[WHY]
Logging for SMU response value after the wait allows us to know
immediately what the response value was. Makes it easier to debug should
the value be anything other than OK.
[HOW]
Using the the already available DC SMU logging functions.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMD IOMMU driver cannot activate PASID mode on a RID without the RID's
translation being set to IDENTITY. Further it requires changing the RID's
page table layout from the normal v1 IOMMU_DOMAIN_IDENTITY layout to a
different v2 layout.
It does this by creating a new iommu_domain, configuring that domain for
v2 identity operation and then attaching it to the group, from within the
driver. This logic assumes the group is already set to the IDENTITY domain
and is being used by the DMA API.
However, since the ownership logic is based on the group's domain pointer
equaling the default domain to detect DMA API ownership, this causes it to
look like the group is not attached to the DMA API any more. This blocks
attaching drivers to any other devices in the group.
In a real system this manifests itself as the HD-audio devices on some AMD
platforms losing their device drivers.
Work around this unique behavior of the AMD driver by checking for
equality of IDENTITY domains based on their type, not their pointer
value. This allows the AMD driver to have two IDENTITY domains for
internal purposes without breaking the check.
Have the AMD driver properly declare that the special domain it created is
actually an IDENTITY domain.
Commit e8ae0e140c05 ("vfio: Require that devices support DMA cache
coherence") requires IOMMU drivers to advertise
IOMMU_CAP_CACHE_COHERENCY, in order to be used by VFIO. Since VFIO does
not provide to userspace the ability to maintain coherency through cache
invalidations, it requires hardware coherency. Advertise the capability
in order to restore VFIO support.
The meaning of IOMMU_CAP_CACHE_COHERENCY also changed from "IOMMU can
enforce cache coherent DMA transactions" to "IOMMU_CACHE is supported".
While virtio-iommu cannot enforce coherency (of PCIe no-snoop
transactions), it does support IOMMU_CACHE.
We can distinguish different cases of non-coherent DMA:
(1) When accesses from a hardware endpoint are not coherent. The host
would describe such a device using firmware methods ('dma-coherent'
in device-tree, '_CCA' in ACPI), since they are also needed without
a vIOMMU. In this case mappings are created without IOMMU_CACHE.
virtio-iommu doesn't need any additional support. It sends the same
requests as for coherent devices.
(2) When the physical IOMMU supports non-cacheable mappings. Supporting
those would require a new feature in virtio-iommu, new PROBE request
property and MAP flags. Device drivers would use a new API to
discover this since it depends on the architecture and the physical
IOMMU.
(3) When the hardware supports PCIe no-snoop. It is possible for
assigned PCIe devices to issue no-snoop transactions, and the
virtio-iommu specification is lacking any mention of this.
Arm platforms don't necessarily support no-snoop, and those that do
cannot enforce coherency of no-snoop transactions. Device drivers
must be careful about assuming that no-snoop transactions won't end
up cached; see commit e02f5c1bb228 ("drm: disable uncached DMA
optimization for ARM and arm64"). On x86 platforms, the host may or
may not enforce coherency of no-snoop transactions with the physical
IOMMU. But according to the above commit, on x86 a driver which
assumes that no-snoop DMA is compatible with uncached CPU mappings
will also work if the host enforces coherency.
Although these issues are not specific to virtio-iommu, it could be
used to facilitate discovery and configuration of no-snoop. This
would require a new feature bit, PROBE property and ATTACH/MAP
flags.
Cc: stable@vger.kernel.org Fixes: e8ae0e140c05 ("vfio: Require that devices support DMA cache coherence") Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Link: https://lore.kernel.org/r/20220825154622.86759-1-jean-philippe@linaro.org Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel IOMMU driver possibly selects between the first-level and the
second-level translation tables for DMA address translation. However,
the levels of page-table walks for the 4KB base page size are calculated
from the SAGAW field of the capability register, which is only valid for
the second-level page table. This causes the IOMMU driver to stop working
if the hardware (or the emulated IOMMU) advertises only first-level
translation capability and reports the SAGAW field as 0.
This solves the above problem by considering both the first level and the
second level when calculating the supported page table levels.
Fixes: b802d070a52a1 ("iommu/vt-d: Use iova over first level") Cc: stable@vger.kernel.org Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20220817023558.3253263-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC does not insert a `bti c` instruction at the beginning of a function
when it believes that all callers reach the function through a direct
branch[1]. Unfortunately the logic it uses to determine this is not
sufficiently robust, for example not taking account of functions being
placed in different sections which may be loaded separately, so we may
still see thunks being generated to these functions. If that happens,
the first instruction in the callee function will result in a Branch
Target Exception due to the missing landing pad.
While this has currently only been observed in the case of modules
having their main code loaded sufficiently far from their init section
to require thunks it could potentially happen for other cases so the
safest thing is to disable BTI for the kernel when building with an
affected toolchain.
Reported-by: D Scott Phillips <scott@os.amperecomputing.com>
[Bits of the commit message are lifted from his report & workaround] Signed-off-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20220905142255.591990-1-broonie@kernel.org Cc: <stable@vger.kernel.org> # v5.10+ Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace autoloading data based on the ACPI EC device with the DMI
records for motherboards models. The ACPI method created a bug that when
this driver returns error from the probe function because of the
unsupported motherboard model, the ACPI subsystem concludes
that the EC device does not work properly.
On Mon, Sep 12, 2022 at 10:52:45AM +0100, Catalin Marinas wrote:
>I missed this (holidays) and it looks like it's in stable already. On
>its own it will likely break kasan_hw if used together with user-space
>MTE as this change relies on two previous commits:
>
>70c248aca9e7 ("mm: kasan: Skip unpoisoning of user pages")
>6d05141a3930 ("mm: kasan: Skip page unpoisoning only if __GFP_SKIP_KASAN_UNPOISON")
>
>The reason I did not cc stable is that there are other dependencies in
>this area. The potential issues without the above commits were rather
>theoretical, so take these patches rather as clean-ups/refactoring than
>fixes.
In perf/Documentation/perf-stat.txt, for "--td-level" the default "0" means
the max level that the current hardware support.
So we need initialize the stat_config.topdown_level to TOPDOWN_MAX_LEVEL
when “--td-level=0” or no “--td-level” option. Otherwise, for the
hardware with a max level is 2, the 2nd level metrics disappear for raw
events in this case.
The issue cannot be observed for the perf stat default or "--topdown"
options. This commit fixes the raw events issue and removes the
duplicated code for the perf stat default.
Before:
# ./perf stat -e "cpu-clock,context-switches,cpu-migrations,page-faults,instructions,cycles,ref-cycles,branches,branch-misses,{slots,topdown-retiring,topdown-bad-spec,topdown-fe-bound,topdown-be-bound,topdown-heavy-ops,topdown-br-mispredict,topdown-fetch-lat,topdown-mem-bound}" sleep 1
Current perf stat uses the evlist__add_default_attrs() to add the
generic default attrs, and uses arch_evlist__add_default_attrs() to add
the Arch specific default attrs, e.g., Topdown for x86.
It works well for the non-hybrid platforms. However, for a hybrid
platform, the hard code generic default attrs don't work.
Uses arch_evlist__add_default_attrs() to replace the
evlist__add_default_attrs(). The arch_evlist__add_default_attrs() is
modified to invoke the same __evlist__add_default_attrs() for the
generic default attrs. No functional change.
Add default_null_attrs[] to indicate the arch specific attrs.
No functional change for the arch specific default attrs either.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Acked-by: Ian Rogers <irogers@google.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20220721065706.2886112-4-zhengjun.xing@linux.intel.com Signed-off-by: Xing Zhengjun <zhengjun.xing@linux.intel.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Stable-dep-of: f0c86a2bae4f ("perf stat: Fix L2 Topdown metrics disappear for raw events") Signed-off-by: Sasha Levin <sashal@kernel.org>
The global rwsem dmar_global_lock was introduced by commit 3a5670e8ac932
("iommu/vt-d: Introduce a rwsem to protect global data structures"). It
is used to protect DMAR related global data from DMAR hotplug operations.
The dmar_global_lock used in the intel_iommu_init() might cause recursive
locking issue, for example, intel_iommu_get_resv_regions() is taking the
dmar_global_lock from within a section where intel_iommu_init() already
holds it via probe_acpi_namespace_devices().
Using dmar_global_lock in intel_iommu_init() could be relaxed since it is
unlikely that any IO board must be hot added before the IOMMU subsystem is
initialized. This eliminates the possible recursive locking issue by moving
down DMAR hotplug support after the IOMMU is initialized and removing the
uses of dmar_global_lock in intel_iommu_init().
Configure ip-polling register to enable polling for all voltage monitor
channels.
This enables reading the voltage values for all inputs other than just
input 0.
Fix voltage allocation and reading to support all channels in all VMs.
Prior to this change allocation and reading were done only for the first
channel in each VM.
This change counts the total number of channels for allocation, and takes
into account the channel offset when reading the sample data register.
According to Moortec Embedded Voltage Monitor (MEVM) series 3 data
sheet, the minimum input signal is -100mv and maximum input signal
is +1000mv.
The equation used to convert the digital word to voltage uses mixed
types (*val signed and n unsigned), and on 64 bit machines also has
different size, since sizeof(u32) = 4 and sizeof(long) = 8.
So when measuring a negative input, n will be small enough, such that
PVT_N_CONST * n < PVT_R_CONST, and the result of
(PVT_N_CONST * n - PVT_R_CONST) will overflow to a very big positive
32 bit number. Then when storing the result in *val it will be the same
value just in 64 bit (instead of it representing a negative number which
will what happen when sizeof(long) = 4).
When -1023 <= (PVT_N_CONST * n - PVT_R_CONST) <= -1
dividing the number by 1024 should result of in 0, but because ">> 10"
is used, and the sign bit is used to fill the vacated bit positions, it
results in -1 (0xf...fffff) which is wrong.
This change fixes the sign problem and supports negative values by
casting n to long and replacing the shift right with div operation.
Bug - in case "intel,vm-map" is missing in device-tree ,'num' is set
to 0, and no voltage channel infos are allocated.
The reason num is set to 0 when "intel,vm-map" is missing is to set the
entire pvt->vm_idx[] with incremental channel numbers, but it didn't
take into consideration that same num is used later in devm_kcalloc().
If "intel,vm-map" does exist there is no need to set the unspecified
channels with incremental numbers, because the unspecified channels
can't be accessed in pvt_read_in() which is the only other place besides
the probe functions that uses pvt->vm_idx[].
This change fixes the bug by moving the incremental channel numbers
setting to be done only if "intel,vm-map" property is defined (starting
loop from 0), and removing 'num = 0'.
because the gate entry for TC 7 (S 0x80 10000 ns) now has a static guard
band added earlier than its 'gate close' event, such that packet
overruns won't occur in the worst case of the largest packet possible.
Since guard bands are statically determined based on the per-tc
QSYS_QMAXSDU_CFG_* with a fallback on the port-based QSYS_PORT_MAX_SDU,
we need to discuss what happens with TC 7 depending on kernel version,
since the driver, prior to commit 55a515b1f5a9 ("net: dsa: felix: drop
oversized frames with tc-taprio instead of hanging the port"), did not
touch QSYS_QMAXSDU_CFG_*, and therefore relied on QSYS_PORT_MAX_SDU.
1 (before vsc9959_tas_guard_bands_update): QSYS_PORT_MAX_SDU defaults to
1518, and at gigabit this introduces a static guard band (independent
of packet sizes) of 12144 ns, plus QSYS::HSCH_MISC_CFG.FRM_ADJ (bit
time of 20 octets => 160 ns). But this is larger than the time window
itself, of 10000 ns. So, the queue system never considers a frame with
TC 7 as eligible for transmission, since the gate practically never
opens, and these frames are forever stuck in the TX queues and hang
the port.
2 (after vsc9959_tas_guard_bands_update): Under the sole goal of
enabling oversized frame dropping, we make an effort to set
QSYS_QMAXSDU_CFG_7 to 1230 bytes. But QSYS_QMAXSDU_CFG_7 plays
one more role, which we did not take into account: per-tc static guard
band, expressed in L2 byte time (auto-adjusted for FCS and L1 overhead).
There is a discrepancy between what the driver thinks (that there is
no guard band, and 100% of min_gate_len[tc] is available for egress
scheduling) and what the hardware actually does (crops the equivalent
of QSYS_QMAXSDU_CFG_7 ns out of min_gate_len[tc]). In practice, this
means that the hardware thinks it has exactly 0 ns for scheduling tc 7.
In both cases, even minimum sized Ethernet frames are stuck on egress
rather than being considered for scheduling on TC 7, even if they would
fit given a proper configuration. Considering the current situation,
with vsc9959_tas_guard_bands_update(), frames between 60 octets and 1230
octets in size are not eligible for oversized dropping (because they are
smaller than QSYS_QMAXSDU_CFG_7), but won't be considered as eligible
for scheduling either, because the min_gate_len[7] (10000 ns) minus the
guard band determined by QSYS_QMAXSDU_CFG_7 (1230 octets * 8 ns per
octet == 9840 ns) minus the guard band auto-added for L1 overhead by
QSYS::HSCH_MISC_CFG.FRM_ADJ (20 octets * 8 ns per octet == 160 octets)
leaves 0 ns for scheduling in the queue system proper.
Investigating the hardware behavior, it becomes apparent that the queue
system needs precisely 33 ns of 'gate open' time in order to consider a
frame as eligible for scheduling to a tc. So the solution to this
problem is to amend vsc9959_tas_guard_bands_update(), by giving the
per-tc guard bands less space by exactly 33 ns, just enough for one
frame to be scheduled in that interval. This allows the queue system to
make forward progress for that port-tc, and prevents it from hanging.
Fixes: 297c4de6f780 ("net: dsa: felix: re-enable TAS guard band mode") Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Time-sensitive networking code needs to work with PTP times expressed in
nanoseconds, and with packet transmission times expressed in
picoseconds, since those would be fractional at higher than gigabit
speed when expressed in nanoseconds.
Convert the existing uses in tc-taprio and the ocelot/felix DSA driver
to a PSEC_PER_NSEC macro. This macro is placed in include/linux/time64.h
as opposed to its relatives (PSEC_PER_SEC etc) from include/vdso/time64.h
because the vDSO library does not (yet) need/use it.
Cc: Andy Lutomirski <luto@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com> # for the vDSO parts Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 11afdc6526de ("net: dsa: felix: tc-taprio intervals smaller than MTU should send at least one packet") Signed-off-by: Sasha Levin <sashal@kernel.org>
Crash dump always starts on CPU0. In case CPU0 is offline the
prefix page is not installed and the absolute zero lowcore is
used. However, struct lowcore::mcesad is never assigned and
stays zero. That leads to __machine_kdump() -> save_vx_regs()
call silently stores vector registers to the absolute lowcore
at 0x11b0 offset.
Fixes: a62bc0739253 ("s390/kdump: add support for vector extension") Reviewed-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We started using a 64 bit completion value. Unfortunately, we only
stored the low 32-bits, so a very large completion value would never
be matched in iommu_completion_wait().
Fixes: c69d89aff393 ("iommu/amd: Use 4K page for completion wait write-back semaphore") Signed-off-by: John Sperbeck <jsperbeck@google.com> Link: https://lore.kernel.org/r/20220801192229.3358786-1-jsperbeck@google.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The second operand passed to slot_addr() is declared as int or unsigned int
in all call sites. The left-shift to get the offset of a slot can overflow
if swiotlb size is larger than 4G.
Convert the macro to an inline function and declare the second argument as
phys_addr_t to avoid the potential overflow.
The unsolicited NA message with all-nodes multicast dest address should
be valid, as this also means the link could reach the target.
Also rename bond_validate_ns() to bond_validate_na().
Reported-by: LiLiang <liali@redhat.com> Fixes: 5e1eeef69c0f ("bonding: NS target should accept link local address") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The bonding driver piggybacks on time stamps kept by the network stack
for the purpose of the netdev TX watchdog, and this is problematic
because it does not work with NETIF_F_LLTX devices.
It is hard to say why the driver looks at dev_trans_start() of the
slave->dev, considering that this is updated even by non-ARP/NS probes
sent by us, and even by traffic not sent by us at all (for example PTP
on physical slave devices). ARP monitoring in active-backup mode appears
to still work even if we track only the last TX time of actual ARP
probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 592335a4164c ("bonding: accept unsolicited NA message") Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix HW rate limiting for ADQ.
Fallback to kernel queue selection for ADQ, as it is network stack
that decides which queue to use for transmit with ADQ configured.
Reset PF after creation of VMDq2 VSIs required for ADQ, as to
reprogram TX queue contexts in i40e_configure_tx_ring.
Without this patch PF would limit TX rate only according to TC0.
Fixes: a9ce82f744dc ("i40e: Enable 'channel' mode in mqprio for TC configs") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Limit io_uring "cmd" options to files for which the caller has
Smack read access. There may be cases where the cmd option may
be closer to a write access than a read, but there is no way
to make that determination.
Cc: stable@vger.kernel.org Fixes: ee692a21e9bf ("fs,io_uring: add infrastructure for uring-cmd") Signed-off-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a SELinux access control for the iouring IORING_OP_URING_CMD
command. This includes the addition of a new permission in the
existing "io_uring" object class: "cmd". The subject of the new
permission check is the domain of the process requesting access, the
object is the open file which points to the device/file that is the
target of the IORING_OP_URING_CMD operation. A sample policy rule
is shown below:
allow <domain> <file>:io_uring { cmd };
Cc: stable@vger.kernel.org Fixes: ee692a21e9bf ("fs,io_uring: add infrastructure for uring-cmd") Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
io-uring cmd support was added through ee692a21e9bf ("fs,io_uring:
add infrastructure for uring-cmd"), this extended the struct
file_operations to allow a new command which each subsystem can use
to enable command passthrough. Add an LSM specific for the command
passthrough which enables LSMs to inspect the command details.
This was discussed long ago without no clear pointer for something
conclusive, so this enables LSMs to at least reject this new file
operation.
A recent change in clang strengthened its -Wbitfield-constant-conversion
to warn when 1 is assigned to a 1-bit signed integer bitfield, as it can
only be 0 or -1, not 1:
sound/soc/atmel/mchp-spdiftx.c:505:20: error: implicit truncation from 'int' to bit-field changes value from 1 to -1 [-Werror,-Wbitfield-constant-conversion]
dev->gclk_enabled = 1;
^ ~
1 error generated.
The actual value of the field is never checked, just that it is not
zero, so there is not a real bug here. However, it is simple enough to
silence the warning by making the bitfield unsigned, which matches the
mchp-spdifrx driver.
The tps23861 registers are little-endian, and regmap_read_bulk() does
not do byte order conversion. On BE machines, the bytes were swapped,
and the interpretation of the resistance value was incorrect.
To make it work on both big and little-endian machines, use
le16_to_cpu() to convert the resitance register to host byte order.
Some calls to synthesis functions set err < 0 but only warn about the
failure and continue. However they do not set err back to zero, relying
on subsequent code to do that.
That changed with the introduction of option --synth. When --synth=no
subsequent functions that set err back to zero are not called.
Fix by setting err = 0 in those cases.
Example:
Before:
$ perf record --no-bpf-event --synth=all -o /tmp/huh uname
Couldn't synthesize bpf events.
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.014 MB /tmp/huh (7 samples) ]
$ perf record --no-bpf-event --synth=no -o /tmp/huh uname
Couldn't synthesize bpf events.
After:
$ perf record --no-bpf-event --synth=no -o /tmp/huh uname
Couldn't synthesize bpf events.
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.014 MB /tmp/huh (7 samples) ]
Fixes: 41b740b6e8a994e5 ("perf record: Add --synth option") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20220907162458.72817-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b91e5492f9d7ca89 ("perf record: Add a dummy event on hybrid
systems to collect metadata records") adds a dummy event on hybrid
systems to fix the symbol "unknown" issue when the workload is created
in a P-core but runs on an E-core. The added dummy event will cause
"perf script -F iregs" to fail. Dummy events do not have "iregs"
attribute set, so when we do evsel__check_attr, the "iregs" attribute
check will fail, so the issue happened.
The following commit [1] has fixed a similar issue by skipping the attr
check for the dummy event because it does not have any samples anyway. It
works okay for the normal mode, but the issue still happened when running
the test in the pipe mode. In the pipe mode, it calls process_attr() which
still checks the attr for the dummy event. This commit fixed the issue by
skipping the attr check for the dummy event in the API evsel__check_attr,
Otherwise, we have to patch everywhere when evsel__check_attr() is called.
Before:
#./perf record -o - --intr-regs=di,r8,dx,cx -e br_inst_retired.near_call:p -c 1000 --per-thread true 2>/dev/null|./perf script -F iregs |head -5
Samples for 'dummy:HG' event do not have IREGS attribute set. Cannot print 'iregs' field.
0x120 [0x90]: failed to process type: 64
#
The offending commit removed mmap_per_thread(), which did not consider
the different set-output rules for per-thread mmaps i.e. in the per-thread
case set-output is used for file descriptors of the same thread not the
same cpu.
This was not immediately noticed because it only happens with
multi-threaded targets and we do not have a test for that yet.
Reinstate mmap_per_thread() expanding it to cover also system-wide per-cpu
events i.e. to continue to allow the mixing of per-thread and per-cpu
mmaps.
Debug messages (with -vv) show the file descriptors that are opened with
sys_perf_event_open. New debug messages are added (needs -vvv) that show
also which file descriptors are mmapped and which are redirected with
set-output.
In the per-cpu case (cpu != -1) file descriptors for the same CPU are
set-output to the first file descriptor for that CPU.
In the per-thread case (cpu == -1) file descriptors for the same thread are
set-output to the first file descriptor for that thread.
Example (process 17489 has 2 threads):
Before (but with new debug prints):
$ perf record --no-bpf-event -vvv --per-thread -p 17489
<SNIP>
sys_perf_event_open: pid 17489 cpu -1 group_fd -1 flags 0x8 = 5
sys_perf_event_open: pid 17490 cpu -1 group_fd -1 flags 0x8 = 6
<SNIP>
libperf: idx 0: mmapping fd 5
libperf: idx 0: set output fd 6 -> 5
failed to mmap with 22 (Invalid argument)
After:
$ perf record --no-bpf-event -vvv --per-thread -p 17489
<SNIP>
sys_perf_event_open: pid 17489 cpu -1 group_fd -1 flags 0x8 = 5
sys_perf_event_open: pid 17490 cpu -1 group_fd -1 flags 0x8 = 6
<SNIP>
libperf: mmap_per_thread: nr cpu values (may include -1) 1 nr threads 2
libperf: idx 0: mmapping fd 5
libperf: idx 1: mmapping fd 6
<SNIP>
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.018 MB perf.data (15 samples) ]
Per-cpu example (process 20341 has 2 threads, same as above):
$ perf record --no-bpf-event -vvv -p 20341
<SNIP>
sys_perf_event_open: pid 20341 cpu 0 group_fd -1 flags 0x8 = 5
sys_perf_event_open: pid 20342 cpu 0 group_fd -1 flags 0x8 = 6
sys_perf_event_open: pid 20341 cpu 1 group_fd -1 flags 0x8 = 7
sys_perf_event_open: pid 20342 cpu 1 group_fd -1 flags 0x8 = 8
sys_perf_event_open: pid 20341 cpu 2 group_fd -1 flags 0x8 = 9
sys_perf_event_open: pid 20342 cpu 2 group_fd -1 flags 0x8 = 10
sys_perf_event_open: pid 20341 cpu 3 group_fd -1 flags 0x8 = 11
sys_perf_event_open: pid 20342 cpu 3 group_fd -1 flags 0x8 = 12
sys_perf_event_open: pid 20341 cpu 4 group_fd -1 flags 0x8 = 13
sys_perf_event_open: pid 20342 cpu 4 group_fd -1 flags 0x8 = 14
sys_perf_event_open: pid 20341 cpu 5 group_fd -1 flags 0x8 = 15
sys_perf_event_open: pid 20342 cpu 5 group_fd -1 flags 0x8 = 16
sys_perf_event_open: pid 20341 cpu 6 group_fd -1 flags 0x8 = 17
sys_perf_event_open: pid 20342 cpu 6 group_fd -1 flags 0x8 = 18
sys_perf_event_open: pid 20341 cpu 7 group_fd -1 flags 0x8 = 19
sys_perf_event_open: pid 20342 cpu 7 group_fd -1 flags 0x8 = 20
<SNIP>
libperf: mmap_per_cpu: nr cpu values 8 nr threads 2
libperf: idx 0: mmapping fd 5
libperf: idx 0: set output fd 6 -> 5
libperf: idx 1: mmapping fd 7
libperf: idx 1: set output fd 8 -> 7
libperf: idx 2: mmapping fd 9
libperf: idx 2: set output fd 10 -> 9
libperf: idx 3: mmapping fd 11
libperf: idx 3: set output fd 12 -> 11
libperf: idx 4: mmapping fd 13
libperf: idx 4: set output fd 14 -> 13
libperf: idx 5: mmapping fd 15
libperf: idx 5: set output fd 16 -> 15
libperf: idx 6: mmapping fd 17
libperf: idx 6: set output fd 18 -> 17
libperf: idx 7: mmapping fd 19
libperf: idx 7: set output fd 20 -> 19
<SNIP>
[ perf record: Woken up 7 times to write data ]
[ perf record: Captured and wrote 0.020 MB perf.data (17 samples) ]
Fixes: ae4f8ae16a078964 ("libperf evlist: Allow mixing per-thread and per-cpu mmaps") Reported-by: Tomáš Trnka <trnka@scm.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=216441 Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20220905114209.8389-1-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cong Wang noticed that the previous fix for sch_sfb accessing the queued
skb after enqueueing it to a child qdisc was incomplete: the SFB enqueue
function was also calling qdisc_qstats_backlog_inc() after enqueue, which
reads the pkt len from the skb cb field. Fix this by also storing the skb
len, and using the stored value to increment the backlog after enqueueing.
Fixes: 9efd23297cca ("sch_sfb: Don't assume the skb is still around after enqueueing to child") Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Acked-by: Cong Wang <cong.wang@bytedance.com> Link: https://lore.kernel.org/r/20220905192137.965549-1-toke@toke.dk Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently phy link up/down interrupt is enabled using the
LAN87xx_INTERRUPT_MASK register. In the lan87xx_read_status function,
phy link is determined using the T1_MODE_STAT_REG register comm_ready bit.
comm_ready bit is set using the loc_rcvr_status & rem_rcvr_status.
Whenever the phy link is up, LAN87xx_INTERRUPT_SOURCE link_up bit is set
first but comm_ready bit takes some time to set based on local and
remote receiver status.
As per the current implementation, interrupt is triggered using link_up
but the comm_ready bit is still cleared in the read_status function. So,
link is always down. Initially tested with the shared interrupt
mechanism with switch and internal phy which is working, but after
implementing interrupt controller it is not working.
It can fixed either by updating the read_status function to read from
LAN87XX_INTERRUPT_SOURCE register or enable the interrupt mask for
comm_ready bit. But the validation team recommends the use of comm_ready
for link detection.
This patch fixes by enabling the comm_ready bit for link_up in the
LAN87XX_INTERRUPT_MASK_2 register (MISC Bank) and link_down in
LAN87xx_INTERRUPT_MASK register.
When we queue a request via tw for execution it's not going to be
executed immediately, so when io_queue_async() hits IO_APOLL_READY
and queues a tw but doesn't try to recycle/consume the buffer some other
request may try to use the the buffer.
After modifying the QP to the Error state, all RX WR would be completed
with WC in IB_WC_WR_FLUSH_ERR status. Current implementation does not
wait for it is done, but destroy the QP and free the link group directly.
So there is a risk that accessing the freed memory in tasklet context.
Fixes: bd4ad57718cc ("smc: initialize IB transport incl. PD, MR, QP, CQ, event, WR") Signed-off-by: Yacan Liu <liuyacan@corp.netease.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set ib1 state to MTK_FOE_STATE_UNBIND in __mtk_foe_entry_clear routine.
Fixes: 33fc42de33278 ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The read-modify-write of QSYS_TAG_CONFIG from vsc9959_sched_speed_set()
runs unlocked with respect to the other functions that access it, which
are vsc9959_tas_guard_bands_update(), vsc9959_qos_port_tas_set() and
vsc9959_tas_clock_adjust(). All the others are under ocelot->tas_lock,
so move the vsc9959_sched_speed_set() access under that lock as well, to
resolve the concurrency.
Fixes: 55a515b1f5a9 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Experimentally, it looks like when QSYS_QMAXSDU_CFG_7 is set to 605,
frames even way larger than 601 octets are transmitted even though these
should be considered as oversized, according to the documentation, and
dropped.
Since oversized frame dropping depends on frame size, which is only
known at the EOF stage, and therefore not at SOF when cut-through
forwarding begins, it means that the switch cannot take QSYS_QMAXSDU_CFG_*
into consideration for traffic classes that are cut-through.
Since cut-through forwarding has no UAPI to control it, and the driver
enables it based on the mantra "if we can, then why not", the strategy
is to alter vsc9959_cut_through_fwd() to take into consideration which
tc's have oversize frame dropping enabled, and disable cut-through for
them. Then, from vsc9959_tas_guard_bands_update(), we re-trigger the
cut-through determination process.
There are 2 strategies for vsc9959_cut_through_fwd() to determine
whether a tc has oversized dropping enabled or not. One is to keep a bit
mask of traffic classes per port, and the other is to read back from the
hardware registers (a non-zero value of QSYS_QMAXSDU_CFG_* means the
feature is enabled). We choose reading back from registers, because
struct ocelot_port is shared with drivers (ocelot, seville) that don't
support either cut-through nor tc-taprio, and we don't have a felix
specific extension of struct ocelot_port. Furthermore, reading registers
from the Felix hardware is quite cheap, since they are memory-mapped.
Fixes: 55a515b1f5a9 ("net: dsa: felix: drop oversized frames with tc-taprio instead of hanging the port") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a QP and a MR on a local host are in different PDs, the HW generates
an asynchronous event (AE). The same AE is generated when a QP and a MW
are in different PDs during a bind operation. Return the more appropriate
IBV_WC_MW_BIND_ERR for the latter case by checking the OP type from the
CQE in error.
Maximum Active Resources (MAR) and Maximum Open Resources (MOR) are 0's
based vales where a value of 0xffffffff indicates that there is no limit.
Decrement the values that are returned by bdev_max_open_zones and
bdev_max_active_zones as the block layer helpers are not 0's based.
A 0 returned by the block layer helpers indicates no limit, thus convert
it to 0xffffffff (U32_MAX).
Fixes: aaf2e048af27 ("nvmet: add ZBD over ZNS backend support") Suggested-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Dennis Maisenbacher <dennis.maisenbacher@wdc.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This will increase the number of data chunks by the number of devices,
not only increase system chunk usage, but also greatly increase mount
time.
Without a proper reason, we should not change the max chunk size.
[CAUSE]
Previously, we set max data chunk size to 10G, while max data stripe
length to 1G.
Commit f6fca3917b4d ("btrfs: store chunk size in space-info struct")
completely ignored the 10G limit, but use 1G max stripe limit instead,
causing above shrink in max data chunk size.
[FIX]
Fix the max data chunk size to 10G, and in decide_stripe_size_regular()
we limit stripe_size to 1G manually.
This should only affect data chunks, as for metadata chunks we always
set the max stripe size the same as max chunk size (256M or 1G
depending on fs size).
Fix a bug reported and analyzed by Nagaraj Arankal, where the handling
of a spurious non-SACK RTO could cause a connection to fail to clear
retrans_stamp, causing a later RTO to very prematurely time out the
connection with ETIMEDOUT.
Here is the buggy scenario, expanding upon Nagaraj Arankal's excellent
report:
(*1) Send one data packet on a non-SACK connection
(*2) Because no ACK packet is received, the packet is retransmitted
and we enter CA_Loss; but this retransmission is spurious.
(*3) The ACK for the original data is received. The transmitted packet
is acknowledged. The TCP timestamp is before the retrans_stamp,
so tcp_may_undo() returns true, and tcp_try_undo_loss() returns
true without changing state to Open (because tcp_is_sack() is
false), and tcp_process_loss() returns without calling
tcp_try_undo_recovery(). Normally after undoing a CA_Loss
episode, tcp_fastretrans_alert() would see that the connection
has returned to CA_Open and fall through and call
tcp_try_to_open(), which would set retrans_stamp to 0. However,
for non-SACK connections we hold the connection in CA_Loss, so do
not fall through to call tcp_try_to_open() and do not set
retrans_stamp to 0. So retrans_stamp is (erroneously) still
non-zero.
At this point the first "retransmission event" has passed and
been recovered from. Any future retransmission is a completely
new "event". However, retrans_stamp is erroneously still
set. (And we are still in CA_Loss, which is correct.)
(*4) After 16 minutes (to correspond with tcp_retries2=15), a new data
packet is sent. Note: No data is transmitted between (*3) and
(*4) and we disabled keep alives.
The socket's timeout SHOULD be calculated from this point in
time, but instead it's calculated from the prior "event" 16
minutes ago (step (*2)).
(*5) Because no ACK packet is received, the packet is retransmitted.
(*6) At the time of the 2nd retransmission, the socket returns
ETIMEDOUT, prematurely, because retrans_stamp is (erroneously)
too far in the past (set at the time of (*2)).
This commit fixes this bug by ensuring that we reuse in
tcp_try_undo_loss() the same careful logic for non-SACK connections
that we have in tcp_try_undo_recovery(). To avoid duplicating logic,
we factor out that logic into a new
tcp_is_non_sack_preventing_reopen() helper and call that helper from
both undo functions.
When we queue requests, we strive to batch as much as possible and also
signal the network stack that more data is about to be sent over a socket
with MSG_SENDPAGE_NOTLAST. This flag looks at the pending requests queued
as well as queue->more_requests that is derived from the block layer
last-in-batch indication.
We set more_request=true when we flush the request directly from
.queue_rq submission context (in nvme_tcp_send_all), however this is
wrongly assuming that no other requests may be queued during the
execution of nvme_tcp_send_all.
Due to this, a race condition may happen where:
1. request X is queued as !last-in-batch
2. request X submission context calls nvme_tcp_send_all directly
3. nvme_tcp_send_all is preempted and schedules to a different cpu
4. request Y is queued as last-in-batch
5. nvme_tcp_send_all context sends request X+Y, however signals for
both MSG_SENDPAGE_NOTLAST because queue->more_requests=true.
==> none of the requests is pushed down to the wire as the network
stack is waiting for more data, both requests timeout.
To fix this, we eliminate queue->more_requests and only rely on
the queue req_list and send_list to be not-empty.
Fixes: 122e5b9f3d37 ("nvme-tcp: optimize network stack with setting msg flags according to batch size") Reported-by: Jonathan Nicklin <jnicklin@blockbridge.com> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Tested-by: Jonathan Nicklin <jnicklin@blockbridge.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should also bail from the io_work loop when we set rd_enabled to true,
so we don't attempt to read data from the socket when the TCP stream is
already out-of-sync or corrupted.
Fixes: 3f2304f8c6d6 ("nvme-tcp: add NVMe over TCP host driver") Reported-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
During stress testing with CONFIG_SMP disabled, KASAN reports as below:
==================================================================
BUG: KASAN: use-after-free in __mutex_lock+0xe5/0xc30
Read of size 8 at addr ffff8881094223f8 by task stress/7789
CPU: 0 PID: 7789 Comm: stress Not tainted 6.0.0-rc1-00002-g0d53d2e882f9 #3
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Call Trace:
<TASK>
..
__mutex_lock+0xe5/0xc30
..
z_erofs_do_read_page+0x8ce/0x1560
..
z_erofs_readahead+0x31c/0x580
..
Freed by task 7787
kasan_save_stack+0x1e/0x40
kasan_set_track+0x20/0x30
kasan_set_free_info+0x20/0x40
__kasan_slab_free+0x10c/0x190
kmem_cache_free+0xed/0x380
rcu_core+0x3d5/0xc90
__do_softirq+0x12d/0x389
Last potentially related work creation:
kasan_save_stack+0x1e/0x40
__kasan_record_aux_stack+0x97/0xb0
call_rcu+0x3d/0x3f0
erofs_shrink_workstation+0x11f/0x210
erofs_shrink_scan+0xdc/0x170
shrink_slab.constprop.0+0x296/0x530
drop_slab+0x1c/0x70
drop_caches_sysctl_handler+0x70/0x80
proc_sys_call_handler+0x20a/0x2f0
vfs_write+0x555/0x6c0
ksys_write+0xbe/0x160
do_syscall_64+0x3b/0x90
The root cause is that erofs_workgroup_unfreeze() doesn't reset to
orig_val thus it causes a race that the pcluster reuses unexpectedly
before freeing.
Since UP platforms are quite rare now, such path becomes unnecessary.
Let's drop such specific-designed path directly instead.
Since commit 6a921de58992 ("btrfs: zoned: introduce
space_info->active_total_bytes"), we're only counting the bytes of a
block group on an active zone as usable for metadata writes. But on a
SMR drive, we don't have active zones and short circuit some of the
logic.
This leads to an error on mount, because we cannot reserve space for
metadata writes.
Fix this by also setting the BLOCK_GROUP_FLAG_ZONE_IS_ACTIVE bit in the
block-group's runtime flag if the zone is a conventional zone.
Fixes: 6a921de58992 ("btrfs: zoned: introduce space_info->active_total_bytes") Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When accessing Ports Performance Counters Register (PPCNT),
local port must be one if it is Function-Per-Port HCA that
HCA_CAP.num_ports is 1.
The offending patch can change the local port to other values
when accessing PPCNT after enabling switchdev mode. The following
syndrome will be printed:
# cat /sys/class/infiniband/rdmap4s0f0/ports/2/counters/*
# dmesg
mlx5_core 0000:04:00.0: mlx5_cmd_check:756:(pid 12450): ACCESS_REG(0x805) op_mod(0x1) failed, status bad parameter(0x3), syndrome (0x1e5585)
Fix it by setting local port to one for Function-Per-Port HCA.
Fix a nested dead lock as part of ODP flow by using mmput_async().
From the below call trace [1] can see that calling mmput() once we have
the umem_odp->umem_mutex locked as required by
ib_umem_odp_map_dma_and_lock() might trigger in the same task the
exit_mmap()->__mmu_notifier_release()->mlx5_ib_invalidate_range() which
may dead lock when trying to lock the same mutex.
Moving to use mmput_async() will solve the problem as the above
exit_mmap() flow will be called in other task and will be executed once
the lock will be available.
The SRv6 layer allows defining HMAC data that can later be used to sign IPv6
Segment Routing Headers. This configuration is realised via netlink through
four attributes: SEG6_ATTR_HMACKEYID, SEG6_ATTR_SECRET, SEG6_ATTR_SECRETLEN and
SEG6_ATTR_ALGID. Because the SECRETLEN attribute is decoupled from the actual
length of the SECRET attribute, it is possible to provide invalid combinations
(e.g., secret = "", secretlen = 64). This case is not checked in the code and
with an appropriately crafted netlink message, an out-of-bounds read of up
to 64 bytes (max secret length) can occur past the skb end pointer and into
skb_shared_info:
Breakpoint 1, seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208
208 memcpy(hinfo->secret, secret, slen);
(gdb) bt
#0 seg6_genl_sethmac (skb=<optimized out>, info=<optimized out>) at net/ipv6/seg6.c:208
#1 0xffffffff81e012e9 in genl_family_rcv_msg_doit (skb=skb@entry=0xffff88800b1f9f00, nlh=nlh@entry=0xffff88800b1b7600,
extack=extack@entry=0xffffc90000ba7af0, ops=ops@entry=0xffffc90000ba7a80, hdrlen=4, net=0xffffffff84237580 <init_net>, family=<optimized out>,
family=<optimized out>) at net/netlink/genetlink.c:731
#2 0xffffffff81e01435 in genl_family_rcv_msg (extack=0xffffc90000ba7af0, nlh=0xffff88800b1b7600, skb=0xffff88800b1f9f00,
family=0xffffffff82fef6c0 <seg6_genl_family>) at net/netlink/genetlink.c:775
#3 genl_rcv_msg (skb=0xffff88800b1f9f00, nlh=0xffff88800b1b7600, extack=0xffffc90000ba7af0) at net/netlink/genetlink.c:792
#4 0xffffffff81dfffc3 in netlink_rcv_skb (skb=skb@entry=0xffff88800b1f9f00, cb=cb@entry=0xffffffff81e01350 <genl_rcv_msg>)
at net/netlink/af_netlink.c:2501
#5 0xffffffff81e00919 in genl_rcv (skb=0xffff88800b1f9f00) at net/netlink/genetlink.c:803
#6 0xffffffff81dff6ae in netlink_unicast_kernel (ssk=0xffff888010eec800, skb=0xffff88800b1f9f00, sk=0xffff888004aed000)
at net/netlink/af_netlink.c:1319
#7 netlink_unicast (ssk=ssk@entry=0xffff888010eec800, skb=skb@entry=0xffff88800b1f9f00, portid=portid@entry=0, nonblock=<optimized out>)
at net/netlink/af_netlink.c:1345
#8 0xffffffff81dff9a4 in netlink_sendmsg (sock=<optimized out>, msg=0xffffc90000ba7e48, len=<optimized out>) at net/netlink/af_netlink.c:1921
...
(gdb) p/x ((struct sk_buff *)0xffff88800b1f9f00)->head + ((struct sk_buff *)0xffff88800b1f9f00)->end
$1 = 0xffff88800b1b76c0
(gdb) p/x secret
$2 = 0xffff88800b1b76c0
(gdb) p slen
$3 = 64 '@'
The OOB data can then be read back from userspace by dumping HMAC state. This
commit fixes this by ensuring SECRETLEN cannot exceed the actual length of
SECRET.
Reported-by: Lucas Leong <wmliang.tw@gmail.com>
Tested: verified that EINVAL is correctly returned when secretlen > len(secret) Fixes: 4f4853dc1c9c1 ("ipv6: sr: implement API to control SR HMAC structure") Signed-off-by: David Lebrun <dlebrun@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a link is enslave to bond, it need to set the interface down first.
This makes the slave remove mac multicast address 33:33:00:00:00:01(The
IPv6 multicast address ff02::1 is kept even when the interface down). When
bond set the slave up, ipv6_mc_up() was not called due to commit c2edacf80e15
("bonding / ipv6: no addrconf for slaves separately from master").
This is not an issue before we adding the lladdr target feature for bonding,
as the mac multicast address will be added back when bond interface up and
join group ff02::1.
But after adding lladdr target feature for bonding. When user set a lladdr
target, the unsolicited NA message with all-nodes multicast dest will be
dropped as the slave interface never add 33:33:00:00:00:01 back.
Fix this by calling ipv6_mc_up() to add 33:33:00:00:00:01 back when
the slave interface up.
Reported-by: LiLiang <liali@redhat.com> Fixes: 5e1eeef69c0f ("bonding: NS target should accept link local address") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When ns_ip6_target was set, the ipv6_dev_get_saddr() will be called to get
available source address and send IPv6 neighbor solicit message.
If the target is global address, ipv6_dev_get_saddr() will get any
available src address. But if the target is link local address,
ipv6_dev_get_saddr() will only get available address from our interface,
i.e. the corresponding bond interface.
But before bond interface up, all the address is tentative, while
ipv6_dev_get_saddr() will ignore tentative address. This makes we can't
find available link local src address, then bond_ns_send() will not be
called and no NS message was sent. Finally bond interface will keep in
down state.
Fix this by sending NS with unspecified address if there is no available
source address.
Reported-by: LiLiang <liali@redhat.com> Fixes: 5e1eeef69c0f ("bonding: NS target should accept link local address") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Functions that work on a pointer to virtual memory such as
virt_to_pfn() and users of that function such as
virt_to_page() are supposed to pass a pointer to virtual
memory, ideally a (void *) or other pointer. However since
many architectures implement virt_to_pfn() as a macro,
this function becomes polymorphic and accepts both a
(unsigned long) and a (void *).
If we instead implement a proper virt_to_pfn(void *addr)
function the following happens (occurred on arch/arm):
drivers/infiniband/sw/siw/siw_qp_tx.c:32:23: warning: incompatible
integer to pointer conversion passing 'dma_addr_t' (aka 'unsigned int')
to parameter of type 'const void *' [-Wint-conversion]
drivers/infiniband/sw/siw/siw_qp_tx.c:32:37: warning: passing argument
1 of 'virt_to_pfn' makes pointer from integer without a cast
[-Wint-conversion]
drivers/infiniband/sw/siw/siw_qp_tx.c:538:36: warning: incompatible
integer to pointer conversion passing 'unsigned long long'
to parameter of type 'const void *' [-Wint-conversion]
Fix this with an explicit cast. In one case where the SIW
SGE uses an unaligned u64 we need a double cast modifying the
virtual address (va) to a platform-specific uintptr_t before
casting to a (void *).
Commit b9684a71fca7 ("block, loop: support partitions without scanning")
adds GD_SUPPRESS_PART_SCAN for replacing part function of
GENHD_FL_NO_PART. But looks blk_add_partitions() is missed, since
loop doesn't want to add partitions if GENHD_FL_NO_PART was set.
And it causes regression on libblockdev (as called from udisks) which
operates with the LO_FLAGS_PARTSCAN.
Fixes the issue by not adding partitions if GD_SUPPRESS_PART_SCAN is
set.
Fixes: b9684a71fca7 ("block, loop: support partitions without scanning") Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20220823103819.395776-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Removing 'hotplug-status' in backend_disconnected() means that it will be
removed even in the case that the frontend unilaterally disconnects (which
it is free to do at any time). The consequence of this is that, when the
frontend attempts to re-connect, the backend gets stuck in 'InitWait'
rather than moving straight to 'Connected' (which it can do because the
hotplug script has already run).
Instead, the 'hotplug-status' mode should be removed in netback_remove()
i.e. when the vif really is going away.
Fixes: 0f4558ae9187 ("Revert "xen-netback: remove 'hotplug-status' once it has served its purpose"") Signed-off-by: Paul Durrant <pdurrant@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
iavf_reset_task() takes crit_lock at the beginning and holds
it during whole call. The function subsequently calls
iavf_init_interrupt_scheme() that grabs RTNL. Problem occurs
when userspace initiates during the reset task any ndo callback
that runs under RTNL like iavf_open() because some of that
functions tries to take crit_lock. This leads to classic A-B B-A
deadlock scenario.
To resolve this situation the device should be detached in
iavf_reset_task() prior taking crit_lock to avoid subsequent
ndos running under RTNL and reattach the device at the end.
Fixes: 62fe2a865e6d ("i40evf: add missing rtnl_lock() around i40evf_set_interrupt_capability") Cc: Jacob Keller <jacob.e.keller@intel.com> Cc: Patryk Piotrowski <patryk.piotrowski@intel.com> Cc: SlawomirX Laba <slawomirx.laba@intel.com> Tested-by: Vitaly Grinberg <vgrinber@redhat.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver incorrectly frees client instance and subsequent
i40e module removal leads to kernel crash.
Reproducer:
1. Do ethtool offline test followed immediately by another one
host# ethtool -t eth0 offline; ethtool -t eth0 offline
2. Remove recursively irdma module that also removes i40e module
host# modprobe -r irdma
Two offline tests cause IRDMA driver failure (ETIMEDOUT) and this
failure is indicated back to i40e_client_subtask() that calls
i40e_client_del_instance() to free client instance referenced
by pf->cinst and sets this pointer to NULL. During the module
removal i40e_remove() calls i40e_lan_del_device() that dereferences
pf->cinst that is NULL -> crash.
Do not remove client instance when client open callbacks fails and
just clear __I40E_CLIENT_INSTANCE_OPENED bit. The driver also needs
to take care about this situation (when netdev is up and client
is NOT opened) in i40e_notify_client_of_netdev_close() and
calls client close callback only when __I40E_CLIENT_INSTANCE_OPENED
is set.
Fixes: 0ef2d5afb12d ("i40e: KISS the client interface") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Tested-by: Helena Anna Dubel <helena.anna.dubel@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix leak, when user changes ring parameters.
During reallocation of RX buffers, new DMA mappings are created for
those buffers. New buffers with different RX ring count should
substitute older ones, but those buffers were freed in ice_vsi_cfg_rxq
and reallocated again with ice_alloc_rx_buf. kfree on rx_buf caused
leak of already mapped DMA.
Reallocate ZC with xdp_buf struct, when BPF program loads. Reallocate
back to rx_buf, when BPF program unloads.
If BPF program is loaded/unloaded and XSK pools are created, reallocate
RX queues accordingly in XDP_SETUP_XSK_POOL handler.
Steps for reproduction:
while :
do
for ((i=0; i<=8160; i=i+32))
do
ethtool -G enp130s0f0 rx $i tx $i
sleep 0.5
ethtool -g enp130s0f0
done
done
Fixes: 617f3e1b588c ("ice: xsk: allocate separate memory for XDP SW ring") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Chandan <chandanx.rout@intel.com> (A Contingent Worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We got a recent syzbot report [1] showing a possible misuse
of pfmemalloc page status in TCP zerocopy paths.
Indeed, for pages coming from user space or other layers,
using page_is_pfmemalloc() is moot, and possibly could give
false positives.
There has been attempts to make page_is_pfmemalloc() more robust,
but not using it in the first place in this context is probably better,
removing cpu cycles.
Note to stable teams :
You need to backport 84ce071e38a6 ("net: introduce
__skb_fill_page_desc_noacc") as a prereq.
Race is more probable after commit c07aea3ef4d4
("mm: add a signature in struct page") because page_is_pfmemalloc()
is now using low order bit from page->lru.next, which can change
more often than page->index.
Low order bit should never be set for lru.next (when used as an anchor
in LRU list), so KCSAN report is mostly a false positive.
Backporting to older kernel versions seems not necessary.
[1]
BUG: KCSAN: data-race in lru_add_fn / tcp_build_frag
value changed: 0x0000000000000000 -> 0xffffea0004a1d288
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 18611 Comm: syz-executor.4 Not tainted 6.0.0-rc2-syzkaller-00248-ge022620b5d05-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 07/22/2022
Fixes: c07aea3ef4d4 ("mm: add a signature in struct page") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Managed pages contain pinned userspace pages and controlled by upper
layers, there is no need in tracking skb->pfmemalloc for them. Introduce
a helper for filling frags but ignoring page tracking, it'll be needed
later.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a shift wrapping bug in this code so anything thing above
31 will return false.
Fixes: 35c55c9877f8 ("tipc: add neighbor monitoring framework") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sch_sfb enqueue() routine assumes the skb is still alive after it has
been enqueued into a child qdisc, using the data in the skb cb field in the
increment_qlen() routine after enqueue. However, the skb may in fact have
been freed, causing a use-after-free in this case. In particular, this
happens if sch_cake is used as a child of sfb, and the GSO splitting mode
of CAKE is enabled (in which case the skb will be split into segments and
the original skb freed).
Fix this by copying the sfb cb data to the stack before enqueueing the skb,
and using this stack copy in increment_qlen() instead of the skb pointer
itself.
Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-18231 Fixes: e13e02a3c68d ("net_sched: SFB flow scheduler") Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 2c87c6f9fbddc5b84d67b2fa3f432fcac6d99d93.
Meanwhile it turned out that the following commit is the proper
workaround for the issue that 2c87c6f9fbdd tries to address. a3a57bf07de2 ("net: stmmac: work around sporadic tx issue on link-up")
It's nor clear why the to be reverted commit helped for one user,
for others it didn't make a difference.
When replacing KUNIT_BINARY_*_MSG_ASSERTION() macros with
KUNIT_BINARY_INT_ASSERTION(), the assert_type parameter was not always
correctly transferred. Specifically, the following errors were
introduced:
- KUNIT_EXPECT_LE_MSG() uses KUNIT_ASSERTION
- KUNIT_ASSERT_LT_MSG() uses KUNIT_EXPECTATION
- KUNIT_ASSERT_GT_MSG() uses KUNIT_EXPECTATION
A failing KUNIT_EXPECT_LE_MSG() test thus prevents further tests from
running, while failing KUNIT_ASSERT_{LT,GT}_MSG() tests do not prevent
further tests from running. This is contrary to the documentation,
which states that failing KUNIT_EXPECT_* macros allow further tests to
run, while failing KUNIT_ASSERT_* macros should prevent this.
Revert the KUNIT_{ASSERTION,EXPECTATION} switches to fix the behaviour
for the affected macros.
rxrpc and kafs between them try to use the receive timestamp on the first
data packet (ie. the one with sequence number 1) as a base from which to
calculate the time at which callback promise and lock expiration occurs.
However, we don't know how long it took for the server to send us the reply
from it having completed the basic part of the operation - it might then,
for instance, have to send a bunch of a callback breaks, depending on the
particular operation.
Fix this by using the time at which the operation is issued on the client
as a base instead. That should never be longer than the server's idea of
the expiry time.
Fixes: 781070551c26 ("afs: Fix calculation of callback expiry time") Fixes: 2070a3e44962 ("rxrpc: Allow the reply time to be obtained on a client call") Suggested-by: Jeffrey E Altman <jaltman@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
rxkad_verify_packet_2() has a small stack-allocated sglist of 4 elements,
but if that isn't sufficient for the number of fragments in the socket
buffer, we try to allocate an sglist large enough to hold all the
fragments.
However, for large packets with a lot of fragments, this isn't sufficient
and we need at least one additional fragment.
The problem manifests as skb_to_sgvec() returning -EMSGSIZE and this then
getting returned by userspace. Most of the time, this isn't a problem as
rxrpc sets a limit of 5692, big enough for 4 jumbo subpackets to be glued
together; occasionally, however, the server will ignore the reported limit
and give a packet that's a lot bigger - say 19852 bytes with ->nr_frags
being 7. skb_to_sgvec() then tries to return a "zeroth" fragment that
seems to occur before the fragments counted by ->nr_frags and we hit the
end of the sglist too early.
Note that __skb_to_sgvec() also has an skb_walk_frags() loop that is
recursive up to 24 deep. I'm not sure if I need to take account of that
too - or if there's an easy way of counting those frags too.
Fix this by counting an extra frag and allocating a larger sglist based on
that.
Fixes: d0d5c0cd1e71 ("rxrpc: Use skb_unshare() rather than skb_cow_data()") Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Because rxrpc pretends to be a tunnel on top of a UDP/UDP6 socket, allowing
it to siphon off UDP packets early in the handling of received UDP packets
thereby avoiding the packet going through the UDP receive queue, it doesn't
get ICMP packets through the UDP ->sk_error_report() callback. In fact, it
doesn't appear that there's any usable option for getting hold of ICMP
packets.
Fix this by adding a new UDP encap hook to distribute error messages for
UDP tunnels. If the hook is set, then the tunnel driver will be able to
see ICMP packets. The hook provides the offset into the packet of the UDP
header of the original packet that caused the notification.
An alternative would be to call the ->error_handler() hook - but that
requires that the skbuff be cloned (as ip_icmp_error() or ipv6_cmp_error()
do, though isn't really necessary or desirable in rxrpc's case is we want
to parse them there and then, not queue them).
Changes
=======
ver #3)
- Fixed an uninitialised variable.
ver #2)
- Fixed some missing CONFIG_AF_RXRPC_IPV6 conditionals.
Fixes: 5271953cad31 ("rxrpc: Use the UDP encap_rcv hook") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the delayed registration is specified via either delayed_register
option or the quirk, we delay the invocation of snd_card_register()
until the given interface. But if a wrong value has been set there
and there are more interfaces over the given interface number,
snd_card_register() call would be missing for those interfaces.
This patch catches up those missing calls by fixing the comparison of
the interface number. Now the call is skipped only if the processed
interface is less than the given interface, instead of the exact
match.
The info message that was added in the commit a4aad5636c72 ("ALSA:
usb-audio: Inform devices that need delayed registration") is actually
useful to know the need for the delayed registration. However, it
turned out that this doesn't catch the all cases; namely, this warned
only when a PCM stream is attached onto the existing PCM instance, but
it doesn't count for a newly created PCM instance. This made
confusion as if there were no further delayed registration.
This patch moves the check to the code path for either adding a stream
or creating a PCM instance. Also, make it simpler by checking the
card->registered flag instead of querying each snd_device state.
Ensure the match happens in the right direction, previously the
destination used was the server, not the NAT host, as the comment
shows the code intended.
Additionally nf_nat_irc uses port 0 as a signal and there's no valid way
it can appear in a DCC message, so consider port 0 also forged.
PolarFire SoC does not have the same l2 cache controller as the fu540,
featuring an extra interrupt. Appease the devicetree checker overlords
by adding a PolarFire SoC specific compatible to fix the below sort of
warnings:
mpfs-polarberry.dtb: cache-controller@2010000: interrupts: [[1], [3], [4], [2]] is too long
The IPv6 path already drops dst in the daddr changed case, but the IPv4
path does not. This change makes the two code paths consistent.
Further, it is possible that there is already a metadata_dst allocated from
ingress that might already be attached to skbuff->dst while following
the bridge path. If it is not released before setting a new
metadata_dst, it will be leaked. This is similar to what is done in
bpf_set_tunnel_key() or ip6_route_input().
It is important to note that the memory being leaked is not the dst
being set in the bridge code, but rather memory allocated from some
other code path that is not being freed correctly before the skb dst is
overwritten.
An example of the leakage fixed by this commit found using kmemleak:
On SAMA7G5, when resuming from backup and self-refresh, the bootloader
performs DDR PHY recalibration by restoring the value of ZQ0SR0 (stored
in RAM by Linux before going to backup and self-refresh). It has been
discovered that the current procedure doesn't work for all possible values
that might go to ZQ0SR0 due to hardware bug. The workaround to this is to
avoid storing some values in ZQ0SR0. Thus Linux will read the ZQ0SR0
register and cache its value in RAM after processing it (using
modified_gray_code array). The bootloader will restore the processed value.
Fixes: d2d4716d8384 ("ARM: at91: pm: save ddr phy calibration data to securam") Suggested-by: Frederic Schumacher <frederic.schumacher@microchip.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20220826083927.3107272-4-claudiu.beznea@microchip.com Signed-off-by: Sasha Levin <sashal@kernel.org>
It has been discovered that on some parts, from time to time, self-refresh
procedure doesn't work as expected. Debugging and investigating it proved
that disabling AC DLL introduce glitches in RAM controllers which
leads to unexpected behavior. This is confirmed as a hardware bug. DLL
bypass disables 3 DLLs: 2 DX DLLs and AC DLL. Thus, keep only DX DLLs
disabled. This introduce 6mA extra current consumption on VDDCORE when
switching to any ULP mode or standby mode but the self-refresh procedure
still works.
Fixes: f0bbf17958e8 ("ARM: at91: pm: add self-refresh support for sama7g5") Suggested-by: Frederic Schumacher <frederic.schumacher@microchip.com> Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Tested-by: Cristian Birsan <cristian.birsan@microchip.com> Link: https://lore.kernel.org/r/20220826083927.3107272-3-claudiu.beznea@microchip.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Sometimes 'wilc_sdio_cmd53' is called with addresses pointing to an
object on the stack. Use dynamically allocated memory for cmd53 instead
of stack address which is not DMA'able.
Fixes: 5625f965d764 ("wilc1000: move wilc driver out of staging") Reported-by: Michael Walle <mwalle@kernel.org> Suggested-by: Michael Walle <mwalle@kernel.org> Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Reviewed-by: Michael Walle <mwalle@kernel.org> Tested-by: Michael Walle <mwalle@kernel.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220809075749.62752-1-ajay.kathat@microchip.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The bt number of qpc_timer of HIP09 increases compared with that of HIP08.
Therefore, qpc_timer_bt_num and num_qpc_timer do not match. As a result,
the driver may fail to allocate qpc_timer. So the driver needs to uniquely
uses qpc_timer_bt_num to represent the bt number of qpc_timer.
Fixes: 0e40dc2f70cd ("RDMA/hns: Add timer allocation support for hip08") Link: https://lore.kernel.org/r/20220829105021.1427804-4-liangwenpeng@huawei.com Signed-off-by: Yixing Liu <liuyixing1@huawei.com> Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log