Clearing BSS should only be done once, at the very beginning.
efi_pe_entry() is the entrypoint from the firmware, which may not clear
BSS and so it is done explicitly. However, efi_pe_entry() is also used
as an entrypoint by the mixed mode startup code, in which case BSS will
already have been cleared, and doing it again at this point will corrupt
global variables holding the firmware's GDT/IDT and segment selectors.
So make the memset() conditional on whether the EFI stub is running in
native mode.
The EFI stub on x86 no longer invokes the decompressor as a subsequent
boot stage, but calls into the decompression code directly while running
in the context of the EFI boot services.
This means that when using the native EFI entrypoint (as opposed to the
EFI handover protocol, which clears BSS explicitly), the firmware PE
image loader is being relied upon to ensure that BSS is zeroed before
the EFI stub is entered from the firmware.
As Radek's report proves, this is a bad idea. Not all loaders do this
correctly, which means some global variables that should be statically
initialized to 0x0 may have junk in them.
So clear BSS explicitly when entering via efi_pe_entry(). Note that
zeroing BSS from C code is not generally safe, but in this case, the
following assignment and dereference of a global pointer variable
ensures that the memset() cannot be deferred or reordered.
It is possible to set up dm-integrity with smaller sector size than
the logical sector size of the underlying device. In this situation,
dm-integrity guarantees that the outgoing bios have the same alignment as
incoming bios (so, if you create a filesystem with 4k block size,
dm-integrity would send 4k-aligned bios to the underlying device).
This guarantee was broken when integrity_recheck was implemented.
integrity_recheck sends bio that is aligned to ic->sectors_per_block. So
if we set up integrity with 512-byte sector size on a device with logical
block size 4k, we would be sending unaligned bio. This triggered a bug in
one of our internal tests.
This commit fixes it by determining the actual alignment of the
incoming bio and then makes sure that the outgoing bio in
integrity_recheck has the same alignment.
Fixes: c88f5e553fe3 ("dm-integrity: recheck the integrity tag after a failure") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some IO will dispatch from kworker with different io_context settings
than the submitting task, we may need to specify a priority to avoid
losing priority.
Add IO priority parameter to dm_io() and update all callers.
Co-developed-by: Yibin Ding <yibin.ding@unisoc.com> Signed-off-by: Yibin Ding <yibin.ding@unisoc.com> Signed-off-by: Hongyu Jin <hongyu.jin@unisoc.com> Reviewed-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Stable-dep-of: b4d78cfeb304 ("dm-integrity: align the outgoing bio in integrity_recheck") Signed-off-by: Sasha Levin <sashal@kernel.org>
The tests send 100 pings in 0.1 second intervals and force a timeout of
11 seconds, which is borderline (especially on debug kernels), resulting
in random failures in netdev CI [1].
Fix by increasing the timeout to 20 seconds. It should not prolong the
test unless something is wrong, in which case the test will rightfully
fail.
[1]
# selftests: net/forwarding: vxlan_bridge_1d_port_8472_ipv6.sh
# INFO: Running tests with UDP port 8472
# TEST: ping: local->local [ OK ]
# TEST: ping: local->remote 1 [FAIL]
# Ping failed
[...]
Fixes: b07e9957f220 ("selftests: forwarding: Add VxLAN tests with a VLAN-unaware bridge for IPv6") Fixes: 728b35259e28 ("selftests: forwarding: Add VxLAN tests with a VLAN-aware bridge for IPv6") Reported-by: Paolo Abeni <pabeni@redhat.com> Closes: https://lore.kernel.org/netdev/24a7051fdcd1f156c3704bca39e4b3c41dfc7c4b.camel@redhat.com/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/20240320065717.4145325-1-idosch@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The TX buffer in spi_transfer can be a NULL pointer, so the interrupt
handler may end up writing to the invalid memory and cause crashes.
Add a check to trans->tx_buf before using it.
Fixes: 1ce24864bff4 ("spi: mediatek: Only do dma for 4-byte aligned buffers") Signed-off-by: Fei Shao <fshao@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://msgid.link/r/20240321070942.1587146-2-fshao@chromium.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If nft_netdev_register_hooks() fails, the memory associated with
nft_stats is not freed, causing a memory leak.
This patch fixes it by moving nft_stats_alloc() down after
nft_netdev_register_hooks() succeeds.
Fixes: b9703ed44ffb ("netfilter: nf_tables: support for adding new devices to an existing netdev chain") Signed-off-by: Quan Tian <tianquan23@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the MT753X switches treat frames with :01-0D and :0F MAC DAs as
regular multicast frames, therefore flooding them to user ports.
On page 205, section "8.6.3 Frame filtering" of the active standard, IEEE
Std 802.1Q™-2022, it is stated that frames with 01:80:C2:00:00:00-0F as MAC
DA must only be propagated to C-VLAN and MAC Bridge components. That means
VLAN-aware and VLAN-unaware bridges. On the switch designs with CPU ports,
these frames are supposed to be processed by the CPU (software). So we make
the switch only forward them to the CPU port. And if received from a CPU
port, forward to a single port. The software is responsible of making the
switch conform to the latter by setting a single port as destination port
on the special tag.
This switch intellectual property cannot conform to this part of the
standard fully. Whilst the REV_UN frame tag covers the remaining :04-0D and
:0F MAC DAs, it also includes :22-FF which the scope of propagation is not
supposed to be restricted for these MAC DAs.
Set frames with :01-03 MAC DAs to be trapped to the CPU port(s). Add a
comment for the remaining MAC DAs.
Note that the ingress port must have a PVID assigned to it for the switch
to forward untagged frames. A PVID is set by default on VLAN-aware and
VLAN-unaware ports. However, when the network interface that pertains to
the ingress port is attached to a vlan_filtering enabled bridge, the user
can remove the PVID assignment from it which would prevent the link-local
frames from being trapped to the CPU port. I am yet to see a way to forward
link-local frames while preventing other untagged frames from being
forwarded too.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Whether VLAN-aware or not, on every VID VLAN table entry that has the CPU
port as a member of it, frames are set to egress the CPU port with the VLAN
tag stacked. This is so that VLAN tags can be appended after hardware
special tag (called DSA tag in the context of Linux drivers).
For user ports on a VLAN-unaware bridge, frame ingressing the user port
egresses CPU port with only the special tag.
For user ports on a VLAN-aware bridge, frame ingressing the user port
egresses CPU port with the special tag and the VLAN tag.
This causes issues with link-local frames, specifically BPDUs, because the
software expects to receive them VLAN-untagged.
There are two options to make link-local frames egress untagged. Setting
CONSISTENT or UNTAGGED on the EG_TAG bits on the relevant register.
CONSISTENT means frames egress exactly as they ingress. That means
egressing with the VLAN tag they had at ingress or egressing untagged if
they ingressed untagged. Although link-local frames are not supposed to be
transmitted VLAN-tagged, if they are done so, when egressing through a CPU
port, the special tag field will be broken.
BPDU egresses CPU port with VLAN tag egressing stacked, received on
software:
To prevent confusing the software, force the frame to egress UNTAGGED
instead of CONSISTENT. This way, frames can't possibly be received TAGGED
by software which would have the special tag field broken.
VLAN Tag Egress Procedure
For all frames, one of these options set the earliest in this order will
apply to the frame:
- EG_TAG in certain registers for certain frames.
This will apply to frame with matching MAC DA or EtherType.
- EG_TAG in the address table.
This will apply to frame at its incoming port.
- EG_TAG in the PVC register.
This will apply to frame at its incoming port.
- EG_CON and [EG_TAG per port] in the VLAN table.
This will apply to frame at its outgoing port.
- EG_TAG in the PCR register.
This will apply to frame at its outgoing port.
EG_TAG in certain registers for certain frames:
PPPoE Discovery_ARP/RARP: PPP_EG_TAG and ARP_EG_TAG in the APC register.
IGMP_MLD: IGMP_EG_TAG and MLD_EG_TAG in the IMC register.
BPDU and PAE: BPDU_EG_TAG and PAE_EG_TAG in the BPC register.
REV_01 and REV_02: R01_EG_TAG and R02_EG_TAG in the RGAC1 register.
REV_03 and REV_0E: R03_EG_TAG and R0E_EG_TAG in the RGAC2 register.
REV_10 and REV_20: R10_EG_TAG and R20_EG_TAG in the RGAC3 register.
REV_21 and REV_UN: R21_EG_TAG and RUN_EG_TAG in the RGAC4 register.
With this change, it can be observed that a bridge interface with stp_state
and vlan_filtering enabled will properly block ports now.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When there are heavy load, cpumap kernel threads can be busy polling
packets from redirect queues and block out RCU tasks from reaching
quiescent states. It is insufficient to just call cond_resched() in such
context. Periodically raise a consolidated RCU QS before cond_resched
fixes the problem.
Fixes: 6710e1126934 ("bpf: introduce new bpf cpu map type BPF_MAP_TYPE_CPUMAP") Reviewed-by: Jesper Dangaard Brouer <hawk@kernel.org> Signed-off-by: Yan Zhai <yan@cloudflare.com> Acked-by: Paul E. McKenney <paulmck@kernel.org> Acked-by: Jesper Dangaard Brouer <hawk@kernel.org> Link: https://lore.kernel.org/r/c17b9f1517e19d813da3ede5ed33ee18496bb5d8.1710877680.git.yan@cloudflare.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
NAPI threads can keep polling packets under load. Currently it is only
calling cond_resched() before repolling, but it is not sufficient to
clear out the holdout of RCU tasks, which prevent BPF tracing programs
from detaching for long period. This can be reproduced easily with
following set up:
ip netns add test1
ip netns add test2
ip -n test1 link add veth1 type veth peer name veth2 netns test2
ip -n test1 link set veth1 up
ip -n test1 link set lo up
ip -n test2 link set veth2 up
ip -n test2 link set lo up
ip -n test1 addr add 192.168.1.2/31 dev veth1
ip -n test1 addr add 1.1.1.1/32 dev lo
ip -n test2 addr add 192.168.1.3/31 dev veth2
ip -n test2 addr add 2.2.2.2/31 dev lo
ip -n test1 route add default via 192.168.1.3
ip -n test2 route add default via 192.168.1.2
for i in `seq 10 210`; do
for j in `seq 10 210`; do
ip netns exec test2 iptables -I INPUT -s 3.3.$i.$j -p udp --dport 5201
done
done
ip netns exec test2 ethtool -K veth2 gro on
ip netns exec test2 bash -c 'echo 1 > /sys/class/net/veth2/threaded'
ip netns exec test1 ethtool -K veth1 tso off
Then run an iperf3 client/server and a bpftrace script can trigger it:
When under heavy load, network processing can run CPU-bound for many
tens of seconds. Even in preemptible kernels (non-RT kernel), this can
block RCU Tasks grace periods, which can cause trace-event removal to
take more than a minute, which is unacceptably long.
This commit therefore creates a new helper function that passes through
both RCU and RCU-Tasks quiescent states every 100 milliseconds. This
hard-coded value suffices for current workloads.
Suggested-by: Paul E. McKenney <paulmck@kernel.org> Reviewed-by: Jesper Dangaard Brouer <hawk@kernel.org> Signed-off-by: Yan Zhai <yan@cloudflare.com> Reviewed-by: Paul E. McKenney <paulmck@kernel.org> Acked-by: Jesper Dangaard Brouer <hawk@kernel.org> Link: https://lore.kernel.org/r/90431d46ee112d2b0af04dbfe936faaca11810a5.1710877680.git.yan@cloudflare.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: d6dbbb11247c ("net: report RCU QS on threaded NAPI repolling") Signed-off-by: Sasha Levin <sashal@kernel.org>
Clone already always provides a current view of the lookup table, use it
to destroy the set, otherwise it is possible to destroy elements twice.
This fix requires:
212ed75dc5fb ("netfilter: nf_tables: integrate pipapo into commit protocol")
which came after:
9827a0e6e23b ("netfilter: nft_set_pipapo: release elements in clone from abort path").
Fixes: 9827a0e6e23b ("netfilter: nft_set_pipapo: release elements in clone from abort path") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For PF to AF interrupt vector and VF to AF vector same
interrupt handler is registered which is causing race condition.
When two interrupts are raised to two CPUs at same time
then two cores serve same event corrupting the data.
Fixes: 7304ac4567bc ("octeontx2-af: Add mailbox IRQ and msg handlers") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When PF sending link status messages to VF, it is possible
that by the time link_event_task work function is executed
VF might have brought down. Hence before sending VF link
status message check whether VF is up to receive it.
Fixes: ad513ed938c9 ("octeontx2-vf: Link event notification support") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only one execution context for the workqueue used for PF and
VFs mailbox communication is incorrect since multiple works are
queued simultaneously by all the VFs and PF link UP messages.
Hence use default number of execution contexts by passing zero
as max_active to alloc_workqueue function. With this fix in place,
modify UP messages also to wait until completion.
Fixes: d424b6c02415 ("octeontx2-pf: Enable SRIOV and added VF mbox handling") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
During VF driver remove, a message is sent to detach VF
resources to PF but VF is not waiting until message is
complete. Also mailbox interrupts need to be turned off
after the detach resource message is complete. This patch
fixes that problem.
Fixes: 05fcc9e08955 ("octeontx2-pf: Attach NIX and NPA block LFs") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A single line of interrupt is used to receive up notifications
and down reply messages from AF to PF (similarly from PF to its VF).
PF acts as bridge and forwards VF messages to AF and sends respsones
back from AF to VF. When an async event like link event is received
by up message when PF is in middle of forwarding VF message then
mailbox errors occur because PF state machine is corrupted.
Since VF is a separate driver or VF driver can be in a VM it is
not possible to serialize from the start of communication at VF.
Hence to differentiate between type of messages at PF this patch makes
sender to set mbox data register with distinct values for up and down
messages. Sender also checks whether previous interrupt is received
before triggering current interrupt by waiting for mailbox data register
to become zero.
Fixes: 5a6d7c9daef3 ("octeontx2-pf: Mailbox communication with AF") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix race condition leading to system crash during EEH error handling
During EEH error recovery, the bnx2x driver's transmit timeout logic
could cause a race condition when handling reset tasks. The
bnx2x_tx_timeout() schedules reset tasks via bnx2x_sp_rtnl_task(),
which ultimately leads to bnx2x_nic_unload(). In bnx2x_nic_unload()
SGEs are freed using bnx2x_free_rx_sge_range(). However, this could
overlap with the EEH driver's attempt to reset the device using
bnx2x_io_slot_reset(), which also tries to free SGEs. This race
condition can result in system crashes due to accessing freed memory
locations in bnx2x_free_rx_sge()
799 static inline void bnx2x_free_rx_sge(struct bnx2x *bp,
800 struct bnx2x_fastpath *fp, u16 index)
801 {
802 struct sw_rx_page *sw_buf = &fp->rx_page_ring[index];
803 struct page *page = sw_buf->page;
....
where sw_buf was set to NULL after the call to dma_unmap_page()
by the preceding thread.
Memory for the "checksums" pointer will leak if the data is rechecked
after checksum failure (because the associated kfree won't happen due
to 'goto skip_io').
Fix this by freeing the checksums memory before recheck, and just use
the "checksum_onstack" memory for storing checksum during recheck.
Fixes: c88f5e553fe3 ("dm-integrity: recheck the integrity tag after a failure") Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
read_poll_timeout inside phy_read_poll_timeout can set val negative
in some cases (for example, __mdiobus_read inside phy_read can return
-EOPNOTSUPP).
Supposedly, commit 4ec732951702 ("net: phylib: fix phy_read*_poll_timeout()")
should fix problems with wrong-signed vals, but I do not see how
as val is sent to phy_read as is and __val = phy_read (not val)
is checked for sign.
Change val type for signed to allow better error handling as done in other
phy_read_poll_timeout callers. This will not fix any error handling
by itself, but allows, for example, to modify cond with appropriate
sign check or check resulting val separately.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 014068dcb5b1 ("net: phy: genphy_loopback: add link speed configuration") Signed-off-by: Nikita Kiryushin <kiryushin@ancud.ru> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20240315175052.8049-1-kiryushin@ancud.ru Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If EOF is encountered, ceph_sync_read() return value is adjusted down
according to i_size, but the "to" iter is advanced by the actual number
of bytes read. Then, when retrying, the remainder of the range may be
skipped incorrectly.
Ensure that the "to" iter is advanced only until EOF.
[ idryomov: changelog ]
Fixes: c3d8e0b5de48 ("ceph: return the real size read when it hits EOF") Reported-by: Frank Hsiao <frankhsiao@qnap.com> Signed-off-by: Xiubo Li <xiubli@redhat.com> Reviewed-by: Ilya Dryomov <idryomov@gmail.com> Tested-by: Frank Hsiao <frankhsiao@qnap.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the referenced commit, the xfrm_inner_extract_output() function
uses the protocol field to determine the address family. So not setting
it for IPv4 raw sockets meant that such packets couldn't be tunneled via
IPsec anymore.
IPv6 raw sockets are not affected as they already set the protocol since 9c9c9ad5fae7 ("ipv6: set skb->protocol on tcp, raw and ip6_append_data
genereated skbs").
Fixes: f4796398f21b ("xfrm: Remove inner/outer modes from output path") Signed-off-by: Tobias Brunner <tobias@strongswan.org> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Link: https://lore.kernel.org/r/c5d9a947-eb19-4164-ac99-468ea814ce20@strongswan.org Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A failure during registration of the netdev notifier was not handled at
all. A failure during netlink initialization did not unregister the netdev
notifier.
Handle failures of netdev notifier registration and netlink initialization.
Both functions should only return negative values on failure and thereby
lead to the hsr module not being loaded.
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by: Felix Maurer <fmaurer@redhat.com> Reviewed-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Breno Leitao <leitao@debian.org> Link: https://lore.kernel.org/r/3ce097c15e3f7ace98fc7fd9bcbf299f092e63d1.1710504184.git.fmaurer@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
acquire/release_in_xmit() work as bit lock in rds_send_xmit(), so they
are expected to ensure acquire/release memory ordering semantics.
However, test_and_set_bit/clear_bit() don't imply such semantics, on
top of this, following smp_mb__after_atomic() does not guarantee release
ordering (memory barrier actually should be placed before clear_bit()).
Instead, we use clear_bit_unlock/test_and_set_bit_lock() here.
Syzkaller with KCSAN identified a data-race issue when accessing
keypair->receiving_counter.counter. Use READ_ONCE() and WRITE_ONCE()
annotations to mark the data race as intentional.
BUG: KCSAN: data-race in wg_packet_decrypt_worker / wg_packet_rx_poll
write to 0xffff888107765888 of 8 bytes by interrupt on cpu 0:
counter_validate drivers/net/wireguard/receive.c:321 [inline]
wg_packet_rx_poll+0x3ac/0xf00 drivers/net/wireguard/receive.c:461
__napi_poll+0x60/0x3b0 net/core/dev.c:6536
napi_poll net/core/dev.c:6605 [inline]
net_rx_action+0x32b/0x750 net/core/dev.c:6738
__do_softirq+0xc4/0x279 kernel/softirq.c:553
do_softirq+0x5e/0x90 kernel/softirq.c:454
__local_bh_enable_ip+0x64/0x70 kernel/softirq.c:381
__raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
_raw_spin_unlock_bh+0x36/0x40 kernel/locking/spinlock.c:210
spin_unlock_bh include/linux/spinlock.h:396 [inline]
ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
wg_packet_decrypt_worker+0x6c5/0x700 drivers/net/wireguard/receive.c:499
process_one_work kernel/workqueue.c:2633 [inline]
...
read to 0xffff888107765888 of 8 bytes by task 3196 on cpu 1:
decrypt_packet drivers/net/wireguard/receive.c:252 [inline]
wg_packet_decrypt_worker+0x220/0x700 drivers/net/wireguard/receive.c:501
process_one_work kernel/workqueue.c:2633 [inline]
process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2706
worker_thread+0x525/0x730 kernel/workqueue.c:2787
...
Fixes: a9e90d9931f3 ("wireguard: noise: separate receive counter from send counter") Reported-by: syzbot+d1de830e4ecdaac83d89@syzkaller.appspotmail.com Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MLX driver was not updating its control virtqueue size at set_vq_num
and instead always initialized to MLX5_CVQ_MAX_ENT (16) at
setup_cvq_vring.
Qemu would try to set the size to 64 by default, however, because the
CVQ size always was initialized to 16, an error would be thrown when
sending >16 control messages (as used-ring entry 17 is initialized to 0).
For example, starting a guest with x-svq=on and then executing the
following command would produce the error below:
# for i in {1..20}; do ifconfig eth0 hw ether XX:xx:XX:xx:XX:XX; done
qemu-system-x86_64: Insufficient written data (0)
[ 435.331223] virtio_net virtio0: Failed to set mac address by vq command.
SIOCSIFHWADDR: Invalid argument
Acked-by: Dragos Tatulea <dtatulea@nvidia.com> Acked-by: Eugenio Pérez <eperezma@redhat.com> Signed-off-by: Jonah Palmer <jonah.palmer@oracle.com>
Message-Id: <20240216142502.78095-1-jonah.palmer@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Tested-by: Lei Yang <leiyang@redhat.com> Fixes: 5262912ef3cf ("vdpa/mlx5: Add support for control VQ and MAC setting") Signed-off-by: Sasha Levin <sashal@kernel.org>
vdpasim_do_reset sets running to true, which is wrong, as it allows
vdpasim_kick_vq to post work requests before the device has been
configured. To fix, do not set running until VIRTIO_CONFIG_S_DRIVER_OK
is set.
Fixes: 0c89e2a3a9d0 ("vdpa_sim: Implement suspend vdpa op") Signed-off-by: Steve Sistare <steven.sistare@oracle.com> Reviewed-by: Eugenio Pérez <eperezma@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com>
Message-Id: <1707517807-137331-1-git-send-email-steven.sistare@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As well noted by Pekka[1], the rounding of drm_fixp2int_round is wrong.
To round a number, you need to add 0.5 to the number and floor that,
drm_fixp2int_round() is adding 0.0000076. Make it add 0.5.
c712c05e46c8 ("spi: imx: fix the burst length at DMA mode and CPU mode")
corrects three cases of setting the ECSPI burst length but erroneously
leaves the in-range CPU case one bit to big (in that field a value of
0 means 1 bit). The effect was that transmissions that should have been
8-bit bytes appeared as 9-bit causing failed communication with SPI
devices.
On MT7530, the HT_XTAL_FSEL field of the HWTRAP register stores a 2-bit
value that represents the frequency of the crystal oscillator connected to
the switch IC. The field is populated by the state of the ESW_P4_LED_0 and
ESW_P4_LED_0 pins, which is done right after reset is deasserted.
On MT7531, the XTAL25 bit of the STRAP register stores this. The LAN0LED0
pin is used to populate the bit. 25MHz when the pin is high, 40MHz when
it's low.
These pins are also used with LEDs, therefore, their state can be set to
something other than the bootstrapping configuration. For example, a link
may be established on port 3 before the DSA subdriver takes control of the
switch which would set ESW_P3_LED_0 to high.
Currently on mt7530_setup() and mt7531_setup(), 1000 - 1100 usec delay is
described between reset assertion and deassertion. Some switch ICs in real
life conditions cannot always have these pins set back to the bootstrapping
configuration before reset deassertion in this amount of delay. This causes
wrong crystal frequency to be selected which puts the switch in a
nonfunctional state after reset deassertion.
The tests below are conducted on an MT7530 with a 40MHz crystal oscillator
by Justin Swartz.
With a cable from an active peer connected to port 3 before reset, an
incorrect crystal frequency (0b11 = 25MHz) is selected:
[1] Reset is asserted.
[2] Period of 1000 - 1100 usec.
[3] Reset is deasserted.
[4] Period of 315 usec. HWTRAP register is populated with incorrect
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Increase the delay between reset_control_assert() and
reset_control_deassert(), and gpiod_set_value_cansleep(priv->reset, 0) and
gpiod_set_value_cansleep(priv->reset, 1) to 5000 - 5100 usec. This amount
ensures a higher possibility that the switch IC will have these pins back
to the bootstrapping configuration before reset deassertion.
With a cable from an active peer connected to port 3 before reset, the
correct crystal frequency (0b10 = 40MHz) is selected:
[1] Reset is asserted.
[2] Period of 5000 - 5100 usec.
[2-1] ESW_P3_LED_0 goes low.
[2-2] Remaining period of 5000 - 5100 usec.
[3] Reset is deasserted.
[4] Period of 310 usec. HWTRAP register is populated with bootstrapped
XTAL frequency.
[5] Signals reflect the bootstrapped configuration.
Revert commit 2920dd92b980 ("net: dsa: mt7530: disable LEDs before reset").
Changing the state of pins via reset assertion is simpler and more
efficient than doing so by setting the LED controller off.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch") Fixes: c288575f7810 ("net: dsa: mt7530: Add the support of MT7531 switch") Co-developed-by: Justin Swartz <justin.swartz@risingedge.co.za> Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit d3256efd8e8b ("veth: allow enabling NAPI even without XDP") tried to fix
the fact that GRO was not possible without XDP, because veth did not use NAPI
without XDP. However, it also introduced the behaviour that GRO is always
enabled, when XDP is enabled.
While it might be desired for most cases, it is confusing for the user at best
as the GRO flag suddenly changes, when an XDP program is attached. It also
introduces some complexities in state management as was partially addressed in
commit fe9f801355f0 ("net: veth: clear GRO when clearing XDP even when down").
But the biggest problem is that it is not possible to disable GRO at all, when
an XDP program is attached, which might be needed for some use cases.
Fix this by not touching the GRO flag on XDP enable/disable as the code already
supports switching to NAPI if either GRO or XDP is requested.
Link: https://lore.kernel.org/lkml/20240311124015.38106-1-ignat@cloudflare.com/ Fixes: d3256efd8e8b ("veth: allow enabling NAPI even without XDP") Fixes: fe9f801355f0 ("net: veth: clear GRO when clearing XDP even when down") Signed-off-by: Ignat Korchagin <ignat@cloudflare.com> Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
BUG: KCSAN: data-race in dev_queue_xmit_nit / packet_setsockopt
write to 0xffff888107804542 of 1 bytes by task 22618 on cpu 0:
packet_setsockopt+0xd83/0xfd0 net/packet/af_packet.c:4003
do_sock_setsockopt net/socket.c:2311 [inline]
__sys_setsockopt+0x1d8/0x250 net/socket.c:2334
__do_sys_setsockopt net/socket.c:2343 [inline]
__se_sys_setsockopt net/socket.c:2340 [inline]
__x64_sys_setsockopt+0x66/0x80 net/socket.c:2340
do_syscall_64+0xd3/0x1d0
entry_SYSCALL_64_after_hwframe+0x6d/0x75
read to 0xffff888107804542 of 1 bytes by task 27 on cpu 1:
dev_queue_xmit_nit+0x82/0x620 net/core/dev.c:2248
xmit_one net/core/dev.c:3527 [inline]
dev_hard_start_xmit+0xcc/0x3f0 net/core/dev.c:3547
__dev_queue_xmit+0xf24/0x1dd0 net/core/dev.c:4335
dev_queue_xmit include/linux/netdevice.h:3091 [inline]
batadv_send_skb_packet+0x264/0x300 net/batman-adv/send.c:108
batadv_send_broadcast_skb+0x24/0x30 net/batman-adv/send.c:127
batadv_iv_ogm_send_to_if net/batman-adv/bat_iv_ogm.c:392 [inline]
batadv_iv_ogm_emit net/batman-adv/bat_iv_ogm.c:420 [inline]
batadv_iv_send_outstanding_bat_ogm_packet+0x3f0/0x4b0 net/batman-adv/bat_iv_ogm.c:1700
process_one_work kernel/workqueue.c:3254 [inline]
process_scheduled_works+0x465/0x990 kernel/workqueue.c:3335
worker_thread+0x526/0x730 kernel/workqueue.c:3416
kthread+0x1d1/0x210 kernel/kthread.c:388
ret_from_fork+0x4b/0x60 arch/x86/kernel/process.c:147
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:243
value changed: 0x00 -> 0x01
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 27 Comm: kworker/u8:1 Tainted: G W 6.8.0-syzkaller-08073-g480e035fc4c7 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024
Workqueue: bat_events batadv_iv_send_outstanding_bat_ogm_packet
Fixes: fa788d986a3a ("packet: add sockopt to ignore outgoing packets") Reported-by: syzbot+c669c1136495a2e7c31f@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/CANn89i+Z7MfbkBLOv=p7KZ7=K1rKHO4P1OL5LYDCtBiyqsa9oQ@mail.gmail.com/T/#t Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Jason Xing <kerneljasonxing@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In bind_evtchn_to_irq_chip() don't increment the refcnt of the event
channel blindly. In case the event channel is NOT refcounted, issue a
warning instead.
Add an additional safety net by doing the refcnt increment only if the
caller has specified IRQF_SHARED in the irqflags parameter.
When unbinding a user event channel, the related handler might be
called a last time in case the kernel was built with
CONFIG_DEBUG_SHIRQ. This might cause a WARN() in the handler.
Avoid that by adding an "unbinding" flag to struct user_event which
will short circuit the handler.
Taking the ctx lock is not enough to use the deferred request completion
infrastructure, it'll get queued into the list but no one would expect
it there, so it will sit there until next io_submit_flush_completions().
It's hard to care about the cancellation path, so complete it via tw.
A patch to resolve an issue was found in MediaTek's GPL-licensed SDK:
In the mtk_ppe_stop() function, the PPE scan mode is not disabled before
disabling the PPE. This can potentially lead to a hang during the process
of disabling the PPE.
Without this patch, the PPE may experience a hang during the reboot test.
We found a issue on production environment while using NVMe over RDMA,
admin_q reconnect failed forever while remote target and network is ok.
After dig into it, we found it may caused by a ABBA deadlock due to tag
allocation. In my case, the tag was hold by a keep alive request
waiting inside admin_q, as we quiesced admin_q while reset ctrl, so the
request maked as idle and will not process before reset success. As
fabric_q shares tagset with admin_q, while reconnect remote target, we
need a tag for connect command, but the only one reserved tag was held
by keep alive command which waiting inside admin_q. As a result, we
failed to reconnect admin_q forever. In order to fix this issue, I
think we should keep two reserved tags for admin queue.
Fixes: ed01fee283a0 ("nvme-fabrics: only reserve a single tag") Signed-off-by: Chunguang Xu <chunguang.xu@shopee.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
txgbe register clk which name is i2c_designware.pci_dev_id(),
clk_name will be stored in clk_lookup_alloc. If PCIe bus number
is larger than 0x39, clk_name size will be larger than 20 bytes.
It exceeds clk_lookup_alloc MAX_DEV_ID limits. So the driver
shortened clk_name.
CPU: 1 PID: 5033 Comm: syz-executor334 Not tainted 6.7.0-syzkaller-00562-g9f8413c4a66f #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023
=====================================================
If the packet type ID field in the Ethernet header is either ETH_P_PRP or
ETH_P_HSR, but it is not followed by an HSR tag, hsr_get_skb_sequence_nr()
reads an invalid value as a sequence number. This causes the above issue.
This patch fixes the issue by returning NULL if the Ethernet header is not
followed by an HSR tag.
syzbot reported a warning in sk_nulls_del_node_init_rcu().
The commit 66b60b0c8c4a ("dccp/tcp: Unhash sk from ehash for tb2 alloc
failure after check_estalblished().") tried to fix an issue that an
unconnected socket occupies an ehash entry when bhash2 allocation fails.
In such a case, we need to revert changes done by check_established(),
which does not hold refcnt when inserting socket into ehash.
So, to revert the change, we need to __sk_nulls_add_node_rcu() instead
of sk_nulls_add_node_rcu().
Otherwise, sock_put() will cause refcnt underflow and leak the socket.
Looking at the error path of __io_uaddr_map, if we fail after pinning
the pages for any reasons, ret will be set to -EINVAL and the error
handler won't properly release the pinned pages.
I didn't manage to trigger it without forcing a failure, but it can
happen in real life when memory is heavily fragmented.
In the existing code, per-policy flags don't have any impact i.e.
if cpufreq_driver boost is enabled and boost is disabled for one or
more of the policies, the cpufreq driver will behave as if boost is
enabled.
Fix this by incorporating per-policy boost flag in the policy->max
computation used in cpufreq_frequency_table_cpuinfo and setting the
default per-policy boost to mirror the cpufreq_driver boost flag.
Fixes: 218a06a79d9a ("cpufreq: Support per-policy performance boost") Reported-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Dhruva Gole <d-gole@ti.com> Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Tested-by:Yipeng Zou <zouyipeng@huawei.com> <mailto:zouyipeng@huawei.com> Reviewed-by: Yipeng Zou <zouyipeng@huawei.com> <mailto:zouyipeng@huawei.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A previous bugfix added a call to kcalloc(), which starting in gcc-14
causes a harmless warning about the argument order:
drivers/soc/fsl/dpio/dpio-service.c: In function 'dpaa2_io_service_enqueue_multiple_desc_fq':
drivers/soc/fsl/dpio/dpio-service.c:526:29: error: 'kcalloc' sizes specified with 'sizeof' in the earlier argument and not in the later argument [-Werror=calloc-transposed-args]
526 | ed = kcalloc(sizeof(struct qbman_eq_desc), 32, GFP_KERNEL);
| ^~~~~~
drivers/soc/fsl/dpio/dpio-service.c:526:29: note: earlier argument should specify number of elements, later size of each element
Since the two are only multiplied, the order does not change the
behavior, so just fix it now to shut up the compiler warning.
taprio_parse_tc_entry() is not correctly checking
TCA_TAPRIO_TC_ENTRY_INDEX attribute:
int tc; // Signed value
tc = nla_get_u32(tb[TCA_TAPRIO_TC_ENTRY_INDEX]);
if (tc >= TC_QOPT_MAX_QUEUE) {
NL_SET_ERR_MSG_MOD(extack, "TC entry index out of range");
return -ERANGE;
}
syzbot reported that it could fed arbitary negative values:
Fixes: a54fc09e4cba ("net/sched: taprio: allow user input of per-tc max SDU") Reported-and-tested-by: syzbot+a340daa06412d6028918@syzkaller.appspotmail.com Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current average steal timer calculation produces volatile and inflated
values. The only user of this value is KVM so far and it uses that to
decide whether or not to yield the vCPU which is seeing steal time.
KVM compares average steal timer to a threshold and if the threshold
is past then it does not allow CPU polling and yields it to host, else
it keeps the CPU by polling.
Since KVM's steal time threshold is very low by default (%10) it most
likely is not effected much by the bloated average steal timer values
because the operating region is pretty small. However there might be
new users in the future who might rely on this number. Fix average
steal timer calculation by changing the formula from:
This ensures that avg_steal_timer is actually a naive average of steal
timer values. It now closely follows steal timer values but of course
in a smoother manner.
Fixes: 152e9b8676c6 ("s390/vtime: steal time exponential moving average") Signed-off-by: Mete Durlu <meted@linux.ibm.com> Acked-by: Heiko Carstens <hca@linux.ibm.com> Acked-by: Christian Borntraeger <borntraeger@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use wake_up API instead of wake_up_interruptible, since
wait_event_timeout API is used for waiting on command completion.
Fixes: 1463f382f58d ("octeontx2-af: Add support for CGX link management") Signed-off-by: Linu Cherian <lcherian@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The notable thing here is 0x4001 in connect(), which is RDS_TCP_PORT.
So, the scenario would be:
1. unshare(CLONE_NEWNET) creates a per netns tcp listener in
rds_tcp_listen_init().
2. syz-executor connect()s to it and creates a reqsk.
3. syz-executor exit()s immediately.
4. netns is dismantled. [0]
5. reqsk timer is fired, and UAF happens while freeing reqsk. [1]
6. listener is freed after RCU grace period. [2]
Basically, reqsk assumes that the listener guarantees netns safety
until all reqsk timers are expired by holding the listener's refcount.
However, this was not the case for kernel sockets.
Commit 740ea3c4a0b2 ("tcp: Clean up kernel listener's reqsk in
inet_twsk_purge()") fixed this issue only for per-netns ehash.
Allocated by task 258 on cpu 0 at 83.612050s:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (mm/kasan/common.c:68)
__kasan_slab_alloc (mm/kasan/common.c:343)
kmem_cache_alloc (mm/slub.c:3813 mm/slub.c:3860 mm/slub.c:3867)
copy_net_ns (./include/linux/slab.h:701 net/core/net_namespace.c:421 net/core/net_namespace.c:480)
create_new_namespaces (kernel/nsproxy.c:110)
unshare_nsproxy_namespaces (kernel/nsproxy.c:228 (discriminator 4))
ksys_unshare (kernel/fork.c:3429)
__x64_sys_unshare (kernel/fork.c:3496)
do_syscall_64 (arch/x86/entry/common.c:52 arch/x86/entry/common.c:83)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:129)
Freed by task 27 on cpu 0 at 329.158864s:
kasan_save_stack (mm/kasan/common.c:48)
kasan_save_track (mm/kasan/common.c:68)
kasan_save_free_info (mm/kasan/generic.c:643)
__kasan_slab_free (mm/kasan/common.c:265)
kmem_cache_free (mm/slub.c:4299 mm/slub.c:4363)
cleanup_net (net/core/net_namespace.c:456 net/core/net_namespace.c:446 net/core/net_namespace.c:639)
process_one_work (kernel/workqueue.c:2638)
worker_thread (kernel/workqueue.c:2700 kernel/workqueue.c:2787)
kthread (kernel/kthread.c:388)
ret_from_fork (arch/x86/kernel/process.c:153)
ret_from_fork_asm (arch/x86/entry/entry_64.S:250)
The buggy address belongs to the object at ffff88801b370000
which belongs to the cache net_namespace of size 4352
The buggy address is located 1024 bytes inside of
freed 4352-byte region [ffff88801b370000, ffff88801b371100)
Later attempts to refault the bo won't happen and the whole
GPU does to lunch. I think Christian's refactoring of this
code out to the driver broke this not very well tested path.
Fixes: 141b15e59175 ("drm/nouveau: move io_reserve_lru handling into the driver v5") Cc: Christian König <christian.koenig@amd.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Danilo Krummrich <dakr@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240311072037.287905-1-airlied@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The sample rates set by the rockchip_i2s_tdm driver in master mode are
inaccurate up to 5% in several cases, due to the driver logic to configure
clocks and a nasty interaction with the Common Clock Framework.
To understand what happens, here is the relevant section of the clock tree
(slightly simplified), along with the names used in the driver:
This is what happens when playing back e.g. at 192 kHz using
audio-graph-card (when recording the same applies, only s/tx/rx/):
0. at probe, rockchip_i2s_tdm_set_sysclk() stores the passed frequency in
i2s_tdm->mclk_tx_freq (*) which is 50176000, and that is never modified
afterwards
1. when playback is started, rockchip_i2s_tdm_hw_params() is called and
does the following two calls
2. rockchip_i2s_tdm_calibrate_mclk():
2a. selects mclk_root0 (vpll0) as a parent for mclk_parent
(mclk_tx_src), which is OK because the vpll0 rate is a good for
192000 (and sumbultiple) rates
2b. sets the mclk_root frequency based on ppm calibration computations
2c. sets mclk_tx_src to 49152000 (= 256 * 192000), which is also OK as
it is a multiple of the required bit clock
3. rockchip_i2s_tdm_set_mclk()
3a. calls clk_set_rate() to set the rate of mclk_tx (clk_i2s2_8ch_tx)
to the value of i2s_tdm->mclk_tx_freq (*), i.e. 50176000 which is
not a multiple of the sampling frequency -- this is not OK
3a1. clk_set_rate() reacts by reparenting clk_i2s2_8ch_tx_src to
vpll1 -- this is not OK because the default vpll1 rate can be
divided to get 44.1 kHz and related rates, not 192 kHz
The result is that the driver does a lot of ad-hoc decisions about clocks
and ends up in using the wrong parent at an unoptimal rate.
Step 0 is one part of the problem: unless the card driver calls set_sysclk
at each stream start, whatever rate is set in mclk_tx_freq during boot will
be taken and used until reboot. Moreover the driver does not care if its
value is not a multiple of any audio frequency.
Another part of the problem is that the whole reparenting and clock rate
setting logic is conflicting with the CCF algorithms to achieve largely the
same goal: selecting the best parent and setting the closest clock
rate. And it turns out that only calling once clk_set_rate() on
clk_i2s2_8ch_tx picks the correct vpll and sets the correct rate.
The fix is based on removing the custom logic in the driver to select the
parent and set the various clocks, and just let the Clock Framework do it
all. As a side effect, the set_sysclk() op becomes useless because we now
let the CCF compute the appropriate value for the sampling rate. It also
implies that the whole calibration logic is now dead code and so it is
removed along with the "PCM Clock Compensation in PPM" kcontrol, which has
always been broken anyway. The handling of the 4 optional clocks also
becomes dead code and is removed.
The actual rates have been tested playing 30 seconds of audio at various
sampling rates before and after this change using sox:
time play -r <sample_rate> -n synth 30 sine 950 gain -3
The time reported in the table below is the 'real' value reported by the
'time' command in the above command line.
While the tests are running the clock tree confirms that:
* without the patch, vpll1 is always used and clk_i2s2_8ch_tx always
produces 50176000 Hz, which cannot be divided for most audio rates
except the slowest ones, generating inaccurate rates
* with the patch:
- for 192000 Hz vpll0 is used
- for 176400 Hz vpll1 is used
- clk_i2s2_8ch_tx always produces (256 * <rate>) Hz
Tested on the RK3308 using the internal audio codec.
fsl_lpspi_probe() is allocating/disposing memory manually with
spi_alloc_host()/spi_alloc_target(), but uses
devm_spi_register_controller(). In case of error after the latter call the
memory will be explicitly freed in the probe function by
spi_controller_put() call, but used afterwards by "devm" management outside
probe() (spi_unregister_controller() <- devm_spi_unregister() below).
This kind of state is per-syscall, and since we're doing the waiting off
entering the io_uring_enter(2) syscall, there's no way that iowait can
already be set for this case. Simplify it by setting it if we need to,
and always clearing it to 0 when done.
Fixes: 7b72d661f1f2 ("io_uring: gate iowait schedule on having pending requests") Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using __exit for the remove function results in the remove callback
being discarded with SND_SOC_TLV320ADC3XXX=y. When such a device gets
unbound (e.g. using sysfs or hotplug), the driver is just removed
without the cleanup being performed. This results in resource leaks. Fix
it by compiling in the remove callback unconditionally.
Currently, the secondary CPUs in Hyper-V VTL context lack support for
parallel startup. Therefore, relying on the single initial_stack fetched
from the current task structure suffices for all vCPUs.
However, common initial_stack risks stack corruption when parallel startup
is enabled. In order to facilitate parallel startup, use the initial_stack
from the per CPU idle thread instead of the current task.
Fixes: 3be1bc2fe9d2 ("x86/hyperv: VTL support for Hyper-V") Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com> Reviewed-by: Michael Kelley <mhklinux@outlook.com> Link: https://lore.kernel.org/r/1709452896-13342-1-git-send-email-ssengar@linux.microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <1709452896-13342-1-git-send-email-ssengar@linux.microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the variable irqflags is being set but is not being used,
it appears it should be used in the call to net2272_probe_fin
rather than IRQF_TRIGGER_LOW being used. Kudos to Uwe Kleine-König
for suggesting the fix.
Cleans up clang scan build warning:
drivers/usb/gadget/udc/net2272.c:2610:15: warning: variable 'irqflags'
set but not used [-Wunused-but-set-variable]
Fixes: ceb80363b2ec ("USB: net2272: driver for PLX NET2272 USB device controller") Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20240307181734.2034407-1-colin.i.king@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The get_channel_from_mode() function is supposed to return the channel
which matches the mode. But it has a bug where if it doesn't find a
matching channel then it returns the last channel. It should return
NULL instead.
Also remove an unnecessary NULL check on "channel".
Fixes: 2870b52bae4c ("greybus: lights: add lights implementation") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com> Reviewed-by: Alex Elder <elder@linaro.org> Link: https://lore.kernel.org/r/379c0cb4-39e0-4293-8a18-c7b1298e5420@moroto.mountain Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It seems a copy&paste mistake that suspend callback removes the GPIO
device. There is no counterpart of this action, means once suspended
there is no more GPIO device available untile full unbind-bind cycle
is performed. Remove suspicious GPIO device removal in suspend.
Fixes: d0aeaa83f0b0 ("serial: exar: split out the exar code from 8250_pci") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20240219150627.2101198-2-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
IRQ_DOMAIN is a hidden (not user visible) symbol. Users cannot set
it directly thru "make *config", so drivers should select it instead
of depending on it if they need it.
Relying on it being set for a dependency is risky.
Consistently using "select" or "depends on" can also help reduce
Kconfig circular dependency issues.
Therefore, change the use of "depends on" for IRQ_DOMAIN to
"select" for RTC_DRV_MT6397.
Fixes: 04d3ba70a3c9 ("rtc: mt6397: add IRQ domain dependency") Cc: Arnd Bergmann <arnd@arndb.de> Cc: Eddie Huang <eddie.huang@mediatek.com> Cc: Sean Wang <sean.wang@mediatek.com> Cc: Matthias Brugger <matthias.bgg@gmail.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-mediatek@lists.infradead.org Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: linux-rtc@vger.kernel.org Cc: Marc Zyngier <maz@kernel.org> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Peter Rosin <peda@axentia.se> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Link: https://lore.kernel.org/r/20240213050258.6167-1-rdunlap@infradead.org Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When perf_init_event() calls perf_try_init_event() to init pmu driver,
searches for the next pmu driver only when the return value is -ENOENT.
Therefore, hisi_ptt_pmu_event_init() needs to check the type at the
beginning of the function.
Otherwise, in the case of perf-task mode, perf_try_init_event() returns
-EOPNOTSUPP and skips subsequent pmu drivers, causes perf_init_event() to
fail.
Fixes: ff0de066b463 ("hwtracing: hisi_ptt: Add trace function support for HiSilicon PCIe Tune and Trace device") Signed-off-by: Yang Jihong <yangjihong1@huawei.com> Reviewed-by: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20240108121906.3514820-1-yangjihong1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The loop based 64bit division may run for a long time when dividend is a
lot bigger than the divider. Replace the division loop by the
div64_u64() which implementation may be significantly faster.
skip_power_up is used in etm4_init_arch_data when set lpoverride. So
need to set the value of it before calling using it.
Fixes: 5214b563588e ("coresight: etm4x: Add support for sysreg only devices") Signed-off-by: Mao Jinlong <quic_jinlmao@quicinc.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20240131105423.9519-1-quic_jinlmao@quicinc.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The linked commit reverts the change that accidentally used some sysfs
enable/disable functions from Perf which broke the refcounting, but it
also removes the fact that the sysfs disable function disabled the
helpers.
Add a new wrapper function that does both which is used by both Perf and
sysfs, and label the sysfs disable function appropriately. The naming of
all of the functions will be tidied up later to avoid this happening
again.
Fixes: 287e82cf69aa ("coresight: Fix crash when Perf and sysfs modes are used concurrently") Signed-off-by: James Clark <james.clark@arm.com> Link: https://lore.kernel.org/r/20240129154050.569566-2-james.clark@arm.com Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ethernet switch does not have addressable subnodes.
This fixes:
arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-asus-gt-ac5300.dtb: ethernet-switch@0: '#address-cells', '#size-cells' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/net/dsa/brcm,sf2.yaml#
The core expects for tx_empty() either TIOCSER_TEMT when the tx is
empty or 0 otherwise. s3c24xx_serial_txempty_nofifo() might return
0x4, and at least uart_get_lsr_info() tries to clear exactly
TIOCSER_TEMT (BIT(1)). Fix tx_empty() to return TIOCSER_TEMT.
The if (c >= 20 && c <= 0x3f) test added in commit 7a99565f8732 is
wrong. 20 is DC4 in ascii and it makes no sense to consider that as the
bottom limit. Instead, it should be 0x20 as in the other test in
the commit above. This is supposed to NOT change anything as we handle
interesting 20-0x20 asciis far before this if.
While support for working with a vbus was added, the regulator was never
actually gotten (despite what was documented). Fix this by actually
getting the supply from the device tree.
Fix off-by-one error in transfer-function property.
The honeywell,transfer-function property takes values between 1-3 so
make sure the proper enum gets used.
Fixes: 713337d9143ed ("iio: pressure: Honeywell mprls0025pa pressure sensor") Co-developed-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Andreas Klinger <ak@it-klinger.de> Signed-off-by: Petre Rodan <petre.rodan@subdimension.ro> Link: https://lore.kernel.org/r/20231229092445.30180-5-petre.rodan@subdimension.ro Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sparse tool complains about the remove of the _iomem attribute.
stm32_rproc.c:660:17: warning: cast removes address space '__iomem' of expression
Add '__force' to explicitly specify that the cast is intentional.
This conversion is necessary to cast to addresses pointer,
which are then managed by the remoteproc core as a pointer to a
resource_table structure.
Add '__force' to explicitly specify that the cast is intentional.
This conversion is necessary to cast to virtual addresses pointer,used,
by the remoteproc core.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202312150052.HCiNKlqB-lkp@intel.com/ Fixes: 13140de09cc2 ("remoteproc: stm32: add an ST stm32_rproc driver") Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com> Link: https://lore.kernel.org/r/20240117135312.3381936-2-arnaud.pouliquen@foss.st.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On Arrow Lake S systems, MEI is no longer strictly connected to bus 0,
while graphics remain exclusively on bus 0. Adapt the component
matching logic to accommodate this change:
Original behavior: Required both MEI and graphics to be on the same
bus 0.
New behavior: Only enforces graphics to be on bus 0 (integrated),
allowing MEI to reside on any bus.
This ensures compatibility with Arrow Lake S and maintains functionality
for the legacy systems.
The comedi_test devices have a couple of timers (ai_timer and ao_timer)
that can be started to simulate hardware interrupts. Their expiry
functions normally reschedule the timer. The driver code calls either
del_timer_sync() or del_timer() to delete the timers from the queue, but
does not currently prevent the timers from rescheduling themselves so
synchronized deletion may be ineffective.
Add a couple of boolean members (one for each timer: ai_timer_enable and
ao_timer_enable) to the device private data structure to indicate
whether the timers are allowed to reschedule themselves. Set the member
to true when adding the timer to the queue, and to false when deleting
the timer from the queue in the waveform_ai_cancel() and
waveform_ao_cancel() functions.
The del_timer_sync() function is also called from the waveform_detach()
function, but the timer enable members will already be set to false when
that function is called, so no change is needed there.
Inspecting the core with drgn I was able to pull this
>>> prog.crashed_thread().stack_trace()[0]
#0 at 0xffffffffa079657a (ff_layout_cancel_io+0x3a/0x84) in ff_layout_cancel_io at fs/nfs/flexfilelayout/flexfilelayout.c:2021:27
>>> prog.crashed_thread().stack_trace()[0]['idx']
(u32)1
>>> prog.crashed_thread().stack_trace()[0]['flseg'].mirror_array[1].mirror_ds
(struct nfs4_ff_layout_ds *)0xffffffffffffffed
This is clear from the stack trace, we call nfs4_ff_layout_prepare_ds()
which could error out initializing the mirror_ds, and then we go to
clean it all up and our check is only for if (!mirror->mirror_ds). This
is inconsistent with the rest of the users of mirror_ds, which have
if (IS_ERR_OR_NULL(mirror_ds))
to keep from tripping over this exact scenario. Fix this up in
ff_layout_cancel_io() to make sure we don't panic when we get an error.
I also spot checked all the other instances of checking mirror_ds and we
appear to be doing the correct checks everywhere, only unconditionally
dereferencing mirror_ds when we know it would be valid.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Fixes: b739a5bd9d9f ("NFSv4/flexfiles: Cancel I/O if the layout is recalled or revoked") Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When bringing a CPU online, some of the PMC and LBR related registers
are reset. The same is done when a CPU is taken offline although that
is unnecessary. This currently happens in the "cpu_dead" callback which
is also incorrect as the callback runs on a control CPU instead of the
one that is being taken offline. This also affects hibernation and
suspend to RAM on some platforms as reported in the link below.
Fixes: 21d59e3e2c40 ("perf/x86/amd/core: Detect PerfMonV2 support") Reported-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Sandipan Das <sandipan.das@amd.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/550a026764342cf7e5812680e3e2b91fe662b5ac.1706526029.git.sandipan.das@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Thread A GC thread
- gc_data_segment
- ra_data_block
- locked meta_inode page
- f2fs_inplace_write_data
- invalidate_mapping_pages
: fail to invalidate meta_inode page
due to lock failure or dirty|writeback
status
- f2fs_submit_page_bio
: write last dirty data to old blkaddr
- move_data_block
- load old data from meta_inode page
- f2fs_submit_page_write
: write old data to new blkaddr
Because invalidate_mapping_pages() will skip invalidating page which
has unclear status including locked, dirty, writeback and so on, so
we need to use truncate_inode_pages_range() instead of
invalidate_mapping_pages() to make sure meta_inode page will be dropped.
Fixes: 6aa58d8ad20a ("f2fs: readahead encrypted block during GC") Fixes: e3b49ea36802 ("f2fs: invalidate META_MAPPING before IPU/DIO write") Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is because the file has only one direct_node. After returning
to -ENOSPC, reserved_blocks += ret will not be executed. As a result,
the reserved_blocks at this time is still 0, which is not the real
number of reserved blocks. Therefore, fsck cannot be set to repair
the file.
After this patch, the fsck flag will be set to fix this problem.
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 1.8M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
F2FS_IOC_RESERVE_COMPRESS_BLOCKS failed: No space left on device
adb reboot then fsck will be executed
unisoc # df -h | grep dm-48
/dev/block/dm-48 112G 112G 11M 100% /data
unisoc # ./f2fs_io reserve_cblocks test.apk
924
The following f2fs_io test will get a "0" result instead of -EINVAL,
unisoc # ./f2fs_io compress file
unisoc # ./f2fs_io reserve_cblocks file
0
it's not reasonable, so the judgement of
atomic_read(&F2FS_I(inode)->i_compr_blocks) should be placed after
the judgement of is_inode_flag_set(inode, FI_COMPRESS_RELEASED).
Currently, even though xprtsec=tls is specified and used for operations
to MDS, any operations that go to DS travel over unencrypted connection.
Or additionally, if more than 1 DS can serve the data, then trunked
connections are also done unencrypted.
IN GETDEVINCEINFO, we get an entry for the DS which carries a protocol
type (which is TCP), then nfs4_set_ds_client() gets called with TCP
instead of TCP with TLS.
Currently, each trunked connection is created and uses clp->cl_hostname
value which if TLS is used would get passed up in the handshake upcall,
but instead we need to pass in the appropriate trunked address value.
Fixes: c8407f2e560c ("NFS: Add an "xprtsec=" NFS mount option") Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The intent is to check if 'dest' is truncated or not. So, >= should be
used instead of >, because strlcat() returns the length of 'dest' and 'src'
excluding the trailing NULL.
Fixes: 56463e50d1fc ("NFS: Use super.c for NFSROOT mount option parsing") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The loop inside nfs_netfs_issue_read() currently does not disable
interrupts while iterating through pages in the xarray to submit
for NFS read. This is not safe though since after taking xa_lock,
another page in the mapping could be processed for writeback inside
an interrupt, and deadlock can occur. The fix is simple and clean
if we use xa_for_each_range(), which handles the iteration with RCU
while reducing code complexity.
The problem is easily reproduced with the following test:
mount -o vers=3,fsc 127.0.0.1:/export /mnt/nfs
dd if=/dev/zero of=/mnt/nfs/file1.bin bs=4096 count=1
echo 3 > /proc/sys/vm/drop_caches
dd if=/mnt/nfs/file1.bin of=/dev/null
umount /mnt/nfs
On the console with a lockdep-enabled kernel a message similar to
the following will be seen:
================================
WARNING: inconsistent lock state
6.7.0-lockdbg+ #10 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
test5/1708 [HC0[0]:SC0[0]:HE1:SE1] takes: ffff888127baa598 (&xa->xa_lock#4){+.?.}-{3:3}, at:
nfs_netfs_issue_read+0x1b2/0x4b0 [nfs]
{IN-SOFTIRQ-W} state was registered at:
lock_acquire+0x144/0x380
_raw_spin_lock_irqsave+0x4e/0xa0
__folio_end_writeback+0x17e/0x5c0
folio_end_writeback+0x93/0x1b0
iomap_finish_ioend+0xeb/0x6a0
blk_update_request+0x204/0x7f0
blk_mq_end_request+0x30/0x1c0
blk_complete_reqs+0x7e/0xa0
__do_softirq+0x113/0x544
__irq_exit_rcu+0xfe/0x120
irq_exit_rcu+0xe/0x20
sysvec_call_function_single+0x6f/0x90
asm_sysvec_call_function_single+0x1a/0x20
pv_native_safe_halt+0xf/0x20
default_idle+0x9/0x20
default_idle_call+0x67/0xa0
do_idle+0x2b5/0x300
cpu_startup_entry+0x34/0x40
start_secondary+0x19d/0x1c0
secondary_startup_64_no_verify+0x18f/0x19b
irq event stamp: 176891
hardirqs last enabled at (176891): [<ffffffffa67a0be4>]
_raw_spin_unlock_irqrestore+0x44/0x60
hardirqs last disabled at (176890): [<ffffffffa67a0899>]
_raw_spin_lock_irqsave+0x79/0xa0
softirqs last enabled at (176646): [<ffffffffa515d91e>]
__irq_exit_rcu+0xfe/0x120
softirqs last disabled at (176633): [<ffffffffa515d91e>]
__irq_exit_rcu+0xfe/0x120
other info that might help us debug this:
Possible unsafe locking scenario:
Fixes: 000dbe0bec05 ("NFS: Convert buffered read paths to use netfs when fscache is enabled") Suggested-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Dave Wysochanski <dwysocha@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: David Howells <dhowells@redhat.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log