Fix the order of source and destination addresses when resolving the
route between server and client to validate use of correct net device.
The reverse order we had so far didn't actually validate the net device
as the server would try to resolve the route to itself, thus always
getting the server's net device.
The issue was discovered when running cm applications on a single host
between 2 interfaces with same subnet and source based routing rules.
When resolving the reverse route the source based route rules were
ignored.
Include <linux/uaccess.h> to avoid the warning:
drivers/tee/tee_shm.c: In function 'tee_shm_register':
>> drivers/tee/tee_shm.c:242:14: error: implicit declaration of function 'access_ok' [-Werror=implicit-function-declaration]
242 | if (!access_ok((void __user *)addr, length))
| ^~~~~~~~~
cc1: some warnings being treated as errors
If regulator_enable() fails, enable_count is incremented still.
A consumer, assuming no matching regulator_disable() is necessary on
failure, will then get this error message upon regulator_put()
since enable_count is non-zero:
[ 1.277418] WARNING: CPU: 3 PID: 1 at drivers/regulator/core.c:2304 _regulator_put.part.0+0x168/0x170
The consumer could try to fix this in their driver by cleaning up on
error from regulator_enable() (i.e. call regulator_disable()), but that
results in the following since regulator_enable() failed and didn't
increment user_count:
[ 1.258112] unbalanced disables for vreg_l17c
[ 1.262606] WARNING: CPU: 4 PID: 1 at drivers/regulator/core.c:2899 _regulator_disable+0xd4/0x190
Fix this by decrementing enable_count upon failure to enable.
With this in place, just the reason for failure to enable is printed
as expected and developers can focus on the root cause of their issue
instead of thinking their usage of the regulator consumer api is
incorrect. For example, in my case:
[ 1.240426] vreg_l17c: invalid input voltage found
Fixes: 5451781dadf8 ("regulator: core: Only count load for enabled consumers") Signed-off-by: Andrew Halaney <ahalaney@redhat.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Brian Masney <bmasney@redhat.com> Link: https://lore.kernel.org/r/20220819194336.382740-1-ahalaney@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
smb3 fallocate punch hole was not grabbing the inode or filemap_invalidate
locks so could have race with pagemap reinstantiating the page.
Cc: stable@vger.kernel.org Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bringing up a CPU may involve creating and destroying tasks which requires
read-locking threadgroup_rwsem, so threadgroup_rwsem nests inside
cpus_read_lock(). However, cpuset's ->attach(), which may be called with
thredagroup_rwsem write-locked, also wants to disable CPU hotplug and
acquires cpus_read_lock(), leading to a deadlock.
Fix it by guaranteeing that ->attach() is always called with CPU hotplug
disabled and removing cpus_read_lock() call from cpuset_attach().
Signed-off-by: Tejun Heo <tj@kernel.org> Reviewed-and-tested-by: Imran Khan <imran.f.khan@oracle.com> Reported-and-tested-by: Xuewen Yan <xuewen.yan@unisoc.com> Fixes: 05c7b7a92cc8 ("cgroup/cpuset: Fix a race between cpuset_attach() and cpu hotplug") Cc: stable@vger.kernel.org # v5.17+ Signed-off-by: Sasha Levin <sashal@kernel.org>
cgroup_update_dfl_csses() write-lock the threadgroup_rwsem as updating the
csses can trigger process migrations. However, if the subtree doesn't
contain any tasks, there aren't gonna be any cgroup migrations. This
condition can be trivially detected by testing whether
mgctx.preloaded_src_csets is empty. Elide write-locking threadgroup_rwsem if
the subtree is empty.
After this optimization, the usage pattern of creating a cgroup, enabling
the necessary controllers, and then seeding it with CLONE_INTO_CGROUP and
then removing the cgroup after it becomes empty doesn't need to write-lock
threadgroup_rwsem at all.
Signed-off-by: Tejun Heo <tj@kernel.org> Cc: Christian Brauner <brauner@kernel.org> Cc: Michal Koutný <mkoutny@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A lot of modern laptops use the Parade PS8461E MUX for eDP
switching. The MUX can operate in jitter cleaning mode or
redriver mode, the first one resulting in higher link
quality. The jitter cleaning mode needs to know the link
rate used and the MUX achieves this by snooping the
LINK_BW_SET, LINK_RATE_SELECT and SUPPORTED_LINK_RATES
DPCD accesses.
When the MUX is powered down (seems this can happen whenever
the display is turned off) it loses track of the snooped
link rates so when we do the LINK_RATE_SELECT write it no
longer knowns which link rate we're selecting, and thus it
falls back to the lower quality redriver mode. This results
in unstable high link rates (eg. usually 8.1Gbps link rate
no longer works correctly).
In order to avoid all that let's re-snoop SUPPORTED_LINK_RATES
from the sink at the start of every link training.
Unfortunately we don't have a way to detect the presence of
the MUX. It looks like the set of laptops equipped with this
MUX is fairly large and contains devices from multiple
manufacturers. It may also still be growing with new models.
So a quirk doesn't seem like a very easily maintainable
option, thus we shall attempt to do this unconditionally on
all machines that use LINK_RATE_SELECT. Hopefully this extra
DPCD read doesn't cause issues for any unaffected machine.
If that turns out to be the case we'll need to convert this
into a quirk in the future.
Cc: stable@vger.kernel.org Cc: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6205 Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220902070319.15395-1-ville.syrjala@linux.intel.com Tested-by: Aaron Ma <aaron.ma@canonical.com> Tested-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 25899c590cb5ba9b9f284c6ca8e7e9086793d641) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a very common pattern of using
debugfs_remove(debufs_lookup(..)) which results in a dentry leak of the
dentry that was looked up. Instead of having to open-code the correct
pattern of calling dput() on the dentry, create
debugfs_lookup_and_remove() to handle this pattern automatically and
properly without any memory leaks.
The system call gate area counts as kernel text but trying
to install a kprobe in this area fails with an Oops later on.
To fix this explicitly disallow the gate area for kprobes.
There may be a bad USB audio device with a USB ID of (0x04fa, 0x4201) and
the number of it's interfaces less than 4, an out-of-bounds read bug occurs
when parsing the interface descriptor for this device.
In loopback_jiffies_timer_pos_update(), we are getting jiffies twice.
First time for playback, second time for capture. Jiffies can be updated
between these two calls and if the capture jiffies is larger, extra zeros
will be filled in the capture buffer.
Change to get jiffies once and use it for both playback and capture.
The voice allocator sometimes begins allocating from near the end of the
array and then wraps around, however snd_emu10k1_pcm_channel_alloc()
accesses the newly allocated voices as if it never wrapped around.
This results in out of bounds access if the first voice has a high enough
index so that first_voice + requested_voice_count > NUM_G (64).
The more voices are requested, the more likely it is for this to occur.
This was initially discovered using PipeWire, however it can be reproduced
by calling aplay multiple times with 16 channels:
aplay -r 48000 -D plughw:CARD=Live,DEV=3 -c 16 /dev/zero
UBSAN: array-index-out-of-bounds in sound/pci/emu10k1/emupcm.c:127:40
index 65 is out of range for type 'snd_emu10k1_voice [64]'
CPU: 1 PID: 31977 Comm: aplay Tainted: G W IOE 6.0.0-rc2-emu10k1+ #7
Hardware name: ASUSTEK COMPUTER INC P5W DH Deluxe/P5W DH Deluxe, BIOS 3002 07/22/2010
Call Trace:
<TASK>
dump_stack_lvl+0x49/0x63
dump_stack+0x10/0x16
ubsan_epilogue+0x9/0x3f
__ubsan_handle_out_of_bounds.cold+0x44/0x49
snd_emu10k1_playback_hw_params+0x3bc/0x420 [snd_emu10k1]
snd_pcm_hw_params+0x29f/0x600 [snd_pcm]
snd_pcm_common_ioctl+0x188/0x1410 [snd_pcm]
? exit_to_user_mode_prepare+0x35/0x170
? do_syscall_64+0x69/0x90
? syscall_exit_to_user_mode+0x26/0x50
? do_syscall_64+0x69/0x90
? exit_to_user_mode_prepare+0x35/0x170
snd_pcm_ioctl+0x27/0x40 [snd_pcm]
__x64_sys_ioctl+0x95/0xd0
do_syscall_64+0x5c/0x90
? do_syscall_64+0x69/0x90
? do_syscall_64+0x69/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Though acpi_find_last_cache_level() always returned signed value and the
document states it will return any errors caused by lack of a PPTT table,
it never returned negative values before.
Commit 0c80f9e165f8 ("ACPI: PPTT: Leave the table mapped for the runtime usage")
however changed it by returning -ENOENT if no PPTT was found. The value
returned from acpi_find_last_cache_level() is then assigned to unsigned
fw_level.
It will result in the number of cache leaves calculated incorrectly as
a huge value which will then cause the following warning from __alloc_pages
as the order would be great than MAX_ORDER because of incorrect and huge
cache leaves value.
If a 32-bit kernel was compiled for PA2.0 CPUs, it won't be able to run
on machines with PA1.x CPUs. Add a check and bail out early if a PA1.x
machine is detected.
Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Zhenneng Li <lizhenneng@kylinos.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
V1:
The amdgpu_xgmi_remove_device function will send unload command
to psp through psp ring to terminate xgmi, but psp ring has been
destroyed in psp_hw_fini.
V2:
1. Change the commit title.
2. Restore amdgpu_xgmi_remove_device to its original calling location.
Move psp_xgmi_terminate call from amdgpu_xgmi_remove_device to
psp_hw_fini.
This partially reverts commit d2b292c3f6fd ("scsi: qla2xxx: Enable ATIO
interrupt handshake for ISP27XX")
For some workloads where the host sends a batch of commands and then
pauses, ATIO interrupt coalesce can cause some incoming ATIO entries to be
ignored for extended periods of time, resulting in slow performance,
timeouts, and aborted commands.
Disable interrupt coalesce and re-enable the dedicated ATIO MSI-X
interrupt.
Link: https://lore.kernel.org/r/97dcf365-89ff-014d-a3e5-1404c6af511c@cybernetics.com Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: Nilesh Javali <njavali@marvell.com> Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 23c2d497de21 ("mm: kmemleak: take a full lowmem check in
kmemleak_*_phys()") brought false leak alarms on some archs like arm64
that does not init pfn boundary in early booting. The final solution
lands on linux-6.0: commit 0c24e061196c ("mm: kmemleak: add rbtree and
store physical address for objects allocated with PA").
Revert this commit before linux-6.0. The original issue of invalid PA
can be mitigated by additional check in devicetree.
Commit d4252071b97d ("add barriers to buffer_uptodate and
set_buffer_uptodate") added proper memory barriers to the buffer head
BH_Uptodate bit, so that anybody who tests a buffer for being up-to-date
will be guaranteed to actually see initialized state.
However, that commit didn't _just_ add the memory barrier, it also ended
up dropping the "was it already set" logic that the BUFFER_FNS() macro
had.
That's conceptually the right thing for a generic "this is a memory
barrier" operation, but in the case of the buffer contents, we really
only care about the memory barrier for the _first_ time we set the bit,
in that the only memory ordering protection we need is to avoid anybody
seeing uninitialized memory contents.
Any other access ordering wouldn't be about the BH_Uptodate bit anyway,
and would require some other proper lock (typically BH_Lock or the folio
lock). A reader that races with somebody invalidating the buffer head
isn't an issue wrt the memory ordering, it's a serialization issue.
Now, you'd think that the buffer head operations don't matter in this
day and age (and I certainly thought so), but apparently some loads
still end up being heavy users of buffer heads. In particular, the
kernel test robot reported that not having this bit access optimization
in place caused a noticeable direct IO performance regression on ext4:
This reverts commit a8eb8e6f7159c7c20c0ddac428bde3d110890aa7 as
it can cause invalid link quality command sent to the firmware
and address the off-by-one issue by fixing condition of while loop.
Cc: stable@vger.kernel.org Fixes: a8eb8e6f7159 ("wifi: iwlegacy: 4965: fix potential off-by-one overflow in il4965_rs_fill_link_cmd()") Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220815073737.GA999388@wp.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race condition may occur if the user calls close() on another thread
during a write() operation on the device node of the efi capsule.
This is a race condition that occurs between the efi_capsule_write() and
efi_capsule_flush() functions of efi_capsule_fops, which ultimately
results in UAF.
So, the page freeing process is modified to be done in
efi_capsule_release() instead of efi_capsule_flush().
The EFI stub is a wrapper around the core kernel that makes it look like
a EFI compatible PE/COFF application to the EFI firmware. EFI
applications run on top of the EFI runtime, which is heavily based on
so-called protocols, which are struct types consisting [mostly] of
function pointer members that are instantiated and recorded in a
protocol database.
These structs look like the ideal randomization candidates to the
randstruct plugin (as they only carry function pointers), but of course,
these protocols are contracts between the firmware that exposes them,
and the EFI applications (including our stubbed kernel) that invoke
them. This means that struct randomization for EFI protocols is not a
great idea, and given that the stub shares very little data with the
core kernel that is represented as a randomizable struct, we're better
off just disabling it completely here.
Cc: <stable@vger.kernel.org> # v4.14+ Reported-by: Daniel Marth <daniel.marth@inso.tuwien.ac.at> Tested-by: Daniel Marth <daniel.marth@inso.tuwien.ac.at> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: sleeping function called from invalid context at kernel/printk/printk.c:2347
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 1105, name: syz-executor423
3 locks held by syz-executor423/1105:
#0: ffff8881468b9098 (&tty->ldisc_sem){++++}-{0:0}, at: tty_ldisc_ref_wait+0x22/0x90 drivers/tty/tty_ldisc.c:266
#1: ffff8881468b9130 (&tty->atomic_write_lock){+.+.}-{3:3}, at: tty_write_lock drivers/tty/tty_io.c:952 [inline]
#1: ffff8881468b9130 (&tty->atomic_write_lock){+.+.}-{3:3}, at: do_tty_write drivers/tty/tty_io.c:975 [inline]
#1: ffff8881468b9130 (&tty->atomic_write_lock){+.+.}-{3:3}, at: file_tty_write.constprop.0+0x2a8/0x8e0 drivers/tty/tty_io.c:1118
#2: ffff88801b06c398 (&gsm->tx_lock){....}-{2:2}, at: gsmld_write+0x5e/0x150 drivers/tty/n_gsm.c:2717
irq event stamp: 3482
hardirqs last enabled at (3481): [<ffffffff81d13343>] __get_reqs_available+0x143/0x2f0 fs/aio.c:946
hardirqs last disabled at (3482): [<ffffffff87d39722>] __raw_spin_lock_irqsave include/linux/spinlock_api_smp.h:108 [inline]
hardirqs last disabled at (3482): [<ffffffff87d39722>] _raw_spin_lock_irqsave+0x52/0x60 kernel/locking/spinlock.c:159
softirqs last enabled at (3408): [<ffffffff87e01002>] asm_call_irq_on_stack+0x12/0x20
softirqs last disabled at (3401): [<ffffffff87e01002>] asm_call_irq_on_stack+0x12/0x20
Preemption disabled at:
[<0000000000000000>] 0x0
CPU: 2 PID: 1105 Comm: syz-executor423 Not tainted 5.10.137-syzkaller #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x107/0x167 lib/dump_stack.c:118
___might_sleep.cold+0x1e8/0x22e kernel/sched/core.c:7304
console_lock+0x19/0x80 kernel/printk/printk.c:2347
do_con_write+0x113/0x1de0 drivers/tty/vt/vt.c:2909
con_write+0x22/0xc0 drivers/tty/vt/vt.c:3296
gsmld_write+0xd0/0x150 drivers/tty/n_gsm.c:2720
do_tty_write drivers/tty/tty_io.c:1028 [inline]
file_tty_write.constprop.0+0x502/0x8e0 drivers/tty/tty_io.c:1118
call_write_iter include/linux/fs.h:1903 [inline]
aio_write+0x355/0x7b0 fs/aio.c:1580
__io_submit_one fs/aio.c:1952 [inline]
io_submit_one+0xf45/0x1a90 fs/aio.c:1999
__do_sys_io_submit fs/aio.c:2058 [inline]
__se_sys_io_submit fs/aio.c:2028 [inline]
__x64_sys_io_submit+0x18c/0x2f0 fs/aio.c:2028
do_syscall_64+0x33/0x40 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x61/0xc6
The problem happens in the following control flow:
gsmld_write(...)
spin_lock_irqsave(&gsm->tx_lock, flags) // taken a spinlock on TX data
con_write(...)
do_con_write(...)
console_lock()
might_sleep() // -> bug
As far as console_lock() might sleep it should not be called with
spinlock held.
The patch replaces tx_lock spinlock with mutex in order to avoid the
problem.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
syzbot is reporting use of uninitialized spinlock at gsmld_write() [1], for
commit 32dd59f ("tty: n_gsm: fix race condition in gsmld_write()")
allows accessing gsm->tx_lock before gsm_activate_mux() initializes it.
Since object initialization should be done right after allocation in order
to avoid accessing uninitialized memory, move initialization of
timer/work/waitqueue/spinlock from gsmld_open()/gsm_activate_mux() to
gsm_alloc_mux().
Xen blkfront advertises its support of the persistent grants feature
when it first setting up and when resuming in 'talk_to_blkback()'.
Then, blkback reads the advertised value when it connects with blkfront
and decides if it will use the persistent grants feature or not, and
advertises its decision to blkfront. Blkfront reads the blkback's
decision and it also makes the decision for the use of the feature.
Commit 402c43ea6b34 ("xen-blkfront: Apply 'feature_persistent' parameter
when connect"), however, made the blkfront's read of the parameter for
disabling the advertisement, namely 'feature_persistent', to be done
when it negotiate, not when advertise. Therefore blkfront advertises
without reading the parameter. As the field for caching the parameter
value is zero-initialized, it always advertises as the feature is
disabled, so that the persistent grants feature becomes always disabled.
This commit fixes the issue by making the blkfront does parmeter caching
just before the advertisement.
Fixes: 402c43ea6b34 ("xen-blkfront: Apply 'feature_persistent' parameter when connect") Cc: <stable@vger.kernel.org> # 5.10.x Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: SeongJae Park <sj@kernel.org> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220831165824.94815-4-sj@kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RFC 8881 explains the purpose of the write verifier this way:
> The final portion of the result is the field writeverf. This field
> is the write verifier and is a cookie that the client can use to
> determine whether a server has changed instance state (e.g., server
> restart) between a call to WRITE and a subsequent call to either
> WRITE or COMMIT.
But then it says:
> This cookie MUST be unchanged during a single instance of the
> NFSv4.1 server and MUST be unique between instances of the NFSv4.1
> server. If the cookie changes, then the client MUST assume that
> any data written with an UNSTABLE4 value for committed and an old
> writeverf in the reply has been lost and will need to be
> recovered.
RFC 1813 has similar language for NFSv3. NFSv2 does not have a write
verifier since it doesn't implement the COMMIT procedure.
Since commit 19e0663ff9bc ("nfsd: Ensure sampling of the write
verifier is atomic with the write"), the Linux NFS server has
returned a boot-time-based verifier for UNSTABLE WRITEs, but a zero
verifier for FILE_SYNC and DATA_SYNC WRITEs. FILE_SYNC and DATA_SYNC
WRITEs are not followed up with a COMMIT, so there's no need for
clients to compare verifiers for stable writes.
However, by returning a different verifier for stable and unstable
writes, the above commit puts the Linux NFS server a step farther
out of compliance with the first MUST above. At least one NFS client
(FreeBSD) noticed the difference, making this a potential
regression.
[Removed down_write to fix the conflict in the cherry-pick. The
down_write functionality was no longer needed there. Upstream commit 555dbf1a9aac6d3150c8b52fa35f768a692f4eeb titled nfsd: Replace use of
rwsem with errseq_t removed those and replace it with new functionality
that was more scalable. This commit is already backported onto 5.10 and
so removing down_write ensures consistency with that change. Tested by
compiling and booting successfully. - kochera]
At least one older CH341 appears to have the RX timer enable bit
inverted so that setting it disables the RX timer and prevents the FIFO
from emptying until it is full.
Only set the RX timer enable bit for devices with version newer than
0x27 (even though this probably affects all pre-0x30 devices).
Reported-by: Jonathan Woithe <jwoithe@just42.net> Tested-by: Jonathan Woithe <jwoithe@just42.net> Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au Fixes: 4e46c410e050 ("USB: serial: ch341: reinitialize chip on reconfiguration") Cc: stable@vger.kernel.org # 4.10 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable LCR updates for pre-0x30 devices which use a different (unknown)
protocol for line control and where the current register write causes
the next received character to be lost.
Note that updating LCR using the INIT command has no effect on these
devices either.
Reported-by: Jonathan Woithe <jwoithe@just42.net> Tested-by: Jonathan Woithe <jwoithe@just42.net> Link: https://lore.kernel.org/r/Ys1iPTfiZRWj2gXs@marvin.atrad.com.au Fixes: 4e46c410e050 ("USB: serial: ch341: reinitialize chip on reconfiguration") Fixes: 55fa15b5987d ("USB: serial: ch341: fix baud rate and line-control handling") Cc: stable@vger.kernel.org # 4.10 Signed-off-by: Johan Hovold <johan@kernel.org>
[ johan: adjust context to 5.15 ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc3 driver manages its PHYs itself so the USB core PHY management
needs to be disabled.
Use the struct xhci_plat_priv hack added by commits 46034a999c07 ("usb:
host: xhci-plat: add platform data support") and f768e718911e ("usb:
host: xhci-plat: add priv quirk for skip PHY initialization") to
propagate the setting for now.
Fixes: 4e88d4c08301 ("usb: add a flag to skip PHY initialization to struct usb_hcd") Fixes: 178a0bce05cb ("usb: core: hcd: integrate the PHY wrapper into the HCD core") Tested-by: Matthias Kaehlcke <mka@chromium.org> Cc: stable <stable@kernel.org> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20220825131836.19769-1-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ johan: adjust context to 5.15 ] Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm dwc3 runtime-PM implementation checks the xhci
platform-device pointer in the wakeup-interrupt handler to determine
whether the controller is in host mode and if so triggers a resume.
After a role switch in OTG mode the xhci platform-device would have been
freed and the next wakeup from runtime suspend would access the freed
memory.
Note that role switching is executed from a freezable workqueue, which
guarantees that the pointer is stable during suspend.
Also note that runtime PM has been broken since commit 2664deb09306
("usb: dwc3: qcom: Honor wakeup enabled/disabled state"), which
incidentally also prevents this issue from being triggered.
When introduced, upon success, the 1.8V fixup workaround in
mmc_sd_init_card() would branch to practically the end of the function, to
a label named "done". Unfortunately, perhaps due to the label name, over
time new code has been added that really should have come after "done" not
before it. Let's fix the problem by moving the label to the correct place
and rename it "cont".
Fixes: 045d705dc1fb ("mmc: core: Enable the MMC host software queue for the SD card") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Seunghui Lee <sh043.lee@samsung.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220815073321.63382-2-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Backport to 5.10] Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Identifying and removing the stale device from the fs_uuids list is done
by btrfs_free_stale_devices(). btrfs_free_stale_devices() in turn
depends on device_path_matched() to check if the device appears in more
than one btrfs_device structure.
The matching of the device happens by its path, the device path. However,
when device mapper is in use, the dm device paths are nothing but a link
to the actual block device, which leads to the device_path_matched()
failing to match.
Fix this by matching the dev_t as provided by lookup_bdev() instead of
plain string compare of the device paths.
Reported-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's been reported that there is a possible data-race accessing to the
global card_requested[] array at ALSA sequencer core, which is used
for determining whether to call request_module() for the card or not.
This data race itself is almost harmless, as it might end up with one
extra request_module() call for the already loaded module at most.
But it's still better to fix.
This patch addresses the possible data race of card_requested[] and
client_requested[] arrays by replacing them with bitmask.
It's an atomic operation and can work without locks.
ALSA OSS sequencer refers to a global variable max_midi_devs at
creating a new port, storing it to its own field. Meanwhile this
variable may be changed by other sequencer events at
snd_seq_oss_midi_check_exit_port() in parallel, which may cause a data
race.
OTOH, this data race itself is almost harmless, as the access to the
MIDI device is done via get_mdev() and it's protected with a refcount,
hence its presence is guaranteed.
Though, it's sill better to address the data-race from the code sanity
POV, and this patch adds the proper spinlock for the protection.
Upon reception, a packet must be categorized, either it's destination is
the host, or it is another host. A packet with no destination addressing
fields may be valid in two situations:
- the packet has no source field: only ACKs are built like that, we
consider the host as the destination.
- the packet has a valid source field: it is directed to the PAN
coordinator, as for know we don't have this information we consider we
are not the PAN coordinator.
There was likely a copy/paste error made during a previous cleanup
because the if clause is now containing exactly the same condition as in
the switch case, which can never be true. In the past the destination
address was used in the switch and the source address was used in the
if, which matches what the spec says.
Cc: stable@vger.kernel.org Fixes: ae531b9475f6 ("ieee802154: use ieee802154_addr instead of *_sa variants") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20220826142954.254853-1-miquel.raynal@bootlin.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the
reader is in preemptible context and the writer side
(u64_stats_update_begin*()) runs in an interrupt context (IRQ or
softirq) then the writer can update the stats during the read operation.
This update remains undetected.
Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP
are not interrupted by a writer. 32bit-SMP remains unaffected by this
change.
Cc: "David S. Miller" <davem@davemloft.net> Cc: Catherine Sullivan <csully@google.com> Cc: David Awogbemila <awogbemila@google.com> Cc: Dimitris Michailidis <dmichail@fungible.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Jeroen de Borst <jeroendb@google.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Simon Horman <simon.horman@corigine.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Cc: oss-drivers@corigine.com Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__mkroute_input() uses fib_validate_source() to trigger an icmp redirect.
My understanding is that fib_validate_source() is used to know if the src
address and the gateway address are on the same link. For that,
fib_validate_source() returns 1 (same link) or 0 (not the same network).
__mkroute_input() is the only user of these positive values, all other
callers only look if the returned value is negative.
Since the below patch, fib_validate_source() didn't return anymore 1 when
both addresses are on the same network, because the route lookup returns
RT_SCOPE_LINK instead of RT_SCOPE_HOST. But this is, in fact, right.
Let's adapat the test to return 1 again when both addresses are on the same
link.
CC: stable@vger.kernel.org Fixes: 747c14307214 ("ip: fix dflt addr selection for connected nexthop") Reported-by: kernel test robot <yujie.liu@intel.com> Reported-by: Heng Qi <hengqi@linux.alibaba.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20220829100121.3821-1-nicolas.dichtel@6wind.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ieee80211_scan_rx() tries to access scan_req->flags after a
null check, but a UAF is observed when the scan is completed
and __ieee80211_scan_completed() executes, which then calls
cfg80211_scan_done() leading to the freeing of scan_req.
Since scan_req is rcu_dereference()'d, prevent the racing in
__ieee80211_scan_completed() by ensuring that from mac80211's
POV it is no longer accessed from an RCU read critical section
before we call cfg80211_scan_done().
When we are not connected to a channel, sending channel "switch"
announcement doesn't make any sense.
The BSS list is empty in that case. This causes the for loop in
cfg80211_get_bss() to be bypassed, so the function returns NULL
(check line 1424 of net/wireless/scan.c), causing the WARN_ON()
in ieee80211_ibss_csa_beacon() to get triggered (check line 500
of net/mac80211/ibss.c), which was consequently reported on the
syzkaller dashboard.
Thus, check if we have an existing connection before generating
the CSA beacon in ieee80211_ibss_finish_csa().
Both __device_attach_driver() and __driver_attach() check the return
code of the bus_type.match() function to see if the device needs to be
added to the deferred probe list. After adding the device to the list,
the logic attempts to bind the device to the driver anyway, as if the
device had matched with the driver, which is not correct.
If __device_attach_driver() detects that the device in question is not
ready to match with a driver on the bus, then it doesn't make sense for
the device to attempt to bind with the current driver or continue
attempting to match with any of the other drivers on the bus. So, update
the logic in __device_attach_driver() to reflect this.
If __driver_attach() detects that a driver tried to match with a device
that is not ready to match yet, then the driver should not attempt to bind
with the device. However, the driver can still attempt to match and bind
with other devices on the bus, as drivers can be bound to multiple
devices. So, update the logic in __driver_attach() to reflect this.
During cdrom emulation, the response to read_toc command must contain
the cdrom address as the number of sectors (2048 byte sized blocks)
represented either as an absolute value (when MSF bit is '0') or in
terms of PMin/PSec/PFrame (when MSF bit is set to '1'). Incase of
cdrom, the fsg_lun_open call sets the sector size to 2048 bytes.
When MAC OS sends a read_toc request with MSF set to '1', the
store_cdrom_address assumes that the address being provided is the
LUN size represented in 512 byte sized blocks instead of 2048. It
tries to modify the address further to convert it to 2048 byte sized
blocks and store it in MSF format. This results in data transfer
failures as the cdrom address being provided in the read_toc response
is incorrect.
This turned out not to be an error in usb-storage but rather a nested
device reset attempt. That is, as the rtl8712 driver was being
unbound from a composite device in preparation for an unrelated USB
reset (that driver does not have pre_reset or post_reset callbacks),
its ->remove routine called usb_reset_device() -- thus nesting one
reset call within another.
Performing a reset as part of disconnect processing is a questionable
practice at best. However, the bug report points out that the USB
core does not have any protection against nested resets. Adding a
reset_in_progress flag and testing it will prevent such errors in the
future.
Add proper alignment for .nospec_call_table and .nospec_return_table in
vmlinux.
[hca@linux.ibm.com]: The problem with the missing alignment of the nospec
tables exist since a long time, however only since commit e6ed91fd0768
("s390/alternatives: remove padding generation code") and with
CONFIG_RELOCATABLE=n the kernel may also crash at boot time.
The above named commit reduced the size of struct alt_instr by one byte,
so its new size is 11 bytes. Therefore depending on the number of cpu
alternatives the size of the __alt_instructions array maybe odd, which
again also causes that the addresses of the nospec tables will be odd.
If the address of __nospec_call_start is odd and the kernel is compiled
With CONFIG_RELOCATABLE=n the compiler may generate code that loads the
address of __nospec_call_start with a 'larl' instruction.
This will generate incorrect code since the 'larl' instruction only works
with even addresses. In result the members of the nospec tables will be
accessed with an off-by-one offset, which subsequently may lead to
addressing exceptions within __nospec_revert().
The alignment check in prepare_hugepage_range() is wrong for 2 GB
hugepages, it only checks for 1 MB hugepage alignment.
This can result in kernel crash in __unmap_hugepage_range() at the
BUG_ON(start & ~huge_page_mask(h)) alignment check, for mappings
created with MAP_FIXED at unaligned address.
Fix this by correctly handling multiple hugepage sizes, similar to the
generic version of prepare_hugepage_range().
Fixes: d08de8e2d867 ("s390/mm: add support for 2GB hugepages") Cc: <stable@vger.kernel.org> # 4.8+ Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 1599069a62c6 ("phy: core: Warn when phy_power_on is called before
phy_init") the driver complains. In my case (Amlogic SoC) the warning
is: phy phy-fe03e000.phy.2: phy_power_on was called before phy_init
So change the order of the two calls. The same change has to be done
to the order of phy_exit() and phy_power_off().
Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.
According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.
For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:
dp->alt->vdo=0x140045
The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.
This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.
To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode") Cc: stable@vger.kernel.org Co-developed-by: Pablo Sun <pablo.sun@mediatek.com> Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com> Reviewed-by: Guillaume Ranquet <granquet@baylibre.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Pablo Sun <pablo.sun@mediatek.com> Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com> Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After xHC controller is started, either in probe or resume, it can take
a while before any of the connected usb devices are visible to the roothub
due to link training.
It's possible xhci driver loads, sees no acivity and suspends the host
before the USB device is visible.
In one testcase with a hotplugged xHC controller the host finally detected
the connected USB device and generated a wake 500ms after host initial
start.
If hosts didn't suspend the device duringe training it probablty wouldn't
take up to 500ms to detect it, but looking at specs reveal USB3 link
training has a couple long timeout values, such as 120ms
RxDetectQuietTimeout, and 360ms PollingLFPSTimeout.
So Add a 500ms grace period that keeps polling the roothub for 500ms after
start, preventing runtime suspend until USB devices are detected.
The reason for the warning is clear enough; the driver sends an
unusual read request on endpoint 0 but does not set the USB_DIR_IN bit
in the bRequestType field.
More importantly, the whole situation can be avoided and the driver
simplified by converting it over to the relatively new
usb_control_msg_recv() and usb_control_msg_send() routines. That's
what this fix does.
The received notification packet is held in pkg->buffer and not in pkg
itself. Fix this by using the correct buffer.
Fixes: 81a54b5e1986 ("thunderbolt: Let the connection manager handle all notifications") Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit 74a852479c68 ("xen-blkfront: add a parameter for disabling of persistent
grants") made a field of blkfront, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkfront saves
the parameter value in a separate place and advertises the support based
on only the saved value.
Fixes: 74a852479c68 ("xen-blkfront: add a parameter for disabling of persistent grants") Cc: <stable@vger.kernel.org> # 5.10.x Suggested-by: Juergen Gross <jgross@suse.com> Signed-off-by: SeongJae Park <sj@kernel.org> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220831165824.94815-3-sj@kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit aac8a70db24b ("xen-blkback: add a parameter for disabling of persistent
grants") made a field of blkback, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkback saves the
parameter value in a separate place and advertises the support based on
only the saved value.
Fixes: aac8a70db24b ("xen-blkback: add a parameter for disabling of persistent grants") Cc: <stable@vger.kernel.org> # 5.10.x Suggested-by: Juergen Gross <jgross@suse.com> Signed-off-by: SeongJae Park <sj@kernel.org> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20220831165824.94815-2-sj@kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mmap lock protects the page walker from changes to the page tables
during the walk. However a read lock is insufficient to protect those
areas which don't have a VMA as munmap() detaches the VMAs before
downgrading to a read lock and actually tearing down PTEs/page tables.
For users of walk_page_range() the solution is to simply call pte_hole()
immediately without checking the actual page tables when a VMA is not
present. We now never call __walk_page_range() without a valid vma.
For walk_page_range_novma() the locking requirements are tightened to
require the mmap write lock to be taken, and then walking the pgd
directly with 'no_vma' set.
This in turn means that all page walkers either have a valid vma, or
it's that special 'novma' case for page table debugging. As a result,
all the odd '(!walk->vma && !walk->no_vma)' tests can be removed.
Fixes: dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Steven Price <steven.price@arm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The change from kcalloc() to kvmalloc() means that arg->nr_pages
might now be large enough that the "args->nr_pages << PAGE_SHIFT" can
result in an integer overflow.
Fixes: b3f7931f5c61 ("xen/gntdev: switch from kcalloc() to kvcalloc()") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/YxDROJqu/RPvR0bi@kili Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
KVM should not claim to virtualize unknown IA32_ARCH_CAPABILITIES
bits. When kvm_get_arch_capabilities() was originally written, there
were only a few bits defined in this MSR, and KVM could virtualize all
of them. However, over the years, several bits have been defined that
KVM cannot just blindly pass through to the guest without additional
work (such as virtualizing an MSR promised by the
IA32_ARCH_CAPABILITES feature bit).
Define a mask of supported IA32_ARCH_CAPABILITIES bits, and mask off
any other bits that are set in the hardware MSR.
Cc: Paolo Bonzini <pbonzini@redhat.com> Fixes: 5b76a3cff011 ("KVM: VMX: Tell the nested hypervisor to skip L1D flush on vmentry") Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Vipin Sharma <vipinsh@google.com> Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Message-Id: <20220830174947.2182144-1-jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The regcache sync will set the cache_bypass = true, at that
time, when there is regmap write operation, it will bypass
the regmap cache, then the regcache sync will write back the
value from cache to register, which is not as our expectation.
Though regmap already use its internal lock to avoid such issue,
but this driver force disable the regmap internal lock in its
regmap config: disable_locking = true
To avoid this issue, use the driver's own lock to do the protect
in system PM.
The driver does not check if the cooling state passed to
gpio_fan_set_cur_state() exceeds the maximum cooling state as
stored in fan_data->num_speeds. Since the cooling state is later
used as an array index in set_fan_speed(), an array out of bounds
access can occur.
This can be exploited by setting the state of the thermal cooling device
to arbitrary values, causing for example a kernel oops when unavailable
memory is accessed this way.
The while loop in raspberrypi_discover_clocks() relies on the assumption
that the id of the last clock element is zero. Because this data comes
from the Videocore firmware and it doesn't guarantuee such a behavior
this could lead to out-of-bounds access. So fix this by providing
a sentinel element.
Fixes: 93d2725affd6 ("clk: bcm: rpi: Discover the firmware clocks") Link: https://github.com/raspberrypi/firmware/issues/1688 Suggested-by: Phil Elwell <phil@raspberrypi.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220713154953.3336-2-stefan.wahren@i2se.com Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Ivan T. Ivanov <iivanov@suse.de> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should have 'n', then 'size', not the opposite.
This is harmless because the 2 values are just multiplied, but having
the correct order silence a (unpublished yet) smatch warning.
The function raspberrypi_fw_get_rate (e.g. used for the recalc_rate
hook) can fail to get the clock rate from the firmware. In this case
we cannot return a signed error value, which would be casted to
unsigned long. Fix this by returning 0 instead.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220625083643.4012-1-stefan.wahren@i2se.com Fixes: 4e85e535e6cc ("clk: bcm283x: add driver interfacing with Raspberry Pi's firmware") Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the original commit 9a34b45397e5 ("clk: Add support for runtime PM"),
the commit message mentioned that pm_runtime_put_sync() would be done
at the end of clk_core_unprepare(). This mirrors the operations in
clk_core_prepare() in the opposite order.
However, the actual code that was added wasn't in the order the commit
message described. Move clk_pm_runtime_put() to the end of
clk_core_unprepare() so that it is in the correct order.
Fixes: 9a34b45397e5 ("clk: Add support for runtime PM") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20220822081424.1310926-3-wenst@chromium.org Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 35b0fac808b95eea1212f8860baf6ad25b88b087. Alexander
reports that it causes boot failures on i.MX8M Plus based boards
(specifically imx8mp-tqma8mpql-mba8mpxl.dts).
In the previous commits that added CLK_OPS_PARENT_ENABLE, support for
this flag was only added to rate change operations (rate setting and
reparent) and disabling unused subtree. It was not added to the
clock gate related operations. Any hardware driver that needs it for
these operations will either see bogus results, or worse, hang.
This has been seen on MT8192 and MT8195, where the imp_ii2_* clk
drivers set this, but dumping debugfs clk_summary would cause it
to hang.
Fixes: fc8726a2c021 ("clk: core: support clocks which requires parents enable (part 2)") Fixes: a4b3518d146f ("clk: core: support clocks which requires parents enable (part 1)") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Link: https://lore.kernel.org/r/20220822081424.1310926-2-wenst@chromium.org Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a spelling mistake in a gvt_vgpu_err error message. Fix it.
Fixes: 695fbc08d80f ("drm/i915/gvt: replace the gvt_err with gvt_vgpu_err") Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Signed-off-by: Zhi Wang <zhi.a.wang@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20220315202449.2952845-1-colin.i.king@gmail.com Reviewed-by: Zhi Wang <zhi.a.wang@intel.com> Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A transaction of type BINDER_TYPE_WEAK_HANDLE can fail to increment the
reference for a node. In this case, the target proc normally releases
the failed reference upon close as expected. However, if the target is
dying in parallel the call will race with binder_deferred_release(), so
the target could have released all of its references by now leaving the
cleanup of the new failed reference unhandled.
The transaction then ends and the target proc gets released making the
ref->proc now a dangling pointer. Later on, ref->node is closed and we
attempt to take spin_lock(&ref->proc->inner_lock), which leads to the
use-after-free bug reported below. Let's fix this by cleaning up the
failed reference on the spot instead of relying on the target to do so.
==================================================================
BUG: KASAN: use-after-free in _raw_spin_lock+0xa8/0x150
Write of size 4 at addr ffff5ca207094238 by task kworker/1:0/590
The probe session-duplication overflow check incremented the session
count also when there were no more available sessions so that memory
beyond the fixed-size slab-allocated session array could be corrupted in
fastrpc_session_alloc() on open().
Add the missing sanity check on the probed-session count to avoid
corrupting memory beyond the fixed-size slab-allocated session array
when there are more than FASTRPC_MAX_SESSIONS sessions defined in the
devicetree.
The ad7292 tries to add an devm_action for disabling a regulator at
device detach using devm_add_action_or_reset(). The
devm_add_action_or_reset() does call the release function should adding
action fail. The driver inspects the value returned by
devm_add_action_or_reset() and manually calls regulator_disable() if
adding the action has failed. This leads to double disable and messes
the enable count for regulator.
Do not manually call disable if devm_add_action_or_reset() fails.
Fixes: 506d2e317a0a ("iio: adc: Add driver support for AD7292") Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Tested-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com> Link: https://lore.kernel.org/r/Yv9O+9sxU7gAv3vM@fedora Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting hung task at __input_unregister_device() [1], for
iforce_close() waiting at wait_event_interruptible() with dev->mutex held
is blocking input_disconnect_device() from __input_unregister_device().
It seems that the cause is simply that commit c2b27ef672992a20 ("Input:
iforce - wait for command completion when closing the device") forgot to
call wake_up() after clear_bit().
Fix this problem by introducing a helper that calls clear_bit() followed
by wake_up_all().
Reported-by: syzbot <syzbot+deb6abc36aad4008f407@syzkaller.appspotmail.com> Fixes: c2b27ef672992a20 ("Input: iforce - wait for command completion when closing the device") Tested-by: syzbot <syzbot+deb6abc36aad4008f407@syzkaller.appspotmail.com> Suggested-by: Fabio M. De Francesco <fmdefrancesco@gmail.com> Co-developed-by: Hillf Danton <hdanton@sina.com> Signed-off-by: Hillf Danton <hdanton@sina.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Link: https://lore.kernel.org/r/887021c3-4f13-40ce-c8b9-aa6e09faa3a7@I-love.SAKURA.ne.jp Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the user initializes the uart port, and waits for the transmit
engine to complete in lpuart32_set_termios(), if the UART TX fifo has
dirty data and the UARTMODIR enable the flow control, the TX fifo may
never be empty. So here we should disable the flow control first to make
sure the transmit engin can complete.
When changing the console font with ioctl(KDFONTOP) the new font size
can be bigger than the previous font. A previous selection may thus now
be outside of the new screen size and thus trigger out-of-bounds
accesses to graphics memory if the selection is removed in
vc_do_resize().
Prevent such out-of-memory accesses by dropping the selection before the
various con_font_set() console handlers are called.
Christophe Leroy reported that commit 7b4537199a4a ("kbuild: link
symbol CRCs at final link, removing CONFIG_MODULE_REL_CRCS") broke
mpc85xx_defconfig + CONFIG_RELOCATABLE=y.
The compiler emits a bunch of R_PPC_UADDR32, which is not supported by
arch/powerpc/kernel/reloc_32.S.
The reason is there exists an unaligned symbol.
$ powerpc-linux-gnu-nm -n vmlinux
... c0b31258 d spe_aligninfo c0b31298 d __func__.0 c0b312a9 D sys_call_table c0b319b8 d __func__.0
Commit 7b4537199a4a is not the root cause. Even before that, I can
reproduce the same issue for mpc85xx_defconfig + CONFIG_RELOCATABLE=y
+ CONFIG_MODVERSIONS=n.
It is just that nobody noticed because when CONFIG_MODVERSIONS is
enabled, a __crc_* symbol inserted before sys_call_table was hiding the
unalignment issue.
Adding alignment to the syscall table for ppc32 fixes the issue.
projects / linux-stable / log