-/**
- * Copyright (C) 2016 - 2017 Bosch Sensortec GmbH
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions are met:
- *
- * Redistributions of source code must retain the above copyright
- * notice, this list of conditions and the following disclaimer.
- *
- * Redistributions in binary form must reproduce the above copyright
- * notice, this list of conditions and the following disclaimer in the
- * documentation and/or other materials provided with the distribution.
- *
- * Neither the name of the copyright holder nor the names of the
- * contributors may be used to endorse or promote products derived from
- * this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
- * CONTRIBUTORS "AS IS" AND ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
- * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
- * DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDER
- * OR CONTRIBUTORS BE LIABLE FOR ANY
- * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
- * OR CONSEQUENTIAL DAMAGES(INCLUDING, BUT NOT LIMITED TO,
- * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
- * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
- * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
- * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
- * ANY WAY OUT OF THE USE OF THIS
- * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE
- *
- * The information provided is believed to be accurate and reliable.
- * The copyright holder assumes no responsibility
- * for the consequences of use
- * of such information nor for any infringement of patents or
- * other rights of third parties which may result from its use.
- * No license is granted by implication or otherwise under any patent or
- * patent rights of the copyright holder.
- *
- * @file bme280.h
- * @date 13 Jul 2017
- * @version 3.3.0
- * @brief
- *
- */
-/*! @file bme280.h
- @brief Sensor driver for BME280 sensor */
-/*!
- * @defgroup BME280 SENSOR API
- * @{*/
-#ifndef BME280_H_
-#define BME280_H_
-
-/*! CPP guard */
-#ifdef __cplusplus
-extern "C" {
-#endif
-
-/* Header includes */
-#include "bme280_defs.h"
-
-/*!
- * @brief This API is the entry point.
- * It reads the chip-id and calibration data from the sensor.
- *
- * @param[in,out] dev : Structure instance of bme280_dev
- *
- * @return Result of API execution status
- * @retval zero -> Success / +ve value -> Warning / -ve value -> Error
- */
-int8_t bme280_init(struct bme280_dev *dev);
-
-/*!
- * @brief This API writes the given data to the register address
- * of the sensor.
- *
- * @param[in] reg_addr : Register address from where the data to be written.
- * @param[in] reg_data : Pointer to data buffer which is to be written
- * in the sensor.
- * @param[in] len : No of bytes of data to write..
- * @param[in] dev : Structure instance of bme280_dev.
- *
- * @return Result of API execution status
- * @retval zero -> Success / +ve value -> Warning / -ve value -> Error
- */
-int8_t bme280_set_regs(uint8_t *reg_addr, const uint8_t *reg_data, uint8_t len, const struct bme280_dev *dev);
-
-/*!
- * @brief This API reads the data from the given register address of the sensor.
- *
- * @param[in] reg_addr : Register address from where the data to be read
- * @param[out] reg_data : Pointer to data buffer to store the read data.
- * @param[in] len : No of bytes of data to be read.
- * @param[in] dev : Structure instance of bme280_dev.
- *
- * @return Result of API execution status
- * @retval zero -> Success / +ve value -> Warning / -ve value -> Error
- */
-int8_t bme280_get_regs(uint8_t reg_addr, uint8_t *reg_data, uint16_t len, const struct bme280_dev *dev);
-
-/*!
- * @brief This API sets the oversampling, filter and standby duration
- * (normal mode) settings in the sensor.
- *
- * @param[in] dev : Structure instance of bme280_dev.
- * @param[in] desired_settings : Variable used to select the settings which
- * are to be set in the sensor.
- *
- * @note : Below are the macros to be used by the user for selecting the
- * desired settings. User can do OR operation of these macros for configuring
- * multiple settings.
- *
- * Macros | Functionality
- * -----------------------|----------------------------------------------
- * BME280_OSR_PRESS_SEL | To set pressure oversampling.
- * BME280_OSR_TEMP_SEL | To set temperature oversampling.
- * BME280_OSR_HUM_SEL | To set humidity oversampling.
- * BME280_FILTER_SEL | To set filter setting.
- * BME280_STANDBY_SEL | To set standby duration setting.
- *
- * @return Result of API execution status
- * @retval zero -> Success / +ve value -> Warning / -ve value -> Error.
- */
-int8_t bme280_set_sensor_settings(uint8_t desired_settings, const struct bme280_dev *dev);
-
-/*!
- * @brief This API gets the oversampling, filter and standby duration
- * (normal mode) settings from the sensor.
- *
- * @param[in,out] dev : Structure instance of bme280_dev.
- *
- * @return Result of API execution status
- * @retval zero -> Success / +ve value -> Warning / -ve value -> Error.
- */
-int8_t bme280_get_sensor_settings(struct bme280_dev *dev);
-
-/*!
- * @brief This API sets the power mode of the sensor.
- *
- * @param[in] dev : Structure instance of bme280_dev.
- * @param[in] sensor_mode : Variable which contains the power mode to be set.
- *
- * sensor_mode | Macros
- * ---------------------|-------------------
- * 0 | BME280_SLEEP_MODE
- * 1 | BME280_FORCED_MODE
- * 3 | BME280_NORMAL_MODE
- *
- * @return Result of API execution status
- * @retval zero -> Success / +ve value -> Warning / -ve value -> Error
- */
-int8_t bme280_set_sensor_mode(uint8_t sensor_mode,
- const struct bme280_dev *dev);
-
-/*!
- * @brief This API gets the power mode of the sensor.
- *
- * @param[in] dev : Structure instance of bme280_dev.
- * @param[out] sensor_mode : Pointer variable to store the power mode.
- *
- * sensor_mode | Macros
- * ---------------------|-------------------
- * 0 | BME280_SLEEP_MODE
- * 1 | BME280_FORCED_MODE
- * 3 | BME280_NORMAL_MODE
- *
- * @return Result of API execution status
- * @retval zero -> Success / +ve value -> Warning / -ve value -> Error
- */
-int8_t bme280_get_sensor_mode(uint8_t *sensor_mode, const struct bme280_dev *dev);
-
-/*!
- * @brief This API performs the soft reset of the sensor.
- *
- * @param[in] dev : Structure instance of bme280_dev.
- *
- * @return Result of API execution status
- * @retval zero -> Success / +ve value -> Warning / -ve value -> Error.
- */
-int8_t bme280_soft_reset(const struct bme280_dev *dev);
-
-/*!
- * @brief This API reads the pressure, temperature and humidity data from the
- * sensor, compensates the data and store it in the bme280_data structure
- * instance passed by the user.
- *
- * @param[in] sensor_comp : Variable which selects which data to be read from
- * the sensor.
- *
- * sensor_comp | Macros
- * ------------|-------------------
- * 1 | BME280_PRESS
- * 2 | BME280_TEMP
- * 4 | BME280_HUM
- * 7 | BME280_ALL
- *
- * @param[out] comp_data : Structure instance of bme280_data.
- * @param[in] dev : Structure instance of bme280_dev.
- *
- * @return Result of API execution status
- * @retval zero -> Success / +ve value -> Warning / -ve value -> Error
- */
-int8_t bme280_get_sensor_data(uint8_t sensor_comp, struct bme280_data *comp_data, struct bme280_dev *dev);
-
-#ifdef __cplusplus
-}
-#endif /* End of CPP guard */
-#endif /* BME280_H_ */
-/** @}*/
+/**\r
+* Copyright (c) 2020 Bosch Sensortec GmbH. All rights reserved.\r
+*\r
+* BSD-3-Clause\r
+*\r
+* Redistribution and use in source and binary forms, with or without\r
+* modification, are permitted provided that the following conditions are met:\r
+*\r
+* 1. Redistributions of source code must retain the above copyright\r
+* notice, this list of conditions and the following disclaimer.\r
+*\r
+* 2. Redistributions in binary form must reproduce the above copyright\r
+* notice, this list of conditions and the following disclaimer in the\r
+* documentation and/or other materials provided with the distribution.\r
+*\r
+* 3. Neither the name of the copyright holder nor the names of its\r
+* contributors may be used to endorse or promote products derived from\r
+* this software without specific prior written permission.\r
+*\r
+* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS\r
+* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT\r
+* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS\r
+* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE\r
+* COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,\r
+* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES\r
+* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR\r
+* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)\r
+* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,\r
+* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING\r
+* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE\r
+* POSSIBILITY OF SUCH DAMAGE.\r
+*\r
+* @file bme280.h\r
+* @date 2020-03-28\r
+* @version v3.5.0\r
+*\r
+*/\r
+\r
+/*! @file bme280.h\r
+ * @brief Sensor driver for BME280 sensor\r
+ */\r
+\r
+/*!\r
+ * @defgroup bme280 BME280\r
+ * @brief <a href="https://www.bosch-sensortec.com/bst/products/all_products/bme280">Product Overview</a>\r
+ * and <a href="https://github.com/BoschSensortec/BME280_driver">Sensor API Source Code</a>\r
+ */\r
+\r
+#ifndef BME280_H_\r
+#define BME280_H_\r
+\r
+/*! CPP guard */\r
+#ifdef __cplusplus\r
+extern "C" {\r
+#endif\r
+\r
+/* Header includes */\r
+#include "bme280_defs.h"\r
+\r
+/**\r
+ * \ingroup bme280\r
+ * \defgroup bme280ApiInit Initialization\r
+ * @brief Initialize the sensor and device structure\r
+ */\r
+\r
+/*!\r
+ * \ingroup bme280ApiInit\r
+ * \page bme280_api_bme280_init bme280_init\r
+ * \code\r
+ * int8_t bme280_init(struct bme280_dev *dev);\r
+ * \endcode\r
+ * @details This API reads the chip-id of the sensor which is the first step to\r
+ * verify the sensor and also calibrates the sensor\r
+ * As this API is the entry point, call this API before using other APIs.\r
+ *\r
+ * @param[in,out] dev : Structure instance of bme280_dev\r
+ *\r
+ * @return Result of API execution status.\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_init(struct bme280_dev *dev);\r
+\r
+/**\r
+ * \ingroup bme280\r
+ * \defgroup bme280ApiRegister Registers\r
+ * @brief Generic API for accessing sensor registers\r
+ */\r
+\r
+/*!\r
+ * \ingroup bme280ApiRegister\r
+ * \page bme280_api_bme280_set_regs bme280_set_regs\r
+ * \code\r
+ * int8_t bme280_set_regs(const uint8_t reg_addr, const uint8_t *reg_data, uint8_t len, struct bme280_dev *dev);\r
+ * \endcode\r
+ * @details This API writes the given data to the register address of the sensor\r
+ *\r
+ * @param[in] reg_addr : Register addresses to where the data is to be written\r
+ * @param[in] reg_data : Pointer to data buffer which is to be written\r
+ * in the reg_addr of sensor.\r
+ * @param[in] len : No of bytes of data to write\r
+ * @param[in,out] dev : Structure instance of bme280_dev\r
+ *\r
+ * @return Result of API execution status.\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_set_regs(uint8_t *reg_addr, const uint8_t *reg_data, uint8_t len, struct bme280_dev *dev);\r
+\r
+/*!\r
+ * \ingroup bme280ApiRegister\r
+ * \page bme280_api_bme280_get_regs bme280_get_regs\r
+ * \code\r
+ * int8_t bme280_get_regs(uint8_t reg_addr, uint8_t *reg_data, uint8_t len, struct bme280_dev *dev);\r
+ * \endcode\r
+ * @details This API reads the data from the given register address of sensor.\r
+ *\r
+ * @param[in] reg_addr : Register address from where the data to be read\r
+ * @param[out] reg_data : Pointer to data buffer to store the read data.\r
+ * @param[in] len : No of bytes of data to be read.\r
+ * @param[in,out] dev : Structure instance of bme280_dev.\r
+ *\r
+ * @return Result of API execution status.\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_get_regs(uint8_t reg_addr, uint8_t *reg_data, uint16_t len, struct bme280_dev *dev);\r
+\r
+/**\r
+ * \ingroup bme280\r
+ * \defgroup bme280ApiSensorSettings Sensor Settings\r
+ * @brief Generic API for accessing sensor settings\r
+ */\r
+\r
+/*!\r
+ * \ingroup bme280ApiSensorSettings\r
+ * \page bme280_api_bme280_set_sensor_settings bme280_set_sensor_settings\r
+ * \code\r
+ * int8_t bme280_set_sensor_settings(uint8_t desired_settings, const struct bme280_dev *dev);\r
+ * \endcode\r
+ * @details This API sets the oversampling, filter and standby duration\r
+ * (normal mode) settings in the sensor.\r
+ *\r
+ * @param[in] dev : Structure instance of bme280_dev.\r
+ * @param[in] desired_settings : Variable used to select the settings which\r
+ * are to be set in the sensor.\r
+ *\r
+ * @note : Below are the macros to be used by the user for selecting the\r
+ * desired settings. User can do OR operation of these macros for configuring\r
+ * multiple settings.\r
+ *\r
+ * Macros | Functionality\r
+ * -----------------------|----------------------------------------------\r
+ * BME280_OSR_PRESS_SEL | To set pressure oversampling.\r
+ * BME280_OSR_TEMP_SEL | To set temperature oversampling.\r
+ * BME280_OSR_HUM_SEL | To set humidity oversampling.\r
+ * BME280_FILTER_SEL | To set filter setting.\r
+ * BME280_STANDBY_SEL | To set standby duration setting.\r
+ *\r
+ * @return Result of API execution status\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_set_sensor_settings(uint8_t desired_settings, struct bme280_dev *dev);\r
+\r
+/*!\r
+ * \ingroup bme280ApiSensorSettings\r
+ * \page bme280_api_bme280_get_sensor_settings bme280_get_sensor_settings\r
+ * \code\r
+ * int8_t bme280_get_sensor_settings(struct bme280_dev *dev);\r
+ * \endcode\r
+ * @details This API gets the oversampling, filter and standby duration\r
+ * (normal mode) settings from the sensor.\r
+ *\r
+ * @param[in,out] dev : Structure instance of bme280_dev.\r
+ *\r
+ * @return Result of API execution status\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_get_sensor_settings(struct bme280_dev *dev);\r
+\r
+/**\r
+ * \ingroup bme280\r
+ * \defgroup bme280ApiSensorMode Sensor Mode\r
+ * @brief Generic API for configuring sensor power mode\r
+ */\r
+\r
+/*!\r
+ * \ingroup bme280ApiSensorMode\r
+ * \page bme280_api_bme280_set_sensor_mode bme280_set_sensor_mode\r
+ * \code\r
+ * int8_t bme280_set_sensor_mode(uint8_t sensor_mode, const struct bme280_dev *dev);\r
+ * \endcode\r
+ * @details This API sets the power mode of the sensor.\r
+ *\r
+ * @param[in] dev : Structure instance of bme280_dev.\r
+ * @param[in] sensor_mode : Variable which contains the power mode to be set.\r
+ *\r
+ * sensor_mode | Macros\r
+ * ---------------------|-------------------\r
+ * 0 | BME280_SLEEP_MODE\r
+ * 1 | BME280_FORCED_MODE\r
+ * 3 | BME280_NORMAL_MODE\r
+ *\r
+ * @return Result of API execution status\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_set_sensor_mode(uint8_t sensor_mode, struct bme280_dev *dev);\r
+\r
+/*!\r
+ * \ingroup bme280ApiSensorMode\r
+ * \page bme280_api_bme280_get_sensor_mode bme280_get_sensor_mode\r
+ * \code\r
+ * int8_t bme280_get_sensor_mode(uint8_t *sensor_mode, const struct bme280_dev *dev);\r
+ * \endcode\r
+ * @details This API gets the power mode of the sensor.\r
+ *\r
+ * @param[in] dev : Structure instance of bme280_dev.\r
+ * @param[out] sensor_mode : Pointer variable to store the power mode.\r
+ *\r
+ * sensor_mode | Macros\r
+ * ---------------------|-------------------\r
+ * 0 | BME280_SLEEP_MODE\r
+ * 1 | BME280_FORCED_MODE\r
+ * 3 | BME280_NORMAL_MODE\r
+ *\r
+ * @return Result of API execution status\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_get_sensor_mode(uint8_t *sensor_mode, struct bme280_dev *dev);\r
+\r
+/**\r
+ * \ingroup bme280\r
+ * \defgroup bme280ApiSystem System\r
+ * @brief API that performs system-level operations\r
+ */\r
+\r
+/*!\r
+ * \ingroup bme280ApiSystem\r
+ * \page bme280_api_bme280_soft_reset bme280_soft_reset\r
+ * \code\r
+ * int8_t bme280_soft_reset(struct bme280_dev *dev);\r
+ * \endcode\r
+ * @details This API soft-resets the sensor.\r
+ *\r
+ * @param[in,out] dev : Structure instance of bme280_dev.\r
+ *\r
+ * @return Result of API execution status.\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_soft_reset(struct bme280_dev *dev);\r
+\r
+/**\r
+ * \ingroup bme280\r
+ * \defgroup bme280ApiSensorData Sensor Data\r
+ * @brief Data processing of sensor\r
+ */\r
+\r
+/*!\r
+ * \ingroup bme280ApiSensorData\r
+ * \page bme280_api_bme280_get_sensor_data bme280_get_sensor_data\r
+ * \code\r
+ * int8_t bme280_get_sensor_data(uint8_t sensor_comp, struct bme280_data *comp_data, struct bme280_dev *dev);\r
+ * \endcode\r
+ * @details This API reads the pressure, temperature and humidity data from the\r
+ * sensor, compensates the data and store it in the bme280_data structure\r
+ * instance passed by the user.\r
+ *\r
+ * @param[in] sensor_comp : Variable which selects which data to be read from\r
+ * the sensor.\r
+ *\r
+ * sensor_comp | Macros\r
+ * ------------|-------------------\r
+ * 1 | BME280_PRESS\r
+ * 2 | BME280_TEMP\r
+ * 4 | BME280_HUM\r
+ * 7 | BME280_ALL\r
+ *\r
+ * @param[out] comp_data : Structure instance of bme280_data.\r
+ * @param[in] dev : Structure instance of bme280_dev.\r
+ *\r
+ * @return Result of API execution status\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_get_sensor_data(uint8_t sensor_comp, struct bme280_data *comp_data, struct bme280_dev *dev);\r
+\r
+/*!\r
+ * \ingroup bme280ApiSensorData\r
+ * \page bme280_api_bme280_parse_sensor_data bme280_parse_sensor_data\r
+ * \code\r
+ * void bme280_parse_sensor_data(const uint8_t *reg_data, struct bme280_uncomp_data *uncomp_data);\r
+ * \endcode\r
+ * @details This API is used to parse the pressure, temperature and\r
+ * humidity data and store it in the bme280_uncomp_data structure instance.\r
+ *\r
+ * @param[in] reg_data : Contains register data which needs to be parsed\r
+ * @param[out] uncomp_data : Contains the uncompensated pressure, temperature\r
+ * and humidity data.\r
+ *\r
+ */\r
+void bme280_parse_sensor_data(const uint8_t *reg_data, struct bme280_uncomp_data *uncomp_data);\r
+\r
+/*!\r
+ * \ingroup bme280ApiSensorData\r
+ * \page bme280_api_bme280_compensate_data bme280_compensate_data\r
+ * \code\r
+ * int8_t bme280_compensate_data(uint8_t sensor_comp,\r
+ * const struct bme280_uncomp_data *uncomp_data,\r
+ * struct bme280_data *comp_data,\r
+ * struct bme280_calib_data *calib_data);\r
+ * \endcode\r
+ * @details This API is used to compensate the pressure and/or\r
+ * temperature and/or humidity data according to the component selected by the\r
+ * user.\r
+ *\r
+ * @param[in] sensor_comp : Used to select pressure and/or temperature and/or\r
+ * humidity.\r
+ * @param[in] uncomp_data : Contains the uncompensated pressure, temperature and\r
+ * humidity data.\r
+ * @param[out] comp_data : Contains the compensated pressure and/or temperature\r
+ * and/or humidity data.\r
+ * @param[in] calib_data : Pointer to the calibration data structure.\r
+ *\r
+ * @return Result of API execution status.\r
+ *\r
+ * @retval 0 -> Success.\r
+ * @retval > 0 -> Warning.\r
+ * @retval < 0 -> Fail.\r
+ *\r
+ */\r
+int8_t bme280_compensate_data(uint8_t sensor_comp,\r
+ const struct bme280_uncomp_data *uncomp_data,\r
+ struct bme280_data *comp_data,\r
+ struct bme280_calib_data *calib_data);\r
+\r
+/**\r
+ * \ingroup bme280\r
+ * \defgroup bme280ApiSensorDelay Sensor Delay\r
+ * @brief Generic API for measuring sensor delay\r
+ */\r
+\r
+/*!\r
+ * \ingroup bme280ApiSensorDelay\r
+ * \page bme280_api_bme280_cal_meas_delay bme280_cal_meas_delay\r
+ * \code\r
+ * uint32_t bme280_cal_meas_delay(const struct bme280_settings *settings);\r
+ * \endcode\r
+ * @brief This API is used to calculate the maximum delay in milliseconds required for the\r
+ * temperature/pressure/humidity(which ever are enabled) measurement to complete.\r
+ * The delay depends upon the number of sensors enabled and their oversampling configuration.\r
+ *\r
+ * @param[in] settings : contains the oversampling configurations.\r
+ *\r
+ * @return delay required in milliseconds.\r
+ *\r
+ */\r
+uint32_t bme280_cal_meas_delay(const struct bme280_settings *settings);\r
+\r
+#ifdef __cplusplus\r
+}\r
+#endif /* End of CPP guard */\r
+#endif /* BME280_H_ */\r
+/** @}*/\r
projects / BME280_driver / blobdiff