti-sysc: Flush posted write on enable before
reset") caused a regression reproducable on omap4 duovero where the ISS
target module can produce interconnect errors on boot. Turns out the
registers are not accessible until after a delay for devices needing
a ti,sysc-delay-us value.
Let's fix this by flushing the posted write only after the reset delay.
We do flushing also for ti,sysc-delay-us using devices as that should
trigger an interconnect error if the delay is not properly configured.
Let's also add some comments while at it.
Fixes: 34539b442b3b ("bus: ti-sysc: Flush posted write on enable before reset") Cc: stable@vger.kernel.org Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver always registers pin configurations in device tree. This can
cause some inconvenience to users, as pin configurations in the base
device tree cannot be disabled in the device tree overlay, even when the
relevant devices are not used.
Ignore disabled pin configuration nodes in device tree.
The driver always registers pin configurations in device tree. This can
cause some inconvenience to users, as pin configurations in the base
device tree cannot be disabled in the device tree overlay, even when the
relevant devices are not used.
Ignore disabled pin configuration nodes in device tree.
MPC backups tests will skip unexpected sometimes (For example, when
compiling kernel with an older version of gcc, such as gcc-8), since
static functions like mptcp_subflow_send_ack also be listed in
/proc/kallsyms, with a 't' in front of it, not 'T' ('T' is for a global
function):
In this case, mptcp_lib_kallsyms_doesnt_have "mptcp_subflow_send_ack$"
will be false, MPC backups tests will skip. This is not what we expected.
The correct logic here should be: if mptcp_subflow_send_ack is not a
global function in /proc/kallsyms, do these MPC backups tests. So a 'T'
must be added in front of mptcp_subflow_send_ack.
Fixes: 632978f0a961 ("selftests: mptcp: join: skip MPC backups tests if not supported") Cc: stable@vger.kernel.org Signed-off-by: Geliang Tang <geliang.tang@linux.dev> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts <matttbe@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__bio_for_each_segment assumes that the first struct bio_vec argument
doesn't change - it calls "bio_advance_iter_single((bio), &(iter),
(bvl).bv_len)" to advance the iterator. Unfortunately, the dm-integrity
code changes the bio_vec with "bv.bv_len -= pos". When this code path
is taken, the iterator would be out of sync and dm-integrity would
report errors. This happens if the machine is out of memory and
"kmalloc" fails.
Fix this bug by making a copy of "bv" and changing the copy instead.
The synth_event_gen_test module can be built in, if someone wants to run
the tests at boot up and not have to load them.
The synth_event_gen_test_init() function creates and enables the synthetic
events and runs its tests.
The synth_event_gen_test_exit() disables the events it created and
destroys the events.
If the module is builtin, the events are never disabled. The issue is, the
events should be disable after the tests are run. This could be an issue
if the rest of the boot up tests are enabled, as they expect the events to
be in a known state before testing. That known state happens to be
disabled.
When CONFIG_SYNTH_EVENT_GEN_TEST=y and CONFIG_EVENT_TRACE_STARTUP_TEST=y
a warning will trigger:
This is because the synth_event_gen_test_init() left the synthetic events
that it created enabled. By having it disable them after testing, the
other selftests will run fine.
Link: https://lore.kernel.org/linux-trace-kernel/20231220111525.2f0f49b0@gandalf.local.home Cc: stable@vger.kernel.org Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Tom Zanussi <zanussi@kernel.org> Fixes: 9fe41efaca084 ("tracing: Add synth event generation test module") Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Reported-by: Alexander Graf <graf@amazon.com> Tested-by: Alexander Graf <graf@amazon.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8930a6c20791 ("scsi: core: add support for request batching") the
block layer bd->last flag was mapped to SCMD_LAST and used as an indicator
to send the batch for the drivers that implement this feature. However, the
error handling code was not updated accordingly.
scsi_send_eh_cmnd() is used to send error handling commands and request
sense. The problem is that request sense comes as a single command that
gets into the batch queue and times out. As a result the device goes
offline after several failed resets. This was observed on virtio_scsi
during a device resize operation.
To fix this always set SCMD_LAST flag in scsi_send_eh_cmnd() and
scsi_reset_ioctl().
Fixes: 8930a6c20791 ("scsi: core: add support for request batching") Cc: <stable@vger.kernel.org> Signed-off-by: Alexander Atanasov <alexander.atanasov@virtuozzo.com> Link: https://lore.kernel.org/r/20231215121008.2881653-1-alexander.atanasov@virtuozzo.com Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several reports have been made indicating that this commit caused
hangs. Numerous attempts at root causing and fixing the issue have
been unsuccessful so let's revert for now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217599 Cc: <stable@vger.kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver uses MMIO access for reading NVRAM from a flash device.
Underneath there is a flash controller that reads data and provides
mapping window.
Using MMIO interface affects controller configuration and may break real
controller driver. It was reported by multiple users of devices with
NVRAM stored on NAND.
Modify driver to read & cache NVRAM content during init and use that
copy to provide NVMEM data when requested. On NAND flashes due to their
alignment NVRAM partitions can be quite big (1 MiB and more) while
actual NVRAM content stays quite small (usually 16 to 32 KiB). To avoid
allocating so much memory check for actual data length.
The current Atmel SPI controller driver (v2) behaves incorrectly when
using two SPI devices with different clock polarities and GPIO CS.
When switching from one device to another, the controller driver first
enables the CS and then applies whatever configuration suits the targeted
device (typically, the polarities). The side effect of such order is the
apparition of a spurious clock edge after enabling the CS when the clock
polarity needs to be inverted wrt. the previous configuration of the
controller.
This parasitic clock edge is problematic when the SPI device uses that edge
for internal processing, which is perfectly legitimate given that its CS
was asserted. Indeed, devices such as HVS8080 driven by driver gpio-sr in
the kernel are shift registers and will process this first clock edge to
perform a first register shift. In this case, the first bit gets lost and
the whole data block that will later be read by the kernel is all shifted
by one.
Current behavior:
The actual switching of the clock polarity only occurs after the CS
when the controller sends the first message:
^ ^ ^
| | |
| | Actual clock of the message sent
| |
| Change of clock polarity, which occurs with the first
| write to the bus. This edge occurs when the CS is
| already asserted, and can be interpreted as
| the first clock edge by the receiver.
|
GPIO CS toggle
This issue is specific to this controller because while the SPI core
performs the operations in the right order, the controller however does
not. In practice, the controller only applies the clock configuration right
before the first transmission.
So this is not a problem when using the controller's dedicated CS, as the
controller does things correctly, but it becomes a problem when you need to
change the clock polarity and use an external GPIO for the CS.
One possible approach to solve this problem is to send a dummy message
before actually activating the CS, so that the controller applies the clock
polarity beforehand.
CS -\/-----------------------\
|| |
\/ \---------------------
^ ^ ^ ^ ^
| | | | |
| | | | Expected clock cycles when
| | | | sending the message
| | | |
| | | Actual GPIO CS activation, occurs inside
| | | the driver
| | |
| | Dummy message, to trigger clock polarity
| | reconfiguration. This message is not received and
| | processed by the device because CS is low.
| |
| Change of clock polarity, forced by the dummy message. This
| time, the edge is not detected by the receiver.
|
This small spike in CS activation is due to the fact that the
spi-core activates the CS gpio before calling the driver's
set_cs callback, which deactivates this gpio again until the
clock polarity is correct.
To avoid having to systematically send a dummy packet, the driver keeps
track of the clock's current polarity. In this way, it only sends the dummy
packet when necessary, ensuring that the clock will have the correct
polarity when the CS is toggled.
There could be two hardware problems with this patch:
1- Maybe the small CS activation peak can confuse SPI devices
2- If on a design, a single wire is used to select two devices depending
on its state, the dummy message may disturb them.
Fixes: 5ee36c989831 ("spi: atmel_spi update chipselect handling") Cc: <stable@vger.kernel.org> Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com> Link: https://msgid.link/r/20231204154903.11607-1-louis.chauvet@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upstream commit e0205d6203c2 ("spi: atmel: Prevent false timeouts on
long transfers") has tried to mitigate the problem of getting spi
transfers canceled because they were lasting too long. On slow buses,
transfers in the MiB range can take more than one second and thus a
calculation was added to progressively increment the timeout value. In
order to not be too problematic from a user point of view (waiting dozen
of seconds or even minutes), the wait call was turned interruptible.
Turning the wait interruptible was a mistake as what we really wanted to
do was to be able to kill a transfer. Any signal interrupting our
transfer would not be suitable at all so a second attempt was made at
turning the wait killable instead.
Link: https://lore.kernel.org/linux-spi/20231127095842.389631-1-miquel.raynal@bootlin.com/
All being well, it was reported that JFFS2 was showing a splat when
interrupting a transfer. After some more debate about whether JFFS2
should be fixed and how, it was also pointed out that the whole
consistency of the filesystem in case of parallel I/O would be
compromised. Changing JFFS2 behavior would in theory be possible but
nobody has the energy and time and knowledge to do this now, so better
prevent spi transfers to be interrupted by the user.
Partially revert the blamed commit to no longer use the interruptible
nor the killable variant of wait_for_completion().
Fixes: e0205d6203c2 ("spi: atmel: Prevent false timeouts on long transfers") Cc: <stable@vger.kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: Ronald Wahl <ronald.wahl@raritan.com> Link: https://lore.kernel.org/r/20231205083102.16946-1-miquel.raynal@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intended move from wait_for_completion_*() to
wait_for_completion_interruptible_*() was to allow (very) long spi memory
transfers to be stopped upon user request instead of freezing the
machine forever as the timeout value could now be significantly bigger.
However, depending on the user logic, applications can receive many
signals for their own "internal" purpose and have nothing to do with the
requested kernel operations, hence interrupting spi transfers upon any
signal is probably not a wise choice. Instead, let's switch to
wait_for_completion_killable_*() to only catch the "important"
signals. This was likely the intended behavior anyway.
Fixes: e0205d6203c2 ("spi: atmel: Prevent false timeouts on long transfers") Cc: stable@vger.kernel.org Reported-by: Ronald Wahl <ronald.wahl@raritan.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20231127095842.389631-1-miquel.raynal@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To synchronize the timestamps with the ring buffer reservation, there are
two timestamps that are saved in the buffer meta data.
1. before_stamp
2. write_stamp
When the two are equal, the write_stamp is considered valid, as in, it may
be used to calculate the delta of the next event as the write_stamp is the
timestamp of the previous reserved event on the buffer.
This is done by the following:
/*A*/ w = current position on the ring buffer
before = before_stamp
after = write_stamp
ts = read current timestamp
if (before != after) {
write_stamp is not valid, force adding an absolute
timestamp.
}
/*B*/ before_stamp = ts
/*C*/ write = local_add_return(event length, position on ring buffer)
if (w == write - event length) {
/* Nothing interrupted between A and C */
/*E*/ write_stamp = ts;
delta = ts - after
/*
* If nothing interrupted again,
* before_stamp == write_stamp and write_stamp
* can be used to calculate the delta for
* events that come in after this one.
*/
} else {
/*
* The slow path!
* Was interrupted between A and C.
*/
This is the place that there's a bug. We currently have:
after = write_stamp
ts = read current timestamp
/*F*/ if (write == current position on the ring buffer &&
after < ts && cmpxchg(write_stamp, after, ts)) {
delta = ts - after;
} else {
delta = 0;
}
The assumption is that if the current position on the ring buffer hasn't
moved between C and F, then it also was not interrupted, and that the last
event written has a timestamp that matches the write_stamp. That is the
write_stamp is valid.
But this may not be the case:
If a task context event was interrupted by softirq between B and C.
And the softirq wrote an event that got interrupted by a hard irq between
C and E.
and the hard irq wrote an event (does not need to be interrupted)
We have:
/*B*/ before_stamp = ts of normal context
---> interrupted by softirq
/*B*/ before_stamp = ts of softirq context
---> interrupted by hardirq
/*B*/ before_stamp = ts of hard irq context
/*E*/ write_stamp = ts of hard irq context
/* matches and write_stamp valid */
<----
/*E*/ write_stamp = ts of softirq context
/* No longer matches before_stamp, write_stamp is not valid! */
<---
w != write - length, go to slow path
// Right now the order of events in the ring buffer is:
//
// |-- softirq event --|-- hard irq event --|-- normal context event --|
//
after = write_stamp (this is the ts of softirq)
ts = read current timestamp
if (write == current position on the ring buffer [true] &&
after < ts [true] && cmpxchg(write_stamp, after, ts) [true]) {
delta = ts - after [Wrong!]
The delta is to be between the hard irq event and the normal context
event, but the above logic made the delta between the softirq event and
the normal context event, where the hard irq event is between the two. This
will shift all the remaining event timestamps on the sub-buffer
incorrectly.
The write_stamp is only valid if it matches the before_stamp. The cmpxchg
does nothing to help this.
Instead, the following logic can be done to fix this:
before = before_stamp
ts = read current timestamp
before_stamp = ts
after = write_stamp
if (write == current position on the ring buffer &&
after == before && after < ts) {
delta = ts - after
} else {
delta = 0;
}
The above will only use the write_stamp if it still matches before_stamp
and was tested to not have changed since C.
As a bonus, with this logic we do not need any 64-bit cmpxchg() at all!
This means the 32-bit rb_time_t workaround can finally be removed. But
that's for a later time.
When filtering is enabled, a temporary buffer is created to place the
content of the trace event output so that the filter logic can decide
from the trace event output if the trace event should be filtered out or
not. If it is to be filtered out, the content in the temporary buffer is
simply discarded, otherwise it is written into the trace buffer.
But if an interrupt were to come in while a previous event was using that
temporary buffer, the event written by the interrupt would actually go
into the ring buffer itself to prevent corrupting the data on the
temporary buffer. If the event is to be filtered out, the event in the
ring buffer is discarded, or if it fails to discard because another event
were to have already come in, it is turned into padding.
The update to the write_stamp in the rb_try_to_discard() happens after a
fix was made to force the next event after the discard to use an absolute
timestamp by setting the before_stamp to zero so it does not match the
write_stamp (which causes an event to use the absolute timestamp).
But there's an effort in rb_try_to_discard() to put back the write_stamp
to what it was before the event was added. But this is useless and
wasteful because nothing is going to be using that write_stamp for
calculations as it still will not match the before_stamp.
Remove this useless update, and in doing so, we remove another
cmpxchg64()!
Also update the comments to reflect this change as well as remove some
extra white space in another comment.
Link: https://lore.kernel.org/linux-trace-kernel/20231215081810.1f4f38fe@rorschach.local.home Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Vincent Donnefort <vdonnefort@google.com> Fixes: b2dd797543cf ("ring-buffer: Force absolute timestamp on discard of event") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The following race can cause rb_time_read() to observe a corrupted time
stamp:
rb_time_cmpxchg()
[...]
if (!rb_time_read_cmpxchg(&t->msb, msb, msb2))
return false;
if (!rb_time_read_cmpxchg(&t->top, top, top2))
return false;
<interrupted before updating bottom>
__rb_time_read()
[...]
do {
c = local_read(&t->cnt);
top = local_read(&t->top);
bottom = local_read(&t->bottom);
msb = local_read(&t->msb);
} while (c != local_read(&t->cnt));
*cnt = rb_time_cnt(top);
/* If top and msb counts don't match, this interrupted a write */
if (*cnt != rb_time_cnt(msb))
return false;
^ this check fails to catch that "bottom" is still not updated.
So the old "bottom" value is returned, which is wrong.
Fix this by checking that all three of msb, top, and bottom 2-bit cnt
values match.
The reason to favor checking all three fields over requiring a specific
update order for both rb_time_set() and rb_time_cmpxchg() is because
checking all three fields is more robust to handle partial failures of
rb_time_cmpxchg() when interrupted by nested rb_time_set().
An out of bounds read can occur within the tracepoint 9p_protocol_dump. In
the fast assign, there is a memcpy that uses a constant size of 32 (macro
named P9_PROTO_DUMP_SZ). When the copy is invoked, the source buffer is not
guaranteed match this size. It was found that in some cases the source
buffer size is less than 32, resulting in a read that overruns.
The size of the source buffer seems to be known at the time of the
tracepoint being invoked. The allocations happen within p9_fcall_init(),
where the capacity field is set to the allocated size of the payload
buffer. This patch tries to fix the overrun by changing the fixed array to
a dynamically sized array and using the minimum of the capacity value or
P9_PROTO_DUMP_SZ as its length. The trace log statement is adjusted to
account for this. Note that the trace log no longer splits the payload on
the first 16 bytes. The full payload is now logged to a single line.
To repro the orignal problem, operations to a plan 9 managed resource can
be used. The simplest approach might just be mounting a shared filesystem
(between host and guest vm) using the plan 9 protocol while the tracepoint
is enabled.
mount -t 9p -o trans=virtio <mount_tag> <mount_path>
The bpftrace program below can be used to show the out of bounds read.
Note that a recent version of bpftrace is needed for the raw tracepoint
support. The script was tested using v0.19.0.
The pipe DMC seems to be making a mess of things in ADL. Various weird
symptoms have been observed such as missing vblank irqs, typicalle
happening when using multiple displays.
Keep all pipe DMC event handlers disabled until needed (which is never
atm). This is also what Windows does on ADL+.
We can also drop DG2 from disable_all_flip_queue_events() since
on DG2 the pipe DMC is the one that handles the flip queue events.
A small CIFS buffer (448 bytes) isn't big enough to hold
SMB2_QUERY_INFO request along with user's input data from
CIFS_QUERY_INFO ioctl. That is, if the user passed an input buffer >
344 bytes, the client will memcpy() off the end of @req->Buffer in
SMB2_query_info_init() thus causing the following KASAN splat:
BUG: KASAN: slab-out-of-bounds in SMB2_query_info_init+0x242/0x250 [cifs]
Write of size 1023 at addr ffff88801308c5a8 by task a.out/1240
Fix this by increasing size of SMB2_QUERY_INFO request buffers and
validating input length to prevent other callers from overflowing @req
in SMB2_query_info_init() as well.
Fixes: f5b05d622a3e ("cifs: add IOCTL for QUERY_INFO passthrough to userspace") Cc: stable@vger.kernel.org Reported-by: Robert Morris <rtm@csail.mit.edu> Signed-off-by: Paulo Alcantara <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Validate SMB message with ->check_message() before calling
->calc_smb_size().
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com> Cc: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Validate next header's offset in ->next_header() so that it isn't
smaller than MID_HEADER_SIZE(server) and then standard_receive3() or
->receive() ends up writing off the end of the buffer because
'pdu_length - MID_HEADER_SIZE(server)' wraps up to a huge length:
BUG: KASAN: slab-out-of-bounds in _copy_to_iter+0x4fc/0x840
Write of size 701 at addr ffff88800caf407f by task cifsd/1090
If write_ports_addfd or write_ports_addxprt fail, they call nfsd_put()
without calling nfsd_last_thread(). This leaves nn->nfsd_serv pointing
to a structure that has been freed.
So remove 'static' from nfsd_last_thread() and call it when the
nfsd_serv is about to be destroyed.
Fixes: ec52361df99b ("SUNRPC: stop using ->sv_nrthreads as a refcount") Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver should continue get the timestamp if STMMAC_FLAG_EXT_SNAPSHOT_EN
flag is set.
Fixes: aa5513f5d95f ("net: stmmac: replace the ext_snapshot_en field with a flag") Cc: <stable@vger.kernel.org> # 6.6 Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com> Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC seems to incorrectly fail to evaluate skb_ext_total_length() at
compile time under certain conditions.
The issue even occurs if all values in skb_ext_type_len[] are "0",
ruling out the possibility of an actual overflow.
As the patch has been in mainline since v6.6 without triggering the
problem it seems to be a very uncommon occurrence.
As the issue only occurs when -fno-tree-loop-im is specified as part of
CFLAGS_GCOV, disable the BUILD_BUG_ON() only when building with coverage
reporting enabled.
There is a bug in the ks8851 Ethernet driver that more data is written
to the hardware TX buffer than actually available. This is caused by
wrong accounting of the free TX buffer space.
The driver maintains a tx_space variable that represents the TX buffer
space that is deemed to be free. The ks8851_start_xmit_spi() function
adds an SKB to a queue if tx_space is large enough and reduces tx_space
by the amount of buffer space it will later need in the TX buffer and
then schedules a work item. If there is not enough space then the TX
queue is stopped.
The worker function ks8851_tx_work() dequeues all the SKBs and writes
the data into the hardware TX buffer. The last packet will trigger an
interrupt after it was send. Here it is assumed that all data fits into
the TX buffer.
In the interrupt routine (which runs asynchronously because it is a
threaded interrupt) tx_space is updated with the current value from the
hardware. Also the TX queue is woken up again.
Now it could happen that after data was sent to the hardware and before
handling the TX interrupt new data is queued in ks8851_start_xmit_spi()
when the TX buffer space had still some space left. When the interrupt
is actually handled tx_space is updated from the hardware but now we
already have new SKBs queued that have not been written to the hardware
TX buffer yet. Since tx_space has been overwritten by the value from the
hardware the space is not accounted for.
Now we have more data queued then buffer space available in the hardware
and ks8851_tx_work() will potentially overrun the hardware TX buffer. In
many cases it will still work because often the buffer is written out
fast enough so that no overrun occurs but for example if the peer
throttles us via flow control then an overrun may happen.
This can be fixed in different ways. The most simple way would be to set
tx_space to 0 before writing data to the hardware TX buffer preventing
the queuing of more SKBs until the TX interrupt has been handled. I have
chosen a slightly more efficient (and still rather simple) way and
track the amount of data that is already queued and not yet written to
the hardware. When new SKBs are to be queued the already queued amount
of data is honoured when checking free TX buffer space.
I tested this with a setup of two linked KS8851 running iperf3 between
the two in bidirectional mode. Before the fix I got a stall after some
minutes. With the fix I saw now issues anymore after hours.
Fixes: 3ba81f3ece3c ("net: Micrel KS8851 SPI network driver") Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Ben Dooks <ben.dooks@codethink.co.uk> Cc: Tristram Ha <Tristram.Ha@microchip.com> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org # 5.10+ Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20231214181112.76052-1-rwahl@gmx.de Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the undefined usage of the GPIO consumer API after retrieving the
GPIO description with GPIO_ASIS. The API documentation mentions that
GPIO_ASIS won't set a GPIO direction and requires the user to set a
direction before using the GPIO.
This can be confirmed on i.MX6 hardware, where rfkill-gpio is no longer
able to enabled/disable a device, presumably because the GPIO controller
was never configured for the output direction.
Fixes: b2f750c3a80b ("net: rfkill: gpio: prevent value glitch during probe") Cc: stable@vger.kernel.org Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de> Link: https://msgid.link/20231207075835.3091694-1-r.czerwinski@pengutronix.de Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If some of p9pdu_readf() calls inside case 'T' in p9pdu_vreadf() fails,
the error path is not handled properly. *wnames or members of *wnames
array may be left uninitialized and invalidly freed.
Initialize *wnames to NULL in beginning of case 'T'. Initialize the first
*wnames array element to NULL and nullify the failing *wnames element so
that the error path freeing loop stops on the first NULL element and
doesn't proceed further.
Found by Linux Verification Center (linuxtesting.org).
Fixes: ace51c4dd2f9 ("9p: add new protocol support code") Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Message-ID: <20231206200913.16135-1-pchelkin@ispras.ru> Cc: stable@vger.kernel.org Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: Christian Schoenebeck <linux_oss@crudebyte.com> Signed-off-by: Dominique Martinet <asmadeus@codewreck.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This add a mapping for the airplane mode button on the TUXEDO Pulse Gen3.
While it is physically a key it behaves more like a switch, sending a key
down on first press and a key up on 2nd press. Therefor the switch event
is used here. Besides this behaviour it uses the HID usage-id 0xc6
(Wireless Radio Button) and not 0xc8 (Wireless Radio Slider Switch), but
since neither 0xc6 nor 0xc8 are currently implemented at all in
soc_button_array this not to standard behaviour is not put behind a quirk
for the moment.
When the device is disconnected we get the following messages showing
failed operations:
Nov 28 20:22:11 localhost kernel: usb 2-3: USB disconnect, device number 2
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: unregister 'ax88179_178a' usb-0000:02:00.0-3, ASIX AX88179 USB 3.0 Gigabit Ethernet
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to read reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0001: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
The reason is that although the device is detached, normal stop and
unbind operations are commanded from the driver. These operations are
not necessary in this situation, so avoid these logs when the device is
detached if the result of the operation is -ENODEV and if the new flag
informing about the disconnecting status is enabled.
cc: <stable@vger.kernel.org> Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver") Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20231207175007.263907-1-jtornosm@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here "temp" is the number of characters that we have written and "size"
is the size of the buffer. The intent was clearly to say that if we have
written to the end of the buffer then stop.
However, for that to work the comparison should have been done on the
original "size" value instead of the "size -= temp" value. Not only
will that not trigger when we want to, but there is a small chance that
it will trigger incorrectly before we want it to and we break from the
loop slightly earlier than intended.
This code was recently changed from using snprintf() to scnprintf(). With
snprintf() we likely would have continued looping and passed a negative
size parameter to snprintf(). This would have triggered an annoying
WARN(). Now that we have converted to scnprintf() "size" will never
drop below 1 and there is no real need for this test. We could change
the condition to "if (temp <= 1) goto done;" but just deleting the test
is cleanest.
Fixes: 7d50195f6c50 ("usb: host: Faraday fotg210-hcd driver") Cc: stable <stable@kernel.org> Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/ZXmwIwHe35wGfgzu@suswa Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the recently added connector sanity check which was off by one and
prevented orientation notifications from being handled correctly for the
second port when using GPIOs to determine orientation.
Fixes: c6165ed2f425 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events") Cc: stable <stable@kernel.org> Cc: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20231208123603.29957-1-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we are slave role and receives l2cap conn req when encryption has
started, we should check the enc key size to avoid KNOB attack or BLUFFS
attack.
From SIG recommendation, implementations are advised to reject
service-level connections on an encrypted baseband link with key
strengths below 7 octets.
A simple and clear way to achieve this is to place the enc key size
check in hci_cc_read_enc_key_size()
The btmon log below shows the case that lacks enc key size check.
> ACL Data RX: Handle 1 flags 0x02 dlen 12
L2CAP: Connection Request (0x02) ident 3 len 4
PSM: 25 (0x0019)
Source CID: 64
< ACL Data TX: Handle 1 flags 0x00 dlen 16
L2CAP: Connection Response (0x03) ident 3 len 8
Destination CID: 64
Source CID: 64
Result: Connection pending (0x0001)
Status: Authorization pending (0x0002)
> HCI Event: Number of Completed Packets (0x13) plen 5
Num handles: 1
Handle: 1 Address: BB:22:33:44:55:99 (OUI BB-22-33)
Count: 1
#35: len 16 (25 Kb/s)
Latency: 5 msec (2-7 msec ~4 msec)
< ACL Data TX: Handle 1 flags 0x00 dlen 16
L2CAP: Connection Response (0x03) ident 3 len 8
Destination CID: 64
Source CID: 64
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
Cc: stable@vger.kernel.org Signed-off-by: Alex Lu <alex_lu@realsil.com.cn> Signed-off-by: Max Chou <max.chou@realtek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If two Bluetooth devices both support BR/EDR and BLE, and also
support Secure Connections, then they only need to pair once.
The LTK generated during the LE pairing process may be converted
into a BR/EDR link key for BR/EDR transport, and conversely, a
link key generated during the BR/EDR SSP pairing process can be
converted into an LTK for LE transport. Hence, the link type of
the link key and LTK is not fixed, they can be either an LE LINK
or an ACL LINK.
Currently, in the mgmt_new_irk/ltk/crsk/link_key functions, the
link type is fixed, which could lead to incorrect address types
being reported to the application layer. Therefore, it is necessary
to add link_type/addr_type to the smp_irk/ltk/crsk and link_key,
to ensure the generation of the correct address type.
SMP over BREDR:
Before Fix:
> ACL Data RX: Handle 11 flags 0x02 dlen 12
BR/EDR SMP: Identity Address Information (0x09) len 7
Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
Random address: 00:00:00:00:00:00 (Non-Resolvable)
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated key from P-256 (0x03)
After Fix:
> ACL Data RX: Handle 11 flags 0x02 dlen 12
BR/EDR SMP: Identity Address Information (0x09) len 7
Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
Random address: 00:00:00:00:00:00 (Non-Resolvable)
BR/EDR Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
BR/EDR Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated key from P-256 (0x03)
SMP over LE:
Before Fix:
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
Random address: 5F:5C:07:37:47:D5 (Resolvable)
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated key from P-256 (0x03)
@ MGMT Event: New Link Key (0x0009) plen 26
BR/EDR Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated Combination key from P-256 (0x08)
After Fix:
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
Random address: 5E:03:1C:00:38:21 (Resolvable)
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated key from P-256 (0x03)
@ MGMT Event: New Link Key (0x0009) plen 26
Store hint: Yes (0x01)
LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
Key type: Authenticated Combination key from P-256 (0x08)
Cc: stable@vger.kernel.org Signed-off-by: Xiao Yao <xiaoyao@rock-chips.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
L2CAP/COS/CED/BI-02-C PTS test send a malformed L2CAP signaling packet
with 2 commands in it (a connection request and an unknown command) and
expect to get a connection response packet and a command reject packet.
The second is currently not sent.
Cc: stable@vger.kernel.org Signed-off-by: Frédéric Danis <frederic.danis@collabora.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This can cause a race with bt_sock_ioctl() because
bt_sock_recvmsg() gets the skb from sk->sk_receive_queue
and then frees it without holding lock_sock.
A use-after-free for a skb occurs with the following flow.
```
bt_sock_recvmsg() -> skb_recv_datagram() -> skb_free_datagram()
bt_sock_ioctl() -> skb_peek()
```
Add lock_sock to bt_sock_recvmsg() to fix this issue.
Cc: stable@vger.kernel.org Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Hyunwoo Kim <v4bel@theori.io> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before setting HCI_INQUIRY bit check if HCI_OP_INQUIRY was really sent
otherwise the controller maybe be generating invalid events or, more
likely, it is a result of fuzzing tools attempting to test the right
behavior of the stack when unexpected events are generated.
Cc: stable@vger.kernel.org Link: https://bugzilla.kernel.org/show_bug.cgi?id=218151 Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, cur_prog/cur_conf remains at the default value (-1), while
program 0 has been loaded into the amplifiers.
In the playback hook, tasdevice_tuning_switch tries to restore the
cur_prog/cur_conf. In the runtime_resume/system_resume,
tasdevice_prmg_load tries to load the cur_prog as well.
Set cur_prog and cur_conf to 0 if available in the firmware.
The file for the new certificate (Chen-Yu Tsai's) didn't
end with a comma, so depending on the file order in the
build rule, we'd end up with invalid C when concatenating
the (now two) certificates. Fix that.
Cc: stable@vger.kernel.org Reported-by: Biju Das <biju.das.jz@bp.renesas.com> Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Fixes: fb768d3b13ff ("wifi: cfg80211: Add my certificate") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As announced [1][2], I have taken over maintainership of the
wireless-regdb project.
Add my certificate so that newer releases are valid to the kernel.
Seth's certificate should be kept around for awhile, at least until
a few new releases by me happen.
This should also be applied to stable trees so that stable kernels
can utilize newly released database binaries.
If WED rx is enabled, rx buffers are added to a buffer pool that can be
filled from multiple page pools. Because buffers freed from rx poll are
not guaranteed to belong to the processed queue's page pool, lockless
caching must not be used in this case.
Cc: stable@vger.kernel.org Fixes: 2f5c3c77fc9b ("wifi: mt76: switch to page_pool allocator") Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20231208075004.69843-1-nbd@nbd.name Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This flash drive reports write protect during the first mode sense.
In the past this was not an issue as the kernel called revalidate twice,
thus asking the device for its write protect status twice, with write
protect being disabled in the second mode sense.
However, since commit 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") that is no longer the case, thus the
device shows up read only.
[490891.289495] sd 12:0:0:0: [sdl] Write Protect is on
[490891.289497] sd 12:0:0:0: [sdl] Mode Sense: 2b 00 80 08
This does not appear to be a timing issue, as enabling the usbcore quirk
USB_QUIRK_DELAY_INIT has no effect on write protect.
Fixes: 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice") Cc: stable <stable@kernel.org> Signed-off-by: Tasos Sahanidis <tasos@tasossah.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Link: https://lore.kernel.org/r/20231207134441.298131-1-tasos@tasossah.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With subtle timings changes, we can now sometimes get an external abort on
non-linefetch error booting am3 devices at sysc_reset(). This is because
of a missing reset delay needed for the usb target module.
Looks like we never enabled the delay earlier for am3, although a similar
issue was seen earlier with a similar usb setup for dm814x as described in
commit ebf244148092 ("ARM: OMAP2+: Use srst_udelay for USB on dm814x").
Cc: stable@vger.kernel.org Fixes: 0782e8572ce4 ("ARM: dts: Probe am335x musb with ti-sysc") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Increase the quirk delay from 2 seconds to 4 seconds. This reflects a
change in the Windows driver in which the delay was increased to about
3.7 seconds. The larger delay fixes an issue where the device fails to
work unless it was powered up early during boot.
Also clarify in the quirk comment that the quirk is only applied to
older devices (USB ID 07fd:0008).
Commit ee708e6baacd ("iio: buffer: introduce support for attaching more
IIO buffers") introduced support for multiple buffers per indio_dev but
left indio_dev->buffer for a few legacy use cases.
In the case of the triggered buffer, iio_triggered_buffer_cleanup()
still assumes that indio_dev->buffer points to the buffer allocated by
iio_triggered_buffer_setup_ext(). However, since
iio_triggered_buffer_setup_ext() now calls iio_device_attach_buffer()
to attach the buffer, indio_dev->buffer will only point to the buffer
allocated by iio_device_attach_buffer() if it the first buffer attached.
This adds a check to make sure that no other buffer has been attached
yet to ensure that indio_dev->buffer will be assigned when
iio_device_attach_buffer() is called.
As per discussion in the review thread, we may want to deal with multiple
triggers per device, but this is a fix for the issue in the meantime and
any such support would be unlikely to be suitable for a backport.
Fixes: ee708e6baacd ("iio: buffer: introduce support for attaching more IIO buffers") Signed-off-by: David Lechner <dlechner@baylibre.com> Acked-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20231031210521.1661552-1-dlechner@baylibre.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current offset has the scale already applied to it. The ABI
documentation defines the offset parameter as "offset to be added
to <type>[Y]_raw prior to scaling by <type>[Y]_scale in order to
obtain value in the <type> units as specified in <type>[Y]_raw
documentation"
The right value is obtained at 0 degrees Celsius by the formula provided
in the datasheet:
T = Tsens_t0 + (Tadc_t - Tadc_t0) / Tadc_res
where:
T = 0 degrees Celsius
Tsens_t0 (reference temperature) = 25 degrees Celsius
Tadc_t0 (16-bit format for Tsens_t0) = 17508
Tadc_res = 60.1 LSB/degree Celsius
The resulting offset is 16005.5, which has been truncated to 16005 to
provide an integer value with a precision loss smaller than the 1-LSB
measurement precision.
Fix the offset to apply its value prior to scaling.
Fix wrong handling of a DMA request where the probing only failed
if -EPROPE_DEFER was returned. Instead, let us fail if a non -ENODEV
value is returned. This makes DMAs explicitly optional. Even if the
DMA request is unsuccessfully, the ADC can still work properly.
We do also handle the defer probe case by making use of dev_err_probe().
This prevents the warning message "SPI driver has no spi_device_id for..."
when registering the driver. More importantly, it makes sure that
module autoloading works as spi relies on spi: modaliases and not of.
While at it, move the of_device_id table to it's natural place.
Fixes: fff7352bf7a3c ("iio: imu: Add support for adis16475") Signed-off-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20231102125258.3284830-1-nuno.sa@analog.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HTU21 offers 4 sampling frequencies: 20, 40, 70 and 120, which are
associated to an index that is used to select the right measurement
resolution and its corresponding measurement time. The current
implementation selects the measurement resolution and the temperature
measurement time properly, but it does not select the right humidity
measurement time in all cases.
In summary, the 40 and 70 humidity measurement times are swapped.
The reason for that is probably the unusual coding for the measurement
resolution. According to the datasheet, the bits [7,0] of the "user
register" are used as follows to select the bit resolution:
--------------------------------------------------
| Bit 7 | Bit 0 | RH | Temp | Trh (us) | Tt (us) |
--------------------------------------------------
| 0 | 0 | 12 | 14 | 16000 | 50000 |
--------------------------------------------------
| 0 | 1 | 8 | 12 | 3000 | 13000 |
--------------------------------------------------
| 1 | 0 | 10 | 13 | 5000 | 25000 |
--------------------------------------------------
| 1 | 1 | 11 | 11 | 8000 | 7000 |
--------------------------------------------------
*This table is available in the official datasheet, page 13/21. I have
just appended the times provided in the humidity/temperature tables,
pages 3/21, 5/21. Note that always a pair of resolutions is selected.
The sampling frequencies [20, 40, 70, 120] are assigned to a linear
index [0..3] which is then coded as follows [1]:
That is done that way because the temperature measurements are being
used as the reference for the sampling frequency (the frequencies and
the temperature measurement times are correlated), so increasing the
index always reduces the temperature measurement time and its
resolution. Therefore, the temperature measurement time array is as
simple as [50000, 25000, 13000, 7000]
On the other hand, the humidity resolution cannot follow the same
pattern because of the way it is coded in the "user register", where
both resolutions are selected at the same time. The humidity measurement
time array is the following: [16000, 3000, 5000, 8000], which defines
the following assignments:
The times have been ordered as if idx = 1 -> [0,1] and idx = 2 -> [1,0],
which is not the case for the reason explained above.
So a simple modification is required to obtain the right humidity
measurement time array, swapping the values in the positions 1 and 2.
The right table should be the following: [16000, 5000, 3000, 8000]
Fix the humidity measurement time array with the right idex/value
coding.
[1] The actual code that makes this coding and assigns it to the current
value of the "user register" is the following:
config_reg &= 0x7E;
config_reg |= ((i & 1) << 7) + ((i & 2) >> 1);
Fixes: d574a87cc311 ("Add meas-spec sensors common part") Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://lore.kernel.org/r/20231026-topic-htu21_conversion_time-v1-1-bd257dc44209@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the spec, this ADC totally support 8 channels.
i.MX93 contain this ADC with 4 channels connected to pins in
the package. i.MX95 contain this ADC with 8 channels connected
to pins in the package.
When accessing sq_tail_slot without protection from sq_lock, a race
condition can cause multiple SQEs to be copied to duplicate SQE slots. This
can lead to multiple stability issues. Fix this by moving the *dest
initialization in ufshcd_send_command() back under protection from the
sq_lock.
Fixes: 3c85f087faec ("scsi: ufs: mcq: Use pointer arithmetic in ufshcd_send_command()") Signed-off-by: Can Guo <quic_cang@quicinc.com> Link: https://lore.kernel.org/r/1702913550-20631-1-git-send-email-quic_cang@quicinc.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 031312dbc695 ("scsi: ufs: ufs-qcom: Remove unnecessary goto
statements") the error handling was accidentally changed, resulting in the
error of ufs_qcom_clk_scale_*() calls not being returned.
skb_share_check() already drops the reference to the skb when returning
NULL. Using kfree_skb() in the error handling path leads to an skb double
free.
Fix this by removing the variable tmp_skb, and return directly when
skb_share_check() returns NULL.
Fixes: 01a4cc4d0cd6 ("bnx2fc: do not add shared skbs to the fcoe_rx_list") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20221114110626.526643-1-weiyongjun@huaweicloud.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to Amlogic custom kernels ADC of axg SoC family has
vref_select and requires this setting to work nominally and thus
needs a separate config.
Fixes: 90c6241860bf ("iio: adc: meson: init voltage control bits") Signed-off-by: George Stark <gnstark@salutedevices.com> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://lore.kernel.org/r/20231127235558.71995-1-gnstark@salutedevices.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Check the return value of i2c_add_adapter. Static analysis revealed that
the function did not properly handle potential failures of
i2c_add_adapter, which could lead to partial initialization of the I2C
adapter and unstable operation.
Signed-off-by: Haoran Liu <liuhaoran14@163.com> Link: https://lore.kernel.org/r/20231203164653.38983-1-liuhaoran14@163.com Fixes: d7535ffa427b ("Input: driver for microcontroller keys on the iPaq h3xxx") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, if provider->xlate() or provider->xlate_extended()
"successfully" return a NULL node, then of_icc_get_from_provider() won't
consider that an error and will successfully return the NULL node. This
bypasses error handling in of_icc_get_by_index() and leads to NULL
dereferences in path_find().
This could be avoided by ensuring provider callbacks always return an
error for NULL nodes, but it's better to explicitly protect against this
in the common framework.
Fixes: 87e3031b6fbd ("interconnect: Allow endpoints translation via DT") Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com> Link: https://lore.kernel.org/r/20231025145829.11603-1-quic_mdtipton@quicinc.com Signed-off-by: Georgi Djakov <djakov@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
the nvme_handle_cqe() interrupt handler calls nvme_complete_async_event()
but the latter may call nvme_auth_stop() which is a blocking function.
Sleeping functions can't be called in interrupt context
While the GPIO cdev gpio_ioctl() call is in progress, the kernel can
call gpiochip_remove() which will set gdev->chip to NULL, after which
any subsequent access will cause a crash.
gpio_ioctl() was overlooked by the previous fix to protect syscalls
(bdbbae241a04), so add protection for that.
Fixes: bdbbae241a04 ("gpiolib: protect the GPIO device against being dropped while in use by user-space") Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines") Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL") Fixes: aad955842d1c ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL") Signed-off-by: Kent Gibson <warthog618@gmail.com> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
stack backtrace:
CPU: 0 PID: 92 Comm: sh Not tainted 6.7.0-rc5-wt+ #532
Hardware name: Atmel SAMA5
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x48
dump_stack_lvl from __lock_acquire+0x19ec/0x3a0c
__lock_acquire from lock_acquire.part.0+0x124/0x2d0
lock_acquire.part.0 from _raw_spin_lock_irqsave+0x5c/0x78
_raw_spin_lock_irqsave from __irq_get_desc_lock+0xe8/0x100
__irq_get_desc_lock from irq_set_irq_wake+0xa8/0x204
irq_set_irq_wake from atmel_gpio_irq_set_wake+0x58/0xb4
atmel_gpio_irq_set_wake from irq_set_irq_wake+0x100/0x204
irq_set_irq_wake from gpio_keys_suspend+0xec/0x2b8
gpio_keys_suspend from dpm_run_callback+0xe4/0x248
dpm_run_callback from __device_suspend+0x234/0x91c
__device_suspend from dpm_suspend+0x224/0x43c
dpm_suspend from dpm_suspend_start+0x9c/0xa8
dpm_suspend_start from suspend_devices_and_enter+0x1e0/0xa84
suspend_devices_and_enter from pm_suspend+0x460/0x4e8
pm_suspend from state_store+0x78/0xe4
state_store from kernfs_fop_write_iter+0x1a0/0x284
kernfs_fop_write_iter from vfs_write+0x38c/0x6f4
vfs_write from ksys_write+0xd8/0x178
ksys_write from ret_fast_syscall+0x0/0x1c
Exception stack(0xc52b3fa8 to 0xc52b3ff0)
3fa0: 00000004005a0ae800000001005a0ae80000000400000001
3fc0: 00000004005a0ae8000000010000000400000004b6c616c0000000200059d190
3fe0: 00000004b6c61678aec5a041aebf1a26
This warning is raised because pinctrl-at91-pio4 uses chained IRQ. Whenever
a wake up source configures an IRQ through irq_set_irq_wake, it will
lock the corresponding IRQ desc, and then call irq_set_irq_wake on "parent"
IRQ which will do the same on its own IRQ desc, but since those two locks
share the same class, lockdep reports this as an issue.
Fix lockdep false positive by setting a different class for parent and
children IRQ
Xen only supports modern CPUs even when running a 32-bit kernel, and it now
requires a kernel built for a 64 byte (or larger) cache line:
In file included from <command-line>:
In function 'xen_vcpu_setup',
inlined from 'xen_vcpu_setup_restore' at arch/x86/xen/enlighten.c:111:3,
inlined from 'xen_vcpu_restore' at arch/x86/xen/enlighten.c:141:3:
include/linux/compiler_types.h:435:45: error: call to '__compiletime_assert_287' declared with attribute error: BUILD_BUG_ON failed: sizeof(*vcpup) > SMP_CACHE_BYTES
arch/x86/xen/enlighten.c:166:9: note: in expansion of macro 'BUILD_BUG_ON'
166 | BUILD_BUG_ON(sizeof(*vcpup) > SMP_CACHE_BYTES);
| ^~~~~~~~~~~~
Enforce the dependency with a whitelist of CPU configurations. In normal
distro kernels, CONFIG_X86_GENERIC is enabled, and this works fine. When this
is not set, still allow Xen to be built on kernels that target a 64-bit
capable CPU.
Some masters may drive the transfers with low enough latency between
the nak/stop phase of the current command and the start/address phase
of the following command that the interrupts are coalesced by the
time we process them.
Handle the stop conditions before processing SLAVE_MATCH to fix the
complaints that sometimes occur below.
"aspeed-i2c-bus 1e78a040.i2c-bus: irq handled != irq. Expected
0x00000086, but was 0x00000084"
Fixes: f9eb91350bb2 ("i2c: aspeed: added slave support for Aspeed I2C driver") Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au> Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Idle bo's PTE needs to be re-created when resetting VM state machine.
Set idle bo's vm_bo as moved to mark it as invalid.
Fixes: 55bf196f60df ("drm/amdgpu: reset VM when an error is detected") Signed-off-by: ZhenGuo Yin <zhenguo.yin@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When flag mclk_with_tere and mclk_direction_output enabled,
The SAI transmitter or receiver will be enabled in very early
stage, that if FSL_SAI_xMR is set by previous case,
for example previous case is one channel, current case is
two channels, then current case started with wrong xMR in
the beginning, then channel swap happen.
The patch is to clear xMR in hw_free() to avoid such
channel swap issue.
Fixes: 3e4a82612998 ("ASoC: fsl_sai: MCLK bind with TX/RX enable bit") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com> Link: https://msgid.link/r/1702953057-4499-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an afs_volume struct is put, its refcount is reduced to 0 before
the cell->volume_lock is taken and the volume removed from the
cell->volumes tree.
Unfortunately, this means that the lookup code can race and see a volume
with a zero ref in the tree, resulting in a use-after-free:
(1) When putting, use a flag to indicate if the volume has been removed
from the tree and skip the rb_erase if it has.
(2) When looking up, use a conditional ref increment and if it fails
because the refcount is 0, replace the node in the tree and set the
removal flag.
Fixes: 20325960f875 ("afs: Reorganise volume and server trees to be rooted on the cell") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In afs_update_cell(), ret is the result of the DNS lookup and the errors
are to be handled by a switch - however, the value gets clobbered in
between by setting it to -ENOMEM in case afs_alloc_vlserver_list()
fails.
Fix this by moving the setting of -ENOMEM into the error handling for
OOM failure. Further, only do it if we don't have an alternative error
to return.
Found by Linux Verification Center (linuxtesting.org) with SVACE. Based
on a patch from Anastasia Belova [1].
If a key has an expiration time, then when that time passes, the key is
left around for a certain amount of time before being collected (5 mins by
default) so that EKEYEXPIRED can be returned instead of ENOKEY. This is a
problem for DNS keys because we want to redo the DNS lookup immediately at
that point.
Fix this by allowing key types to be marked such that keys of that type
don't have this extra period, but are reclaimed as soon as they expire and
turn this on for dns_resolver-type keys. To make this easier to handle,
key->expiry is changed to be permanent if TIME64_MAX rather than 0.
Furthermore, give such new-style negative DNS results a 1s default expiry
if no other expiry time is set rather than allowing it to stick around
indefinitely. This shouldn't be zero as ls will follow a failing stat call
immediately with a second with AT_SYMLINK_NOFOLLOW added.
Fixes: 1a4240f4764a ("DNS: Separate out CIFS DNS Resolver code") Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: Wang Lei <wang840925@gmail.com>
cc: Jeff Layton <jlayton@redhat.com>
cc: Steve French <smfrench@gmail.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Jarkko Sakkinen <jarkko@kernel.org>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: linux-cifs@vger.kernel.org
cc: linux-nfs@vger.kernel.org
cc: ceph-devel@vger.kernel.org
cc: keyrings@vger.kernel.org
cc: netdev@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Some drivers might misbehave if TSO packets get too big.
GVE for instance uses a 16bit field in its TX descriptor,
and will do bad things if a packet is bigger than 2^16 bytes.
Linux TCP stack honors dev->gso_max_size, but there are
other ways for too big packets to reach an ndo_start_xmit()
handler : virtio_net, af_packet, GRO...
Add a generic check in gso_features_check() and fallback
to GSO when needed.
gso_max_size was added in the blamed commit.
Fixes: 82cc1a7a5687 ("[NET]: Add per-connection option to set max TSO frame size") Signed-off-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20231219125331.4127498-1-edumazet@google.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit has some race conditions given how expires is managed on a
fib6_info in relation to gc start, adding the entry to the gc list and
setting the timer value leading to UAF. Revert the commit and try again
in a later release.
Fixes: 3dec89b14d37 ("net/ipv6: Remove expired routes with a separated list of routes") Cc: Kui-Feng Lee <thinker.li@gmail.com> Signed-off-by: David Ahern <dsahern@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20231219030243.25687-1-dsahern@kernel.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the afs dynamic root directory, the ->lookup() function does a DNS check
on the cell being asked for and if the DNS upcall reports an error it will
report an error back to userspace (typically ENOENT).
However, if a failed DNS upcall returns a new-style result, it will return
a valid result, with the status field set appropriately to indicate the
type of failure - and in that case, dns_query() doesn't return an error and
we let stat() complete with no error - which can cause confusion in
userspace as subsequent calls that trigger d_automount then fail with
ENOENT.
Fix this by checking the status result from a valid dns_query() and
returning an error if it indicates a failure.
Fixes: bbb4c4323a4d ("dns: Allow the dns resolver to retrieve a server set") Reported-by: Markus Suvanto <markus.suvanto@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=216637 Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the afs dynamic root's d_delete function to always delete unused
dentries rather than only deleting them if they're positive. With things
as they stand upstream, negative dentries stemming from failed DNS lookups
stick around preventing retries.
Fixes: 66c7e1d319a5 ("afs: Split the dynroot stuff out and give it its own ops tables") Signed-off-by: David Howells <dhowells@redhat.com> Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
WARNING: CPU: 4 PID: 4056 at net/core/dev.c:11066 unregister_netdevice_many_notify
CPU: 4 PID: 4056 Comm: ip Not tainted 6.7.0-rc4+ #15
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
RIP: 0010:unregister_netdevice_many_notify+0x9a4/0x9b0
Call Trace:
rtnl_dellink
rtnetlink_rcv_msg
netlink_rcv_skb
netlink_unicast
netlink_sendmsg
__sock_sendmsg
____sys_sendmsg
___sys_sendmsg
__sys_sendmsg
do_syscall_64
entry_SYSCALL_64_after_hwframe
It can be repoduced via:
ip netns add ns1
ip netns exec ns1 ip link add bond0 type bond mode 0
ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
ip netns exec ns1 ip link set bond_slave_1 master bond0
[1] ip netns exec ns1 ethtool -K bond0 rx-vlan-filter off
[2] ip netns exec ns1 ip link add link bond_slave_1 name bond_slave_1.0 type vlan id 0
[3] ip netns exec ns1 ip link add link bond0 name bond0.0 type vlan id 0
[4] ip netns exec ns1 ip link set bond_slave_1 nomaster
[5] ip netns exec ns1 ip link del veth2
ip netns del ns1
This is all caused by command [1] turning off the rx-vlan-filter function
of bond0. The reason is the same as commit 01f4fd270870 ("bonding: Fix
incorrect deletion of ETH_P_8021AD protocol vid from slaves"). Commands
[2] [3] add the same vid to slave and master respectively, causing
command [4] to empty slave->vlan_info. The following command [5] triggers
this problem.
To fix this problem, we should add VLAN_FILTER feature checks in
vlan_vids_add_by_dev() and vlan_vids_del_by_dev() to prevent incorrect
addition or deletion of vlan_vid information.
Fixes: 348a1443cc43 ("vlan: introduce functions to do mass addition/deletion of vids by another device") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 6624e780a577fc596788 ("ice: split ice_vsi_setup into smaller
functions") has refactored a bunch of code involved in PFR. In this
process, TC queue number adjustment for XDP was lost. Bring it back.
Lack of such adjustment causes interface to go into no-carrier after a
reset, if XDP program is attached, with the following message:
ice 0000:b1:00.0: Failed to set LAN Tx queue context, error: -22
ice 0000:b1:00.0 ens801f0np0: Failed to open VSI 0x0006 on switch 0x0001
ice 0000:b1:00.0: enable VSI failed, err -22, VSI index 0, type ICE_VSI_PF
ice 0000:b1:00.0: PF VSI rebuild failed: -22
ice 0000:b1:00.0: Rebuild failed, unload and reload driver
Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously, the ice driver had support for using a handler for bonding
netdev events to ensure that conflicting features were not allowed to be
activated at the same time. While this was still in place, additional
support was added to specifically support SRIOV and LAG together. These
both utilized the netdev event handler, but the SRIOV and LAG feature was
behind a capabilities feature check to make sure the current NVM has
support.
The exclusion part of the event handler should be removed since there are
users who have custom made solutions that depend on the non-exclusion of
features.
Wrap the creation/registration and cleanup of the event handler and
associated structs in the probe flow with a feature check so that the
only systems that support the full implementation of LAG features will
initialize support. This will leave other systems unhindered with
functionality as it existed before any LAG code was added.
Fixes: bb52f42acef6 ("ice: Add driver support for firmware changes for LAG") Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log