Currently, offloaded conntrack entries (flows) can only be deleted
after they are removed from offload, which is either by timeout,
tcp state change or tc ct rule deletion. This can cause issues for
users wishing to manually delete or flush existing entries.
Support deletion of offloaded conntrack entries.
Example usage:
# Delete all offloaded (and non offloaded) conntrack entries
# whose source address is 1.2.3.4
$ conntrack -D -s 1.2.3.4
# Delete all entries
$ conntrack -F
Signed-off-by: Paul Blakey <paulb@nvidia.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Acked-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Florian Westphal <fw@strlen.de> Cc: Demi Marie Obenour <demi@invisiblethingslab.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Schedutil normally calls the adjust_perf callback for drivers with
adjust_perf callback available and fast_switch_possible flag set.
However, when frequency invariance is disabled and schedutil tries to
invoke fast_switch. So, there is a chance of kernel crash if this
function pointer is not set. To protect against this scenario add
fast_switch callback to amd_pstate driver.
Fixes: 1d215f0319c2 ("cpufreq: amd-pstate: Add fast switch function for AMD P-State") Signed-off-by: Gautham R. Shenoy <gautham.shenoy@amd.com> Signed-off-by: Wyes Karny <wyes.karny@amd.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver should update policy->cur after updating the frequency.
Currently amd_pstate doesn't update policy->cur when `adjust_perf`
is used. Which causes /proc/cpuinfo to show wrong cpu frequency.
Fix this by updating policy->cur with correct frequency value in
adjust_perf function callback.
- Before the fix: (setting min freq to 1.5 MHz)
[root@amd]# cat /proc/cpuinfo | grep "cpu MHz" | sort | uniq --count
1 cpu MHz : 1777.016
1 cpu MHz : 1797.160
1 cpu MHz : 1797.270
189 cpu MHz : 400.000
- After the fix: (setting min freq to 1.5 MHz)
[root@amd]# cat /proc/cpuinfo | grep "cpu MHz" | sort | uniq --count
1 cpu MHz : 1753.353
1 cpu MHz : 1756.838
1 cpu MHz : 1776.466
1 cpu MHz : 1776.873
1 cpu MHz : 1777.308
1 cpu MHz : 1779.900
183 cpu MHz : 1805.231
1 cpu MHz : 1956.815
1 cpu MHz : 2246.203
1 cpu MHz : 2259.984
Fixes: 1d215f0319c2 ("cpufreq: amd-pstate: Add fast switch function for AMD P-State") Signed-off-by: Wyes Karny <wyes.karny@amd.com>
[ rjw: Subject edits ] Cc: 5.17+ <stable@vger.kernel.org> # 5.17+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, channel open messages were always sent to monitors on the first
ioctl() call for unbound HCI sockets, even if the command and arguments
were completely invalid. This can leave an exploitable hole with the abuse
of invalid ioctl calls.
This commit hardens the ioctl processing logic by first checking if the
command is valid, and immediately returning with an ENOIOCTLCMD error code
if it is not. This ensures that ioctl calls with invalid commands are free
of side effects, and increases the difficulty of further exploitation by
forcing exploitation to find a way to pass a valid command first.
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Co-developed-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Dragos-Marian Panait <dragos.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default the VSC8501 and VSC8502 RGMII/GMII/MII RX_CLK output is
disabled. To allow packet forwarding towards the MAC it needs to be
enabled.
For other PHYs supported by this driver the clock output is enabled
by default.
Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502") Signed-off-by: David Epping <david.epping@missinglinkelectronics.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
amd_pstate active mode driver is only compatible with static governors.
Therefore it doesn't need fast_switch functionality. Remove
fast_switch_possible flag from amd_pstate active mode driver.
Fixes: ffa5096a7c33 ("cpufreq: amd-pstate: implement Pstate EPP support for the AMD processors") Signed-off-by: Wyes Karny <wyes.karny@amd.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Check physical PFN is valid before converting the PFN to a struct page
pointer to be returned to caller of vfio_pin_pages().
vfio_pin_pages() pins user pages with contiguous IOVA.
If the IOVA of a user page to be pinned belongs to vma of vm_flags
VM_PFNMAP, pin_user_pages_remote() will return -EFAULT without returning
struct page address for this PFN. This is because usually this kind of PFN
(e.g. MMIO PFN) has no valid struct page address associated.
Upon this error, vaddr_get_pfns() will obtain the physical PFN directly.
While previously vfio_pin_pages() returns to caller PFN arrays directly,
after commit 34a255e67615 ("vfio: Replace phys_pfn with pages for vfio_pin_pages()"),
PFNs will be converted to "struct page *" unconditionally and therefore
the returned "struct page *" array may contain invalid struct page
addresses.
Given current in-tree users of vfio_pin_pages() only expect "struct page *
returned, check PFN validity and return -EINVAL to let the caller be
aware of IOVAs to be pinned containing PFN not able to be returned in
"struct page *" array. So that, the caller will not consume the returned
pointer (e.g. test PageReserved()) and avoid error like "supervisor read
access in kernel mode".
Fixes: 34a255e67615 ("vfio: Replace phys_pfn with pages for vfio_pin_pages()") Cc: Sean Christopherson <seanjc@google.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Yan Zhao <yan.y.zhao@intel.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Link: https://lore.kernel.org/r/20230519065843.10653-1-yan.y.zhao@intel.com Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If multiple CPUs are sharing the same hardware queue, it can
cause leak in the active queue counter tracking when __blk_mq_tag_busy()
is executed simultaneously.
Fixes: ee78ec1077d3 ("blk-mq: blk_mq_tag_busy is no need to return a value") Signed-off-by: Tian Lan <tian.lan@twosigma.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: John Garry <john.g.garry@oracle.com> Link: https://lore.kernel.org/r/20230522210555.794134-1-tilan7663@gmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b11d31ae01e6 ("blk-wbt: remove unnecessary check in
wbt_enable_default()") removes the checking of CONFIG_BLK_WBT_MQ by
mistake, which is used to control enable or disable wbt by default.
Fix the problem by adding back the checking. This patch also do a litter
cleanup to make related code more readable.
The read_skb() logic is incrementing the tcp->copied_seq which is used for
among other things calculating how many outstanding bytes can be read by
the application. This results in application errors, if the application
does an ioctl(FIONREAD) we return zero because this is calculated from
the copied_seq value.
To fix this we move tcp->copied_seq accounting into the recv handler so
that we update these when the recvmsg() hook is called and data is in
fact copied into user buffers. This gives an accurate FIONREAD value
as expected and improves ACK handling. Before we were calling the
tcp_rcv_space_adjust() which would update 'number of bytes copied to
user in last RTT' which is wrong for programs returning SK_PASS. The
bytes are only copied to the user when recvmsg is handled.
Doing the fix for recvmsg is straightforward, but fixing redirect and
SK_DROP pkts is a bit tricker. Build a tcp_psock_eat() helper and then
call this from skmsg handlers. This fixes another issue where a broken
socket with a BPF program doing a resubmit could hang the receiver. This
happened because although read_skb() consumed the skb through sock_drop()
it did not update the copied_seq. Now if a single reccv socket is
redirecting to many sockets (for example for lb) the receiver sk will be
hung even though we might expect it to continue. The hang comes from
not updating the copied_seq numbers and memory pressure resulting from
that.
We have a slight layer problem of calling tcp_eat_skb even if its not
a TCP socket. To fix we could refactor and create per type receiver
handlers. I decided this is more work than we want in the fix and we
already have some small tweaks depending on caller that use the
helper skb_bpf_strparser(). So we extend that a bit and always set
the strparser bit when it is in use and then we can gate the
seq_copied updates on this.
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230523025618.113937-9-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When TCP stack has data ready to read sk_data_ready() is called. Sockmap
overwrites this with its own handler to call into BPF verdict program.
But, the original TCP socket had sock_def_readable that would additionally
wake up any user space waiters with sk_wake_async().
Sockmap saved the callback when the socket was created so call the saved
data ready callback and then we can wake up any epoll() logic waiting
on the read.
Note we call on 'copied >= 0' to account for returning 0 when a FIN is
received because we need to wake up user for this as well so they
can do the recvmsg() -> 0 and detect the shutdown.
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230523025618.113937-8-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
A common mechanism to put a TCP socket into the sockmap is to hook the
BPF_SOCK_OPS_{ACTIVE_PASSIVE}_ESTABLISHED_CB event with a BPF program
that can map the socket info to the correct BPF verdict parser. When
the user adds the socket to the map the psock is created and the new
ops are assigned to ensure the verdict program will 'see' the sk_buffs
as they arrive.
Part of this process hooks the sk_data_ready op with a BPF specific
handler to wake up the BPF verdict program when data is ready to read.
The logic is simple enough (posted here for easy reading)
if (unlikely(!sock || !sock->ops || !sock->ops->read_skb))
return;
sock->ops->read_skb(sk, sk_psock_verdict_recv);
}
The oversight here is sk->sk_socket is not assigned until the application
accepts() the new socket. However, its entirely ok for the peer application
to do a connect() followed immediately by sends. The socket on the receiver
is sitting on the backlog queue of the listening socket until its accepted
and the data is queued up. If the peer never accepts the socket or is slow
it will eventually hit data limits and rate limit the session. But,
important for BPF sockmap hooks when this data is received TCP stack does
the sk_data_ready() call but the read_skb() for this data is never called
because sk_socket is missing. The data sits on the sk_receive_queue.
Then once the socket is accepted if we never receive more data from the
peer there will be no further sk_data_ready calls and all the data
is still on the sk_receive_queue(). Then user calls recvmsg after accept()
and for TCP sockets in sockmap we use the tcp_bpf_recvmsg_parser() handler.
The handler checks for data in the sk_msg ingress queue expecting that
the BPF program has already run from the sk_data_ready hook and enqueued
the data as needed. So we are stuck.
To fix do an unlikely check in recvmsg handler for data on the
sk_receive_queue and if it exists wake up data_ready. We have the sock
locked in both read_skb and recvmsg so should avoid having multiple
runners.
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230523025618.113937-7-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The sockmap code is returning EAGAIN after a FIN packet is received and no
more data is on the receive queue. Correct behavior is to return 0 to the
user and the user can then close the socket. The EAGAIN causes many apps
to retry which masks the problem. Eventually the socket is evicted from
the sockmap because its released from sockmap sock free handling. The
issue creates a delay and can cause some errors on application side.
To fix this check on sk_msg_recvmsg side if length is zero and FIN flag
is set then set return to zero. A selftest will be added to check this
condition.
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: William Findlay <will@isovalent.com> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230523025618.113937-6-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
We noticed some rare sk_buffs were stepping past the queue when system was
under memory pressure. The general theory is to skip enqueueing
sk_buffs when its not necessary which is the normal case with a system
that is properly provisioned for the task, no memory pressure and enough
cpu assigned.
But, if we can't allocate memory due to an ENOMEM error when enqueueing
the sk_buff into the sockmap receive queue we push it onto a delayed
workqueue to retry later. When a new sk_buff is received we then check
if that queue is empty. However, there is a problem with simply checking
the queue length. When a sk_buff is being processed from the ingress queue
but not yet on the sockmap msg receive queue its possible to also recv
a sk_buff through normal path. It will check the ingress queue which is
zero and then skip ahead of the pkt being processed.
Previously we used sock lock from both contexts which made the problem
harder to hit, but not impossible.
To fix instead of popping the skb from the queue entirely we peek the
skb from the queue and do the copy there. This ensures checks to the
queue length are non-zero while skb is being processed. Then finally
when the entire skb has been copied to user space queue or another
socket we pop it off the queue. This way the queue length check allows
bypassing the queue only after the list has been completely processed.
To reproduce issue we run NGINX compliance test with sockmap running and
observe some flakes in our testing that we attributed to this issue.
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()") Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: William Findlay <will@isovalent.com> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230523025618.113937-5-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Now that the backlog manages the reschedule() logic correctly we can drop
the partial fix to reschedule from recvmsg hook.
Rescheduling on recvmsg hook was added to address a corner case where we
still had data in the backlog state but had nothing to kick it and
reschedule the backlog worker to run and finish copying data out of the
state. This had a couple limitations, first it required user space to
kick it introducing an unnecessary EBUSY and retry. Second it only
handled the ingress case and egress redirects would still be hung.
With the correct fix, pushing the reschedule logic down to where the
enomem error occurs we can drop this fix.
Fixes: bec217197b412 ("skmsg: Schedule psock work if the cached skb exists on the psock") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230523025618.113937-4-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Sk_buffs are fed into sockmap verdict programs either from a strparser
(when the user might want to decide how framing of skb is done by attaching
another parser program) or directly through tcp_read_sock. The
tcp_read_sock is the preferred method for performance when the BPF logic is
a stream parser.
The flow for Cilium's common use case with a stream parser is,
tcp_read_sock()
sk_psock_verdict_recv
ret = bpf_prog_run_pin_on_cpu()
sk_psock_verdict_apply(sock, skb, ret)
// if system is under memory pressure or app is slow we may
// need to queue skb. Do this queuing through ingress_skb and
// then kick timer to wake up handler
skb_queue_tail(ingress_skb, skb)
schedule_work(work);
The work queue is wired up to sk_psock_backlog(). This will then walk the
ingress_skb skb list that holds our sk_buffs that could not be handled,
but should be OK to run at some later point. However, its possible that
the workqueue doing this work still hits an error when sending the skb.
When this happens the skbuff is requeued on a temporary 'state' struct
kept with the workqueue. This is necessary because its possible to
partially send an skbuff before hitting an error and we need to know how
and where to restart when the workqueue runs next.
Now for the trouble, we don't rekick the workqueue. This can cause a
stall where the skbuff we just cached on the state variable might never
be sent. This happens when its the last packet in a flow and no further
packets come along that would cause the system to kick the workqueue from
that side.
To fix we could do simple schedule_work(), but while under memory pressure
it makes sense to back off some instead of continue to retry repeatedly. So
instead to fix convert schedule_work to schedule_delayed_work and add
backoff logic to reschedule from backlog queue on errors. Its not obvious
though what a good backoff is so use '1'.
To test we observed some flakes whil running NGINX compliance test with
sockmap we attributed these failed test to this bug and subsequent issue.
>From on list discussion. This commit
bec217197b41("skmsg: Schedule psock work if the cached skb exists on the psock")
was intended to address similar race, but had a couple cases it missed.
Most obvious it only accounted for receiving traffic on the local socket
so if redirecting into another socket we could still get an sk_buff stuck
here. Next it missed the case where copied=0 in the recv() handler and
then we wouldn't kick the scheduler. Also its sub-optimal to require
userspace to kick the internal mechanisms of sockmap to wake it up and
copy data to user. It results in an extra syscall and requires the app
to actual handle the EAGAIN correctly.
Fixes: 04919bed948dc ("tcp: Introduce tcp_read_skb()") Signed-off-by: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: William Findlay <will@isovalent.com> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Link: https://lore.kernel.org/bpf/20230523025618.113937-3-john.fastabend@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The read_skb hook calls consume_skb() now, but this means that if the
recv_actor program wants to use the skb it needs to inc the ref cnt
so that the consume_skb() doesn't kfree the sk_buff.
This is problematic because in some error cases under memory pressure
we may need to linearize the sk_buff from sk_psock_skb_ingress_enqueue().
Then we get this,
Because we incremented users refcnt from sk_psock_verdict_recv() we
hit the bug on with refcnt > 1 and trip it.
To fix lets simply pass ownership of the sk_buff through the skb_read
call. Then we can drop the consume from read_skb handlers and assume
the verdict recv does any required kfree.
Bug found while testing in our CI which runs in VMs that hit memory
constraints rather regularly. William tested TCP read_skb handlers.
In fact the device with chip id 0xD283 is called NCT6126D, and that is
the chip id the Nuvoton code was written for. Correct that name to avoid
confusion, because a NCT6116D in fact exists as well but has another
chip id, and is currently not supported.
The look at the spec also revealed that GPIO group7 in fact has 8 pins,
so correct the pin count in that group as well.
Fixes: d0918a84aff0 ("gpio-f7188x: Add GPIO support for Nuvoton NCT6116") Reported-by: Xing Tong Wu <xingtong.wu@siemens.com> Signed-off-by: Henning Schild <henning.schild@siemens.com> Acked-by: Simon Guinot <simon.guinot@sequanux.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
devcom events are sent to all registered component. Following the
cited patch, it is possible for two components, e.g.: two eswitches,
to send devcom events, while both components are registered. This
means eswitch layer will do double un/pairing, which is double
allocation and free of resources, even though only one un/pairing is
needed. flow example:
This reverts commit 606e6a72e29dff9e3341c4cc9b554420e4793f401 which exposes
the vnic diagnostic counters via debugfs. Instead, The upcoming series will
expose the same counters through devlink health reporter.
This reverts commit 4fe1b3a5f8fe2fdcedcaba9561e5b0ae5cb1d15b, which
exposes the steering dropped packets counter via debugfs. The upcoming
series will expose the counter via devlink health reporter instead
of debugfs.
[ 826.534521] The buggy address belongs to the object at ffff888194485800
which belongs to the cache kmalloc-512 of size 512
[ 826.535506] The buggy address is located 48 bytes inside of
freed 512-byte region [ffff888194485800, ffff888194485a00)
[ 826.541095] Memory state around the buggy address:
[ 826.541519] ffff888194485700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 826.542149] ffff888194485780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 826.542773] >ffff888194485800: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 826.543400] ^
[ 826.543822] ffff888194485880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 826.544452] ffff888194485900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 826.545079] ==================================================================
Fixes: 6702782845a5 ("net/mlx5e: TC, Set CT miss to the specific ct action instance") Signed-off-by: Paul Blakey <paulb@nvidia.com> Reviewed-by: Vlad Buslov <vladbu@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For a bigjoiner configuration display->crtc_disable() will be called
first for the slave CRTCs and then for the master CRTC. However slave
CRTCs will be actually disabled only after the master CRTC is disabled
(from the encoder disable hooks called with the master CRTC state).
Hence the slave PIPEDMCs can be disabled only after the master CRTC is
disabled, make this so.
intel_encoders_post_pll_disable() must be called only for the master
CRTC, as for the other two encoder disable hooks. While at it fix this
up as well. This didn't cause a problem, since
intel_encoders_post_pll_disable() will call the corresponding hook only
for an encoder/connector connected to the given CRTC, however slave
CRTCs will have no associated encoder/connector.
Fixes: 3af2ff0840be ("drm/i915: Enable a PIPEDMC whenever its corresponding pipe is enabled") Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Imre Deak <imre.deak@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230510103131.1618266-2-imre.deak@intel.com
(cherry picked from commit 7eeef32719f6af935a1554813e6bc206446339cd) Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bspec requires disabling the DPLLs on TC ports before disconnecting the
port's PHY. Add a post_pll_disable encoder hook and move the call to
disconnect the port's PHY from the post_disable hook to the new hook.
The spec requires disabling the PLL on TC ports before disconnecting the
port's PHY. Prepare for that by moving the PLL disabling to the CRTC
disable hook, while disconnecting the PHY will be moved to the
post_pll_disable() encoder hook in the next patch.
v2: Move the call from intel_crtc_disable_noatomic() as well.
When changing value of kcontrol, FW module to which data should be send
needs to be found. Currently it is done in improper way, fix it. Change
function name to indicate that it looks only for volume module.
This allows to change volume during runtime, instead of only changing
init value.
Fixes: be2b81b519d7 ("ASoC: Intel: avs: Parse control tuples") Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com> Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com> Link: https://lore.kernel.org/r/20230519201711.4073845-2-amadeuszx.slawinski@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In devm_cxl_add_port() the port creation may fail and its associated
pointer does not contain a valid address. During error message
generation this invalid port address is used. Fix that wrong address
access.
Fixes: f3cd264c4ec1 ("cxl: Unify debug messages when calling devm_cxl_add_port()") Signed-off-by: Robert Richter <rrichter@amd.com> Reviewed-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/20230519215436.3394532-1-rrichter@amd.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Two dma_wmb() are added in the XDP TX path to ensure proper ordering of
descriptor and buffer updates:
1. A dma_wmb() is added after updating the last BD to make sure
the updates to rest of the descriptor are visible before
transferring ownership to FEC.
2. A dma_wmb() is also added after updating the bdp to ensure these
updates are visible before updating txq->bd.cur.
3. Start the xmit of the frame immediately right after configuring the
tx descriptor.
Fixes: 6d6b39f180b8 ("net: fec: add initial XDP support") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Reviewed-by: Wei Fang <wei.fang@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When receive buffer is small, or the TCP rx queue looks too
complicated to bother using it directly - we allocate a new
skb and copy data into it.
We already use sk->sk_allocation... but nothing actually
sets it to GFP_ATOMIC on the ->sk_data_ready() path.
Users of HW offload are far more likely to experience problems
due to scheduling while atomic. "Copy mode" is very rarely
triggered with SW crypto.
Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser") Tested-by: Shai Amiram <samiram@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When receive buffer is small we try to copy out the data from
TCP into a skb maintained by TLS to prevent connection from
stalling. Unfortunately if a single record is made up of a mix
of decrypted and non-decrypted skbs combining them into a single
skb leads to loss of decryption status, resulting in decryption
errors or data corruption.
Similarly when trying to use TCP receive queue directly we need
to make sure that all the skbs within the record have the same
status. If we don't the mixed status will be detected correctly
but we'll CoW the anchor, again collapsing it into a single paged
skb without decrypted status preserved. So the "fixup" code will
not know which parts of skb to re-encrypt.
Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser") Tested-by: Shai Amiram <samiram@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We'll need to copy input skbs individually in the next patch.
Factor that code out (without assuming we're copying a full record).
Tested-by: Shai Amiram <samiram@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: eca9bfafee3a ("tls: rx: strp: preserve decryption status of skbs when needed") Signed-off-by: Sasha Levin <sashal@kernel.org>
If a record is partially decrypted we'll have to CoW it, anyway,
so go into copy mode and allocate a writable skb right away.
This will make subsequent fix simpler because we won't have to
teach tls_strp_msg_make_copy() how to copy skbs while preserving
decrypt status.
Tested-by: Shai Amiram <samiram@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: eca9bfafee3a ("tls: rx: strp: preserve decryption status of skbs when needed") Signed-off-by: Sasha Levin <sashal@kernel.org>
We call tls_rx_msg_size(skb) before doing skb->len += chunk.
So the tls_rx_msg_size() code will see old skb->len, most
likely leading to an over-read.
Worst case we will over read an entire record, next iteration
will try to trim the skb but may end up turning frag len negative
or discarding the subsequent record (since we already told TCP
we've read it during previous read but now we'll trim it out of
the skb).
Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser") Tested-by: Shai Amiram <samiram@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
alloc_skb_with_frags() fills in page frag sizes but does not
set skb->len and skb->data_len. Set those correctly otherwise
device offload will most likely generate an empty skb and
hit the BUG() at the end of __skb_nsg().
Fixes: 84c61fe1a75b ("tls: rx: do not use the standard strparser") Tested-by: Shai Amiram <samiram@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
skb->len covers the entire skb, including the frag_list.
In fact we're guaranteed that rxm->full_len <= skb->len,
so since the change under Fixes we were not checking decrypt
status of any skb but the first.
Note that the skb_pagelen() added here may feel a bit costly,
but it's removed by subsequent fixes, anyway.
Reported-by: Tariq Toukan <tariqt@nvidia.com> Fixes: 86b259f6f888 ("tls: rx: device: bound the frag walk") Tested-by: Shai Amiram <samiram@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If static allocation and dynamic allocation GPIOs are present,
dynamic allocation pollutes the numberspace for static allocation,
causing static allocation to fail.
Enforce dynamic allocation above GPIO_DYNAMIC_BASE.
Seen on a GTA04 when omap-gpio (static) and twl-gpio (dynamic)
raced:
[some successful registrations of omap_gpio instances]
[ 2.553833] twl4030_gpio twl4030-gpio: gpio (irq 145) chaining IRQs 161..178
[ 2.561401] gpiochip_find_base: found new base at 160
[ 2.564392] gpio gpiochip5: (twl4030): added GPIO chardev (254:5)
[ 2.564544] gpio gpiochip5: registered GPIOs 160 to 177 on twl4030
[...]
[ 2.692169] omap-gpmc 6e000000.gpmc: GPMC revision 5.0
[ 2.697357] gpmc_mem_init: disabling cs 0 mapped at 0x0-0x1000000
[ 2.703643] gpiochip_find_base: found new base at 178
[ 2.704376] gpio gpiochip6: (omap-gpmc): added GPIO chardev (254:6)
[ 2.704589] gpio gpiochip6: registered GPIOs 178 to 181 on omap-gpmc
[...]
[ 2.840393] gpio gpiochip7: Static allocation of GPIO base is deprecated, use dynamic allocation.
[ 2.849365] gpio gpiochip7: (gpio-160-191): GPIO integer space overlap, cannot add chip
[ 2.857513] gpiochip_add_data_with_key: GPIOs 160..191 (gpio-160-191) failed to register, -16
[ 2.866149] omap_gpio 48310000.gpio: error -EBUSY: Could not register gpio chip
On that device it is fixed invasively by
commit 92bf78b33b0b4 ("gpio: omap: use dynamic allocation of base")
but let's also fix that for devices where there is still
a mixture of static and dynamic allocation.
Fixes: 7b61212f2a07 ("gpiolib: Get rid of ARCH_NR_GPIOS") Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Reviewed-by: <christophe.leroy@csgroup.eu> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is because the DRAM address used for accessing metrics table
needs to be refreshed after a suspend resume cycle. Add a resume
callback to reset this again.
Fixes: 1a409b35c995 ("platform/x86/amd/pmf: Get performance metrics from PMFW") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20230513011408.958-1-mario.limonciello@amd.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to Renesas Electronics (formerly Dialog Semiconductor), the
standard AUTO mode of the PMIC DA9061 can lead to stability problems
depending on the hardware revision. It is recommended to set a defined
mode such as PFM or PWM permanently. So set and limit the mode for
buck 1, 2 and 3 to a fixed one.
Fixes: 611b6c891e40 ("ARM: dts: imx6ull-dhcom: Add DH electronics DHCOM i.MX6ULL SoM and PDK2 board") Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Reviewed-by: Marek Vasut <marex@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Spi geni driver switches between FIFO and DMA modes based on xfer length.
FIFO mode relies on M_CMD_DONE_EN interrupt for completion while DMA mode
relies on XX_DMA_DONE.
During dynamic switching, if FIFO mode is chosen, FIFO related interrupts
are enabled and DMA related interrupts are disabled. And viceversa.
Chip select shares M_CMD_DONE_EN interrupt with FIFO to check completion.
Now, if a chip select operation is preceded by a DMA xfer, M_CMD_DONE_EN
interrupt would have been disabled and hence it will never receive one
resulting in timeout.
For chip select, in addition to setting the xfer mode to FIFO,
select_mode() to FIFO so that required interrupts are enabled.
Fixes: e5f0dfa78ac7 ("spi: spi-geni-qcom: Add support for SE DMA mode") Suggested-by: Praveen Talari <quic_ptalari@quicinc.com Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com Reviewed-by: Douglas Anderson <dianders@chromium.org Link: https://lore.kernel.org/r/1683626496-9685-1-git-send-email-quic_vnivarth@quicinc.com Signed-off-by: Mark Brown <broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit bb1be7498500 ("firmware: arm_ffa: Add v1.1 get_partition_info support")
adds support to discovery the UUIDs of the partitions or just fetch the
partition count using the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag.
However the commit doesn't handle the fact that the older version doesn't
understand the flag and must be MBZ which results in firmware returning
invalid parameter error. That results in the failure of the driver probe
which is in correct.
Limit the usage of the PARTITION_INFO_GET_RETURN_COUNT_ONLY flag for the
versions above v1.0(i.e v1.1 and onwards) which fixes the issue.
scmi_xfer_raw_worker_init() is specifying a flag, WQ_SYSFS, as @max_active.
Fix it by or'ing WQ_SYSFS into @flags so that it actually enables sysfs
interface and using 0 for @max_active for the default setting.
Marc writes:
can you please revert this patch, without the corresponding driver patch
[1] it breaks probing of the device, as no one populates the sub-nodes.
[1] 9cb6d1b39a8f ("soc: imx: imx8m-blk-ctrl: Scan subnodes and bind
drivers to them")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://lore.kernel.org/r/20230523-justly-situated-317e792f4c1b-mkl@pengutronix.de Cc: Alexander Stein <alexander.stein@ew.tq-group.com> Cc: Liu Ying <victor.liu@nxp.com> Cc: Alexander Stein <alexander.stein@ew.tq-group.com> Cc: Marek Vasut <marex@denx.de> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mscc driver implements support for VSC8502, so its ID should be in
the MODULE_DEVICE_TABLE for automatic loading.
Signed-off-by: David Epping <david.epping@missinglinkelectronics.com> Fixes: d3169863310d ("net: phy: mscc: add support for VSC8502") Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit c6d96df9fa2c ("net: ethernet: mtk_eth_soc: drop generic vlan rx
offload, only use DSA untagging") makes VLAN RX offloading to be only used
on the SoCs without the MTK_NETSYS_V2 ability (which are not just MT7621
and MT7622). The commit disables the proper handling of special tagged
(DSA) frames, added with commit 87e3df4961f4 ("net-next: ethernet:
mediatek: add CDM able to recognize the tag for DSA"), for non
MTK_NETSYS_V2 SoCs when it finds a MAC that does not use DSA. So if the
other MAC uses DSA, the CDMQ component transmits DSA tagged frames to the
CPU improperly. This issue can be observed on frames with TCP, for example,
a TCP speed test using iperf3 won't work.
The commit disables the proper handling of special tagged (DSA) frames
because it assumes that these SoCs don't use more than one MAC, which is
wrong. Although I made Frank address this false assumption on the patch log
when they sent the patch on behalf of Felix, the code still made changes
with this assumption.
Therefore, the proper handling of special tagged (DSA) frames must be kept
enabled in all circumstances as it doesn't affect non DSA tagged frames.
Hardware DSA untagging, introduced with the commit 2d7605a72906 ("net:
ethernet: mtk_eth_soc: enable hardware DSA untagging"), and VLAN RX
offloading are operations on the two CDM components of the frame engine,
CDMP and CDMQ, which connect to Packet DMA (PDMA) and QoS DMA (QDMA) and
are between the MACs and the CPU. These operations apply to all MACs of the
SoC so if one MAC uses DSA and the other doesn't, the hardware DSA
untagging operation will cause the CDMP component to transmit non DSA
tagged frames to the CPU improperly.
Since the VLAN RX offloading feature configuration was dropped, VLAN RX
offloading can only be used along with hardware DSA untagging. So, for the
case above, we need to disable both features and leave it to the CPU,
therefore software, to untag the DSA and VLAN tags.
So the correct way to handle this is:
For all SoCs:
Enable the proper handling of special tagged (DSA) frames
(MTK_CDMQ_IG_CTRL).
Fixes: c6d96df9fa2c ("net: ethernet: mtk_eth_soc: drop generic vlan rx offload, only use DSA untagging") Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
page_pool_ring_[un]lock() use in_softirq() to decide which
spin lock variant to use, and when they are called in the
context with in_softirq() being false, spin_lock_bh() is
called in page_pool_ring_lock() while spin_unlock() is
called in page_pool_ring_unlock(), because spin_lock_bh()
has disabled the softirq in page_pool_ring_lock(), which
causes inconsistency for spin lock pair calling.
This patch fixes it by returning in_softirq state from
page_pool_producer_lock(), and use it to decide which
spin lock variant to use in page_pool_producer_unlock().
As pool->ring has both producer and consumer lock, so
rename it to page_pool_producer_[un]lock() to reflect
the actual usage. Also move them to page_pool.c as they
are only used there, and remove the 'inline' as the
compiler may have better idea to do inlining or not.
Fixes: 7886244736a4 ("net: page_pool: Add bulk support for ptr_ring") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Acked-by: Jesper Dangaard Brouer <brouer@redhat.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Link: https://lore.kernel.org/r/20230522031714.5089-1-linyunsheng@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the CLC handshake, server sequentially tries available SMCRv2
and SMCRv1 devices in smc_listen_work().
If an SMCRv2 device is found. SMCv2 based link group and link will be
assigned to the connection. Then assumed that some buffer assignment
errors happen later in the CLC handshake, such as RMB registration
failure, server will give up SMCRv2 and try SMCRv1 device instead. But
the resources assigned to the connection won't be reset.
When server tries SMCRv1 device, the connection creation process will
be executed again. Since conn->lnk has been assigned when trying SMCRv2,
it will not be set to the correct SMCRv1 link in
smcr_lgr_conn_assign_link(). So in such situation, conn->lgr points to
correct SMCRv1 link group but conn->lnk points to the SMCRv2 link
mistakenly.
Then in smc_clc_send_confirm_accept(), conn->rmb_desc->mr[link->link_idx]
will be accessed. Since the link->link_idx is not correct, the related
MR may not have been initialized, so crash happens.
| Try SMCRv2 device first
| |-> conn->lgr: assign existed SMCRv2 link group;
| |-> conn->link: assign existed SMCRv2 link (link_idx may be 1 in SMC_LGR_SYMMETRIC);
| |-> sndbuf & RMB creation fails, quit;
|
| Try SMCRv1 device then
| |-> conn->lgr: create SMCRv1 link group and assign;
| |-> conn->link: keep SMCRv2 link mistakenly;
| |-> sndbuf & RMB creation succeed, only RMB->mr[link_idx = 0]
| initialized.
|
| Then smc_clc_send_confirm_accept() accesses
| conn->rmb_desc->mr[conn->link->link_idx, which is 1], then crash.
v
This patch tries to fix this by cleaning conn->lnk before assigning
link. In addition, it is better to reset the connection and clean the
resources assigned if trying SMCRv2 failed in buffer creation or
registration.
Fixes: e49300a6bf62 ("net/smc: add listen processing for SMC-Rv2") Link: https://lore.kernel.org/r/20220523055056.2078994-1-liuyacan@corp.netease.com/ Signed-off-by: Wen Gu <guwen@linux.alibaba.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sen Chu <sen.chu@mediatek.com Fixes: 4cfc96547512 ("regulator: mt6359: Add support for MT6359P regulator") Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com Link: https://lore.kernel.org/r/20230518040646.8730-1-sen.chu@mediatek.com Signed-off-by: Mark Brown <broonie@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transmit buffers allocated by the driver can be used to transmit data
by any messages/commands needing the buffer. However, it is not guaranteed
to have been zero-ed before every new transmission and hence it will just
contain residual value from the previous transmission. There are several
reserved fields in the memory descriptors that must be zero(MBZ). The
receiver can reject the transmission if any such MBZ fields are non-zero.
While we can set the whole page to zero, it is not optimal as most of the
fields get initialised to the value required for the current transmission.
So, just set the reserved/MBZ fields to zero in the memory descriptors
explicitly to honour the requirement and keep the receiver happy.
Fixes: cc2195fe536c ("firmware: arm_ffa: Add support for MEM_* interfaces") Reported-by: Marc Bonnici <marc.bonnici@arm.com> Link: https://lore.kernel.org/r/20230503131252.12585-1-sudeep.holla@arm.com Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing the ethernet interface on a Variscite symphony carrier
board using an imx8mn SOM with an onboard ADIN1300 PHY (EC hardware
configuration), the ethernet PHY is not detected.
The ADIN1300 datasheet indicate that the "Management interface
active (t4)" state is reached at most 5ms after the reset signal is
deasserted.
The device tree in Variscite custom git repository uses the following
property:
phy-reset-post-delay = <20>;
Add a new MDIO property 'reset-deassert-us' of 20ms to have the same
delay inside the ethphy node. Adding this property fixes the problem
with the PHY detection.
Note that this SOM can also have an Atheros AR8033 PHY. In this case,
a 1ms deassert delay is sufficient. Add a comment to that effect.
Fixes: ade0176dd8a0 ("arm64: dts: imx8mn-var-som: Add Variscite VAR-SOM-MX8MN System on Module") Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From one hand, mlx5 driver is allowing to probe PFs in parallel.
From the other hand, devcom, which is a share resource between PFs, is
registered without any lock. This might resulted in memory problems.
Hence, use the global mlx5_dev_list_lock in order to serialize devcom
registration.
In case devcom allocation is failed, mlx5 is always freeing the priv.
However, this priv might have been allocated by a different thread,
and freeing it might lead to use-after-free bugs.
Fix it by freeing the priv only in case it was allocated by the
running thread.
DEVX can issue a general command, which is not used by mlx5 driver.
In case such command is failed, mlx5 is trying to collect the failure
data, However, mlx5 doesn't create a storage for this command, since
mlx5 doesn't use it. This lead to array-index-out-of-bounds error.
Fix it by checking whether the command is known before collecting the
failure data.
SW Steering uses RC QP for writing STEs to ICM. This writingis done in LB
(loopback), and FL (force-loopback) QP is preferred for performance. FL is
available when RoCE is enabled or disabled based on RoCE caps.
This patch adds reading of FL capability from HCA caps in addition to the
existing reading from RoCE caps, thus fixing the case where we didn't
have loopback enabled when RoCE was disabled.
In case user switch a device from switchdev mode to legacy mode, mlx5
first unpair the E-switch and afterwards unload the uplink vport.
From the other hand, in case user remove or reload a device, mlx5
first unload the uplink vport and afterwards unpair the E-switch.
The latter is causing a bug[1], hence, handle pairing of E-switch as
part of uplink un/load APIs.
[1]
In case VF_LAG is used, every tc fdb flow is duplicated to the peer
esw. However, the original esw keeps a pointer to this duplicated
flow, not the peer esw.
e.g.: if user create tc fdb flow over esw0, the flow is duplicated
over esw1, in FW/HW, but in SW, esw0 keeps a pointer to the duplicated
flow.
During module unload while a peer tc fdb flow is still offloaded, in
case the first device to be removed is the peer device (esw1 in the
example above), the peer net-dev is destroyed, and so the mlx5e_priv
is memset to 0.
Afterwards, the peer device is trying to unpair himself from the
original device (esw0 in the example above). Unpair API invoke the
original device to clear peer flow from its eswitch (esw0), but the
peer flow, which is stored over the original eswitch (esw0), is
trying to use the peer mlx5e_priv, which is memset to 0 and result in
bellow kernel-oops.
When calculating crc for hash index we use the function crc32 that
calculates for little-endian (LE) arch.
Then we convert it to network endianness using htonl(), but it's wrong
to do the conversion in BE archs since the crc32 value is already LE.
The solution is to switch the bytes from the crc result for all types
of arc.
Fixes: 40416d8ede65 ("net/mlx5: DR, Replace CRC32 implementation to use kernel lib") Signed-off-by: Erez Shitrit <erezsh@nvidia.com> Reviewed-by: Alex Vesker <valex@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NAPI gets called with budget of 0 from netpoll, which has interrupts
disabled. We should try to free some space on Tx rings and nothing
else.
Specifically do not try to handle XDP TX or try to refill Rx buffers -
we can't use the page pool from IRQ context. Don't check if IRQs moved,
either, that makes no sense in netpoll. Netpoll calls _all_ the rings
from whatever CPU it happens to be invoked on.
In general do as little as possible, the work quickly adds up when
there's tens of rings to poll.
AFAIU page pool takes a BH lock, releases it and since BH is now
enabled tries to run softirqs.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Fixes: 60bbf7eeef10 ("mlx5: use page_pool for xdp_return_frame call") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With introduction of post action infrastructure most of the users of encap
attribute had been modified in order to obtain the correct attribute by
calling mlx5e_tc_get_encap_attr() helper instead of assuming encap action
is always on default attribute. However, the cited commit didn't modify
mlx5e_invalidate_encap() which prevents it from destroying correct modify
header action which leads to a warning [0]. Fix the issue by using correct
attribute.
[0]:
Feb 21 09:47:35 c-237-177-40-045 kernel: WARNING: CPU: 17 PID: 654 at drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:684 mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: RIP: 0010:mlx5e_tc_attach_mod_hdr+0x1cc/0x230 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: Call Trace:
Feb 21 09:47:35 c-237-177-40-045 kernel: <TASK>
Feb 21 09:47:35 c-237-177-40-045 kernel: mlx5e_tc_fib_event_work+0x8e3/0x1f60 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? mlx5e_take_all_encap_flows+0xe0/0xe0 [mlx5_core]
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lock_downgrade+0x6d0/0x6d0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x273/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: process_one_work+0x7c2/0x1310
Feb 21 09:47:35 c-237-177-40-045 kernel: ? lockdep_hardirqs_on_prepare+0x3f0/0x3f0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? pwq_dec_nr_in_flight+0x230/0x230
Feb 21 09:47:35 c-237-177-40-045 kernel: ? rwlock_bug.part.0+0x90/0x90
Feb 21 09:47:35 c-237-177-40-045 kernel: worker_thread+0x59d/0xec0
Feb 21 09:47:35 c-237-177-40-045 kernel: ? __kthread_parkme+0xd9/0x1d0
Fixes: 8300f225268b ("net/mlx5e: Create new flow attr for multi table actions") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cited commit causes ABBA deadlock[0] when peer flows are created while
holding the devcom rw semaphore. Due to peer flows offload implementation
the lock is taken much higher up the call chain and there is no obvious way
to easily fix the deadlock. Instead, since tc route query code needs the
peer eswitch structure only to perform a lookup in xarray and doesn't
perform any sleeping operations with it, refactor the code for lockless
execution in following ways:
- RCUify the devcom 'data' pointer. When resetting the pointer
synchronously wait for RCU grace period before returning. This is fine
since devcom is currently only used for synchronization of
pairing/unpairing of eswitches which is rare and already expensive as-is.
- Wrap all usages of 'paired' boolean in {READ|WRITE}_ONCE(). The flag has
already been used in some unlocked contexts without proper
annotations (e.g. users of mlx5_devcom_is_paired() function), but it wasn't
an issue since all relevant code paths checked it again after obtaining the
devcom semaphore. Now it is also used by mlx5_devcom_get_peer_data_rcu() as
"best effort" check to return NULL when devcom is being unpaired. Note that
while RCU read lock doesn't prevent the unpaired flag from being changed
concurrently it still guarantees that reader can continue to use 'data'.
- Refactor mlx5e_tc_query_route_vport() function to use new
mlx5_devcom_get_peer_data_rcu() API which fixes the deadlock.
[0]:
[ 164.599612] ======================================================
[ 164.600142] WARNING: possible circular locking dependency detected
[ 164.600667] 6.3.0-rc3+ #1 Not tainted
[ 164.601021] ------------------------------------------------------
[ 164.601557] handler1/3456 is trying to acquire lock:
[ 164.601998] ffff88811f1714b0 (&esw->offloads.encap_tbl_lock){+.+.}-{3:3}, at: mlx5e_attach_encap+0xd8/0x8b0 [mlx5_core]
[ 164.603078]
but task is already holding lock:
[ 164.603617] ffff88810137fc98 (&comp->sem){++++}-{3:3}, at: mlx5_devcom_get_peer_data+0x37/0x80 [mlx5_core]
[ 164.604459]
which lock already depends on the new lock.
Check in the mlx5e_ptp_poll_ts_cq context if the ptp tx sq should be woken
up. Before change, the ptp tx sq may never wake up if the ptp tx ts skb
fifo is full when mlx5e_poll_tx_cq checks if the queue should be woken up.
When doing plpmtu probe, the probe size is growing every time when it
receives the ACK during the Search state until the probe fails. When
the failure occurs, pl.probe_high is set and it goes to the Complete
state.
However, if the link pmtu is huge, like 65535 in loopback_dev, the probe
eventually keeps using SCTP_MAX_PLPMTU as the probe size and never fails.
Because of that, pl.probe_high can not be set, and the plpmtu probe can
never go to the Complete state.
Fix it by setting pl.probe_high to SCTP_MAX_PLPMTU when the probe size
grows to SCTP_MAX_PLPMTU in sctp_transport_pl_recv(). Also, not allow
the probe size greater than SCTP_MAX_PLPMTU in the Complete state.
Fixes: b87641aff9e7 ("sctp: do state transition when a probe succeeds on HB ACK recv path") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move cxl_await_media_ready() to cxl_pci probe before driver starts issuing
IDENTIFY and retrieving memory device information to ensure that the
device is ready to provide the information. Allow cxl_pci_probe() to succeed
even if media is not ready. Cache the media failure in cxlds and don't ask
the device for any media information.
The rationale for proceeding in the !media_ready case is to allow for
mailbox operations to interrogate and/or remediate the device. After
media is repaired then rebinding the cxl_pci driver is expected to
restart the capacity scan.
Suggested-by: Dan Williams <dan.j.williams@intel.com> Fixes: b39cb1052a5c ("cxl/mem: Register CXL memX devices") Reviewed-by: Ira Weiny <ira.weiny@intel.com> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/168445310026.3251520.8124296540679268206.stgit@djiang5-mobl3
[djbw: fixup cxl_test] Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Memory_Info_Valid bit (CXL 3.0 8.1.3.8.2) indicates that the CXL
Range Size High and Size Low registers are valid. The bit must be set
within 1 second of reset deassertion to the device. Check valid bit
before we check the Memory_Active bit when waiting for
cxl_await_media_ready() to ensure that the memory info is valid for
consumption. Also ensures both DVSEC ranges 1 and 2 are ready if DVSEC
Capability indicates they are both supported.
Fixes: 523e594d9cc0 ("cxl/pci: Implement wait for media active") Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Link: https://lore.kernel.org/r/168444687469.3134781.11033518965387297327.stgit@djiang5-mobl3 Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit e335bb51cc15 ("x86/unwind: Ensure stack pointer is aligned")
tried to align the stack pointer in show_trace_log_lvl(), otherwise the
"stack < stack_info.end" check can't guarantee that the last read does
not go past the end of the stack.
However, we have the same problem with the initial value of the stack
pointer, it can also be unaligned. So without this patch this trivial
kernel module
In the pvcalls_new_active_socket() function, most error paths call
pvcalls_back_release_active(fedata->dev, fedata, map) which calls
sock_release() on "sock". The bug is that the caller also frees sock.
Fix this by making every error path in pvcalls_new_active_socket()
release the sock, and don't free it in the caller.
Commit bf5e758f02fc ("genirq/msi: Simplify sysfs handling") reworked the
creation of sysfs entries for MSI IRQs. The creation used to be in
msi_domain_alloc_irqs_descs_locked after calling ops->domain_alloc_irqs.
Then it moved into __msi_domain_alloc_irqs which is an implementation of
domain_alloc_irqs. However, Xen comes with the only other implementation
of domain_alloc_irqs and hence doesn't run the sysfs population code
anymore.
Commit 6c796996ee70 ("x86/pci/xen: Fixup fallout from the PCI/MSI
overhaul") set the flag MSI_FLAG_DEV_SYSFS for the xen msi_domain_info
but that doesn't actually have an effect because Xen uses it's own
domain_alloc_irqs implementation.
Fix this by making use of the fallback functions for sysfs population.
This worked before by coincidence, as the regulator was probed and enabled
before PCI RC probe. But probe order changed since commit 259b93b21a9f
("regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in
4.14") and PCIe supply is enabled after RC.
Fix this by adding the regulator to RC node.
The PCIe vaux regulator still needs to be enabled unconditionally for
Mini-PCIe USB-only devices.
drivers/hwtracing/coresight/coresight-tmc-etr.c:947 tmc_etr_buf_insert_barrier_packet()
error: uninitialized symbol 'bufp'.
The problem is that if tmc_sg_table_get_data() returns -EINVAL, then
when we test if "len < CORESIGHT_BARRIER_PKT_SIZE", the negative "len"
value is type promoted to a high unsigned long value which is greater
than CORESIGHT_BARRIER_PKT_SIZE. Fix this bug by adding an explicit
check for error codes.
Stop restricting the PCI search to a range of PCI domains fed to
pci_get_domain_bus_and_slot(). Instead, use for_each_pci_dev() and
look at all PCI domains in one pass.
On systems with more than 8 sockets, this avoids error messages like
"Information: Invalid level, Can't get TDP control information at
specified levels on cpu 480" from the intel speed select utility.
Fixes: aa2ddd242572 ("platform/x86: ISST: Use numa node id for cpu pci dev mapping") Signed-off-by: Steve Wahl <steve.wahl@hpe.com> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230519160420.2588475-1-steve.wahl@hpe.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shifting signed 32-bit value by 31 bits is undefined, so changing
significant bit to unsigned. It was spotted by UBSAN.
So let's just fix this by using the BIT() helper for all SB_* flags.
Fixes: e462ec50cb5f ("VFS: Differentiate mount flags (MS_*) from internal superblock flags") Signed-off-by: Hao Ge <gehao@kylinos.cn>
Message-Id: <20230424051835.374204-1-gehao@kylinos.cn>
[brauner@kernel.org: use BIT() for all SB_* flags] Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each physical partition can provide multiple services each with UUID.
Each such service can be presented as logical partition with a unique
combination of VM ID and UUID. The number of distinct UUID in a system
will be less than or equal to the number of logical partitions.
However, currently it fails to register more than one logical partition
or service within a physical partition as the device name contains only
VM ID while both VM ID and UUID are maintained in the partition information.
The kernel complains with the below message:
| sysfs: cannot create duplicate filename '/devices/arm-ffa-8001'
| CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.3.0-rc7 #8
| Hardware name: FVP Base RevC (DT)
| Call trace:
| dump_backtrace+0xf8/0x118
| show_stack+0x18/0x24
| dump_stack_lvl+0x50/0x68
| dump_stack+0x18/0x24
| sysfs_create_dir_ns+0xe0/0x13c
| kobject_add_internal+0x220/0x3d4
| kobject_add+0x94/0x100
| device_add+0x144/0x5d8
| device_register+0x20/0x30
| ffa_device_register+0x88/0xd8
| ffa_setup_partitions+0x108/0x1b8
| ffa_init+0x2ec/0x3a4
| do_one_initcall+0xcc/0x240
| do_initcall_level+0x8c/0xac
| do_initcalls+0x54/0x94
| do_basic_setup+0x1c/0x28
| kernel_init_freeable+0x100/0x16c
| kernel_init+0x20/0x1a0
| ret_from_fork+0x10/0x20
| kobject_add_internal failed for arm-ffa-8001 with -EEXIST, don't try to
| register things with the same name in the same directory.
| arm_ffa arm-ffa: unable to register device arm-ffa-8001 err=-17
| ARM FF-A: ffa_setup_partitions: failed to register partition ID 0x8001
By virtue of being random enough to avoid collisions when generated in a
distributed system, there is no way to compress UUID keys to the number
of bits required to identify each. We can eliminate '-' in the name but
it is not worth eliminating 4 bytes and add unnecessary logic for doing
that. Also v1.0 doesn't provide the UUID of the partitions which makes
it hard to use the same for the device name.
So to keep it simple, let us alloc an ID using ida_alloc() and append the
same to "arm-ffa" to make up a unique device name. Also stash the id value
in ffa_dev to help freeing the ID later when the device is destroyed.
Fixes: e781858488b9 ("firmware: arm_ffa: Add initial FFA bus support for device enumeration") Reported-by: Lucian Paul-Trifu <lucian.paul-trifu@arm.com> Link: https://lore.kernel.org/r/20230419-ffa_fixes_6-4-v2-3-d9108e43a176@arm.com Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ffa_drv->remove() is called unconditionally from
ffa_device_remove(). Since the driver registration doesn't check for it
and allows it to be registered without .remove callback, we need to check
for the presence of it before executing it from ffa_device_remove() to
above a NULL pointer dereference like the one below:
Fixes an uninitialized variable in irq_handler() that could lead to
unpredictable behavior in case OP-TEE fails to handle SMC function ID
OPTEE_SMC_GET_ASYNC_NOTIF_VALUE. This change ensures that in that case
get_async_notif_value() properly reports there are no notification
event.
The bq24192 model relies on external charger-type detection and once
that is done the bq24190_charger code will update the input current.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current. This allows the fuel-gauge driver to timely recheck
if the battery is charging after the new input current has been applied
and then it can immediately notify userspace about this.
Fixes: 18f8e6f695ac ("power: supply: bq24190_charger: Get input_current_limit from our supplier") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bq25892 model relies on external charger-type detection and once
that is done the bq25890_charger code will update the input current
and if pumpexpress is used also the input voltage.
In this case, when the initial power_supply_changed() call is made
from the interrupt handler, the input settings are 5V/0.5A which
on many devices is not enough power to charge (while the device is on).
On many devices the fuel-gauge relies in its external_power_changed
callback to timely signal userspace about charging <-> discharging
status changes. Add a power_supply_changed() call after updating
the input current or voltage. This allows the fuel-gauge driver
to timely recheck if the battery is charging after the new input
settings have been applied and then it can immediately notify
userspace about this.
Fixes: 48f45b094dbb ("power: supply: bq25890: Support higher charging voltages through Pump Express+ protocol") Fixes: eab25b4f93aa ("power: supply: bq25890: On the bq25892 set the IINLIM based on external charger detection") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b34 ("bq27x00: Poll battery state") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On gauges where the current register is signed, there is no charging
flag in the flags register. So only checking flags will not result
in power_supply_changed() getting called when e.g. a charger is plugged
in and the current sign changes from negative (discharging) to
positive (charging).
This causes userspace's notion of the status to lag until userspace
does a poll.
And when a power_supply_leds.c LED trigger is used to indicate charging
status with a LED, this LED will lag until the capacity percentage
changes, which may take many minutes (because the LED trigger only is
updated on power_supply_changed() calls).
Fix this by calling bq27xxx_battery_current_and_status() on gauges with
a signed current register and checking if the status has changed.
Fixes: 297a533b3e62 ("bq27x00: Cache battery registers") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa811894 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b76 ("power: bq27xxx_battery: Add interrupt handling support") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b34 ("bq27x00: Poll battery state") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c56f ("power_supply: Add new LED trigger charging-blink-solid-full") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two ways that special characters (not allowed in some
other operating systems like Windows, but allowed in POSIX) have
been mapped in the past ("SFU" and "SFM" mappings) to allow them
to be stored in a range reserved for special chars. The default
for Linux has been to use "mapposix" (ie the SFM mapping) but
the conversion to the new mount API in the 5.11 kernel broke
the ability to override the default mapping of the reserved
characters (like '?' and '*' and '\') via "mapchars" mount option.
This patch fixes that - so can now mount with "mapchars"
mount option to override the default ("mapposix" ie SFM) mapping.
Reported-by: Tyler Spivey <tspivey8@gmail.com> Fixes: 24e0a1eff9e2 ("cifs: switch to new mount api") Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
optlen is fetched without checking whether there is more than one byte to parse.
It can lead to out-of-bounds access.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: c61a40432509 ("[IPV6]: Find option offset by type.") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log