This patch fixes negative indexing of buf array in pin_assignment_show
when get_current_pin_assignments returns 0 i.e. no compatible pin
assignments are found.
The CDC-ECM specification [1] requires to send the host MAC address as
an uppercase hexadecimal string in chapter "5.4 Ethernet Networking
Functional Descriptor":
The Unicode character is chosen from the set of values 30h through
39h and 41h through 46h (0-9 and A-F).
However, snprintf(.., "%pm", ..) generates a lowercase MAC address
string. While most host drivers are tolerant to this, UsbNcm.sys on
Windows 10 is not. Instead it uses a different MAC address with all
bytes set to zero including and after the first byte containing a
lowercase letter. On Windows 11 Microsoft fixed it, but apparently they
did not backport the fix.
This change fixes the issue by upper-casing the MAC to comply with the
specification.
When the dwc3 device is runtime suspended, various required clocks are in
disabled state and it is not guaranteed that access to any registers would
work. Depending on the SoC glue, a register read could be as benign as
returning 0 or be fatal enough to hang the system.
In order to prevent such scenarios of fatal errors, make sure to resume
dwc3 then allow the function to proceed.
Prevent -ETIMEDOUT error on .suspend().
e.g. If gadget driver is loaded and we are connected to a USB host,
all transfers must be stopped before stopping the controller else
we will not get a clean stop i.e. dwc3_gadget_run_stop() will take
several seconds to complete and will return -ETIMEDOUT.
Handle error cases properly in dwc3_gadget_suspend().
Simplify dwc3_gadget_resume() by using the introduced helper function.
OverCurrent condition is not standardized in the UHCI spec.
Zhaoxin UHCI controllers report OverCurrent bit active off.
In order to handle OverCurrent condition correctly, the uhci-hcd
driver needs to be told to expect the active-off behavior.
Suggested-by: Alan Stern <stern@rowland.harvard.edu> Cc: stable@vger.kernel.org Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20230423105952.4526-1-WeitaoWang-oc@zhaoxin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With faulty usb-storage devices, read/write can timeout, in that case
the SCSI layer will abort and re-issue the command. USB storage has no
internal timeout, it relies on SCSI layer aborting commands via
.eh_abort_handler() for non those responsive devices.
After two consecutive timeouts of the same command, SCSI layer calls
.eh_device_reset_handler(), without calling .eh_abort_handler() first.
The syzbot fuzzer found a problem in the usbtmc driver: When a user
submits an ioctl for a 0-length control transfer, the driver does not
check that the direction is set to OUT:
Line6 Pod Go (0e41:424b) requires the similar workaround for the fixed
48k sample rate like other Line6 models. This patch adds the
corresponding entry to line6_parse_audio_format_rate_quirk().
When CONFIG_BRIDGE_VLAN_FILTERING is disabled, two functions are still
defined but have no prototype or caller. This causes a W=1 warning for
the missing prototypes:
net/bridge/br_netlink_tunnel.c:29:6: error: no previous prototype for 'vlan_tunid_inrange' [-Werror=missing-prototypes]
net/bridge/br_netlink_tunnel.c:199:5: error: no previous prototype for 'br_vlan_tunnel_info' [-Werror=missing-prototypes]
The functions are already contitional on CONFIG_BRIDGE_VLAN_FILTERING,
and I coulnd't easily figure out the right set of #ifdefs, so just
move the declarations out of the #ifdef to avoid the warning,
at a small cost in code size over a more elaborate fix.
Fixes: 188c67dd1906 ("net: bridge: vlan options: add support for tunnel id dumping") Fixes: 569da0822808 ("net: bridge: vlan options: add support for tunnel mapping set/del") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230516194625.549249-3-arnd@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is no guarantee that rb_prev() will not return NULL in nft_rbtree_gc_elem():
general protection fault, probably for non-canonical address 0xdffffc0000000003: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000018-0x000000000000001f]
nft_add_set_elem+0x14b0/0x2990
nf_tables_newsetelem+0x528/0xb30
Furthermore, there is a possible use-after-free while iterating,
'node' can be free'd so we need to cache the next value to use.
Fixes: c9e6978e2725 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
nft_trans_FOO objects all share a common nft_trans base structure, but
trailing fields depend on the real object size. Access is only safe after
trans->msg_type check.
Check for rule type first. Found by code inspection.
The cited commit added a stray colon to the 'v' option. That makes the
option work incorrectly.
ex:
tools/testing/selftests/net# ./fib_nexthops.sh -v
(should enable verbose mode, instead it shows help text due to missing arg)
Fixes: 5feba4727395 ("selftests: fib_nexthops: Make ping timeout configurable") Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The XPCS expects clause 73 (copper backplane) autoneg to follow the
ethtool autoneg bit. It actually did that until the blamed
commit inaptly replaced state->an_enabled (coming from ethtool) with
phylink_autoneg_inband() (coming from the device tree or struct
phylink_config), as part of an unrelated phylink_pcs API conversion.
Russell King suggests that state->an_enabled from the original code was
just a proxy for the ethtool Autoneg bit, and that the correct way of
restoring the functionality is to check for this bit in the advertising
mask.
Fixes: 11059740e616 ("net: pcs: xpcs: convert to phylink_pcs_ops") Link: https://lore.kernel.org/netdev/ZGNt2MFeRolKGFck@shell.armlinux.org.uk/ Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In suspend and resume cycle, the removal and rescan of device ends
up in NULL pointer dereference.
During driver initialization, if the ipc_imem_wwan_channel_init()
fails to get the valid device capabilities it returns an error and
further no resource (wwan struct) will be allocated. Now in this
situation if driver removal procedure is initiated it would result
in NULL pointer exception since unallocated wwan struct is dereferenced
inside ipc_wwan_deinit().
ipc_imem_run_state_worker() to handle the called functions return value
and to release the resource in failure case. It also reports the link
down event in failure cases. The user space application can handle this
event to do a device reset for restoring the device communication.
Fixes: 3670970dd8c6 ("net: iosm: shared memory IPC interface") Reported-by: Samuel Wein PhD <sam@samwein.com> Closes: https://lore.kernel.org/netdev/20230427140819.1310f4bd@kernel.org/T/ Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
CPU: 0 PID: 29770 Comm: syz-executor.0 Not tainted 6.3.0-rc6-syzkaller-gc478e5b17829 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/30/2023
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In igb_hash_mc_addr() the expression:
"mc_addr[4] >> 8 - bit_shift", right shifting "mc_addr[4]"
shift by more than 7 bits always yields zero, so hash becomes not so different.
Add initialization with bit_shift = 1 and add a loop condition to ensure
bit_shift will be always in [1..8] range.
Fixes: 9d5c824399de ("igb: PCI-Express 82575 Gigabit Ethernet driver") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to datasheet, the command opcode must be specified
into bits [14:12] of the Extended Port Control register (EPC).
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family") Signed-off-by: Marco Migliore <m.migliore@tiesse.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
cas_saturn_firmware_init() allocates some memory using vmalloc(). This
memory is freed in the .remove() function but not it the error handling
path of the probe.
Add the missing vfree() to avoid a memory leak, should an error occur.
Fixes: fcaa40669cd7 ("cassini: use request_firmware") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we enable NAPI and multi-queue on a TUN device, we can put skb into
tfile->sk.sk_write_queue after the queue is detached. We should prevent
it by checking tfile->detached before queuing skb.
Note this must be done under tfile->sk.sk_write_queue.lock because write()
and ioctl(IFF_DETACH_QUEUE) can run concurrently. Otherwise, there would
be a small race window:
Another solution is to call tun_queue_purge() when closing and
reattaching the detached queue, but it could paper over another
problems. Also, we do the same kind of test for IFF_NAPI_FRAGS.
Fixes: cde8b15f1aab ("tuntap: add ioctl to attach or detach a file form tuntap device") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
'__net_initdata' becomes a no-op with CONFIG_NET_NS=y, but when this
option is disabled it becomes '__initdata', which means the data can be
freed after the initialization phase. This annotation is obviously
incorrect for the devlink net device notifier block which is still
registered after the initialization phase [1].
Fix this crash by removing the '__net_initdata' annotation.
In a SCSI request, storvsc pre-allocates space for up to
MAX_PAGE_BUFFER_COUNT physical frame numbers to be passed to Hyper-V. If
the size of the I/O request requires more PFNs, a separate memory area of
exactly the correct size is dynamically allocated.
But when the pre-allocated area is used, current code always passes
MAX_PAGE_BUFFER_COUNT PFNs to Hyper-V, even if fewer are needed. While
this doesn't break anything because the additional PFNs are always zero,
more bytes than necessary are copied into the VMBus channel ring buffer.
This takes CPU cycles and wastes space in the ring buffer. For a typical 4
Kbyte I/O that requires only a single PFN, 248 unnecessary bytes are
copied.
Fix this by setting the payload_sz based on the actual number of PFNs
required, not the size of the pre-allocated space.
Reported-by: John Starks <jostarks@microsoft.com> Fixes: 8f43710543ef ("scsi: storvsc: Support PAGE_SIZE larger than 4K") Signed-off-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/1684171241-16209-1-git-send-email-mikelley@microsoft.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the firmware sends us a corrupted MCC response with
n_channels much larger than the command response can be,
we might copy far too much (uninitialized) memory and
even crash if the n_channels is large enough to make it
run out of the one page allocated for the FW response.
Fix that by checking the lengths. Doing a < comparison
would be sufficient, but the firmware should be doing
it correctly, so check more strictly.
The DBGI dump is (unsurprisingly) of type DBGI, not SRAM.
This leads to bad register accesses because the union is
built differently, there's no allocation ID, and thus the
allocation ID ends up being 0x8000.
Note that this was already wrong for DRAM vs. SMEM since
they use different parts of the union, but the allocation
ID is at the same place, so it worked.
Fix all of this but set the allocation ID in a way that
the offset calculation ends up without any offset.
Lockdep points out that we can deadlock here by calling
cancel_delayed_work_sync() because that might be already
running and gotten interrupted by the NAPI soft-IRQ.
Even just calling something that can sleep is wrong in
this context though.
Luckily, it doesn't even really matter since the things
we need to do are idempotent, so just drop the _sync().
When stopping the AP, there might be a color change in progress. It
should be deactivated here, or the driver might later finalize a color
change on a stopped AP.
Fixes: 5f9404abdf2a (mac80211: add support for BSS color change) Signed-off-by: Michael Lee <michael-cy.lee@mediatek.com> Link: https://lore.kernel.org/r/20230504080441.22958-1-michael-cy.lee@mediatek.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to set the correct trace variable, otherwise we're
overwriting something else instead and the right one that
we print later is not initialized.
Fixes: b6011960f392 ("mac80211: handle channel frequency offset") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/20230504134511.828474-2-gregory.greenman@intel.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
'changed' can be OR'ed with BSS_CHANGED_EHT_PUNCTURING which is larger than
an u32.
So, turn 'changed' into an u64 and update ieee80211_set_after_csa_beacon()
accordingly.
In the commit in Fixes, only ieee80211_start_ap() was updated.
However small the chance (increased by ftracetest), an asynchronous
interrupt can occur in between of spin_lock() and spin_unlock(),
and the interrupt routine will attempt to lock the same
&local->queue_stop_reason_lock again.
This will cause a costly reset of the CPU and the wifi device or an
altogether hang in the single CPU and single core scenario.
The only remaining spin_lock(&local->queue_stop_reason_lock) that
did not disable interrupts was patched, which should prevent any
deadlocks on the same CPU/core and the same wifi device.
When the user disables rxvlan offloading and then changes the number of
channels, all VLAN ports are unable to receive traffic.
Changing the number of channels triggers a VFR reset. During re-init, when
VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is received, we do:
1 - set the IAVF_FLAG_SETUP_NETDEV_FEATURES flag
2 - call
iavf_set_vlan_offload_features(adapter, 0, netdev->features);
The second step sends to the PF the __default__ features, in this case
aq_required |= IAVF_FLAG_AQ_ENABLE_CTAG_VLAN_STRIPPING
While the first step forces the watchdog task to call
netdev_update_features() -> iavf_set_features() ->
iavf_set_vlan_offload_features(adapter, netdev->features, features).
Since the user disabled the "rxvlan", this sets:
aq_required |= IAVF_FLAG_AQ_DISABLE_CTAG_VLAN_STRIPPING
When we start processing the AQ commands, both flags are enabled. Since we
process DISABLE_XTAG first then ENABLE_XTAG, this results in the PF
enabling the rxvlan offload. This breaks all communications on the VLAN
net devices.
Fix by removing the call to iavf_set_vlan_offload_features() (second
step). Calling netdev_update_features() from watchdog task is enough for
both init and reset paths.
Fixes: 7598f4b40bd6 ("iavf: Move netdev_update_features() into watchdog task") Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This leads to a series of -53 errors
(failed to init adminq) from the IAVF.
Change the state of the vf_state field to be not active when the IAVF
is still initializing. Make sure to wait until receiving the message on
the message box to ensure that the vf is ready and initializded.
In simple terms we use the ACTIVE flag to make sure that the ice
driver knows if the iavf is ready for another reset
After a core PF reset, the VFs were showing wrong Rx/Tx stats. This is a
regression in commit 6624e780a577 ("ice: split ice_vsi_setup into smaller
functions") caused by missing to set "stat_offsets_loaded = false" in the
ice_vsi_rebuild() path.
Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions") Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Removing the phy_stop() from bcmgenet_netif_stop() ended up causing
warnings from the PHY library that phy_start() is called from the
RUNNING state since we are no longer stopping the PHY state machine
during bcmgenet_suspend().
Restore the call to phy_stop() but make it conditional on being called
from the close or suspend path.
Fixes: c96e731c93ff ("net: bcmgenet: connect and disconnect from the PHY state machine") Fixes: 93e0401e0fc0 ("net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Link: https://lore.kernel.org/r/20230515025608.2587012-1-f.fainelli@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to phy_stop() races with the later call to phy_disconnect(),
resulting in concurrent phy_suspend() calls being run from different
CPUs. The final call to phy_disconnect() ensures that the PHY is
stopped and suspended, too.
Fixes: c96e731c93ff ("net: bcmgenet: connect and disconnect from the PHY state machine") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 225c657945c4 ("net: bcmgenet: Restore phy_stop() depending upon suspend/close") Signed-off-by: Sasha Levin <sashal@kernel.org>
can_put_echo_skb() checks for the enabled IFF_ECHO flag and the
correct ETH_P type of the given skbuff. When implementing the CAN XL
support the new check for ETH_P_CANXL has been forgotten.
Fixes: fb08cba12b52 ("can: canxl: update CAN infrastructure for CAN XL frames") Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/all/20230506184515.39241-1-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently when the new channel-path is enabled, we do evaluation only
on the subchannels with a device connected on it. This is because,
in the past, if the device in the subchannel is not working or not
available, we used to unregister the subchannels. But, from the 'commit 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers")'
we allow subchannels with or without an active device connected
on it. So, when we do the io_subchannel_verify, make sure that,
we are evaluating the subchannels without any device too.
Fixes: 2297791c92d0 ("s390/cio: dont unregister subchannel from child-drivers") Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com> Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Checking the bearer min mtu with tipc_udp_mtu_bad() only works for
IPv4 UDP bearer, and IPv6 UDP bearer has a different value for the
min mtu. This patch checks with encap_hlen + TIPC_MIN_BEARER_MTU
for min mtu, which works for both IPv4 and IPv6 UDP bearer.
Note that tipc_udp_mtu_bad() is still used to check media min mtu
in __tipc_nl_media_set(), as m->mtu currently is only used by the
IPv4 UDP bearer as its default mtu value.
Fixes: 682cd3cf946b ("tipc: confgiure and apply UDP bearer MTU on running links") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When doing link mtu negotiation, a malicious peer may send Activate msg
with a very small mtu, e.g. 4 in Shuang's testing, without checking for
the minimum mtu, l->mtu will be set to 4 in tipc_link_proto_rcv(), then
n->links[bearer_id].mtu is set to 4294967228, which is a overflow of
'4 - INT_H_SIZE - EMSG_OVERHEAD' in tipc_link_mss().
With tipc_link.mtu = 4, tipc_link_xmit() kept printing the warning:
tipc: Too large msg, purging xmit list 1 5 0 40 4!
tipc: Too large msg, purging xmit list 1 15 0 60 4!
And with tipc_link_entry.mtu 4294967228, a huge skb was allocated in
named_distribute(), and when purging it in tipc_link_xmit(), a crash
was even caused:
This patch fixes it by checking the new mtu against tipc_bearer_min_mtu(),
and not updating mtu if it is too small.
Fixes: ed193ece2649 ("tipc: simplify link mtu negotiation") Reported-by: Shuang Li <shuali@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As different media may requires different min mtu, and even the
same media with different net family requires different min mtu,
add tipc_bearer_min_mtu() to calculate min mtu accordingly.
This API will be used to check the new mtu when doing the link
mtu negotiation in the next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 56077b56cd3f ("tipc: do not update mtu if msg_max is too small in mtu negotiation") Signed-off-by: Sasha Levin <sashal@kernel.org>
When initializing XDP in virtnet_open(), some rq xdp initialization
may hit an error causing net device open failed. However, previous
rqs have already initialized XDP and enabled NAPI, which is not the
expected behavior. Need to roll back the previous rq initialization
to avoid leaks in error unwinding of init code.
Also extract helper functions of disable and enable queue pairs.
Use newly introduced disable helper function in error unwinding and
virtnet_close. Use enable helper function in virtnet_open.
Fixes: 754b8a21a96d ("virtio_net: setup xdp_rxq_info") Signed-off-by: Feng Liu <feliu@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: William Tu <witu@nvidia.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the implementation, the sent_frame count does not increment when
transmit errors occur. Therefore, bq_xmit_all() will take care of
returning the XDP frames.
Fixes: 26312c685ae0 ("net: fec: correct the counting of XDP sent frames") Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
The empty stub functions are defined as global functions, which
causes a warning because of missing prototypes:
drivers/gpu/drm/exynos/exynos_drm_g2d.h:37:5: error: no previous prototype for 'g2d_open'
drivers/gpu/drm/exynos/exynos_drm_g2d.h:42:5: error: no previous prototype for 'g2d_close'
Mark them as 'static inline' to avoid the warning and to make
them behave as intended.
Topology could have more instances of the tokens being searched for than
the number of sets that need to be copied. Stop copying token after the
limit of number of token instances has been reached. This worked before
only by chance as we had allocated more size for the tuples array than
the number of actual tokens being parsed.
Fixes: 7006d20e5e9d ("ASoC: SOF: Introduce IPC3 ops") Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Link: https://lore.kernel.org/r/20230512114630.24439-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
When devm runs function in the "remove" path for a device it runs them
in the reverse order. That means that if you have parts of your driver
that aren't using devm or are using "roll your own" devm w/
devm_add_action_or_reset() you need to keep that in mind.
The mt8186 audio driver didn't quite get this right. Specifically, in
mt8186_init_clock() it called mt8186_audsys_clk_register() and then
went on to call a bunch of other devm function. The caller of
mt8186_init_clock() used devm_add_action_or_reset() to call
mt8186_deinit_clock() but, because of the intervening devm functions,
the order was wrong.
Specifically at probe time, the order was:
1. mt8186_audsys_clk_register()
2. afe_priv->clk = devm_kcalloc(...)
3. afe_priv->clk[i] = devm_clk_get(...)
At remove time, the order (which should have been 3, 2, 1) was:
1. mt8186_audsys_clk_unregister()
3. Free all of afe_priv->clk[i]
2. Free afe_priv->clk
The above seemed to be causing a use-after-free. Luckily, it's easy to
fix this by simply using devm more correctly. Let's move the
devm_add_action_or_reset() to the right place. In addition to fixing
the use-after-free, code inspection shows that this fixes a leak
(missing call to mt8186_audsys_clk_unregister()) that would have
happened if any of the syscon_regmap_lookup_by_phandle() calls in
mt8186_init_clock() had failed.
The commands in sof_ipc_dai_config.flags are encoded as bits:
1 (bit0) - hw_params
2 (bit1) - hw_free
4 (bit2) - pause
These are commands, they cannot be combined as one would assume, for
example
3 (bit0 | bit1) is invalid.
This can happen right at the second start of a stream as at the end of the
first stream we set the hw_free command (bit1) and on the second start we
would OR on top of it the hw_params (bit0).
Fixes: b66bfc3a9810 ("ASoC: SOF: sof-audio: Fix broken early bclk feature for SSP") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com Link: https://lore.kernel.org/r/20230512110317.5180-1-peter.ujfalusi@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the ->xprt_ctxt pointer was added to svc_deferred_req, it has not
been sufficient to use kfree() to free a deferred request. We may need
to free the ctxt as well.
As freeing the ctxt is all that ->xpo_release_rqst() does, we repurpose
it to explicit do that even when the ctxt is not stored in an rqst.
So we now have ->xpo_release_ctxt() which is given an xprt and a ctxt,
which may have been taken either from an rqst or from a dreq. The
caller is now responsible for clearing that pointer after the call to
->xpo_release_ctxt.
We also clear dr->xprt_ctxt when the ctxt is moved into a new rqst when
revisiting a deferred request. This ensures there is only one pointer
to the ctxt, so the risk of double freeing in future is reduced. The
new code in svc_xprt_release which releases both the ctxt and any
rq_deferred depends on this.
Fixes: 773f91b2cf3f ("SUNRPC: Fix NFSD's request deferral on RDMA transports") Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an RPC request is deferred, the rq_xprt_ctxt pointer is moved out
of the svc_rqst into the svc_deferred_req.
When the deferred request is revisited, the pointer is copied into
the new svc_rqst - and also remains in the svc_deferred_req.
In the (rare?) case that the request is deferred a second time, the old
svc_deferred_req is reused - it still has all the correct content.
However in that case the rq_xprt_ctxt pointer is NOT cleared so that
when xpo_release_xprt is called, the ctxt is freed (UDP) or possible
added to a free list (RDMA).
When the deferred request is revisited for a second time, it will
reference this ctxt which may be invalid, and the free the object a
second time which is likely to oops.
So change svc_defer() to *always* clear rq_xprt_ctxt, and assert that
the value is now stored in the svc_deferred_req.
Fixes: 773f91b2cf3f ("SUNRPC: Fix NFSD's request deferral on RDMA transports") Signed-off-by: NeilBrown <neilb@suse.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When Universal DVB card is detaching, netup_unidvb_dma_fini()
uses del_timer() to stop dma->timeout timer. But when timer
handler netup_unidvb_dma_timeout() is running, del_timer()
could not stop it. As a result, the use-after-free bug could
happen. The process is shown below:
The timeout of the cmdq reset command has been increased to
resolve the reset timeout issue in the full VF scenario.
The timeout of other cmdq commands remains unchanged.
Fixes: 8d307f8e8cf1 ("net: hns3: create new set of unified hclge_comm_cmd_send APIs") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the hns3 vf function reset delays 5000ms before vf rebuild
process. In product applications, this delay is too long for application
configurations and causes configuration timeout.
According to the tests, 500ms delay is enough for reset process except PF
FLR. So this patch modifies delay to 500ms in these scenarios.
Fixes: 6988eb2a9b77 ("net: hns3: Add support to reset the enet/ring mgmt layer") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
To prevent the system from abnormally sending PFC frames after an
abnormal reset. The hns3 driver notifies the firmware to disable pfc
before reset.
Fixes: 35d93a30040c ("net: hns3: adjust the process of PF reset") Signed-off-by: Jijie Shao <shaojijie@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In function hns3_dump_tx_queue_info, The print buffer is not enough when
the tx BD number is configured to 32760. As a result several BD
information wouldn't be displayed.
So fix it by increasing the tx queue print buffer length.
Fixes: 630a6738da82 ("net: hns3: adjust string spaces of some parameters of tx bd info in debugfs") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Hao Lan <lanhao@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When ports are in standalone mode, they should have learning disabled to
avoid adding new entries in the MAC lookup table which might be used by
other bridge ports to forward packets. While adding that, also make sure
learning is enabled for CPU port.
Fixes: 888cdb892b61 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver") Signed-off-by: Clément Léger <clement.leger@bootlin.com> Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
stp_set_state() should actually allow receiving BPDU while in LEARNING
mode which is not the case. Additionally, the BLOCKEN bit does not
actually forbid sending forwarded frames from that port. To fix this, add
a5psw_port_tx_enable() function which allows to disable TX. However, while
its name suggest that TX is totally disabled, it is not and can still
allow to send BPDUs even if disabled. This can be done by using forced
forwarding with the switch tagging mechanism but keeping "filtering"
disabled (which is already the case in the rzn1-a5sw tag driver). With
these fixes, STP support is now functional.
Fixes: 888cdb892b61 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver") Signed-off-by: Clément Léger <clement.leger@bootlin.com> Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, management frame were discarded before reaching the CPU port due
to a misconfiguration of the MGMT_CONFIG register. Enable them by setting
the correct value in this register in order to correctly receive management
frame and handle STP.
Fixes: 888cdb892b61 ("net: dsa: rzn1-a5psw: add Renesas RZ/N1 advanced 5 port switch driver") Signed-off-by: Clément Léger <clement.leger@bootlin.com> Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com> Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 20704bd1633d ("erspan: build the header with the right proto
according to erspan_ver"), it gets the proto with t->parms.erspan_ver,
but t->parms.erspan_ver is not used by collect_md branch, and instead
it should get the proto with md->version for collect_md.
Thanks to Kevin for pointing this out.
Fixes: 20704bd1633d ("erspan: build the header with the right proto according to erspan_ver") Fixes: 94d7d8f29287 ("ip6_gre: add erspan v2 support") Reported-by: Kevin Traynor <ktraynor@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch reports:
drivers/tty/serial/8250/8250_bcm7271.c:1120 brcmuart_probe() warn:
'baud_mux_clk' from clk_prepare_enable() not released on lines: 1032.
When tcp_v4_send_reset() is called with @sk == NULL,
we do not change ctl_sk->sk_priority, which could have been
set from a prior invocation.
Change tcp_v4_send_reset() to set sk_priority and sk_mark
fields before calling ip_send_unicast_reply().
This means tcp_v4_send_reset() and tcp_v4_send_ack()
no longer have to clear ctl_sk->sk_mark after
their call to ip_send_unicast_reply().
Fixes: f6c0f5d209fa ("tcp: honor SO_PRIORITY in TIME_WAIT state") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When client and server establish a connection through vsock,
the client send a request to the server to initiate the connection,
then start a timer to wait for the server's response. When the server's
RESPONSE message arrives, the timer also times out and exits. The
server's RESPONSE message is processed first, and the connection is
established. However, the client's timer also times out, the original
processing logic of the client is to directly set the state of this vsock
to CLOSE and return ETIMEDOUT. It will not notify the server when the port
is released, causing the server port remain.
when client's vsock_connect timeout，it should check sk state is
ESTABLISHED or not. if sk state is ESTABLISHED, it means the connection
is established, the client should not set the sk state to CLOSE
Note: I encountered this issue on kernel-4.18, which can be fixed by
this patch. Then I checked the latest code in the community
and found similar issue.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets") Signed-off-by: Zhuang Shengen <zhuangshengen@huawei.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
By default we would not want RXFCS and RXALL features enabled as they are
mainly intended for debugging purposes. This does not stop users from
enabling them later on as needed.
Fixes: 8e57daf70671 ("sfc_ef100: RX path for EF100") Signed-off-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com> Co-developed-by: Edward Cree <ecree.xilinx@gmail.com> Signed-off-by: Edward Cree <ecree.xilinx@gmail.com> Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As not all ICE_TX_FLAGS_* fit in current 16-bit limited
tx_flags field that was introduced in the Fixes commit,
VLAN-related information would be discarded completely.
As such, creating a vlan and trying to run ping through
would result in no traffic passing.
Fix that by refactoring tx_flags variable into flags only and
a separate variable that holds VLAN ID. As there is some space left,
type variable can fit between those two. Pahole reports no size
change to ice_tx_buf struct.
Fixes: aa1d3faf71a6 ("ice: Robustify cleaning/completing XDP Tx buffers") Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Pavilion 15 line has B&O top speakers similar to the x360 and
applying the same profile produces good sound. Without this, the
sound would be tinny and underpowered without either applying
model=alc295-hp-x360 or booting another OS first.
Signed-off-by: Ryan Underwood <nemesis@icequake.net> Fixes: 563785edfcef ("ALSA: hda/realtek - Add quirk entry for HP Pavilion 15") Link: https://lore.kernel.org/r/ZF0mpcMz3ezP9KQw@icequake.net Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This code was supposed to return an error code if init_stream()
failed, but it instead freed dg00x->rx_stream and returned success.
This potentially leads to a use after free.
Introduce the W/A for packet errors seen with short cables (<1m) between
two DP83867 PHYs.
The W/A recommended by DM requires FFE Equalizer Configuration tuning by
writing value 0x0E81 to DSP_FFE_CFG register (0x012C), surrounded by hard
and soft resets as follows:
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
The commit 565b4824c39f ("devlink: change port event netdev notifier
from per-net to global") changed original per-net notifier to be
per-devlink instance. That fixed the issue of non-receiving events
of netdev uninit if that moved to a different namespace.
That worked fine in -net tree.
However, later on when commit ee75f1fc44dd ("net/mlx5e: Create
separate devlink instance for ethernet auxiliary device") and
commit 72ed5d5624af ("net/mlx5: Suspend auxiliary devices only in
case of PCI device suspend") were merged, a deadlock was introduced
when removing a namespace with devlink instance with another nested
instance.
Here there is the bad flow example resulting in deadlock with mlx5:
net_cleanup_work -> cleanup_net (takes down_read(&pernet_ops_rwsem) ->
devlink_pernet_pre_exit() -> devlink_reload() ->
mlx5_devlink_reload_down() -> mlx5_unload_one_devl_locked() ->
mlx5_detach_device() -> del_adev() -> mlx5e_remove() ->
mlx5e_destroy_devlink() -> devlink_free() ->
unregister_netdevice_notifier() (takes down_write(&pernet_ops_rwsem)
Steps to reproduce:
$ modprobe mlx5_core
$ ip netns add ns1
$ devlink dev reload pci/0000:08:00.0 netns ns1
$ ip netns del ns1
Resolve this by converting the notifier from per-devlink instance to
a static one registered during init phase and leaving it registered
forever. Use this notifier for all devlink port instances created
later on.
Note what a tree needs this fix only in case all of the cited fixes
commits are present.
Reported-by: Moshe Shemesh <moshe@nvidia.com> Fixes: 565b4824c39f ("devlink: change port event netdev notifier from per-net to global") Fixes: ee75f1fc44dd ("net/mlx5e: Create separate devlink instance for ethernet auxiliary device") Fixes: 72ed5d5624af ("net/mlx5: Suspend auxiliary devices only in case of PCI device suspend") Signed-off-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230510144621.932017-1-jiri@resnulli.us Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On some distributions, the rp_filter is automatically set (=1) by
default on a netdev basis (also on VRFs).
In an SRv6 End.DT4 behavior, decapsulated IPv4 packets are routed using
the table associated with the VRF bound to that tunnel. During lookup
operations, the rp_filter can lead to packet loss when activated on the
VRF.
Therefore, we chose to make this selftest more robust by explicitly
disabling the rp_filter during tests (as it is automatically set by some
Linux distributions).
Fixes: 2195444e09b4 ("selftests: add selftest for the SRv6 End.DT4 behavior") Reported-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Tested-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The srv6_end_dt4_l3vpn_test instantiates a virtual network consisting of
several routers (rt-1, rt-2) and hosts.
When the IPv6 addresses of rt-{1,2} routers are configured, the Deduplicate
Address Detection (DAD) kicks in when enabled in the Linux distros running
the selftests. DAD is used to check whether an IPv6 address is already
assigned in a network. Such a mechanism consists of sending an ICMPv6 Echo
Request and waiting for a reply.
As the DAD process could take too long to complete, it may cause the
failing of some tests carried out by the srv6_end_dt4_l3vpn_test script.
To make the srv6_end_dt4_l3vpn_test more robust, we disable DAD on routers
since we configure the virtual network manually and do not need any address
deduplication mechanism at all.
Fixes: 2195444e09b4 ("selftests: add selftest for the SRv6 End.DT4 behavior") Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For errors after msm_submitqueue_get(), we need to drop the submitqueue
reference. Additionally after get_unused_fd() we need to drop the fd.
The ordering for dropping the queue lock and put_unused_fd() is not
important, so just move this all into out_post_unlock.
v2: Only drop queue ref if submit doesn't take it
v3: Fix unitialized submit ref in error path
v4: IS_ERR_OR_NULL()
Reported-by: pinkperfect2021@gmail.com Fixes: f0de40a131d9 drm/msm: ("Reorder lock vs submit alloc") Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/536073/ Link: https://lore.kernel.org/r/20230509203041.440619-1-robdclark@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
System-wide TSC read could cause a drift in C0 percentage calculation.
Because if first TSC is read and then one by one mperf is read for all
cpus, this introduces drift between mperf reading of later CPUs and TSC
reading. To lower this drift read TSC per CPU and also just after mperf
read. This technique improves C0 percentage calculation in Mperf monitor.
Jiri Slaby says:
> I bisected to this ... as it breaks nfs3-only servers in 6.3.
> I.e. /etc/nfs.conf containing:
> [nfsd]
> vers4=no
>
> The client sees:
> mount("10.0.2.15:/tmp", "/mnt", "nfs", 0, "vers=4.2,addr=10.0.2.15,clientad"...) = -1 EIO (Input/output error)
> write(2, "mount.nfs: mount system call fai"..., 45
> mount.nfs: mount system call failed for /mnt
>
> And the kernel says:
> nfs4_discover_server_trunking unhandled error -5. Exiting with error EIO
This fixes warning:
sm8250-xiaomi-elish-csot.dtb: dsi@ae94000: Unevaluated properties are not allowed ('qcom,master-dsi', 'qcom,sync-dual-dsi' were unexpected)
The INTF_FRAME_LINE_COUNT_EN, INTF_FRAME_COUNT and INTF_LINE_COUNT
registers are already defined higher up, in the right place when sorted
numerically.
SM8550 exclusively has a DITHER sub-block inside the PINGPONG block and
no other registers, hence the DITHER name of the macro and a
corresponding PINGPONG block length of zero. However, the PP_BLK_ macro
name was typo'd to DIPHER rather than DITHER.
UBWC and highest bank settings differ slightly between different DPU
units of the same generation, while the dpu_caps and dpu_mdp_cfg are
much more stable. To ease configuration reuse move ubwc_swizzle and
highest_bank_bit data to separate structure.
These blocks are of variable length on different SoCs. Set the
correct values where I was able to retrieve it from downstream
DTs and leave the old defaults (0x280) otherwise.
These blocks are of variable length on different SoCs. Set the
correct values where I was able to retrieve it from downstream
DTs and leave the old defaults (0x1c8) otherwise.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
[DB: fixed some of lengths, split the INTF changes away] Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/530814/ Link: https://lore.kernel.org/r/20230404130622.509628-3-dmitry.baryshkov@linaro.org Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Stable-dep-of: 701f69183d4d ("drm/msm/dpu: Fix PP_BLK_DIPHER -> DITHER typo") Signed-off-by: Sasha Levin <sashal@kernel.org>
The code doesn't use dpu_caps::smart_dma_rev field. It checks if the
corresponding feature is enabled in the SSPP features. Drop the
smart_dma_rev field completely.
Downstream driver uses dpu->caps->smart_dma_rev to update
sspp->cap->features with the bit corresponding to the supported SmartDMA
version. Upstream driver does not do this, resulting in SSPP subdriver
not enabling setup_multirect callback. Add corresponding SmartDMA SSPP
feature bits to dpu hw catalog.
Per Abhinav's request enable the SmartDMA features only on the platforms
where the multirect was actually verified visually (sdm845 and sm8250).
An (untested) enablement on the rest of the platforms comes in the next
patch.
These offsets do not fall under the MDP TOP block and do not fit the
comment right above. Move them to dpu_hw_interrupts.c next to the
repsective MDP_INTF_x_OFF interrupt block offsets.
The WB debug log mask ended up never being assigned, leading to writes
to this block to never be logged even if the mask is enabled in
dpu_hw_util_log_mask via debugfs.
while binding the code always registers a audio driver, however there
is no corresponding unregistration done in unbind. This leads to multiple
redundant audio platform devices if dp_display_bind and dp_display_unbind
happens multiple times during startup. On X13s platform this resulted in
6 to 9 audio codec device instead of just 3 codec devices for 3 dp ports.
Fix this by unregistering codecs on unbind.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Fixes: d13e36d7d222 ("drm/msm/dp: add audio support for Display Port on MSM") Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/533324/ Link: https://lore.kernel.org/r/20230421145657.12186-1-srinivas.kandagatla@linaro.org Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reverted commit clears the secpath on packets received via xfrm interfaces
to support nested IPsec tunnels. This breaks Netfilter policy matching using
xt_policy in the FORWARD chain, as the secpath is missing during forwarding.
Additionally, Benedict Wong reports that it breaks Transport-in-Tunnel mode.
Fix this regression by reverting the commit until we have a better approach
for nested IPsec tunnels.
Fixes: b0355dbbf13c ("Fix XFRM-I support for nested ESP tunnels") Link: https://lore.kernel.org/netdev/20230412085615.124791-1-martin@strongswan.org/ Signed-off-by: Martin Willi <martin@strongswan.org> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Failure to add offloaded policy will cause to the following
error once user will try to reload driver.
Unregister_netdevice: waiting for eth3 to become free. Usage count = 2
This was caused by xfrm_dev_policy_add() which increments reference
to net_device. That reference was supposed to be decremented
in xfrm_dev_policy_free(). However the latter wasn't called.
unregister_netdevice: waiting for eth3 to become free. Usage count = 2
leaked reference.
xfrm_dev_policy_add+0xff/0x3d0
xfrm_policy_construct+0x352/0x420
xfrm_add_policy+0x179/0x320
xfrm_user_rcv_msg+0x1d2/0x3d0
netlink_rcv_skb+0xe0/0x210
xfrm_netlink_rcv+0x45/0x50
netlink_unicast+0x346/0x490
netlink_sendmsg+0x3b0/0x6c0
sock_sendmsg+0x73/0xc0
sock_write_iter+0x13b/0x1f0
vfs_write+0x528/0x5d0
ksys_write+0x120/0x150
do_syscall_64+0x3d/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes: 919e43fad516 ("xfrm: add an interface to offload policy") Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current code doesn't let a simple "allow" policy counteract a
default policy blocking all incoming packets:
ip x p setdefault in block
ip x p a src 192.168.2.1/32 dst 192.168.2.2/32 dir in action allow
At this stage, we have an allow policy (with or without transforms)
for this packet. It doesn't matter what the default policy says, since
the policy we looked up lets the packet through. The case of a
blocking policy is already handled separately, so we can remove this
check.
Fixes: 2d151d39073a ("xfrm: Add possibility to set the default to block if we have no policy") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The panic notifiers' callbacks execute in an atomic context, with
interrupts/preemption disabled, and all CPUs not running the panic
function are off, so it's very dangerous to wait on a regular
spinlock, there's a risk of deadlock.
Refactor the panic notifier of parisc/power driver to make use
of spin_trylock - for that, we've added a second version of the
soft-power function. Also, some comments were reorganized and
trailing white spaces, useless header inclusion and blank lines
were removed.
projects / linux-stable / log